We need to test for 24xx not 242x. Otherwise interrupts won't work.
Reported-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cache ownership must be acquired by reading/writing data from the
cache line to make cache operation have the desired effect on the
SMP MPCore CPU. However, the ownership is never acquired in the
v6_dma_inv_range function when cleaning the first line and
flushing the last one, in case the address is not aligned
to D_CACHE_LINE_SIZE boundary.
Fix this by reading/writing data if needed, before performing
cache operations.
While at it, fix v6_dma_flush_range to prevent RWFO outside
the buffer.
Cc: stable@kernel.org
Signed-off-by: Valentine Barshak <vbarshak@mvista.com>
Signed-off-by: George G. Davis <gdavis@mvista.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Because the nwfpe support is unlikely to be used on new platforms
and requires CONFIG_OABI_COMPAT, which is not generally used with
ARMv7+, we shouldn't expect to build nwfpe support into a Thumb-2
kernel.
At present, nwfpe contains assembly code which isn't Thumb-2
compatible, and for now it doesn't appear useful to port this
code.
All ARMv7-A/R platforms necessarily have VFPv3 hardware floating-
point natively, making emulation unnecessary.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes sense, because Thumb-2 code can't execute on plain
ARMv6 processors.
This will avoid accidentally configuring a broken kernel where the
config otherwise would allow multiple architecture versions to
coexist in the same kernel.
Not adding !CPU_V5 etc., because the chance of anyone trying to
put v5 and v7 in the same kernel is low, and I'm not aware of
any mach which can do this. These could be added later if it
matters.
Note that the rules may need to be refined if support for the
ARM1156J(F)-S processor is later added to the kernel, since this
processor supports the rare ARMv6T2 extensions, which add support
for Thumb-2 and a few other ARMv7 features.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current implementation of the v7_coherent_*_range function assumes
that the D and I cache lines have the same size, which is incorrect
architecturally. This patch adds the icache_line_size macro which reads
the CTR register. The main loop in v7_coherent_*_range is split in two
independent loops or the D and I caches. This also has the performance
advantage that the DSB is moved outside the main loop.
Reported-by: Kevin Sapp <ksapp@quicinc.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current implementation of the dcache_line_size macro reads the L1
cache size from the CCSIDR register. This, however, is not guaranteed to
be the smallest cache line in the cache hierarchy. The patch changes to
the macro to use the more architecturally correct CTR register.
Reported-by: Kevin Sapp <ksapp@quicinc.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After Charu's GPIO hwmod patches, GPIO initialization on N800 emits
the following messages for all GPIO banks:
omap_hwmod: gpio1: cannot be enabled (3)
This is due to OMAP24XX_ST_GPIOS_SHIFT being defined as a bitmask.
Fix this and also fix two other macros that had the same problem.
Thanks to Tony Lindgren <tony@atomide.com> for originally reporting
this bug.
Signed-off-by: Paul Walmsley <paul@pwsan.com
Cc: Charulatha Varadarajan <charu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Please use omap1_defconfig instead, or search online
for a more optimized defconfig for your omap1 board.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap1_defconfig this should be eventually usable for booting
all omap1 machines. Generated based on:
$ grep ARCH_OMAP1=y arch/arm/configs/* | cut -d: -f1 | xargs cat | \
sort | uniq >> arch/arm/configs/omap1_defconfig
Then change few things manually, like use Nokia 770 CONFIG_CMDLINE
as it does not allow setting it in the bootloader.
Finally ran make savedefconfig on it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise multi-omap1 support for omap1 won't work as the cpu_class_is_omap1()
won't work until the SoC is detected.
Note that eventually these will go away, please use ioremap + read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 0d8e2d0dad (OMAP2+: PM/serial:
hold console semaphore while OMAP UARTs are disabled) added use of the
console semaphore to protect UARTs from being accessed after disabled
during idle, but this causes problems in suspend.
During suspend, the console semaphore is acquired by the console
suspend method (console_suspend()) so the try_acquire_console_sem()
will always fail and suspend will be aborted.
To fix, introduce a check so the console semaphore is only attempted
during idle, and not during suspend. Also use the same check so that
the console semaphore is not prematurely released during resume.
Thanks to Paul Walmsley for suggesting adding the same check during
resume.
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: Jean Pihet <j-pihet@ti.com>
Tested-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kernel was failing to boot on omap1611 based OSK boards due to
mis-configured SRAM size. Existing code was using a hard-coded value
for 250k, which was then rounded down by PAGE_SIZE. Increasing this to
256k allows kernel to boot on omap1611 SoCs.
Problem reported by and initial fix suggested by Tim Bird.
Thanks to Tony Lindgren for helping diagnose the problem to being
specific to OMAP1611 and not affecting OMAP1610/OMAP1623.
Reported-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize asm_irq_flags in omap_init_irq and use it in
get_irqnr_and_base to detect between omap7xx and omap15xx/16xx.
Note that both INT_1510_IH2_IRQ and INT_1510_IH2_IRQ are defined
as 0, so use INT_1510_IH2_IRQ for both of them.
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't need to repeat the same definitions of the ioremap*(),
once in terms of __arch_ioremap() and again in terms of __arm_ioremap().
Instead, if the platform hasn't provided an __arch_ioremap, define
this to be __arm_ioremap, and only define the ioremap*() set using
__arch_ioremap.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Defining iounmap() with arguments prevents it from being used as a
function pointer, causing platforms to work around this. Instead,
define it to be a simple macro.
Do the same for __arch_io(re|un)map too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
clk_get() return value should be checked with IS_ERR().
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the {set,get}_pull callbacks of the s3c24xx_gpiocfg_default structure
are initalized via s3c_gpio_{get,set}pull_1up. This results in a linker
error when only CONFIG_CPU_S3C2442 is selected:
arch/arm/plat-s3c24xx/built-in.o:(.data+0x13f4): undefined reference to
`s3c_gpio_getpull_1up'
arch/arm/plat-s3c24xx/built-in.o:(.data+0x13f8): undefined reference to
`s3c_gpio_setpull_1up'
The s3c2442 has pulldowns instead of pullups compared to the s3c2440.
