Pull i2c updates from Wolfram Sang:
- API for late atomic transfers (e.g. to shut down via PMIC). We have a
seperate callback now which is called under clearly defined
conditions. In-kernel users are converted, too.
- new driver for the AMD PCIe MP2 I2C controller
- large refactoring for at91 and bcm-iproc (both gain slave support due
to this)
- and a good share of various driver improvements anf fixes
* 'i2c/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (57 commits)
dt-bindings: i2c: riic: document r7s9210 support
i2c: imx-lpi2c: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
i2c-piix4: Add Hygon Dhyana SMBus support
i2c: core: apply 'is_suspended' check for SMBus, too
i2c: core: ratelimit 'transfer when suspended' errors
i2c: iproc: Change driver to use 'BIT' macro
i2c: riic: Add Runtime PM support
i2c: mux: demux-pinctrl: use struct_size() in devm_kzalloc()
i2c: mux: pca954x: allow management of device idle state via sysfs
i2c: mux: pca9541: remove support for unused platform data
i2c: mux: pca954x: remove support for unused platform data
dt-bindings: i2c: i2c-mtk: add support for MT8516
i2c: axxia: use auto cmd for last message
i2c: gpio: flag atomic capability if possible
i2c: algo: bit: add flag to whitelist atomic transfers
i2c: stu300: use xfer_atomic callback to bail out early
i2c: ocores: enable atomic xfers
i2c: ocores: refactor setup for polling
i2c: tegra-bpmp: convert to use new atomic callbacks
i2c: omap: Add the master_xfer_atomic hook
...
Here is the big set of USB and PHY driver patches for 5.2-rc1
There is the usual set of:
- USB gadget updates
- PHY driver updates and additions
- USB serial driver updates and fixes
- typec updates and new chips supported
- mtu3 driver updates
- xhci driver updates
- other tiny driver updates
Nothing really interesting, just constant forward progress.
All of these have been in linux-next for a while with no reported
issues. The usb-gadget and usb-serial trees were merged a bit "late",
but both of them had been in linux-next before they got merged here last
Friday.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNKuwg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymRUgCfa8Ri7KrCaBR5NHQcLhbdrX90ToQAmgNw7vpo
fqt0XpNM0CSa9O/gOr79
=8HFh
-----END PGP SIGNATURE-----
Merge tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 5.2-rc1
There is the usual set of:
- USB gadget updates
- PHY driver updates and additions
- USB serial driver updates and fixes
- typec updates and new chips supported
- mtu3 driver updates
- xhci driver updates
- other tiny driver updates
Nothing really interesting, just constant forward progress.
All of these have been in linux-next for a while with no reported
issues. The usb-gadget and usb-serial trees were merged a bit "late",
but both of them had been in linux-next before they got merged here
last Friday"
* tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (206 commits)
USB: serial: f81232: implement break control
USB: serial: f81232: add high baud rate support
USB: serial: f81232: clear overrun flag
USB: serial: f81232: fix interrupt worker not stop
usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA
usb: dwc3: Fix default lpm_nyet_threshold value
usb: dwc3: debug: Print GET_STATUS(device) tracepoint
usb: dwc3: Do core validation early on probe
usb: dwc3: gadget: Set lpm_capable
usb: gadget: atmel: tie wake lock to running clock
usb: gadget: atmel: support USB suspend
usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask
dwc2: gadget: Fix completed transfer size calculation in DDMA
usb: dwc2: Set lpm mode parameters depend on HW configuration
usb: dwc2: Fix channel disable flow
usb: dwc2: Set actual frame number for completed ISOC transfer
usb: gadget: do not use __constant_cpu_to_le16
usb: dwc2: gadget: Increase descriptors count for ISOC's
usb: introduce usb_ep_type_string() function
usb: dwc3: move synchronize_irq() out of the spinlock protected block
...
Pull i2c fixes from Wolfram Sang:
"I2C driver bugfixes and a MAINTAINERS update for you"
* 'i2c/for-current-fixed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: Prevent runtime suspend of adapter when Host Notify is required
i2c: synquacer: fix enumeration of slave devices
MAINTAINERS: friendly takeover of i2c-gpio driver
i2c: designware: ratelimit 'transfer when suspended' errors
i2c: imx: correct the method of getting private data in notifier_call
We need this to make the usb-gadget branch merge cleaner. And for
testing to keep from hitting the same issues already fixed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use __maybe_unused for power management related functions
instead of #if CONFIG_PM_SLEEP to simply the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Hygon Dhyana CPU has the SMBus device with PCI device ID 0x790b,
which is the same as AMD CZ SMBus device. So add Hygon Dhyana support
to the i2c-piix4 driver by using the code path of AMD.
Signed-off-by: Pu Wen <puwen@hygon.cn>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We checked I2C calls, but not SMBus. Refactor the helper to an inline
function and use it for both, I2C and SMBus.
Fixes: 9ac6cb5fbb ("i2c: add suspended flag and accessors for i2c adapters")
Reported-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are two problems with WARN_ON() here. One: It is not ratelimited.
Two: We don't see which adapter was used when trying to transfer
something when already suspended. Implement a custom ratelimit once per
adapter and use dev_WARN there. This fixes both issues. Drawback is that
we don't see if multiple drivers are trying to transfer with the same
adapter while suspended. They need to be discovered one after the other
now. This is better than a high CPU load because a really broken driver
might try to resend endlessly.
Fixes: 9ac6cb5fbb ("i2c: add suspended flag and accessors for i2c adapters")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org # v5.1+
Mainly some pca954x work, i.e. removal of unused platform data support
and added support for sysfs interface for manipulating/examining the
idle state. And then a mechanical cocci-style patch.
Multiple users have reported their Synaptics touchpad has stopped
working between v4.20.1 and v4.20.2 when using SMBus interface.
The culprit for this appeared to be commit c5eb119007 ("PCI / PM: Allow
runtime PM without callback functions") that fixed the runtime PM for
i2c-i801 SMBus adapter. Those Synaptics touchpad are using i2c-i801
for SMBus communication and testing showed they are able to get back
working by preventing the runtime suspend of adapter.
Normally when i2c-i801 SMBus adapter transmits with the client it resumes
before operation and autosuspends after.
However, if client requires SMBus Host Notify protocol, what those
Synaptics touchpads do, then the host adapter must not go to runtime
suspend since then it cannot process incoming SMBus Host Notify commands
the client may send.
Fix this by keeping I2C/SMBus adapter active in case client requires
Host Notify.
Reported-by: Keijo Vaara <ferdasyn@rocketmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203297
Fixes: c5eb119007 ("PCI / PM: Allow runtime PM without callback functions")
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Keijo Vaara <ferdasyn@rocketmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C host driver for SynQuacer fails to populate the of_node and
ACPI companion fields of the struct i2c_adapter it instantiates,
resulting in enumeration of the subordinate I2C bus to fail.
Fixes: 0d676a6c43 ("i2c: add support for Socionext SynQuacer I2C controller")
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are two problems with dev_err() here. One: It is not ratelimited.
Two: We don't see which driver tried to transfer something with a
suspended adapter. Switch to dev_WARN_ONCE to fix both issues. Drawback
is that we don't see if multiple drivers are trying to transfer while
suspended. They need to be discovered one after the other now. This is
better than a high CPU load because a really broken driver might try to
resend endlessly.
