This reverts commit 0bfc445dec.
When we change the permissions of regions mapped using contiguous
entries, the architecture requires us to follow a Break-Before-Make
strategy, breaking *all* associated entries before we can change any of
the following properties from the entries:
- presence of the contiguous bit
- output address
- attributes
- permissiones
Failure to do so can result in a number of problems (e.g. TLB conflict
aborts and/or erroneous results from TLB lookups).
See ARM DDI 0487A.k_iss10775, "Misprogramming of the Contiguous bit",
page D4-1762.
We do not take this into account when altering the permissions of kernel
segments in mark_rodata_ro(), where we change the permissions of live
contiguous entires one-by-one, leaving them transiently inconsistent.
This has been observed to result in failures on some fast model
configurations.
Unfortunately, we cannot follow Break-Before-Make here as we'd have to
unmap kernel text and data used to perform the sequence.
For the timebeing, revert commit 0bfc445dec so as to avoid issues
resulting from this misuse of the contiguous bit.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <Will.Deacon@arm.com>
Cc: stable@vger.kernel.org # v4.10
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 38fd94b027 ("arm64: Work around Falkor erratum 1003") tried to
work around a hardware erratum, but actually caused a system crash of
its own during switch_mm:
cpu_do_switch_mm+0x20/0x40
efi_virtmap_load+0x34/0x40
virt_efi_get_next_variable+0x64/0xc8
efivar_init+0x8c/0x348
efisubsys_init+0xd4/0x270
do_one_initcall+0x80/0x110
kernel_init_freeable+0x19c/0x240
kernel_init+0x10/0x100
ret_from_fork+0x10/0x50
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
In cpu_do_switch_mm, x1 contains the mm_struct pointer, which needs to
be preserved by the pre_ttbr0_update_workaround macro rather than passed
as a temporary.
This patch clobbers x2 and x3 instead, keeping the mm_struct intact
after the workaround has run.
Fixes: 38fd94b027 ("arm64: Work around Falkor erratum 1003")
Tested-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM64 DT updates are fairly small this time, only two new SoCs and a handful
of new machines get added, all of them similar to other hardware we already
support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner: MMC, USB
ARM Juno: Coresight, STM
Broadcom: NS2 GICv2m irqchip and PCIe
Marvell: Armada 3700 SPI, I2C, ethernet switch
Mediatek: MT8173 thermal
NXP i.MX: LS1046A thermal
Qualcomm: coresight on MSM8916, HDMI, WCNSS, SCM
Renesas: r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip: thermal, eDP, pinctrl enhancements
Samsung: TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier: SD reset, eMMC controller
ZTE: oppv2 cpufreq
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=glug
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"ARM64 DT updates are fairly small this time, only two new SoCs and a
handful of new machines get added, all of them similar to other
hardware we already support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards:
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64:
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K:
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner:
- MMC, USB
ARM Juno:
- Coresight, STM
Broadcom:
- NS2 GICv2m irqchip and PCIe
Marvell:
- Armada 3700 SPI, I2C, ethernet switch
Mediatek:
- MT8173 thermal
NXP i.MX:
- LS1046A thermal
Qualcomm:
- coresight on MSM8916, HDMI, WCNSS, SCM
Renesas:
- r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip:
- thermal, eDP, pinctrl enhancements
Samsung:
- TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier:
- SD reset, eMMC controller
ZTE:
- oppv2 cpufreq"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (110 commits)
arm64: dts: qcom: Add msm8916 CoreSight components
arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon
arm64: allwinner: add BananaPi-M64 support
arm64: allwinner: a64: add UART1 pin nodes
arm64: allwinner: pine64: add MMC support
arm64: allwinner: a64: Increase the MMC max frequency
arm64: allwinner: a64: Add MMC pinctrl nodes
arm64: allwinner: a64: Add MMC nodes
dt-bindings: clockgen: Add compatible string for LS1012A
Documentation: DT: add LS1012A compatible for SCFG and DCFG
Documentation: DT: Add entry for FSL LS1012A RDB, FRDM, QDS boards
arm64: dts: marvell: add generic-ahci compatibles for CP110 ahci
arm64: tegra: Use symbolic reset identifiers
arm64: dts: r8a7796: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: tidyup audma definition order
arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
arm64: dts: r8a7796: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add R-Car Gen3 thermal support
...
Defconfig additions, removals, etc. Almost all of them just turn on
drivers that we want on some platform, usually after the driver
has been merged into mainline.
There is now a new defconfig file for tango4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAWK8G/GCrR//JCVInAQLA3w/9GoJ+BvdlrieCdKj5ax9sDVMi11u5yDJP
NtoGM4RZlTFNr7bau8lbmJepH7K0ZLOWKfVisdvp3ykUszDkqqfRbOm7cmG8rQM7
K1BDDb0Mo0O6UgYAlgBM+zdhPEYZxSLYwSb9bAN4HlEkvuFsCwVURIN057IXP6zV
Hmb+a1nBmQAeXeVpxlBYQBV5HBXtbzNGUgXHAdBE6pO6uBC/8iNpzwaopP80eBr0
WXpqOe1ehW33ICeYKJPB13YwdfHNVnNuhMNTWGcCgBfXKBcSxWW72WsmmkO4sGFC
JtKz5revh1KySCyGmmi/sFKB0FIJkHF1VERQlmGRlh/6RBrLL5rqgXHr2HMgtbTy
rlFPPNWwl6DQl3xVg8UYg7Tz+k1HpHznUWaU4ng3MO8daHWnVEb06/TbO4SlDq+o
DEieUJDDTdAV01jGLuAU3AVOdBZKBY44NPp0d5EunzwaDPRY381XrECvlxxTuxq8
wxTTBYhL7rpt51d5ru59qwTqY6P0CiF4SeWNEth9Oh0Uyp0Vdj4Stkf4V6g647An
3jZg4NtKuFljzYVXkNH1//DTMNnCSUyaKbcbLzhV0D2aD5Pf2o2911tbu9Q/oEJT
PhISwCxsZ1tNccslmNGTr/G2hNihJqV7FNOrkfIEjddRzGhL1ot13BtUiEIZdA9Z
8F8BBga2ifI=
=noKQ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"Defconfig additions, removals, etc. Almost all of them just turn on
drivers that we want on some platform, usually after the driver has
been merged into mainline.
There is now a new defconfig file for tango4"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: multi_v7_defconfig: enable pstore configs
ARM: multi_v7_defconfig: enable some newly added crypto modules
ARM: davinci_all_defconfig: enable SATA modules
arm64: defconfig: enable CONFIG_MTD_NAND and CONFIG_MTD_NAND_DENALI_DT
arm64: defconfig: enable CONFIG_MTD_BLOCK
ARM: Import tango4_defconfig
ARM: omap2plus_defconfig: Enable support for RTC M41T80
ARM: omap2plus_defconfig: Enable support for micrell phys
ARM: vf610m4: defconfig: enable EXT4 filesystem
ARM: omap2plus_defconfig: Fix probe errors on UARTs 5 and 6
arm64: defconfig: Enable NUMA and NUMA_BALANCING
arm64: defconfig: enable SMMUv3 config
ARM: davinci_all_defconfig: enable iio
ARM: Keystone: Enable ARCH_HAS_RESET_CONTROLLER
ARM: configs: stm32: Add RTC support in STM32 defconfig
ARM: defconfig: qcom: add APQ8060 DragonBoard devices
ARM: qcom_defconfig: enable thermal sensors
ARM: qcom_defconfig: add ahci configs
ARM: qcom_defconfig: add pcie and atl1c ethernet configs
ARM: qcom_defconfig: add usb related configs
...
Changes to platform code for 64-bit ARM platforms, only trivial
stuff this time, a few defconfig changes to enable drivers, and
a new entry for the Cavium ThunderX2 platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ymi+
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit updates from Arnd Bergmann:
"Changes to platform code for 64-bit ARM platforms, only trivial stuff
this time, a few defconfig changes to enable drivers, and a new entry
for the Cavium ThunderX2 platform"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add Cavium ThunderX2 entry
arm64: add ARCH_THUNDER2 to defconfig
arm64: add THUNDER2 processor family
MAINTAINERS: Extend ARM/Mediatek SoC support section
arm64: defconfig: enable CONFIG_MMC_SDHCI_CADENCE
arm64: defconfig: enable XORv2 for Marvell Armada 7K/8K
200 commits and noteworthy changes for most architectures.
* ARM:
- GICv3 save/restore
- cache flushing fixes
- working MSI injection for GICv3 ITS
- physical timer emulation
* MIPS:
- various improvements under the hood
- support for SMP guests
- a large rewrite of MMU emulation. KVM MIPS can now use MMU notifiers
to support copy-on-write, KSM, idle page tracking, swapping, ballooning
and everything else. KVM_CAP_READONLY_MEM is also supported, so that
writes to some memory regions can be treated as MMIO. The new MMU also
paves the way for hardware virtualization support.
* PPC:
- support for POWER9 using the radix-tree MMU for host and guest
- resizable hashed page table
- bugfixes.
* s390: expose more features to the guest
- more SIMD extensions
- instruction execution protection
- ESOP2
* x86:
- improved hashing in the MMU
- faster PageLRU tracking for Intel CPUs without EPT A/D bits
- some refactoring of nested VMX entry/exit code, preparing for live
migration support of nested hypervisors
- expose yet another AVX512 CPUID bit
- host-to-guest PTP support
- refactoring of interrupt injection, with some optimizations thrown in
and some duct tape removed.