The method of controlling them is the same though.
So this patch modifies the existing s3c_gpio_{get,set}pull_1up helper functions
to take an additional parameter deciding whether the pin has a pullup or pulldown.
The s3c_gpio_{get,set}pull_1{down,up} functions then wrap that functions passing
either S3C_GPIO_PULL_UP or S3C_GPIO_PULL_DOWN.
Furthermore this patch sets up the s3c24xx_gpiocfg_default.{get,set}_pull fields
in the s3c244{0,2}_map_io function to the new pulldown helper functions.
Based on patch from "Lars-Peter Clausen" <lars@metafoo.de>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We need to divide the 15xx/16xx offset by 2 for 7xx. Use bank->stride
for that. This allows us to get rid of the duplicate defines for the
MPUIO registers.
Note that this will cause omap-keypad.c driver to not work on 7xx.
However, the right fix there is to move over to matrix_keypad instead
as suggested by Cory Maccarrone <darkstar6262@gmail.com> and
Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>.
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Acked-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement GPIO as a platform device.
GPIO APIs are used in machine_init functions. Hence it is
required to complete GPIO probe before board_init. Therefore
GPIO device register and driver register are implemented as
postcore_initcalls.
omap_gpio_init() does nothing now and this function would be
removed in the next patch as it's usage is spread across most
of the board files.
Inorder to convert GPIO as platform device, modifications are
required in clockxxxx_data.c file for OMAP1 so that device names
can be used to obtain clock instead of getting clocks by
name/NULL ptr.
Use runtime pm APIs (pm_runtime_put*/pm_runtime_get*) for enabling
or disabling the clocks, modify sysconfig settings and remove usage
of clock FW APIs.
Note 1: Converting GPIO driver to use runtime PM APIs is not done as a
separate patch because GPIO clock names are different for various OMAPs
and are different for some of the banks in the same CPU. This would need
usage of cpu_is checks and bank id checks while using clock FW APIs in
the gpio driver. Hence while making GPIO a platform driver framework,
PM runtime APIs are used directly.
Note 2: While implementing GPIO as a platform device, pm runtime APIs
are used as mentioned above and modification is not done in gpio's
prepare for idle/ resume after idle functions. This would be done
in the next patch series and GPIO driver would be made to use dev_pm_ops
instead of sysdev_class in that series only.
Due to the above, the GPIO driver implicitly relies on
CM_AUTOIDLE = 1 on its iclk for power management to work, since the
driver never disables its iclk.
This would be taken care in the next patch series (see Note 3 below).
Refer to
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg39112.html
for more details.
Note 3: only pm_runtime_get_sync is called in gpio's probe() and
pm_runtime_put* is never called. This is to make the implementation
similar to the existing GPIO code. Another patch series would be sent
to correct this.
In OMAP3 and OMAP4 gpio's debounce clocks are optional clocks. They
are enabled/ disabled whenever required using clock framework APIs
TODO:
1. Cleanup the GPIO driver. Use function pointers and register
offest pointers instead of using hardcoded values
2. Remove all cpu_is_ checks and OMAP specific macros
3. Remove usage of gpio_bank array so that only
instance specific information is used in driver code
4. Rename 'method'/ avoid it's usage
5. Fix the non-wakeup gpios handling for OMAP2430, OMAP3 & OMAP4
6. Modify gpio's prepare for idle/ resume after idle functions
to use runtime pm implentation.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Basak, Partha <p-basak2@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated for bank specific revision and updated boards]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use omap_device_build() API to do platform_device_register of
GPIO devices. For OMAP2+ chips, the device specific data defined
in the centralized hwmod database will be used.
gpio_init needs to be done before machine_init functions access
gpio APIs. Hence gpio_init is made as a postcore_initcall.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Basak, Partha <p-basak2@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPIO hwmod data for OMAP4
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPIO hwmod data for OMAP3
Also remove "omap34xx.h" header file as it is not required
anymore.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPIO hwmod data for OMAP2430
Also remove "omap24xx.h" header file as it is not required
anymore.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPIO hwmod data for OMAP2420 and add the required
GPIO device attributes in the gpio header file
Also remove "omap24xx.h" header file as it is not required
anymore.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for handling OMAP7xx specific gpio_init by
providing platform device data and doing device registration.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for handling OMAP16xx specific gpio_init by
providing platform device data and doing device registration.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for handling OMAP15xx specific gpio_init by
providing platform device data and doing device registration.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise GPIO init on 16xx may try to access uninitialized GPIO
bank as the MPUIO bank does not have a revision register.
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Prepare for implementing GPIO as a platform driver.
Modifies omap_gpio_init() to make use of omap_gpio_chip_init()
and omap_gpio_mod_init(). omap_gpio_mod_init() does the module init
by clearing the status register and initializing the GPIO control register.
omap_gpio_chip_init() initializes the chip request, free, get, set and
other function pointers and sets the gpio irq handler.
This is only to reorganize the code so that the "omap gpio platform driver
implementation patch" looks cleaner and better to review.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like some boards are calling gpio_request from init_irq.
This will make the request_irq fail, as GPIO will be initialized
as postcore_initcall.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Using true/false instead of 1/0 to update the free variable.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Function omap_mcbsp_probe allocates struct omap_mcbsp *mcbsp but it is not
freed in omap_mcbsp_remove. Fix this, remove unneeded structure cleanups
and clk_disable calls since they are not needed here.
This is not problem currently but becomes if the mcbsp driver is ever
modularized.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Value of "isr_reg" pointer is depend on configuration and GPIO method.
Potentially it may have NULL value and it is dereferenced later
in code. Warning and exit from function are added in this case.
