IP transports will most likely use the same controller options
matching when detecting a duplicate connect. Move it to
fabrics.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When an io is rejected by nvmf_check_ready() due to validation of the
controller state, the nvmf_fail_nonready_command() will normally return
BLK_STS_RESOURCE to requeue and retry. However, if the controller is
dying or the I/O is marked for NVMe multipath, the I/O is failed so that
the controller can terminate or so that the io can be issued on a
different path. Unfortunately, as this reject point is before the
transport has accepted the command, blk-mq ends up completing the I/O
and never calls nvme_complete_rq(), which is where multipath may preserve
or re-route the I/O. The end result is, the device user ends up seeing an
EIO error.
Example: single path connectivity, controller is under load, and a reset
is induced. An I/O is received:
a) while the reset state has been set but the queues have yet to be
stopped; or
b) after queues are started (at end of reset) but before the reconnect
has completed.
The I/O finishes with an EIO status.
This patch makes the following changes:
- Adds the HOST_PATH_ERROR pathing status from TP4028
- Modifies the reject point such that it appears to queue successfully,
but actually completes the io with the new pathing status and calls
nvme_complete_rq().
- nvme_complete_rq() recognizes the new status, avoids resetting the
controller (likely was already done in order to get this new status),
and calls the multipather to clear the current path that errored.
This allows the next command (retry or new command) to select a new
path if there is one.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----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=b9ib
-----END PGP SIGNATURE-----
Merge tag 'for-4.19/block-20180812' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"First pull request for this merge window, there will also be a
followup request with some stragglers.
This pull request contains:
- Fix for a thundering heard issue in the wbt block code (Anchal
Agarwal)
- A few NVMe pull requests:
* Improved tracepoints (Keith)
* Larger inline data support for RDMA (Steve Wise)
* RDMA setup/teardown fixes (Sagi)
* Effects log suppor for NVMe target (Chaitanya Kulkarni)
* Buffered IO suppor for NVMe target (Chaitanya Kulkarni)
* TP4004 (ANA) support (Christoph)
* Various NVMe fixes
- Block io-latency controller support. Much needed support for
properly containing block devices. (Josef)
- Series improving how we handle sense information on the stack
(Kees)
- Lightnvm fixes and updates/improvements (Mathias/Javier et al)
- Zoned device support for null_blk (Matias)
- AIX partition fixes (Mauricio Faria de Oliveira)
- DIF checksum code made generic (Max Gurtovoy)
- Add support for discard in iostats (Michael Callahan / Tejun)
- Set of updates for BFQ (Paolo)
- Removal of async write support for bsg (Christoph)
- Bio page dirtying and clone fixups (Christoph)
- Set of bcache fix/changes (via Coly)
- Series improving blk-mq queue setup/teardown speed (Ming)
- Series improving merging performance on blk-mq (Ming)
- Lots of other fixes and cleanups from a slew of folks"
* tag 'for-4.19/block-20180812' of git://git.kernel.dk/linux-block: (190 commits)
blkcg: Make blkg_root_lookup() work for queues in bypass mode
bcache: fix error setting writeback_rate through sysfs interface
null_blk: add lock drop/acquire annotation
Blk-throttle: reduce tail io latency when iops limit is enforced
block: paride: pd: mark expected switch fall-throughs
block: Ensure that a request queue is dissociated from the cgroup controller
block: Introduce blk_exit_queue()
blkcg: Introduce blkg_root_lookup()
block: Remove two superfluous #include directives
blk-mq: count the hctx as active before allocating tag
block: bvec_nr_vecs() returns value for wrong slab
bcache: trivial - remove tailing backslash in macro BTREE_FLAG
bcache: make the pr_err statement used for ENOENT only in sysfs_attatch section
bcache: set max writeback rate when I/O request is idle
bcache: add code comments for bset.c
bcache: fix mistaken comments in request.c
bcache: fix mistaken code comments in bcache.h
bcache: add a comment in super.c
bcache: avoid unncessary cache prefetch bch_btree_node_get()
bcache: display rate debug parameters to 0 when writeback is not running
...
When the user supplies a ctrl_loss_tmo < 0, we warn them that this will
cause the fabrics layer to attempt reconnection forever. However, in
reality the fabrics layer never attempts to reconnect because the
condition to test whether we should reconnect is backwards in this case.
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The revised if_ready checks skipped over the case of returning error when
the controller is being deleted. Instead it was returning BUSY, which
caused the ios to retry, which caused the ns delete to hang waiting for
the ios to drain.
