1. receive status
sender receiver receiver
ACK:CR ACK:CR ACK:CR
2. sender get EX of TOKEN
sender get EX of MESSAGE
sender receiver receiver
TOKEN:EX ACK:CR ACK:CR
MESSAGE:EX
ACK:CR
3. sender write LVB.
sender down-convert MESSAGE from EX to CR
sender try to get EX of ACK
[ wait until all receiver has *processed* the MESSAGE ]
[ triggered by bast of ACK ]
receiver get CR of MESSAGE
receiver read LVB
receiver processes the message
[ wait finish ]
receiver release ACK
sender receiver receiver
TOKEN:EX MESSAGE:CR MESSAGE:CR
MESSAGE:CR
ACK:EX
4. sender down-convert ACK from EX to CR
sender release MESSAGE
sender release TOKEN
receiver upconvert to EX of MESSAGE
receiver get CR of ACK
receiver release MESSAGE
sender receiver receiver
ACK:CR ACK:CR ACK:CR
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
The DLM informs us in case of node failure with the DLM slot number.
cluster_info->recovery_map sets the bit corresponding to the slot number
and wakes up the recovery thread.
The recovery thread:
1. Derives the slot number from the recovery_map
2. Locks the bitmap corresponding to the slot
3. Copies the set bits to the node-local bitmap
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
bitmap_copy_from_slot reads the bitmap from the slot mentioned.
It then copies the set bits to the node local bitmap.
This is helper function for the resync operation on node failure.
bitmap_set_memory_bits() currently assumes it is only run at startup and that
they bitmap is currently empty. So if it finds that a region is already
marked as dirty, it won't mark it dirty again. Change bitmap_set_memory_bits()
to always set the NEEDED_MASK bit if 'needed' is set.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
When a node joins, it does not know of other nodes performing resync.
So, each node keeps the resync information in it's LVB. When a new
node joins, it reads the LVB of each "online" bitmap.
[TODO] The new node attempts to get the PW lock on other bitmap, if
it is successful, it reads the bitmap and performs the resync (if
required) on it's behalf.
If the node does not get the PW, it requests CR and reads the LVB
for the resync information.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
On-disk format:
0 4k 8k 12k
-------------------------------------------------------------------
| idle | md super | bm super [0] + bits |
| bm bits[0, contd] | bm super[1] + bits | bm bits[1, contd] |
| bm super[2] + bits | bm bits [2, contd] | bm super[3] + bits |
| bm bits [3, contd] | | |
Bitmap super has a field nodes, which defines the maximum number
of nodes the device can use. While reading the bitmap super, if
the cluster finds out that the number of nodes is > 0:
1. Requests the md-cluster module.
2. Calls md_cluster_ops->join(), which sets up clustering such as
joining DLM lockspace.
Since the first time, the first bitmap is read. After the call
to the cluster_setup, the bitmap offset is adjusted and the
superblock is re-read. This also ensures the bitmap is read
the bitmap lock (when bitmap lock is introduced in later patches)
Questions:
1. cluster name is repeated in all bitmap supers. Is that okay?
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
DLM offers callbacks when a node fails and the lock remastery
is performed:
1. recover_prep: called when DLM discovers a node is down
2. recover_slot: called when DLM identifies the node and recovery
can start
3. recover_done: called when all nodes have completed recover_slot
recover_slot() and recover_done() are also called when the node joins
initially in order to inform the node with its slot number. These slot
numbers start from one, so we deduct one to make it start with zero
which the cluster-md code uses.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
md_cluster_info stores the cluster information in the MD device.
The join() is called when mddev detects it is a clustered device.
The main responsibilities are:
1. Setup a DLM lockspace
2. Setup all initial locks such as super block locks and bitmap lock (will come later)
The leave() clears up the lockspace and all the locks held.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
A dlm_lock_resource is a structure which contains all information
required for locking using DLM. The init function allocates the
lock and acquires the lock in NL mode. The unlock function
converts the lock resource to NL mode. This is done to preserve
LVB and for faster processing of locks. The lock resource is
DLM unlocked only in the lockres_free function, which is the end
of life of the lock resource.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
to changes that enable effective use of an unbound workqueue across
all available CPUs. A large battery of tests were performed to
validate these changes, summary of results is available here:
https://www.redhat.com/archives/dm-devel/2015-February/msg00106.html
- A few additional stable fixes (to DM core, dm-snapshot and dm-mirror)
and a small fix to the dm-space-map-disk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU51MsAAoJEMUj8QotnQNan8wH/3Oa2/ofbX8zNYtdDxFBK7W0
pHwVA2CH9yzDDi90X9GsQODmXerMrYf+SHo/RsQTpSnt5WI/4ZVP/1EoNGu6T2Yr
XiaKc/Jwo+ScxdhoHSNtyGL5vKeipX6clgz1wcd/4/UBcBAr0Vxj25s8Ta7naK2V
hZyWnt3MCGEDQ45NVBmLOU78Cl68LGf8JOUY0l3cd8ehQjGyR9a12GXwRktepslp
hw9xu8uYmE93fD+MIe/fUs7W/WvIVgFSskhswlvD3kAFpEAsMczjLGVSRQlBE90L
OK7v1HKxiIUJa17g3LmiCFa59ZjrnSHGpOOv9IPAFU/LzFIU47lcFwRFjgfB8po=
=8vFi
-----END PGP SIGNATURE-----
Merge tag 'dm-3.20-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull more device mapper changes from Mike Snitzer:
- Significant dm-crypt CPU scalability performance improvements thanks
to changes that enable effective use of an unbound workqueue across
all available CPUs. A large battery of tests were performed to
validate these changes, summary of results is available here:
https://www.redhat.com/archives/dm-devel/2015-February/msg00106.html
- A few additional stable fixes (to DM core, dm-snapshot and dm-mirror)
and a small fix to the dm-space-map-disk.
* tag 'dm-3.20-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm snapshot: fix a possible invalid memory access on unload
dm: fix a race condition in dm_get_md
dm crypt: sort writes
dm crypt: add 'submit_from_crypt_cpus' option
dm crypt: offload writes to thread
dm crypt: remove unused io_pool and _crypt_io_pool
dm crypt: avoid deadlock in mempools
dm crypt: don't allocate pages for a partial request
dm crypt: use unbound workqueue for request processing
dm io: reject unsupported DISCARD requests with EOPNOTSUPP
dm mirror: do not degrade the mirror on discard error
dm space map disk: fix sm_disk_count_is_more_than_one()
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
When the snapshot target is unloaded, snapshot_dtr() waits until
pending_exceptions_count drops to zero. Then, it destroys the snapshot.
Therefore, the function that decrements pending_exceptions_count
should not touch the snapshot structure after the decrement.
pending_complete() calls free_pending_exception(), which decrements
pending_exceptions_count, and then it performs up_write(&s->lock) and it
calls retry_origin_bios() which dereferences s->origin. These two
memory accesses to the fields of the snapshot may touch the dm_snapshot
struture after it is freed.
This patch moves the call to free_pending_exception() to the end of
pending_complete(), so that the snapshot will not be destroyed while
pending_complete() is in progress.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
The function dm_get_md finds a device mapper device with a given dev_t,
increases the reference count and returns the pointer.
dm_get_md calls dm_find_md, dm_find_md takes _minor_lock, finds the
device, tests that the device doesn't have DMF_DELETING or DMF_FREEING
flag, drops _minor_lock and returns pointer to the device. dm_get_md then
calls dm_get. dm_get calls BUG if the device has the DMF_FREEING flag,
otherwise it increments the reference count.
There is a possible race condition - after dm_find_md exits and before
dm_get is called, there are no locks held, so the device may disappear or
DMF_FREEING flag may be set, which results in BUG.