Signed-off-by: Evgeny Kuznetsov <EXT-Eugeny.Kuznetsov@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In some cases we can get error function `omap2_i2c_add_bus':
arch/arm/plat-omap/i2c.c:136: undefined reference to `omap2_i2c_mux_pins'
arch/arm/plat-omap/i2c.c:141: undefined reference to `omap_hwmod_lookup'
arch/arm/plat-omap/i2c.c:157: undefined reference to `omap_device_build'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 4d17aeb1c5 ("OMAP: I2C: split
device registration and convert OMAP2+ to omap_device") broke I2C on
OMAP1. The following messages appear at boot:
i2c_omap i2c_omap.1: failure requesting irq 0
i2c_omap: probe of i2c_omap.1 failed with error -22
Investigation revealed that a chunk of code is missing from the
original plat-omap/i2c.c file which configured the IRQ and base address
for the I2C block on OMAP1. Upon adding this back, the OMAP1 I2C block
seems to initialize correctly.
Thanks to Cory Maccarrone <darkstar6262@gmail.com> for reporting the bug,
and apologies for the breakage.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Tested-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 0ea1293009 ("arm: return both physical and virtual addresses
from addruart") took out the test for MMU on/off but didn't switch the
ldr instructions to no longer be conditionals based on said test.
Fix that.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
clk_get() returns ERR_PTR() on error, not NULL.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated to include err.h to compile on omap1]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch complements ed919b0 "mmc: sdio: fix runtime PM anomalies by
introducing MMC_CAP_POWER_OFF_CARD" by declaring MMC_CAP_POWER_OFF_CARD
on the ZOOM's wl1271 mmc slot.
This is required in order not to break runtime PM support for the wl1271
sdio driver.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6524/1: GIC irq desciptor bug fix
ARM: 6523/1: iop: ensure sched_clock() is notrace
ARM: 6456/1: Fix for building DEBUG with sa11xx_base.c as a module.
ARM: 6519/1: kuser: Fix incorrect cmpxchg syscall in kuser helpers
ARM: 6505/1: kprobes: Don't HAVE_KPROBES when CONFIG_THUMB2_KERNEL is selected
ARM: 6508/1: vexpress: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
ARM: 6507/1: RealView: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
ARM: 6504/1: Thumb-2: Fix long-distance conditional branches in head.S for Thumb-2.
ARM: 6503/1: Thumb-2: Restore sensible zImage header layout for CONFIG_THUMB2_KERNEL
ARM: 6502/1: Thumb-2: Fix CONFIG_THUMB2_KERNEL breakage in compressed/head.S
ARM: 6501/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in mm/proc-v7.S
ARM: 6500/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in kernel/head.S
ARM: 6499/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in bootp/init.S
ARM: 6498/1: vfp: Correct data alignment for CONFIG_THUMB2_KERNEL
ARM: 6497/1: kexec: Correct data alignment for CONFIG_THUMB2_KERNEL
ARM: 6496/1: GIC: Do not try to register more then NR_IRQS interrupts
ARM: cns3xxx: Fix build with CONFIG_PCI=y
gic_set_cpu will directly use irq_desc[]. If CONFIG_SPARSE_IRQ is
enabled, there is no irq_desc[]. So we need use irq_to_desc(irq) to
get the descriptor for irq.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Include sched.h to ensure sched_clock() has the notrace
annotation, and mark any functions it calls as notrace
too.
Include sched.h to ensure sched_clock() has the notrace
annotation, and mark any functions it calls as notrace
too.
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The existing code invokes the syscall with rubbish in r7,
due to what looks like an incorrect literal load idiom.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MACH_MINI2440 entry requires the backlight LED driver, but this
subsystem has not been enabled and the select of LEDS_TRIGGER_BACKLIGHT
alone is insufficient to enable the necessary bits of the LED driver.
Add NEW_LEDS, LEDS_CLASS and LEDS_TRIGGER to the select to allow the
kernel to link.
This fixes the following error:
drivers/built-in.o: In function `led_trigger_set':
/home/ben/linux.git/drivers/leds/led-triggers.c:116: undefined reference to `led_brightness_set'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Wakeup-on-timer code does not have/need debugfs dependency. Move
the function out of debugfs ifdef.
Fixes compile error when CONFIG_DEBUG_FS is disabled but PM debug is
enabled.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When OneNAND support is disabled, the platform code defines NULL
board_onenand_data and empty init function for us. By utilizing this we
can avoid cluttering board files with dummy definitions/wrappers.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When OneNAND support is disabled, the platform code defines NULL
board_onenand_data and empty init function for us. By utilizing this we
can avoid cluttering board files with dummy definitions/wrappers.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_OMAP_MUX is not enabled, we can define board_mux in the header
file instead of forcing every single board to define it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated for combined board-zoom files]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the mailbox detection for OMAP3630 and 2430, also minor
cleanup on conditional ifdef's that could affect it.
Given that 2430 has an iva too, include it, as the same steps
for omap3 apply.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Hiroshi Doyu <hiroshi.doyu@nokia.com>
In the current mailbox driver, the mailbox internal pointer for
callback can be directly manipulated by the Users, so a second
User can easily corrupt the first user's callback pointer.
The initial effort to correct this issue can be referred here:
https://patchwork.kernel.org/patch/107520/
Along with fixing the above stated issue, this patch adds the
flexibility option to register notifications from
multiple readers to the events received on a mailbox instance.
The discussion regarding this can be referred here.
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg30671.html
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Acked-by: Hiroshi Doyu <hiroshi.doyu@nokia.com>
Schedule the Tasklet to send only when mailbox fifo is full and there are
pending messages in kfifo, else send the message directly in the Process
context. This would avoid needless scheduling of Tasklet for every message
transfer
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Acked-by: Hiroshi Doyu <hiroshi.doyu@nokia.com>
Fix the following checkpatch warnings observed in mailbox module.