Stack trace of hang looks like:
kworker/u64:2 D 0 74 2 0x80000000
Workqueue: nvme-delete-wq nvme_delete_ctrl_work [nvme_core]
Call Trace:
? __schedule+0x26d/0x820
schedule+0x32/0x80
blk_mq_freeze_queue_wait+0x36/0x80
? remove_wait_queue+0x60/0x60
blk_cleanup_queue+0x72/0x160
nvme_ns_remove+0x106/0x140 [nvme_core]
nvme_remove_namespaces+0x7e/0xa0 [nvme_core]
nvme_delete_ctrl_work+0x4d/0x80 [nvme_core]
process_one_work+0x160/0x350
worker_thread+0x1c3/0x3d0
kthread+0xf5/0x130
? process_one_work+0x350/0x350
? kthread_bind+0x10/0x10
ret_from_fork+0x1f/0x30
Extend nvmf_fail_nonready_command() to supply the controller pointer so
that the controller state can be looked at. Fail any io to a controller
that is deleting.
Fixes: 3bc32bb118 ("nvme-fabrics: refactor queue ready check")
Fixes: 35897b920c ("nvme-fabrics: fix and refine state checks in __nvmf_check_ready")
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
- make sure we only allow internally generates commands in any non-live
state
- only allow connect commands on non-live queues when actually in the
new or connecting states
- treat all other non-live, non-dead states the same as a default
cach-all
This fixes a regression where we could not shutdown a controller
orderly as we didn't allow the internal generated Property Set
command, and also ensures we don't accidentally let a Connect command
through in the wrong state.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Move the is_connected check to the fibre channel transport, as it has no
meaning for other transports. To facilitate this split out a new
nvmf_fail_nonready_command helper that is called by the transport when
it is asked to handle a command on a queue that is not ready.
Also avoid a function call for the queue live fast path by inlining
the check.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Only take nvmf_transports_rwsem when doing a lookup of registered
transports, so that a blocking ->create_ctrl doesn't prevent other
actions on /dev/nvme-fabrics.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
[hch: increased lock hold time a bit to be safe, added a comment
and updated the changelog]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Without this we can't cleanly shut down.
Based on analysis an an earlier patch from Hannes Reinecke.
Fixes: bb06ec3145 ("nvme: expand nvmf_check_if_ready checks")
Reported-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: James Smart <james.smart@broadcom.com>
The host nqn actually is smaller than the space reserved for it,
so we should be using strlcpy to keep KASAN happy.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The whole point of the discovery controller is that it can accept
multiple connections. Additionally the cmic field is not even defined for
the discovery controller identify page.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When connecting to the discovery controller we have certain defaults
to observe, so centralize them to avoid inconsistencies due to argument
ordering.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
After creating the nvme controller, nvmf_create_ctrl() validates
the newly created subsysnqn vs the one specified by the options.
In general, this is an unnecessary check as the Connect message
should implicitly ensure this value matches.
With the change to the FC transport to do an asynchronous connect
for the first association create, the transport will return to
nvmf_create_ctrl() before that first association has been established,
thus the subnqn will not yet be set.
Remove the unnecessary validation.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When specifying same string type option several times,
current option parsing may cause memory leak. Hence,
call kfree for previous one in this case.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The nvmf_check_if_ready() checks that were added are very simplistic.
As such, the routine allows a lot of cases to fail ios during windows
of reset or re-connection. In cases where there are not multi-path
options present, the error goes back to the callee - the filesystem
or application. Not good.
The common routine was rewritten and calling syntax slightly expanded
so that per-transport is_ready routines don't need to be present.
The transports now call the routine directly. The routine is now a
fabrics routine rather than an inline function.
The routine now looks at controller state to decide the action to
take. Some states mandate io failure. Others define the condition where
a command can be accepted. When the decision is unclear, a generic
queue-or-reject check is made to look for failfast or multipath ios and
only fails the io if it is so marked. Otherwise, the io will be queued
and wait for the controller state to resolve.
