ipr_cmd_label[] isn't big enough for an eight byte string plus terminator.
Fix by shortening the string to seven bytes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
MSI has only been tested on and known to work with PCI-E based adapters. This
patch adds a field to struct ipr_chip_t to indicate which type of interrupt to
use based on what is known about the chip.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The return value from pci_enable_msi() can not always be trusted. This patch
adds code to generate an interrupt after MSI has been enabled and tests
whether or not we can receive and process it. If the tests fails, then fall
back to LSI.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Enable MSI if available/supported.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[jejb: limit ioctl to returning 20 characters to avoid overrun
on long device names and add a few more conversions]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use a newly added PCI API to issue a PCI Fundamental reset
(warm reset) to a new ipr PCI-E adapter. Typically, the
ipr adapter uses the start BIST bit in config space to reset
an adapter. Issuing start BIST on this particular adapter
results in the PCI-E logic on the card losing sync, which
causes PCI-E errors, making the card unusable. The only reset
mechanism that exists on this hardware that does not have this
problem is PCI Fundamental reset (warm reset).
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Enables multi-initiator support on ipr RAID adapters that support it.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In ipr dual adapter configurations, the ipr adapter firmware
may require an adapter reset for various reasons. The reset
is requested by the adapter firmware logging an error with
an IOASC of 0x02048000. Add support to log this error, and
reset the adapter.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Improve overall command performance by embedding the scatterlist
in the command block used by the adapter. This decreases
the overall number of DMAs required for a single command.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds support for some new PCI-E ipr adapters.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some ipr adapters may take longer than others to come operational.
This patch makes this timeout different for different adapters,
while still preserving the module parameter which can be used
to globally override the default.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since the default error log size has increased on SAS adapters,
prevent ipr from logging this additional data unless requested
to do so by the user set log level in order to prevent flooding
the logs.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds support for logging SAS fabric errors logged by
the ipr firmware.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds support to attach SATA devices to ipr SAS adapters.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add some hardware defined types for SATA. This is required
by future patches to add SATA support to ipr.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove some unused printk macros, make some more robust, and
convert some to use standard printk macros when possible.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixup a check used by the ipr driver to determine if a given
device is a SCSI disk. Due to the addition of support for
attaching SATA devices, this check needs to be more robust.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Instead of NULLing the resource entry pointer when a disk
goes away to prevent any new commands being sent to it,
set the adapter resource handle to an invalid value so
new ops getting sent to it will fail with a selection timeout
response. This patch is needed for future SATA patches.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since scsi core is always sending scatterlists now, remove
some code which was written with the bad assumption that
a small transfer would not be sent down in a scatterlist.
Without this fix, the ipr driver ends up sending garbage
data to the adapter following a reset, causing it to
fail the reset and take the adapter offline.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When kexec booting a kernel when the previous kernel did not
call ipr's shutdown method, the ipr adapter does not get
properly initialized, which can result in the ipr adapter
completing commands issued by the previous kernel. Fix ipr
to detect this scenario by reading the adapter's interrupt
mask register and the microprocessor interrupt register.
If the interrupt mask register indicates that interrupts
are enabled or the reset alert bit is set when the card is
probed, this means the card is in an unknown state and we
hard reset the card.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some new ipr adapters do not support some of the initialization
commands currently sent to it from the driver. Handle these
commands failing and continue on with the adapter initialization.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Increase device scanning limits so that all devices are found.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New ipr adapters support a new device queueing model in the
adapter firmware. The queueing model is the NACA queueing model,
but it does not mean use of NACA is required. The new model removes
some of the adapter firmware queue state that made handling QERR=0
almost impossible. The queueing model on older adapters included the
concept of a queue frozen state, which would freeze the response
queue in the adapter when a check condition occurred, requiring a
a primitive to resume the queue. The new queueing model removes this
complexity.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Handle some new types of ipr errors that can be returned by the adapter.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some newer ipr adapters are capable of returning autosense from
devices that support it. This patch adds the data structures for
the autosense buffer.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some IPR RAID adapter will automatically create single device RAID arrays
for all attached devices when the card is initialized. Setting the
RUNTIME_RESET doorbell bit will prevent this from occurring, since we
only want this behavior the first time the card is initialized and not
each time the card happens to get reset.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for handling some new errors that may be returned
by ipr adapters.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make some compile time debugging options runtime module options.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If the write buffer command that is issued to the ipr adapter
to update its microcode fails for some reason, the DMA buffer
will never get unmapped. Move the pci_map/unmap out of the
IOA reset job so that the buffer is always clearly mapped
and unmapped.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds a scsi_host sysfs attribute and module parm to enable/disable
the write cache on an ipr adapter.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds a macro in the ipr driver for logging a physical device location.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify the ipr error structures a bit by removing some duplication.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
