Enet needs to get configration parameter by acpi. This patch
adds support of ACPI for enet. The configuration parameter will
be configed in BIOS.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The miscellaneous operation is implemented in BIOS, the kernel can call
_DSM method help to call the implementation in ACPI case. Here is a patch
to do that.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ACPI case, there is no interface to register phy device to mdio-bus.
Phy device has to be registered itself to mdio-bus, and then enet can
get the phy device's info so that it can config the phy-device to help
to trasmit and receive data.
HNS hardware topology is as below. The MDIO controller may control several
PHY-devices, and each PHY-device connects to a MAC device. PHY-devices
will register when each mac find PHY device in initial sequence.
cpu
|
|
-------------------------------------------
| | |
| | |
| dsaf |
MDIO | MDIO
| --------------------------- |
| | | | | |
| | | | | |
| MAC MAC MAC MAC |
| | | | | |
---- |-------- |-------- | | --------
|| || || ||
PHY PHY PHY PHY
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dsaf needs to get configuration parameter by ACPI, so this patch add
support of ACPI.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The misc operation for different hw platform may be different, if using
current implementation, it will add a new branch on each function for
every new hw platform, so we add a method for this operation.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As device_node is only used by DT case, HNS needs to treat the other
cases including ACPI. It needs to use uniform ways to handle both of
DT and ACPI. This patch chooses phy_device, and of_phy_connect and
of_phy_attach are only used by DT case. It needs to use uniform interface
to handle that sequence by both DT and ACPI.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As device_node is only used by DT case, it is expected to find uniform
ways. So fwnode_handle is the suitable method.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As irq_of_parse_and_map is only used by DT case, it is excepted to use
a uniform interface. So it is used platform_get_irq() instead.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OF series functions can be used only for DT case. Use unified
device property function instead to support both DT and ACPI.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns-mdio needs to register itself to mii-bus. The info of the device can
be read by both DT and ACPI.
HNS tries to call Linux PHY driver to help access PHY-devices, the HNS
hardware topology is as below. The MDIO controller may control several
PHY-devices, and each PHY-device connects to a MAC device. The MDIO will
be registered to mdiobus, then PHY-devices will register when each mac
find PHY device.
cpu
|
|
-------------------------------------------
| | |
| | |
| dsaf |
MDIO | MDIO
| --------------------------- |
| | | | | |
| | | | | |
| MAC MAC MAC MAC |
| | | | | |
---- |-------- |-------- | | --------
|| || || ||
PHY PHY PHY PHY
And the driver can handle reset sequence by _RST method in DSDT in ACPI
case.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hns-mdio only supports DT case now. do some cleanup to prepare
for introducing other cases later, no functional change.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the statement
assert(priv || priv->ae_handle);
the right side of || is only evaluated if priv is null.
v2:
As suggested by David Leight and David Miller the assert
statements are removed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indexes should generally be avoided. So we use reg rather than port-id to
index ports.
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because cpld-ctrl-reg property is offset base on cpld-syscon property,
we make it as a cell in the cpld-syscon property.
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port mode offset for each dsaf port is different. The current code is not
so readability. This patch adds configuration named port-mode-offset to
make the code simple and more readability. If port-mode-offset isn't
exists, default value 0 will be used.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset offset for each port in a dsaf is different. The current code is
not so readability. This patch adds configuration named port-rst-offset to
make the code simple and more readability. If this attribute doesn't exist,
default value of this attribute is equal to its port index.
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds attribute cpld_ctrl for dsaf port node, parses the syscon
for mac_cb from dts, and changes the method of access the cpld related
registers through syscon.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two kinds of dsaf device in hns, one is for service ports,
contains crossbar in it, can work under different mode. Another is for
debug port, only can work under "single-port" mode. The current code only
declared a dsaf device for both service ports and debug ports. This patch
separate it to three platform devices.