To fix this bug, we need to call dm_get while we hold _minor_lock. This
patch renames dm_find_md to dm_get_md and changes it so that it calls
dm_get while holding the lock.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
yet-another-livelock in raid5, and a problem with write errors
to 4K-block devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIVAwUAVOPorznsnt1WYoG5AQKa5A//RmLurotaJvHt8YA8jzlzo2KY/9jxIv8x
jF0CQ0Kva056GG27dlkMPBoddrVk7/WaCoz/ICBKgfSTCpiEFekNlExLkeLXrgUb
mKljS/HKhP4KQjiy519HiT2v9BRTqZD3l6P2405qVAZGTymwhelAp3y1I5ZIRFOr
k2Uo6PNT/XYvzwWAy5iEBrE7zZl3MZJG5RjW2Wq6JKaWMUQaQERu5OhugWEfCI3U
yVomILlwiYqC85WLgrVob/OqCSoA3UsIZkZKvKJCP8Y4C9QJzquEeZy4z0swgJq0
FMsu2WqmI3/ZNFvmlSozN05CEUMkZF6E8hGJcT+f1Wa1NE40zrzDkVsVvsGMD8v0
Ek7PTiA3X7AhqRl4Lt2Gs8kfDJ9MIRXzvXJv9UUO7PtVQGUhVdqmcqsodyqA7+lw
63hgSpEUtQTkpeWwcYQY6Impr/6jGxHwQKzFlLltaDvmAeOBd6gjAq2bdfPO5tox
FiSoClhor4yTc274+s5ORk9xDh61d7ZbnFJ+QN7YioyaSD2LHYIl9EkVFDe4OMXV
q39VzXt+uEYx6hxfmnpjPyPvPiyuDsnXzoTMcaaGsJL4TOazoIEj5AFGmg5i3/yw
6UVjKxJ43SMM7qg3VbgZpenGJwvRkP5mqQwMNDZICXdWulQTMwM5w3AidNqwYAaU
oEPAMfZNGvE=
=1BWV
-----END PGP SIGNATURE-----
Merge tag 'md/3.20-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"Three bug md fixes for 3.20
yet-another-livelock in raid5, and a problem with write errors to
4K-block devices"
* tag 'md/3.20-fixes' of git://neil.brown.name/md:
md/raid5: Fix livelock when array is both resyncing and degraded.
md/raid10: round up to bdev_logical_block_size in narrow_write_error.
md/raid1: round up to bdev_logical_block_size in narrow_write_error
Commit a7854487cd:
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
Causes an RCW cycle to be forced even when the array is degraded.
A degraded array cannot support RCW as that requires reading all data
blocks, and one may be missing.
Forcing an RCW when it is not possible causes a live-lock and the code
spins, repeatedly deciding to do something that cannot succeed.
So change the condition to only force RCW on non-degraded arrays.
Reported-by: Manibalan P <pmanibalan@amiindia.co.in>
Bisected-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: a7854487cd
Cc: stable@vger.kernel.org (v3.7+)
Write requests are sorted in a red-black tree structure and are
submitted in the sorted order.
In theory the sorting should be performed by the underlying disk
scheduler, however, in practice the disk scheduler only accepts and
sorts a finite number of requests. To allow the sorting of all
requests, dm-crypt needs to implement its own sorting.
The overhead associated with rbtree-based sorting is considered
negligible so it is not used conditionally. Even on SSD sorting can be
beneficial since in-order request dispatch promotes lower latency IO
completion to the upper layers.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Make it possible to disable offloading writes by setting the optional
'submit_from_crypt_cpus' table argument.
There are some situations where offloading write bios from the
encryption threads to a single thread degrades performance
significantly.
The default is to offload write bios to the same thread because it
benefits CFQ to have writes submitted using the same IO context.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Submitting write bios directly in the encryption thread caused serious
performance degradation. On a multiprocessor machine, encryption requests
finish in a different order than they were submitted. Consequently, write
requests would be submitted in a different order and it could cause severe
performance degradation.
Move the submission of write requests to a separate thread so that the
requests can be sorted before submitting. But this commit improves
dm-crypt performance even without having dm-crypt perform request
sorting (in particular it enables IO schedulers like CFQ to sort more
effectively).
Note: it is required that a previous commit ("dm crypt: don't allocate
pages for a partial request") be applied before applying this patch.
Otherwise, this commit could introduce a crash.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The previous commit ("dm crypt: don't allocate pages for a partial
request") stopped using the io_pool slab mempool and backing
_crypt_io_pool kmem cache.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fix a theoretical deadlock introduced in the previous commit ("dm crypt:
don't allocate pages for a partial request").
The function crypt_alloc_buffer may be called concurrently. If we allocate
from the mempool concurrently, there is a possibility of deadlock. For
example, if we have mempool of 256 pages, two processes, each wanting
256, pages allocate from the mempool concurrently, it may deadlock in a
situation where both processes have allocated 128 pages and the mempool
is exhausted.
To avoid such a scenario we allocate the pages under a mutex. In order
to not degrade performance with excessive locking, we try non-blocking
allocations without a mutex first and if that fails, we fallback to a
blocking allocations with a mutex.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Change crypt_alloc_buffer so that it only ever allocates pages for a
full request. This is a prerequisite for the commit "dm crypt: offload
writes to thread".
This change simplifies the dm-crypt code at the expense of reduced
throughput in low memory conditions (where allocation for a partial
request is most useful).
Note: the next commit ("dm crypt: avoid deadlock in mempools") is needed
to fix a theoretical deadlock.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use unbound workqueue by default so that work is automatically balanced
between available CPUs. The original behavior of encrypting using the
same cpu that IO was submitted on can still be enabled by setting the
optional 'same_cpu_crypt' table argument.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This modifies raid1's narrow_write_error to round up block_sectors to the
device's logical block size.
This prevents sd complaining about "Bad block number requested" for non-512-byte
sector disks.
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
I created a dm-raid1 device backed by a device that supports DISCARD
and another device that does NOT support DISCARD with the following
dm configuration:
# echo '0 2048 mirror core 1 512 2 /dev/sda 0 /dev/sdb 0' | dmsetup create moo
# lsblk -D
NAME DISC-ALN DISC-GRAN DISC-MAX DISC-ZERO
sda 0 4K 1G 0
`-moo (dm-0) 0 4K 1G 0
sdb 0 0B 0B 0
`-moo (dm-0) 0 4K 1G 0
Notice that the mirror device /dev/mapper/moo advertises DISCARD
support even though one of the mirror halves doesn't.
If I issue a DISCARD request (via fstrim, mount -o discard, or ioctl
BLKDISCARD) through the mirror, kmirrord gets stuck in an infinite
loop in do_region() when it tries to issue a DISCARD request to sdb.
The problem is that when we call do_region() against sdb, num_sectors
is set to zero because q->limits.max_discard_sectors is zero.
Therefore, "remaining" never decreases and the loop never terminates.
To fix this: before entering the loop, check for the combination of
REQ_DISCARD and no discard and return -EOPNOTSUPP to avoid hanging up
the mirror device.
This bug was found by the unfortunate coincidence of pvmove and a
discard operation in the RHEL 6.5 kernel; upstream is also affected.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
It may be possible that a device claims discard support but it rejects
discards with -EOPNOTSUPP. It happens when using loopback on ext2/ext3
filesystem driven by the ext4 driver. It may also happen if the
underlying devices are moved from one disk on another.
If discard error happens, we reject the bio with -EOPNOTSUPP, but we do
not degrade the array.
This patch fixes failed test shell/lvconvert-repair-transient.sh in the
lvm2 testsuite if the testsuite is extracted on an ext2 or ext3
filesystem and it is being driven by the ext4 driver.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
dm_tm_shadow_block() is the only caller of
dm_sm_count_is_more_than_one() which only ever operates on a metadata
space-map. So in practice, sm_disk_count_is_more_than_one() isn't
actually used (which explains why this bug never amounted to anything).
But fix sm_disk_count_is_more_than_one() to properly set *result and
return 0.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
stacking ontop of blk-mq devices. This blk-mq support changes the
model request-based DM uses for cloning a request to relying on
calling blk_get_request() directly from the underlying blk-mq device.
Early consumer of this code is Intel's emerging NVMe hardware; thanks
to Keith Busch for working on, and pushing for, these changes.
- A few other small fixes and cleanups across other DM targets.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU3NRnAAoJEMUj8QotnQNavG0H/3yogMcHvKg9H+w0WmUQdwhN
w99Wj3nkquAw2sm9yahKlAMBNY53iu/LHmC6/PaTpJetgdH7y1foTrRa0qjyeB2D
DgNr8mOzxSxzX6CX9V8JMwqzky9XoG2IOt/7FeQQOpMqp4T1M2zgvbZtpl0lK/f3
lNaNBFpl+47NbGssD/WbtfI4Yy3hX0u406yGmQN5DxRyGTWD2AFqpA76g2mp8vrp
wmw259gPr4oLhj3pDc0GkuiVn59ZR2Zp+2gs0jD5uKlDL84VP/nE+WNB+ny1Mnmt
cOg8Q+W6/OosL66MKBHNsF0QS6DXNo5UvsN9fHGa5IUJw7Tsa11ZEPKHZGEbQw4=
=RiN2
-----END PGP SIGNATURE-----
Merge tag 'dm-3.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper changes from Mike Snitzer:
- The most significant change this cycle is request-based DM now
supports stacking ontop of blk-mq devices. This blk-mq support
changes the model request-based DM uses for cloning a request to
relying on calling blk_get_request() directly from the underlying
blk-mq device.
An early consumer of this code is Intel's emerging NVMe hardware;
thanks to Keith Busch for working on, and pushing for, these changes.
- A few other small fixes and cleanups across other DM targets.