WARNING: please, no space for starting a line,
excluding comments
+ fail_alloc_rxq:$
WARNING: please, no space for starting a line,
excluding comments
+ fail_alloc_txq:$
WARNING: please, no space for starting a line,
excluding comments
+ fail_request_irq:$
WARNING: line over 80 characters
+ mbox_kfifo_size = max_t(unsigned int, mbox_kfifo_size, sizeof(mbox_msg_t));
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Acked-by: Hiroshi Doyu <hiroshi.doyu@nokia.com>
The variable rq_full flag is a global variable, so if there are multiple
mailbox users there will be conflicts. Now there is a full flag per
mailbox queue.
Reported-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Acked-by: Hiroshi Doyu <hiroshi.doyu@nokia.com>
Access to some registers depends on register access mode
Three different modes are available for OMAP (at least)
• Operational mode LCR_REG[7] = 0x0
• Configuration mode A LCR_REG[7] = 0x1 and LCR_REG[7:0]! = 0xBF
• Configuration mode B LCR_REG[7] = 0x1 and LCR_REG[7:0] = 0xBF
Define access modes and remove redefinitions and magic numbers
in serial drivers (and later in bluetooth driver).
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define MDR1 register serial definitions used in serial and
bluetooth drivers.
Change magic number to ones defined in serial_reg for omap1/2
serial driver.
Remove redefined MDR1 register definitions in omap-serial driver.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Craneboard is a hardware development platform based on the
Sitara AM3517 ARM Cortex - A8 microprocessor device. This is a
low cost reference design.
This patch adds basic board file. Detailed support will follow in
subsequent patches.
[1] http://www.ti.com/arm
[2] http://www.mistralsolutions.com/products/craneboard.php
Signed-off-by: Srinath <srinath@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patches removes a config option that was used to select a FIQ
handler to be build for Amstrad Delta, as required by the on-board serio
interface driver. Not having any problem reports received since it was
introduced in 2.6.35, the FIQ handler can now be built and initialized by
default, thus reqiring no extra config option.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It's easier to understand what that number means and
also avoids problems if we ever have to change it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
They are extremely similar anyway, let's get rid
of one file.
While at that, also remove the empty zoom_config
variable.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The changes are:
- Use 'for' loop instead 'while' loop.
- No need to initialize ret to 0, we're assigning it right after.
- No need to check for onenandcs < GPMC_CS_NUM here, it will always be true.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_board_config_size is implicitly initialized to 0 in
plat-omap/common.c, get_config() won't dereference omap_board_config,
so we can remove the empty igep2_config array.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
for the epson frambuffer support it's CONFIG_FB_S1D13XXX
not CONFIG_FB_S1D135XX
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
as based on http://www.picotux.com/pt200/picotux200.pdf
these board does not have such I/O
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
to be a few more concistant with the other boards
as ek is for evaluation kit and dk for development kit
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Convert the following AT91RM9200-based boards to the new-style UART
initialization:
- Ajeco 1ARM Single Board Computer
- Sperry-Sun KAFA board
- picotux 200
Remove the deprecated at91_init_serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Currently, the kprobes implementation for ARM only supports the ARM
instruction set, so it only works if CONFIG_THUMB2_KERNEL is not
enabled.
Until kprobes is updated to work with Thumb-2, turning it on will
cause horrible things to happen, so this patch disables it for now.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a
result, using these directives in code sections can result in
misaligned data words when building a Thumb-2 kernel
(CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to
assume that fundamental types of word size or above are word-
aligned when accessing them from C. If the data is not really
word-aligned, this can cause impaired performance and stray
alignment faults in some circumstances.
In general, the following rules should be applied when using
data word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned data
words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume that
fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned, this
can cause impaired performance and stray alignment faults in some
circumstances.
In general, the following rules should be applied when using data word
declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 32-bit conditional branches in Thumb-2 have a shorter range
(+/-512K) than their ARM counterparts (+/-32MB). The linker does
not currently generate trampolines to extend the range of these
Thumb-2 conditional branches, resulting in link errors when vmlinux
is sufficiently large, e.g.:
head.o:(.text+0x464): relocation truncated to fit: R_ARM_THM_JUMP19
This patch forces the longer-range, unconditional branch encoding
by use of an explicit IT instruction. The resulting branches are
triggered on the same conditions as before.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The code which makes up the zImage header intends to leave a
32-byte gap followed by a branch to the real entry point, a magic
number, and a word containing the absolute entry point address.
This gets messed up with with CONFIG_THUMB2_KERNEL, because the
size of the initial padding NOPs changes.
Instead, the header can be made fully compatible by restoring it to
ARM.
In the Thumb-2 case, we can replace the initial NOPs with a
sequence which switches to Thumb and jumps to the real entry point.
As a consequence, the zImage entry point is now always ARM, so no
special magic is needed any more for the uImage rules in the
Thumb-2 case.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some instruction operand combinations are used here which are nor
permitted in Thumb-2.
In particular, most uses of pc as an operand are disallowed in
Thumb-2, and deprecated in ARM from ARMv7 onwards.
The modified code introduced by this patch should be compatible
with all architecture versions >= v3, with or without
CONFIG_THUMB2_KERNEL.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
In this specific case, we can achieve the desired alignment by
forcing a 32-bit branch instruction using the W() macro, since the
assembler location counter is already 32-bit aligned in this case.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This change limits number of GIC-originating interrupts to the
platform maximum (defined by NR_IRQS) while still initialising
all distributor registers.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Rafael Gandolfi <kaillasse91@hotmail.fr>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
RTC clock will remain at 32KHz and powered on, there is no need for it
at this moment.
Signed-off-by: Jason Chagas <jason.chagas@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
About all options present in each file are activated
in the single file.
Signed-off-by: Eric Benard <eric@eukrea.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Dependency on (CPU_S3C2416 is not selected) was defined as "!CPU_2416",
instead of "!CPU_S3C2416". Fix it.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Enable compilation of platform devices and initialization code used in
SMDK2416 board file.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP2+: PM/serial: hold console semaphore while OMAP UARTs are disabled
OMAP: UART: don't resume UARTs that are not enabled.
commit 6338a6aa7c ("ARM: 6269/1: Add 'code'
parameter for hook_fault_code()") breaks CNS3xxx build:
CC arch/arm/mach-cns3xxx/pcie.o
pcie.c: In function 'cns3xxx_pcie_init':
pcie.c:373: warning: passing argument 4 of 'hook_fault_code' makes integer from pointer without a cast
pcie.c:373: error: too few arguments to function 'hook_fault_code'
This commit fixes the small issue.
