media_build/v4l/drxk_hard.c: In function 'DownloadMicrocode':
media_build/v4l/drxk_hard.c:1388:6: warning: variable 'BlockCRC' set but not used [-Wunused-but-set-variable]
media_build/v4l/drxk_hard.c:1384:6: warning: variable 'Drain' set but not used [-Wunused-but-set-variable]
media_build/v4l/drxk_hard.c:1383:6: warning: variable 'Flags' set but not used [-Wunused-but-set-variable]
media_build/v4l/lmedm04.c: In function 'lme2510_probe':
media_build/v4l/lmedm04.c:1208:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/hopper_cards.c: In function 'hopper_irq_handler':
media_build/v4l/hopper_cards.c:68:26: warning: variable 'lstat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_cards.c: In function 'mantis_irq_handler':
media_build/v4l/mantis_cards.c:76:26: warning: variable 'lstat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_dma.c: In function 'mantis_dma_stop':
media_build/v4l/mantis_dma.c:202:16: warning: variable 'mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_dma.c:202:6: warning: variable 'stat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_evm.c: In function 'mantis_hifevm_work':
media_build/v4l/mantis_evm.c:44:17: warning: variable 'gpif_mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c: In function 'stb0899_init_calc':
media_build/v4l/stb0899_drv.c:640:5: warning: variable 'agc1cn' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c: In function 'stb0899_diseqc_init':
media_build/v4l/stb0899_drv.c:830:13: warning: variable 'f22_rx' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c:826:31: warning: variable 'tx_data' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv0900_sw.c: In function 'stv0900_track_optimization':
media_build/v4l/stv0900_sw.c:838:26: warning: variable 'rolloff' set but not used [-Wunused-but-set-variable]
media_build/v4l/ir-sanyo-decoder.c: In function 'ir_sanyo_decode':
media_build/v4l/ir-sanyo-decoder.c:59:14: warning: variable 'not_address' set but not used [-Wunused-but-set-variable]
media_build/v4l/mceusb.c: In function 'mceusb_dev_printdata':
media_build/v4l/mceusb.c:523:46: warning: variable 'data5' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
if the AGC2 > 1400 then no signal on this frequency for STV0900 Cut 3.0. For
Cut 2.0 this value is 700.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The functions stv0900_sw_algo() and stv0900_set_dvbs1_track_car_loop() are only used
locally so mark them static.
This will remove the following sparse warnings (see "make C=1"):
* symbol 'stv0900_sw_algo' was not declared. Should it be static?
* symbol 'stv0900_set_dvbs1_track_car_loop' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card based on stv0903 demod, stb6100 tuner.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch 4 of 4.
Also patch changes logic to prevent code repetitions and big indents.
It makes checkpatch silent :)
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add last piece of code to support ST STV0900 dual demodulator.
The IC consist of two dependent parts.
It may use single or dual mode.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
