When the device is powered up, some (older) firmware versions fail to work
properly if we send commands before the boot is complete (everything is OK
when the device is hot-plugged). The firmware indicates its ready status by
putting the link up.
Newer firmwares delay the first command so they don't suffer from this problem.
They also report the link being always up.
Wait for firmware to become ready (link up) before sending any commands and/or
data.
This also allows lowering CMD_TIMEOUT value to a reasonable time.
Tested with 4.1.0.9 (old) and 4.1.0.30 (new) firmware versions.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 11ad714b98 because
it breaks cx82310_eth.
The custom USB_DEVICE_CLASS macro matches
bDeviceClass, bDeviceSubClass and bDeviceProtocol
but the common USB_DEVICE_AND_INTERFACE_INFO matches
bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are
not specified.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Oliver Neukum <oliver@neukum.org>
CC: Steve Glendinning <steve.glendinning@shawell.net>
CC: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hub-initiated LPM is not good for USB communications devices. Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.
If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data. Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.
The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host. In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.
Set the disable_hub_initiated_lpm flag for for all USB communications
drivers. I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This converts the drivers in drivers/net/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: Yoann DI-RUZZA <y.diruzza@lim.eu>
Cc: George <george0505@realtek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Empty received URBs are currently counted as errors but the device sends them
sometimes as part of regular traffic - so remove this check.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix that usb_string() return value is not checked for error (negative value).
Also change the ignore message a bit and lower its level to info.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces cx82310_eth driver - driver for USB ethernet port of
ADSL routers based on Conexant CX82310 chips. Such routers usually have
ethernet port(s) too which are bridged together with the USB ethernet port,
allowing the USB-connected machine to communicate to the network (and also
internet through the ADSL, of course).
This is my first driver, so please check thoroughly. As there's no protocol
documentation, it was done with usbsnoop dumps from Windows driver, some
parts (the commands) inspired by cxacru driver and also other usbnet drivers.
The driver passed my testing - some real work and also pings sized from 0 to
65507 B.
The only problem I found is the ifconfig error counter. When I return 0 (or 1
but empty skb) from rx_fixup(), usbnet increases the error counter although
it's not an error condition (because packets can cross URB boundaries). Maybe
the usbnet should be fixed to allow rx_fixup() to return empty skbs (or some
other value, e.g. 2)?
The USB ID of my device is 0x0572:0xcb01 which conflicts with some ADSL modems
using cxacru driver (they probably use the same chipset but simpler
firmware). The modems seem to use bDeviceClass 0 and iProduct "ADSL USB
MODEM", my router uses bDeviceClass 255 and iProduct "USB NET CARD". The
driver matches only devices with class 255 and checks for the iProduct string
during init. I already posted a patch for the cxacru driver to ignore these
devices.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
