Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11924/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
mtd_to_nand() was recently introduced to avoid direct accesses to the
mtd->priv field. Update all MIPS specific implementations to use this
helper.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Currently CONFIG_ARCH_HAVE_CUSTOM_GPIO_H is defined for all MIPS
machines, and each machine type provides its own gpio.h. However
only a handful really implement the GPIO API, most just forward
everythings to gpiolib.
The Alchemy machine is notable as it provides a system to allow
implementing the GPIO API at the board level. But it is not used by
any board currently supported, so it can also be removed.
For most machine types we can just remove the custom gpio.h, as well
as the custom wrappers if some exists. Some of the code found in
the wrappers must be moved to the respective GPIO driver.
A few more fixes are need in some drivers as they rely on linux/gpio.h
to provides some machine specific definitions, or used asm/gpio.h
instead of linux/gpio.h for the gpio API.
Signed-off-by: Alban Bedel <albeu@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Daniel Walter <dwalter@google.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Buesch <m@bues.ch>
Cc: abdoulaye berthe <berthe.ab@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10828/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Based on the spatch
@@
expression e;
@@
- return (e);
+ return e;
with heavy hand editing because some of the changes are either whitespace
or identation only or result in excessivly long lines.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Runtime tested on Mikrotik RB532 board.
Thanks goes to Geert Uytterhoeven for the explanation of the problem.
"I'm afraid this is not gonna help. When the port is unregistered,
its type will be reset to PORT_UNKNOWN.
So before registering it again, its type must be set again the actual
serial driver, cfr. the change to of_serial.c."
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Cc: Linux MIPS Mailing List <linux-mips@linux-mips.org>
Cc: geert@linux-m68k.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7241/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/rb532/prom.o
/home/ralf/src/linux/linux-mips/arch/mips/rb532/prom.c: In function ‘prom_setup_cmdline’:
/home/ralf/src/linux/linux-mips/arch/mips/rb532/prom.c:75:22: error: variable ‘prom_envp’ set but not used [-Werror=unused-but-set-variable]
This warning exists in gcc 4.6.0 and newer. Kernels 2.6.40 and newer use
-Wunused-but-set-variable to suppress it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
These will show up as a build failure once we clean up a
misuse of module.h in the mips termios header.
Uses export.h: (EXPORT_SYMBOL)
arch/mips/cavium-octeon/setup.c
arch/mips/pmc-sierra/yosemite/setup.c
arch/mips/rb532/devices.c
arch/mips/sni/setup.c
Uses module.h: (symbol_get/put)
arch/mips/alchemy/devboards/db1200.c
Uses module.h: (print_modules)
arch/mips/kernel/traps.c
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3448/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No drivers use auto-increment NAND, so kill the NO_AUTOINCR option entirely.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Or else we get lots of variations on this:
arch/mips/pci/pci.c:330: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
scattered throughout the build.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is the MIPS portion of Joe Perches <joe@perches.com>'s
https://patchwork.linux-mips.org/patch/2172/ which seems to have been
lost in time and space.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add missing #inclusions of <linux/irq.h> to a whole bunch of files that should
really include it. Note that this can replace #inclusions of <asm/irq.h>.
This is required for the patch to sort out irqflags handling function naming to
compile on MIPS.
The problem is that these files require access to things like setup_irq() -
which isn't available by #including <linux/interrupt.h>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The MIPS-specific macro CL_SIZE is merely aliasing the macro
COMMAND_LINE_SIZE. Other architectures use the latter; also,
COMMAND_LINE_SIZE is documented in kernel-parameters.txt, so
let's use it, and remove the alias.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We should now use dev_set_drvdata to set the driver driver_data field.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/747/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit 22242681cf ("MIPS: Extend
COMMAND_LINE_SIZE"), CL_SIZE is 4096 and local array variables with this
size will cause an build failure with default CONFIG_FRAME_WARN settings.
Although current users of such array variables are all early bootstrap
code and not likely to cause real stack overflow (thread_info corruption),
it is preferable to to declare these arrays static with __initdata.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes sure that we are not going to clear
or change the interrupt status of a GPIO interrupt
superior to 13 as this is the maximum number of GPIO
interrupt source (p.232 of the RC32434 reference manual).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mikrotik's Routerboard 532 has two builtin buttons, from which one
triggers a hardware reset. The other one is accessible through GPIO
pin 1. Sadly, this pin is being multiplexed with UART0 input, so
enabling it as interrupt source (as implied by the gpio-keys driver)
is not possible unless UART0 has been turned off. The later one though
is a rather bad idea as the Routerboard is an embedded device with
only a single serial port, so it's almost always used as serial
console device.