Link: https://bugs.archlinux.org/task/62391
Fixes: 2751541555 ("i2c: designware: Do not allow i2c_dw_xfer() calls while suspended")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reported-by: skidnik <skidnik@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: skidnik <skidnik@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I'm not sure what made gcc warn about this code now. The 'ret' variable
does end up initialized in all cases, but it's definitely not obvious,
so the compiler is quite reasonable to warn about this.
So just add initialization to make it all much more obvious both to
compilers and to humans.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adding device property "ccgx,firmware-build" for the CCGx
device, so the CCGx driver knows which firmware binary to
use for a specific vendor.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the iProc I2C driver to use the 'BIT' macro from all '1 << XXX'
bit operations to get rid of compiler warning and improve readability of
the code
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
The behaviour, by default, to not deselect after each transfer is
unsafe when there is a device with an address that conflicts with
another device on another mux on the same parent bus, and it
may not be convenient to use devicetree to set the deselect mux,
e.g. when running on x86_64 when ACPI is used to discover most of the
device hierarchy.
Therefore, provide the ability to set the idle state behaviour using a
new sysfs file, idle_state as a complement to the method of
instantiating the device via sysfs. The possible behaviours are
disconnect, i.e. to deselect all channels from the mux, as-is (the
default), i.e. leave the last channel selected, and set a
predetermined channel.
The current behaviour of leaving the channel as-is after each
transaction is preserved.
Signed-off-by: Robert Shearman <robert.shearman@att.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
There are no in-tree users of the platform data, so remove it to
simplify the code slightly.
Remove the now unused pca954x.h platform data header.
Signed-off-by: Robert Shearman <robert.shearman@att.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
There are no in-tree users of the pca954x platform data and the
per-channel deselect configuration complicates efforts to export the
configuration to user-space in a way that could be applied to other
muxes. Therefore, remove support for the pca954x platform data.
Signed-off-by: Robert Shearman <robert.shearman@att.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Some recent commits to this driver were trying to make sure the TSS
interrupt is not generated on busy system due to 25ms timer expiring
between commands. It can still happen, however if STOP command is not
issued on time at the end of the transmission. If wait_for_completion in
axxia_i2c_xfer_msg() would not return after 25ms of getting an
interrupt, TSS will be generated and idev->err_msg will be set to
-ETIMEDOUT which will be returned from the axxia_i2c_xfer_msg(), even
though the transfer did actually succeed (STOP is automatically issued
when TSS triggers).
Fortunately, apart from already used manual and sequence commands, the
controller also has so called auto command. It works just like manual
mode but it but an automatic STOP is issued when either transfer length
is met or NAK is received from slave device.
This patch changes the axxia_i2c_xfer_msg() function so that auto
command is used for last message in transaction letting hardware manage
issuing STOP. TSS is disabled just after command transferring last
message finishes. Auto command, just like sequence, ends with SS
interrupt instead of SNS so handling of both had to be unified.
The axxia_i2c_stop() is no longer needed as the transfer can only end
with following conditions:
- fully successful - then last message was send by AUTO command and STOP
was issued automatically
- NAK received - STOP is issued automatically by controller
- arbitration lost - STOP should not be issued as we don't control the
bus
- IP interrupt received - this is sent when transfer length is set to 0
for auto/sequence command. The check for that is done before START is
send so no STOP is required
- TSS received between commands - STOP is issued by the controller
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If switching GPIOs does not sleep, then we can support atomic transfers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the new xfer_atomic callback to check a newly introduced flag to
whitelist atomic transfers. This will report configurations which
worked accidently.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the new callback to reject atomic transfers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver already has the routine in place, tie it to the new callback.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
By properly setting up the algorithm at probe time, we can skip the
check at every transfer. This allows us to get rid of the flags
completely.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver did handle this internally, convert it to use the new
callbacks.
Reviewed-by: Timo Alho <talho@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add the master_xfer_atomic hook to enable i2c transactions in irq
disabled contexts like the poweroff case.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
[wsa: simplified code a little: 'timeout = !ret']
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the parent has an atomic callback, we need to translate it the same
way as the non-atomic callback.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the parent adapter has atomic_xfer callbacks, populate them for the
mux adapter as well. We can use the same translation function as for the
non-atomic xfer callback.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We had the request to access devices very late when interrupts are not
available anymore multiple times now. Mostly to prepare shutdown or
reboot. Allow adapters to specify a specific callback for this case.
Note that we fall back to the generic {master|smbus}_xfer callback if
this new atomic one is not present. This is intentional to preserve the
previous behaviour and avoid regressions. Because there are drivers not
using interrupts or because it might have worked "accidently" before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Stefan Lengfeld <contact@stefanchrist.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If I2C transfers are executed in atomic contexts, trylock is used
instead of lock. This behaviour was missing for SMBUS, although a lot of
transfers are of SMBUS type, either emulated or direct. So, factor out
the locking routine into a helper and use it for I2C and SMBUS.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit cea443a81c ("i2c: Support i2c_transfer in atomic contexts")
added in_atomic() to the I2C core. However, the use of in_atomic()
outside of core kernel code is discouraged and was already[1] when this
code was added in early 2008. The above commit was a preparation for
commit b7a3670131 ("i2c-pxa: Add polling transfer"). Its commit
message says explicitly it was added "for cases where I2C transactions
have to occur at times interrup[t]s are disabled". So, the intention was
'disabled interrupts'. This matches the use cases for atomic I2C
transfers I have seen so far: very late communication (mostly to a PMIC)
to powerdown or reboot the system. For those cases, interrupts are
disabled then. It doesn't seem that in_atomic() adds value.
After a discussion with Peter Zijlstra[2], we came up with a better set
of conditionals to match the use case.
The I2C core will soon gain an extra callback into bus drivers
especially for atomic transfers to make them more generic. The code
deciding which transfer to use (atomic/non-atomic) should mimic the
behaviour which locking to use (trylock/lock). This is why we add a
helper for it.
[1] https://lwn.net/Articles/274695/
[2] http://patchwork.ozlabs.org/patch/1067437/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Stefan Lengfeld <contact@stefanchrist.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No further occurences in the driver.
Fixes: dd1aa2524b ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c compatible for MT8183. Compare to MT2712 i2c controller,
MT8183 has different register offsets. Ltiming_reg is added to
adjust low width of SCL. Arb clock and dma_sync are needed.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When i2c and apdma use different source clocks, we should enable
synchronization between them.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When two i2c controllers are internally connected to the same
GPIO pins, the arb clock is needed to ensure that the waveforms
do not interfere with each other. And we also need to enable
the interrupt to find arb lost, old i2c controllers also have
the bit.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
New i2c registers would have different offsets, so we use different
offsets array to distinguish different i2c registers version.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure to free the i2c adapter on the error exit path.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: e1ab9a468e ("i2c: imx: improve the error handling in i2c_imx_dma_request()")
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 54fb4a05af ("i2c: Check for ACPI resource conflicts") included
<linux/acpi.h> so we could use acpi_check_region(). Commit fd46a0064a
("i2c: convert i2c-isch to platform_device") removed the use of
acpi_check_region() but not the include.
