Introduce mt7615_mcu_fill_msg routine to initialize mcu messages.
mt7615_mcu_fill_msg will be reused adding mt7663u support
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/mediatek/mt76/mt76x0/phy.c: In function mt76x0_phy_rf_init:
drivers/net/wireless/mediatek/mt76/mt76x0/phy.c:1158:5: warning: variable val set but not used [-Wunused-but-set-variable]
Fixes: 10de7a8b4a ("mt76x0: phy files")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This if statement was supposed to be deleted, but it wasn't. It means
that we sometimes don't set the sensitivity correctly.
Fixes: 2cad515ece ("mt76: mt7615: add missing settings for simultaneous dual-band support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When injecting beacon frames via monitor interface, they must not be sent to
the beacon hardware queue, because they don't follow normal hardware beacon tx
rules.
Fix sending them by adding a flag to mt7615_mac_write_txwi that selects the
beacon queue for tx, and use it only from mt7615_mcu_set_bcn.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If the minimum power is raised too much, it can make it impossible for weaker
clients to connect, and there are some scenarios where the false detects will
not go down no matter how much the sensitivity is adjusted.
Fixes connectivity issues in some rare cases
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove usb workqueue if mt76u_set_endpoints fails.
Fixes: 284efb473e ("mt76: mt76u: rely on a dedicated stats workqueue")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Loop over all possible hw rx queues in mt76u_rx_tasklet since new
devices will report mcu events through mcu hw queue
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ath.git patches for v5.7. Major changes:
ath10k
* support for getting btcoex settings from Device Tree
* support QCA9377 SDIO device
ath11k
* add HE rate accounting
* add thermal sensor and cooling devices
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: b43-dev@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: b43-dev@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
hard_header_len provides limitations for things like AF_PACKET, such
that we don't allow transmitting packets smaller than this.
needed_headroom provides a suggested minimum headroom for SKBs, so that
we can trivally add our headers to the front.
The latter is the correct field to use in this case, while the former
mostly just prevents sending small AF_PACKET frames.
In any case, mwifiex already does its own bounce buffering [1] if we
don't have enough headroom, so hints (not hard limits) are all that are
needed.
This is the essentially the same bug (and fix) that brcmfmac had, fixed
in commit cb39288fd6 ("brcmfmac: use ndev->needed_headroom to reserve
additional header space").
[1] mwifiex_hard_start_xmit():
if (skb_headroom(skb) < MWIFIEX_MIN_DATA_HEADER_LEN) {
[...]
/* Insufficient skb headroom - allocate a new skb */
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <ganapathi.gbhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove unneeded variable ret used to store return value.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The simple_strtol() function is deprecated since it does not
check for the range overflow. Use kstrtoint() instead.
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove unused fab_version member from struct rtw_hal.
Some of the checks being made were nonsense.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware supports only STA as primary interface in repeater mode.
Since the only meaningful usage of AP + STA interface combination
is repeater, reject such combination with AP as primary interface.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Quantenna Pearl device exposes multiple (up to 3) radio interfaces under
single PCIe function. So far all the wiphy devices were attached to the
same pcie device. As a result, all different wireless network devices
were reported under the same sysfs directory for pcie device, e.g.:
$ ls /sys/class/net/wlan0/device/net/
wlan0 wlan1
It turns out that such behavior may confuse various users of wireless
subsystem. For instance, it turned out to be the case for:
- Linux init systems, e.g. for renaming based on parent device
- OpenWRT configuration scripts
Suggested solution is to add an intermediate virtual platform device
for each radio interface.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure that edmg field of cfg80211_chan_def structure is properly
initialized by zeros. Otherwise cfg80211_chandef_valid may return
false if edmg fields contain some garbage.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable WPA3 OWE support in AP mode. Driver currently supports cards that
offload OWE processing to userspace. This patch adds all the required
tools for such offloading. Firmware requests OWE processing sending new
UPDATE_OWE event to driver, which uses cfg80211_update_owe_info_event to
notify userspace software. After OWE processing is completed, userspace
sends calculated IEs to firmware using update_owe_info cfg80211 callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable WPA3 SAE support in AP mode. Driver currently supports cards
that offload SAE authentication to userspace. So allow userspace
software to subscribe and to send AUTH frames. Besides, enable
AP mode support in external_auth cfg80211 callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: ath11k@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When TPC is disabled IEEE80211_CONF_CHANGE_POWER event can be handled to
reconfigure HW's maximum txpower.
