The current set minimum voltage of 730000µV seems to be wrong. I don't
know the document which specifies that but the imx6qdl datasheets says
that the minimum voltage should be 0.925V for VDD_ARM (LDO bypassed,
lowest opp) and 1.15V for VDD_SOC (LDO bypassed, lowest opp).
Fixes: ddec5d1c00 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The sram-node compatible properties have mistakingly combined the
model-specific string with the generic "mtd-ram" string.
Note that neither "cy7c1019dv33-10zsxi, mtd-ram" or
"cy7c1019dv33-10zsxi" are used by any in-kernel driver and they are
not present in any binding.
The physmap driver will however bind to platform devices that specify
"mtd-ram".
Fixes: fc48e76489 ("ARM: dts: imx6: Add support for Toradex Colibri iMX6 module")
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The difference between "fsl,etsec2-mdio" and "gianfar" has to do with
the .get_tbipa function, which calculates the address of the TBIPA
register automatically, if not explicitly specified. [ see
drivers/net/ethernet/freescale/fsl_pq_mdio.c ]. On LS1021A, the TBIPA
register is at offset 0x30 within the port register block, which is what
the "gianfar" method of calculating addresses actually does.
Luckily, the bad "compatible" is inconsequential for ls1021a.dtsi,
because the TBIPA register is explicitly specified via the second "reg"
(<0x0 0x2d10030 0x0 0x4>), so the "get_tbipa" function is dead code.
Nonetheless it's good to restore it to its correct value.
Background discussion:
https://www.spinics.net/lists/stable/msg361156.html
Fixes: c7861adbe3 ("ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per i.MX7D Document Number: IMX7DCEC Rev. 6, 03/2019,
there are only consumer/industrial parts, and 1.2GHz
is only support in consumer parts.
So exclude automotive from 792/996MHz/1.2GHz and exclude
industrial from 1.2GHz.
Fixes: d7bfba7296 ("ARM: dts: imx7d: Update cpufreq OPP table")
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the vmmc is supplied by the 1.8V pmic rail but this is wrong.
The default module behaviour is to power VCCQ and VCC by the 3.3V power
rail. Optional the user can connect the VCCQ to the pmic 1.8V emmc
power rail using a solder jumper.
Fixes: ddec5d1c00 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is some material that we picked up into our tree late, or that had
more complex dependencies on more than one topic branch that makes sense
to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to better
reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards
-----BEGIN PGP SIGNATURE-----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=R7GU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Olof Johansson:
"This is some material that we picked up into our tree late, or that
had more complex dependencies on more than one topic branch that makes
sense to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to
better reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: OMAP2+: Drop legacy platform data for omap4 des
ARM: OMAP2+: Drop legacy platform data for omap4 sham
ARM: OMAP2+: Drop legacy platform data for omap4 aes
...
the normal collection of driver updates to support new SoCs, fix incorrect
data, and convert various drivers to clk_hw based APIs.
In the core, we allow clk_ops::init() to return an error code now so that we
can fail clk registration if the callback does something like fail to allocate
memory. We also add a new "terminate" clk_op so that things done in
clk_ops::init() can be undone, e.g. free memory. We also spit out a warning now
when critical clks fail to enable and we support changing clk rates and
enable/disable state through debugfs when developers compile the kernel
themselves.
On the driver front, we get support for what seems like a lot of Qualcomm and
NXP SoCs given that those vendors dominate the diffstat. There are a couple new
drivers for Xilinx and Amlogic SoCs too. The updates are all small things like
fixing the way glitch free muxes switch parents, avoiding div-by-zero problems,
or fixing data like parent names. See the updates section below for more
details.
Finally, the "basic" clk types have been converted to support specifying
parents with clk_hw pointers. This work includes an overhaul of the fixed-rate
clk type to be more modern by using clk_hw APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting
-----BEGIN PGP SIGNATURE-----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=UjXu
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There are a few changes to the core framework this time around, in
addition to the normal collection of driver updates to support new
SoCs, fix incorrect data, and convert various drivers to clk_hw based
APIs.
In the core, we allow clk_ops::init() to return an error code now so
that we can fail clk registration if the callback does something like
fail to allocate memory. We also add a new "terminate" clk_op so that
things done in clk_ops::init() can be undone, e.g. free memory. We
also spit out a warning now when critical clks fail to enable and we
support changing clk rates and enable/disable state through debugfs
when developers compile the kernel themselves.
