Add thermal support for R8A774A1 (RZ/G2M) SoC.
Based on the work done for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the I2C[0-6] and IIC Bus Interface for DVFS (IIC for DVFS)
devices nodes to the r8a774a1 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI nodes to the DT of the r8a774a1 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add GPIO device nodes to the DT of the r8a774a1 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (RWDT) controller on the Renesas
RZ/G2M (r8a774a1) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the SoC specific part of the Ethernet AVB
device tree node.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the Interrupt Controller for External Devices
(INTC-EX) on RZ/G2M.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all RZ/G2M SCIF and HSCIF serial ports,
incl. clocks, power domains and DMAs.
According to the HW user manual, SCIF[015] and HSCIF[012] are
connected to both SYS-DMAC1 and SYS-DMAC2, while SCIF[34] and
HSCIF[34] are connected to SYS-DMAC0.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor/V3HSK board dependent parts of the DU and LVDS device
nodes. Also add the device nodes for Thine THC63LVD1024 LVDS decoder and
Analog Devices ADV7511W HDMI transmitter...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the eMMC chip support for the V3M Started Kit board.
Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 part of the MMC0 (SDHI2) device node.
Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds OPPs table for CA57{0,1} cpu devices
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
[simon: do not give nodes unit names as they have no bus addresses]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Allow the bare M3-N-based ULCB board to boot.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to R-Car Gen3 HW manual rev1.00, R-Car M3-N has two CAN
interfaces, similar to H3, M3-W and other SoCs from the same family.
Add CAN placeholder nodes to avoid below DTC errors:
Error: arch/arm64/boot/dts/renesas/ulcb-kf.dtsi:19.1-6 Label or path can0 not found
Error: arch/arm64/boot/dts/renesas/ulcb-kf.dtsi:25.1-6 Label or path can1 not found
These errors occur *after* the addition of r8a77965-m3nulcb-kf.dts.
Fix them beforehand.
CAN support is inspired from below commits:
- v4.7 commit 308b7e4ba6 ("arm64: dts: r8a7795: Add CAN support")
- v4.11 commit 909c162524 ("arm64: dts: r8a7796: Add CAN support")
- v4.12 commit bec0948e81 ("arm64: dts: r8a7796: Add reset control properties")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
[simon: make placeholder minimal by only including reg property]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For R-Car M3-N hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to
IPMMU-DS0 and IPMMU-DS1 in same way as for R-Car M3-W.
This follows the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the RZ/G2M SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Ensure that the ADV748x device addresses do not conflict, and group them
together (visually in i2cdetect)
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the CSI2 and VIN (and their interconnections) in the R8A77980
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the nodes to enable SATA. Note that MD12 (SW12-7) must be switched
off for that to work.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds SATA controller node for the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[wsa: rebased to upstream base]
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The CAN clock node should precede the "cpus" node in the R8A779{7|8}0
device trees, according to the alphanumeric node sorting rule...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The IPMMU nodes should follow the GEther node, not the CAN-FD node,
according to the <unit-address> part of the startng IPMMU-DS1 node.
While moving the nodes, also do sort them by label alphanumerically...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds PWM device nodes and enables PWM3 and PWM5 for
R-Car E3 Ebisu board. These devices are used for backlight control.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the performance monitor unit (PMU) for the Cortex-A53 cores in
the R8A77980 SoC's device tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The internal LVDS encoder now has DT bindings separate from the DU. Port
the r8a7795 and r8a7796 device trees over to the new model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to IPMMU-DS0 and IPMMU-DS1
following the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Browsing the DTS for all the R-Car SoCs with similar part numbers
makes my head hurt, so to improve the user friendliness of the
DTS code base include R-Car product name in each DTSI file.
Product names are derived from
Documentation/devicetree/bindings/arm/shmobile.txt
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe RWDT in the R8A77980 SoC device tree.
