There are two firmware events we handle similarly in brcmfmac:
BRCMF_E_LINK and BRCMF_E_IF. The difference from firmware point of view
is that the first one means BSS remains present in the firmware. Trying
to (re)create it (e.g. when adding new virtual interface) will result in
an error.
Current code treats both events in a similar way. It removes Linux
interface for each of them. It works OK with e.g. BCM43602. Its firmware
generates both events for each interface. It means we get BRCMF_E_LINK
and remove interface. That is soon followed by BRCMF_E_IF which means
BSS was also removed in a firmware. The only downside of this is a
harmless error like:
[ 208.643180] brcmfmac: brcmf_fweh_call_event_handler: no interface object
Unfortunately BCM4366 firmware doesn't automatically remove BSS and so
it doesn't generate BRCMF_E_IF. In such case we incorrectly remove Linux
interface on BRCMF_E_LINK as BSS is still present in the firmware. It
results in an error when trying to re-create virtual interface, e.g.:
> iw phy phy1 interface add wlan1-1 type __ap
[ 3602.929199] brcmfmac: brcmf_ap_add_vif: timeout occurred
command failed: I/O error (-5)
With this patch we don't remove Linux interface while firmware keeps
BSS. Thanks to this we keep a consistent states of host driver and
device firmware.
Further improvement should be to mark BSS as disabled and remove
interface on BRCMF_E_LINK. Then we should add support for reusing
BSS-es.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware for new chipsets is based on a new major version of code
internally maintained at Broadcom. E.g. brcmfmac4366b-pcie.bin (used for
BCM4366B1) is based on 10.10.69.3309 while brcmfmac43602-pcie.ap.bin was
based on 7.35.177.56.
Currently setting AP 5 GHz channel doesn't work reliably with BCM4366B1.
When setting e.g. 36 control channel with VHT80 (center channel 42)
firmware may randomly pick one of:
1) 52 control channel with 58 as center one
2) 100 control channel with 106 as center one
3) 116 control channel with 122 as center one
4) 149 control channel with 155 as center one
It seems new firmwares require setting AP mode (BRCMF_C_SET_AP) before
specifying a channel. Changing an order of firmware calls fixes the
problem. This requirement resulted in two separated "chanspec" calls,
one in AP code path and one in P2P path.
This fix was verified with BCM4366B1 and tested for regressions on
BCM43602.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-6 on x86 started warning about wl3501_get_encode when building
with -O2:
drivers/net/wireless/wl3501_cs.c: In function ‘wl3501_get_encode’:
drivers/net/wireless/wl3501_cs.c:1769:5: warning: ‘implemented’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1686:19: warning: ‘threshold’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1702:20: warning: ‘threshold’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1719:23: warning: ‘txpow’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1752:20: warning: ‘retry’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1806:25: warning: ‘pwr_state’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1383:24: warning: ‘value’ may be used uninitialized in this function
I could not figure out what exactly confuses gcc here, but splitting the
wl3501_get_mib_value function into two helps the compiler to figure out
that the variables are not actually used uninitialized, and makes it
slightly clearer to a human reader what the function actually does and
which parts of it are under the spinlock.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt DT
binding document lists the possible compatible strings that a SDIO child
node can have, so the driver checks if the defined in the node matches.
But the error message when that's not the case is misleading, so change
for one that makes clear what the error really is. Also, returning a -1
as errno code is not correct since that's -EPERM. A -EINVAL seems to be
a more appropriate one.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt DT
binding document say that the "interrupts" property in the child node is
optional. So the property being missed shouldn't be treated as an error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function can fail so the returned value should be checked
and the error propagated to the caller in case of a failure.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's better to have the device name prefixed in the error message.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of duplicating part of the cleanups needed in case of an error
in .probe callback, have a single error path and use goto labels as is
common practice in the kernel.
This also has the nice side effect that the cleanup operations are made
in the inverse order of their counterparts, which was not the case for
the mwifiex_add_card() error path.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There's only a check if mwifiex_add_card() returned a nonzero value, but
the actual error code is neither stored nor propagated to the caller. So
instead of always returning -1 (which is -EPERM and not a suitable errno
code in this case), propagate the value returned by mwifiex_add_card().
Patch also removes the assignment of sdio_disable_func() returned value
since it was overwritten anyways and what matters is to know the error
value returned by the first function that failed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the sdio_enable_func() function fails on .probe, the -EIO errno code
is always returned but that could make more difficult to debug and find
the cause of why the function actually failed.