Remove the now-unnecessary include of <linux/acpi.h>. No functional change
intended.
Fixes: fd46a0064a ("i2c: convert i2c-isch to platform_device")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
"res" can't be NULL because it's a pointer to somewhere in the middle of
the "adev" struct. Also probe() succeeded so there is no need to check
here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add NIC I2C support to the iProc I2C driver. Access to the NIC I2C base
registers requires going through the IDM wrapper to map into the NIC's
address space
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the following wrapper for read/write access of iProc i2c registers:
u32 iproc_i2c_rd_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
u32 offset)
void iproc_i2c_wr_reg(struct bcm_iproc_i2c_dev *iproc_i2c, u32 offset,
u32 val)
This preps the driver for support of indirect register access required
by certain SoCs with this iProc I2C block integrated
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add polling support to the iProc I2C driver. Polling mode is
activated when the driver fails to obtain an interrupt ID from device
tree
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for more master error status including FIFO underrun and RX
FIFO full
Signed-off-by: Michael Cheng <ccheng@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add slave mode support to the iProc I2C driver.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Michael Cheng <ccheng@broadcom.com>
Signed-off-by: Shreesha Rajashekar <shreesha.rajashekar@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support to allow I2C master read transfer up to 255 bytes.
Signed-off-by: Shreesha Rajashekar <shreesha@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of using custom variables and parser, convert the driver to use
the ones provided by I2C core.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
MP2 controllers have two separate busses, so may accommodate up to two I2C
adapters. Those adapters are listed in the ACPI namespace with the
"AMDI0011" HID, and probed by a platform driver.
Communication with the MP2 takes place through MMIO registers, or through
DMA for more than 32 bytes transfers.
This is major rework of the patch submitted by Nehal-bakulchandra Shah from
AMD (https://patchwork.kernel.org/patch/10597369/).
Most of the event handling of v3 was rewritten to make it work with more
than one bus (e.g on Ryzen-based Lenovo Yoga 530), and this version
contains many other improvements.
Signed-off-by: Elie Morisse <syniurge@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Slave mode driver is based on the concept of i2c-designware driver.
Signed-off-by: Juergen Fitschen <me@jue.yt>
[ludovic.desroches@microchip.com: rework Kconfig and replace IS_ENABLED
by defined]
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The single file i2c-at91.c has been split into core code (i2c-at91-core.c)
and master mode specific code (i2c-at91-master.c). This should enhance
maintainability and reduce ifdeffery for slave mode related code.
The code itself hasn't been touched. Shared functions only had to be made
non-static. Furthermore, includes have been cleaned up.
Signed-off-by: Juergen Fitschen <me@jue.yt>
[ludovic.desroches@microchip.com: fix checkpatch errors and use SPDX]
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In order to implement slave mode support for the at91 hardware we have to
segregate all master mode specific function parts from the general parts.
The upcoming slave mode patch will call its sepcific probe resp. init
function instead of the master mode functions after the shared general
code has been executed.
This concept has been influenced by the i2c-designware driver.
Signed-off-by: Juergen Fitschen <me@jue.yt>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When sending with DMA, the driver transfers the first byte with PIO (as
documented). However, it started DMA right after the first byte was
written. This worked, but was not according to the datasheet which
suggests to wait until data register was empty again. Implement this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We will need to know if enabling DMA was successful in a later patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use a macro for the hardcoded value and apply a build check. If it is
not met, the driver logic will not work anymore.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This avoids useless loops inside the I2C timing algorithm.
Actually, we support only one possible solution per prescaler value.
So after finding a solution with a prescaler, the algorithm can
switch directly to the next prescaler value.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Synopsys I2C Controller has an interface clock, but most SoCs hide
this away. However, on some SoCs you need to explicitly enable the
interface clock in order to access the registers. Therefore, add
support for an optional interface clock.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add PCI ID for Intel Comet Lake PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Before this commit the i2c-designware-platdrv assumes that if the pdev
has an apci-companion it should use a dynamic adapter-nr and it sets
adapter->nr to -1, otherwise it will use pdev->id as adapter->nr.
There are 3 ways how platform_device-s to which i2c-designware-platdrv
will bind can be instantiated:
1) Through of / devicetree
2) Through ACPI enumeration
3) Explicitly instantiated through platform_device_create + add
1) In case of devicetree-instantiation the drivers/of code always sets
pdev->id to PLATFORM_DEVID_NONE, which is -1 so in this case both paths
to set adapter->nr end up doing the same thing.
2) In case of ACPI instantiation the device will always have an
ACPI-companion, so we are already using dynamic adapter-nrs.
3) There are 2 places manually instantiating a designware_i2c platform_dev:
drivers/mfd/intel_quark_i2c_gpio.c
drivers/mfd/intel-lpss.c
In the intel_quark_i2c_gpio.c case pdev->id is always 0, so switching to
dynamic adapter-nrs here could lead to the bus-number no longer being
stable, but the quark X1000 only has 1 i2c-controller, which will also
be assigned bus-number 0 when using dynamic adapter-nrs.
In the intel-lpss.c case intel_lpss_probe() is called from either
intel-lpss-acpi.c in which case there always is an ACPI-companion, or
from intel-lpss-pci.c. In most cases devices handled by intel-lpss-pci.c
also have an ACPI-companion, so we use a dynamic adapter-nr. But in some
cases the ACPI-companion is missing and we would use pdev->id (allocated
from intel_lpss_devid_ida). Devices which use the intel-lpss-pci.c code
typically have many i2c busses, so using pdev->id in this case may lead
to a bus-number conflict, triggering a WARN(id < 0, "couldn't get idr")
in i2c-core-base.c causing an oops an the adapter registration to fail.
So in this case using non dynamic adapter-nrs is actually undesirable.
One machine on which this oops was triggering is the Apollo Lake based
Acer TravelMate Spin B118.
TL;DR: Switching to always using dynamic adapter-numbers does not make
any difference in most cases and in the one case where it does make a
difference the behavior change is desirable because the old behavior
caused an oops.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1687065
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c-designware-platdrv assumes that if the pdev has an apci-companion
it should use a dynamic adapter-nr and otherwise it will use pdev->id
as adapter-nr.
Before this commit the setting of the adapter.nr was somewhat convoluted,
in the acpi_companion case it was set from dw_i2c_acpi_configure, in the
non acpi_companion case it was set from dw_i2c_set_fifo_size based on
tx_fifo_depth not being set yet indicating that dw_i2c_acpi_configure was
not executed.
This cleans this up, directly setting the adapter-nr from
dw_i2c_plat_probe for both cases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure we report 'no buffer' for 0-length messages. This can only
happen if threshold is set to 0 which is kind of bogus but we should
still handle this situation. Update the docs and add a debug message
to educate callers of this function.
Reported-by: Hsin-Yi Wang <hsinyi@chromium.org>
Fixes: e94bc5d18b ("i2c: add helpers to ease DMA handling")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
To make sure people can understand the lockless design of this driver
without the need to dive into git history, add a comment giving an
overview of the situation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixes the problem that an interrupt may set up a new I2C
message and the DMA callback overwrites this setup.