- remove lazy FPU handling
- optimizations of user-mode exits
- optimizations of vcpu_is_preempted() for KVM guests
* generic:
- alternative signaling mechanism that doesn't pound on tsk->sighand->siglock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJYral1AAoJEL/70l94x66DbNgH/Rx8YXuidFq2fe3RWOvld3RK
85OM/D5g38cTLpBE0/sJpcvX34iYN8U/l5foCZwpxB+83GHEk2Cr57JyfTogdaAJ
x8dBhHKQCA/HxSQUQLN6nFqRV+yT8WUR92Fhqx82+80BSen5Yzcfee/TDoW6T1IW
g8CYgX9FrRaGOX066ImAuUfdAdUVjyssfs9VttDTX+HiusPeuBPx/wsRe1ZEEPlH
vnltIJQb1ETV2GOZLUojKjzH6aZkjIl29XxjkYii9JTUornClG0DfW+5QT3uLrB5
gJ+G+Zmpsq8ZBx9jNDtAi7sFsoPY1Mzf+JPNCGXBra2sP2GrBAuXcxmgznRYltQ=
=8IIp
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"4.11 is going to be a relatively large release for KVM, with a little
over 200 commits and noteworthy changes for most architectures.
ARM:
- GICv3 save/restore
- cache flushing fixes
- working MSI injection for GICv3 ITS
- physical timer emulation
MIPS:
- various improvements under the hood
- support for SMP guests
- a large rewrite of MMU emulation. KVM MIPS can now use MMU
notifiers to support copy-on-write, KSM, idle page tracking,
swapping, ballooning and everything else. KVM_CAP_READONLY_MEM is
also supported, so that writes to some memory regions can be
treated as MMIO. The new MMU also paves the way for hardware
virtualization support.
PPC:
- support for POWER9 using the radix-tree MMU for host and guest
- resizable hashed page table
- bugfixes.
s390:
- expose more features to the guest
- more SIMD extensions
- instruction execution protection
- ESOP2
x86:
- improved hashing in the MMU
- faster PageLRU tracking for Intel CPUs without EPT A/D bits
- some refactoring of nested VMX entry/exit code, preparing for live
migration support of nested hypervisors
- expose yet another AVX512 CPUID bit
- host-to-guest PTP support
- refactoring of interrupt injection, with some optimizations thrown
in and some duct tape removed.
- remove lazy FPU handling
- optimizations of user-mode exits
- optimizations of vcpu_is_preempted() for KVM guests
generic:
- alternative signaling mechanism that doesn't pound on
tsk->sighand->siglock"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (195 commits)
x86/kvm: Provide optimized version of vcpu_is_preempted() for x86-64
x86/paravirt: Change vcp_is_preempted() arg type to long
KVM: VMX: use correct vmcs_read/write for guest segment selector/base
x86/kvm/vmx: Defer TR reload after VM exit
x86/asm/64: Drop __cacheline_aligned from struct x86_hw_tss
x86/kvm/vmx: Simplify segment_base()
x86/kvm/vmx: Get rid of segment_base() on 64-bit kernels
x86/kvm/vmx: Don't fetch the TSS base from the GDT
x86/asm: Define the kernel TSS limit in a macro
kvm: fix page struct leak in handle_vmon
KVM: PPC: Book3S HV: Disable HPT resizing on POWER9 for now
KVM: Return an error code only as a constant in kvm_get_dirty_log()
KVM: Return an error code only as a constant in kvm_get_dirty_log_protect()
KVM: Return directly after a failed copy_from_user() in kvm_vm_compat_ioctl()
KVM: x86: remove code for lazy FPU handling
KVM: race-free exit from KVM_RUN without POSIX signals
KVM: PPC: Book3S HV: Turn "KVM guest htab" message into a debug message
KVM: PPC: Book3S PR: Ratelimit copy data failure error messages
KVM: Support vCPU-based gfn->hva cache
KVM: use separate generations for each address space
...
Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and dwc
and xhci controllers, new device ids, new phy drivers, a new usb-serial
driver, and a few other minor changes in different USB drivers.
All have been in linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2lrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykh7ACffotTJvB/gwpuSIWh6qhA8KQ9mH8AnjlxMafv
b5b3vfOXJ8/N0Go25VwI
=7fqN
-----END PGP SIGNATURE-----
Merge tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and
dwc and xhci controllers, new device ids, new phy drivers, a new
usb-serial driver, and a few other minor changes in different USB
drivers.
All have been in linux-next for a long time with no reported issues"
* tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: cdc-wdm: remove logically dead code
USB: serial: keyspan: drop header file
USB: serial: io_edgeport: drop io-tables header file
usb: musb: add code comment for clarification
usb: misc: add USB251xB/xBi Hi-Speed Hub Controller Driver
usb: misc: usbtest: remove redundant check on retval < 0
USB: serial: upd78f0730: sort device ids
USB: serial: upd78f0730: add ID for EVAL-ADXL362Z
ohci-hub: fix typo in dbg_port macro
usb: musb: dsps: Manage CPPI 4.1 DMA interrupt in DSPS
usb: musb: tusb6010: Clean up tusb_omap_dma structure
usb: musb: cppi_dma: Clean up cppi41_dma_controller structure
usb: musb: cppi_dma: Clean up cppi structure
usb: musb: cppi41: Detect aborted transfers in cppi41_dma_callback()
usb: musb: dma: Add a DMA completion platform callback
drivers: usb: usbip: Add missing break statement to switch
usb: mtu3: remove redundant dev_err call in get_ssusb_rscs()
USB: serial: mos7840: fix another NULL-deref at open
USB: serial: console: clean up sanity checks
USB: serial: console: fix uninitialised spinlock
...
- Errata workarounds for Qualcomm's Falkor CPU
- Qualcomm L2 Cache PMU driver
- Qualcomm SMCCC firmware quirk
- Support for DEBUG_VIRTUAL
- CPU feature detection for userspace via MRS emulation
- Preliminary work for the Statistical Profiling Extension
- Misc cleanups and non-critical fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJYpIxqAAoJELescNyEwWM0xdwH/AsTYAXPZDMdRnrQUyV0Fd2H
/9pMzww6dHXEmCMKkImf++otUD6S+gTCJTsj7kEAXT5sZzLk27std5lsW7R9oPjc
bGQMalZy+ovLR1gJ6v072seM3In4xph/qAYOpD8Q0AfYCLHjfMMArQfoLa8Esgru
eSsrAgzVAkrK7XHi3sYycUjr9Hac9tvOOuQ3SaZkDz4MfFIbI4b43+c1SCF7wgT9
tQUHLhhxzGmgxjViI2lLYZuBWsIWsE+algvOe1qocvA9JEIXF+W8NeOuCjdL8WwX
3aoqYClC+qD/9+/skShFv5gM5fo0/IweLTUNIHADXpB6OkCYDyg+sxNM+xnEWQU=
=YrPg
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
- Errata workarounds for Qualcomm's Falkor CPU
- Qualcomm L2 Cache PMU driver
- Qualcomm SMCCC firmware quirk
- Support for DEBUG_VIRTUAL
- CPU feature detection for userspace via MRS emulation
- Preliminary work for the Statistical Profiling Extension
- Misc cleanups and non-critical fixes
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (74 commits)
arm64/kprobes: consistently handle MRS/MSR with XZR
arm64: cpufeature: correctly handle MRS to XZR
arm64: traps: correctly handle MRS/MSR with XZR
arm64: ptrace: add XZR-safe regs accessors
arm64: include asm/assembler.h in entry-ftrace.S
arm64: fix warning about swapper_pg_dir overflow
arm64: Work around Falkor erratum 1003
arm64: head.S: Enable EL1 (host) access to SPE when entered at EL2
arm64: arch_timer: document Hisilicon erratum 161010101
arm64: use is_vmalloc_addr
arm64: use linux/sizes.h for constants
arm64: uaccess: consistently check object sizes
perf: add qcom l2 cache perf events driver
arm64: remove wrong CONFIG_PROC_SYSCTL ifdef
ARM: smccc: Update HVC comment to describe new quirk parameter
arm64: do not trace atomic operations
ACPI/IORT: Fix the error return code in iort_add_smmu_platform_device()
ACPI/IORT: Fix iort_node_get_id() mapping entries indexing
arm64: mm: enable CONFIG_HOLES_IN_ZONE for NUMA
perf: xgene: Include module.h
...
Pull networking updates from David Miller:
"Highlights:
1) Support TX_RING in AF_PACKET TPACKET_V3 mode, from Sowmini
Varadhan.
2) Simplify classifier state on sk_buff in order to shrink it a bit.
From Willem de Bruijn.
3) Introduce SIPHASH and it's usage for secure sequence numbers and
syncookies. From Jason A. Donenfeld.
4) Reduce CPU usage for ICMP replies we are going to limit or
suppress, from Jesper Dangaard Brouer.
5) Introduce Shared Memory Communications socket layer, from Ursula
Braun.
6) Add RACK loss detection and allow it to actually trigger fast
recovery instead of just assisting after other algorithms have
triggered it. From Yuchung Cheng.
7) Add xmit_more and BQL support to mvneta driver, from Simon Guinot.
8) skb_cow_data avoidance in esp4 and esp6, from Steffen Klassert.
9) Export MPLS packet stats via netlink, from Robert Shearman.
10) Significantly improve inet port bind conflict handling, especially
when an application is restarted and changes it's setting of
reuseport. From Josef Bacik.
11) Implement TX batching in vhost_net, from Jason Wang.