This fixes 0dBm txpower setting when user attaches to an interface for
the first time with the following scenario:
ieee80211_do_open()
ath9k_add_interface()
ath9k_set_txpower() /* Set TX power with not yet initialized
sc->hw->conf.power_level */
ieee80211_hw_config() /* Iniatilize sc->hw->conf.power_level and
raise IEEE80211_CONF_CHANGE_POWER */
ath9k_config() /* IEEE80211_CONF_CHANGE_POWER is ignored */
This issue can be reproduced with the following:
$ modprobe -r ath9k
$ modprobe ath9k
$ wpa_supplicant -i wlan0 -c /tmp/wpa.conf &
$ iw dev /* Here TX power is either 0 or 3 depending on RF chain */
$ killall wpa_supplicant
$ iw dev /* TX power goes back to calibrated value and subsequent
calls will be fine */
Fixes: 283dd11994 ("ath9k: add per-vif TX power capability")
Cc: stable@vger.kernel.org
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The CONFIG_ATH5K_AHB could be enabled on ATH25 system without enabling
ATH5K driver itself. This does not make sense because CONFIG_ATH5K_AHB
controls object build within drivers/net/wireless/ath/ath5k/ so enabling
it without CONFIG_ATH5K brings nothing.
Add proper dependency to CONFIG_ATH5K_AHB.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Temperature sensor generates electrical analog voltage from temperature
of each chain. The analog voltage is converted to digital value through
ADC. For reading temperature values fom user space, hw monitoring device
is used.
Whenever the user requests for current temperature, the driver sends WMI
command and wait for response. For reading temperature,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by suspending all data tx queues by given percentage of time. The
thermal device allows user to configure duty cycle.
Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder.
/sys/class/ieee80211/phy*/device/cooling_device.
To set duty cycle as 40%,
echo 40 >/sys/class/ieee80211/phy*/device/cooling_device/cur_state
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tid of 11a station with WMM disable reported by FW is 0x10 in
tx completion. The tid 16 is mapped to a NULL txq since buffer
MMPDU capbility is not supported. Then 11a station's airtime will
not be registered due to NULL txq check. As a results, airtime of
11a station keeps unchanged in debugfs system.
Mask the tid along with IEEE80211_QOS_CTL_TID_MASK to make it in
the valid range.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.10-00047
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently rx tid setup is happening for TID 0 and TID 16
during peer setup. And if other TID packets received for
the peer it will be redirected to rx error ring and not through
reo ring. And this rx tid configuration cannot be done
in the rx error ring path since it is a atomic context.
So moving the rx tid setup for all tids during the peer setup.
This is required to enable PN offload functionality to route
all packets through reo ring.
Co-developed-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before this change, after writing "warm_hw_reset" debugfs file, host
will send chip reset command to FW even though FW do not support this
service getting a warning print.
Though there is no FW impact before this change, this patch restricts
chip reset command sent to FW only if FW advertises the support via WMI
service bit.
Removed the redundant check and ath10k_warn() print as well.
New version FW will report chip reset service bit to host. Host allow user
to trigger WLAN chip reset only when fw report this service bit.
For older NON-TLV FW, since it do not report chip reset service bit, host
will not send chip reset command. For older TLV FW, since it report chip
reset service bit, host will send chip reset command.
Tested HW: QCA9984, WCN3990
QCA9984 FW version: WLAN.BL.3.9.0.2-00042-S-1
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When running simulate crash stress test, it happened
"failed to read from address 0x800: -110".
Test steps:
1. Run command continuous
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash
2. error happened and it did not begin recovery for long time.
[74377.334846] ath10k_sdio mmc1:0001:1: simulating soft firmware crash
[74378.378217] ath10k_sdio mmc1:0001:1: failed to read from address 0x800: -110
[74378.378371] ath10k_sdio mmc1:0001:1: failed to process pending SDIO interrupts: -110
It has sdio errors since it can not read MBOX_HOST_INT_STATUS_ADDRESS,
then it has to do recovery process to recovery ath10k.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add hardware parameters for QCA9377 sdio devices, it's now properly supported.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, OTP is downloaded twice in case of "pre-cal-dt"
and "pre-cal-file" to fetch the board ID and takes around
~2 sec more boot uptime.
First OTP download happens in "ath10k_core_probe_fw" and
second in ath10k_core_start. First boot does not need OTP
download in core start when valid board id acquired.
The second OTP download is required upon core stop/start.
This patch skips the OTP download when first OTP download
has acquired a valid board id. This patch also marks board
id invalid in "ath10k_core_stop", which will force the OTP
download in ath10k_core_start and fetches valid board id.
Tested HW: QCA9984
Tested FW: 10.4-3.6-00104
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of patches for v5.7. Lots of mt76 patches as they missed the
v5.6 deadline and hence they were postponed to the next version.
