Haikou is a Qseven and μQseven baseboard featuring PCIe, USB3 and a
video connector for MIPI-DSI/CSI and eDP adapter.
This dts is for usage with the RK3399-Q7 SoM Puma.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The ROCK64 is a credit card size 4K60P HDR Media Board Computer using the
Rockchip RK3328 Quad-Core ARM Cortex A53 64-Bit Processor and supporting
up to 4GB 1600MHz LPDDR3 memory. It provides eMMC module socket, MicroSD
Card slot, Pi-2 Bus, Pi-P5+ Bus, USB 3.0 and many others peripheral
devices interface for makers to integrate with sensors and devices.
The devicetree currently supports basic peripherals, with more to be
added later on.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds and enable the operating points that have been tested and are
currently supported by the SoC. This also adds clocks for ARMCLKL and
ARMCLKB.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK805 consists of 4 DCDCs, 3 LDOs. It's different from RK808
and RK818 that there are 2 output only GPIOs, we should add
properties "gpio-controller" and "gpio-cells = <2>".
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Currently we are assigning mic irq to rt5514 i2c driver, which is wrong.
Assign it to rt5514 spi driver instead.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We need to init vop aclk and hclk incase the U-Boot does not do
the initialize.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There are 4 pwm channels built in rk3328 soc, need to configure
the both APB clock and bus clock.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to rt5514 dt-binding, it should be "realtek,dmic-init-delay-ms".
Fixes: 48f4d9796d (arm64: dts: rockchip: add Gru/Kevin DTS)
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3399 USB DWC3 controller has a issue that FS/LS devices not
recognized if inserted through USB 3.0 HUB. It's because that
the inter-packet delay between the SSPLIT token to SETUP token
is about 566ns, more then the USB spec requirement.
This patch adds a quirk "snps,dis-tx-ipgap-linecheck-quirk" to
disable the u2mac linestate check to decrease the SSPLIT token
to SETUP token inter-packet delay from 566ns to 466ns.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When adding the rk3399 sapphire som, two more of the recently removed
num-slots properties of dw-mmc nodes slipped in.
Remove them again.
Fixes: 8164a84cca ("arm64: dts: rockchip: Add support for rk3399 sapphire SOM")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
add thermal zone and dynamic CPU power coefficients for rk3328
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
add tsadc needed main information for rk3328 SoC.
50000Hz is the max clock rate supported by tsadc module.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the rk3399 excavator main board.
This board works in a combination with the sapphire SOM.
This board have been sold as the rk3399 evaluation board for commercial customers.
You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the rk3399 sapphire SOM board.
This board works in a combination with the excavator main board.
You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an hdmi node, and also add hdmi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an mipi node, and also add mipi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an edp node, and also add edp endpoints to vopb and vopl
output port nodes.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
1. add pd node for RK3399 Soc
2. create power domain tree
3. add qos node for domain
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add devicetree nodes for rk3399 VOP (Video Output Processors), and the
top level display-subsystem root node.
Later patches add endpoints (eDP, HDMI, MIPI, etc) that attach to the
VOPs' output ports.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add opp tables for cpu cluster0 and cluster1 by including
rk3399-opp.dtsi.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch updates the dynamic-power-coefficient for big cluster on
rk3399 SoCs.
The dynamic power consumption of the CPU is proportional to the square of
the Voltage (V) and the clock frequency (f). The coefficient is used to
calculate the dynamic power as below -
Pdyn = dynamic-power-coefficient * V^2 * f
Where Voltage is in uV, frequency is in MHz.
As the following is the tested data on rk3399's big cluster.
frequency(MHz) Voltage(V) Current(mA) Dynamic-power-coefficient
24 0.8 15
48 0.8 23 ~417
96 0.8 40 ~443
216 0.8 82 ~438
312 0.8 115 ~430
408 0.8 150 ~455
So the dynamic-power-coefficient average value is about 436.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This allows basic support for SD highspeed cards but no UHS-I mode
got ready due to the propagated defer-probe error from RK805.
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the core grf subnode for the io-domain controller.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Kill these two pinctrl reference totally from rk3399 as it
never work indeed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
pcie_clkreqn actually doesn't work at all, so replace it with
pcie_clkreqn_cpm.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch enables the gpu and adds the mali-supply power for RK3399-GRU
devices.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add Mali GPU device tree node for the RK3399 SoCs, with devfreq
opp table.
