Turns out latest upstream U-Boot does not configure/enable pll_u which
leaves it at some default rate of 500 kHz:
root@apalis-t30:~# cat /sys/kernel/debug/clk/clk_summary | grep pll_u
pll_u 3 3 0 500000 0
Of course this won't quite work leading to the following messages:
[ 6.559593] usb 2-1: new full-speed USB device number 2 using tegra-
ehci
[ 11.759173] usb 2-1: device descriptor read/64, error -110
[ 27.119453] usb 2-1: device descriptor read/64, error -110
[ 27.389217] usb 2-1: new full-speed USB device number 3 using tegra-
ehci
[ 32.559454] usb 2-1: device descriptor read/64, error -110
[ 47.929777] usb 2-1: device descriptor read/64, error -110
[ 48.049658] usb usb2-port1: attempt power cycle
[ 48.759475] usb 2-1: new full-speed USB device number 4 using tegra-
ehci
[ 59.349457] usb 2-1: device not accepting address 4, error -110
[ 59.509449] usb 2-1: new full-speed USB device number 5 using tegra-
ehci
[ 70.069457] usb 2-1: device not accepting address 5, error -110
[ 70.079721] usb usb2-port1: unable to enumerate USB device
Fix this by actually allowing the rate also being set from within
the Linux kernel.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently VDE clock rate is determined by clock config left from
bootloader, let's not rely on it and explicitly specify the clock
rate in the CCF driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
PLL_C_OUT_1 can't produce 216 MHz defined in the init_table. Let's
set it to 240 MHz and explicitly specify HCLK rate for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Machine dies if HCLK, SCLK or EMC is disabled. Hence mark these clocks
as critical.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: <stable@vger.kernel.org> # v4.16
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has a hw bug which can cause IP blocks to lock up when ungating a
domain. The reason is that the logic responsible for resetting the memory
built-in self test mode can come up in an undefined state because its
clock is gated by a second level clock gate (SLCG). Work around this by
making sure the logic will get some clock edges by ensuring the relevant
clock is enabled and temporarily override the relevant SLCGs.
Unfortunately for some IP blocks, the control bits for overriding the
SLCGs are not in CAR, but in the IP block itself. This means we need to
map a few extra register banks in the clock code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
fixup mbist
To ensure writes to clock registers have properly propagated through the
clock control logic and state machines, we need to ensure the writes have
been posted in the registers and wait for 1us after that.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock is needed by the memory built-in self test work around.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
large change that introduces runtime PM support to the clk framework. Now we
properly call runtime PM operations on the device providing a clk when the clk
is in use. This helps on SoCs where the clks provided by a device need
something to be powered on before using the clks, like power domains or
regulators. It also helps power those things down when clks aren't in use. The
other core change is a devm API addition for clk providers so we can get rid of
a bunch of clk driver remove functions that are just doing
of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and smattering
of non-critical fixes to existing drivers. The biggest diff is support for
Mediatek MT2712 and MT7622 SoCs, but those patches really just add a bunch
of data.
By the way, we're trying something new here where we build the tree up with
topic branches. We plan to work this into our workflow so that we don't step
on each other's toes, and so the fixes branch can be merged on an as-needed
basis.
Core:
- Runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- Runtime PM support for Samsung exynos5433/exynos4412 providers
- Removal of clkdev aliases on Samsung SoCs
- Convert clk-gpio to use gpio descriptors
- Various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- Sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- Support for the second display unit clock on Renesas RZ/G1E
- Suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- New clock ids for Rockchip rk3188 and rk3368 SoCs
- Various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hC7z
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have two changes to the core framework this time around.
The first being a large change that introduces runtime PM support to
the clk framework. Now we properly call runtime PM operations on the
device providing a clk when the clk is in use. This helps on SoCs
where the clks provided by a device need something to be powered on
before using the clks, like power domains or regulators. It also helps
power those things down when clks aren't in use.
The other core change is a devm API addition for clk providers so we
can get rid of a bunch of clk driver remove functions that are just
doing of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and
smattering of non-critical fixes to existing drivers. The biggest diff
is support for Mediatek MT2712 and MT7622 SoCs, but those patches
really just add a bunch of data.
By the way, we're trying something new here where we build the tree up
with topic branches. We plan to work this into our workflow so that we
don't step on each other's toes, and so the fixes branch can be merged
on an as-needed basis.