On the driver front, we get support for what seems like a lot of
Qualcomm and NXP SoCs given that those vendors dominate the diffstat.
There are a couple new drivers for Xilinx and Amlogic SoCs too. The
updates are all small things like fixing the way glitch free muxes
switch parents, avoiding div-by-zero problems, or fixing data like
parent names. See the updates section below for more details.
Finally, the "basic" clk types have been converted to support
specifying parents with clk_hw pointers. This work includes an
overhaul of the fixed-rate clk type to be more modern by using clk_hw
APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw
based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config
symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M
SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (140 commits)
dt/bindings: clk: fsl,plldig: Drop 'bindings' from schema id
clk: ls1028a: Fix warning on clamp() usage
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
...
Here is the big USB and Thunderbolt and PHY driver updates for 5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code has
begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFTNw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynpKQCgrh2FoobS2x0oFg/OUHdjokQV/BYAoJGWLOmt
8S5cnsCuLq3w5qpCcBva
=PMGd
-----END PGP SIGNATURE-----
Merge tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
This enables thermal for the BCM2711 (used on Raspberry Pi 4) by adding
the AVS monitor and a subnode for the thermal part.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1578941778-23321-4-git-send-email-stefan.wahren@i2se.com
This series of changes mostly configures the cameras for dra7 and
am437x that have been pending for few months now because of waiting
for clock dependencies to clear. So these changes are based on earlier
dts changes with with Tero Kristo's for-5.6-ti-clk branch merged in.
Then there's a series of changes to configure powervr sgx target module
for am335x, am437x and dra7 that have been waiting to have the rstctrl
reset driver dependencies to clear.
Also included are few minor patches to configure 1-wire and coulomb
counter calibration interrupt for droid4.
-----BEGIN PGP SIGNATURE-----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=u4PK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.6/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
Late omap dts changes for v5.6 merge window
This series of changes mostly configures the cameras for dra7 and
am437x that have been pending for few months now because of waiting
for clock dependencies to clear. So these changes are based on earlier
dts changes with with Tero Kristo's for-5.6-ti-clk branch merged in.
Then there's a series of changes to configure powervr sgx target module
for am335x, am437x and dra7 that have been waiting to have the rstctrl
reset driver dependencies to clear.
Also included are few minor patches to configure 1-wire and coulomb
counter calibration interrupt for droid4.
* tag 'omap-for-v5.6/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: dts: Add omap3-echo
ARM: dts: Add dtsi files for AM3703, AM3715 and DM3725
ARM: dts: am335x-icev2: Add support for OSD9616P0899-10 at i2c0
...
Link: https://lore.kernel.org/r/pull-1579896427-50330@atomide.com-3
Signed-off-by: Olof Johansson <olof@lixom.net>
The Kconfig stage (arch/Kconfig) has already evaluated whether the
compiler supports -fno-stack-protector.
You can use CONFIG_CC_HAS_STACKPROTECTOR_NONE instead of invoking
the compiler to check the flag here.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This reverts commit e17b1af96b, which is
no longer necessary now that the v7 specific routines take care not to
issue CP15 barrier instructions before they are enabled in SCTLR.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Commit e17b1af96b
"ARM: 8857/1: efi: enable CP15 DMB instructions before cleaning the cache"
added some explicit handling of the CP15BEN bit in the SCTLR system
register, to ensure that CP15 barrier instructions are enabled, even
if we enter the decompressor via the EFI stub.
However, as it turns out, there are other ways in which we may end up
using CP15 barrier instructions without them being enabled. I.e., when
the decompressor startup code skips the cache_on() initially, we end
up calling cache_clean_flush() with the caches and MMU off, in which
case the CP15BEN bit in SCTLR may not be programmed either. And in
fact, cache_on() itself issues CP15 barrier instructions before actually
enabling them by programming the new SCTLR value (and issuing an ISB)
Since these routines are shared between v7 CPUs and older ones that
implement the CPUID extension as well, using the ordinary v7 barrier
instructions in this code is not possible, and so we should enable the
CP15 ones explicitly before issuing them. Note that a v7 ISB is still
required between programming the SCTLR register and using the CP15 barrier
instructions, and we should take care to branch over it if the CP15BEN
bit is already set, given that in that case, the CPU may not support it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Looks like we have wrong default memory size for beaglebone black,
it has at least 512 MB of RAM and not 256 MB. This causes an issue
when booted with GRUB2 that does not seem to pass memory info to
the kernel.