* tag 'dm-3.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: inherit QUEUE_FLAG_SG_GAPS flags from underlying queues
dm snapshot: remove unnecessary NULL checks before vfree() calls
dm mpath: simplify failure path of dm_multipath_init()
dm thin metadata: remove unused dm_pool_get_data_block_size()
dm ioctl: fix stale comment above dm_get_inactive_table()
dm crypt: update url in CONFIG_DM_CRYPT help text
dm bufio: fix time comparison to use time_after_eq()
dm: use time_in_range() and time_after()
dm raid: fix a couple integer overflows
dm table: train hybrid target type detection to select blk-mq if appropriate
dm: allocate requests in target when stacking on blk-mq devices
dm: prepare for allocating blk-mq clone requests in target
dm: submit stacked requests in irq enabled context
dm: split request structure out from dm_rq_target_io structure
dm: remove exports for request-based interfaces without external callers
Pull core block IO changes from Jens Axboe:
"This contains:
- A series from Christoph that cleans up and refactors various parts
of the REQ_BLOCK_PC handling. Contributions in that series from
Dongsu Park and Kent Overstreet as well.
- CFQ:
- A bug fix for cfq for realtime IO scheduling from Jeff Moyer.
- A stable patch fixing a potential crash in CFQ in OOM
situations. From Konstantin Khlebnikov.
- blk-mq:
- Add support for tag allocation policies, from Shaohua. This is
a prep patch enabling libata (and other SCSI parts) to use the
blk-mq tagging, instead of rolling their own.
- Various little tweaks from Keith and Mike, in preparation for
DM blk-mq support.
- Minor little fixes or tweaks from me.
- A double free error fix from Tony Battersby.
- The partition 4k issue fixes from Matthew and Boaz.
- Add support for zero+unprovision for blkdev_issue_zeroout() from
Martin"
* 'for-3.20/core' of git://git.kernel.dk/linux-block: (27 commits)
block: remove unused function blk_bio_map_sg
block: handle the null_mapped flag correctly in blk_rq_map_user_iov
blk-mq: fix double-free in error path
block: prevent request-to-request merging with gaps if not allowed
blk-mq: make blk_mq_run_queues() static
dm: fix multipath regression due to initializing wrong request
cfq-iosched: handle failure of cfq group allocation
block: Quiesce zeroout wrapper
block: rewrite and split __bio_copy_iov()
block: merge __bio_map_user_iov into bio_map_user_iov
block: merge __bio_map_kern into bio_map_kern
block: pass iov_iter to the BLOCK_PC mapping functions
block: add a helper to free bio bounce buffer pages
block: use blk_rq_map_user_iov to implement blk_rq_map_user
block: simplify bio_map_kern
block: mark blk-mq devices as stackable
block: keep established cmd_flags when cloning into a blk-mq request
block: add blk-mq support to blk_insert_cloned_request()
block: require blk_rq_prep_clone() be given an initialized clone request
blk-mq: add tag allocation policy
...
- assorted locking changes so that access to /proc/mdstat
and much of /sys/block/mdXX/md/* is protected by a spinlock
rather than a mutex and will never block indefinitely.
- Make an 'if' condition in RAID5 - which has been implicated
in recent bugs - more readable.
- misc minor fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/FmP
-----END PGP SIGNATURE-----
Merge tag 'md/3.20' of git://neil.brown.name/md
Pull md updates from Neil Brown:
- assorted locking changes so that access to /proc/mdstat
and much of /sys/block/mdXX/md/* is protected by a spinlock
rather than a mutex and will never block indefinitely.
- Make an 'if' condition in RAID5 - which has been implicated
in recent bugs - more readable.
- misc minor fixes
* tag 'md/3.20' of git://neil.brown.name/md: (28 commits)
md/raid10: fix conversion from RAID0 to RAID10
md: wakeup thread upon rdev_dec_pending()
md: make reconfig_mutex optional for writes to md sysfs files.
md: move mddev_lock and related to md.h
md: use mddev->lock to protect updates to resync_{min,max}.
md: minor cleanup in safe_delay_store.
md: move GET_BITMAP_FILE ioctl out from mddev_lock.
md: tidy up set_bitmap_file
md: remove unnecessary 'buf' from get_bitmap_file.
md: remove mddev_lock from rdev_attr_show()
md: remove mddev_lock() from md_attr_show()
md/raid5: use ->lock to protect accessing raid5 sysfs attributes.
md: remove need for mddev_lock() in md_seq_show()
md/bitmap: protect clearing of ->bitmap by mddev->lock
md: protect ->pers changes with mddev->lock
md: level_store: group all important changes into one place.
md: rename ->stop to ->free
md: split detach operation out from ->stop.
md/linear: remove rcu protections in favour of suspend/resume
md: make merge_bvec_fn more robust in face of personality changes.
...
A RAID0 array (like a LINEAR array) does not have a concept
of 'size' being the amount of each device that is in use.
Rather, as much of each device as is available is used.
So the 'size' is set to 0 and ignored.
RAID10 does have this concept and needs it to be set correctly.
So when we convert RAID0 to RAID10 we must determine the
'size' (that being the size of the first 'strip_zone' in the
RAID0), and set it correctly.
Reported-and-tested-by: Xiao Ni <xni@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
A DM device must inherit the QUEUE_FLAG_SG_GAPS flags from its
underlying block devices' request queues.
This fixes problems when submitting cloned requests to multipathed
devices requiring virtually contiguous buffers.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pull RCU updates from Ingo Molnar:
"The main RCU changes in this cycle are:
- Documentation updates.
- Miscellaneous fixes.
- Preemptible-RCU fixes, including fixing an old bug in the
interaction of RCU priority boosting and CPU hotplug.
- SRCU updates.
- RCU CPU stall-warning updates.
- RCU torture-test updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
rcu: Initialize tiny RCU stall-warning timeouts at boot
rcu: Fix RCU CPU stall detection in tiny implementation
rcu: Add GP-kthread-starvation checks to CPU stall warnings
rcu: Make cond_resched_rcu_qs() apply to normal RCU flavors
rcu: Optionally run grace-period kthreads at real-time priority
ksoftirqd: Use new cond_resched_rcu_qs() function
ksoftirqd: Enable IRQs and call cond_resched() before poking RCU
rcutorture: Add more diagnostics in rcu_barrier() test failure case
torture: Flag console.log file to prevent holdovers from earlier runs
torture: Add "-enable-kvm -soundhw pcspk" to qemu command line
rcutorture: Handle different mpstat versions
rcutorture: Check from beginning to end of grace period
rcu: Remove redundant rcu_batches_completed() declaration
rcutorture: Drop rcu_torture_completed() and friends
rcu: Provide rcu_batches_completed_sched() for TINY_RCU
rcutorture: Use unsigned for Reader Batch computations
rcutorture: Make build-output parsing correctly flag RCU's warnings
rcu: Make _batches_completed() functions return unsigned long
rcutorture: Issue warnings on close calls due to Reader Batch blows
documentation: Fix smp typo in memory-barriers.txt
...
The vfree() function performs input parameter validation.
Thus the NULL pointer test around vfree() calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Currently the cleanup of all error cases are open-coded. Introduce a
common exit path and labels.
Signed-off-by: Johannes Thumshirn <morbidrsa@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The thin-pool target doesn't display the data block size as part of
its table status, unlike the dm-cache target, so there is no need for
dm_pool_get_data_block_size().
This was found using cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Update the obsolete url in the CONFIG_DM_CRYPT help text.
Signed-off-by: Loic Pefferkorn <loic@loicp.eu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
To be future-proof and for better readability the time comparison
is modified to use time_after_eq() instead of plain, error-prone math.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
To be future-proof and for better readability the time comparisons are modified
to use time_in_range() and time_after() instead of plain, error-prone math.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
My static checker complains that if "num_raid_params" is UINT_MAX then
the "if (num_raid_params + 1 > argc) {" check doesn't work as intended.
The other change is that I moved the "if (argc != (num_raid_devs * 2))"
condition forward a few lines so it was before the call to
context_alloc(). If we had an integer overflow inside that function
then it would lead to an immediate crash.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Otherwise replacing the multipath target with the error target fails:
device-mapper: ioctl: can't change device type after initial table load.
The error target was mistakenly considered to be target type
DM_TYPE_REQUEST_BASED rather than DM_TYPE_MQ_REQUEST_BASED even if the
target it was to replace was of type DM_TYPE_MQ_REQUEST_BASED.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
For blk-mq request-based DM the responsibility of allocating a cloned
request is transfered from DM core to the target type. Doing so
enables the cloned request to be allocated from the appropriate
blk-mq request_queue's pool (only the DM target, e.g. multipath, can
know which block device to send a given cloned request to).