12) Extend the dummy device so that VF (virtual function) features,
such as configuration, can be more easily tested. From Phil
Sutter.
13) Avoid two atomic ops per page on x86 in bnx2x driver, from Eric
Dumazet.
14) Add new bpf MAP, implementing a longest prefix match trie. From
Daniel Mack.
15) Packet sample offloading support in mlxsw driver, from Yotam Gigi.
16) Add new aquantia driver, from David VomLehn.
17) Add bpf tracepoints, from Daniel Borkmann.
18) Add support for port mirroring to b53 and bcm_sf2 drivers, from
Florian Fainelli.
19) Remove custom busy polling in many drivers, it is done in the core
networking since 4.5 times. From Eric Dumazet.
20) Support XDP adjust_head in virtio_net, from John Fastabend.
21) Fix several major holes in neighbour entry confirmation, from
Julian Anastasov.
22) Add XDP support to bnxt_en driver, from Michael Chan.
23) VXLAN offloads for enic driver, from Govindarajulu Varadarajan.
24) Add IPVTAP driver (IP-VLAN based tap driver) from Sainath Grandhi.
25) Support GRO in IPSEC protocols, from Steffen Klassert"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1764 commits)
Revert "ath10k: Search SMBIOS for OEM board file extension"
net: socket: fix recvmmsg not returning error from sock_error
bnxt_en: use eth_hw_addr_random()
bpf: fix unlocking of jited image when module ronx not set
arch: add ARCH_HAS_SET_MEMORY config
net: napi_watchdog() can use napi_schedule_irqoff()
tcp: Revert "tcp: tcp_probe: use spin_lock_bh()"
net/hsr: use eth_hw_addr_random()
net: mvpp2: enable building on 64-bit platforms
net: mvpp2: switch to build_skb() in the RX path
net: mvpp2: simplify MVPP2_PRS_RI_* definitions
net: mvpp2: fix indentation of MVPP2_EXT_GLOBAL_CTRL_DEFAULT
net: mvpp2: remove unused register definitions
net: mvpp2: simplify mvpp2_bm_bufs_add()
net: mvpp2: drop useless fields in mvpp2_bm_pool and related code
net: mvpp2: remove unused 'tx_skb' field of 'struct mvpp2_tx_queue'
net: mvpp2: release reference to txq_cpu[] entry after unmapping
net: mvpp2: handle too large value in mvpp2_rx_time_coal_set()
net: mvpp2: handle too large value handling in mvpp2_rx_pkts_coal_set()
net: mvpp2: remove useless arguments in mvpp2_rx_{pkts, time}_coal_set
...
CONFIG_SET_MODULE_RONX to the more sensible CONFIG_STRICT_KERNEL_RWX and
CONFIG_STRICT_MODULE_RWX.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>
iQIcBAABCgAGBQJYrJ2ZAAoJEIly9N/cbcAmb4UQAIDnJYF4xecUfxofypQwt7ey
DcR8SH+g/Rkm3v2bUOrVdlP333ePRUEs6C47PgYSLlKsZiQA3H6bsTILHJZGHZ3j
laNH4sjQ0j+Sr2rHXk8fLz3YpHHwIy49bfu2ERXFH92BMnTMCv1h9IWFgOMH+4y5
09n16TPHMUj1k0DGjHO/n03qLIKOo3Xy/Va5dhQ/6dGU4zR4KhOBnhLlG3IU7Atd
KTR+ba/qym7bDQbTezMuaajTiZctr6a45yBKDWu4Knu+ot2a7K7fYvfRT3YVb5SU
aTSYps7NKQbewcQSqNdek1zytoy2Ck7CH511e+3ypwNmao5KQwRgH7OX1pDEXyZv
rGDaVzKMTSddH23jLEKUbpR847Lza9+V3h5YtbMG8GgiCKs91Ec666iEE3NVZBO8
1hiiYhE2iDxi10B/EZZcn2gOt2JaB2m2GxWIrJOz4txtDAWbUYlhUpWEUynBTPQ0
cYBZVnge81awipZJTWUv57LyufnTnMSK3i8Q8t0woj4C7pFbPYfjnKCrgwTQyAvr
mD4uFBrgFb1lftbc3kfTdeoZmXerzvubsstWdr3rU3nsiJFzY1SwJZe8n0THyL4g
DzURFrj/8UXb32Kavysz6FTxFO9u87mJm6yqHn/Y3bEK7Y7cch/NYjRC9Q6dpH+4
ld9apHF6iRrqgf+x6oOh
=7KhR
-----END PGP SIGNATURE-----
Merge tag 'rodata-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull rodata updates from Kees Cook:
"This renames the (now inaccurate) DEBUG_RODATA and related
SET_MODULE_RONX configs to the more sensible STRICT_KERNEL_RWX and
STRICT_MODULE_RWX"
* tag 'rodata-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
arch: Rename CONFIG_DEBUG_RODATA and CONFIG_DEBUG_MODULE_RONX
arch: Move CONFIG_DEBUG_RODATA and CONFIG_SET_MODULE_RONX to be common
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJYrElpAAoJELDendYovxMvNFQH/RJU7lwDSf7rF7ZzFGvdcsfi
T4DDuowkYoJm2+GypoRVzZZ0lxJlxr0mNKPvgGDvuTogMY7pvjAf6B7/xCvTFsNU
UoO2I7ljgXxCXFRiXH50nAjS7PC2PFW3Qx+8XPIWeZmnUPeJi4Q43fiSloUt+a6l
JgS/autOCflGasR5MihCZXkvdVF81K6GuEd3hCh9GKZ/8RiwNPaY50vHnMv/hfqq
SJNRKOTSRXioYlTohLnjuPWHDMayRJEO48IXl3c7aNxDTkHjn78yaoPhJ7m+M0Bq
s2GyaQA4tCwADhP+tilmI5H1vFpt6w9x7O0dgWiSm7TB91lwfZOen2WhTPPp6L8=
=gktV
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.11-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"Xen features and fixes:
- a series from Boris Ostrovsky adding support for booting Linux as
Xen PVH guest
- a series from Juergen Gross streamlining the xenbus driver
- a series from Paul Durrant adding support for the new device model
hypercall
- several small corrections"
* tag 'for-linus-4.11-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/privcmd: add IOCTL_PRIVCMD_RESTRICT
xen/privcmd: Add IOCTL_PRIVCMD_DM_OP
xen/privcmd: return -ENOTTY for unimplemented IOCTLs
xen: optimize xenbus driver for multiple concurrent xenstore accesses
xen: modify xenstore watch event interface
xen: clean up xenbus internal headers
xenbus: Neaten xenbus_va_dev_error
xen/pvh: Use Xen's emergency_restart op for PVH guests
xen/pvh: Enable CPU hotplug
xen/pvh: PVH guests always have PV devices
xen/pvh: Initialize grant table for PVH guests
xen/pvh: Make sure we don't use ACPI_IRQ_MODEL_PIC for SCI
xen/pvh: Bootstrap PVH guest
xen/pvh: Import PVH-related Xen public interfaces
xen/x86: Remove PVH support
x86/boot/32: Convert the 32-bit pgtable setup code from assembly to C
xen/manage: correct return value check on xenbus_scanf()
x86/xen: Fix APIC id mismatch warning on Intel
xen/netback: set default upper limit of tx/rx queues to 8
xen/netfront: set default upper limit of tx/rx queues to 8
Eric and Willem reported that they recently saw random crashes when
JIT was in use and bisected this to 74451e66d5 ("bpf: make jited
programs visible in traces"). Issue was that the consolidation part
added bpf_jit_binary_unlock_ro() that would unlock previously made
read-only memory back to read-write. However, DEBUG_SET_MODULE_RONX
cannot be used for this to test for presence of set_memory_*()
functions. We need to use ARCH_HAS_SET_MEMORY instead to fix this;
also add the corresponding bpf_jit_binary_lock_ro() to filter.h.
Fixes: 74451e66d5 ("bpf: make jited programs visible in traces")
Reported-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Bisected-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there's no good way to test for the presence of
set_memory_ro/rw/x/nx() helpers implemented by archs such as
x86, arm, arm64 and s390.
There's DEBUG_SET_MODULE_RONX and DEBUG_RODATA, however both
don't really reflect that: set_memory_*() are also available
even when DEBUG_SET_MODULE_RONX is turned off, and DEBUG_RODATA
is set by parisc, but doesn't implement above functions. Thus,
add ARCH_HAS_SET_MEMORY that is selected by mentioned archs,
where generic code can test against this.
This also allows later on to move DEBUG_SET_MODULE_RONX out of
the arch specific Kconfig to define it only once depending on
ARCH_HAS_SET_MEMORY.
Suggested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Juno platforms have a programmable replicator splitting the trace output
to TPIU and ETR. Currently this is not being programmed as it is being
treated as a none-programmable replicator - which is the default
operational mode for these devices. The TPIU in the system is enabled by
default, and this combination is causing back-pressure in the trace
system resulting in overflows at the source.
Replaces the existing definition with one that defines the programmable
replicator, using the "qcom,coresight-replicator1x" driver that provides
the correct functionality for CoreSight programmable replicators.