Summary:
Core:
- runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- runtime PM support for Samsung exynos5433/exynos4412 providers
- removal of clkdev aliases on Samsung SoCs
- convert clk-gpio to use gpio descriptors
- various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- support for the second display unit clock on Renesas RZ/G1E
- suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- new clock ids for Rockchip rk3188 and rk3368 SoCs
- various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: stm32h7: fix test of clock config
clk: pxa: fix building on older compilers
clk: sunxi-ng: a83t: Fix i2c buses bits
clk: ti: dra7-atl-clock: fix child-node lookups
clk: qcom: common: fix legacy board-clock registration
clk: uniphier: fix DAPLL2 clock rate of Pro5
clk: uniphier: fix parent of miodmac clock data
clk: hi3798cv200: correct parent mux clock for 'clk_sdio0_ciu'
clk: hisilicon: Delete an error message for a failed memory allocation in hisi_register_clkgate_sep()
clk: hi3660: fix incorrect uart3 clock freqency
clk: kona-setup: Delete error messages for failed memory allocations
ARC: clk: fix spelling mistake: "configurarion" -> "configuration"
clk: cdce925: remove redundant check for non-null parent_name
clk: versatile: Improve sizeof() usage
clk: versatile: Delete error messages for failed memory allocations
clk: ux500: Improve sizeof() usage
clk: ux500: Delete error messages for failed memory allocations
clk: spear: Delete error messages for failed memory allocations
clk: ti: Delete error messages for failed memory allocations
clk: mmp: Adjust checks for NULL pointers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Below is the call trace of tegra210_init_pllu() function:
start_kernel()
-> time_init()
--> of_clk_init()
---> tegra210_clock_init()
----> tegra210_pll_init()
-----> tegra210_init_pllu()
Because the preemption is disabled in the start_kernel before calling
time_init, tegra210_init_pllu is actually in an atomic context while
it includes a readl_relaxed_poll_timeout that might sleep.
So this patch just changes this readl_relaxed_poll_timeout() to its
atomic version.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both tegra124-dfll and clk-dfll are using platform_set_drvdata
to set drvdata of the exact same pdev while they use different
pointers for the drvdata. Once the drvdata has been overwritten
by tegra124-dfll, clk-dfll will never get its td pointer as it
expects.
Since tegra124-dfll merely needs its soc pointer in its remove
function, this patch fixes the bug by removing the overwriting
in the tegra124-dfll file and letting the tegra_dfll_unregister
return an soc pointer for it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to comments in code and common sense, cclk_lp uses its
own divisor, not cclk_g's.
Fixes: b08e8c0ecc ("clk: tegra: add clock support for Tegra30")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
AHB DMA is a running on 1/2 of SCLK rate, APB DMA on 1/4. Increasing SCLK
rate results in an increased DMA transfer rate.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The APBDMA clock is defined in the common clock gates table that is used
by Tegra30+. Tegra20 can use it too, let's remove the custom definition
and use the common one.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
APBDMA represents a clock gate to the APB DMA controller, the actual
clock source for the controller is PCLK.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
AHB DMA engine presents on Tegra20/30. Add missing clock entries, so that
driver for the AHB DMA controller could be implemented.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently, the APB clock is registered with the CLK_IGNORE_UNUSED flag
to prevent the clock from being disabled if unused on boot. However,
even if it is used, it still needs to be always kept enabled so that it
doesn't get inadvertently disabled when all of its children are, and so
update the flag for the APB clock to be CLK_IS_CRITICAL.
Suggested-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These structures are only passed to the functions tegra_clk_register_pll,
tegra_clk_register_pll{e/u} or tegra_periph_clk_init during the init
phase. These functions modify the structures only during the init phase
and after that the structures are never modified. Therefore, make them
__ro_after_init.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock was previously called sor1_src and was modelled as an input
to the sor1 module clock. However, it's really an output clock that can
be fed either from the safe, the sor1_pad_clkout or the sor1 module
clocks. sor1 itself can take input from either of the display PLLs.
The same implementation for the sor1_out clock is used on Tegra186, so
this nicely lines up both SoC generations to deal with this clock in a
uniform way.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of open-coding the same pattern repeatedly, reuse the newly
introduced tegra_clk_register_periph_data() helper that will unpack
the initialization structure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is a common pattern that registers individual peripheral clocks
from an initialization table. Add a common implementation to remove the
duplication from various call sites.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Check return code in BPMP response message(s). The typical error case is
when a clock operation is attempted with an invalid clock identifier.
Also remove error print from call to clk_get_info() as the
implementation loops through the range of all possible identifiers, yet
the operation is expected to error out when the clock ID is unused.
Signed-off-by: Timo Alho <talho@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
- Added necessary delays in PLLU enable sequence during initialization
- Applied PLLU lock to all secondary gates (PLLU_48M and PLLU_60M were
missing).
Signed-off-by: Alex Frid <afrid@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Increased Tegra210 UTMIPLL power on delay to 20us (spec maximum is 15us).
Also remove a few empty lines to make it more clear the ACTIVE_DLY_COUNT
and ENABLE_DLY_COUNT fields.
Signed-off-by: Alex Frid <afrid@nvidia.com>
Reviewed-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Mayo <jmayo@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Switched Tegra210 PLLRE registration to common PLL ops instead of special
PLLRE ops used on previous Tegra chips. The latter ops do not follow
chip specific PLL frequency table, and do not apply chip specific rate
calculation method.
Removed unnecessary default rate setting that duplicates h/w reset
state, and is overwritten by clock initialization, anyway.
