Status register contains a lot of bits for reporting internal errors
inside Mali DP. Currently, we just silently ignore all of the errors,
that doesn't help when we are investigating different bugs, especially
on the FPGA models which have a lot of constraints, so we could easily
end up in AXI or underrun errors.
Add a new file called debug that contains an aggregate of the
errors reported by the Mali DP hardware.
E.g:
[root@alarm ~]# cat /sys/kernel/debug/dri/1/debug
[DE] num_errors : 167
[DE] last_error_status : 0x00000001
[DE] last_error_vblank : 385
[SE] num_errors : 3
[SE] last_error_status : 0x00e23001
[SE] last_error_vblank : 201
Changes since v2:
- Add lock to protect the errors stats.
- Add possibility to reset the error stats by writing anything to the
debug file.
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali DP500 operates in continuous writeback mode (writes frame content
until stopped) and it needs special handling in order to behave like
a one-shot writeback engine. The original state machine added for DP500
was a bit fragile, as it did not handle correctly cases where a new
atomic commit was in progress when the SE IRQ happens and it would
commit some partial updates.
Improve the handling by adding a parameter to the set_config_valid()
function to clear the config valid bit in hardware before starting a
new commit and by introducing a MW_RESTART state in the writeback
state machine to cater for the case where a new writeback commit
gets submitted while the last one is still being active.
Reported-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali-DP has a memory writeback engine which can be used to write the
composition result to a memory buffer. Expose this functionality as a
DRM writeback connector on supported hardware.
Changes since v1:
Daniel Vetter:
- Don't require a modeset when writeback routing changes
- Make writeback connector always disconnected
Changes since v2:
- Rebase onto new drm_writeback_connector
- Add reset callback, allocating subclassed state
Daniel Vetter:
- Squash out-fence support into this commit
Gustavo Padovan:
- Don't signal fence directly from driver (and drop malidp_mw_job)
Changes since v3:
- Modifications to fit with Mali-DP commit tail changes
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[rebased and fixed conflicts]
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Annotate the pixel format matrix for DP500 with the memory-write flag
for formats that are supported by the SE memwrite engine.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali DP500 behaves differently from the rest of the Mali DP IP,
in that it does not have a one-shot mode and keeps writing the
content of the current frame to the provided memory area until
stopped. As a way of emulating the one-shot behaviour, we are
going to use the CVAL interrupt that is being raised at the
start of each frame, during prefetch phase, to act as End-of-Write
signal, but with a twist: we are going to disable the memory
write engine right after we're notified that it has been enabled,
using the knowledge that the bit controlling the enabling will
only be acted upon on the next vblank/prefetch.
CVAL interrupt will fire durint the next prefetch phase every time
the global CVAL bit gets set, so we need a state byte to track
the memory write enabling. We also need to pay attention during the
disabling of the memory write engine as that requires the CVAL bit
to be set in the control register, but we don't want to do that
during an atomic commit, as it will write into the hardware a partial
state.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Add a layer bit for the SE memory-write, and add it to the pixel format
matrix for DP550/DP650.
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[rebased and fixed conflicts]
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali-DP display processors are able to write the composition result to a
memory buffer via the SE.
Add entry points in the HAL for enabling/disabling this feature, and
implement support for it on DP650 and DP550. DP500 acts differently and
so is omitted from this change.
Changes since v3:
- Fix missing vsync interrupt for DP550
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[rebased and fixed conflicts]
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Two requests have come in for a backmerge,
and I've got some pull reqs on rc2, so this
just makes sense.
