of_get_phy_mode() uses a local array to map phy_interface_t values from
include/linux/net/phy.h to a string which is read from the 'phy-mode' or
'phy-connection-type' property. In preparation for exposing the PHY
interface mode through sysfs, perform the following:
- mode phy_modes from drivers/of/of_net.c to include/linux/phy.h such
that it is right below the phy_interface_t enum
- make it a static inline function returning the string such that we can
use it by just including include/linux/net/phy.h
- add a PHY_INTERFACE_MODE_MAX enum value to guard the iteration in
of_get_phy_mode()
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
- Add new documents with guidelines for DT binding stability and review
process. This is one of the outcomes of Kernel Summit DT discussions.
- Remove a bunch of device_type usage which is only for OF and
deprecated with FDT.
- Fix a long standing issue with compatible string match ordering.
- Various minor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJS4T/IAAoJEMhvYp4jgsXiGY4H/jw3ldOrsRK+E2WuTi2iFsaj
UrDBEkLeL920abdk1Ba19AtMLBoroUr1HuyrCqiKfhilzqWi662YWCLWHZ6KPzGG
6d5+YztZ2MnoPzcD7RHd9aojL79V8/OGJpitm9NEDdq5GlQ2/v8/Q7ap2tSGFAV6
+qp5AKLUE0vNm8Lx+0t7NE1Qov2QFvbNycSk4CPOG7nvNBBOfbj7yuofFJmcQxZZ
gjOYEve9lf+jjigwq5YyQdYdAPs2kAKE8/DtJf6WaRXjyWpLpvgYqgPJ9mWcJzFK
FKOHvgfxyK0VmWuIfVKg5GASomWPzABXaBGJWG1phtLa3H+Qv+ZKgtYduKrlxkw=
=vXAO
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Add new documents with guidelines for DT binding stability and review
process. This is one of the outcomes of Kernel Summit DT discussions
- Remove a bunch of device_type usage which is only for OF and
deprecated with FDT
- Fix a long standing issue with compatible string match ordering
- Various minor binding documentation updates
* tag 'devicetree-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: add rockchip vendor prefix
serial: vt8500: Add missing binding document for arch-vt8500 serial driver.
dt/bindings: submitting patches and ABI documents
DT: Add vendor prefix for Emerging Display Technologies
of: add vendor prefixe for EPFL
of: add vendor prefix for Gumstix
of: add vendor prefix for Ka-Ro electronics GmbH
devicetree: macb: Document clock properties
dts: bindings: trivial clock bindings doc fixes
of: Fix __of_device_is_available check
dt/bindings: Remove device_type "serial" from marvell,mv64360-mpsc
dt/bindings: remove device_type "network" references
dt/bindings: remove users of device_type "mdio"
dt/bindings: Remove references to linux,phandle properties
dt/bindings: Remove all references to device_type "ethernet-phy"
of: irq: Ignore disabled intc's when searching map
of: irq: Ignore disabled interrupt controllers
OF: base: match each node compatible against all given matches first
dt-bindings: add GIC-400 binding
Fix a problem that, the platform bus supports the OF style modalias
in .uevent() call, but not in its device 'modalias' sysfs attribute.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
From IEEE 1275, there defined a standard 'status' property indicating the
operational status of one device. The 'status' property has four possible
values: 'okay/ok', 'disabled', 'fail' and 'fail-xxx'.
If it is absent, that means the status of the device is unknown or okay.
The __of_device_is_available checks the state of the 'status' property of
a device. If the property is absent or set to 'okay/ok', it returns 1.
Otherwise it returns 0.
While in __of_device_is_available:
> status = of_get_property(device, "status", &statlen);
> if (status == NULL)
> return 1;
The status value returned from 'of_get_property()' will be NULL in two cases:
Firstly: the 'device' value (device node) is NULL.
Secondly: the 'status' property is actaully not exist.
If the device node is NULL, the __of_device_is_available will return true,
that will mean the absent state of the 'status' property.