RK3399 and RK3399-OP1 SoCs have a different recommendation table with
gpu opp. Also, the ARM's mali driver found on
https://developer.arm.com/products/software/mali-drivers/midgard-kernel.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
keep-power-in-suspend was invented for SDIO only, so it should
not be used for eMMC node.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We deprecated the "num-slots" property now and plan to get
rid of it finally. Just move a step to cleanup it from DT.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
pcie_clkreqn actually doesn't work at all, so replace it with
pcie_clkreqn_cpm.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The SdioAudio power domain includes the i2s/spdif/spi5/sdio.
So this patch adds the pd control for rk3399 i2s/spdif/spi5/sdio, in order
to save more power consumption.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockchip's RK3328 evaluation board has one usb2 otg controller
and one usb2 host controller which consist of EHCI and OHCI.
Each usb controller connects with one usb2 phy port through
UTMI+ interface. Let's enable them to support usb2 on RK3328
evaluation board.
Signed-off-by: William Wu <william.wu@rock-chips.com>
[restructured enablement of u2phy subnodes]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Provide the dynamic power coefficient of the big and little CPU
clusters. These numbers are currently in use on the Samsung Chromebook
Plus ("Kevin").
The power allocator thermal governor doesn't know how to do anything if
it doesn't get power parameters from its cooling devices (in this case,
CPUfreq). So this effectively enables the power-allocator governor.
Signed-off-by: Brian Norris <briannorris@chromium.org>
[set the property in each core node]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Gru device tree currently contains entries for the regulators
ppvar_bigcpu, ppvar_litcpu, ppvar_gpu and ppvar_centerlogic; however,
the regulators have not been enabled, due to the lack of binding and driver
support for keeping the over-voltage protection (OVP) at bay and
preventing unintended regulator shutdowns on voltage downshifts.
Now, the vctrl regulator driver has been merged, along with new bindings
for asymmetric settling time. The driver is OVP aware, it splits larger
voltage decreases in multiple steps when necessary and adds required
delays.
This change renames each of the aforementioned regulators to
<orig_name>_pwm and adds a new vctrl regulator named <orig_name>.
The vctrl regulators use the voltage of their corresponding PWM regulator
as control voltage. The OVP related values are empirical and stem from
the Chrome OS kernel tree.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
[fixed node names and parent supplies of gpu and centerlogic]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Gru derivatives besides Kevin have slightly different voltage ranges for
their CPU regulators. Let's keep the base Gru file accurate and let
Kevin override.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
replace all occurrences of sdmcc with sdmmc in the arm64 rockchip
devicetree files.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
Device-tree updates for arm64 platforms. For the first time I can
remember, this is actually larger than the corresponding branch for
32-bit platforms overall, though that has more individual changes.
A significant portion this time is due to added machine support:
- Initial support for the Realtek RTD1295 SoC, along with the Zidoo
X9S set-top-box
- Initial support for Actions Semi S900 and the Bubblegum-96
single-board-cёmputer.
- Rockchips support for the rk3399-Firefly single-board-computer
gets added, this one stands out for being relatively fast,
affordable and well₋supported, compared to many boards that
only fall into one or two of the above categories.
- Mediatek gains support for the mt6797 mobile-phone SoC platform
and corresponding evaluation board.
- Amlogic board support gets added for the NanoPi K2 and S905x
LibreTech CC single-board computers and the R-Box Pro set-top-box
- Allwinner board support gets added for the OrangePi Win,
Orangepi Zero Plus 2, NanoPi NEO2 and Orange Pi Prime single
board computers and the SoPine system-on-module.
- Renesas board support for Salvator-XS and H3ULCB
automotive development systems.
- Socionext Uniphier board support for LD11-global and LD20-global,
whatever those may be.
- Broadcom adds support for the new Stingray communication processor
in its iProc family, along with two reference boards.
Other updates include:
- For the hisicon platform, support for Hi3660-Hikey960 gets
extended significantly.
- Lots of smaller updates for Renesas, Amlogic, Rockchip, UniPhier,
Broadcom, Allwinner, Hisilicon, Qualcomm, Marvell, and NXP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=E8pa
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"Device-tree updates for arm64 platforms. For the first time I can
remember, this is actually larger than the corresponding branch for
32-bit platforms overall, though that has more individual changes.