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAls2oVcQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpr89D/9PaJCtLpCEU1HdaohIDXDyJKBdtCllIsqJ
YAJTlUkFRkMvsbdEA3U43rVRVlu7zxP3aRg79VRI+kdZ8y8XSiisAF/QUbG/Bwd3
NuFqKj4Hm5xFTtLMKIUlumR2/exD4ZpPHKnWmD4idp1PZRoTUwxeIjqVv77L6Nfy
c4/GVlz2t9buWxH/5PSa//rsT49xM6CLpyIwO2lFsNEk2HYE/uAWya5KZVJ1YKVw
mSjUdyFtJ//lFK9lVU4YkdNF0d5w2PcEoCfNyPe0n9F43iITACo2om7rkSkTgciS
izPAs1DkqNdWPta2twULt656WlUoGlwnWyFchU34N/I/pDiww4kdCQFfNIOi6qBW
7rPQ4xpywiw/U93C2GLEeE09++T8+yO4KuELhIcN5+D3D2VGRIuaGcf4xeY0CX3A
a335EZIxBGOfxyejknBDg3BsoUcLvejbANKD8ltis3zciGf/QyLt+FFqx25WCzkN
N028ppml8WPSiqhSlFDMyfscO1dx/WSYh1q7ANrBiPPaEjFYmakzEDT0cZW4JsUh
av4jqYt3cqrFIXyhRHJM2wjFymQv6aVnmLa4zOKCFbwm9KzMWUUFjc4R962T/sQK
0g+eCSFGidii4JZ4ghOAQk2dqCTIZqV72pmLlpJBGu+SAIQxkh+29h0LOi5U3v1Y
FnTtJ1JhCg==
=0uqV
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180629' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Small set of fixes for this series. Mostly just minor fixes, the only
oddball in here is the sg change.
The sg change came out of the stall fix for NVMe, where we added a
mempool and limited us to a single page allocation. CONFIG_SG_DEBUG
sort-of ruins that, since we'd need to account for that. That's
actually a generic problem, since lots of drivers need to allocate SG
lists. So this just removes support for CONFIG_SG_DEBUG, which I added
back in 2007 and to my knowledge it was never useful.
Anyway, outside of that, this pull contains:
- clone of request with special payload fix (Bart)
- drbd discard handling fix (Bart)
- SATA blk-mq stall fix (me)
- chunk size fix (Keith)
- double free nvme rdma fix (Sagi)"
* tag 'for-linus-20180629' of git://git.kernel.dk/linux-block:
sg: remove ->sg_magic member
drbd: Fix drbd_request_prepare() discard handling
blk-mq: don't queue more if we get a busy return
block: Fix cloning of requests with a special payload
nvme-rdma: fix possible double free of controller async event buffer
block: Fix transfer when chunk sectors exceeds max
This was introduced more than a decade ago when sg chaining was
added, but we never really caught anything with it. The scatterlist
entry size can be critical, since drivers allocate it, so remove
the magic member. Recently it's been triggering allocation stalls
and failures in NVMe.
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
- A single fix in meson for an unhandled error path in meson_drv_bind_master().
-----BEGIN PGP SIGNATURE-----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=zPj3
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-06-28' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v4.18-rc3:
- A single fix in meson for an unhandled error path in meson_drv_bind_master().
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fa740f31-5a8d-ed45-5e8a-aecd3f6f11b7@linux.intel.com
A few fixes for 4.18:
- fix a read past the end of an array due to vega20 changes
- fix driver on systems with non-4K pages
- fix locking with pageflipping in DC that could lead to a sleep while atomic
- fix VCN firmware version reporting for upcoming firmware
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628032641.2765-1-alexander.deucher@amd.com
on all platforms back to HSW. As well many other fix and improvements,
Including:
- Use GEM suspend when aborting initialization (Chris)
- Change i915_gem_fault to return vm_fault_t (Chris)
- Expand VMA to Non gem object entities (Chris)
- Improve logs for load failure, but quite logging on fault injection to avoid noise on CI (Chris)
- Other page directory handling fixes and improvements for gen6 (Chris)
- Other gtt clean-up removing redundancies and unused checks (Chris)
- Reorder aliasing ppgtt fini (Chris)
- Refactor of unsetting obg->mm.pages (Chris)
- Apply batch location restrictions before pinning (Chris)
- Ringbuffer fixes for context restore (Chris)
- Execlist fixes on freeing error pointer on allocation error (Chris)
- Make closing request flush mandatory (Chris)
- Move GEM sanitize from resume_early to resume (Chris)
- Improve debug dumps (Chris)
- Silent compiler for selftest (Chris)
- Other execlists changes to improve hangcheck and reset.