Admin commands issued via ioctl share a live admin queue with commands
from the transport for controller init. The ioctls could be intermixed
with the initialization commands. It's possible for the ioctl cmd to
be issued prior to the controller being enabled. To block this, the
ioctl admin commands need to be distinguished from admin commands used
for controller init. Added a USERCMD nvme_req(req)->rq_flags bit to
reflect this division and set it on ioctls requests. As the
nvmf_check_if_ready() routine is called prior to nvme_setup_cmd(),
ensure that commands allocated by the ioctl path (actually anything
in core.c) preps the nvme_req(req) before starting the io. This will
preserve the USERCMD flag during execution and/or retry.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.e>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
NVMe over Fabrics 1.0 Section 5.2 "Discovery Controller Properties and
Command Support" Figure 31 "Discovery Controller – Admin Commands"
explicitly listst all commands but "Get Log Page" and "Identify" as
reserved, but NetApp report the Linux host is sending Keep Alive
commands to the discovery controller, which is a violation of the
Spec.
We're already checking for discovery controllers when configuring the
keep alive timeout but when creating a discovery controller we're not
hard wiring the keep alive timeout to 0 and thus remain on
NVME_DEFAULT_KATO for the discovery controller.
This can be easily remproduced when issuing a direct connect to the
discovery susbsystem using:
'nvme connect [...] --nqn=nqn.2014-08.org.nvmexpress.discovery'
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 07bfcd09a2 ("nvme-fabrics: add a generic NVMe over Fabrics library")
Reported-by: Martin George <marting@netapp.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This removes a dependency on the order options are passed when creating
a fabrics controller. With the old code, if "nr_io_queues" appears before
an "nqn" option specifying the discovery controller, then nr_io_queues
is overridden with zero. If "nr_io_queues" appears after specifying the
discovery controller, then the nr_io_queues option is used to set the
number of queues, and the driver attempts to establish IO connections
to the discovery controller (which doesn't work).
It seems better to ignore (and warn about) the "nr_io_queues" option
if userspace has already asked to connect to the discovery controller.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
THIS_MODULE evaluates to NULL when used from code built into the kernel,
thus breaking built-in transport modules. Remove the bogus check.
Fixes: 0de5cd36 ("nvme-fabrics: protect against module unload during create_ctrl")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Pull block updates from Jens Axboe:
"This is the main pull request for block IO related changes for the
4.16 kernel. Nothing major in this pull request, but a good amount of
improvements and fixes all over the map. This contains:
- BFQ improvements, fixes, and cleanups from Angelo, Chiara, and
Paolo.
- Support for SMR zones for deadline and mq-deadline from Damien and
Christoph.
- Set of fixes for bcache by way of Michael Lyle, including fixes
from himself, Kent, Rui, Tang, and Coly.
- Series from Matias for lightnvm with fixes from Hans Holmberg,
Javier, and Matias. Mostly centered around pblk, and the removing
rrpc 1.2 in preparation for supporting 2.0.
- A couple of NVMe pull requests from Christoph. Nothing major in
here, just fixes and cleanups, and support for command tracing from
Johannes.
- Support for blk-throttle for tracking reads and writes separately.
From Joseph Qi. A few cleanups/fixes also for blk-throttle from
Weiping.
- Series from Mike Snitzer that enables dm to register its queue more
logically, something that's alwways been problematic on dm since
it's a stacked device.
- Series from Ming cleaning up some of the bio accessor use, in
preparation for supporting multipage bvecs.
- Various fixes from Ming closing up holes around queue mapping and
quiescing.
- BSD partition fix from Richard Narron, fixing a problem where we
can't mount newer (10/11) FreeBSD partitions.
- Series from Tejun reworking blk-mq timeout handling. The previous
scheme relied on atomic bits, but it had races where we would think
a request had timed out if it to reused at the wrong time.
- null_blk now supports faking timeouts, to enable us to better
exercise and test that functionality separately. From me.
- Kill the separate atomic poll bit in the request struct. After
this, we don't use the atomic bits on blk-mq anymore at all. From
me.
- sgl_alloc/free helpers from Bart.
- Heavily contended tag case scalability improvement from me.
- Various little fixes and cleanups from Arnd, Bart, Corentin,
Douglas, Eryu, Goldwyn, and myself"
* 'for-4.16/block' of git://git.kernel.dk/linux-block: (186 commits)
block: remove smart1,2.h
nvme: add tracepoint for nvme_complete_rq
nvme: add tracepoint for nvme_setup_cmd
nvme-pci: introduce RECONNECTING state to mark initializing procedure
nvme-rdma: remove redundant boolean for inline_data
nvme: don't free uuid pointer before printing it
nvme-pci: Suspend queues after deleting them
bsg: use pr_debug instead of hand crafted macros
blk-mq-debugfs: don't allow write on attributes with seq_operations set
nvme-pci: Fix queue double allocations
block: Set BIO_TRACE_COMPLETION on new bio during split
blk-throttle: use queue_is_rq_based
block: Remove kblockd_schedule_delayed_work{,_on}()
blk-mq: Avoid that blk_mq_delay_run_hw_queue() introduces unintended delays
blk-mq: Rename blk_mq_request_direct_issue() into blk_mq_request_issue_directly()
lib/scatterlist: Fix chaining support in sgl_alloc_order()
blk-throttle: track read and write request individually
block: add bdev_read_only() checks to common helpers
block: fail op_is_write() requests to read-only partitions
blk-throttle: export io_serviced_recursive, io_service_bytes_recursive
...