By disabling the DMA Enable Register(ICDMAER), rcar_i2c_dma_unmap()
enables interrupts for register settings (such as Master Control
Register(ICMCR)) and advances the I2C transfer sequence.
If an interrupt occurs immediately after ICDMAER is disabled, the
callback handler later continues and overwrites the previous settings
from the interrupt. So, disable ICDMAER at the end of the callback to
ensure other interrupts are masked until then.
Note that this driver needs to work lock-free because there are IP cores
with a HW race condition which prevent us from using a spinlock in the
interrupt handler.
Reproduction test:
1. Add a delay after disabling ICDMAER. (It is expected to generate an
interrupt of rcar_i2c_irq())
void rcar_i2c_dma_unmap(struct rcar_i2c_priv *priv)
{
...
rcar_i2c_write(priv, ICDMAER, 0);
usleep_range(500, 800)
...
priv->dma_direction = DMA_NONE;
}
2. Execute DMA transfers
$ i2ctransfer -y 4 w9@0x6a 1 1+ r16
3. A log message of BUG_ON() will be displayed.
Fixes: 73e8b05283 ("i2c: rcar: add DMA support")
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: updated test case to be more reliable, added note to comment]
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When compiling with -Wformat, clang warns:
drivers/i2c/busses/i2c-sis630.c:482:4: warning: format specifies type
'unsigned short' but the argument has type 'int' [-Wformat]
smbus_base + SMB_STS,
^~~~~~~~~~~~~~~~~~~~
drivers/i2c/busses/i2c-sis630.c:483:4: warning: format specifies type
'unsigned short' but the argument has type 'int' [-Wformat]
smbus_base + SMB_STS + SIS630_SMB_IOREGION - 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/i2c/busses/i2c-sis630.c:531:37: warning: format specifies type
'unsigned short' but the argument has type 'int' [-Wformat]
"SMBus SIS630 adapter at %04hx", smbus_base + SMB_STS);
~~~~~ ^~~~~~~~~~~~~~~~~~~~
This patch fixes the format strings to use the format type for int.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Louis Taylor <louis@kragniz.eu>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DMA with zero-length transfers doesn't make sense and this HW doesn't
support them at all, so increase the threshold.
Fixes: fc66b39fe3 ("i2c: mediatek: Use DMA safe buffers for i2c transactions")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
[wsa: reworded commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAlyCpL0UHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vzoHw//ZyFbwekF0mV3RZwcV35LkScIOw0d
O1DgjJo8UbuV51+/foQeUZ8IzjHlybQhoFdJupPuw+LyaDUkwqjAmdtY8J/FjWSm
AJeVzu6gMF0Z9kwwGO4NyqX2EWluTD0xNLgf8g+fe3p1MtEuH6VCrqe+hk3wma0K
CrSIKWY/sO408SpAaWiLTEZmVT+hXiP9hJw1qTrbqKLtyWa4oCjErdoyUDsA01+5
gPndKC/3pu6q6q9Dd94582HuQaE2dKHWQXx6Fzd/tdCyYffpbOUAUNP3aRXaTKrS
MwKxOF3y7yUnz5RbxRgopwNVf5WyXhCnnPZRLaSxqnTSZCY6FCUi3l6RpVyWu2Ha
iztBbkTP/x6WV3VWg810qgQKQ9wl8oALMkoOfR6lWCR7MTuJnMXJtbrz0jWpEC2O
ZPwK9fAxFj2/3e13hx88O7Ek8kfajTPM8T15K79pvpljfqa0BD9SrhPyQ5ssmxj4
idz4yIFCATULKszPXA1QbfC1/xCDveQOEPSerL3eACXsLN17vfpOwOT9vWJm6bpr
6u5ggM2dEA07eI1ANnY6twn5g0kSYU9qISNQO98tA86IvaCnME0Z+k+SCwUNIM9U
ep9k0NdAGDNsYOfdVEEY0fYGT9k+9f9w8AfZLNvh0N3s7mGQQ35jf0Z75jj/jsor
cbMcPAN2jOCyFVs=
=vf9L
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
Pull i2c updates from Wolfram Sang:
- the I2C core gained helpers to assist drivers in handling their
suspended state, and drivers were converted to use it
- two new fault-injectors for stress-testing
- bigger refactoring and feature improvements for the ocores,
sh_mobile, and tegra drivers
- platform_data removal for the at24 EEPROM driver
- ... and various improvements and bugfixes all over the subsystem
* 'i2c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (69 commits)
i2c: Allow recovery of the initial IRQ by an I2C client device.
i2c: ocores: turn incomplete kdoc into a comment
i2c: designware: Do not allow i2c_dw_xfer() calls while suspended
i2c: tegra: Only display error messages if DMA setup fails
i2c: gpio: fault-injector: add 'inject_panic' injector
i2c: gpio: fault-injector: add 'lose_arbitration' injector
i2c: tegra: remove multi-master support
i2c: tegra: remove master fifo support on tegra186
i2c: tegra: change phrasing, "fallbacking" to "falling back"
i2c: expand minor range when registering chrdev region
i2c: aspeed: Add multi-master use case support
i2c: core-smbus: don't trace smbus_reply data on errors
i2c: ocores: Add support for bus clock via platform data
i2c: ocores: Add support for IO mapper registers.
i2c: ocores: checkpatch fixes
i2c: ocores: add SPDX tag
i2c: ocores: add polling interface
i2c: ocores: do not handle IRQ if IF is not set
i2c: ocores: stop transfer on timeout
i2c: tegra: add i2c interface timing support
...
A previous change allowed I2C client devices to discover new IRQs upon
reprobe by clearing the IRQ in i2c_device_remove. However, if an IRQ was
assigned in i2c_new_device, that information is lost.
For example, the touchscreen and trackpad devices on a Dell Inspiron laptop
are I2C devices whose IRQs are defined by ACPI extended IRQ types. The
client device structures are initialized during an ACPI walk. After
removing the i2c_hid device, modprobe fails.
This change caches the initial IRQ value in i2c_new_device and then resets
the client device IRQ to the initial value in i2c_device_remove.
Fixes: 6f108dd70d ("i2c: Clear client->irq in i2c_device_remove")
Signed-off-by: Jim Broadus <jbroadus@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
[wsa: this is an easy to backport fix for the regression. We will
refactor the code to handle irq assignments better in general.]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
gcc complains, rightfully so, I think:
drivers/i2c/busses/i2c-ocores.c:32: warning: Cannot understand * @process_lock: protect I2C transfer process.
on line 32 - I thought it was a doc line
Make it a simple comment.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On most Intel Bay- and Cherry-Trail systems the PMIC is connected over I2C
and the PMIC is accessed through various means by the _PS0 and _PS3 ACPI
methods (power on / off methods) of various devices.
This leads to suspend/resume ordering problems where a device may be
resumed and get its _PS0 method executed before the I2C controller is
resumed. On Cherry Trail this leads to errors like these:
i2c_designware 808622C1:06: controller timed out
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.P18W._ON, AE_ERROR
video LNXVIDEO:00: Failed to change power state to D0
But on Bay Trail this caused I2C reads to seem to succeed, but they end
up returning wrong data, which ends up getting written back by the typical
read-modify-write cycle done to turn on various power-resources.