A significant portion this time is due to added machine support:
- Initial support for the Realtek RTD1295 SoC, along with the Zidoo
X9S set-top-box
- Initial support for Actions Semi S900 and the Bubblegum-96
single-board-cёmputer.
- Rockchips support for the rk3399-Firefly single-board-computer gets
added, this one stands out for being relatively fast, affordable
and well₋supported, compared to many boards that only fall into one
or two of the above categories.
- Mediatek gains support for the mt6797 mobile-phone SoC platform and
corresponding evaluation board.
- Amlogic board support gets added for the NanoPi K2 and S905x
LibreTech CC single-board computers and the R-Box Pro set-top-box
- Allwinner board support gets added for the OrangePi Win, Orangepi
Zero Plus 2, NanoPi NEO2 and Orange Pi Prime single board computers
and the SoPine system-on-module.
- Renesas board support for Salvator-XS and H3ULCB automotive
development systems.
- Socionext Uniphier board support for LD11-global and LD20-global,
whatever those may be.
- Broadcom adds support for the new Stingray communication processor
in its iProc family, along with two reference boards.
Other updates include:
- For the hisicon platform, support for Hi3660-Hikey960 gets extended
significantly.
- Lots of smaller updates for Renesas, Amlogic, Rockchip, UniPhier,
Broadcom, Allwinner, Hisilicon, Qualcomm, Marvell, and NXP"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (243 commits)
ARM64: dts: marvell: armada37xx: Fix timer interrupt specifiers
Revert "arm64: dts: marvell: add dma-mask in crypto nodes for 7k/8k"
arm64: dts: mediatek: don't include missing file
ARM64: dts: meson-gxl: Add Libre Technology CC support
dt-bindings: arm: amlogic: Add Libre Technology CC board
dt-bindings: add Libre Technology vendor prefix
arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K
arm64: dts: zte: Use - instead of @ for DT OPP entries
arm64: dts: marvell: add gpio support for Armada 7K/8K
arm64: dts: marvell: add pinctrl support for Armada 7K/8K
arm64: dts: marvell: use new binding for the system controller on cp110
arm64: dts: marvell: remove *-clock-output-names on cp110
arm64: dts: marvell: use new bindings for xor clocks on ap806
arm64: dts: marvell: mcbin: enable the mdio node
arm64: dts: Add Actions Semi S900 and Bubblegum-96
dt-bindings: Add vendor prefix for uCRobotics
arm64: dts: marvell: add xmdio nodes for 7k/8k
arm64: dts: marvell: add a comment on the cp110 slave node status
arm64: dts: marvell: remove cpm crypto nodes from dts files
arm64: dts: marvell: cp110: enable the crypto engine at the SoC level
...
Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates, and
a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only reported
issue being a merge problem with this tree and the jc-docs tree in the
w1 documentation area. The fix should be obvious for what to do when it
happens, if not, we can send a follow-up patch for it afterward.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpXKA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynLrQCdG9SxRjAbOd6pT9Fr2NAzpUG84YsAoLw+I3iO
EMi60UXWqAFJbtVMS9Aj
=yrSq
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates,
and a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only
reported issue being a merge problem with this tree and the jc-docs
tree in the w1 documentation area"
* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (147 commits)
misc: apds990x: Use sysfs_match_string() helper
mei: drop unreachable code in mei_start
mei: validate the message header only in first fragment.
DocBook: w1: Update W1 file locations and names in DocBook
mux: adg792a: always require I2C support
nvmem: rockchip-efuse: add support for rk322x-efuse
nvmem: core: add locking to nvmem_find_cell
nvmem: core: Call put_device() in nvmem_unregister()
nvmem: core: fix leaks on registration errors
nvmem: correct Broadcom OTP controller driver writes
w1: Add subsystem kernel public interface
drivers/fsi: Add module license to core driver
drivers/fsi: Use asynchronous slave mode
drivers/fsi: Add hub master support
drivers/fsi: Add SCOM FSI client device driver
drivers/fsi/gpio: Add tracepoints for GPIO master
drivers/fsi: Add GPIO based FSI master
drivers/fsi: Document FSI master sysfs files in ABI
drivers/fsi: Add error handling for slave
drivers/fsi: Add tracepoints for low-level operations
...