- Many gtt page directory fixes and improvements (Chris)
- Reorg context workarounds (Chris)
- Avoid ERR_PTR dereference on selftest (Chris)
Other GEM related work:
- Stop trying to reset GPU if reset failed (Mika)
- Add HW workaround for KBL to fix GPU reset (Mika)
- Fix context ban and hang accounting for client (Mika)
- Fixes on OA perf (Michel, Jani)
- Refactor on GuC log mechanisms (Piotr)
- Enable provoking vertex fix on Gen9 system (Kenneth)
More ICL patches for Display enabling:
- ICL - 10-bit support for HDMI (RK)
- ICL - Start adding TBT PLL (Paulo)
- ICL - DDI HDMK level selection (Manasi)
- ICL - GMBUS GPIO pin mapping fix (Mahesh)
- ICL - Adding DP_AUX_E support (James)
- ICL - Display interrupts handling (DK)
Other display fixes and improvements:
- Fix sprite destination color keying on SKL+ (Ville)
- Fixes and improvements on PCH detection, specially for non PCH systems (Jani)
- Document PCH_NOP (Lucas)
- Allow DBLSCAN user modes with eDP/LVDS/DSI (Ville)
- Opregion and ACPI cleanup and organization (Jani)
- Kill delays when activation psr (Rodrigo)
- ...and a consequent fix of the psr activation flow (DK)
- Fix HDMI infoframe setting (Imre)
- Fix Display interrupts and modes on old gens (Ville)
- Start switching to kernel unsigned int types (Jani)
- Introduction to Amber Lake and Whiskey Lake platforms (Jose)
- Audio clock fixes for HBR3 (RK)
- Standardize i915_reg.h definitions according to our doc and checkpatch (Paulo)
- Remove unused timespec_to_jiffies_timeout function (Arnd)
- Increase the scope of PSR wake fix for other VBTs out there (Vathsala)
- Improve debug msgs with prop name/id (Ville)
- Other clean up on unecessary cursor size defines (Ville)
- Enforce max hdisplay/hblank_start limits on HSW/BDW (Ville)
- Make ELD pointers constant (Jani)
- Fix for PSR VBT parse (Colin)
- Add warn about unsupported CDCLK rates (Imre)
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbKsMqAAoJEPpiX2QO6xPKI64H/0dHkMxw7/D83eODTJteDFBN
h3tdBnLFlPfeG3ZWDeSs04/dM4e9YacMN7v53j1ia4eW/F1ms0TLcegcuPqYafTW
H8fhwGB2B5gmr5hLfh5joQkxvaucQMFdg95fWRqir93VrKvVJAJEYNcaiGniejDf
qqiZue6DgAzli0zjAprfbQsnJ17TyRtnxm8lLIcFcHPoayHBzAUBZQEP6cA5qe/Y
/2ahGfkYOVVWY08DHaioDBOLUEUbxCC1AvMlv9VbtKmyPoQjTIW/1iTq0RRxDoGb
BwfDvigSiFAmpYEfVENB0qUd9e/0WhMboSnMrfzEcF2yUn4xoJx5nbmkRFkr1jI=
=mfO6
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2018-06-20' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
Chris is doing many reworks that allow us to get full-ppgtt supported
on all platforms back to HSW. As well many other fix and improvements,
Including:
- Use GEM suspend when aborting initialization (Chris)
- Change i915_gem_fault to return vm_fault_t (Chris)
- Expand VMA to Non gem object entities (Chris)
- Improve logs for load failure, but quite logging on fault injection to avoid noise on CI (Chris)
- Other page directory handling fixes and improvements for gen6 (Chris)
- Other gtt clean-up removing redundancies and unused checks (Chris)
- Reorder aliasing ppgtt fini (Chris)
- Refactor of unsetting obg->mm.pages (Chris)
- Apply batch location restrictions before pinning (Chris)
- Ringbuffer fixes for context restore (Chris)
- Execlist fixes on freeing error pointer on allocation error (Chris)
- Make closing request flush mandatory (Chris)
- Move GEM sanitize from resume_early to resume (Chris)
- Improve debug dumps (Chris)
- Silent compiler for selftest (Chris)
- Other execlists changes to improve hangcheck and reset.