Debugging the problems caused by this silent data corruption is quite
nasty. This commit adds a check which disallows i2c_dw_xfer() calls to
happen until the controller's resume method has completed.
Which turns the silent data corruption into getting these errors in
dmesg instead:
i2c_designware 80860F41:04: Error i2c_dw_xfer call while suspended
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.PCI0.GFX0._PS0, AE_ERROR
Which is much better.
Note the above errors are an example of issues which this patch will
help to debug, the actual fix requires fixing the suspend order and
this has been fixed by a different commit.
Note the setting / clearing of the suspended flag in the suspend / resume
methods is NOT protected by i2c_lock_bus(). This is intentional as these
methods get called from i2c_dw_xfer() (through pm_runtime_get/put) a nd
i2c_dw_xfer() is called with the i2c_bus_lock held, so otherwise we would
deadlock. This means that there is a theoretical race between a non runtime
suspend and the suspended check in i2c_dw_xfer(), this is not a problem
since normally we should not hit the race and this check is primarily a
debugging tool so hitting the check if there are suspend/resume ordering
problems does not need to be 100% reliable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 86c92b9965 ("i2c: tegra: Add DMA support") added DMA support
to the Tegra I2C driver for Tegra devices that support the APB DMA
controller. One side-effect of this change is that even for Tegra
devices that do not have an APB DMA controller and hence, cannot
support DMA tranfers for I2C transactions, the following error messages
are still displayed ...
ERR KERN tegra-i2c 31c0000.i2c: cannot use DMA: -19
ERR KERN tegra-i2c 31c0000.i2c: falling back to PIO
There is no point displaying the above messages for devices that do not
have an APB DMA controller and so fix this by returning from the
tegra_i2c_init_dma() function if 'has_apb_dma' is not true.
Furthermore, if CONFIG_TEGRA20_APB_DMA is not set, then rather than
printing an error message, print an debug message as for whatever reason
this could be intentional.
Fixes: 86c92b9965 ("i2c: tegra: Add DMA support")
Signed-off-by: Jonathan Hunter <jonathanh@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a fault injector simulating a Kernel panic happening after starting
a transfer. Read the docs for its usage.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a fault injector simulating 'arbitration lost' from multi-master
setups. Read the docs for its usage.
A helper function for future fault injectors using SCL interrupts is
created to achieve this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Multi-master support is defeatured on Tegra210 and Tegra186 due to
known bugs.
This patch removes multi-master support for Tegra210 and Tegra186
I2C HW feature.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra186 does not have master FIFO control register and instead
uses FIFO control register like prior Tegra chipset.
This patch fixes this and prevents crashing during boot when
accessing FIFO control registers.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The phrasing in two dev_err messages is using fallbacking which
os less understandable than "falling back", so fix this up.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Actually, total amount of available minor number for a single major is
MINORMASK + 1. So expand minor range when registering chrdev region.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
[wsa: fixed typo in commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In multi-master environment, this driver's master cannot know
exactly when a peer master sends data to this driver's slave so
cases can be happened that this master tries sending data through
the master_xfer function but slave data from a peer master is still
being processed or slave xfer is started by a peer immediately
after it queues a master command. To support multi-master use cases
properly, this H/W provides arbitration in physical level and it
provides priority based command handling too to avoid conflicts in
multi-master environment, means that if a master and a slave events
happen at the same time, H/W will handle a higher priority event
first and a pending event will be handled when bus comes back to
the idle state.
To support this H/W feature properly, this patch adds the 'pending'
state of master and its handling code so that the pending master
xfer can be continued after slave operation properly.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver's interrupt handler checks whether a message is currently
being handled with the curr_msg pointer. When it is NULL, the interrupt
is considered to be unexpected. Similarly, the i2c_start_transfer
routine checks for the remaining number of messages to handle in
num_msgs.
However, these values are never cleared and always keep the message and
number relevant to the latest transfer (which might be done already and
the underlying message memory might have been freed).
When an unexpected interrupt hits with the DONE bit set, the isr will
then try to access the flags field of the curr_msg structure, leading
to a fatal page fault.
The msg_buf and msg_buf_remaining fields are also never cleared at the
end of the transfer, which can lead to similar pitfalls.
Fix these issues by introducing a cleanup function and always calling
it after a transfer is finished.
Fixes: e247454103 ("i2c: bcm2835: Fix hang for writing messages larger than 16 bytes")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case the hold bit is not needed we are carrying the old values.
Fix the same by resetting the bit when not needed.
Fixes the sporadic i2c bus lockups on National Instruments
Zynq-based devices.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Reported-by: Kyle Roeschley <kyle.roeschley@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Tested-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If an smbus transfer fails, there's no guarantee that the output
buffer was written. So, avoid trying to show the output buffer when
tracing after an error. This was 'mostly harmless', but would trip
up kasan checking if left-over cruft in byte 0 is a large length,
causing us to read from unwritten memory.
Signed-off-by: John Sperbeck <jsperbeck@google.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add the I2C bus clock speed to the platform data structure.
If not set, default to 100KHz as before.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some implementations of the OCORES i2c bus master use IO mapped
registers. Add support for getting the IO registers from the platform
data, and register accessor functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Miscellaneous style fixes from checkpatch
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It adds the SPDX tag and it removes the old text about the GPLv2.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver assumes that an interrupt line is always available for
the I2C master. This is not always the case and this patch adds support
for a polling version.
Report from Andrew Lunn:
I did some timing tests for this. On my box, we request a udelay of
80uS. The kernel actually delays for about 79uS. We then spin in
ocores_wait() for an additional 10-11uS, which is 3 to 4 iterations.
There are actually 9 bits on the wire, not 8, since there is an
ACK/NACK bit after the actual data transfer. So i changed the delay to
(9 * 1000) / i2c->bus_clock_khz. That resulted in ocores_wait() mostly
not looping at all. But for reading an 4K AT24 EEPROM, it increased
the read time by 10ms, from 424ms to 434ms. So we should probably keep
with 8.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the Interrupt Flag (IF) is not set, we should not handle the IRQ:
- the line can be shared with other devices
- it can be a spurious interrupt
To avoid reading twice the status register, the ocores_process() function
expects it to be read by the caller.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Detecting a timeout is ok, but we also need to assert a STOP command on
the bus in order to prevent it from generating interrupts when there are
no on going transfers.
Example: very long transmission.
1. ocores_xfer: START a transfer
2. ocores_isr : handle byte by byte the transfer
3. ocores_xfer: goes in timeout [[bugfix here]]
4. ocores_xfer: return to I2C subsystem and to the I2C driver
5. I2C driver : it may clean up the i2c_msg memory
6. ocores_isr : receives another interrupt (pending bytes to be
transferred) but the i2c_msg memory is invalid now
So, since the transfer was too long, we have to detect the timeout and
STOP the transfer.
Another point is that we have a critical region here. When handling the
timeout condition we may have a running IRQ handler. For this reason I
introduce a spinlock.
In order to make easier to understan locking I have:
- added a new function to handle timeout
- modified the current ocores_process() function in order to be protected
by the new spinlock
Like this it is obvious at first sight that this locking serializes
the execution of ocores_process() and ocores_process_timeout()
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds I2C interface timing registers support for
proper bus rate configuration along with meeting the I2C spec
setup and hold times based on the tuning performed on Tegra210,
Tegra186 and Tegra194 platforms.