Care was taken to preserve compatibility with old-style block request
completion that requires request-based DM _not_ acquire the clone
request's queue lock in the completion path. As such, there are now 2
different request-based DM target_type interfaces:
1) the original .map_rq() interface will continue to be used for
non-blk-mq devices -- the preallocated clone request is passed in
from DM core.
2) a new .clone_and_map_rq() and .release_clone_rq() will be used for
blk-mq devices -- blk_get_request() and blk_put_request() are used
respectively from these hooks.
dm_table_set_type() was updated to detect if the request-based target is
being stacked on blk-mq devices, if so DM_TYPE_MQ_REQUEST_BASED is set.
DM core disallows switching the DM table's type after it is set. This
means that there is no mixing of non-blk-mq and blk-mq devices within
the same request-based DM table.
[This patch was started by Keith and later heavily modified by Mike]
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
For blk-mq request-based DM the responsibility of allocating a cloned
request will be transfered from DM core to the target type.
To prepare for conditionally using this new model the original
request's 'special' now points to the dm_rq_target_io because the
clone is allocated later in the block layer rather than in DM core.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Switch to having request-based DM enqueue all prep'ed requests into work
processed by another thread. This allows request-based DM to invoke
block APIs that assume interrupt enabled context (e.g. blk_get_request)
and is a prerequisite for adding blk-mq support to request-based DM.
The new kernel thread is only initialized for request-based DM devices.
multipath_map() is now always in irq enabled context so change multipath
spinlock (m->lock) locking to always disable interrupts.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Request-based DM support for blk-mq devices requires that
dm_rq_target_io structures not be allocated with an embedded request
structure. The request-based DM target (e.g. dm-multipath) must
allocate the request from the blk-mq devices' request_queue using
blk_get_request().
The unfortunate side-effect of this change is old-style request-based DM
support will no longer use contiguous memory for the dm_rq_target_io and
request structures for each clone.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit febf715 ("block: require blk_rq_prep_clone() be given an
initialized clone request") introduced a regression by calling
blk_rq_init() on the original request rather than the clone
request that is passed to setup_clone().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fixes: febf71588c ("block: require blk_rq_prep_clone() be given an initialized clone request")
Signed-off-by: Jens Axboe <axboe@fb.com>
After each call to rdev_dec_pending() we should wakeup the
md thread if the device is found to be faulty.
Otherwise we'll incur heavy delays on failing devices.
Signed-off-by: Neil Brown <nfbrown@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Rather than using mddev_lock() to take the reconfig_mutex
when writing to any md sysfs file, we only take mddev_lock()
in the particular _store() functions that require it.
Admittedly this is most, but it isn't all.
This also allows us to remove special-case handling for new_dev_store
(in md_attr_store).
Signed-off-by: NeilBrown <neilb@suse.de>
The one which is not inline (mddev_unlock) gets EXPORTed.
This makes the locking available to personality modules so that it
doesn't have to be imposed upon them.
Signed-off-by: NeilBrown <neilb@suse.de>
There are interdependencies between these two sysfs attributes
and whether a resync is currently running.
Rather than depending on reconfig_mutex to ensure no races when
testing these interdependencies are met, use the spinlock.
This will allow the mutex to be remove from protecting this
code in a subsequent patch.
Signed-off-by: NeilBrown <neilb@suse.de>
There isn't really much room for races with ->safemode_delay.
But as I am trying to clean up any racy code and will soon
be removing reconfig_mutex protection from most _store()
functions:
- only set mddev->safemode_delay once, to ensure no code
can see an intermediate value
- use safemode_timer to call md_safemode_timeout() rather than
calling it directly, to ensure it never races with itself.
Signed-off-by: NeilBrown <neilb@suse.de>
It makes more sense to report bitmap_info->file, rather than
bitmap->file (the later is only available once the array is
active).
With that change, use mddev->lock to protect bitmap_info being
set to NULL, and we can call get_bitmap_file() without taking
the mutex.
Signed-off-by: NeilBrown <neilb@suse.de>
1/ delay setting mddev->bitmap_info.file until 'f' looks
usable, so we don't have to unset it.
2/ Don't allow bitmap file to be set if bitmap_info.file
is already set.
Signed-off-by: NeilBrown <neilb@suse.de>
'buf' is only used because d_path fills from the end of the
buffer instead of from the start.
We don't need a separate buf to handle that, we just need to use
memmove() to move the string to the start.
Signed-off-by: NeilBrown <neilb@suse.de>
No rdev attributes need locking for 'show', though
state_show() might benefit from ensuring it sees a
consistent set of flags.
None even use rdev->mddev, so testing for it isn't really
needed and it certainly doesn't need to be held constant.
So improve state_show() and remove the locking.
Signed-off-by: NeilBrown <neilb@suse.de>
Most attributes can be read safely without any locking.
A race might lead to a slightly out-dated value, but nothing wrong.
We already have locking in some places where needed.
All that remains is can_clear_show(), behind_writes_used_show()
and action_show() which are easily fixed.
Signed-off-by: NeilBrown <neilb@suse.de>
It is important that mddev->private isn't freed while
a sysfs attribute function is accessing it.
So use mddev->lock to protect the setting of ->private to NULL, and
take that lock when checking ->private for NULL and de-referencing it
in the sysfs access functions.
This only applies to the read ('show') side of access. Write
access will be handled separately.
Signed-off-by: NeilBrown <neilb@suse.de>
The only access in md_seq_show that could suffer from races
not protected by ->lock is walking the rdev list.
This can receive sufficient protection from 'rcu'.
So use rdev_for_each_rcu() and get rid of mddev_lock().
Now reading /proc/mdstat will never block in md_seq_show.
Signed-off-by: NeilBrown <neilb@suse.de>
1/ Another live lock, needs backporting
2/ work-around false positive with new warnings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=qYoP
-----END PGP SIGNATURE-----
Merge tag 'md/3.19-fixes' of git://neil.brown.name/md
Pull two fixes for md from Neil Brown:
- Another live lock, needs backporting
- work-around false positive with new warnings.
* tag 'md/3.19-fixes' of git://neil.brown.name/md:
md/bitmap: fix a might_sleep() warning.
md/raid5: fix another livelock caused by non-aligned writes.
->pers is already protected by ->reconfig_mutex, and
cannot possibly change when there are threads running or
outstanding IO.
However there are some places where we access ->pers
not in a thread or IO context, and where ->reconfig_mutex
is unnecessarily heavy-weight: level_show and md_seq_show().
So protect all changes, and those accesses, with ->lock.
This is a step toward taking those accesses out from under
reconfig_mutex.
[Fixed missing "mddev->pers" -> "pers" conversion, thanks to
Dan Carpenter <dan.carpenter@oracle.com>]
Signed-off-by: NeilBrown <neilb@suse.de>
Gather all the changes that can happen atomically and might
be relevant to other code into one place. This will
make it easier to refine the locking.
Note that this puts quite a few things between mddev_detach()
and ->free(). Enabling this was the point of some recent patches.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that the ->stop function only frees the private data,
rename is accordingly.
Also pass in the private pointer as an arg rather than using
mddev->private. This flexibility will be useful in level_store().
Finally, don't clear ->private. It doesn't make sense to clear
it seeing that isn't what we free, and it is no longer necessary
to clear ->private (it was some time ago before ->to_remove was
introduced).
Setting ->to_remove in ->free() is a bit of a wart, but not a
big problem at the moment.
Signed-off-by: NeilBrown <neilb@suse.de>
Each md personality has a 'stop' operation which does two
things:
1/ it finalizes some aspects of the array to ensure nothing
is accessing the ->private data
2/ it frees the ->private data.
All the steps in '1' can apply to all arrays and so can be
performed in common code.
This is useful as in the case where we change the personality which
manages an array (in level_store()), it would be helpful to do
step 1 early, and step 2 later.
So split the 'step 1' functionality out into a new mddev_detach().
Signed-off-by: NeilBrown <neilb@suse.de>
The use of 'rcu' to protect accesses to ->private_data so that
the ->private_data could be updated predates the introduction
of mddev_suspend/mddev_resume.
These are a cleaner mechanism for providing stability while
swapping in a new ->private data - it is used by level_store()
to support changing of raid levels.
So get rid of the RCU stuff and just use mddev_suspend, mddev_resume.
As these function call ->quiesce(), we add an empty function for
linear just like for raid0.
Signed-off-by: NeilBrown <neilb@suse.de>
There is no locking around calls to merge_bvec_fn(), so
it is possible that calls which coincide with a level (or personality)
change could go wrong.
So create a central dispatch point for these functions and use
rcu_read_lock().
If the array is suspended, reject any merge that can be rejected.
If not, we know it is safe to call the function.
Signed-off-by: NeilBrown <neilb@suse.de>
There is currently no locking around calls to the 'congested'
bdi function. If called at an awkward time while an array is
being converted from one level (or personality) to another, there
is a tiny chance of running code in an unreferenced module etc.