Cc: stable@kernel.org [36]
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch fixes following warning messages when CONFIG_PM selected.
In file included from arch/arm/mach-s5pv210/mach-smdkv210.c:34:
arch/arm/plat-samsung/include/plat/pm.h:104: warning: 'struct sys_device'
declared inside parameter list
arch/arm/plat-samsung/include/plat/pm.h:104: warning: its scope is only this
definition or declaration, which is probably not what you want
arch/arm/plat-samsung/include/plat/pm.h:105: warning: 'struct sys_device'
declared inside parameter list
In file included from arch/arm/mach-s5pv210/mach-smdkc110.c:31:
arch/arm/plat-samsung/include/plat/pm.h:104: warning: 'struct sys_device'
declared inside parameter list
arch/arm/plat-samsung/include/plat/pm.h:104: warning: its scope is only this
definition or declaration, which is probably not what you want
arch/arm/plat-samsung/include/plat/pm.h:105: warning: 'struct sys_device'
declared inside parameter list
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The UART3 submask should be 0x7 (SUBSRCPND[26:24]).
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
IRQ_S3C2443_UART3 is being used as the base when it should actually
be IRQ_S3C2443_RX3 on S3C2443 and S3C2416 for the UART3.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Don't rewrite clock config in UCON preconfigured by
bootloader. No need to set 10th bit in UCON because
[11:10] 2'b00 means source clock is PCLK too.
If set, console does not work if bootloader
has preconfigured [11:10] with 2'b00.
If not set, console works with any bootloader
config value (2'bxx).
More information about clock setup in UCON is available
in "S3C6410X RISC Microprocessor User's Manual,
Revision 1.20" p. 31-13 (Chapter 31.6.2
UART CONTROL REGISTER).
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Replace in s3c_gpio_cfgpull with s3c_gpio_setpull.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use IOMEM() macro to get rid of the following sparse warning:
arch/arm/mach-omap1/board-ams-delta.c:319:36: warning: incorrect type in initializer (different address spaces)
arch/arm/mach-omap1/board-ams-delta.c:319:36: expected void [noderef] <asn:2>*membase
arch/arm/mach-omap1/board-ams-delta.c:319:36: got void *<noident>
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make some variables static to get rid of the following warnings:
arch/arm/mach-omap1/mailbox.c:136:18: warning: symbol 'mbox_dsp_info' was not declared. Should it be static?
arch/arm/mach-omap1/mailbox.c:142:18: warning: symbol 'omap1_mboxes' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make some functions static to get rid of the following sparse warnings:
arch/arm/mach-omap1/mcbsp.c:177:12: warning: symbol 'omap1_mcbsp_init' was not declared. Should it be static?
arch/arm/mach-omap1/mux.c:346:22: warning: symbol 'omap1_cfg_reg' was not declared. Should it be static?
arch/arm/plat-omap/dma.c:177:5: warning: symbol 'omap_dma_in_1510_mode' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:273:12: warning: symbol 'omap1_sram_init' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing includes to get rid of the following sparse warnings:
arch/arm/mach-omap1/devices.c:225:13: warning: symbol 'omap1_camera_init' was not declared. Should it be static?
arch/arm/mach-omap1/flash.c:15:6: warning: symbol 'omap1_set_vpp' was not declared. Should it be static?
arch/arm/mach-omap1/serial.c:190:6: warning: symbol 'omap_serial_wake_trigger' was not declared. Should it be static?
arch/arm/mach-omap1/time.c:252:18: warning: symbol 'omap_timer' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The console semaphore must be held while the OMAP UART devices are
disabled, lest a console write cause an ARM abort (and a kernel crash)
when the underlying console device is inaccessible. These crashes
only occur when the console is on one of the OMAP internal serial
ports.
While this problem has been latent in the PM idle loop for some time,
the crash was not triggerable with an unmodified kernel until commit
6f251e9db1 ("OMAP: UART: omap_device
conversions, remove implicit 8520 assumptions"). After this patch, a
console write often occurs after the console UART has been disabled in
the idle loop, crashing the system. Several users have encountered
this bug:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg38396.htmlhttp://www.mail-archive.com/linux-omap@vger.kernel.org/msg36602.html
The same commit also introduced new code that disabled the UARTs
during init, in omap_serial_init_port(). The kernel will also crash
in this code when earlyconsole and extra debugging is enabled:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg36411.html
The minimal fix for the -rc series is to hold the console semaphore
while the OMAP UARTs are disabled. This is a somewhat overbroad fix,
since the console may not be located on an OMAP UART, as is the case
with the GPMC UART on Zoom3. While it is technically possible to
determine which devices the console or earlyconsole is actually
running on, it is not a trivial problem to solve, and the code to do
so is not really appropriate for the -rc series.
The right long-term fix is to ensure that no code outside of the OMAP
serial driver can disable an OMAP UART. As I understand it, code to
implement this is under development by TI.
This patch is a collaboration between Paul Walmsley <paul@pwsan.com>
and Tony Lindgren <tony@atomide.com>. Thanks to Ming Lei
<tom.leiming@gmail.com> and Pramod <pramod.gurav@ti.com> for their
feedback on earlier versions of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Pramod <pramod.gurav@ti.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Add additional check to omap_uart_resume_idle() so that only
enabled (specifically, idle-enabled) UARTs are allowed to resume.
This matches the existing check in prepare idle.
Without this patch, the system will hang if a board is
configured to register only some uarts instead of all of
them and PM is enabled.