And for am43x-epos-evm the SPI pin directions need to be configured
for SPI to work.
-----BEGIN PGP SIGNATURE-----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=XXZc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-fixes-whenever-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few minor fixes for omaps
Looks like we have wrong default memory size for beaglebone black,
it has at least 512 MB of RAM and not 256 MB. This causes an issue
when booted with GRUB2 that does not seem to pass memory info to
the kernel.
And for am43x-epos-evm the SPI pin directions need to be configured
for SPI to work.
* tag 'omap-for-fixes-whenever-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1
ARM: dts: am335x-boneblack-common: fix memory size
Link: https://lore.kernel.org/r/pull-1579895109-287828@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
With "[PATCHv3] w1: omap-hdq: Simplify driver with PM runtime autosuspend"
we can read the droid4 battery information over 1-wire with this patch
with something like:
# modprobe omap_hdq
# hd /sys/bus/w1/devices/89-*/89-*/nvmem
...
Unfortunately the format of the battery data seems to be Motorola specific
and is currently unusable for battery charger unless somebody figures out
what it means.
Note that currently keeping omap_hdq module loaded will cause extra power
consumption as it seems to scan devices periodically.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We added coulomb counter calibration support With commit 0cb90f071f
("power: supply: cpcap-battery: Add basic coulomb counter calibrate
support"), but we also need to configure the related interrupt.
Without the interrupt calibration happens based on a timeout after two
seconds, with the interrupt the calibration just gets done a bit faster.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This seems to be similar to what we have for am335x. The following can be
tested via sysfs with the to ensure the SGX module gets enabled and disabled
properly:
# echo on > /sys/bus/platform/devices/5600fe00.target-module/power/control
# rwmem 0x5600fe00 # revision register
0x5600fe00 = 0x40000000
# echo auto > /sys/bus/platform/devices/5600fe00.target-module/power/control
# rwmem 0x5000fe00
Bus error
Note that this patch depends on the PRM rstctrl driver that has
been recently posted. If the child device driver(s) need to prevent
rstctrl reset on PM runtime suspend, the drivers need to increase
the usecount for the shared rstctrl reset that can be mapped also
for the child device(s) or accessed via dev->parent.
Cc: Adam Ford <aford173@gmail.com>
Cc: Filip Matijević <filip.matijevic.pz@gmail.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: moaz korena <moaz@korena.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Philipp Rossak <embed3d@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I've tested that the interconnect target module enables and idles
just fine when probed with ti-sysc with PM runtime control via sys:
# echo on > $(find /sys -name control | grep \/5600)
# rwmem 0x5600fe00 # OCP Revision
0x5600fe00 = 0x40000000
# echo auto > $(find /sys -name control | grep \/5600)
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The following can be tested via sysfs with the following to ensure the SGX
module gets enabled and disabled properly:
# echo on > /sys/bus/platform/devices/5600fe00.target-module/power/control
# rwmem 0x5600fe00 # revision register
0x5600fe00 = 0x40000000
# echo auto > /sys/bus/platform/devices/5600fe00.target-module/power/control
# rwmem 0x5000fe00
Bus error
Note that this patch depends on the PRM rstctrl driver that has
been recently posted. If the child device driver(s) need to prevent
rstctrl reset on PM runtime suspend, the drivers need to increase
the usecount for the shared rstctrl reset that can be mapped also
for the child device(s) or accessed via dev->parent.
Cc: Adam Ford <aford173@gmail.com>
Cc: Filip Matijević <filip.matijevic.pz@gmail.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: moaz korena <moaz@korena.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Philipp Rossak <embed3d@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add VPE node as a child of l4 interconnect in order for it to probe
using ti-sysc.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clkctrl nodes for VPE module.
Note that because of the current dts node name dependency for mapping to
clock domain, we must still use "vpe-clkctrl@" naming instead of generic
"clock@" naming for the node. And because of this, it's probably best to
apply the dts node addition together along with the other clock changes.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add VPFE device nodes entries.