So add a 'congested' function to the md_personality operations
structure, and call it with appropriate locking from a central
'mddev_congested'.
When the array personality is changing the array will be 'suspended'
so no IO is processed.
If mddev_congested detects this, it simply reports that the
array is congested, which is a safe guess.
As mddev_suspend calls synchronize_rcu(), mddev_congested can
avoid races by included the whole call inside an rcu_read_lock()
region.
This require that the congested functions for all subordinate devices
can be run under rcu_lock. Fortunately this is the case.
Signed-off-by: NeilBrown <neilb@suse.de>
This lock is used for (slightly) more than helping with writing
superblocks, and it will soon be extended further. So the
name is inappropriate.
Also, the _irq variant hasn't been needed since 2.6.37 as it is
never taking from interrupt or bh context.
So:
-rename write_lock to lock
-document what it protects
-remove _irq ... except in md_flush_request() as there
is no wait_event_lock() (with no _irq). This can be
cleaned up after appropriate changes to wait.h.
Signed-off-by: NeilBrown <neilb@suse.de>
That last condition is unclear and over cautious.
There are two related issues here.
If a partial write is destined for a missing device, then
either RMW or RCW can work. We must read all the available
block. Only then can the missing blocks be calculated, and
then the parity update performed.
If RMW is not an option, then there is a complication even
without partial writes. If we would need to read a missing
device to perform the reconstruction, then we must first read every
block so the missing device data can be computed.
This is the case for RAID6 (Which currently does not support
RMW) and for times when we don't trust the parity (after a crash)
and so are in the process of resyncing it.
So make these two cases more clear and separate, and perform
the relevant tests more thoroughly.
Signed-off-by: NeilBrown <neilb@suse.de>
Both the last two cases are only relevant if something has failed and
something needs to be written (but not over-written), and if it is OK
to pre-read blocks at this point. So factor out those tests and
explain them.
Signed-off-by: NeilBrown <neilb@suse.de>
Some of the conditions in need_this_block have very straight
forward motivation. Separate those out and document them.
Signed-off-by: NeilBrown <neilb@suse.de>
fetch_block() has a very large and hard to read 'if' condition.
Separate it into its own function so that it can be
made more readable.
Signed-off-by: NeilBrown <neilb@suse.de>
67f455486d introduced a call to
md_wakeup_thread() when adding to the delayed_list. However the md
thread is woken up unconditionally just below.
Remove the unnecessary wakeup call.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 8eb23b9f35
sched: Debug nested sleeps
causes false-positive warnings in RAID5 code.
This annotation removes them and adds a comment
explaining why there is no real problem.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a non-page-aligned write is destined for a device which
is missing/faulty, we can deadlock.
As the target device is missing, a read-modify-write cycle
is not possible.
As the write is not for a full-page, a recontruct-write cycle
is not possible.
This should be handled by logic in fetch_block() which notices
there is a non-R5_OVERWRITE write to a missing device, and so
loads all blocks.
However since commit 67f455486d, that code requires
STRIPE_PREREAD_ACTIVE before it will active, and those circumstances
never set STRIPE_PREREAD_ACTIVE.
So: in handle_stripe_dirtying, if neither rmw or rcw was possible,
set STRIPE_DELAYED, which will cause STRIPE_PREREAD_ACTIVE be set
after a suitable delay.
Fixes: 67f455486d
Cc: stable@vger.kernel.org (v3.16+)
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Prepare to allow blk_rq_prep_clone() to accept clone requests that were
allocated from blk-mq request queues. As such the blk_rq_prep_clone()
caller must first initialize the clone request.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
You can't modify the metadata in these modes. It's better to fail these
messages immediately than let the block-manager deny write locks on
metadata blocks. Otherwise these failed metadata changes will trigger
'needs_check' to get set in the metadata superblock -- requiring repair
using the thin_check utility.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Commit 9b1cc9f251 ("dm cache: share cache-metadata object across
inactive and active DM tables") mistakenly ignored the use of ERR_PTR
returns. Restore missing IS_ERR checks and ERR_PTR returns where
appropriate.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Commit ffcc393641 ("dm: enhance internal suspend and resume interface")
attempted to handle multiple internal suspends on the same device, but
it did that incorrectly. When these functions are called in this order
on the same device the device is no longer suspended, but it should be:
dm_internal_suspend_noflush
dm_internal_suspend_noflush
dm_internal_resume
Fix this bug by maintaining an 'internal_suspend_count' and resuming
the device when this count drops to zero.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Introduce a new variable to count the number of allocated migration
structures. The existing variable cache->nr_migrations became
overloaded. It was used to:
i) track of the number of migrations in flight for the purposes of
quiescing during suspend.
ii) to estimate the amount of background IO occuring.
Recent discard changes meant that REQ_DISCARD bios are processed with
a migration. Discards are not background IO so nr_migrations was not
incremented. However this could cause quiescing to complete early.
(i) is now handled with a new variable cache->nr_allocated_migrations.
cache->nr_migrations has been renamed cache->nr_io_migrations.
cleanup_migration() is now called free_io_migration(), since it
decrements that variable.
Also, remove the unused cache->next_migration variable that got replaced
with with prealloc_structs a while ago.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
If a DM table is reloaded with an inactive table when the device is not
suspended (normal procedure for LVM2), then there will be two dm-bufio
objects that can diverge. This can lead to a situation where the
inactive table uses bufio to read metadata at the same time the active
table writes metadata -- resulting in the inactive table having stale
metadata buffers once it is promoted to the active table slot.
Fix this by using reference counting and a global list of cache metadata
objects to ensure there is only one metadata object per metadata device.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Pull RCU updates from Paul E. McKenney:
- Documentation updates.
- Miscellaneous fixes.
- Preemptible-RCU fixes, including fixing an old bug in the
interaction of RCU priority boosting and CPU hotplug.
- SRCU updates.
- RCU CPU stall-warning updates.
- RCU torture-test updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
SRCU is not necessary to be compiled by default in all cases. For tinification
efforts not compiling SRCU unless necessary is desirable.
The current patch tries to make compiling SRCU optional by introducing a new
Kconfig option CONFIG_SRCU which is selected when any of the components making
use of SRCU are selected.
If we do not select CONFIG_SRCU, srcu.o will not be compiled at all.
text data bss dec hex filename
2007 0 0 2007 7d7 kernel/rcu/srcu.o
Size of arch/powerpc/boot/zImage changes from
text data bss dec hex filename
831552 64180 23944 919676 e087c arch/powerpc/boot/zImage : before
829504 64180 23952 917636 e0084 arch/powerpc/boot/zImage : after
so the savings are about ~2000 bytes.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
CC: Josh Triplett <josh@joshtriplett.org>
CC: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: resolve conflict due to removal of arch/ia64/kvm/Kconfig. ]
In bio-based DM's clone_endio(), when target_type doesn't implement
.end_io (e.g. linear) r will be always be initialized 0. So if a
WRITE SAME bio fails WRITE SAME will not be disabled as intended.
Fix this by initializing r to error, rather than 0, in clone_endio().
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fixes: 7eee4ae2db ("dm: disable WRITE SAME if it fails")
Cc: stable@vger.kernel.org
Commit 80e96c5484 ("dm thin: do not allow thin device activation
while pool is suspended") delayed the initialization of a new thin
device's refcount and completion until after this new thin was added
to the pool's active_thins list and the pool lock is released. This
opens a race with a worker thread that walks the list and calls
thin_get/put, noticing that the refcount goes to 0 and calling
complete, freezing up the system and giving the oops below:
kernel: BUG: unable to handle kernel NULL pointer dereference at (null)
kernel: IP: [<ffffffff810d360b>] __wake_up_common+0x2b/0x90
kernel: Call Trace:
kernel: [<ffffffff810d3683>] __wake_up_locked+0x13/0x20
kernel: [<ffffffff810d3dc7>] complete+0x37/0x50
kernel: [<ffffffffa0595c50>] thin_put+0x20/0x30 [dm_thin_pool]
kernel: [<ffffffffa059aab7>] do_worker+0x667/0x870 [dm_thin_pool]
kernel: [<ffffffff816a8a4c>] ? __schedule+0x3ac/0x9a0
kernel: [<ffffffff810b1aef>] process_one_work+0x14f/0x400
kernel: [<ffffffff810b206b>] worker_thread+0x6b/0x490
kernel: [<ffffffff810b2000>] ? rescuer_thread+0x260/0x260
kernel: [<ffffffff810b6a7b>] kthread+0xdb/0x100
kernel: [<ffffffff810b69a0>] ? kthread_create_on_node+0x170/0x170
kernel: [<ffffffff816ad7ec>] ret_from_fork+0x7c/0xb0
kernel: [<ffffffff810b69a0>] ? kthread_create_on_node+0x170/0x170
Set the thin device's initial refcount and initialize the completion
before adding it to the pool's active_thins list in thin_ctr().