Here is the diagram of all port in one platform device(old):
CPU
|
| DSAF(one platform device)
-------------------------------------------------------------- /
| | | | | /
| PPE PPE PPE | /
| | | | | /
| | | | | /
| crossbar | | | /
| | | | |/
| ----------------------------------- | | |
| | | | | | | | | |
| | | | | | | | | |
| MAC MAC MAC MAC MAC MAC MAC MAC |
| | | | | | | | | |
--------------------------------------------------------------
| | | | | | | |
PHY PHY PHY PHY PHY PHY PHY PHY
Here is the diagram of separate all ports to three platform(new):
CPU
|
-----------------------------------
| | |
---------------------------------------------- --------- ---------
| | | | | | | |
| PPE | | PPE | | PPE |
| | | | | | | | |
| | | | | | | | |
| crossbar | | | | | | |
| | | | | | | | |
| ---------------------------------- | | | | | | |
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| MAC MAC MAC MAC MAC MAC | | MAC | | MAC |
| | | | | | | | | | | | | |
---------------------------------------------- --------- ---------
| | | | | | \ / | / |
PHY PHY PHY PHY PHY PHY \ / PHY / PHY
\ / /
\ / /
DSAF(three platform device)
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tunes the header file by the alphabetical order.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the read/write function for dsaf to
access the registers through syscon methods.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the subctrl reset offset for dsaf, this property is used to reset
xge/ge ports for different dsaf. If this attribute is not present,
default value 0 will be used.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch parse port-idx-in-ae in enet node. In NIC mode of DSAF, all 6
PHYs of service DSAF are taken as ethernet ports to the CPU. The
port-idx-in-ae can be 0 to 5. Here is the diagram:
+-----+---------------+
| CPU |
+-+-+-+---+-+-+-+-+-+-+
| | | | | | | |
debug debug service
port port port
(0) (0) (0-5)
In Switch mode of DSAF, all 6 PHYs of service DSAF are taken as physical
ports connect to a LAN Switch while the CPU side assume itself have one
single NIC connect to this switch. In this case, the port-idx-in-ae will
be 0 only.
+-----+-----+------+------+
| CPU |
+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | service| port(0)
debug debug +------------+
port port | switch |
(0) (0) +-+-+-+-+-+-++
| | | | | |
external port
when port-idx-in-ae is not exists, old attribute port-id will be used
(only for compatible purpose, not recommended to use port-id in new code).
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As debug ports are moved from service dsaf to debug dsaf,
the interrupts offset should start from 0, So this patch
re-defines the offset index of debug ports.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new dsaf mode named "single-port" mode for debug port.
This mode only contains one debug port. This patch also changes the
method of distinguishing the port type.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds support of pause ctrl for HNS V2, and this feature is lost
by HNS V1:
1) service ports can disable rx pause frame,
2) debug ports can open tx/rx pause frame.
And this patch updates the REGs about the pause ctrl when updated
status function called by upper layer routine.
Signed-off-by: Lisheng <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Missing device reference in IPSEC input path results in crashes
during device unregistration. From Subash Abhinov Kasiviswanathan.
2) Per-queue ISR register writes not being done properly in macb
driver, from Cyrille Pitchen.
3) Stats accounting bugs in bcmgenet, from Patri Gynther.
4) Lightweight tunnel's TTL and TOS were swapped in netlink dumps, from
Quentin Armitage.
5) SXGBE driver has off-by-one in probe error paths, from Rasmus
Villemoes.
6) Fix race in save/swap/delete options in netfilter ipset, from
Vishwanath Pai.
7) Ageing time of bridge not set properly when not operating over a
switchdev device. Fix from Haishuang Yan.
8) Fix GRO regression wrt nested FOU/GUE based tunnels, from Alexander
Duyck.
9) IPV6 UDP code bumps wrong stats, from Eric Dumazet.
10) FEC driver should only access registers that actually exist on the
given chipset, fix from Fabio Estevam.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
net: mvneta: fix changing MTU when using per-cpu processing
stmmac: fix MDIO settings
Revert "stmmac: Fix 'eth0: No PHY found' regression"
stmmac: fix TX normal DESC
net: mvneta: use cache_line_size() to get cacheline size
net: mvpp2: use cache_line_size() to get cacheline size
net: mvpp2: fix maybe-uninitialized warning
tun, bpf: fix suspicious RCU usage in tun_{attach, detach}_filter
net: usb: cdc_ncm: adding Telit LE910 V2 mobile broadband card
rtnl: fix msg size calculation in if_nlmsg_size()
fec: Do not access unexisting register in Coldfire
net: mvneta: replace MVNETA_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
net: mvpp2: replace MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
net: dsa: mv88e6xxx: Clear the PDOWN bit on setup
net: dsa: mv88e6xxx: Introduce _mv88e6xxx_phy_page_{read, write}
bpf: make padding in bpf_tunnel_key explicit
ipv6: udp: fix UDP_MIB_IGNOREDMULTI updates
bnxt_en: Fix ethtool -a reporting.
bnxt_en: Fix typo in bnxt_hwrm_set_pause_common().
bnxt_en: Implement proper firmware message padding.
...
It may fail to set coalesce usecs to HW, and Ethtool needs to know if it
is successful to cfg the parameter or not. So it needs return the errno by
dsaf.ko.
Signed-off-by: Lisheng <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The overtime setting and getting REGs in HNS V2 is defferent from HNS V1.
It needs to be distinguished between them if getting or setting the REGs.
Signed-off-by: Lisheng <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are only three patches this time, most other changes to
files in include/asm-generic tend to go through the tree of whoever
depends on the change.
Two patches are cleanups for stuff that is no longer needed,
the main change is to adapt the generic version of BUG_ON()
for CONFIG_BUG=n to make it behave consistently with BUG().