I2C_INTERFACE_TIMING_0 register contains TLOW and THIGH field
and Tegra I2C controller design uses them as a part of internal
clock divisor.
I2C_INTERFACE_TIMING_1 register contains the setup and hold times
for start and stop conditions.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra194 allows max of 64K bytes and Tegra186 and prior allows
max of 4K bytes of transfer per packet.
one sec timeout is not enough for transfers more than 10K bytes
at STD bus rate.
This patch updates I2C transfer timeout based on the transfer size
and I2C bus rate to allow enough time during max transfer size at
lower bus speed.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds DMA support for Tegra I2C.
Tegra I2C TX and RX FIFO depth is 8 words. PIO mode is used for
transfer size of the max FIFO depth and DMA mode is used for
transfer size higher than max FIFO depth to save CPU overhead.
PIO mode needs full intervention of CPU to fill or empty FIFO's
and also need to service multiple data requests interrupt for the
same transaction. This adds delay between data bytes of the same
transfer when CPU is fully loaded and some slave devices has
internal timeout for no bus activity and stops transaction to
avoid bus hang. DMA mode is helpful in such cases.
DMA mode is also helpful for Large transfers during downloading or
uploading FW over I2C to some external devices.
Tegra210 and prior Tegra chips use APBDMA driver which is replaced
with GPCDMA on Tegra186 and Tegra194.
This patch uses has_apb_dma flag in hw_feature to differentiate
DMA driver change between Tegra chipset.
APBDMA driver is registered from module-init level and this patch
also has a change to register I2C driver at module-init level
rather than subsys-init to avoid deferring I2C probe till APBDMA
driver is registered.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra194 supports maximum 64K bytes per packet including 12 bytes of
packet header irrespective of PIO or DMA mode transfer.
This patch updates Tegra194 max write length to account for packet
header size for transfers.
Cc: stable@vger.kernel.org # 4.20+
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra186 and prior supports maximum 4K bytes per packet transfer
including 12 bytes of packet header.
This patch fixes max write length limit to account packet header
size for transfers.
Cc: stable@vger.kernel.org # 4.4+
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Bus clear feature of Tegra I2C controller helps to recover from
bus hang when I2C master loses the bus arbitration due to the
slave device holding SDA LOW continuously for some unknown reasons.
Per I2C specification, the device that held the bus LOW should
release it within 9 clock pulses.
During bus clear operation, Tegra I2C controller sends 9 clock
pulses and terminates the transaction with STOP condition.
Upon successful bus clear operation, bus goes to idle state and
driver retries the transaction.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch sorts all the include headers alphabetically for the
I2C Tegra driver.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The latest documentation made it clear that we need to initialize the
TCYC value independently of DMA. The old code used TCYC06 (wrongly) for
non-DMA transfers. The new code sets TCYC up independently from DMA.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I think it is clear enough if we have the explanation once and make it
clear it is applicable for both SCL and SDA. Reword it a little with
the help of Simon's native language skills :)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We measured the clock on a Lager and an Ebisu board. The new formula
gives better results for both. So after Gen3, switch to this formula for
all Gen2 SoCs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We could finally measure the clock on an Ebisu board. The new formula
gives way better results, i.e. 100kHz instead of 106kHz and 400kHz
instead of 387kHz. Switch to these formulas for all Gen3 SoCs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Makes it easier to add new ones.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This augments the CBUS GPIO I2C driver to use GPIO
descriptors for clock, sel and data. We drop the platform
data that was only used for carrying GPIO numbers and
use machine descriptor tables instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update copyright years and remove a comment which grew incorrect and
useless over time.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no value in chronological sorting. Make it easier to follow for
humans.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Completion_done() is useless when we don't use its return value,
so we remove it.
Signed-off-by: qii wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Different speeds have been defined by macros,
so we use macros definitions.
Signed-off-by: qii wang <qii.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Less risk for duplications when adding new ones.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And use kernel style for the remaining comments in the header.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This adds device tree probing support for the IOP3xx
I2C master.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If an I2C adapter doesn't match the provided device tree node, also try
matching the parent's device tree node. This allows finding an adapter
based on the device node of the parent device that was used to register
it.
This fixes a regression on Tegra124-based Chromebooks (Nyan) where the
eDP controller registers an I2C adapter that is used to read to EDID.
After commit 993a815dcb ("dt-bindings: panel: Add missing .txt
suffix") this stopped working because the I2C adapter could no longer
be found. The approach in this patch fixes the regression without
introducing the issues that the above commit solved.
Fixes: 17ab7806de ("drm: don't link DP aux i2c adapter to the hardware device node")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We currently get the following error with pixcir_ts driver during a
suspend resume cycle:
omap_i2c 4802a000.i2c: controller timed out
pixcir_ts 1-005c: pixcir_int_enable: can't read reg 0x34 : -110
pixcir_ts 1-005c: Failed to disable interrupt generation: -110
pixcir_ts 1-005c: Failed to stop
dpm_run_callback(): pixcir_i2c_ts_resume+0x0/0x98
[pixcir_i2c_ts] returns -110
PM: Device 1-005c failed to resume: error -110
And at least am437x based devices with pixcir_ts will fail to resume
to a touchscreen that is configured as the wakeup-source in device
tree for these devices.
This is because pixcir_ts tries to reconfigure it's registers for
noirq suspend which fails. This also leaves i2c-omap in enabled state
for suspend.
Let's fix the pixcir_ts issue and make sure i2c-omap is suspended by
adding SET_NOIRQ_SYSTEM_SLEEP_PM_OPS.
Let's also get rid of some ifdefs while at it and replace them with
__maybe_unused as SET_RUNTIME_PM_OPS and SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
already deal with the various PM Kconfig options.
Reported-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move the Rohm Vendor ID to pci_ids.h instead of defining it in several
drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This commit removes hard-coded bus timeout value setting so that
it can be set by i2c-core-base.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update copyright years and add Renesas to it. Add/update comments to
make driver easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the do_while loop which was just there to have an easy exit with
"break;" and replace it with if-else-blocks which should make the state
machine clearer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In preparation to remove the do-while-loop.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All state machines deal with pd->pos values. This helper function is an
exception and makes it only more confusing.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is clear that we always send the address in TX_FIRST and data in TX.
No need to pass it from the caller.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It makes the code much easier comprehensible to explicitly code that the
first byte will be client address and all the following bytes are the
actual data.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
pd->pos won't be smaller than -1, so we can simplify the logic.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When doing s2idle/s2ram on Salvator-X(S):
WARNING: CPU: 2 PID: 971 at drivers/i2c/i2c-core-base.c:1869 __i2c_transfer+0x608/0x910
[...]
Call trace:
__i2c_transfer+0x608/0x910
i2c_smbus_xfer_emulated+0x158/0x5b0
__i2c_smbus_xfer+0x17c/0x818
i2c_smbus_xfer+0x64/0x98
i2c_smbus_read_byte_data+0x40/0x70
cs2000_bset.isra.1+0x2c/0x68
__cs2000_set_rate.constprop.7+0x80/0x148
cs2000_resume+0x18/0x20
dpm_run_callback+0x74/0x330
device_resume_early+0xd4/0x120
dpm_resume_early+0x158/0x4f8
suspend_devices_and_enter+0x36c/0xd98
[...]