Signed-off-by: Marc Dionne <marc.dionne@your-file-system.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Discard bios and thin device deletion have the potential to release data
blocks. If the thin-pool is in out-of-data-space mode, and blocks were
released, transition the thin-pool back to full write mode.
The correct time to do this is just after the thin-pool metadata commit.
It cannot be done before the commit because the space maps will not
allow immediate reuse of the data blocks in case there's a rollback
following power failure.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
When the pool was in PM_OUT_OF_SPACE mode its process_prepared_discard
function pointer was incorrectly being set to
process_prepared_discard_passdown rather than process_prepared_discard.
This incorrect function pointer meant the discard was being passed down,
but not effecting the mapping. As such any discard that was issued, in
an attempt to reclaim blocks, would not successfully free data space.
Reported-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ar2y
-----END PGP SIGNATURE-----
Merge tag 'md/3.19' of git://neil.brown.name/md
Pull md updates from Neil Brown:
"Three fixes for md.
I did have a largish set of locking changes queued, but late testing
showed they weren't quite as stable as I thought and while I fixed
what I found, I decided it safer to delay them a release ...
particularly as I'll be AFK for a few weeks. So expect a larger batch
next time :-)"
* tag 'md/3.19' of git://neil.brown.name/md:
md: Check MD_RECOVERY_RUNNING as well as ->sync_thread.
md: fix semicolon.cocci warnings
md/raid5: fetch_block must fetch all the blocks handle_stripe_dirtying wants.
Pull block layer driver updates from Jens Axboe:
- NVMe updates:
- The blk-mq conversion from Matias (and others)
- A stack of NVMe bug fixes from the nvme tree, mostly from Keith.
- Various bug fixes from me, fixing issues in both the blk-mq
conversion and generic bugs.
- Abort and CPU online fix from Sam.
- Hot add/remove fix from Indraneel.
- A couple of drbd fixes from the drbd team (Andreas, Lars, Philipp)
- With the generic IO stat accounting from 3.19/core, converting md,
bcache, and rsxx to use those. From Gu Zheng.
- Boundary check for queue/irq mode for null_blk from Matias. Fixes
cases where invalid values could be given, causing the device to hang.
- The xen blkfront pull request, with two bug fixes from Vitaly.
* 'for-3.19/drivers' of git://git.kernel.dk/linux-block: (56 commits)
NVMe: fix race condition in nvme_submit_sync_cmd()
NVMe: fix retry/error logic in nvme_queue_rq()
NVMe: Fix FS mount issue (hot-remove followed by hot-add)
NVMe: fix error return checking from blk_mq_alloc_request()
NVMe: fix freeing of wrong request in abort path
xen/blkfront: remove redundant flush_op
xen/blkfront: improve protection against issuing unsupported REQ_FUA
NVMe: Fix command setup on IO retry
null_blk: boundary check queue_mode and irqmode
block/rsxx: use generic io stats accounting functions to simplify io stat accounting
md: use generic io stats accounting functions to simplify io stat accounting
drbd: use generic io stats accounting functions to simplify io stat accounting
md/bcache: use generic io stats accounting functions to simplify io stat accounting
NVMe: Update module version major number
NVMe: fail pci initialization if the device doesn't have any BARs
NVMe: add ->exit_hctx() hook
NVMe: make setup work for devices that don't do INTx
NVMe: enable IO stats by default
NVMe: nvme_submit_async_admin_req() must use atomic rq allocation
NVMe: replace blk_put_request() with blk_mq_free_request()
...
A recent change to md started the ->sync_thread from a asynchronously
from a work_queue rather than synchronously. This means that there
can be a small window between the time when MD_RECOVERY_RUNNING is set
and when ->sync_thread is set.
So code that checks ->sync_thread might now conclude that the thread
has not been started and (because a lock is held) will not be started.
That is no longer the case.
Most of those places are best fixed by testing MD_RECOVERY_RUNNING
as well. To make this completely reliable, we wake_up(&resync_wait)
after clearing that flag as well as after clearing ->sync_thread.
Other places are better served by flushing the relevant workqueue
to ensure that that if the sync thread was starting, it has now
started. This is particularly best if we are about to stop the
sync thread.
Fixes: ac05f25669
Signed-off-by: NeilBrown <neilb@suse.de>
performance requirements that were requested by the Gluster
distributed filesystem. Specifically, dm-thinp now takes care to
aggregate IO that will be issued to the same thinp block before
issuing IO to the underlying devices. This really helps improve
performance on HW RAID6 devices that have a writeback cache because it
avoids RMW in the HW RAID controller.
- Some stable fixes: fix leak in DM bufio if integrity profiles were
enabled, use memzero_explicit in DM crypt to avoid any potential for
information leak, and a DM cache fix to properly mark a cache block
dirty if it was promoted to the cache via the overwrite optimization.
- A few simple DM persistent data library fixes
- DM cache multiqueue policy block promotion improvements.
- DM cache discard improvements that take advantage of range
(multiblock) discard support in the DM bio-prison. This allows for
much more efficient bulk discard processing (e.g. when mkfs.xfs
discards the entire device).
- Some small optimizations in DM core and RCU deference cleanups
- DM core changes to suspend/resume code to introduce the new internal
suspend/resume interface that the DM thin-pool target now uses to
suspend/resume active thin devices when the thin-pool must
suspend/resume. This avoids forcing userspace to track all active
thin volumes in a thin-pool when the thin-pool is suspended for the
purposes of metadata or data space resize.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhcvVAAoJEMUj8QotnQNaB78H+wSA6sDJGOhc6e1KlWoFh4Hx
hTmwm/O8Fxrp9StO3NPlcv9l+l9FX9pGzN/lo3OsxgWMTs/vLTKZ5SAe3/YT3/b9
6SFC7pC70+glakgMhhXWRvoeSEQC1OWb5BuvOF8irl2n+7B9NAn/zHd9pgpmyWHp
nBXK2GJBMzVSiI47NMjo2n6007LgQq0xxSJ9luwdrpwjDqD1d406DrhzbHou5H2Y
b8XJGQzUy0GZCX8ycwPVXo9svp2Bc+XajVcgOj5Qg7s2uV5car8NN7TxhSOKSXn2
VpiSyEa2MLHAbFuWtGs8XO98z/m5JlGf1eIgRO4s7w59URgpzdxOHXLlAoyqIGw=
=opXi
-----END PGP SIGNATURE-----
Merge tag 'dm-3.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- Significant DM thin-provisioning performance improvements to meet
performance requirements that were requested by the Gluster
distributed filesystem.
Specifically, dm-thinp now takes care to aggregate IO that will be
issued to the same thinp block before issuing IO to the underlying
devices. This really helps improve performance on HW RAID6 devices
that have a writeback cache because it avoids RMW in the HW RAID
controller.
- Some stable fixes: fix leak in DM bufio if integrity profiles were
enabled, use memzero_explicit in DM crypt to avoid any potential for
information leak, and a DM cache fix to properly mark a cache block
dirty if it was promoted to the cache via the overwrite optimization.
- A few simple DM persistent data library fixes
- DM cache multiqueue policy block promotion improvements.
- DM cache discard improvements that take advantage of range
(multiblock) discard support in the DM bio-prison. This allows for
much more efficient bulk discard processing (e.g. when mkfs.xfs
discards the entire device).
- Some small optimizations in DM core and RCU deference cleanups
- DM core changes to suspend/resume code to introduce the new internal
suspend/resume interface that the DM thin-pool target now uses to
suspend/resume active thin devices when the thin-pool must
suspend/resume.
This avoids forcing userspace to track all active thin volumes in a
thin-pool when the thin-pool is suspended for the purposes of
metadata or data space resize.
* tag 'dm-3.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (49 commits)
dm crypt: use memzero_explicit for on-stack buffer
dm space map metadata: fix sm_bootstrap_get_count()
dm space map metadata: fix sm_bootstrap_get_nr_blocks()
dm bufio: fix memleak when using a dm_buffer's inline bio
dm cache: fix spurious cell_defer when dealing with partial block at end of device
dm cache: dirty flag was mistakenly being cleared when promoting via overwrite
dm cache: only use overwrite optimisation for promotion when in writeback mode
dm cache: discard block size must be a multiple of cache block size
dm cache: fix a harmless race when working out if a block is discarded
dm cache: when reloading a discard bitset allow for a different discard block size
dm cache: fix some issues with the new discard range support
dm array: if resizing the array is a noop set the new root to the old one
dm: use rcu_dereference_protected instead of rcu_dereference
dm thin: fix pool_io_hints to avoid looking at max_hw_sectors
dm thin: suspend/resume active thin devices when reloading thin-pool
dm: enhance internal suspend and resume interface
dm thin: do not allow thin device activation while pool is suspended
dm: add presuspend_undo hook to target_type
dm: return earlier from dm_blk_ioctl if target doesn't implement .ioctl
dm thin: remove stale 'trim' message in block comment above pool_message
...