Reviewed-and-Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The changes include:
* KVM PCIe/MSI passthrough support on ARM/ARM64
* Introduction of a core representation for individual hardware
iommus
* Support for IOMMU privileged mappings as supported by some
ARM IOMMUS
* 16-bit SID support for ARM-SMMUv2
* Stream table optimization for ARM-SMMUv3
* Various fixes and other small improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=5b3I
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU UPDATES from Joerg Roedel:
- KVM PCIe/MSI passthrough support on ARM/ARM64
- introduction of a core representation for individual hardware iommus
- support for IOMMU privileged mappings as supported by some ARM IOMMUS
- 16-bit SID support for ARM-SMMUv2
- stream table optimization for ARM-SMMUv3
- various fixes and other small improvements
* tag 'iommu-updates-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (61 commits)
vfio/type1: Fix error return code in vfio_iommu_type1_attach_group()
iommu: Remove iommu_register_instance interface
iommu/exynos: Make use of iommu_device_register interface
iommu/mediatek: Make use of iommu_device_register interface
iommu/msm: Make use of iommu_device_register interface
iommu/arm-smmu: Make use of the iommu_register interface
iommu: Add iommu_device_set_fwnode() interface
iommu: Make iommu_device_link/unlink take a struct iommu_device
iommu: Add sysfs bindings for struct iommu_device
iommu: Introduce new 'struct iommu_device'
iommu: Rename struct iommu_device
iommu: Rename iommu_get_instance()
iommu: Fix static checker warning in iommu_insert_device_resv_regions
iommu: Avoid unnecessary assignment of dev->iommu_fwspec
iommu/mediatek: Remove bogus 'select' statements
iommu/dma: Remove bogus dma_supported() implementation
iommu/ipmmu-vmsa: Restrict IOMMU Domain Geometry to 32-bit address space
iommu/vt-d: Don't over-free page table directories
iommu/vt-d: Tylersburg isoch identity map check is done too late.
iommu/vt-d: Fix some macros that are incorrectly specified in intel-iommu
...
Pull scheduler updates from Ingo Molnar:
"The main changes in this (fairly busy) cycle were:
- There was a class of scheduler bugs related to forgetting to update
the rq-clock timestamp which can cause weird and hard to debug
problems, so there's a new debug facility for this: which uncovered
a whole lot of bugs which convinced us that we want to keep the
debug facility.
(Peter Zijlstra, Matt Fleming)
- Various cputime related updates: eliminate cputime and use u64
nanoseconds directly, simplify and improve the arch interfaces,
implement delayed accounting more widely, etc. - (Frederic
Weisbecker)
- Move code around for better structure plus cleanups (Ingo Molnar)
- Move IO schedule accounting deeper into the scheduler plus related
changes to improve the situation (Tejun Heo)
- ... plus a round of sched/rt and sched/deadline fixes, plus other
fixes, updats and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (85 commits)
sched/core: Remove unlikely() annotation from sched_move_task()
sched/autogroup: Rename auto_group.[ch] to autogroup.[ch]
sched/topology: Split out scheduler topology code from core.c into topology.c
sched/core: Remove unnecessary #include headers
sched/rq_clock: Consolidate the ordering of the rq_clock methods
delayacct: Include <uapi/linux/taskstats.h>
sched/core: Clean up comments
sched/rt: Show the 'sched_rr_timeslice' SCHED_RR timeslice tuning knob in milliseconds
sched/clock: Add dummy clear_sched_clock_stable() stub function
sched/cputime: Remove generic asm headers
sched/cputime: Remove unused nsec_to_cputime()
s390, sched/cputime: Remove unused cputime definitions
powerpc, sched/cputime: Remove unused cputime definitions
s390, sched/cputime: Make arch_cpu_idle_time() to return nsecs
ia64, sched/cputime: Remove unused cputime definitions
ia64: Convert vtime to use nsec units directly
ia64, sched/cputime: Move the nsecs based cputime headers to the last arch using it
sched/cputime: Remove jiffies based cputime
sched/cputime, vtime: Return nsecs instead of cputime_t to account
sched/cputime: Complete nsec conversion of tick based accounting
...
Pull perf updates from Ingo Molnar:
"On the kernel side the main changes in this cycle were:
- Add Intel Kaby Lake CPU support (Srinivas Pandruvada)
- AMD uncore driver updates for fam17 (Janakarajan Natarajan)
- Intel/PT updates and core events optimizations and cleanups
(Alexander Shishkin)
- cgroups events fixes (David Carrillo-Cisneros)
- kprobes improvements (Masami Hiramatsu)
- ... plus misc fixes and updates.
On the tooling side the main changes were:
- Support clang build in tools/{perf,lib/{bpf,traceevent,api}} with
CC=clang, to, for instance, take advantage of better warnings
(Arnaldo Carvalho de Melo):
- Introduce the 'delta-abs' 'perf diff' compute method, that orders
the histogram entries by the absolute value of the percentage delta
for a function in two perf.data files, i.e. the functions that
changed the most (increase or decrease in samples) comes first
(Namhyung Kim)
- Add support for parsing Intel uncore vendor event files and add
uncore vendor events for the Intel server processors (Haswell,
Broadwell, IvyBridge), Xeon Phi (Knights Landing) and Broadwell DE
(Andi Kleen)
- Introduce 'perf ftrace' a perf front end to the kernel's ftrace
function and function_graph tracer, defaulting to the
"function_graph" tracer, more work will be done in reviving this
effort, forward porting it from its initial patch submission
(Namhyung Kim)
- Add 'e' and 'c' hotkeys to expand/collapse call chains for a single
hist entry in the 'perf report' and 'perf top' TUI (Jiri Olsa)
- Account thread wait time (off CPU time) separately: sleep, iowait
and preempt, based on the prev_state of the last event, show the
breakdown when using "perf sched timehist --state" (Namhyumg Kim)
- Add more triggers to switch the output file (perf.data.TIMESTAMP).
Now, in addition to switching to a different output file when
receiving a SIGUSR2, one can also specify file size and time based
triggers:
perf record -a --switch-output=signal
is equivalent to what we had before:
perf record -a --switch-output
While we can also ask for the file to be "sliced" by size, taking
into account that that will happen only when we get woken up by the
kernel, i.e. one has to take into account the --mmap-pages (the
size of the perf mmap ring buffer):
perf record -a --switch-output=2G
will break the perf.data output into multiple files limited to 2GB
of samples, right when generating the output.
For time based samples, alert() will be used, so to have 1 minute
limited perf.data output files:
perf record -a --switch-output=1m
(Jiri Olsa)
- Improve 'perf trace' (Arnaldo Carvalho de Melo)
- 'perf kallsyms' toy tool to look for extended symbol information on
the running kernel and demonstrate the machine/thread/symbol APIs
for use in other tools, such as 'perf probe' (Arnaldo Carvalho de
Melo)
- ... plus tons of other changes, see the shortlog and Git log for
details"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (131 commits)
perf tools: Add missing parse_events_error() prototype
perf pmu: Fix check for unset alias->unit array
perf tools: Be consistent on the type of map->symbols[] interator
perf intel pt decoder: clang has no -Wno-override-init
perf evsel: Do not put a variable sized type not at the end of a struct
perf probe: Avoid accessing uninitialized 'map' variable
perf tools: Do not put a variable sized type not at the end of a struct
perf record: Do not put a variable sized type not at the end of a struct
perf tests: Synthesize struct instead of using field after variable sized type
perf bench numa: Make sure dprintf() is not defined
Revert "perf bench futex: Sanitize numeric parameters"
tools lib subcmd: Make it an error to pass a signed value to OPTION_UINTEGER
tools: Set the maximum optimization level according to the compiler being used
tools: Suppress request for warning options not existent in clang
samples/bpf: Reset global variables
samples/bpf: Ignore already processed ELF sections
samples/bpf: Add missing header
perf symbols: dso->name is an array, no need to check it against NULL
perf tests record: No need to test an array against NULL
perf symbols: No need to check if sym->name is NULL
...
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- Changes to the EFI init code to establish whether secure boot
authentication was performed at boot time. (Josh Boyer, David
Howells)
- Wire up the UEFI memory attributes table for x86. This eliminates
any runtime memory regions that are both writable and executable,
on recent firmware versions. (Sai Praneeth)
- Move the BGRT init code to an earlier stage so that we can still
use efi_mem_reserve(). (Dave Young)
- Preserve debug symbols in the ARM/arm64 UEFI stub (Ard Biesheuvel)
- Code deduplication work and various other cleanups (Lukas Wunner)
- ... plus various other fixes and cleanups"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub: Make file I/O chunking x86-specific
efi: Print the secure boot status in x86 setup_arch()
efi: Disable secure boot if shim is in insecure mode
efi: Get and store the secure boot status
efi: Add SHIM and image security database GUID definitions
arm/efi: Allow invocation of arbitrary runtime services
x86/efi: Allow invocation of arbitrary runtime services
efi/libstub: Preserve .debug sections after absolute relocation check
efi/x86: Add debug code to print cooked memmap
efi/x86: Move the EFI BGRT init code to early init code
efi: Use typed function pointers for the runtime services table
efi/esrt: Fix typo in pr_err() message
x86/efi: Add support for EFI_MEMORY_ATTRIBUTES_TABLE
efi: Introduce the EFI_MEM_ATTR bit and set it from the memory attributes table
efi: Make EFI_MEMORY_ATTRIBUTES_TABLE initialization common across all architectures
x86/efi: Deduplicate efi_char16_printk()
efi: Deduplicate efi_file_size() / _read() / _close()
Pull timer updates from Thomas Gleixner:
"Nothing exciting, just the usual pile of fixes, updates and cleanups:
- A bunch of clocksource driver updates
- Removal of CONFIG_TIMER_STATS and the related /proc file
- More posix timer slim down work
- A scalability enhancement in the tick broadcast code
- Math cleanups"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
hrtimer: Catch invalid clockids again
math64, tile: Fix build failure
clocksource/drivers/arm_arch_timer:: Mark cyclecounter __ro_after_init
timerfd: Protect the might cancel mechanism proper
timer_list: Remove useless cast when printing
time: Remove CONFIG_TIMER_STATS
clocksource/drivers/arm_arch_timer: Work around Hisilicon erratum 161010101
clocksource/drivers/arm_arch_timer: Introduce generic errata handling infrastructure
clocksource/drivers/arm_arch_timer: Remove fsl-a008585 parameter
clocksource/drivers/arm_arch_timer: Add dt binding for hisilicon-161010101 erratum
clocksource/drivers/ostm: Add renesas-ostm timer driver
clocksource/drivers/ostm: Document renesas-ostm timer DT bindings
clocksource/drivers/tcb_clksrc: Use 32 bit tcb as sched_clock
clocksource/drivers/gemini: Add driver for the Cortina Gemini
clocksource: add DT bindings for Cortina Gemini
clockevents: Add a clkevt-of mechanism like clksrc-of
tick/broadcast: Reduce lock cacheline contention
timers: Omit POSIX timer stuff from task_struct when disabled
x86/timer: Make delay() work during early bootup
delay: Add explanation of udelay() inaccuracy
...