On second resume, the sound driver fails with:
cs2000-cp 2-004f: pll lock failed
rcar_sound ec500000.sound: can't use clk 1
As the CS2000 clock driver needs to send I2C messages during suspend,
the I2C controller driver should be suspended later, and resumed
earlier. Fix this by using the noirq sleep ops instead of the normal
sleep ops, which are called after the late sleep ops, as used by the
CS2000 clock driver.
Fixes: 18569fa89a ("i2c: rcar: add suspend/resume support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Change the call to PTR_ERR to access the value just tested by IS_ERR.
Fixes: 5b3a23a3cc ("i2c: imx: notify about real errors on dma i2c_imx_dma_request")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Improve the error handling in i2c_imx_dma_request() and let it return an error
indication that the caller then can handle accordingly.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At least on i.MX5x, the DMA events for I2C and SDHC use the same channel
and there can only be a single user. So in this case there should be no
message emitted that looks like an error if the I2C device doesn't have
an assigned DMA channel. In contrast real problems that were only
emitted at debug level before should be described at a higher level
to be better visible and so understandable.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra194 supports maximum 64K Bytes transfer per packet.
Tegra186 and prior supports maximum 4K Bytes transfer per packet.
This patch fixes this payload difference between Tegra194 and prior
Tegra chipsets using separate i2c_adapter_quirks.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If adapter->retries is set to a minus value from user space via ioctl,
it will make __i2c_transfer and __i2c_smbus_xfer skip the calling to
adapter->algo->master_xfer and adapter->algo->smbus_xfer that is
registered by the underlying bus drivers, and return value 0 to all the
callers. The bus driver will never be accessed anymore by all users,
besides, the users may still get successful return value without any
error or information log print out.
If adapter->timeout is set to minus value from user space via ioctl,
it will make the retrying loop in __i2c_transfer and __i2c_smbus_xfer
always break after the the first try, due to the time_after always
returns true.
Signed-off-by: Yi Zeng <yizeng@asrmicro.com>
[wsa: minor grammar updates to commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Because the adapter will be set up before every transaction anyhow, we
just need to mark it as suspended to the I2C core.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rejecting transfers should be handled by the core. Also, this will
ensure proper locking which was forgotten in this open coded version.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rejecting transfers should be handled by the core. Also, this will
ensure proper locking which was forgotten in this open coded version.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rejecting transfers should be handled by the core.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The pointer to a device is usually named 'dev'. These 'pdev' here look
much like copy&paste errors. Fix them to avoid confusion.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rejecting transfers should be handled by the core. Also, this will
ensure proper locking which was forgotten in this open coded version
and make sure resume mark is set after enabling clocks (not before).
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rejecting transfers should be handled by the core.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This flag was defined and checked but never set a value. Remove it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
A few drivers open code the handling of suspended adapters. It could be
handled by the core, though, to ensure generic handling. This patch adds
the flag and accessor functions. The usage of these helpers is optional,
though. See the kerneldoc in this patch. Using the new flag, we now
reject further transfers if the adapter is already marked suspended.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"I2C has only driver updates for you this time.
Mostly new IDs/DT compatibles, also SPDX conversions, small cleanups.
STM32F7 got FastMode+ and PM support, Axxia some reliabilty
improvements"
* 'i2c/for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (26 commits)
i2c: Add Actions Semiconductor Owl family S700 I2C support
dt-bindings: i2c: Add S700 support for Actions Semi Soc's
i2c: ismt: Add support for Intel Cedar Fork
i2c: tegra: Switch to SPDX identifier
i2c: tegra: Add missing kerneldoc for some fields
i2c: tegra: Cleanup kerneldoc comments
i2c: axxia: support sequence command mode
dt-bindings: i2c: rcar: Add r8a774c0 support
dt-bindings: i2c: sh_mobile: Add r8a774c0 support
i2c: sh_mobile: Add support for r8a774c0 (RZ/G2E)
i2c: i2c-cros-ec-tunnel: Switch to SPDX identifier.
i2c: powermac: Use of_node_name_eq for node name comparisons
i2c-axxia: check for error conditions first
i2c-axxia: dedicated function to set client addr
dt-bindings: i2c: Use correct vendor prefix for Atmel
i2c: tegra: replace spin_lock_irqsave with spin_lock in ISR
eeprom: at24: add support for 24c2048
dt-bindings: eeprom: at24: add "atmel,24c2048" compatible string
i2c: i2c-stm32f7: add PM Runtime support
i2c: sh_mobile: add support for r8a77990 (R-Car E3)
...
Add S700 to the list of devices supported by Owl I2C driver.
Add Actions Semiconductor Owl family S700 I2C driver.
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add PCI ID for the Intel Cedar Fork iSMT SMBus controller.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
[wsa: kept sorting]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=r3Fl
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig updates from Masahiro Yamada:
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
* tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (39 commits)
kconfig: surround dbg_sym_flags with #ifdef DEBUG to fix gconf warning
kconfig: split images.c out of qconf.cc/gconf.c to fix gconf warnings
kconfig: add static qualifiers to fix gconf warnings
kconfig: split the lexer out of zconf.y
kconfig: split some C files out of zconf.y
kconfig: convert to SPDX License Identifier
kconfig: remove keyword lookup table entirely
kconfig: update current_pos in the second lexer
kconfig: switch to ASSIGN_VAL state in the second lexer
kconfig: stop associating kconf_id with yylval
kconfig: refactor end token rules
kconfig: stop supporting '.' and '/' in unquoted words
treewide: surround Kconfig file paths with double quotes
microblaze: surround string default in Kconfig with double quotes
kconfig: use T_WORD instead of T_VARIABLE for variables
kconfig: use specific tokens instead of T_ASSIGN for assignments
kconfig: refactor scanning and parsing "option" properties
kconfig: use distinct tokens for type and default properties
kconfig: remove redundant token defines
kconfig: rename depends_list to comment_option_list
...
The USB Power Delivery discrete components now can be enumerated by
i2c-multi-instantiate driver via several resources under single ACPI
device node (ACPI ID is INT3515).
Touchscreen support is added for the Mediacom Flexbook Edge 11.
Mellanox driver got fixed due to updates in their firmware.
The power management stub driver for AtomISP v2 is fixed in order to support
Intel Baytrail SoCs where same quirk is needed for S0ix to work.
Special key handling has been fixed for Favorites hotkey on Thinkpad, and
Screen LOCK on ASUS.
Ideapad Yoga 2 13 has no HW rfkill switch, thus, driver has been updated
to support this.
Few cleanups related to debugfs have been made in Intel IPS and
Intel PMC drivers. Besides that Intel PMC has been extended
to show more detailed information about Latency Tolerance.