Cc: Govindraj R. <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: clkfwk: Build fix for non-legacy CPG changes.
sh: Use GCC __builtin_prefetch() to implement prefetch().
sh: fix vsyscall compilation due to .eh_frame issue
sh: avoid to flush all cache in sys_cacheflush
sh: clkfwk: Disable init clk op for non-legacy clocks.
sh: clkfwk: Kill off now unused algo_id in set_rate op.
sh: clkfwk: Kill off unused clk_set_rate_ex().
The find_next_bit, find_first_bit, find_next_zero_bit
and find_first_zero_bit functions were not properly
clamping to the maxbit argument at the bit level. They
were instead only checking maxbit at the byte level.
To fix this, add a compare and a conditional move
instruction to the end of the common bit-within-the-
byte code used by all the functions and be sure not to
clobber the maxbit argument before it is used.
Cc: <stable@kernel.org>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: James Jones <jajones@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PLLC2 clock was utilizing the same sort of enable/disable without
regard to usecount approach that the FSIDIV clock was when being used as
a PLL pass-through. This forces the enable/disable through the clock
framework, which now prevents the clock from being ripped out or modified
underneath users that have an existing handle on it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current AP4 FSI didn't use set_rate for ak4642,
and used dummy rate when init.
And FSI driver was modified to always call set_rate.
The user which are using FSI set_rate is only AP4 now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current AP4 FSI set_rate function used bogus clock process
which didn't care enable/disable and clk->usecound.
To solve this issue, this patch also modify FSI driver to call
set_rate with enough options.
This patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current FSIDIV clock framework had bogus disable.
This patch remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (41 commits)
ALSA: hda - Identify more variants for ALC269
ALSA: hda - Fix wrong ALC269 variant check
ALSA: hda - Enable jack sense for Thinkpad Edge 11
ALSA: Revert "ALSA: hda - Fix switching between dmic and mic using the same mux on IDT/STAC"
ALSA: hda - Fixed ALC887-VD initial error
ALSA: atmel - Fix the return value in error path
ALSA: hda: Use hp-laptop quirk to enable headphones automute for Asus A52J
ALSA: snd-atmel-abdac: test wrong variable
ALSA: azt3328: period bug fix (for PA), add missing ACK on stop timer
ALSA: hda: Add Samsung R720 SSID for subwoofer pin fixup
ALSA: sound/pci/asihpi/hpioctl.c: Remove unnecessary casts of pci_get_drvdata
ALSA: sound/core/pcm_lib.c: Remove unnecessary semicolons
ALSA: sound/ppc: Use printf extension %pR for struct resource
ALSA: ac97: Apply quirk for Dell Latitude D610 binding Master and Headphone controls
ASoC: uda134x - set reg_cache_default to uda134x_reg
ASoC: Add support for MAX98089 CODEC
ASoC: davinci: fixes for multi-component
ASoC: Fix register cache setup WM8994 for multi-component
ASoC: Fix dapm_seq_compare() for multi-component
ASoC: RX1950: Fix hw_params function
...
init_mm used at kernel/sched.c:idle_task_exit() has spin_lock
(init_mm.context.id_lock) that is not initialized when spin_lock/unlock
is called at an ARM machine. Note that mm_struct.context.id_lock is
usually initialized except for the instance of init_mm at
linux/arch/arm/mm/context.c
Not initializing this spinlock incurs "BUG: pinlock bad magic"
warning when spinlock debug is enabled. We have observed such
instances when testing PM in S5PC210 machines.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adding KERN_WARNING in the middle of strings now produces those tokens
in the output, rather than accepting the level as was once the case.
Fix this in the one reported case. There might be more...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We now:
* check for a v3 controller before setting 8-bit bus width
* offer a callback for platform code to switch to 8-bit mode, which
allows non-v3 controllers to support it
* rely on mmc->caps |= MMC_CAP_8_BIT_DATA; in platform code to specify
that the board designers have indeed brought out all the pins for
8-bit to the slot.
We were previously relying only on whether the *controller* supported
8-bit, which doesn't tell us anything about the pin configuration in
the board design.
This fixes the MMC card regression reported by Maxim Levitsky here:
http://thread.gmane.org/gmane.linux.kernel.mmc/4336
by no longer assuming that 8-bit works by default.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The .stack section doesn't contain any contents, and doesn't require
initialization either. Rather than marking the output section with
'NOLOAD' but still having it exist in the object files, mark it with
%nobits which avoids the assembler marking the section with 'CONTENTS'.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 8b592783 added a Thumb-2 variant of usracc which, when it is
called with \rept=2, calls usraccoff once with an offset of 0 and
secondly with a hard-coded offset of 4 in order to avoid incrementing
the pointer again. If \inc != 4 then we will store the data to the wrong
offset from \ptr. Luckily, the only caller that passes \rept=2 to this
function is __clear_user so we haven't been actively corrupting user data.
This patch fixes usracc to pass \inc instead of #4 to usraccoff
when it is called a second time.
Cc: <stable@kernel.org>
Reported-by: Tony Thompson <tony.thompson@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current implementation of sched_clock() for the Nomadik
family is based on the clock source that will wrap around without
any compensation. Currently on the Ux500 after 1030 seconds.
Utilize cnt32_to_63 to expand the sched_clock() counter to 63
bits and introduce a keepwarm() timer to assure that sched clock
and this cnt32_to_63 is called atleast once every half period.
When I print out the actual wrap-around time, and using
a year (3600*24*365 seconds) as minumum wrap limit I get an
actual wrap-around of:
sched_clock: using 55 bits @ 8333125 Hz wrap in 416 days
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 7c63984b86 (ARM: do not define VMALLOC_END relative to PAGE_OFFSET)
changed VMALLOC_END to be an explicit value. Before this, it was
relative to PAGE_OFFSET and therefore converted to unsigned long
as PAGE_OFFSET is an unsigned long. This introduced the following
build warning. Fix this by changing the explicit defines of
VMALLOC_END to be unsigned long.
CC arch/arm/mm/init.o
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Uwe Kleine-K <u.kleine-koenig@pengutronix.dee>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This change updates the ux500 specific outer cache code to use
the new *_relaxed() I/O accessors.