- Many gtt page directory fixes and improvements (Chris)
- Reorg context workarounds (Chris)
- Avoid ERR_PTR dereference on selftest (Chris)
Other GEM related work:
- Stop trying to reset GPU if reset failed (Mika)
- Add HW workaround for KBL to fix GPU reset (Mika)
- Fix context ban and hang accounting for client (Mika)
- Fixes on OA perf (Michel, Jani)
- Refactor on GuC log mechanisms (Piotr)
- Enable provoking vertex fix on Gen9 system (Kenneth)
More ICL patches for Display enabling:
- ICL - 10-bit support for HDMI (RK)
- ICL - Start adding TBT PLL (Paulo)
- ICL - DDI HDMK level selection (Manasi)
- ICL - GMBUS GPIO pin mapping fix (Mahesh)
- ICL - Adding DP_AUX_E support (James)
- ICL - Display interrupts handling (DK)
Other display fixes and improvements:
- Fix sprite destination color keying on SKL+ (Ville)
- Fixes and improvements on PCH detection, specially for non PCH systems (Jani)
- Document PCH_NOP (Lucas)
- Allow DBLSCAN user modes with eDP/LVDS/DSI (Ville)
- Opregion and ACPI cleanup and organization (Jani)
- Kill delays when activation psr (Rodrigo)
- ...and a consequent fix of the psr activation flow (DK)
- Fix HDMI infoframe setting (Imre)
- Fix Display interrupts and modes on old gens (Ville)
- Start switching to kernel unsigned int types (Jani)
- Introduction to Amber Lake and Whiskey Lake platforms (Jose)
- Audio clock fixes for HBR3 (RK)
- Standardize i915_reg.h definitions according to our doc and checkpatch (Paulo)
- Remove unused timespec_to_jiffies_timeout function (Arnd)
- Increase the scope of PSR wake fix for other VBTs out there (Vathsala)
- Improve debug msgs with prop name/id (Ville)
- Other clean up on unecessary cursor size defines (Ville)
- Enforce max hdisplay/hblank_start limits on HSW/BDW (Ville)
- Make ELD pointers constant (Jani)
- Fix for PSR VBT parse (Colin)
- Add warn about unsupported CDCLK rates (Imre)
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Thu 21 Jun 2018 07:12:10 AM AEST
# gpg: using RSA key FA625F640EEB13CA
# gpg: Good signature from "Rodrigo Vivi <rodrigo.vivi@intel.com>"
# gpg: aka "Rodrigo Vivi <rodrigo.vivi@gmail.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6D20 7068 EEDD 6509 1C2C E2A3 FA62 5F64 0EEB 13CA
Link: https://patchwork.freedesktop.org/patch/msgid/20180625165622.GA21761@intel.com
drm_of_find_possible_crtcs() doesn't work when DW HDMI encoder is
connected to TCON (crtc) through mux in TCON TOP.
In that case TCON TOP HDMI mux input port has to be manually traversed
and checked if it matches any known crtc.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-23-jernej.skrabec@siol.net
Function is useful when drm_of_find_possible_crtcs() can't be used and
custom parsing is needed. This can happen for example when there is a
node with multiple muxes between crtc and encoder.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[maxime: change the function to have a consistent prefix]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-22-jernej.skrabec@siol.net
DW HDMI PHY driver and PHY clock driver share same registers. Make sure
that DW HDMI PHY setup code doesn't change any clock related bits.
During initialization, set PHY PLL parent bit to 0.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-18-jernej.skrabec@siol.net
Current DW HDMI PHY code never prepares and enables PHY clock after it is
created. It's just used as it is. This may work in some cases, but it's
clearly wrong. Fix it by adding proper calls to enable/disable PHY
clock.
Fixes: 4f86e81748 ("drm/sun4i: Add support for H3 HDMI PHY variant")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-17-jernej.skrabec@siol.net
Both mixers have similar capabilities as others SoCs with DE2.
First mixer has 1 VI and 3 UI planes and supports HW scaling on all
planes.
Second mixer has 1 VI and 1 UI planes and also supports HW scaling on
all planes.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-15-jernej.skrabec@siol.net
TV TCONs are always connected to TV or HDMI encoder, so it doesn't make
sense to check if panel or bridge is connected to them.
Check if TCON has channel 0 and only then check for connected panel or
bridges.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-13-jernej.skrabec@siol.net
LVDS and RGB interfaces are always connected to TCONs which have channel
0. It doesn't make sense to try to init them on TV TCONs.
Add a check if TCON has channel 0 before trying to init LVDS or RGB
interface.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-12-jernej.skrabec@siol.net
Current "old" method to find engine worked pretty well for DE2. However,
it doesn't work when TCON TOP is between mixer (engine) and TCON. TCON
TOP has multiple input ports, but current engine search algorithm
expects only one.
This can be fixed by first looking for output port id and selecting
matching input by subtracting 1 for the next round. This work even if
there is only one input and output.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-11-jernej.skrabec@siol.net
TV TCONs (channel 1 only) are always connected to TV or HDMI encoder.