Enable RWDT on the Condor and V3H Starter Kit boards.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the INTC-EX interrupt controller in the R8A77980 device tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds and USB3.0 host device node and enable it for
R-Car E3 Ebisu board.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the device nodes for SCIF {0,1,3,4,5} and all HSCIF serial
ports, incl. clocks, power domain and DMAs.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU device nodes for the R-Car M3-N (r8a77965),
V3H (r8a77980) and E3 (r8a77990) SoCs.
* The r8a77965 IPMMU is quite similar to r8a7796 however VP0
has been added and PV1 has been removed. Also the IMSSTR
bit assignment has been reworked.
* The r8a77980 IPMMU is quite similar to r8a77970 however VC0
has been added. The IMSSTR bit assignment has also been
reworked. Power domains are also quite different however the
the documentation is rather unclear about this topic.
Until we know better VC0 gets assigned to R8A77980_PD_ALWAYS_ON.
* The r8a77990 IPMMU is similar to r8a77995. Power domains are
however different and the public documentation is still unclear.
Based on preliminary information from the hardware team the R-Car E3
SoC comes with an IPMMU-VP0 device in an Always-on power domain and
the IPMMU-VC0 is placed as expected in the A3VC power domain.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The labels for RWDT device node were named as 2 types now:
- wdt0: r8a7795, r8a7796, r8a77965.
- rwdt: r8a77970, r8a77990, r8a77995.
To be made consistent, this patch unifis the labels as the hardware
name "rwdt".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
HSCIF is superior to SCIF (larger FIFOs, more accurate and wider
supported range of bitrates).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This node is just a placeholder but fills that function better if it does
not trigger build warnings. This update satisfies the requirement that
nodes with #address-cells/#size-cells properties have more than one child
node.
This is flagged by dtc as follows:
# make dtbs W=1
arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dtb: Warning (graph_child_address): /soc/sound@ec500000/ports: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dtb: Warning (graph_child_address): /soc/sound@ec500000/ports: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
With recent dtc and W=1:
...salvator-x.dtb: Warning (graph_port): /soc/i2c@e66d8000/video-receiver@70/port@10: graph node unit address error, expected "a"
...salvator-x.dtb: Warning (graph_port): /soc/i2c@e66d8000/video-receiver@70/port@11: graph node unit address error, expected "b"
Unit addresses are always hexadecimal (without prefix), while the bases
of reg property values depend on their prefixes.
Fixes: 908001d778 ("arm64: dts: renesas: salvator-common: Add ADV7482 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car E3 does not have the Stream Buffer for EtherAVB-IF (STBE).
Note that the RAVB driver does not use this region.
Fixes: 913a78b575 ("arm64: dts: renesas: r8a77990: Add EthernetAVB device nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds pin control for HSCIF1, and supports connection with
Debug Serial-1 (CN26) on Salvator boards.
SCIF1 and HSCIF1 are sharing the pins connected to Debug Serial-1 (CN26)
on Salvator boards, and it is necessary to ensure that either SCIF1 or
HSCIF1 is enabled, not both.
As for the default of this DeviceTree, SCIF1 is connected.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Add missing "uart-has-rtscts"]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the interconnected FCPVD0, VSPD0, DU, and LVDS0 devices in the
R8A77980 device tree...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify Ethernet PHY IRQs in the Condor/V3HSK board device trees, now that
we have the GPIO support (previously phylib had to resort to polling).
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds PCIe{0,1} device nodes to R8A77965 SoC.
Based on a similar patches of the R8A7796 device tree
by Harunobu Kurokawa <harunobu.kurokawa.dn@renesas.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The VSPD and FCPVD nodes have overlapping register ranges, as the FCPVD
devices are mapped in the memory range usually used by the VSP LUT and
CLU, which are not present in the VSPD. Fix this by shortening the VSPD
registers range to 0x5000.