Long standing issue with JITed programs is that stack traces from
function tracing check whether a given address is kernel code
through {__,}kernel_text_address(), which checks for code in core
kernel, modules and dynamically allocated ftrace trampolines. But
what is still missing is BPF JITed programs (interpreted programs
are not an issue as __bpf_prog_run() will be attributed to them),
thus when a stack trace is triggered, the code walking the stack
won't see any of the JITed ones. The same for address correlation
done from user space via reading /proc/kallsyms. This is read by
tools like perf, but the latter is also useful for permanent live
tracing with eBPF itself in combination with stack maps when other
eBPF types are part of the callchain. See offwaketime example on
dumping stack from a map.
This work tries to tackle that issue by making the addresses and
symbols known to the kernel. The lookup from *kernel_text_address()
is implemented through a latched RB tree that can be read under
RCU in fast-path that is also shared for symbol/size/offset lookup
for a specific given address in kallsyms. The slow-path iteration
through all symbols in the seq file done via RCU list, which holds
a tiny fraction of all exported ksyms, usually below 0.1 percent.
Function symbols are exported as bpf_prog_<tag>, in order to aide
debugging and attribution. This facility is currently enabled for
root-only when bpf_jit_kallsyms is set to 1, and disabled if hardening
is active in any mode. The rationale behind this is that still a lot
of systems ship with world read permissions on kallsyms thus addresses
should not get suddenly exposed for them. If that situation gets
much better in future, we always have the option to change the
default on this. Likewise, unprivileged programs are not allowed
to add entries there either, but that is less of a concern as most
such programs types relevant in this context are for root-only anyway.
If enabled, call graphs and stack traces will then show a correct
attribution; one example is illustrated below, where the trace is
now visible in tooling such as perf script --kallsyms=/proc/kallsyms
and friends.
Before:
7fff8166889d bpf_clone_redirect+0x80007f0020ed (/lib/modules/4.9.0-rc8+/build/vmlinux)
f5d80 __sendmsg_nocancel+0xffff006451f1a007 (/usr/lib64/libc-2.18.so)
After:
7fff816688b7 bpf_clone_redirect+0x80007f002107 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fffa0575728 bpf_prog_33c45a467c9e061a+0x8000600020fb (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fffa07ef1fc cls_bpf_classify+0x8000600020dc (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff81678b68 tc_classify+0x80007f002078 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164d40b __netif_receive_skb_core+0x80007f0025fb (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164d718 __netif_receive_skb+0x80007f002018 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164e565 process_backlog+0x80007f002095 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164dc71 net_rx_action+0x80007f002231 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff81767461 __softirqentry_text_start+0x80007f0020d1 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff817658ac do_softirq_own_stack+0x80007f00201c (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff810a2c20 do_softirq+0x80007f002050 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff810a2cb5 __local_bh_enable_ip+0x80007f002085 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8168d452 ip_finish_output2+0x80007f002152 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8168ea3d ip_finish_output+0x80007f00217d (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8168f2af ip_output+0x80007f00203f (/lib/modules/4.9.0-rc8+/build/vmlinux)
[...]
7fff81005854 do_syscall_64+0x80007f002054 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff817649eb return_from_SYSCALL_64+0x80007f002000 (/lib/modules/4.9.0-rc8+/build/vmlinux)
f5d80 __sendmsg_nocancel+0xffff01c484812007 (/usr/lib64/libc-2.18.so)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the dummy bpf_jit_compile() stubs for eBPF JITs and make
that a single __weak function in the core that can be overridden
similarly to the eBPF one. Also remove stale pr_err() mentions
of bpf_jit_compile.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add necessary initial configuration for clocks of display subsystem.
Till now it worked mostly thanks to bootloader.
2. Use macro definitions instead of hard-coded values for pinctrl on Exynos7.
3. Enable USB 3.0 (DWC3) on Exynos7.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJYk3YaAAoJEME3ZuaGi4PXYwAP/2d7SiLymurXwmctrxm9Q5kI
ZD7xdTr5JWq/sbuGfDHLKUz4iPMBsdQqRwczZ+DSls+Iet1fNw4enmoU/p1SpZ/5
31EFB3uN28DSL4ZA3SzOrzPgcdMRxXOYhUMq9DTY5N8h0LlI2TwB3WBDgWTpGB6R
NXX3wKulH2hXJyOizOZh2yel5KvzLqug7j/V0u9K1OmUISmTy3XfDWaXIVk33MUw
IZ6qpgTzShw6sZj5VmR9CFPFbDjwExTVenIA9gwewJlQNQnqrsg0BdEF3ZvasW+V
eFeLV4ieZHKzEoVjwdxGgTLLwjjL/orsWQ5CYiQNeCKC85rgTVfijTe8s+QKOYAq
SiV1GghHACExpCULhtQiqioFsUAUPJ+iq/EZ9NfNh7QzE5Y05RJ7bRgRd2UdBlN8
BXhekgN5RepLwKWHK8oYivMMpIKzDve1ICRpQYBVxmmwg9nzRz6Nij2YUi4oEb5j
77FOuyKe5M+QCIoKVn2v/CDQMemGkI8OEsKubjDKcOZ2V2COw7Sr1L/GCGVCslLM
FyOjaTKeoIzkrx62qgqGFuNwEaZwW0dDacHrZrccEAn9P9G7O/cU8EE9F5nJqGG0
IeDaPH7BqQ0gOHbvrEkljSbJuuOMQmZJl6qh8MMJYB9P8u9Ft3OXUXJ1qBNZB4si
E5nFWGj0CMm0UfBWgkD/
=02Sx
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/late
Pull "Samsung DeviceTree ARM64 update for v4.11, third round" from Krzysztof Kozłowski:
1. Add necessary initial configuration for clocks of display subsystem.
Till now it worked mostly thanks to bootloader.
2. Use macro definitions instead of hard-coded values for pinctrl on Exynos7.
3. Enable USB 3.0 (DWC3) on Exynos7.
* tag 'samsung-dt64-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (27 commits)
arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
clk: samsung: exynos5433: Add data for 250MHz and 278MHz PLL rates
clk: samsung: exynos5433: Add IDs for PHYCLK_MIPIDPHY0_* clocks
arm64: dts: exynos: Add clocks to Exynos5433 LPASS module
arm64: dts: exynos: set LDO7 regulator as always on
arm64: dts: exynos: configure TV path clocks for Ultra HD modes
arm64: dts: exynos: Fix drive strength of sd0_xxx pin definitions
arm64: dts: exynos: Disable pull down for audio pins in Exynos5433 SoCs
arm64: dts: exynos: Add TM2 touchkey node
arm64: dts: exynos: Remove unneeded unit names in Exynos5433 nodes
arm64: dts: exynos: Enable HDMI/TV path on Exynos5433-TM2
arm64: dts: exynos: Add HDMI node to Exynos5433
arm64: dts: exynos: Add DECON_TV node to Exynos5433
arm64: dts: exynos: Fix addresses in node names on Exynos5433
arm64: dts: exynos: Make TM2 and TM2E independent from each other
arm64: dts: exynos: Fix wrong values for ldo23 and ldo25 on TM2/TM2E
...
Now that we have XZR-safe helpers for fiddling with registers, use these
in the arm64 kprobes code rather than open-coding the logic.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In emulate_mrs() we may erroneously write back to the user SP rather
than XZR if we trap an MRS instruction where Xt == 31.
Use the new pt_regs_write_reg() helper to handle this correctly.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Fixes: 77c97b4ee2 ("arm64: cpufeature: Expose CPUID registers by emulation")
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently we hand-roll XZR-safe register handling in
user_cache_maint_handler(), though we forget to do the same in
ctr_read_handler(), and may erroneously write back to the user SP rather
than XZR.
Use the new helpers to handle these cases correctly and consistently.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Fixes: 116c81f427 ("arm64: Work around systems with mismatched cache line sizes")
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In A64, XZR and the SP share the same encoding (31), and whether an
instruction accesses XZR or SP for a particular register parameter
depends on the definition of the instruction.
We store the SP in pt_regs::regs[31], and thus when emulating
instructions, we must be careful to not erroneously read from or write
back to the saved SP. Unfortunately, we often fail to be this careful.