Because of that, all output endpoints on such TCON node will point to a
encoder which is part of component framework.
Correct current graph traversing algorithm in such way that it doesn't
skip output enpoints with id 0 on TV TCONs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-10-jernej.skrabec@siol.net
TCON TOP is different from other nodes in graph by having 3 input and 3
output ports. Additionally, connection to TV TCON might lead back to
HDMI mux input port, creating loops.
Add support for traversing such graph.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-9-jernej.skrabec@siol.net
Until now, each node has one input port and one output port. However,
with TCON TOP this is no longer true. It has 3 input and 3 output ports.
In order to prepare to this situation, split out the code which checks
all endpoints in input port and adds available components to fifo.
This patch doesn't do any functional change.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-8-jernej.skrabec@siol.net
sun4i_drv_add_endpoints() has a memory leak since it uses of_node_put()
when remote is equal to NULL and does nothing when remote has a valid
pointer.
Invert the logic to fix memory leak.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-7-jernej.skrabec@siol.net
As already described in DT binding, TCON TOP is responsible for
configuring display pipeline. In this initial driver focus is on HDMI
pipeline, so TVE and LCD configuration is not implemented.
Implemented features:
- HDMI source selection
- clock driver (TCON and DSI gating)
- connecting mixers and TCONS
Something similar also existed in previous SoCs, except that it was part
of first TCON.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-6-jernej.skrabec@siol.net
Currently, amdgpu_do_flip() spinlocks crtc->dev->event_lock and
releases it only after committing updates to the stream.
dc_commit_updates_for_stream() should be moved out of
spinlock for the below reasons:
1. event_lock is supposed to protect access to acrct->pflip_status _only_
2. dc_commit_updates_for_stream() has potential sleep's
and also its not appropriate to be in an atomic state
for such long sequences of code.
Signed-off-by: Shirish S <shirish.s@amd.com>
Suggested-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Support new VCN FW version naming convention:
[31, 28] for VEP interface major version if applicable
[27, 24] for decode interface major version
[23, 20] for encode interface major version
[19, 12] for encode interface minor version
[11, 0] for firmware revision
Bit 20-23, it is encode major and non-zero for new naming convention.
This field is part of version minor and DRM_DISABLED_FLAG in old naming
convention. Since the latest version minor is 0x5B and DRM_DISABLED_FLAG
is zero in old naming convention, this field is always zero so far.
These four bits are used to tell which naming convention is present.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Fang, Peter <Peter.Fang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Here is the UBSAN dump:
[ 3.866656] index 2 is out of range for type 'amdgpu_uvd_inst [2]'
[ 3.866693] Workqueue: events work_for_cpu_fn
[ 3.866702] Call Trace:
[ 3.866710] dump_stack+0x85/0xc5
[ 3.866719] ubsan_epilogue+0x9/0x40
[ 3.866727] __ubsan_handle_out_of_bounds+0x89/0x90
[ 3.866737] ? rcu_read_lock_sched_held+0x58/0x60
[ 3.866746] ? __kmalloc+0x26c/0x2d0
[ 3.866846] amdgpu_fence_driver_start_ring+0x259/0x280 [amdgpu]
[ 3.866896] amdgpu_ring_init+0x12c/0x710 [amdgpu]
[ 3.866906] ? sprintf+0x42/0x50
[ 3.866956] amdgpu_gfx_kiq_init_ring+0x1bc/0x3a0 [amdgpu]
[ 3.867009] gfx_v8_0_sw_init+0x1ad3/0x2360 [amdgpu]
[ 3.867062] ? smu7_init+0xec/0x160 [amdgpu]
[ 3.867109] amdgpu_device_init+0x112c/0x1dc0 [amdgpu]
'ring->me' might be set as 2 with 'amdgpu_gfx_kiq_init_ring', that would
cause out of range for 'amdgpu_uvd_inst[2]'.
v2: simplified with ring type
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds a new driver for display panels that use the Ilitek ILI9341
controller. It currently supports a single display panel, namely
the YX240QV29-T (e.g. Adafruit 2.4" TFT).
The init sequence is from the Adafruit Python library for the ILI9341
controller. https://github.com/adafruit/Adafruit_Python_ILI9341
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525193623.15533-5-david@lechnology.com
fb is being dereferenced before it is null checked, hence there
is a potential null pointer dereference.