Commit df351ef737 ("nvme-fabrics: fix memory leak when parsing host ID
option") fixed the leak of 'p' but in case uuid_parse() fails the memory
is freed before the error print that is using it.
Free it after printing eventual errors.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: df351ef737 ("nvme-fabrics: fix memory leak when parsing host ID option")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We use match_strdup() to get a copy of the option string for host ID string, but
we just pass it to uuid_parse() and don't store the string pointer, so we need to
kfree() the string after parsing it.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
NVMe transport driver module unload may (and usually does) trigger
iteration over the active controllers and delete them all (sometimes
under a mutex). However, a controller can be created concurrently with
module unload which can lead to leakage of resources (most important char
device node leakage) in case the controller creation occured after the
unload delete and drain sequence. To protect against this, we take a
module reference to guarantee that the nvme transport driver is not
unloaded while creating a controller.
Signed-off-by: Roy Shterman <roys@lightbitslabs.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This adds a new nvme_subsystem structure so that we can track multiple
controllers that belong to a single subsystem. For now we only use it
to store the NQN, and to check that we don't have duplicate NQNs unless
the involved subsystems support multiple controllers.
Includes code originally from Hannes Reinecke to expose the subsystems
in sysfs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the ->delete_work and the associated helpers to common code instead
of duplicating them in every driver. This also adds the missing reference
get/put for the loop driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add the "duplicate_connect" boolean option (presence means true).
Default is false.
When false, the transport should validate whether a new controller request
is targeted for the same host transport addressing and target transport
addressing as an existing controller. If so, the new controller request
should be rejected.
When true, the callee is explicitly requesting a duplicate controller
connection to be made and the new request should be attempted.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Help userspace to make sure transport module is loaded.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently, driver code allows user to set 0 as KATO
(Keep Alive TimeOut), but this is not being respected.
This patch enforces the expected behavior.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The default host NQN, which is generated based on the host's UUID,
does not follow the UUID-based NQN format laid out in the NVMe 1.3
specification. Remove the "NVMf:" portion of the NQN to match the spec.
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
The mutex protects against the list of transports changing while a
controller is being created, but using a plain old mutex means that it
also serializes controller creation. This unnecessarily slows down
creating multiple controllers - for example for the RDMA transport,
creating a controller involves establishing one connection for every IO
queue, which involves even more network/software round trips, so the
delay can become significant.
The simplest way to fix this is to change the mutex to an rwsem and only
hold it for writing when the list is being mutated. Since we can take
the rwsem for reading while creating a controller, we can create multiple
controllers in parallel.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This helps users to quickly spot the reason of why connection fails
if the hostid is not compliant with the uuid format.
Signed-off-by: Guan Junxiong <guanjunxiong@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Only print the specified options that are not recognized, instead
of the whole list of options.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
NVMe 1.2.1 or later requires controllers to provide a subsystem NQN in the
Identify controller data structures. Use this NQN for the subsysnqn
sysfs attribute by storing it in the nvme_ctrl structure after verifying
it. For older controllers we generate a "fake" NQN per non-normative
text in the NVMe 1.3 spec.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No need to differentiate fabrics from pci/loop, also lower
it to 32 as we don't really need 256 inflight admin commands.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently we have no way to define a stable host-id but always use the one
which is randomly generated when we add the host or use the default host.
Provide a "hostid=%s" for user-space to pass in a persistent host-id which
overrides the randomly generated one.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To let the host know what happends to the connection establishment,
adjust the behavior of nvmf_log_connect_error to make more connect
specifig error codes human-readble.
Signed-off-by: Guan Junxiong <guanjunxiong@huawei.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
It is not a user option but rather a variable controller
attribute.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When a host sense that its controller session is damaged,
it tries to re-establish it periodically (reconnect every
reconnect_delay). It may very well be that the controller
is gone and never coming back, in this case the host will
try to reconnect forever.