In all cases, instructions using a transfer register parameter Xt use
this to refer to XZR rather than SP. This patch adds helpers so that we
can more easily and consistently handle these cases.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In a randconfig build I ran into this build error:
arch/arm64/kernel/entry-ftrace.S: Assembler messages:
arch/arm64/kernel/entry-ftrace.S:101: Error: unknown mnemonic `ldr_l' -- `ldr_l x2,ftrace_trace_function'
The macro is defined in asm/assembler.h, so we should include that file.
Fixes: 829d2bd133 ("arm64: entry-ftrace.S: avoid open-coded {adr,ldr}_l")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
With 4 levels of 16KB pages, we get this warning about the fact that we are
copying a whole page into an array that is declared as having only two pointers
for the top level of the page table:
arch/arm64/mm/mmu.c: In function 'paging_init':
arch/arm64/mm/mmu.c:528:2: error: 'memcpy' writing 16384 bytes into a region of size 16 overflows the destination [-Werror=stringop-overflow=]
This is harmless since we actually reserve a whole page in the definition of the
array that comes from, and just the extern declaration is short. The pgdir
is initialized to zero either way, so copying the actual entries here seems
like the best solution.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Recently a new dm_op[1] hypercall was added to Xen to provide a mechanism
for restricting device emulators (such as QEMU) to a limited set of
hypervisor operations, and being able to audit those operations in the
kernel of the domain in which they run.
This patch adds IOCTL_PRIVCMD_DM_OP as gateway for __HYPERVISOR_dm_op.
NOTE: There is no requirement for user-space code to bounce data through
locked memory buffers (as with IOCTL_PRIVCMD_HYPERCALL) since
privcmd has enough information to lock the original buffers
directly.
[1] http://xenbits.xen.org/gitweb/?p=xen.git;a=commit;h=524a98c2
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
On ARMv8 implementations that do not support the Crypto Extensions,
such as the Raspberry Pi 3, the CCM driver falls back to the generic
table based AES implementation to perform the MAC part of the
algorithm, which is slow and not time invariant. So add a CBCMAC
implementation to the shared glue code between NEON AES and Crypto
Extensions AES, so that it can be used instead now that the CCM
driver has been updated to look for CBCMAC implementations other
than the one it supplies itself.
Also, given how these algorithms mostly only differ in the way the key
handling and the final encryption are implemented, expose CMAC and XCBC
algorithms as well based on the same core update code.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The PMULL based CRC32 implementation already contains code based on the
separate, optional CRC32 instructions to fallback to when operating on
small quantities of data. We can expose these routines directly on systems
that lack the 64x64 PMULL instructions but do implement the CRC32 ones,
which makes the driver that is based solely on those CRC32 instructions
redundant. So remove it.
Note that this aligns arm64 with ARM, whose accelerated CRC32 driver
also combines the CRC32 extension based and the PMULL based versions.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Qualcomm Datacenter Technologies Falkor v1 CPU may allocate TLB entries
using an incorrect ASID when TTBRx_EL1 is being updated. When the erratum
is triggered, page table entries using the new translation table base
address (BADDR) will be allocated into the TLB using the old ASID. All
circumstances leading to the incorrect ASID being cached in the TLB arise
when software writes TTBRx_EL1[ASID] and TTBRx_EL1[BADDR], a memory
operation is in the process of performing a translation using the specific
TTBRx_EL1 being written, and the memory operation uses a translation table
descriptor designated as non-global. EL2 and EL3 code changing the EL1&0
ASID is not subject to this erratum because hardware is prohibited from
performing translations from an out-of-context translation regime.
Consider the following pseudo code.
write new BADDR and ASID values to TTBRx_EL1
Replacing the above sequence with the one below will ensure that no TLB
entries with an incorrect ASID are used by software.
write reserved value to TTBRx_EL1[ASID]
ISB
write new value to TTBRx_EL1[BADDR]
ISB
write new value to TTBRx_EL1[ASID]
ISB
When the above sequence is used, page table entries using the new BADDR
value may still be incorrectly allocated into the TLB using the reserved
ASID. Yet this will not reduce functionality, since TLB entries incorrectly
tagged with the reserved ASID will never be hit by a later instruction.
Based on work by Shanker Donthineni <shankerd@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The SPE architecture requires each exception level to enable access
to the SPE controls for the exception level below it, since additional
context-switch logic may be required to handle the buffer safely.
This patch allows EL1 (host) access to the SPE controls when entered at
EL2.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This will allow the default kernel build to boot on Cavium ThunderX2
CN99XX processors.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for ThunderX2 CN99XX arm64 server processors.
Introduce a new arm64 platform config option ARCH_THUNDER2 for these
processors.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
adjust name of sd-mmc-gop clock in sysco for Armada 7K/8K
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWJCWUCMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71YLYAJsGQxfg30DY
invLPTtpT7c8xBx/7gCeKmbV8qgukU7rq9L1/T3OeLrPqTI=
=2tUY
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.11-3' of git://git.infradead.org/linux-mvebu into next/dt64
Pull "mvebu dt for 4.11 (part 3)" from Gregory CLEMENT:
adjust name of sd-mmc-gop clock in sysco for Armada 7K/8K
* tag 'mvebu-dt64-4.11-3' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon
Some patches related the arm64 Allwinner SoCs, most notably:
- Support for the MMC
- Suport for the USB and mUSB controllers
- New boards: Bananapi M64
-----BEGIN PGP SIGNATURE-----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=//in
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt64
Pull "Allwinner arm64 changes for 4.11" from Maxime Ripard:
Some patches related the arm64 Allwinner SoCs, most notably:
- Support for the MMC
- Suport for the USB and mUSB controllers
- New boards: Bananapi M64
* tag 'sunxi-dt64-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
arm64: allwinner: add BananaPi-M64 support
arm64: allwinner: a64: add UART1 pin nodes
arm64: allwinner: pine64: add MMC support
arm64: allwinner: a64: Increase the MMC max frequency
arm64: allwinner: a64: Add MMC pinctrl nodes
arm64: allwinner: a64: Add MMC nodes
arm64: dts: allwinner: Remove no longer used pinctrl/sun4i-a10.h header
arm64: dts: enable the MUSB controller of Pine64 in host-only mode
arm64: dts: add MUSB node to Allwinner A64 dtsi
arm64: dts: allwinner: enable EHCI1, OHCI1 and USB PHY nodes in Pine64
arm64: dts: allwinner: sort the nodes in sun50i-a64-pine64.dts
arm64: dts: allwinner: add USB1-related nodes of Allwinner A64
To is_vmalloc_addr() to check if an address is a vmalloc address
instead of checking VMALLOC_START and VMALLOC_END manually.
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently in arm64's copy_{to,from}_user, we only check the
source/destination object size if access_ok() tells us the user access
is permissible.
However, in copy_from_user() we'll subsequently zero any remainder on
the destination object. If we failed the access_ok() check, that applies
to the whole object size, which we didn't check.
To ensure that we catch that case, this patch hoists check_object_size()
to the start of copy_from_user(), matching __copy_from_user() and
__copy_to_user(). To make all of our uaccess copy primitives consistent,
the same is done to copy_to_user().
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- A relatively large patch restores booting on i.MX platforms that
failed to boot after a cleanup was merged for v4.10.
- A quirk for USB needs to be enabled on the STi platform
- On the Meson platform, we saw memory corruption with part of
the memory used by the secure monitor, so we have to stay out
of that area.
- The same platform also has a problem with ethernet under load,
which is fixed by disabling EEE negotiation.
- imx6dl has an incorrect pin configuration, which prevents SPI
from working.
- Two maintainers have lost their access to their email addresses, so
we should update the MAINTAINERS file before the release
- Renaming one of the orion5x linkstation models to help simplify
the debian install.
- A couple of fixes for build warnings that were introduced during
v4.10-rc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zlTb
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
- A relatively large patch restores booting on i.MX platforms that
failed to boot after a cleanup was merged for v4.10.
- A quirk for USB needs to be enabled on the STi platform
- On the Meson platform, we saw memory corruption with part of the
memory used by the secure monitor, so we have to stay out of that
area.
- The same platform also has a problem with ethernet under load, which
is fixed by disabling EEE negotiation.
- imx6dl has an incorrect pin configuration, which prevents SPI from
working.
- Two maintainers have lost their access to their email addresses, so
we should update the MAINTAINERS file before the release
- Renaming one of the orion5x linkstation models to help simplify the
debian install.
- A couple of fixes for build warnings that were introduced during
v4.10-rc.
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: defconfigs: make NF_CT_PROTO_SCTP and NF_CT_PROTO_UDPLITE built-in
MAINTAINERS: socfpga: update email for Dinh Nguyen
ARM: orion5x: fix Makefile for linkstation-lschl.dtb
ARM: dts: orion5x-lschl: More consistent naming on linkstation series
ARM: dts: orion5x-lschl: Fix model name
MAINTAINERS: change email address from atmel to microchip
MAINTAINERS: at91: change email address
ARM64: dts: meson-gx: Add firmware reserved memory zones
ARM64: dts: meson-gxbb-odroidc2: fix GbE tx link breakage
ARM: dts: STiH407-family: set snps,dis_u3_susphy_quirk
ARM: dts: imx: Pass 'chosen' and 'memory' nodes
ARM: dts: imx6dl: fix GPIO4 range
ARM: imx: hide unused variable in #ifdef
Emulate read and write operations to CNTP_TVAL, CNTP_CVAL and CNTP_CTL.