Add OmniVision OV2659 sensor device nodes and linkage.
Since Rev1.2a on this board the sensor source clock (xvclk) has a
dedicated 12Mhz oscillator instead of using clkout1.
Add 'audio_mstrclk' fixed clock object to represent it.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add VPFE device nodes entries.
Add OmniVision OV2659 sensor device nodes and linkage.
The sensor clock (xvclk) is sourced from clkout1.
Add clock entries to properly select clkout1 and set its parent
clock to sys_clkin_ck.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
clkout1 clock node and its generation tree was missing. Add this based
on the data on TRM and PRCM functional spec.
commit 664ae1ab25 ("ARM: dts: am43xx: add clkctrl nodes") effectively
reverted this commit 8010f13a40 ("ARM: dts: am43xx: add support for
clkout1 clock") which is needed for the ov2659 camera sensor clock
definition hence it is being re-applied here.
Note that because of the current dts node name dependency for mapping to
clock domain, we must still use "clkout1-*ck" naming instead of generic
"clock@" naming for the node. And because of this, it's probably best to
apply the dts node addition together along with the other clock changes.
Fixes: 664ae1ab25 ("ARM: dts: am43xx: add clkctrl nodes")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device nodes for CSI2 camera board OV5640.
Add the CAL port nodes with the necessary linkage to the ov5640 nodes.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the required dtsi node to support the Camera
Adaptation Layer (CAL) for the DRA76 family of devices.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device nodes for CSI2 camera board OV5640.
Add the CAL port nodes with the necessary linkage to the ov5640 nodes.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the required dtsi node to support the Camera
Adaptation Layer (CAL) for the DRA72 family of devices.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add CAM nodes as a child of l4 interconnect in order for it to probe
using ti-sysc.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clkctrl nodes for CAM domain.
Note that because of the current dts node name dependency for mapping to
clock domain, we must still use "cam-clkctrl@" naming instead of generic
"clock@" naming for the node. And because of this, it's probably best to
apply the dts node addition together along with the other clock changes.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is similar to dra7 and omap4 with different clock naming
and module address.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add RNG interconnect data for omap4 similar to what dra7 has. The
clock is OMAP4_CM_L4SEC_RNG_CLKCTRL_OFFSET at offset address 0x01c0,
which matches what dra7 also has with DRA7_L4SEC_CLKCTRL_INDEX(0x1c0).
Note that we need to also add the related l4_secure clock entries.
I've only added RNG, the others can be added as they get tested.
They are probably very similar to what we already have for dra7
in dra7_l4sec_clkctrl_regs[].
With the clock tagged CLKF_SOC_NONSEC, clock is set disabled for secure
devices and clk_get() will fail. Additionally we disable the RNG target
module on droid4 to avoid introducing new boot time warnings.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The secure clocks on omap5 are similar to what we already have for dra7
with dra7_l4sec_clkctrl_regs and documented in the omap5432 TRM in
"Table 3-1044. CORE_CM_CORE Registers Mapping Summary".
The secure clocks are part of the l4per clock manager. As the l4per
clock manager has now two clock domains as children, let's also update
the l4per clockdomain node name to follow the "clock" node naming with
a domain specific compatible property.
Compared to omap4, omap5 has more clocks working in hardare autogating
mode.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The secure clocks on omap4 are similar to what we already have for dra7
in dra7_l4sec_clkctrl_regs and documented in the omap4460 TRM "Table
3-1346 L4PER_CM2 Registers Mapping Summary".
The secure clocks are part of the l4_per clock manager. As the l4_per
clock manager has now two clock domains as children, let's also update
the l4_per clockdomain node name to follow the "clock" node naming with
a domain specific compatible property.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Set d0 and d1 pin directions for spi0 and spi1 as per their pinmux.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is similar to what we have for omap5 except the gpu_cm address is
different, the mux clocks have one more source option, and there's no
divider clock.
Note that because of the current dts node name dependency for mapping to
clock domain, we must still use "gpu-clkctrl@" naming instead of generic
"clock@" naming for the node. And because of this, it's probably best to
apply the dts node addition together along with the other clock changes.
For accessing the GPU, we also need to configure the interconnect target
module for GPU similar to what we have for omap5, I'll send that change
separately.
Cc: Benoit Parrot <bparrot@ti.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