So this add the device node check before checking the 'status' property's
state, and if the device node is not exist, 0 will be returned.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
10G PHYs don't currently support running the state machine, which
is implicitly setup via of_phy_connect(). Therefore, it is necessary
to implement an OF version of phy_attach(), which does everything
except start the state machine.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2361613206, "of/irq: Refactor interrupt-map parsing" changed
the refcount on the device_node causing an error in of_node_put():
ERROR: Bad of_node_put() on /pci@800000020000000
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-rc3-dirty #2
Call Trace:
[c00000003e403500] [c0000000000144fc] .show_stack+0x7c/0x1f0 (unreliable)
[c00000003e4035d0] [c00000000070f250] .dump_stack+0x88/0xb4
[c00000003e403650] [c0000000005e8768] .of_node_release+0xd8/0xf0
[c00000003e4036e0] [c0000000005eeafc] .of_irq_parse_one+0x10c/0x280
[c00000003e4037a0] [c0000000005efd4c] .of_irq_parse_pci+0x3c/0x1d0
[c00000003e403840] [c000000000038240] .pcibios_setup_device+0xa0/0x2e0
[c00000003e403910] [c0000000000398f0] .pcibios_setup_bus_devices+0x60/0xd0
[c00000003e403990] [c00000000003b3a4] .__of_scan_bus+0x1a4/0x2b0
[c00000003e403a80] [c00000000003a62c] .pcibios_scan_phb+0x30c/0x410
[c00000003e403b60] [c0000000009fe430] .pcibios_init+0x7c/0xd4
This patch adjusts the refcount in the walk of the interrupt tree.
When a match is found, there is no need to increase the refcount
on 'out_irq->np' as 'newpar' is already holding a ref. The refcount
balance between 'ipar' and 'newpar' is maintained in the skiplevel:
goto label.
This patch also removes the usage of the device_node variable 'old'
which seems useless after the latest changes.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This reverts commit e38c0a1fbc.
Nikita Yushchenko reports:
While trying to make freescale p2020ds and mpc8572ds boards working
with mainline kernel, I faced that commit e38c0a1f (Handle
Both these boards have uli1575 chip.
Corresponding part in device tree is something like
uli1575@0 {
reg = <0x0 0x0 0x0 0x0 0x0>;
#size-cells = <2>;
#address-cells = <3>;
ranges = <0x2000000 0x0 0x80000000
0x2000000 0x0 0x80000000
0x0 0x20000000
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x10000>;
isa@1e {
...
I.e. it has #address-cells = <3>
With commit e38c0a1f reverted, devices under uli1575 are registered
correctly, e.g. for rtc
OF: ** translation for device /pcie@ffe09000/pcie@0/uli1575@0/isa@1e/rtc@70 **
OF: bus is isa (na=2, ns=1) on /pcie@ffe09000/pcie@0/uli1575@0/isa@1e
OF: translating address: 00000001 00000070
OF: parent bus is default (na=3, ns=2) on /pcie@ffe09000/pcie@0/uli1575@0
OF: walking ranges...
OF: ISA map, cp=0, s=1000, da=70
OF: parent translation for: 01000000 00000000 00000000
OF: with offset: 70
OF: one level translation: 00000000 00000000 00000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000/pcie@0
OF: walking ranges...
OF: default map, cp=a0000000, s=20000000, da=70
OF: default map, cp=0, s=10000, da=70
OF: parent translation for: 01000000 00000000 00000000
OF: with offset: 70
OF: one level translation: 01000000 00000000 00000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000
OF: walking ranges...
OF: PCI map, cp=0, s=10000, da=70
OF: parent translation for: 01000000 00000000 00000000
OF: with offset: 70
OF: one level translation: 01000000 00000000 00000070
OF: parent bus is default (na=2, ns=2) on /
OF: walking ranges...
OF: PCI map, cp=0, s=10000, da=70
OF: parent translation for: 00000000 ffc10000
OF: with offset: 70
OF: one level translation: 00000000 ffc10070
OF: reached root node
With commit e38c0a1f in place, address translation fails:
OF: ** translation for device /pcie@ffe09000/pcie@0/uli1575@0/isa@1e/rtc@70 **
OF: bus is isa (na=2, ns=1) on /pcie@ffe09000/pcie@0/uli1575@0/isa@1e
OF: translating address: 00000001 00000070
OF: parent bus is default (na=3, ns=2) on /pcie@ffe09000/pcie@0/uli1575@0
OF: walking ranges...