This avoids undefined behavior along with a number of warnings
about that undefined behavior in randconfig builds when
we keep going on after hitting a BUG_ON().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8tPL
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are only three patches this time, most other changes to files in
include/asm-generic tend to go through the tree of whoever depends on
the change.
Two patches are cleanups for stuff that is no longer needed, the main
change is to adapt the generic version of BUG_ON() for CONFIG_BUG=n to
make it behave consistently with BUG().
This avoids undefined behavior along with a number of warnings about
that undefined behavior in randconfig builds when we keep going on
after hitting a BUG_ON()"
* tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: remove old nonatomic-io wrapper files
asm-generic: default BUG_ON(x) to if(x)BUG()
asm-generic: page.h: Remove useless get_user_page and free_user_page
The hilink status reg in HNS V2 is different from HNS v1. In HNS V2, It
distinguishes differnt lane status according to the bit-field of the reg.
As is shown below:
[0:0] ---> lane0
[1:1] ---> lane1
...
But the current driver reads the reg to get the hilink status ONLY
concidering HNS V1 situation. Here is a patch to support both of them.
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a misuse of PTR as shown below:
ae_node = (void *)of_parse_phandle(dev->of_node,
"ae-handle",
0);
if (IS_ERR_OR_NULL(ae_node)) {
ret = PTR_ERR(ae_node);
dev_err(dev, "not find ae-handle\n");
goto out_read_prop_fail;
}
if the ae_node is NULL, PTR_ERR(ae_node) means it returns success. And the
return value should be -ENODEV.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hns V1, common_poll should check and clean fbd pkts, because it
can not pend irq to clean them if there is no new pkt comes in.
But hns V2 hw fixes this bug, and will pend irq itself to do this.
So, for hns V2, we set ring_data->fini_process to NULL.
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable head in hns_nic_tx_fini_pro has read a value, but it is
obviously no use. The patch will fix it.
And the comment is nothing to do with the routine, so it has to be removed
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return values in the first two functions mdiobus_write()
are ignored. The patch will fix it.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It misses string format in function snprintf(), as below:
snprintf(buff, ETH_GSTRING_LEN, g_gmac_stats_string[i].desc);
It needs to add "%s" to fix it as below:
snprintf(buff, ETH_GSTRING_LEN, "%s", g_gmac_stats_string[i].desc);
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cycle index should be varied while the variable j is a fixed value.
The patch will fix this bug.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When set MTU to the minimum value 68, there are increasing number
of error packets occur, which is caused by the overflowed value of
mss. This patch fix the bug.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mtu for debug port is set more than 1500, it may cause that packets
are dropped by ppe. So maximum value for debug port should be 1500.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In chip V1, the maximum mtu value is 9600. But in chip V2, it is 9728.
And it is always configurates as 9600 before this patch.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If trying to get receive flow hash indirection table by ethtool, it needs
to call .get_rxnfc to get ring number first. So this patch implements the
.get_rxnfc of ethtool. And the data type of rss_indir_table is u32, it has
to be multiply by the width of data type when using memcpy.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both .get_rxfh and .set_rxfh are always return 0, it should return result
from hardware when getting or setting rss. And the rss function should
return the correct data type.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the user manual of HNS V2 describs, XGE_DFX_CTRL_CFG.xge_dfx_ctrl_cfg
should be configed as zero if we want xge statistic reg to be read only.
But HNS V1 gets the other meanings. It needs to be identified the process
and then config it rightly.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a pause frame out from GMACs, the packets' source MAC address
does not match the GMACs' MAC address. It causes by the condition before
the mac address setting routine for GMACs, the mac address cannot be set
into loacal mac table for service ports. It obviously the condition needs
to be deleted.
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Debug ports receives lots of packets with dest mac addr does not match
local mac addr, because the filter is close, and it does not drop the
useless packets. This patch adds ON/OFF switch of filtering the packets
whose dest mac addr do not match the local addr in mac table. And the
switch is ON in initialization.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In chip V2, the default value of port id in tx BD is Zero. If it is not
configurated to the other value, all management packets will be sent out
from port0. So port_id in the tx BD needs to be updated when sending a
management packet.
In V2 chip, when sending mamagement packets, the driver should
config the port id to BD descs.
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current upstreaming code fails to ping other IPv6 net device, because
the enet receives the multicast packets with the src mac addr which is the
same as its mac addr. These packets need to be dropped.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will always be passed if the soc is tested the loopback cases. This
patch will fix this bug.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MFD_SYSCON depends on HAS_IOMEM so when selecting it avoid unmet
direct dependencies.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two header files got moved to include/linux, and most
users were already converted, this changes the remaining drivers
and removes the files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Yisen Zhuang <yisen.zhuang@huawei.com>