Fixes: 9f8573e38a ("arm64: dts: renesas: r8a7795: Add VSP instances")
Fixes: 291e0c4994 ("arm64: dts: r8a7795: Add support for R-Car H3 ES2.0")
Fixes: f06ffdfbdd ("arm64: dts: r8a7796: Add VSP instances")
Fixes: b4f92030d5 ("arm64: dts: renesas: r8a77970: add VSPD support")
Fixes: 295952a183 ("arm64: dts: renesas: r8a77995: add VSP instances")
Fixes: 85cb322921 ("arm64: dts: renesas: r8a77965: Add VSP instances")
Reported-by: Simon Horman <horms+renesas@verge.net.au>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe all 6 GPIO controllers in the R8A77980 device tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds USB2.0 PHY and Host(EHCI/OHCI) nodes and
enables them for R-Car E3 Ebisu board.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the second Cortex-A53 CPU core on the Renesas
R-Car E3 (r8a77990) SoC, and adjust the interrupt delivery masks for ARM
Generic Interrupt Controller and Architectured Timer.
Based on a patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (WDT) controller on the
R8A77990 SoC, and enable the watchdog on the Ebisu board.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Squashed 2 commits]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor board dependent part of the I2C0 device node.
The I2C0 bus is populated by 2 ON Semiconductor PCA9654 I/O expanders
and Analog Devices ADV7511W HDMI transmitter (but we're only describing
the former chips now).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77980 parts of the I2C[0-5] device nodes.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Any of the following devices connected to I2C ch4 of the Salvator-X(S)
boards will operate at 400 kHz:
PCA9654, 9FGV0841, ADV7482WBBCZ, MAX9611, 5P49V5923, 5P49V6901A
This patch updates the clock frequency to 400 KHz.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[wsa: squashed commits into one]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds definitions for configuration of the power-source,
drive-strength, etc... for the SD2_DS pin for Salvator-X(S) and ULCB
boards.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[wsa: fixed for ULCB boards, too]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Based on a similar patch of the R8A7796 device tree
by Ulrich Hecht <ulrich.hecht+renesas@gmail.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the hardcoded clock indices by R8A77965_CLK_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add bindings for CryptoCell instance in the SoC.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (WDT) controller on the Renesas
R-Car M3-N (R8A77965) SoC.
Based on a similar patch of the R8A7796 device tree
by Geert Uytterhoeven <geert+renesas@glider.be>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the V3H Starter Kit board dependent part of the GEther device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77980 part of the GEther device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: add resets property]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for 3 more Cortex-A53 CPU cores; adjust the interrupt
delivery masks for the ARM GIC and Architectured Timer.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: corrected whitespace]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe HDMI input connector and ADV7612 HDMI decoder installed on
R-Car Gen3 Draak board.
The video signal routing to the HDMI decoder to the video input interface
VIN4 is multiplexed with CVBS input path, and enabled/disabled through
on-board switches SW-49, SW-50, SW-51 and SW-52.
As the default board switches configuration connects CVBS input to VIN4,
leave the HDMI decoder unconnected in DTS.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe CVBS video input through analog video decoder ADV7180
connected to video input interface VIN4.
The video input signal path is shared with HDMI video input, and
selected by on-board switches SW-53 and SW-54 with CVBS input selected
by the default switches configuration.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The compat string renesas,gpio-rcar has been deprecated since v4.14,
the same release that r8a77990 SoC support was added. Thus
renesas,gpio-rcar can safely be removed without any risk of behaviour
changes between old and new mainline kernels and DTBs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add power domain information to the R-Car D3 IPMMU device nodes.
As specified by the data sheet, all the IPMMU devices are always on.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Salvator boards use an ADV7482 receiver for HDMI and CVBS inputs.
Provide ADV7482 node on the i2c4 bus, along with connectors for the
hdmi and cvbs inputs, and link to the csi20 and csi40 nodes as outputs.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Renesas H3 ES1.0 have one extra CSI-2 node, CSI21 which is not present
for later ES versions of H3.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables EthernetAVB for r8a77990 Ebisu board.
Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds EthernetAVB node for r8a77990 (R-Car E3).
Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds GPIO nodes for r8a77990 (R-Car E3).
Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[simon: dropped use of deprecated "renesas,gpio-rcar"]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the V3H Starter Kit board.
The board has 1 debug serial port (SCIF0); include support for it,
so that the serial console can work.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When adding the R8A77980 EtherAVB device I failed to notice that it does
not have the usual "status" property disabling the described devices in
anticipation that the board device trees enable the devices according to
their needs. This causes the EtherAVB driver to successfully probe despite
e.g. the needed pins not having been configured -- luckily, "eth<n>" device
can't be opened anyway...
Fixes: bf6f90832f ("arm64: dts: renesas: r8a77980: add EtherAVB support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When adding the R8A77970 EtherAVB device I failed to notice that it does
not have the usual "status" property disabling the described devices in
anticipation that the board device trees enable the devices according to
their needs. This causes the EtherAVB driver to successfully probe despite
e.g. the needed pins not having been configured -- luckily, "eth<n>" device
can't be opened anyway...
Fixes: bea2ab136e ("arm64: dts: renesas: r8a77970: add EtherAVB support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add resets property to CAN-FD node to describe it in the reset topology of
on-SoC devices. This allows to reset the CAN-FD device using the Reset
Controller API.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the performance monitor unit for the Cortex-A53 cores on the
R-Car V3M (r8a77970) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the second Cortex-A53 CPU core on the Renesas
R-Car V3M (r8a77970) SoC, and adjust the interrupt delivery masks for
ARM Generic Interrupt Controller and Architectured Timer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI nodes to the DT of the r8a77965 SoC.
Based on several similar patches of the R8A7796 device tree
by Simon Horman <horms+renesas@verge.net.au>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On the R-Car Starter Kit Premier/Pro, all of the DDR0, DDR1, DDR0C, and
DDR1C power rails need to be kept powered when backup mode is enabled.
Reflect this in the "rohm,ddr-backup-power" property for the BD9571MWV
PMIC node.
The accessory power switch (SW8) is a momentary switch, hense specify
"rohm,rstbmode-pulse".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On Salvator-X(S), all of the DDR0, DDR1, DDR0C, and DDR1C power rails
need to be kept powered when backup mode is enabled. Reflect this in
the "rohm,ddr-backup-power" property for the BD9571MWV PMIC node.
The accessory power switch (SW23) is a toggle switch, hence specify
"rohm,rstbmode-level".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the ROHM BD9571MWV PMIC.
This was based on the example in the DT binding documentation, but using
IRQ0 instead of a GPIO interrupt, as that matches the schematics, and
because INTC-EX is a simpler block.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add missing spaces after commas.
Replace 8 consecutive spaces by a TAB.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables USB2.0 host channel 3 for r8a7795 with Salvator-XS.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables HS-USB channel3 node for r8a7795 with Salvator-XS.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables usb2_phy3 node for r8a7795 with Salvator-XS.
You must change the SW31 to OFF-OFF-ON-ON-ON-ON on the board.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the EEPROM found on Salvator-X and -XS boards for H3, M3-W, and M3-N
on the IIC_DVFS bus.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor board dependent part of the CAN-FD device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77980 part of the CAN-FD device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[simon: consistently use tabs for indentation]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Eagle board dependent part of the CAN-FD device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 part of the CAN-FD device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Based on previous work by Ryo Kataoka <ryo.kataoka.wt@renesas.com>.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[simon: moved thermal node to preseve ordering of nodes by bus address]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the hardcoded power domain indices by R8A77965_PD_* symbols.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
[simon: dropped hunk to include r8a77965-sysc.h which is already present]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the commit 7755b40d07 ("dt-bindings: power: add R8A77980 SYSC
power domain definitions") has hit Linus' tree, we can replace the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the commit 35b3c462da ("dt-bindings: clock: add R8A77980 CPG
core clock definitions") has hit Linus' tree, we can replace the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The rcar_sound port nodes have unit names and thus should have register
properties.