Signed-off-by: Alex Frid <afrid@nvidia.com>
Reviewed-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Mayo <jmayo@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Remove from Tegra210 PLLSS registration code sections that
- attempt to set PLL minimum rate (unnecessary, and dangerous if PLL
is already enabled on boot)
- apply pre-Tegra210 defaults settings
- check IDDQ setting (duplicated with Tegra210 PLLSS check defaults)
Replaced setting of reference clock with check that default oscillator
selection is not changed, and failed registration otherwise as validation
was only done with the oscillator as the reference clock.
Reordered registration, so that PLL initialization is called after
VCOmin adjustment.
Signed-off-by: Alex Frid <afrid@nvidia.com>
Reviewed-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tegra210 PLLX uses the same sequences than then PLLC instances. So there
is no need to have a special registration function and ops struct for it.
Simplify the code by changing all references to the Tegra210 PLLX
registration function to the Tegra210 PLLC registration function and
avoid duplicate functionality.
Based on work by Alex Frid <afrid@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If the PLL is on, only warn if the defaults are not yet set. Otherwise be
silent.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Timo Alho <talho@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Increase delay after PLL IDDQ release to 5us per PLL specifications.
based on work by Alex Frid <afrid@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
I2C controllers are also on the APB bus and therefor need this flag to handle
resets correctly.
Signed-off-by: Alex Frid <afrid@nvidia.com>
Reviewed-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Don't take the fractional part into account to calculate the effective
NDIV if fractional ndiv is not enabled.
Signed-off-by: Alex Frid <afrid@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Not all fields are read from the hw depending on the PLL type. Make sure
the other fields are 0 by clearing the structure beforehand to prevent
users such as the rate re-calculation code from using bogus values.
Based on work by Alex Frid <afrid@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PLLD2 is used for HDMI which does not allow Spread Spectrum clocking.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make sure the pll_ss ops are compiled even when only building for Tegra210.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Shreshtha Sahu <ssahu@nvidia.com>
Tested-by: Shreshtha Sahu <ssahu@nvidia.com>
Reviewed-by: Jon Mayo <jmayo@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PLL SS was only controlled when setting the PLL rate, not when the PLL itself
is enabled or disabled.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Mayo <jmayo@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: James Liao <jamesjj.liao@mediatek.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Commit 8dce89a1c2 ("clk: tegra: Don't warn for PLL defaults
unnecessarily") changed the tegra210_pllcx_set_defaults() function
causing the PLL to always be reset regardless of whether it is in-use.
This function was changed so that resetting of the PLL will only be
skipped if the PLL is enabled AND 'pllcx->params->defaults_set' is not
true. However, the 'pllcx->params->defaults_set' is always true and
hence, the PLL is now always reset. This causes the boot to fail on the
Tegra210 Smaug where the PLL is already enabled and in-use. Fix this by
only resetting the PLL if not in-use and only printing the warning that
the defaults are not set after we have checked the default settings.
Fixes: 8dce89a1c2 ("clk: tegra: Don't warn for PLL defaults unnecessarily")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
iqc1, iqc2, tegra_clk_pll_a_out_adsp, tegra_clk_pll_a_out0_out_adsp, adsp
and adsp neon were not modelled. dp2 wasn't modelled for Tegra210.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Given that externx can only be used as a parent for clk_out_x, it makes
sense to propagate requests to make clk_out_x easier to handle.
Signed-off-by: Alex Frid <afrid@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The recent conversion of proper const usage was only partial and didn't
include Tegra20 and Tegra30 support. Fix that up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is needed to make the JTAG debugging interface work.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
[treding@nvidia.com: add TODO comment]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This will be used by the powergating driver to ensure proper sequencer
state when the SATA domain is powergated.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has 2 special resets which don't follow the normal pattern:
DVCO and ADSP. Add them in this patch.
Changelog:
v2: add DT bindings file
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In normal operation pll_u is under hardware control and has a fixed rate
of 480MHz. Hardware will turn on pll_u on whenever any of the XUSB
powerdomains is on. From a software point of view we model this is if
pll_u is always on using a fixed rate clock. However the bootloader
might or might not have configured pll_u this way. So we will check the
current state of pll_u at boot and reconfigure it if required.
There are 3 possiblities at kernel boot:
1) pll_u is under hardware control: do nothing
2) pll_u is under hardware control and enabled: enable hardware control
3) pll_u is disabled: enable pll_u and enable hardware control
In all cases we also check if UTMIPLL is under hardware control at boot
and configure it for hardware control if that is not the case.
The same is done during SC7 resume.
Thanks to Joseph Lo <josephl@nvidia.com> for bug fixes.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For completeness, also implement this reset framework API for Tegra.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Arto Merilainen <amerilainen@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In case 2 clocks share an enable bit and one of them is enabled by a
driver and the other one is not, CCF will think it's enabled because it
will only look at the HW state. Therefore it will disable the clock and
thus also disable the other clock which was enabled. Solve this by
reading the initial state of the enable bit and incrementing the
refcount if it's set.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Export UTMIPLL IDDQ functions. These will be needed when powergating the
XUSB partition.
Signed-off-by: BH Hsieh <bhsieh@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock clocks the ADSP Cortex-A9.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a super clock type which implements both mux and divider. This is
used for aclk.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