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the compiler to better optimize the page table walking code
by avoiding over-complex pmd_addr_end() calculations. These
calculations prevent the compiler spotting that we'll never iterate
over the PMD table, causing it to create double nested loops where
a single loop will do.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix a MSTP assignment problem in the sh7372 clock
framework code. The USB drivers should attach to
MSTP322 not MSTP33 where IIC1 is located.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Multi-component commit f0fba2ad broke a few things which this patch should
fix. Tested on the DM355 EVM. I've been as careful as I can, but it would be
good if those with access to other Davinci boards could test.
--
The multi-component commit put the initialisation of
snd_soc_dai.[capture|playback]_dma_data into snd_soc_dai_ops.hw_params of the
McBSP, McASP & VCIF drivers (davinci-i2s.c, davinci-mcasp.c & davinci-vcif.c).
The initialisation had to be moved from the probe function in these drivers
because davinci_*_dai changed from snd_soc_dai to snd_soc_dai_driver.
Unfortunately, the DMA params pointer is needed by davinci_pcm_open (in
davinci-pcm.c) before hw_params is called. I have moved the initialisation to
a new snd_soc_dai_ops.startup function in each of these drivers. This fix
indicates that all platforms that use davinci-pcm must have been broken and
need to test with this fix.
--
The multi-component commit also changed the McBSP driver name from
"davinci-asp" to "davinci-i2s" in davinci-i2s.c without updating the board
level references to the driver name. This change is understandable, as there
is a similarly named "davinci-mcasp" driver in davinci-mcasp.c.
There is probably no 'correct' name for this driver. The DM6446 datasheet
calls it the "ASP" and describes it as a "specialised McBSP". The DM355
datasheet calls it the "ASP" and describes it as a "specialised ASP". The
DM365 datasheet calls it the "McBSP". Rather than fix this problem by
reverting to "davinci-asp", I've elected to avoid future confusion with the
"davinci-mcasp" driver by changing it to "davinci-mcbsp", which is also
consistent with the names of the functions in the driver. There are other
fixes required, so it was never going to be as simple as a revert anyway.
--
The DM365 only has one McBSP port (of the McBSP platforms, only the DM355 has
2 ports), so I've changed the the id of the platform_device from 0 to -1.
--
In davinci-evm.c, the DM6446 EVM can no longer share a snd_soc_dai_link
structure with the DM355 EVM as they use different cpu DAI names (the DM355
has 2 ports and the EVM uses the second port, but the DM6446 only has 1 port).
This also means that the 2 boards need different snd_soc_card structures.
--
The codec_name entries in davinci-evm.c didn't match the i2c ids in the board
files. I have only checked and fixed the details of the names used for the
McBSP based platforms. Someone with a McASP based platform (eg DA8xx) should
check the others.
Signed-off-by: Chris Paulson-Ellis <chris@edesix.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Removed mux: and added the __func__ macro to make debugging
easier.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The mux framework allows the change of pad configuration by drivers
when needed. Prior to this the mux framework has to be initialised
with all the mux parameters specific to the board. The mux init is
already present in the board file for SDP. Adding the mux init
for panda boards.
Signed-off-by: sricharan <r.sricharan@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Select the CBS package if SDP4430 is enabled during config.
Use the proper package (CBL or CBS) based on chip revision.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Please note that the full muxmodes are re-defined for ES2 instead
of using the subset. There are 81 differences among 204 pins.
The subset fixup will have to iterate over the whole list for each
subset entry, which can lead to an important number of iteration.
On the other hand, it will take much more memory at boot time.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Select the CBL package if SDP4430 is enabled during config.
Initialize the mux framework during the board init.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Add data for OMAP4430 generated from HW pinout & register database.
The data set is split in two partitions for both core and wkup.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Starting on OMAP4, the pin mux configuration is located in two
different partitions of the control module (CODE_PAD and WKUP_PAD).
The first one is inside the core power domain whereas the second
one is inside the wakeup.
- Add the capability to add any number of partition during board init
time depending of Soc partitioning.
- Add some init flags as well in order to avoid explicit Soc version
check inside the mux core code.
- Add a comment with mux0 mode on top of omap_mux/board/<partition>
if the current mux mode is not the default one.
Thanks to Tony Lindgren <tony@atomide.com> for the following improvements:
- Add omap_mux_get for getting the partition data so platform level
device code can use it.
- Fix the rx51 board code to use the new API.
- Do not store the partition for each mux entry. Look up the partition
for debugfs instead.
Thanks to Dan Murphy <dmurphy@ti.com> for testing on OMAP4 and reporting
a couple of bugs.
Thanks to Anand Gadiyar <gadiyar@ti.com> for testing on OMAP3 zoom and
bug report.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Murphy Dan <dmurphy@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Replace all the printk(KERN_XXX... with pr_xxx macros.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
arm: omap1: devices: need to return with a value
OMAP1: camera.h: add missing include
omap: dma: Add read-back to DMA interrupt handler to avoid spuriousinterrupts
OMAP2: Devkit8000: Fix mmc regulator failure
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: intc: Fix up build failure introduced by radix tree changes.
MAINTAINERS: update the sh git tree entry.
sh: clkfwk: fix up compiler warnings.
sh: intc: Fix up initializers for gcc 4.5.
rtc: rtc-sh - fix a memory leak
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: ap4evb: add fsib 44100Hz rate
MAINTAINERS: update the ARM SH-Mobile git tree entry.
ARM: mach-shmobile: ap4evb: Mark NOR boot loader partitions read-only.
