Based on a patch from Mike McElroy created against the out-of-tree e1000e
driver:
Hitting the BUG_ON in napi_enable(). Code inspection shows that this can
only be triggered by calling napi_enable() twice without an intervening
napi_disable().
I saw the following sequence of events in the stack trace:
1) We simulated a cable pull using an Extreme switch.
2) e1000_tx_timeout() was entered.
3) e1000_reset_task() was called. Saw the message from e_err() in the
console log.
4) e1000_reinit_locked was called. This function calls e1000_down() and
e1000_up(). These functions call napi_disable() and napi_enable()
respectively.
5) Then on another thread, a monitor task saw carrier was down and executed
'ip set link down' and 'ip set link up' commands.
6) Saw the '_E1000_RESETTING'warning fron the e1000_close function.
7) Either the e1000_open() executed between the e1000_down() and e1000_up()
calls in step 4 or the e1000_open() call executed after the e1000_up()
call. In either case, napi_enable() is called twice which triggers the
BUG_ON.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Mike McElroy <mike.mcelroy@stratus.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original patch submitted my Michael Wang
<wangyun@linux.vnet.ibm.com>.
Descriptors may not be write-back while checking TX hang with flag
FLAG2_DMA_BURST on.
So when we detect hang, we just flush the descriptor and detect
again for once.
-v2 change 1 to true and 0 to false and remove extra ()
CC: Michael Wang <wangyun@linux.vnet.ibm.com>
CC: Flavio Leitner <fbl@redhat.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moved netdev_completed_queue() out of while loop in function nv_tx_done_optimized().
Because this function was in while loop,
BUG_ON(count > dql->num_queued - dql->num_completed)
was hit in dql_completed().
Signed-off-by: Igor Maravic <igorm@etf.rs>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
netfilter: Remove ADVANCED dependency from NF_CONNTRACK_NETBIOS_NS
ipv4: flush route cache after change accept_local
sch_red: fix red_change
Revert "udp: remove redundant variable"
bridge: master device stuck in no-carrier state forever when in user-stp mode
ipv4: Perform peer validation on cached route lookup.
net/core: fix rollback handler in register_netdevice_notifier
sch_red: fix red_calc_qavg_from_idle_time
bonding: only use primary address for ARP
ipv4: fix lockdep splat in rt_cache_seq_show
sch_teql: fix lockdep splat
net: fec: Select the FEC driver by default for i.MX SoCs
isdn: avoid copying too long drvid
isdn: make sure strings are null terminated
netlabel: Fix build problems when IPv6 is not enabled
sctp: better integer overflow check in sctp_auth_create_key()
sctp: integer overflow in sctp_auth_create_key()
ipv6: Set mcast_hops to IPV6_DEFAULT_MCASTHOPS when -1 was given.
net: Fix corruption in /proc/*/net/dev_mcast
mac80211: fix race between the AGG SM and the Tx data path
...
After reset ipv4_devconf->data[IPV4_DEVCONF_ACCEPT_LOCAL] to 0,
we should flush route cache, or it will continue receive packets with local
source address, which should be dropped.
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Le mercredi 30 novembre 2011 à 14:36 -0800, Stephen Hemminger a écrit :
> (Almost) nobody uses RED because they can't figure it out.
> According to Wikipedia, VJ says that:
> "there are not one, but two bugs in classic RED."
RED is useful for high throughput routers, I doubt many linux machines
act as such devices.
I was considering adding Adaptative RED (Sally Floyd, Ramakrishna
Gummadi, Scott Shender), August 2001
In this version, maxp is dynamic (from 1% to 50%), and user only have to
setup min_th (target average queue size)
(max_th and wq (burst in linux RED) are automatically setup)
By the way it seems we have a small bug in red_change()
if (skb_queue_empty(&sch->q))
red_end_of_idle_period(&q->parms);
First, if queue is empty, we should call
red_start_of_idle_period(&q->parms);
Second, since we dont use anymore sch->q, but q->qdisc, the test is
meaningless.