This is flagged by dtc as follows:
# make dtbs W=1
...
DTC arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
DTC arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
Prior to this patch the port nodes only defined in board DTS files.
As the register properties are common this patch defines the port nodes
and provides register properties in the SoC DTS file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The rcar_sound port nodes have unit names and thus should have register
properties.
This is flagged by dtc as follows:
# make dtbs W=1
...
DTC arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property
...
DTC arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property
Prior to this patch the port nodes only defined in board DTS files.
As the register properties are common this patch defines the port nodes
and provides register properties in the SoC DTS file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The rcar_sound port nodes have unit names and thus should have register
properties.
This is flagged by dtc as follows:
# make dtbs W=1
...
DTC arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@2: node has a unit name, but no reg property
...
DTC arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@2: node has a unit name, but no reg property
DTC arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@2: node has a unit name, but no reg property
Prior to this patch the port nodes only defined in board DTS files.
As the register properties are common this patch defines the port nodes
and provides register properties in the SoC DTS file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Define the V3M Starter Kit board dependent part of the DU and LVDS device
nodes. Also add the device nodes for Thine THC63LVD1024 LVDS decoder and
Analog Devices ADV7511W HDMI transmitter...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor board dependent part of the MMC0 (connected to eMMC chip)
device node along with the necessary voltage regulators...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU1 external dot clock is provided by the fixed frequency clock
generator X21, while the DU0 and DU3 clocks are provided by the
programmable Versaclock6 clock generator.
Enable the clocks, and the HDMI encoder for the M3-N Salvator-XS, and
hook it up to the HDMI connector
Based on patches from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU1 external dot clock is provided by the fixed frequency clock
generator X21, while the DU0 and DU3 clocks are provided by the
programmable Versaclock5 clock generator.
Enable the clocks, and the HDMI encoder for the M3-N Salvator-X board
and hook it up to the HDMI connector.
Based on patches from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the HDMI encoder to the R8A77965 DT in disabled state.
Based on a similar patch of the R8A7796 device tree
by Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Kieran: Rebase to top of tree]
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU entity node has been previously added but only as a placeholder.
Populate the node with the properties to use the device.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a77965 has 4 VSP instances.
Based on a similar patch of the R8A7796 device tree
by Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Kieran: Rebased to top of tree, fixed sort orders]
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The FCPs handle the interface between various IP cores and memory. Add
the instances related to the FDPs and VSP2s.
Based on a similar patch of the R8A7796 device tree
by Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Kieran: Rebase to top of tree]
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The cache controller node should not have unit-addresses and reg
properties. So, this patch removes them.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The basic support patch 9491a8b17530 ("arm64: dts: renesas: Add Renesas
R8A77990 SoC support") lacks the compatible "arm,psci-1.0" in the psci
node. So, this patch revises it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove 'status = "disabled"' to make sure all IPMMU devices are enabled
in DT on the r8a7795 ES1.0 Soc.
This is a follow up for a patch by Magnus Damm for the
the r8a7795 ES2.0 and other R-Car Gen 3 SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Sound is using simple-audio-card which can't support HDMI.
To use HDMI sound, we need to use audio-graph-card.
But, one note is that r8a7795 has 2 HDMI ports, but r8a7796 has 1.
Because of this mismatch, supporting HDMI on salvator-common is
impossible.