OF: ISA map, cp=0, s=1000, da=70
OF: parent translation for: 01000000 00000000 00000000
OF: with offset: 70
OF: one level translation: 00000000 00000000 00000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000/pcie@0
OF: walking ranges...
OF: default map, cp=a0000000, s=20000000, da=70
OF: default map, cp=0, s=10000, da=70
OF: not found !
Thierry Reding confirmed this commit was not needed after all:
"We ended up merging a different address representation for Tegra PCIe
and I've confirmed that reverting this commit doesn't cause any obvious
regressions. I think all other drivers in drivers/pci/host ended up
copying what we did on Tegra, so I wouldn't expect any other breakage
either."
There doesn't appear to be a simple way to support both behaviours, so
reverting this as nothing should be depending on the new behaviour.
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Rob Herring <robh@kernel.org>
Check whether initial_boot_params is NULL before dereferencing it in
unflatten_and_copy_device_tree() for the case where no device tree is
available but the arch can still boot to a minimal usable system without
it. In this case also log a warning for when the kernel log buffer is
obtainable.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The "max-speed" property is defined per the ePAPR specification to
express the maximum speed a PHY supports. Use that property, if present
to set the phydev->supported features which properly restricts the PHY
within the range of defined speeds.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If irq_of_parse_and_map fails to find an interrupt line for a given PHY,
we will force the PHY interrupt to be PHY_POLL, completely overriding
the previous value that the MDIO bus may have set for us (e.g:
PHY_IGNORE_INTERRUPT). In case of failure, just restore the previous
value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the PHY_MAX_ADDR constant for checking if a MDIO bus address is
valid instead of using a plain "32".
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 779d835e ("net: of_mdio: scan mdiobus for PHYs without reg
property") we have two foreach loops which do pretty much the same
thing. Factor the PHY device registration in a function helper:
of_mdiobus_register_phy() which takes care of the details and allows for
future PHY specific extensions.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When searching the interrupt map, if a matched parent is disabled, just
ignore it and move on with the search.
This allows for specifying connection of a single device IRQ to
multiple interrupt controllers via the interrupt map schema. This change
allows for selection of the active interrupt controller via the already
existing status = "disabled" mechanism.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
When searching the system for interrupt controllers, skip over any
that are explicitly disabled.
This makes interrupt controllers consistent with regular devices,
which can be marked as do-not-probe via the status = "disabled" dts
property.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Currently, of_match_node compares each given match against all node's
compatible strings with of_device_is_compatible.
To achieve multiple compatible strings per node with ordering from
specific to generic, this requires given matches to be ordered from
specific to generic. For most of the drivers this is not true and also
an alphabetical ordering is more sane there.
Therefore, this patch modifies of_match_node to match each of the node's
compatible strings against all given matches first, before checking the
next compatible string. This implies that node's compatibles are ordered
from specific to generic while given matches can be in any order.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Pull powerpc updates from Benjamin Herrenschmidt:
"The bulk of this is LE updates. One should now be able to build an LE
kernel and even run some things in it.
I'm still sitting on a handful of patches to enable the new ABI that I
*might* still send this merge window around, but due to the
incertainty (they are pretty fresh) I want to keep them separate.
Other notable changes are some infrastructure bits to better handle
PCI pass-through under KVM, some bits and pieces added to the new
PowerNV platform support such as access to the CPU SCOM bus via sysfs,
and support for EEH error handling on PHB3 (Power8 PCIe).
We also grew arch_get_random_long() for both pseries and powernv when
running on P7+ and P8, exploiting the HW rng.
And finally various embedded updates from freescale"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (154 commits)
powerpc: Fix fatal SLB miss when restoring PPR
powerpc/powernv: Reserve the correct PE number
powerpc/powernv: Add PE to its own PELTV
powerpc/powernv: Add support for indirect XSCOM via debugfs
powerpc/scom: Improve debugfs interface
powerpc/scom: Enable 64-bit addresses
powerpc/boot: Properly handle the base "of" boot wrapper
powerpc/bpf: Support MOD operation
powerpc/bpf: Fix DIVWU instruction opcode
of: Move definition of of_find_next_cache_node into common code.
powerpc: Remove big endianness assumption in of_find_next_cache_node
powerpc/tm: Remove interrupt disable in __switch_to()
powerpc: word-at-a-time optimization for 64-bit Little Endian
powerpc/bpf: BPF JIT compiler for 64-bit Little Endian
powerpc: Only save/restore SDR1 if in hypervisor mode
powerpc/pmu: Fix ADB_PMU_LED_IDE dependencies
powerpc/nvram: Fix endian issue when using the partition length
powerpc/nvram: Fix endian issue when reading the NVRAM size
powerpc/nvram: Scan partitions only once
powerpc/mpc512x: remove unnecessary #if
...