Add a ctrl_loss_tmo to bound the number of reconnect attempts
to a specific controller (default to a reasonable 10 minutes).
The timeout configuration is actually translated into number of
reconnect attempts and not a schedule on its own but rather
divided with reconnect_delay. This is useful to prevent
racing flows of remove and reconnect, and it doesn't really
matter if we remove slightly sooner than what the user requested.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
nvmf_create_ctrl() relys on the presence of a create_crtl callback in the
registered nvmf_transport_ops, so make nvmf_register_transport require one.
Update the available call-sites as well to reflect these changes.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Adjust indentation such that arguments are aligned.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
This adds a shared per-request structure for all NVMe I/O. This structure
is embedded as the first member in all NVMe transport drivers request
private data and allows to implement common functionality between the
drivers.
The first use is to replace the current abuse of the SCSI command
passthrough fields in struct request for the NVMe command passthrough,
but it will grow a field more fields to allow implementing things
like common abort handlers in the future.
The passthrough commands are handled by having a pointer to the SQE
(struct nvme_command) in struct nvme_request, and the union of the
possible result fields, which had to be turned from an anonymous
into a named union for that purpose. This avoids having to pass
a reference to a full CQE around and thus makes checking the result
a lot more lightweight.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block layer updates from Jens Axboe:
"This is the main pull request for block layer changes in 4.9.
As mentioned at the last merge window, I've changed things up and now
do just one branch for core block layer changes, and driver changes.
This avoids dependencies between the two branches. Outside of this
main pull request, there are two topical branches coming as well.
This pull request contains:
- A set of fixes, and a conversion to blk-mq, of nbd. From Josef.
- Set of fixes and updates for lightnvm from Matias, Simon, and Arnd.
Followup dependency fix from Geert.
- General fixes from Bart, Baoyou, Guoqing, and Linus W.
- CFQ async write starvation fix from Glauber.
- Add supprot for delayed kick of the requeue list, from Mike.
- Pull out the scalable bitmap code from blk-mq-tag.c and make it
generally available under the name of sbitmap. Only blk-mq-tag uses
it for now, but the blk-mq scheduling bits will use it as well.
From Omar.
- bdev thaw error progagation from Pierre.
- Improve the blk polling statistics, and allow the user to clear
them. From Stephen.
- Set of minor cleanups from Christoph in block/blk-mq.
- Set of cleanups and optimizations from me for block/blk-mq.
- Various nvme/nvmet/nvmeof fixes from the various folks"
* 'for-4.9/block' of git://git.kernel.dk/linux-block: (54 commits)
fs/block_dev.c: return the right error in thaw_bdev()
nvme: Pass pointers, not dma addresses, to nvme_get/set_features()
nvme/scsi: Remove power management support
nvmet: Make dsm number of ranges zero based
nvmet: Use direct IO for writes
admin-cmd: Added smart-log command support.
nvme-fabrics: Add host_traddr options field to host infrastructure
nvme-fabrics: revise host transport option descriptions
nvme-fabrics: rework nvmf_get_address() for variable options
nbd: use BLK_MQ_F_BLOCKING
blkcg: Annotate blkg_hint correctly
cfq: fix starvation of asynchronous writes
blk-mq: add flag for drivers wanting blocking ->queue_rq()
blk-mq: remove non-blocking pass in blk_mq_map_request
blk-mq: get rid of manual run of queue with __blk_mq_run_hw_queue()
block: export bio_free_pages to other modules
lightnvm: propagate device_add() error code
lightnvm: expose device geometry through sysfs
lightnvm: control life of nvm_dev in driver
blk-mq: register device instead of disk
...
Add the host_traddr field to allow specification of the host-port
connection info for the transport. Will be used by FC transport.
Signed-off-by: James Smart <james.smart@broadcom.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Revise nvmf_get_address() string to account for not all options being
present.
Signed-off-by: James Smart <james.smart@broadcom.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Without this we'll get a use after free after connecting two controller
using the same hostnqn and then disconnecting one of them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jay Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
NVM Express 1.2.1 section 7.9, NVMe Qualified Names, specifies that the
UUID format of NQN uses a UUID based on RFC 4122.
RFC 4122 specifies that the UUID is encoded in big-endian byte order.
Switch the NVMe over Fabrics host ID field from little-endian UUID to
big-endian UUID to match the specification.
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Jay Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