Thus, this patch exchange sound card to audio-graph-card and keep
supporting ak4613 as 1st sound node.
r8a7795/r8a7796 salvator-x{s} need to add HDMI sound individually.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77980 part of the MMC0 (SDHI2) device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) EtherAVB pin data to the Condor board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) SCIF0 pin data to the Condor board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77980 part of the PFC device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) EtherAVB pin data to the V3M Starter Kit
board's device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) EtherAVB pin data to the Eagle board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, now the pinctrl drivers for
R-Car H3, M3-W, and M3-N have gained support for the traditional pin
group name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, now the pinctrl drivers for
R-Car H3, M3-W, and M3-N have gained support for the traditional pin
group name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, now the pinctrl drivers for
R-Car H3, M3-W, and M3-N have gained support for the traditional pin
group name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove 'status = "disabled"' to make sure all IPMMU devices are enabled
in DT on the r8a77995 SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: rebased]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove 'status = "disabled"' to make sure all IPMMU devices are enabled
in DT on the r8a77970 SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: rebased]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove 'status = "disabled"' to make sure all IPMMU devices are enabled
in DT on the r8a7796 SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove 'status = "disabled"' to make sure all IPMMU devices are enabled
in DT on the r8a7795 SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the Renesas Ebisu board based on R-Car E3:
- Memory,
- Main crystal,
- Serial console,
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[shimoda: rebase and add SPDX-License-Identifier]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds basic support for the Renesas R-Car E3 (R8A77990) SoC:
- PSCI
- CPU (single)
- Cache controller
- Main clocks and controller
- Interrupt controller
- Timer
- PMU
- Reset controller
- Product register
- System controller
- UART for console
Inspried by a patch by Takeshi Kihara in the BSP.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sort subnodes of the soc node.
- The primary key is the bus address.
- The secondary key is the IP block.
- The tertiary key is the node name.
This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[simon: rebased; move fcpvd0 to after vspd0]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sort subnodes of the soc node.
- The primary key is the bus address.
- The secondary key is the IP block.
- The tertiary key is the node name.
This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sort subnodes of the root node alphanumerically.
This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sort subnodes of the soc node.
- The primary key is the bus address.
- The secondary key is the IP block.
- The tertiary key is the node name.
This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sort subnodes of the root node alphanumerically.
This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable HDMI output on Renesas R-Car V3M Eagle board.
The HDMI output is enabled connecting the DU LVDS output to the
transparent LVDS converter THC63LVD1024, and successively routing its
RGB output to the ADV7511W HDMI encoder.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[for THC63LVD1024: ]
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 part of the LVDS device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 part of the DU device node.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe VSPD0 in the R8A77970 device tree; it will be used by DU in
the next patch...
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
To incorporate more tests by the hardware team decrease the hysteresis
value to 1C.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
To incorporate more tests by the hardware team decrease the hysteresis
value to 1C.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe FCPVD0 in the R8A77970 device tree; it will be used by VSPD0 in
the next patch...
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all MSIOF SPI controllers.
Based on several similar patches of the R8A7796 device tree
by Geert Uytterhoeven <geert+renesas@glider.be>
and Simon Horman <horms+renesas@verge.net.au>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Use numerical power domain indices for initial r8a77965.dtsi]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sort subnodes of the soc node.
- The primary key is the bus address.
- The secondary key is the IP block.
- The tertiary key is the node name.
This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.
This should not have any run-time effect.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort subnodes of the root node alphanumerically.
This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.
Also remove excessive line-wrapping of interrupts-extended property of
timer node.
This should not have any run-time effect.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort subnodes of the soc node.
- The primary key is the bus address.
- The secondary key is the IP block.
- The tertiary key is the node name.
This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.
This should not have any run-time effect.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort subnodes of the root node alphanumerically.
This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.
This should not have any run-time effect.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Judging by "R-Car-Gen3-rev0.80" IPMMU IMSSTR register documentation
for [R-Car V3M] the DS1 bit field should be bit 0.
Update the ipmmu-main property to make it match the data sheet.