The following is an automated git shortlog grouped by driver:
ACPI / scan:
- Create platform device for INT3515 ACPI nodes
Add the VLV ISP PCI ID to atomisp2_pm:
- Add the VLV ISP PCI ID to atomisp2_pm
asus-nb-wmi:
- Drop mapping of 0x33 and 0x34 scan codes
- Map 0x35 to KEY_SCREENLOCK
asus-wmi:
- Tell the EC the OS will handle the display off hotkey
dell-laptop:
- Mark expected switch fall-throughs
Documentation/ABI:
- Add new attribute for mlxreg-io sysfs interfaces
Fix config space access for intel_atomisp2_pm:
- Fix config space access for intel_atomisp2_pm
i2c:
- acpi: Introduce i2c_acpi_get_i2c_resource() helper
- acpi: Use ACPI_FAILURE instead of !ACPI_SUCCESS
- acpi: Return error pointers from i2c_acpi_new_device()
i2c-multi-instantiate:
- Allow to have same slaves
- Introduce IOAPIC IRQ support
- Distinguish IRQ resource type
- Count I2cSerialBus() resources
- Get rid of obsolete conditional
- Defer probe when no adapter found
- Accept errors of i2c_acpi_new_device()
ideapad-laptop:
- Add Yoga 2 13 to no_hw_rfkill list
iio:
- inv_mpu6050: Use i2c_acpi_get_i2c_resource() helper
intel_cht_int33fe:
- Get rid of obsolete conditional
- Accept errors of i2c_acpi_new_device()
- Remove duplicate NULL check
intel_ips:
- Convert to use DEFINE_SHOW_ATTRIBUTE macro
- Remove never happen condition
- NULL check before some freeing functions is not needed
- remove unnecessary checks in ips_debugfs_init
intel_pmc_core:
- convert to DEFINE_SHOW_ATTRIBUTE
- Decode Snoop / Non Snoop LTR
- Fix LTR IGNORE Max offset
- Show Latency Tolerance info
intel_telemetry:
- convert to DEFINE_SHOW_ATTRIBUTE
mlx-platform:
- Convert to use SPDX identifier
- Allow mlxreg-io driver activation for new systems
- Fix LED configuration
- Fix tachometer registers
- Rename new systems product names
- Add definitions for new registers
thinkpad_acpi:
- Cleanup quirks macros
- Change the keymap for Favorites hotkey
touchscreen_dmi:
- Add info for the Mediacom Flexbook Edge 11
-----BEGIN PGP SIGNATURE-----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=kYH6
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.21-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- The USB Power Delivery discrete components now can be enumerated by
i2c-multi-instantiate driver via several resources under single ACPI
device node (ACPI ID is INT3515).
- Touchscreen support is added for the Mediacom Flexbook Edge 11.
- Mellanox driver got fixed due to updates in their firmware.
- The power management stub driver for AtomISP v2 is fixed in order to
support Intel Baytrail SoCs where same quirk is needed for S0ix to
work.
- Special key handling has been fixed for Favorites hotkey on Thinkpad,
and Screen LOCK on ASUS.
- Ideapad Yoga 2 13 has no HW rfkill switch, thus, driver has been
updated to support this.
- Few cleanups related to debugfs have been made in Intel IPS and Intel
PMC drivers. Besides that Intel PMC has been extended to show more
detailed information about Latency Tolerance
* tag 'platform-drivers-x86-v4.21-1' of git://git.infradead.org/linux-platform-drivers-x86: (41 commits)
platform/x86: mlx-platform: Convert to use SPDX identifier
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform/x86: mlx-platform: Allow mlxreg-io driver activation for new systems
platform/x86: mlx-platform: Fix LED configuration
platform/x86: mlx-platform: Fix tachometer registers
platform/x86: mlx-platform: Rename new systems product names
platform/x86: mlx-platform: Add definitions for new registers
platform/x86: intel_telemetry: convert to DEFINE_SHOW_ATTRIBUTE
platform/x86: intel_pmc_core: convert to DEFINE_SHOW_ATTRIBUTE
platform/x86: thinkpad_acpi: Cleanup quirks macros
platform/x86: touchscreen_dmi: Add info for the Mediacom Flexbook Edge 11
platform/x86: Fix config space access for intel_atomisp2_pm
platform/x86: Add the VLV ISP PCI ID to atomisp2_pm
platform/x86: intel_ips: Convert to use DEFINE_SHOW_ATTRIBUTE macro
platform/x86: intel_ips: Remove never happen condition
platform/x86: intel_ips: NULL check before some freeing functions is not needed
platform/x86: intel_ips: remove unnecessary checks in ips_debugfs_init
iio: inv_mpu6050: Use i2c_acpi_get_i2c_resource() helper
ACPI / scan: Create platform device for INT3515 ACPI nodes
platform/x86: i2c-multi-instantiate: Allow to have same slaves
...
The Kconfig lexer supports special characters such as '.' and '/' in
the parameter context. In my understanding, the reason is just to
support bare file paths in the source statement.
I do not see a good reason to complicate Kconfig for the room of
ambiguity.
The majority of code already surrounds file paths with double quotes,
and it makes sense since file paths are constant string literals.
Make it treewide consistent now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Not all fields were properly documented. Add kerneldoc for the missing
fields to prevent the build from flagging them.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some of the kerneldoc uses a strange spelling for abbreviations. Turn
them into all-uppercase and clean up some whitespace issues while at it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In order to comply with SMBus specification, the Axxia I²C module will
abort the multi message transfer if the delay between finishing sending
one message and starting another is longer than 25ms. Unfortunately it
isn't that hard to trigger this situation on a busy system. In order to
fix this problem, we should make sure hardware does whole transaction
without waiting for software to fill some data.
Fortunately, in addition to Manual mode that is currently used by the
driver to perform I²C transfers, the module supports also so called
Sequence mode. In this mode, the module automatically performs
predefined sequence of operations - it sends a slave address, transmits
specified number of bytes from the FIFO, changes transfer direction,
resends the slave address and then reads specified number of bytes to
FIFO. While very inflexible, this does fit a most common case of multi
message transfer - the one where you first write a register number you
want to read and then read it.
To use this mode effectively, a number of conditions must be met to
ensure the transaction does fit the predefined sequence. In case this is
not the case, a fallback to manual mode is used.
The initialization of this mode is very similar to Manual mode. The most
notable difference is different bit in the Master Interrupt Status
designating finishing of transaction. Also some of the errors, like TSS,
cannot happen in this mode.
While it is possible to support transactions requesting a read of any
size (RFL interrupt will be generated when FIFO size is not enough) the
TFL interrupt is not available in this mode, thus the write part of the
transaction cannot exceed FIFO_SIZE (8).
Note that in case of a NAK during transaction, the NA/ND status bits
will be set before STOP command is generated, triggering an interrupt
while the controller is still busy. Current solution for this problem is
to actively wait for this command to stop before leaving xfer callback.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
[wsa: added braces around else branch spotted by checkpatch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Similarly to R-Car E3, RZ/G2E doesn't come with automatic
transmission registers, as such it is not considered compatible
with the existing fallback bindings.
Add SoC specific binding compatibility to allow for later
support for automatic transmission.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When CONFIG_PM is disabled, this is needed to avoid a harmless
unused-function warning:
drivers/i2c/busses/i2c-nvidia-gpu.c:345:12: error: 'gpu_i2c_resume' defined but not used [-Werror=unused-function]
Fixes: c71bcdcb42 ("i2c: add i2c bus driver for NVIDIA GPU")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