Since the driver/device core prints the value returned by .probe in its
error message propagate what was returned by sdio_enable_func() at fail.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO is an auto enumerable bus so the SDIO devices are matched using the
sdio_device_id table and not using compatible strings from a OF id table.
However, commit ce4f6f0c35 ("mwifiex: add platform specific wakeup
interrupt support") allowed to match nodes defined as child of the SDIO
host controller in the probe function using a compatible string to setup
platform specific parameters in the DT.
The problem is that the OF parse function is always called regardless if
the SDIO dev has an OF node associated or not, and prints an error if it
is not found. So, on a platform that doesn't have a node for a SDIO dev,
the following misleading error message will be printed:
[ 12.480042] mwifiex_sdio mmc2:0001:1: sdio platform data not available
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is helpful for debugging. Without this all I was getting from "iw"
command on failed creating of P2P interface was:
> command failed: Too many open files in system (-23)
Signed-off-by: Rafal Milecki <zajec5@gmail.com>
[arend@broadcom.com: reduce error prints upon iface creation]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Daniel Borkmann says:
====================
bpf: improve fd array release
This set improves BPF perf fd array map release wrt to purging
entries, first two extend the API as needed. Please see individual
patches for more details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The behavior of perf event arrays are quite different from all
others as they are tightly coupled to perf event fds, f.e. shown
recently by commit e03e7ee34f ("perf/bpf: Convert perf_event_array
to use struct file") to make refcounting on perf event more robust.
A remaining issue that the current code still has is that since
additions to the perf event array take a reference on the struct
file via perf_event_get() and are only released via fput() (that
cleans up the perf event eventually via perf_event_release_kernel())
when the element is either manually removed from the map from user
space or automatically when the last reference on the perf event
map is dropped. However, this leads us to dangling struct file's
when the map gets pinned after the application owning the perf
event descriptor exits, and since the struct file reference will
in such case only be manually dropped or via pinned file removal,
it leads to the perf event living longer than necessary, consuming
needlessly resources for that time.
Relations between perf event fds and bpf perf event map fds can be
rather complex. F.e. maps can act as demuxers among different perf
event fds that can possibly be owned by different threads and based
on the index selection from the program, events get dispatched to
one of the per-cpu fd endpoints. One perf event fd (or, rather a
per-cpu set of them) can also live in multiple perf event maps at
the same time, listening for events. Also, another requirement is
that perf event fds can get closed from application side after they
have been attached to the perf event map, so that on exit perf event
map will take care of dropping their references eventually. Likewise,
when such maps are pinned, the intended behavior is that a user
application does bpf_obj_get(), puts its fds in there and on exit
when fd is released, they are dropped from the map again, so the map
acts rather as connector endpoint. This also makes perf event maps
inherently different from program arrays as described in more detail
in commit c9da161c65 ("bpf: fix clearing on persistent program
array maps").
To tackle this, map entries are marked by the map struct file that
added the element to the map. And when the last reference to that map
struct file is released from user space, then the tracked entries
are purged from the map. This is okay, because new map struct files
instances resp. frontends to the anon inode are provided via
bpf_map_new_fd() that is called when we invoke bpf_obj_get_user()
for retrieving a pinned map, but also when an initial instance is
created via map_create(). The rest is resolved by the vfs layer
automatically for us by keeping reference count on the map's struct
file. Any concurrent updates on the map slot are fine as well, it
just means that perf_event_fd_array_release() needs to delete less
of its own entires.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends map_fd_get_ptr() callback that is used by fd array
maps, so that struct file pointer from the related map can be passed
in. It's safe to remove map_update_elem() callback for the two maps since
this is only allowed from syscall side, but not from eBPF programs for these
two map types. Like in per-cpu map case, bpf_fd_array_map_update_elem()
needs to be called directly here due to the extra argument.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a release callback for maps that is invoked when the last
reference to its struct file is gone and the struct file about
to be released by vfs. The handler will be used by fd array maps.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree says:
====================
sfc: RX VLAN filtering
Adds support for VLAN-qualified receive filters on EF10 hardware.
This is needed when running as a guest if the hypervisor has enabled
vfs-vlan-restrict, in which case the firmware rejects filters not qualified
with VLAN 0.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If vPort has VLAN_RESTRICT flag, VLAN tagged traffic will not be
delivered without corresponding Rx filters which may be proxied to and
moderated by hypervisor.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If should be done after net_dev->hw_features initialization, to keep the
feature there to be able to enable it later using ethtool.
VLAN filtering is enforced and fixed if vPort requires usage of VLAN
filters to receive tagged traffic.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If it is not supported we simply disable the feature.