Fixes: ce3b52a159 ("arm64: dts: renesas: r8a77970: Add IPMMU device nodes")
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds USB 3.0 peripheral node for r8a77965.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds USB 3.0 host node for r8a77965.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds HS-USB node for r8a77965.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds USB-DMAC nodes for r8a77965.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds USB 2.0 host (EHCI/OHCI) nodes for r8a77965.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds usb3_phy node for r8a77965.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch add usb2_phy nodes for r8a77965.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) SCIF0 pin data to the V3M Starter Kit board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On R-Car H3, on-chip peripheral modules that can make use of DMA are
wired to either SYS-DMAC0 only, or to both SYS-DMAC1 and SYS-DMAC2.
Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
SCIF[0125], and I2C[0-2]. These were initially left out because early
firmware versions prohibited using SYS-DMAC2. This restriction has been
lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25, 2016).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add r8a7795 IPMMU-PV1 and keep it disabled by default.
This device is not present in r8a7795 ES1.x and
is removed from the DT of those SoCs.
This corrects an omission in
3b7e7848f0 ("arm64: dts: renesas: r8a7795: Add IPMMU device nodes")
This does not have any runtime effect.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Sort root sub-nodes alphabetically for allow for easier maintenance of
this file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Eagle board dependent part of the I2C0 device node.
The I2C0 bus is populated by ON Semiconductor PCA9653 I/O expander and
Analog Devices ADV7511W HDMI transmitter (but we're only describing the
former chip now).
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 parts of the I2C[0-4] device node.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-XS boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the V3MSK board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii"
mode and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Eagle board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Draak board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77995 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the ULCB board provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96 SoC DTSI to use "rgmii" mode\
and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Salvator-X[S] board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96/965 SoC DTSI to use "rgmii"
mode and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Populate the device node for the Interrupt Controller for External
Devices (INTC-EX) on R-Car M3-N, which serves external IRQ pins
IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Populate the device node for the IIC Bus Interface for DVFS (IIC for
DVFS) on R-Car M3-N, and add an alias to fix its bus number.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the Renesas Salvator-XS (Salvator-X 2nd version)
development board equipped with an R-Car M3-N SiP.
Most features are enabled through the shared salvator-xs.dtsi board
description. The memory configuration is specific to the M3-N SiP.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Switch to SPDX-License-Identifier, update patch description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#interrupt-cells" property and "interrupt-controller" label to
"interrupt-controller@e61c0000" device node.
This silences the following DTC compiler warnings:
Warning (interrupts_property): Missing interrupt-controller or
interrupt-map property in /soc/interrupt-controller@e61c0000
Warning (interrupts_property): Missing #interrupt-cells in
interrupt-parent /soc/interrupt-controller@e61c000
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#pwm-cells" property to "pwm@e6e31000" device node.
This silences the following DTC compiler warning:
Warning (pwms_property): Missing property '#pwm-cells' in node
/soc/pwm@e6e31000 or bad phandle (referred from /backlight:pwms[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#phy-cells" property to "usb-phy@e65ee000" device node.
This silences the following DTC compiler warning:
Warning (phys_property): Missing property '#phy-cells' in node
/soc/usb-phy@e65ee000 or bad phandle (referred from
/soc/usb@ee020000:phys[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove "reg" property from cache-controller-0 device node as it does not
have any unit address.
This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /cpus/cache-controller-0 has a reg
or ranges property, but no unit name
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#address-cells" and "#size-cells" properties to all place-holder nodes
that have children nodes defined by salvator-x[s].dtsi device tree.
This silences the following DTC compiler warnings:
Warning (reg_format): "reg" property in /soc/.. has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells
value for /soc/...
Warning (avoid_default_addr_size): Relying on default #size-cells value
for /soc/...
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "reg" properties to place-holder nodes with unit address defined for
R-Car M3-N SoC.
This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /soc/... has a unit name,
but no reg property
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add basic support for R-Car Salvator-X M3-N (R8A77965) board.
Based on original work from:
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>