Fix OF selftest compile on sparc which does not enable OF_IRQ.
drivers/of/selftest.c:177: undefined reference to `of_irq_parse_one'
drivers/of/selftest.c:197: undefined reference to `of_irq_parse_one'
drivers/of/selftest.c:248: undefined reference to `of_irq_parse_one'
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
This patch fixes interrupt-map entry matching code to properly match all
specifier cells with interrupt map entries.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Commit 2361613206, "of/irq: Refactor interrupt-map parsing" introduced
a potential buffer overflow bug because it doesn't do sufficient range
checking on the input data. This patch adds the appropriate checking and
buffer size adjustments. If the bounds are out of range then warn
loudly. MAX_PHANDLE_ARGS should be sufficient. If it is not then the
value can be increased.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Commit 2361613206, "of/irq: Refactor interrupt-map parsing" introduced
a bug. The irq parsing will fail for some nodes that don't have a reg
property. It is fixed by deferring the check for reg until it is
actually needed. Also adjust the testcase data to catch the bug.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Platform devices created by DT code don't initialize dma_mask pointer to
anything. Set it to coherent_dma_mask by default if the architecture
code has not set it.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
AMBA Primecell devices always treat streaming and coherent DMA exactly
the same, so there's no point in having the masks separated.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the definition of_find_next_cache_node is architecture independent,
the existing definition in powerpc can be moved to driver/of/base.c
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The standard interrupts property in device tree can only handle
interrupts coming from a single interrupt parent. If a device is wired
to multiple interrupt controllers, then it needs to be attached to a
node with an interrupt-map property to demux the interrupt specifiers
which is confusing. It would be a lot easier if there was a form of the
interrupts property that allows for a separate interrupt phandle for
each interrupt specifier.
This patch does exactly that by creating a new interrupts-extended
property which reuses the phandle+arguments pattern used by GPIOs and
other core bindings.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
[grant.likely: removed versatile platform hunks into separate patch]
Cc: Rob Herring <rob.herring@calxeda.com>
Several architectures open code effectively the same code block for
finding and mapping PCI irqs. This patch consolidates it down to a
single function.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The of_irq_to_resource() helper that is used to implement of_irq_count()
tries to resolve interrupts and in fact creates a mapping for resolved
interrupts. That's pretty heavy lifting for something that claims to
just return the number of interrupts requested by a given device node.
Instead, use the more lightweight of_irq_map_one(), which, despite the
name, doesn't create an actual mapping. Perhaps a better name would be
of_irq_translate_one().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: fixup s/of_irq_map_one/of_irq_parse_one/]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This patch extends the DT selftest code with some test cases for the
interrupt parsing functions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It is sometimes useful for debug to get the contents of an
of_phandle_args structure out into the kernel log.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
All the users of of_irq_parse_raw pass in a raw interrupt specifier from
the device tree and expect it to be returned (possibly modified) in an
of_phandle_args structure. However, the primary function of
of_irq_parse_raw() is to check for translations due to the presence of
one or more interrupt-map properties. The actual placing of the data
into an of_phandle_args structure is trivial. If it is refactored to
accept an of_phandle_args structure directly, then it becomes possible
to consume of_phandle_args from other sources. This is important for an
upcoming patch that allows a device to be connected to more than one
interrupt parent. It also simplifies the code a bit.
The biggest complication with this patch is that the old version works
on the interrupt specifiers in __be32 form, but the of_phandle_args
structure is intended to carry it in the cpu-native version. A bit of
churn was required to make this work. In the end it results in tighter
code, so the churn is worth it.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
All the callers of irq_create_of_mapping() pass the contents of a struct
of_phandle_args structure to the function. Since all the callers already
have an of_phandle_args pointer, why not pass it directly to
irq_create_of_mapping()?