For the feature to work we need firmware filter support for
OUTER_VID + LOC_MAC and for OUTER_VID + LOC_MAC_IG.
The low-latency firmware can match on OUTER_VID + LOC_MAC but not on
OUTER_VID + LOC_MAC_IG.
For the capture packet firmware it is the other way around.
Only the full-feature variant can match on both combinations.
Incorporates a fix by Andrew Rybchenko <Andrew.Rybchenko@oktetlabs.ru>
in the net_dev->[hw_]features handling.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filter match flags are not unique criteria to be mapped to priority
because of both unknown unicast and unknown multicast are mapped to
LOC_MAC_IG. So, local MAC is required to map filter to priority.
MCDI filter flags is unique criteria to find filter priority.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nearly every time we call efx_ef10_filter_remove_unsafe, we first check
for EFX_EF10_FILTER_ID_INVALID, in which case we do nothing. So move
that check into the function, simplifying all the call sites.
Also, change the return type to void, since none of the callers check it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to enslave an SFC interface to a bond the following BUG_ON was
hit:
kernel BUG [in ef10.c]!
CPU: 0 PID: 4383 Comm: ifenslave Tainted: G
...
Call Trace:
efx_ef10_filter_add_vlan+0x121/0x180 [sfc]
efx_ef10_filter_table_probe+0x2a2/0x4f0 [sfc]
efx_ef10_set_mac_address+0x370/0x6d0 [sfc]
efx_set_mac_address+0x7d/0x120 [sfc]
dev_set_mac_address+0x43/0xa0
bond_enslave+0x337/0xea0 [bonding]
This comes from function efx_ef10_filter_vlan_sync_rx_mode.
To solve the bug we ensure the mac_lock is taken before calling
efx_ef10_filter_add_vlan. But to avoid a priority inversion mac_lock must
be taken before filter_sem.
To satisfy these requirements we end up taking mac_lock in
efx_ef10_vport_set_mac_address, efx_ef10_set_mac_address,
efx_ef10_sriov_set_vf_vlan and efx_probe_filters.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supports HW VLAN filtering, en/disabled using ethtool.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now it contains dummy VLAN entry with unspecified VID only.
The entry is used for the case when HW VLAN filtering is not used.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These flags are built when address cache is updated.
The information will be required when VLAN filtering is added and address
cache is used without re-sync.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a step to support VLAN filtering in HW.
Until then, there is only one struct efx_ef10_filter_vlan per struct
efx_ef10_filter_table, with no VLAN information yet.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is required to remove setting of filter IDs to invalid from multicast
and unicast addresses caching functions.
Add initialization to invalid when filter table is created.
Add paranoid checks to track consistency.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on a patch by Andrew Rybchenko <Andrew.Rybchenko@oktetlabs.ru>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It allows to change set of fixed features on datapath reset.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is used for EF10 only and logically belongs to EF10 filter table state.
It is OK that it is reset to false on filter table recreation since all
filters are removed on destruction.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HOTh
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20160615' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Rework endpoint record handling
Here's the next part of the AF_RXRPC rewrite. In this set I rework
endpoint record handling. There are two types of endpoint record, local
and peer. The local endpoint record is used as an anchor for the transport
socket that AF_RXRPC uses (at the moment a UDP socket). Local endpoints
can be shared between AF_RXRPC sockets under certain restricted
circumstances.
The peer endpoint is a record of the remote end. It is (or will be) used
to keep track MTU and RTT values and, with these changes, is used to find
the call(s) to abort when a network error occurs.
The following significant changes are made:
(1) The local endpoint event handling code is split out into its own file.
(2) The local endpoint list bottom half-excluding spinlock is removed as
things are arranged such that sk_user_data will not change whilst the
transport socket callbacks are in progress.
(3) Local endpoints can now only be shared if they have the same transport
address (as before) and have a local service ID of 0 (ie. they're not
listening for incoming calls). This prevents callbacks from a server
to one process being picked up by another process.
(4) Local endpoint destruction is now accomplished by the same work item
as processes events, meaning that the destructor doesn't need to wait
for the event processor.
(5) Peer endpoints are now held in a hash table rather than a flat list.
(6) Peer endpoints are now destroyed by RCU rather than by work item.
(7) Peer endpoints are now differentiated by local endpoint and remote
transport port in addition to remote transport address and transport
type and family.
This means that a firewall that excludes access between a particular
local port and remote port won't cause calls to be aborted that use a
different port pair.