It is critical that fetch_block() and handle_stripe_dirtying()
are consistent in their analysis of what needs to be loaded.
Otherwise raid5 can wait forever for a block that won't be loaded.
Currently when writing to a RAID5 that is resyncing, to a location
beyond the resync offset, handle_stripe_dirtying chooses a
reconstruct-write cycle, but fetch_block() assumes a
read-modify-write, and a lockup can happen.
So treat that case just like RAID6, just as we do in
handle_stripe_dirtying. RAID6 always does reconstruct-write.
This bug was introduced when the behaviour of handle_stripe_dirtying
was changed in 3.7, so the patch is suitable for any kernel since,
though it will need careful merging for some versions.
Cc: stable@vger.kernel.org (v3.7+)
Fixes: a7854487cd
Reported-by: Henry Cai <henryplusplus@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Use memzero_explicit to cleanup sensitive data allocated on stack
to prevent the compiler from optimizing and removing memset() calls.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
This function isn't right and it causes a static checker warning:
drivers/md/dm-thin.c:3016 maybe_resize_data_dev()
error: potentially using uninitialized 'sb_data_size'.
It should set "*count" and return zero on success the same as the
sm_metadata_get_nr_blocks() function does earlier.
Fixes: 3241b1d3e0 ('dm: add persistent data library')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When dm-bufio sets out to use the bio built into a struct dm_buffer to
issue an IO, it needs to call bio_reset after it's done with the bio
so that we can free things attached to the bio such as the integrity
payload. Therefore, inject our own endio callback to take care of
the bio_reset after calling submit_io's end_io callback.
Test case:
1. modprobe scsi_debug delay=0 dif=1 dix=199 ato=1 dev_size_mb=300
2. Set up a dm-bufio client, e.g. dm-verity, on the scsi_debug device
3. Repeatedly read metadata and watch kmalloc-192 leak!
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
We never bother caching a partial block that is at the back end of the
origin device. No cell ever gets locked, but the calling code was
assuming it was and trying to release it.
Now the code only releases if the cell has been set to a non NULL
value.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
If the incoming bio is a WRITE and completely covers a block then we
don't bother to do any copying for a promotion operation. Once this is
done the cache block and origin block will be different, so we need to
set it to 'dirty'.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Overwrite causes the cache block and origin blocks to diverge, which
is only allowed in writeback mode.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Otherwise the cache blocks may span two discard blocks, which we don't
handle when doing the discard lookup.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
It is more correct to hold the cell before checking the discard state.
These flags are only used as hints to the policy so this change will
have negligable effect.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The discard block size can change if the origin changes size or if an
old DM cache is upgraded from using a discard block size that was equal
to cache block size.
To fix this an extent of discarded blocks is established for the purpose
of translating the old discard block size to the new in-core discard
block size and set bits. The old (potentially huge) discard bitset is
left ondisk until it is re-written using the new in-core information on
the next successful DM cache shutdown.
Fixes: 7ae34e7778 ("dm cache: improve discard support")
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit 7ae34e777 ("dm cache: improve discard support") needed to also:
- discontinue having DM core split the discard bios on cache block
boundaries
- calculate the cache's discard_nr_blocks relative to the determined
discard_block_size rather than using oblock_to_dblock()
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This could've been quite bad (to return success but not update the new
root to point at the old) but in practice the only known consumer of the
dm array code is the DM cache target. And the DM cache target passes in
the same old root to array_resize() anyway.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use generic io stats accounting help functions (generic_{start,end}_io_acct)
to simplify io stat accounting.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Acked-by: Kent Overstreet <kmo@datera.io>
Signed-off-by: Jens Axboe <axboe@fb.com>
rcu_dereference() should be used in sections protected by rcu_read_lock.
For writers, holding some kind of mutex or lock,
rcu_dereference_protected() is the way to go, adding explicit lockdep
bits.
In __unbind(), we are the last user of this mapped device, so can use
the constant '1' instead of a lockdep_is_held(), not consistent with
other uses of rcu_dereference_protected() which use md->suspend_lock
mutex.
Reported-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 33423974bf ("dm: Use rcu_dereference() for accessing rcu pointer")
Cc: Pranith Kumar <bobby.prani@gmail.com>
[snitzer: allow lines longer than 80 columns, refine subject]
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Simplify the pool_io_hints code that works to establish a max_sectors
value that is a power-of-2 factor of the thin-pool's blocksize. The
biggest associated improvement is that the DM thin-pool is no longer
concerning itself with the data device's max_hw_sectors when adjusting
max_sectors.
This fixes the relative fragility of the original "dm thin: adjust
max_sectors_kb based on thinp blocksize" commit that only became
apparent when testing was performed using a DM thin-pool ontop of a
virtio_blk device. One proposed upstream patch detailed the problems
inherent in virtio_blk: https://lkml.org/lkml/2014/11/20/611
So even though virtio_blk incorrectly set its max_hw_sectors it actually
helped make it clear that we need DM thinp to be tolerant of any future
Linux driver that incorrectly sets max_hw_sectors.
We only need to be concerned with modifying the thin-pool device's
max_sectors limit if it is smaller than the thin-pool's blocksize. In
this case the value of max_sectors does become a limiting factor when
upper layers (e.g. filesystems) construct their bios. But if the
hardware can support IOs larger than the thin-pool's blocksize the user
is encouraged to adjust the thin-pool's data device's max_sectors
accordingly -- doing so will enable the thin-pool to inherit the
established user-defined max_sectors.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Before this change it was expected that userspace would first suspend
all active thin devices, reload/resize the thin-pool target, then resume
all active thin devices. Now the thin-pool suspend/resume will trigger
the suspend/resume of all active thins via appropriate calls to
dm_internal_suspend and dm_internal_resume.
Store the mapped_device for each thin device in struct thin_c to make
these calls possible.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Rename dm_internal_{suspend,resume} to dm_internal_{suspend,resume}_fast
-- dm-stats will continue using these methods to avoid all the extra
suspend/resume logic that is not needed in order to quickly flush IO.
Introduce dm_internal_suspend_noflush() variant that actually calls the
mapped_device's target callbacks -- otherwise target-specific hooks are
avoided (e.g. dm-thin's thin_presuspend and thin_postsuspend). Common
code between dm_internal_{suspend_noflush,resume} and
dm_{suspend,resume} was factored out as __dm_{suspend,resume}.
Update dm_internal_{suspend_noflush,resume} to always take and release
the mapped_device's suspend_lock. Also update dm_{suspend,resume} to be
aware of potential for DM_INTERNAL_SUSPEND_FLAG to be set and respond
accordingly by interruptibly waiting for the DM_INTERNAL_SUSPEND_FLAG to
be cleared. Add lockdep annotation to dm_suspend() and dm_resume().
The existing DM_SUSPEND_FLAG remains unchanged.
DM_INTERNAL_SUSPEND_FLAG is set by dm_internal_suspend_noflush() and
cleared by dm_internal_resume().
Both DM_SUSPEND_FLAG and DM_INTERNAL_SUSPEND_FLAG may be set if a device
was already suspended when dm_internal_suspend_noflush() was called --
this can be thought of as a "nested suspend". A "nested suspend" can
occur with legacy userspace dm-thin code that might suspend all active
thin volumes before suspending the pool for resize.
But otherwise, in the normal dm-thin-pool suspend case moving forward:
the thin-pool will have DM_SUSPEND_FLAG set and all active thins from
that thin-pool will have DM_INTERNAL_SUSPEND_FLAG set.
Also add DM_INTERNAL_SUSPEND_FLAG to status report. This new
DM_INTERNAL_SUSPEND_FLAG state is being reported to assist with
debugging (e.g. 'dmsetup info' will report an internally suspended
device accordingly).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Otherwise IO could be issued to the pool while it is suspended.
Care was taken to properly interlock between the thin and thin-pool
targets when accessing the pool's 'suspended' flag. The thin_ctr will
not add a new thin device to the pool's active_thins list if the pool is
susepended.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
The DM thin-pool target now must undo the changes performed during
pool_presuspend() so introduce presuspend_undo hook in target_type.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
This fixes a regression introduced in 3.13.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Fs49
-----END PGP SIGNATURE-----
Merge tag 'md/3.18-fix' of git://neil.brown.name/md
Pull md bugfix from Neil Brown:
"One fix for md for 3.18.
This fixes a regression introduced in 3.13"
* tag 'md/3.18-fix' of git://neil.brown.name/md:
md: Always set RECOVERY_NEEDED when clearing RECOVERY_FROZEN
md_check_recovery will skip any recovery and also clear
MD_RECOVERY_NEEDED if MD_RECOVERY_FROZEN is set.