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
struct of_irq and struct of_phandle_args are exactly the same structure.
This patch makes the kernel use of_phandle_args everywhere. This in
itself isn't a big deal, but it makes some follow-on patches simpler.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The OF irq handling code has been overloading the term 'map' to refer to
both parsing the data in the device tree and mapping it to the internal
linux irq system. This is probably because the device tree does have the
concept of an 'interrupt-map' function for translating interrupt
references from one node to another, but 'map' is still confusing when
the primary purpose of some of the functions are to parse the DT data.
This patch renames all the of_irq_map_* functions to of_irq_parse_*
which makes it clear that there is a difference between the parsing
phase and the mapping phase. Kernel code can make use of just the
parsing or just the mapping support as needed by the subsystem.
The patch was generated mechanically with a handful of sed commands.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some drivers might rely on availability of trigger flags in IRQ
resource, for example to configure the hardware for particular interrupt
type. However current code creating IRQ resources from data in device
tree does not configure trigger flags in resulting resources.
This patch tries to solve the problem, based on the fact that
irq_of_parse_and_map() configures the trigger based on DT interrupt
specifier and IRQD_TRIGGER_* flags are consistent with IORESOURCE_IRQ_*,
and we can get correct trigger flags by calling irqd_get_trigger_type()
after mapping the interrupt.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
[grant.likely: Merged the two assignments to r->flags]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Several locations in the of_address and of_irq code dereference the
full_name parameter from a device_node pointer without checking if the
pointer is valid. This patch switches to use of_node_full_name() which
always checks the pointer.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The size of each hwid in a cpu nodes 'reg' property is defined by the
parents #address-cells property in the normal way. The cpu parsing code
has a bug where it will overrun the end of the property if
address-cells is greater than one. This commit fixes the problem by
adjusting the array size by the number of address cells. It also makes
sure address-cells isn't zero for that would cause an infinite loop.
v2: bail if #address-cells is zero instead of forcing to
OF_ROOT_NODE_ADDR_CELLS_DEFAULT. Forcing it will cause the reg
property to be parsed incorrectly.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use for_each_node_by_type() to iterate all cpu nodes in the
system.
Provide and overridable function arch_find_n_match_cpu_physical_id,
which sees if the given device node matches 'cpu' and if so sets
'*thread' when non-NULL to the cpu thread number within the core.
The default implementation behaves the same as the existing code.
Add a sparc64 implementation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Sudeep KarkadaNagesha <Sudeep.KarkadaNagesha@arm.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This reverts commit 9d8eab7af7. There is
still no consensus on the bindings for the reserved memory and various
drawbacks of the proposed solution has been shown, so the best now is to
revert it completely and start again from scratch later.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This reverts commit 109b623629.
Tim Bird expressed concern that this will have a bad effect on boot
time, and while simple tests have shown it to be okay with simple tree,
a device tree blob can potentially be quite large and
add_device_randomness() is not a fast function. Rather than do this for
all platforms unconditionally, I'm reverting this patch and would like
to see it revisited. Instead of feeding the entire tree into the random
pool, it would probably be appropriate to hash the tree and feed the
hash result into the pool. There really isn't a lot of randomness in a
device tree anyway. In the majority of cases only a handful of
properties are going to be different between machines with the same
baseboard.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Not all DT platforms have all the cpus collected under a /cpus node.
That just happens to be a details of FDT, ePAPR and PowerPC platforms.
Sparc does something different, but unfortunately the current code
complains with a warning if /cpus isn't there. This became a problem
with commit f86e4718, "driver/core cpu: initialize of_node in cpu's
device structure", which caused the function to get called for all
architectures.
This commit is a temporary fix to fail silently if the cpus node isn't
present. A proper fix will come later to allow arch code to provide a
custom mechanism for decoding the CPU hwid if the 'reg' property isn't
appropriate.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: David Miller <davem@davemloft.net>
Cc: Sudeep KarkadaNagesha <Sudeep.KarkadaNagesha@arm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Implement of_node_to_nid as weak function to remove the dependency on
asm/prom.h. This is in preparation to make prom.h optional.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