ARM: mach-shmobile: intc-sh7372: fix interrupt number
Now that clk_set_rate_ex() is gone, there is also no way to get at rate
setting algo id, which is now also completely unused. Kill it off before
new clock ops start using it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 35bab0589b (ARM: imx: change the way
spi-imx devices are registered) contained a typo in mx25, leading to link time
failure.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Currently compilation breaks for the eukrea mbimx27 baseboard
when CONFIG_SPI_IMX is selected and CONFIG_TOUCHSCREEN_ADS7846
is not selected. Fix this by removing the ifdefs altogether.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Eric Benard <eric@eukrea.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: GIC: don't disable software generated interrupts
ARM: 6472/1: vexpress ct-ca9x4: only set twd_base if local timers are being used
ARM: arch/arm/kernel/traps.c: Convert sprintf_symbol to %pS
ARM: arch/arm/kernel/hw_breakpoint.c: Convert WARN_ON to WARN
ARM: 6462/1: EP93xx: Document DMA M2P API
ARM: 6470/1: atomic64: use generic implementation for OABI configurations
ARM: 6469/1: perf-events: squash compiler warning
ARM: 6468/1: backtrace: fix calculation of thread stack base
ARM: Fix DMA coherent allocator alignment
ARM: orion5x/kirkwood/mv78xx0: fix MPP configuration corner cases
[ARM] TS-78xxx NAND resource type should be IORESOURCE_MEM
ARM: pxa/saar: fix the building failure caused by typo
ARM: pxa/cm-x2xx: remove duplicate call to pxa27x_init_irq
ARM: pxa: fix the missing definition of IRQ_BOARD_END
ARM: mmp: fix cpuid detection on mmp2
[ARM] Kirkwood: restrict the scope of the PCIe reset workaround
[ARM] Kirkwood: fix timer initialization for LaCie boards
[ARM] Kirkwood: enhance TCLK detection
Software generated interrupts (SGI) are used for IPIs by the kernel.
While previous revisions of the GIC hardware were specified not to
implement enable bits for SGIs, more recent hardware is now permitted
to implement these bits in a per-CPU banked register.
The priority registers for the PPI and SGIs are also per-CPU banked
registers, so ensure that these are also appropriately initialized.
Reported-by: Scott Valentine <svalentine@concentris-systems.com>
Acked-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a big revert of a lot of -rc1 tidspbridge patches in order to
get the driver back into a working state. It also includes a OMAP patch
that was approved by the OMAP maintainer.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also, don't be picky about the location, which incidentally fixes the
build since MEMBLOCK_REAL_LIMIT is gone on 2.6.37.
arch/arm/plat-omap/devices.c: In function 'omap_dsp_reserve_sdram_memblock':
arch/arm/plat-omap/devices.c:287: error: 'MEMBLOCK_REAL_LIMIT'
undeclared (first use in this function)
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
In commit bde28b84, I made the assumption that CONFIG_SMP is always set
for the quad-core ct-ca9x4 platform. As it turns out, people who aren't
using the SMP goodness are confronted with a build failure.
This patch fixes this issue by ensure that twd_base is only set if
local timers are being used (and therefore SMP support is configured).
Reported-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Split the OMAP1 and OMAP2+ platform_device build and register code.
Convert the OMAP2+ variant to use omap_device.
This patch was developed in collaboration with Rajendra Nayak
<rnayak@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add hwmod structures for I2C controllers on OMAP3430.
This patch was developed in collaboration with Paul Walmsley
<paul@pwsan.com>.
OMAP3 fixes for correct IDLEST bit monitoring from
G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add hwmod structures for I2C controllers on OMAP2420/2430.
NOTE: I2C module on OMAP2420 has 16bit registers and causes imprecise
aborts if 32bits are read/written to it. Use the HWMOD_16BIT_REG flag
to notify the hmwod framework of this hard requirement so that
__raw_writew/readw is used to read /write the mdoule registers.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Get rid of the following warning:
arch/arm/mach-omap1/devices.c: In function 'omap_init_wdt':
arch/arm/mach-omap1/devices.c:298: warning: 'return' with
no value, in function returning non-void
while at that, also change:
platform_device_register();
return 0;
into:
return platform_device_register();
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes the loader and bootenv partitions read-only under MTD for the
on-board NOR flash.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add kernel-doc documentation for the EP93xx DMA memory to
peripheral/peripheral to memory API.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The old apcs-gnu ABI doesn't guarantee that double words are allocated
to registers with even alignment, causing the 64-bit exclusive memory
operations to be rejected by the assembler.
This patch requires that CONFIG_AEABI is set in order to use the native
atomic operations and falls back to the generic (spinlock) code otherwise.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
armv7_pmnc_counter_has_overflowed can return uninitialised data
if an invalid counter is specified.
This patch fixes the code to return 0 in this case, which squashes
the compiler warning from GCC 4.5.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When unwinding stack frames we must take care not to unwind
areas of memory that lie outside of the known extent of the stack.
This patch fixes an incorrect calculation of the stack base where
THREAD_SIZE is added to the stack pointer after it has already
been aligned to this value. Since the ALIGN macro performs this
addition internally, we end up overshooting the base by 8k.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
An out by one bug meant that the DMA coherent allocator was aligning
to one more bit than it should, causing it to run out of available
memory quicker. Fix this.
Reported-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Set onenand_setup to NULL instead of adding a no-op function.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
#include <media/omap1_camera.h> directive is required to
compile the dependant boards (board-ams-delta for now).
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Flush the writes to IRQSTATUS_L0 register in the DMA interrupt handler by reading the register
directly after write. This prevents the spurious DMA interrupts noted when using VDD_OPP 1
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Acked-by: Santosh Shilimkar <Santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following error:
>regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
>twl_reg twl_reg.6: can't register VMMC1, -22
>twl_reg: probe of twl_reg.6 failed with error -22
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wrong MPP configuration would cause <cpu>_mpp_conf loop infinitely
because the mpp list iterator would not be incremented.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The type was IORESOURCE_IO which is not what is expected by
plat_nand_probe(). This device has not worked since 2d098a72
("mtd: plat_nand: request memory resource before doing ioremap").
Signed-off-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
As non-PFC chips are added that may support IRQs, pass through to the
generic helper. This follows the the SH change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The updated sh clock framework has introduced a .nr_freqs element of struct
clk, which has to be initialised with the number of possible frequencies.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