Otherwise nothing special standing out.
mt76
Major changes:
* dual-band concurrent support for MT7615
* fixes for rx path race conditions
* coverage class support for MT7615
* beacon fixes for USB devices
* MT7615 LED support
* set_antenna support for MT7615
* tracing improvements
* preparation for supporting new USB devices
* tx power fixes
brcmfmac
* support BRCM 4364 found in MacBook Pro 15,2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeYQnTAAoJEG4XJFUm622bVEkH/13OGWPYjWQXeAFeMFiukSp0
NJk9s6xRQmzuLxJsharKfwpr1hVm93ZZpGCG8RGCRAlMJqRnRT9q429YNFcpbWFY
NIfsioktIk7wbyXiw6p73z+vlvRgCYTQ/QCr19731xRli2JCNh9ZYzAOA6I6iX8v
7nCcRLLm4NM/+L+iybBumgNB4/5CCRgQTJQqbtvrgDQYXLMtu6HqcHQ1ldzivM9U
cs9c25tthC5Zv7YhAscVRDys4ca1o/gJr7VB6surTqLCx02LmgUjBZQ9ZFqabSBa
hkumUGivGkRN6yW1CDYu+Gok5ij0a/A3QQ9Hy5gAq1KrjtUKXbZeFVNSBSiKtQQ=
=kUdG
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-03-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.7
First set of patches for v5.7. Lots of mt76 patches as they missed the
v5.6 deadline and hence they were postponed to the next version.
Otherwise nothing special standing out.
mt76
Major changes:
* dual-band concurrent support for MT7615
* fixes for rx path race conditions
* coverage class support for MT7615
* beacon fixes for USB devices
* MT7615 LED support
* set_antenna support for MT7615
* tracing improvements
* preparation for supporting new USB devices
* tx power fixes
brcmfmac
* support BRCM 4364 found in MacBook Pro 15,2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* dual-band concurrent support for MT7615
* fixes for rx path race conditions
* EEPROM fixes
* MAC address handling fixes
* coverage class support for MT7615
* beacon fixes for USB devices
* MT7615 LED support
* minor cleanups/fixes for all drivers
* set_antenna support for MT7615
* tracing improvements
* preparation for supporting new USB devices
* tx power fixes
-----BEGIN PGP SIGNATURE-----
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAl5G3tEACgkQ130UHQKnbvXVtgCdEBlcmjViCqkCPXStdSxUy9o9
JCsAn2TnPduCoTCB1jo1foJbNXn5XzuG
=Z/l3
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2020-02-14' of https://github.com/nbd168/wireless
mt76 patches for 5.7
* dual-band concurrent support for MT7615
* fixes for rx path race conditions
* EEPROM fixes
* MAC address handling fixes
* coverage class support for MT7615
* beacon fixes for USB devices
* MT7615 LED support
* minor cleanups/fixes for all drivers
* set_antenna support for MT7615
* tracing improvements
* preparation for supporting new USB devices
* tx power fixes
Now that there is support for BIGTK configuration and AP/STA
functionality for using BIP with Beacon frames, indicate support for the
Beacon protection functionality.
Johannes: move this to hwsim, since it's not clear that all drivers
using mac80211 will do this correctly - lots of them modify the
beacon before transmission e.g. to update the TIM element, and that
would obviously break the signature.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200222132548.20835-7-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAl5GggsACgkQB8qZga/f
l8Qgdg//R42bSv94JYPcwZ5phgTgraCRZODWjBJq08n2T5m0EmEufgX79d9uEdgT
u9npvn+ich5/VZhmuSbGrW9TT6/FPLAZyghV1fj79o971Qd7ky2Mp8G1fcTEbtDn
IG2e9vauY9XDSb2O3wNj8dA8rAN/kLNmhsPqWxn2CgLPqjdbf+W15dvo4rnaL2gs
ffGyE47dHuAFwCruyT8UPbw3iu4+tQhruN9eVg+UkU8rJGvEMqfrLK20zl1weIV9
a7IuXdxacdsHO8Y+tl6GtvgOURQPpvf55+leLOUhcmHPJ3f/eAal6wmWRxDxs/qB
IWSe8BC81cZZ5pYWk1A+0sXfJMlYjNsN0xw5SQRSrbgyb5saz8aLUIlHsOBM4iPH
SwzCMN5A1GOPOUFsugzPwbiki9g6dh0/EC2NyXE4A26CAd967dVXTvTY5SMNgiB+
bZaaUDaPQUm1jgDT5bLRhTipTHbekDkYzG/e+wNO+HKyStoEYM485MwY4MQCYzEh
HKDmkAbFuCwEUeXXw1y8GybUknApCRru9FtY+oiN/+y/aESfB7HJfmDFFU/KYgPu
HOuqJoNAxdMdycDCb24/cLjUiehzfM6sujwBxZOD5WHhAcXrBo5dGd6ibfurIrjj
XI36/mwTiMtyyb0/5xM1AKvoic2j+a5YU3MB7KSc9TlaPa5j2NA=
=CgmJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As of 6-DEC-2019, NXP has acquired Marvell’s Wireless business
unit. This change is to update the license text accordingly.
Signed-off-by: James Cao <zheng.cao@nxp.com>
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce mt76_mcu data structure to contain common fields between
mt76u_mcu and mt76e_mcu.
Initialize mcu common fields in mt76_alloc_device().
Rely on mt76_mcu in mt76_mcu_rx_event and in mt76_mcu_get_response
in order to reuse them in usb code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get rid of rx_mask in mt7615_eeprom_parse_hw_cap routine since it is not
actually used
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rename usb stat_wq in wq in order to be reused not just for gathering hw
tx statistics
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