Fix this by moving the pointer dereference after fb has been
properly null checked at line 74: if (!fb)
Addresses-Coverity-ID: 1470169 ("Dereference before null check")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625121844.GA12466@embeddedor.com
If 'platform_get_resource_byname()' fails, we should release some resources
before leaving, as already done in the other error handling path of the
function.
Fixes: acaa3f13b8 ("drm/meson: Fix potential NULL dereference in meson_drv_bind_master()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611165335.24542-1-christophe.jaillet@wanadoo.fr
This patch unifies the naming of DRM functions for reference counting
of struct drm_gem_object. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <contact@tzimmermann.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625152148.29555-1-contact@tzimmermann.org
The driver doesn't support scaling, but when an atomic test is done
it repeatedly spits out this warning which isn't particularly useful.
So just remove the error message.
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Cc: Chen Feng <puck.chen@hisilicon.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Peter Griffin <peter.griffin@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1529622076-20386-1-git-send-email-john.stultz@linaro.org
Make ioctl wrappers for functions that will be used by the in-kernel API.
The following functions are touched:
- drm_mode_create_dumb_ioctl()
- drm_mode_destroy_dumb_ioctl()
- drm_mode_addfb()
- drm_mode_rmfb()
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618141739.48151-4-noralf@tronnes.org
Rather than doing drm_file allocation/destruction right in the fops, lets
provide separate helpers. This decouples drm_file management from the
still-mandatory drm-fops. It prepares for use of drm_file without the
fops, both by possible separate fops implementations and APIs (not that I
am aware of any such plans), and more importantly from in-kernel use where
no real file is available.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618141739.48151-2-noralf@tronnes.org
Some functions are unused after removal of the kmap_atomic
DMA-buf interface.
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: f664a52695 ("dma-buf: remove kmap_atomic interface")
Link: https://patchwork.freedesktop.org/series/45245/
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
start / last / max_entries are numbers of GPU pages, pfn / count are
numbers of CPU pages. Convert between them accordingly.
Fixes badness on systems with > 4K page size.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/106258
Reported-by: Matt Corallo <freedesktop@bluematt.me>
Tested-by: foxbat@ruin.net
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes a regression I accidentally reduced that was picked up by
kasan, where we were checking the CRTC atomic states after DRM's helpers
had already freed them. Example:
==================================================================
BUG: KASAN: use-after-free in amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu]
Read of size 1 at addr ffff8803a697b071 by task kworker/u16:0/7
CPU: 7 PID: 7 Comm: kworker/u16:0 Tainted: G O 4.18.0-rc1Lyude-Upstream+ #1
Hardware name: HP HP ZBook 15 G4/8275, BIOS P70 Ver. 01.21 05/02/2018
Workqueue: events_unbound commit_work [drm_kms_helper]
Call Trace:
dump_stack+0xc1/0x169
? dump_stack_print_info.cold.1+0x42/0x42
? kmsg_dump_rewind_nolock+0xd9/0xd9
? printk+0x9f/0xc5
? amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu]
print_address_description+0x6c/0x23c
? amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu]
kasan_report.cold.6+0x241/0x2fd
amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu]
? commit_planes_to_stream.constprop.45+0x13b0/0x13b0 [amdgpu]
? cpu_load_update_active+0x290/0x290
? finish_task_switch+0x2bd/0x840
? __switch_to_asm+0x34/0x70
? read_word_at_a_time+0xe/0x20
? strscpy+0x14b/0x460
? drm_atomic_helper_wait_for_dependencies+0x47d/0x7e0 [drm_kms_helper]