Now VMs are able to use the EL1 physical timer.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
KVM traps on the EL1 phys timer accesses from VMs, but it doesn't handle
those traps. This results in terminating VMs. Instead, set a handler for
the EL1 phys timer access, and inject an undefined exception as an
intermediate step.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Initialize the emulated EL1 physical timer with the default irq number.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Make cntvoff per each timer context. This is helpful to abstract kvm
timer functions to work with timer context without considering timer
types (e.g. physical timer or virtual timer).
This also would pave the way for ever doing adjustments of the cntvoff
on a per-CPU basis if that should ever make sense.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The sysfs cpu_capacity entry for each CPU has nothing to do with
PROC_FS, nor it's in /proc/sys path.
Remove such ifdef.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reported-and-suggested-by: Sudeep Holla <sudeep.holla@arm.com>
Fixes: be8f185d8a ('arm64: add sysfs cpu_capacity attribute')
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Due to the reference clock comes from 26M oscillator directly
on mt8173, and it is a fixed-clock in DTS which always turned
on, we ignore it before. But on some platforms, it comes
from PLL, and need be controlled, so here add it, no matter
it is a fixed-clock or not.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we have code inline in the arch timer probe path to cater for
Freescale erratum A-008585, complete with ifdeffery. This is a little
ugly, and will get worse as we try to add more errata handling.
This patch refactors the handling of Freescale erratum A-008585. Now the
erratum is described in a generic arch_timer_erratum_workaround
structure, and the probe path can iterate over these to detect errata
and enable workarounds.
This will simplify the addition and maintenance of code handling
Hisilicon erratum 161010101.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
[Mark: split patch, correct Kconfig, reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Both of these options are poorly named. The features they provide are
necessary for system security and should not be considered debug only.
Change the names to CONFIG_STRICT_KERNEL_RWX and
CONFIG_STRICT_MODULE_RWX to better describe what these options do.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Jessica Yu <jeyu@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
There are multiple architectures that support CONFIG_DEBUG_RODATA and
CONFIG_SET_MODULE_RONX. These options also now have the ability to be
turned off at runtime. Move these to an architecture independent
location and make these options def_bool y for almost all of those
arches.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
efi_call_runtime() is provided for x86 to be able abstract mixed mode
support. Provide this for ARM also so that common code work in mixed mode
also.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1486380166-31868-3-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Atomic operation function symbols are exported,when
CONFIG_ARM64_LSE_ATOMICS is defined. Prefix them with notrace, so that
an user can not trace these functions. Tracing these functions causes
kernel crash.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The NUMA code may get confused by the presence of NOMAP regions within
zones, resulting in spurious BUG() checks where the node id deviates
from the containing zone's node id.
Since the kernel has no business reasoning about node ids of pages it
does not own in the first place, enable CONFIG_HOLES_IN_ZONE to ensure
that such pages are disregarded.
Acked-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Back when this was first written, dma_supported() was somewhat of a
murky mess, with subtly different interpretations being relied upon in
various places. The "does device X support DMA to address range Y?"
uses assuming Y to be physical addresses, which motivated the current
iommu_dma_supported() implementation and are alluded to in the comment
therein, have since been cleaned up, leaving only the far less ambiguous
"can device X drive address bits Y" usage internal to DMA API mask
setting. As such, there is no reason to keep a slightly misleading
callback which does nothing but duplicate the current default behaviour;
we already constrain IOVA allocations to the iommu_domain aperture where
necessary, so let's leave DMA mask business to architecture-specific
code where it belongs.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Remove the 'HAVE_KPROBES' dependency from the HAVE_KRETPROBES line,
since HAVE_KPROBES is already selected unconditionally in the Kconfig
line above this one.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David A. Long <dave.long@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandeepa Prabhu <sandeepa.s.prabhu@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/148637486369.19245.316601692744886725.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds a Qualcomm specific quirk to the arm_smccc_smc call.
On Qualcomm ARM64 platforms, the SMC call can return before it has
completed. If this occurs, the call can be restarted, but it requires
using the returned session ID value from the interrupted SMC call.
The quirk stores off the session ID from the interrupted call in the
quirk structure so that it can be used by the caller.
This patch folds in a fix given by Sricharan R:
https://lkml.org/lkml/2016/9/28/272
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds a quirk parameter to the arm_smccc_(smc/hvc) calls.
The quirk structure allows for specialized SMC operations due to SoC
specific requirements. The current arm_smccc_(smc/hvc) is renamed and
macros are used instead to specify the standard arm_smccc_(smc/hvc) or
the arm_smccc_(smc/hvc)_quirk function.
This patch and partial implementation was suggested by Will Deacon.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When building with debugging symbols, take the absolute path to the
vmlinux binary and add it to the special PE/COFF debug table entry.
This allows a debug EFI build to find the vmlinux binary, which is
very helpful in debugging, given that the offset where the Image is
first loaded by EFI is highly unpredictable.
On implementations of UEFI that choose to implement it, this
information is exposed via the EFI debug support table, which is a UEFI
configuration table that is accessible both by the firmware at boot time
and by the OS at runtime, and lists all PE/COFF images loaded by the
system.
The format of the NB10 Codeview entry is based on the definition used
by EDK2, which is our primary reference when it comes to the use of
PE/COFF in the context of UEFI firmware.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: use realpath instead of shell invocation, as discussed on list]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arm64 bit sliced AES core code uses the IV buffer to pass the final
keystream block back to the glue code if the input is not a multiple of
the block size, so that the asm code does not have to deal with anything
except 16 byte blocks. This is done under the assumption that the outgoing
IV is meaningless anyway in this case, given that chaining is no longer
possible under these circumstances.
However, as it turns out, the CCM driver does expect the IV to retain
a value that is equal to the original IV except for the counter value,
and even interprets byte zero as a length indicator, which may result
in memory corruption if the IV is overwritten with something else.
So use a separate buffer to return the final keystream block.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The new bitsliced NEON implementation of AES uses a fallback in two
places: CBC encryption (which is strictly sequential, whereas this
driver can only operate efficiently on 8 blocks at a time), and the
XTS tweak generation, which involves encrypting a single AES block
with a different key schedule.
The plain (i.e., non-bitsliced) NEON code is more suitable as a fallback,
given that it is faster than scalar on low end cores (which is what
the NEON implementations target, since high end cores have dedicated
instructions for AES), and shows similar behavior in terms of D-cache
footprint and sensitivity to cache timing attacks. So switch the fallback
handling to the plain NEON driver.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The non-bitsliced AES implementation using the NEON is highly sensitive
to micro-architectural details, and, as it turns out, the Cortex-A53 on
the Raspberry Pi 3 is a core that can benefit from this code, given that
its scalar AES performance is abysmal (32.9 cycles per byte).
The new bitsliced AES code manages 19.8 cycles per byte on this core,
but can only operate on 8 blocks at a time, which is not supported by
all chaining modes. With a bit of tweaking, we can get the plain NEON
code to run at 22.0 cycles per byte, making it useful for sequential
modes like CBC encryption. (Like bitsliced NEON, the plain NEON
implementation does not use any lookup tables, which makes it easy on
the D-cache, and invulnerable to cache timing attacks)
So tweak the plain NEON AES code to use tbl instructions rather than
shl/sri pairs, and to avoid the need to reload permutation vectors or
other constants from memory in every round. Also, improve the decryption
performance by switching to 16x8 pmul instructions for the performing
the multiplications in GF(2^8).
To allow the ECB and CBC encrypt routines to be reused by the bitsliced
NEON code in a subsequent patch, export them from the module.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Shuffle some instructions around in the __hround macro to shave off
0.1 cycles per byte on Cortex-A57.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Using simple adrp/add pairs to refer to the AES lookup tables exposed by
the generic AES driver (which could be loaded far away from this driver
when KASLR is in effect) was unreliable at module load time before commit
41c066f2c4 ("arm64: assembler: make adr_l work in modules under KASLR"),
which is why the AES code used literals instead.
So now we can get rid of the literals, and switch to the adr_l macro.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the unnecessary alignmask: it is much more efficient to deal with
the misalignment in the core algorithm than relying on the crypto API to
copy the data to a suitably aligned buffer.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the unnecessary alignmask: it is much more efficient to deal with
the misalignment in the core algorithm than relying on the crypto API to
copy the data to a suitably aligned buffer.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the unnecessary alignmask: it is much more efficient to deal with
the misalignment in the core algorithm than relying on the crypto API to
copy the data to a suitably aligned buffer.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We recently discovered that __raw_read_system_reg() erroneously mapped
sysreg IDs to the wrong registers.
To ensure that we don't get hit by a similar issue in future, this patch
makes __raw_read_system_reg() use a macro for each case statement,
ensuring that each case reads the correct register.
To ensure that this patch hasn't introduced an issue, I've binary-diffed
the object files before and after this patch. No code or data sections
differ (though some debug section differ due to line numbering
changing).
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since it was introduced in commit da8d02d19f ("arm64/capabilities:
Make use of system wide safe value"), __raw_read_system_reg() has
erroneously mapped some sysreg IDs to other registers.
For the fields in ID_ISAR5_EL1, our local feature detection will be
erroneous. We may spuriously detect that a feature is uniformly
supported, or may fail to detect when it actually is, meaning some
compat hwcaps may be erroneous (or not enforced upon hotplug).
This patch corrects the erroneous entries.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Fixes: da8d02d19f ("arm64/capabilities: Make use of system wide safe value")
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
The SPE buffer is virtually addressed, using the page tables of the CPU
MMU. Unusually, this means that the EL0/1 page table may be live whilst
we're executing at EL2 on non-VHE configurations. When VHE is in use,
we can use the same property to profile the guest behind its back.