This patch adds a driver based on INPUT_POLLDEV, which disables the
UART and reconfigures GPIO pin 1 temporarily while reading the button
state. This procedure works fine and has been tested as part of
another, unpublished driver for this device.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This kernel symbol provides a way for drivers to switch on alternate
function for a certain GPIO pin. Turning it off is done implicitly when
changing the GPIO direction, as that would be fixed when using the given
pin als alternate function.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As rb532_dev3_ctl_res is not used by any platform device, it can be dropped
when not used for holding the physical address of the device 3 controller.
Also a size of one byte should suffice when ioremapping the physical
address mentioned above, as only a single byte is being read from and
written to it.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These kernel symbols are unused. Also, since dev3 init has been moved to
devices.c, set_434_reg() breaks compiling as it uses dev3.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This code doesn't belong to gpio.c, as it's completely unrelated to
GPIO. As dev1 and dev2 init code is in devices.c, it seems to be a more
adequate place.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The data to be written is just a byte, so use writeb instead of writel.
Also, dev3.base contains the address, not the data so referencing here
is wrong.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This register just contains the address of the actual resource, so
initialisation has to be the same as cf_slot0_res and nand_slot0_res.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As the korina ethernet driver uses platform_get_drvdata() to extract the
driver specific data from the platform device, driver_data has to be
used here.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Auto-detection works just fine, so use it instead of specifying the type
manually. Also define a platform device for the uart, as suggested by
David Daney.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As the pata-rb532-cf driver calls gpio_direction_input(), the calls to
rb532_gpio_set_func() and rb532_gpio_direction_input() are not needed since
the alternate function is automatically being disabled when changing the
GPIO pin direction.
The later two calls to rb532_gpio_set_{ilevel,istat}() are implicitly being
done by the IRQ initialisation of pata-rb532-cf.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When a driver calls gpio_set_direction_{input,output}(), it obviously
doesn't want the alternate function for that pin to be active (as the
direction would not matter in that case). This patch ensures alternate
function is disabled when the direction is being changed.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Interrupt Group 4 mapps the GPIO pins enabled as interrupt sources;
add defines to make this clear when addressing them later in code.
The mapped GPIOs support triggering on either level high or low. To
achieve this, the set_type() function calls rb532_gpio_set_ilevel() for
interrupts of the above mentioned group.
As there is no way to alter the triggering characteristics of the other
interrupts, accept level triggering on status high only. (This is just a
guess; but as the system boots fine and interrupt-driven devices (e.g.
serial console) work with no implications, it seems to be right.)
To clear a GPIO mapped IRQ, the source has to be cleared (i.e., the
interrupt status bit of the corresponding GPIO pin). This is done inside
rb532_disable_irq().
After applying these changes I could undo most of my former "fixes" to
pata-rb532-cf. Particularly all interrupt handling can be done
generically via set_irq_type() as it was before.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The algorithm works unconditionally. If bitval is one, the first line is
a no op and the second line sets the bit at offset position. Vice versa,
if bitval is zero, the first line clears the bit at offset position and
the second line is a no op.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As gpiolib doesn't support pin multiplexing, it provides no way to
access the GPIOFUNC register. Also there is no support for setting
interrupt status and level. These functions provide access to them and
are needed by the CompactFlash driver.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the wrong use of GPIO register offsets
in devices.c. To avoid further problems, use gpio_get_value
to return the NAND status instead of our own expanded code.
Also define the zero offset of the alternate function register to allow
consistent access.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch sets the correct interrupt status and level
in order to get the CompactFlash adapter working.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch converts the rb532 code to use gpio library
and register its gpio chip.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch cleans up headers and regroups informations to
where they should reside. While moving, try to have a
consistant naming for defines.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are no longer using setup_serial_port. So just remove it
from the prom code.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When there is only platform device of the same type, id = -1
should be used, fix this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch replaces a raw read using volatiles
with a readl.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