commit_tail+0x96/0xe0 [drm_kms_helper]
process_one_work+0x88a/0x1360
? create_worker+0x540/0x540
? __sched_text_start+0x8/0x8
? move_queued_task+0x760/0x760
? call_rcu_sched+0x20/0x20
? vsnprintf+0xcda/0x1350
? wait_woken+0x1c0/0x1c0
? mutex_unlock+0x1d/0x40
? init_timer_key+0x190/0x230
? schedule+0xea/0x390
? __schedule+0x1ea0/0x1ea0
? need_to_create_worker+0xe4/0x210
? init_worker_pool+0x700/0x700
? try_to_del_timer_sync+0xbf/0x110
? del_timer+0x120/0x120
? __mutex_lock_slowpath+0x10/0x10
worker_thread+0x196/0x11f0
? flush_rcu_work+0x50/0x50
? __switch_to_asm+0x34/0x70
? __switch_to_asm+0x34/0x70
? __switch_to_asm+0x40/0x70
? __switch_to_asm+0x34/0x70
? __switch_to_asm+0x40/0x70
? __switch_to_asm+0x34/0x70
? __switch_to_asm+0x40/0x70
? __schedule+0x7d6/0x1ea0
? migrate_swap_stop+0x850/0x880
? __sched_text_start+0x8/0x8
? save_stack+0x8c/0xb0
? kasan_kmalloc+0xbf/0xe0
? kmem_cache_alloc_trace+0xe4/0x190
? kthread+0x98/0x390
? ret_from_fork+0x35/0x40
? ret_from_fork+0x35/0x40
? deactivate_slab.isra.67+0x3c4/0x5c0
? kthread+0x98/0x390
? kthread+0x98/0x390
? set_track+0x76/0x120
? schedule+0xea/0x390
? __schedule+0x1ea0/0x1ea0
? wait_woken+0x1c0/0x1c0
? kasan_unpoison_shadow+0x30/0x40
? parse_args.cold.15+0x17a/0x17a
? flush_rcu_work+0x50/0x50
kthread+0x2d4/0x390
? kthread_create_worker_on_cpu+0xc0/0xc0
ret_from_fork+0x35/0x40
Allocated by task 1124:
kasan_kmalloc+0xbf/0xe0
kmem_cache_alloc_trace+0xe4/0x190
dm_crtc_duplicate_state+0x78/0x130 [amdgpu]
drm_atomic_get_crtc_state+0x147/0x410 [drm]
page_flip_common+0x57/0x230 [drm_kms_helper]
drm_atomic_helper_page_flip+0xa6/0x110 [drm_kms_helper]
drm_mode_page_flip_ioctl+0xc4b/0x10a0 [drm]
drm_ioctl_kernel+0x1d4/0x260 [drm]
drm_ioctl+0x433/0x920 [drm]
amdgpu_drm_ioctl+0x11d/0x290 [amdgpu]
do_vfs_ioctl+0x1a1/0x13d0
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x6f/0xb0
do_syscall_64+0x147/0x440
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 1124:
__kasan_slab_free+0x12e/0x180
kfree+0x92/0x1a0
drm_atomic_state_default_clear+0x315/0xc40 [drm]
__drm_atomic_state_free+0x35/0xd0 [drm]
drm_atomic_helper_update_plane+0xac/0x350 [drm_kms_helper]
__setplane_internal+0x2d6/0x840 [drm]
drm_mode_cursor_universal+0x41e/0xbe0 [drm]
drm_mode_cursor_common+0x49f/0x880 [drm]
drm_mode_cursor_ioctl+0xd8/0x130 [drm]
drm_ioctl_kernel+0x1d4/0x260 [drm]
drm_ioctl+0x433/0x920 [drm]
amdgpu_drm_ioctl+0x11d/0x290 [amdgpu]
do_vfs_ioctl+0x1a1/0x13d0
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x6f/0xb0
do_syscall_64+0x147/0x440
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The buggy address belongs to the object at ffff8803a697b068
which belongs to the cache kmalloc-1024 of size 1024
The buggy address is located 9 bytes inside of
1024-byte region [ffff8803a697b068, ffff8803a697b468)
The buggy address belongs to the page:
page:ffffea000e9a5e00 count:1 mapcount:0 mapping:ffff88041e00efc0 index:0x0 compound_mapcount: 0
flags: 0x8000000000008100(slab|head)
raw: 8000000000008100 ffffea000ecbc208 ffff88041e000c70 ffff88041e00efc0
raw: 0000000000000000 0000000000170017 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8803a697af00: fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8803a697af80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8803a697b000: fc fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb
^
ffff8803a697b080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8803a697b100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
So, we fix this by counting the number of CRTCs this atomic commit disabled
early on in the function before their atomic states have been freed, then use
that count later to do the appropriate number of RPM puts at the end of the
function.
Acked-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Fixes: 97028037a3 ("drm/amdgpu: Grab/put runtime PM references in atomic_commit_tail()")
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Michel Dänzer <michel@daenzer.net>
Reported-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