(8) Error report handling now no longer assumes that the source is always
an IPv4 ICMP message from a UDP port and has assumptions that an ICMP
message comes from an IPv4 socket removed. At some point IPv6 support
will be added.
(9) Peer endpoints rather than local endpoints are now the anchor point
for distributing network error reports.
(10) Both types of endpoint records are now disposed of as soon as all
references to them are gone. There is less hanging around and once
their usage counts hit zero, records can no longer be resurrected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi says:
====================
liquidio: Updates and Bug fixes
Following are updates for liquidio bug fixes and driver
support for new firmware interface. These updates are divided
into smaller logical patches as mentioned by you. These set of
nine patches should be applied in the following order as some of
them depend on earlier patches in the list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for new instruction header for octeon2/octeon3(ih) and
corresponding changes.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch decoupled the firmware side ifidx and host side interface
number. It also has some minor name change for linkinfo sturct field.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is for new driver/firmware control command structure
(octnic_packet_params and octnic_cmd_setup ) and resultant code changes.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to refactor packet size calculations to support PTP enabled
for 66xx and 68xx cards and also other cards that do not support PTP.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add page based buffers for receive side descriptors of
the driver and separate free routines for rx and tx buffers.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to allocate rx queue's memory based on numa node and also use
page based buffers for rx traffic improvements.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to allocate and manage scatter gather lists per
input queue(iq's) and remove queue's interdependence.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to allocate the input queues based on Numa node in tx path
and queue mapping changes based on the mapping info provided by firmware.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to resolve the double free issue by checking proper return
values from soft command.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The algorithm for checksum neutral mapping is incorrect. This problem
was being hidden since we were previously always performing checksum
offload on the translated addresses and only with IPv6 HW csum.
Enabling an ILA router shows the issue.
Corrected algorithm:
old_loc is the original locator in the packet, new_loc is the value
to overwrite with and is found in the lookup table. old_flag is
the old flag value (zero of CSUM_NEUTRAL_FLAG) and new_flag is
then (old_flag ^ CSUM_NEUTRAL_FLAG) & CSUM_NEUTRAL_FLAG.
Need SUM(new_id + new_flag + diff) == SUM(old_id + old_flag) for
checksum neutral translation.
Solving for diff gives:
diff = (old_id - new_id) + (old_flag - new_flag)
compute_csum_diff8(new_id, old_id) gives old_id - new_id
If old_flag is set
old_flag - new_flag = old_flag = CSUM_NEUTRAL_FLAG
Else
old_flag - new_flag = -new_flag = ~CSUM_NEUTRAL_FLAG
Tested:
- Implemented a user space program that creates random addresses
and random locators to overwrite. Compares the checksum over
the address before and after translation (must always be equal)
- Enabled ILA router and showed proper operation.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the presence of firewalls which improperly block ICMP Unreachable
(including Fragmentation Required) messages, Path MTU Discovery is
prevented from working.
A workaround is to handle IPv4 payloads opaquely, ignoring the DF bit--as
is done for other payloads like AppleTalk--and doing transparent
fragmentation and reassembly.
Redux includes the enforcement of mutual exclusion between this feature
and Path MTU Discovery as suggested by Alexander Duyck.
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempting to delete a VRF device with a socket bound to it can stall:
unregister_netdevice: waiting for red to become free. Usage count = 1
The unregister is waiting for the dst to be released and with it
references to the vrf device. Similar to dst_ifdown switch the dst
dev to loopback on delete for all of the dst's for the vrf device
and release the references to the vrf device.
Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is Mellanox mlx5_core shared code for both net-next and RDMA
trees for 4.8 kernel cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=93xr
-----END PGP SIGNATURE-----
Merge tag 'shared' of git://git.kernel.org/pub/scm/linux/kernel/git/leon/linux-rdma
Mellanox shared code between RDMA and net-next trees
This is Mellanox mlx5_core shared code for both net-next and RDMA
trees for 4.8 kernel cycle.
The latest changes to the MDIO code introduced a false-positive
warning with gcc-6 (possibly others):
drivers/net/phy/mdio-mux.c: In function 'mdio_mux_init':
drivers/net/phy/mdio-mux.c:188:3: error: 'parent_bus_node' may be used uninitialized in this function [-Werror=maybe-uninitialized]
It's easy to avoid the warning by making sure the parent_bus_node
is initialized in both cases at the start of the function, since
the later 'of_node_put()' call is also valid for a NULL pointer
argument.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f20e6657a8 ("mdio: mux: Enhanced MDIO mux framework for integrated multiplexers")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