So when we clear _FROZEN, we must set _NEEDED and ensure that
md_check_recovery gets run.
Otherwise we could miss out on something that is needed.
In particular, this can make it impossible to remove a
failed device from an array is the 'recovery-needed' processing
didn't happen.
Suitable for stable kernels since 3.13.
Cc: stable@vger.kernel.org (3.13+)
Reported-and-tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Fixes: 30b8feb730
Signed-off-by: NeilBrown <neilb@suse.de>
. stable fix for a dm-cache related bug in dm-btree walking code that
results from using very large fast device (e.g. 4T) with a very small
cache blocksize (e.g. 32K) -- this is a very uncommon configuration
. a couple fixes for dm-raid (one for stable and the other addresses a
crash in 3.18-rc1 code)
. stable fix for dm-thinp that addresses a very rare dm-bufio bug having
to do with memory reclaimation (via shrinker) when using dm-thinp
ontop of loopback devices
. fix a leak in dm-stripe target constructor's error path
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUY/p7AAoJEMUj8QotnQNaxPEIAJsmJC5ujQAIdm5yUxsOWruU
Y/36HbPvlmV8fgWqGyjaubBrzqgWry/yW/u/Sv9+9rE3Zh6JSVLVrCA6uZZ3Yr+j
HKYEPjm/O0zVJepfEDKtjG6dxeaql47+luwU1iP1bAYeZE3zmKn1oFT2GW5gTbxO
2n3MiN/dyX8v0cTw6r0O69luIAu93CSY0XDk+1ynfKlKKVmgcAUPvKuobF+yHXoF
Rd7KTqFoK6HgRhdUHvUQnCGDandZ9MHjt3oW9p3dv3ezvW1cNUARoVHMRGG6Awfu
WZkQ/VORDeaJT+bhjGfPIla1HbgxEKJrgzTUlpj+P6K2uPK2f6ECEyBpDLWKy9g=
=lkSu
-----END PGP SIGNATURE-----
Merge tag 'dm-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- stable fix for dm-thin that avoids normal IO racing with discard
- stable fix for a dm-cache related bug in dm-btree walking code that
results from using very large fast device (eg 4T) with a very small
cache blocksize (eg 32K) -- this is a very uncommon configuration
- a couple fixes for dm-raid (one for stable and the other addresses a
crash in 3.18-rc1 code)
- stable fix for dm-thinp that addresses a very rare dm-bufio bug
having to do with memory reclaimation (via shrinker) when using
dm-thinp ontop of loopback devices
- fix a leak in dm-stripe target constructor's error path
* tag 'dm-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm btree: fix a recursion depth bug in btree walking code
dm thin: grab a virtual cell before looking up the mapping
dm raid: fix inaccessible superblocks causing oops in configure_discard_support
dm raid: ensure superblock's size matches device's logical block size
dm bufio: change __GFP_IO to __GFP_FS in shrinker callbacks
dm stripe: fix potential for leak in stripe_ctr error path
As long as struct thin_c is in the list, anyone can grab a reference of
it. Consequently, we must wait for the reference count to drop to zero
*after* we remove the structure from the list, not before.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Loading and saving millions of block mappings takes time. We may as
well explain what's going on, and encourage people to use a larger
cache block size.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Safely allow the discard blocksize to be larger than the cache blocksize
by using the bio prison's range locking support. This also improves
discard performance considerly because larger discards are issued to the
dm-cache device. The discard blocksize was always intended to be
greater than the cache blocksize. But until now it wasn't implemented
safely.
Also, by safely restoring the ability to have discard blocksize larger
than cache blocksize we're able to significantly reduce the memory used
for the cache's discard bitset. Before, with a small discard blocksize,
the discard bitset could get quite large because its size is a function
of the discard blocksize and the origin device's size. For example,
previously, using a 32KB cache blocksize with a 40TB origin resulted in
1280MB of incore memory use for the discard bitset! Now, the discard
blocksize is scaled up accordingly to ensure the discard bitset is
capped at 2**14 bits, or 16KB.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This reverts commit d132cc6d9e because we
actually do want to allow the discard blocksize to be larger than the
cache blocksize. Further dm-cache discard changes will make this
possible.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This reverts commit 64ab346a36 because we
actually do want to allow the discard blocksize to be larger than the
cache blocksize. Further dm-cache discard changes will make this
possible.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Ranges will be placed in the same cell if they overlap.
Range locking is a prerequisite for more efficient multi-block discard
support in both the cache and thin-provisioning targets.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Before, if the user wanted sequential IO to be promoted to the cache
they'd have to set sequential_threshold to some nebulous large value.
Now, the user may easily disable sequential IO detection (and sequential
IO's implicit bypass of the cache) by setting sequential_threshold to 0.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Rather than maintaining a separate promote_threshold variable that we
periodically update we now use the hit count of the oldest clean
block. Also add a fudge factor to discourage demoting dirty blocks.
With some tests this has a sizeable difference, because the old code
was too eager to demote blocks. For example, device-mapper-test-suite's
git_extract_cache_quick test goes from taking 190 seconds, to 142
(linear on spindle takes 250).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When creating new devices dm_sync_table() calls
synchronize_rcu_expedited(), causing _all_ pending RCU pointers to be
flushed. This causes a latency overhead that is especially noticeable
when creating lots of devices.
And all of this is pointless as there are no old maps to be
disconnected, and hence no stale pointers which would need to be
cleared up.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Annotate the map field with __rcu since this is a rcu pointer which is checked
by sparse.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The map field in 'struct mapped_device' is an rcu pointer. Use rcu_dereference()
while accessing it.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Sort the cells in logical block order before processing each cell in
process_thin_deferred_cells(). This significantly improves the ondisk
layout on rotational storage, whereby improving read performance.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This use of direct submission in process_shared_bio() reduces latency
for submitting bios in the shared cell by avoiding adding those bios to
the deferred list and waiting for the next iteration of the worker.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This use of direct submission in process_prepared_mapping() reduces
latency for submitting bios in a cell by avoiding adding those bios to
the deferred list and waiting for the next iteration of the worker.
But this direct submission exposes the potential for a race between
releasing a cell and incrementing deferred set. Fix this by introducing
dm_cell_visit_release() and refactoring inc_remap_and_issue_cell()
accordingly.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This avoids dropping the cell, so increases the probability that other
bios will collect within the cell, rather than being passed individually
to the worker.
Also add required process_cell and process_discard_cell error handling
wrappers and set associated pool-mode function pointers accordingly.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When processing a discard bio, if the block is already quiesced do the
discard immediately rather than adding the mapping to a list for the
next iteration of the worker thread.
Discarding a fully provisioned 100G thin volume with 64k block size goes
from 860s to 95s with this change.
Clearly there's something wrong with the worker architecture, more
investigation needed.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Introduce thin_merge so that any additional constraints from the data
volume may be taken into account when determing the maximum number of
sectors that can be issued relative to the specified logical offset.
This is particularly important if/when the data volume is layered ontop
of a more sophisticated device (e.g. dm-raid or some other DM target).
Reviewed-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
These code changes do not introduce a functional change.
But bio_add_page() will never attempt to build up a bio larger than
queue_max_sectors(). Similarly, bio_get_nr_vecs() is also bound by
queue_max_sectors(). Therefore, there is no point in allowing
dm_merge_bvec() to answer "how many sectors can a bio have at this
offset?" with anything larger than queue_max_sectors(). Using
queue_max_sectors() rather than BIO_MAX_SECTORS serves to more
accurately convey the limits that are being imposed.
Also, use unlikely() to clarify the fact that the defensive code in
dm_merge_bvec() relative to max_size going negative shouldn't ever
happen -- if it does happen there is a bug in the block layer for
requesting larger than dm_merge_bvec()'s initial response for a given
offset. Also, update a comment in dm_merge_bvec() relative to
max_hw_sectors_kb. And fix empty newline whitespace.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Allows for filesystems to submit bios that are a factor of the thinp
blocksize, improving dm-thinp efficiency (particularly when the data
volume is RAID).
Also set io_min to max_sectors_kb if it is a factor of the thinp
blocksize.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Throttle IO based on the time it's taking the worker to do one loop.
There were reports of hung task timeouts occuring and it was observed
that the excessively long avgqu-sz (as reported by iostat) was
contributing to these hung tasks.
Throttling definitely helps dm-thinp perform better under heavy IO load
(without being detremental by being overzealous). It reduces avgqu-sz
drastically, e.g.: from 60K to ~6K, and even as low as 150 once metadata
is cached by bufio, when dirty_ratio=5, dirty_background_ratio=2. And
avgqu-sz stays at or below 30K even with dirty_ratio=20,
dirty_background_ratio=10.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