This patch adds the relevant disabling and flushing code to KVM so that
the host can make use of SPE without corrupting guest memory, and any
attempts by a guest to use SPE will result in a trap.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Instead of open-coding the loop, let's use canned macro.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Adding fixed voltage regulators for Vbus and Vbus-boost required
by USB 3.0 DRD controller on Exynos7-espresso board.
Signed-off-by: Vivek Gautam <gautamvivek1987@gmail.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add USB 3.0 DRD controller device node, with its clock
and phy information to enable the same on Exynos7.
Signed-off-by: Vivek Gautam <gautamvivek1987@gmail.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Pull crypto fixes from Herbert Xu:
"This fixes a bug in CBC/CTR on ARM64 that breaks chaining as well as a
bug in the core API that causes registration failures when a driver
unloads and then reloads an algorithm"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arm64/aes-blk - honour iv_out requirement in CBC and CTR modes
crypto: api - Clear CRYPTO_ALG_DEAD bit before registering an alg
During a TLB invalidate sequence targeting the inner shareable domain,
Falkor may prematurely complete the DSB before all loads and stores using
the old translation are observed. Instruction fetches are not subject to
the conditions of this erratum. If the original code sequence includes
multiple TLB invalidate instructions followed by a single DSB, onle one of
the TLB instructions needs to be repeated to work around this erratum.
While the erratum only applies to cases in which the TLBI specifies the
inner-shareable domain (*IS form of TLBI) and the DSB is ISH form or
stronger (OSH, SYS), this changes applies the workaround overabundantly--
to local TLBI, DSB NSH sequences as well--for simplicity.
Based on work by Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
cputime_t is now only used by two architectures:
* powerpc (when CONFIG_VIRT_CPU_ACCOUNTING_NATIVE=y)
* s390
And since the core doesn't use it anymore, we don't need any arch support
from the others. So we can remove their stub implementations.
A final cleanup would be to provide an efficient pure arch
implementation of cputime_to_nsec() for s390 and powerpc and finally
remove include/linux/cputime.h .
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1485832191-26889-36-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add initial set of CoreSight components found on Qualcomm msm8916 and
apq8016 based platforms, including the DragonBoard 410c board.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add initial clock configuration for display subsystem for Exynos5433
based TM2/TM2e boards in device tree in order to avoid dependency on the
configuration left by the bootloader. This initial configuration is also
needed to ensure that display subsystem is operational if display power
domain gets turned off before clock controller is probed and the inital
clock configuration left by the bootloader saved.
TM2 and TM2e uses different rate for DISP PLL clock, but for better
maintainability all 'assigned-clocks-*' properties for DISP CMU are
defines in each board dts instead of redefining the rates property.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Commit cab15ce604 ("arm64: Introduce execute-only page access
permissions") allowed a valid user PTE to have the PTE_USER bit clear.
As a consequence, the pte_valid_not_user() macro in set_pte() was
replaced with pte_valid_global() under the assumption that only user
pages have the nG bit set. EFI mappings, however, also have the nG bit
set and set_pte() wrongly ignores issuing the DSB+ISB.
This patch reinstates the pte_valid_not_user() macro and adds the
PTE_UXN bit check since all kernel mappings have this bit set. For
clarity, pte_exec() is renamed to pte_user_exec() as it only checks for
the absence of PTE_UXN. Consequently, the user executable check in
set_pte_at() drops the pte_ng() test since pte_user_exec() is
sufficient.
Fixes: cab15ce604 ("arm64: Introduce execute-only page access permissions")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This commit adjusts the names of gatable clock #18 of the Marvell Armada
CP110 system controller. This clock not only controls SD/MMC, but also
the GOP (Group Of Ports) used for networking. So the clock is renamed to
{cpm,cps}-sd-mmc-gop instead of {cpm,cps}-sd-mmc.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
1. Use proper drive strengths on Exynos7.
2. Fix significant current leak on Exynos5433-based TM2/TM2E due
to disabled regulator.
3. Add touchkey to TM2, set display clocks for Ultra HD modes.
4. Cleanups and minor fixes for Exynos5433, TM2 and TM2E.
-----BEGIN PGP SIGNATURE-----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=rfRv
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Samsung DeviceTree ARM64 update for v4.11, second round:
1. Use proper drive strengths on Exynos7.
2. Fix significant current leak on Exynos5433-based TM2/TM2E due
to disabled regulator.
3. Add touchkey to TM2, set display clocks for Ultra HD modes.
4. Cleanups and minor fixes for Exynos5433, TM2 and TM2E.
* tag 'samsung-dt64-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Add clocks to Exynos5433 LPASS module
arm64: dts: exynos: set LDO7 regulator as always on
arm64: dts: exynos: configure TV path clocks for Ultra HD modes
arm64: dts: exynos: Fix drive strength of sd0_xxx pin definitions
arm64: dts: exynos: Disable pull down for audio pins in Exynos5433 SoCs
arm64: dts: exynos: Add TM2 touchkey node
arm64: dts: exynos: Remove unneeded unit names in Exynos5433 nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the 5 buttons connected to a resistor laddered matrix and sampled
by the SAR ADC channel 0.
Only the p200 board has these buttons, the P201 doesn't.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the SAR ADC to meson-gxbb.dtsi and meson-gxl.dtsi. GXBB provides a
10-bit ADC while GXL and GXM provide a 12-bit ADC.
Some boards use resistor ladder buttons connected through one of the ADC
channels. On newer devices (GXL and GXM) some boards use pull-ups/downs
to change the resistance (and thus the ADC value) on one of the ADC
channels to indicate the board revision.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Now that we unconditionally flush newly mapped pages to the PoC,
there is no need to care about the "uncached" status of individual
pages - they must all be visible all the way down.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When we fault in a page, we flush it to the PoC (Point of Coherency)
if the faulting vcpu has its own caches off, so that it can observe
the page we just brought it.
But if the vcpu has its caches on, we skip that step. Bad things
happen when *another* vcpu tries to access that page with its own
caches disabled. At that point, there is no garantee that the
data has made it to the PoC, and we access stale data.
The obvious fix is to always flush to PoC when a page is faulted
in, no matter what the state of the vcpu is.
Cc: stable@vger.kernel.org
Fixes: 2d58b733c8 ("arm64: KVM: force cache clean on page fault when caches are off")
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Userspace requires to store and restore of line_level for
level triggered interrupts using ioctl KVM_DEV_ARM_VGIC_GRP_LEVEL_INFO.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
VGICv3 CPU interface registers are accessed using
KVM_DEV_ARM_VGIC_CPU_SYSREGS ioctl. These registers are accessed
as 64-bit. The cpu MPIDR value is passed along with register id.
It is used to identify the cpu for registers access.
The VM that supports SEIs expect it on destination machine to handle
guest aborts and hence checked for ICC_CTLR_EL1.SEIS compatibility.
Similarly, VM that supports Affinity Level 3 that is required for AArch64
mode, is required to be supported on destination machine. Hence checked
for ICC_CTLR_EL1.A3V compatibility.
The arch/arm64/kvm/vgic-sys-reg-v3.c handles read and write of VGIC
CPU registers for AArch64.
For AArch32 mode, arch/arm/kvm/vgic-v3-coproc.c file is created but
APIs are not implemented.
Updated arch/arm/include/uapi/asm/kvm.h with new definitions
required to compile for AArch32.
The version of VGIC v3 specification is defined here
Documentation/virtual/kvm/devices/arm-vgic-v3.txt
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to implement vGICv3 CPU interface access, we will need to perform
table lookup of system registers. We would need both index_to_params() and
find_reg() exported for that purpose, but instead we export a single
function which combines them both.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
VGICv3 Distributor and Redistributor registers are accessed using
KVM_DEV_ARM_VGIC_GRP_DIST_REGS and KVM_DEV_ARM_VGIC_GRP_REDIST_REGS
with KVM_SET_DEVICE_ATTR and KVM_GET_DEVICE_ATTR ioctls.
These registers are accessed as 32-bit and cpu mpidr
value passed along with register offset is used to identify the
cpu for redistributor registers access.
The version of VGIC v3 specification is defined here
Documentation/virtual/kvm/devices/arm-vgic-v3.txt
Also update arch/arm/include/uapi/asm/kvm.h to compile for
AArch32 mode.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Banana Pi M64 board is a typical single board computer based on the
Allwinner A64 SoC. Aside from the usual peripherals it features eMMC
storage, which is connected to the 8-bit capable SDHC2 controller.
Also it has a soldered WiFi/Bluetooth chip, so we enable UART1 and SDHC1
as those two interfaces are connected to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
On many boards UART1 connects to a Bluetooth chip, so add the pinctrl
nodes for the only pins providing access to that UART. That includes
those pins for hardware flow control (RTS/CTS).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All Pine64 boards connect an micro-SD card slot to the first MMC
controller.
Enable the respective DT node and specify the (always-on) regulator
and card-detect pin.
As a micro-SD slot does not feature a write-protect switch, we disable
this feature.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The eMMC controller seem to have a maximum frequency of 200MHz, while the
regular MMC controllers are capped at 150MHz.
Since older SoCs cannot go that high, we cannot change the default maximum
frequency, but fortunately for us we have a property for that in the DT.
This also has the side effect of allowing to use the MMC HS200 and SD
SDR104 modes for the boards that support it (with either 1.2v or 1.8v IOs).
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