Oh well...
[PATCH] sch_red: fix red_change()
Now RED is classful, we must check q->qdisc->q.qlen, and if queue is empty,
we start an idle period, not end it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (31 commits)
ocfs2: avoid unaligned access to dqc_bitmap
ocfs2: Use filemap_write_and_wait() instead of write_inode_now()
ocfs2: honor O_(D)SYNC flag in fallocate
ocfs2: Add a missing journal credit in ocfs2_link_credits() -v2
ocfs2: send correct UUID to cleancache initialization
ocfs2: Commit transactions in error cases -v2
ocfs2: make direntry invalid when deleting it
fs/ocfs2/dlm/dlmlock.c: free kmem_cache_zalloc'd data using kmem_cache_free
ocfs2: Avoid livelock in ocfs2_readpage()
ocfs2: serialize unaligned aio
ocfs2: Implement llseek()
ocfs2: Fix ocfs2_page_mkwrite()
ocfs2: Add comment about orphan scanning
ocfs2: Clean up messages in the fs
ocfs2/cluster: Cluster up now includes network connections too
ocfs2/cluster: Add new function o2net_fill_node_map()
ocfs2/cluster: Fix output in file elapsed_time_in_ms
ocfs2/dlm: dlmlock_remote() needs to account for remastery
ocfs2/dlm: Take inflight reference count for remotely mastered resources too
ocfs2/dlm: Cleanup dlm_wait_for_node_death() and dlm_wait_for_node_recovery()
...
The dqc_bitmap field of struct ocfs2_local_disk_chunk is 32-bit aligned,
but not 64-bit aligned. The dqc_bitmap is accessed by ocfs2_set_bit(),
ocfs2_clear_bit(), ocfs2_test_bit(), or ocfs2_find_next_zero_bit(). These
are wrapper macros for ext2_*_bit() which need to take an unsigned long
aligned address (though some architectures are able to handle unaligned
address correctly)
So some 64bit architectures may not be able to access the dqc_bitmap
correctly.
This avoids such unaligned access by using another wrapper functions for
ext2_*_bit(). The code is taken from fs/ext4/mballoc.c which also need to
handle unaligned bitmap access.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Joel Becker <jlbec@evilplan.org>
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7182/1: ARM cpu topology: fix warning
ARM: 7181/1: Restrict kprobes probing SWP instructions to ARMv5 and below
ARM: 7180/1: Change kprobes testcase with unpredictable STRD instruction
ARM: 7177/1: GIC: avoid skipping non-existent PPIs in irq_start calculation
ARM: 7176/1: cpu_pm: register GIC PM notifier only once
ARM: 7175/1: add subname parameter to mfp_set_groupg callers
ARM: 7174/1: Fix build error in kprobes test code on Thumb2 kernels
ARM: 7172/1: dma: Drop GFP_COMP for DMA memory allocations
ARM: 7171/1: unwind: add unwind directives to bitops assembly macros
ARM: 7170/2: fix compilation breakage in entry-armv.S
ARM: 7168/1: use cache type functions for arch_get_unmapped_area
ARM: perf: check that we have a platform device when reserving PMU
ARM: 7166/1: Use PMD_SHIFT instead of PGDIR_SHIFT in dma-consistent.c
ARM: 7165/2: PL330: Fix typo in _prepare_ccr()
ARM: 7163/2: PL330: Only register usable channels
ARM: 7162/1: errata: tidy up Kconfig options for PL310 errata workarounds
ARM: 7161/1: errata: no automatic store buffer drain
ARM: perf: initialise used_mask for fake PMU during validation
ARM: PMU: remove pmu_init declaration
ARM: PMU: re-export release_pmu symbol to modules
Commit 1386be55e3 ("dccp: fix
auto-loading of dccp(_probe)") fixed a bug but created a new
compiler warning:
net/dccp/probe.c: In function ‘dccpprobe_init’:
net/dccp/probe.c:166:2: warning: the omitted middle operand in ?: will always be ‘true’, suggest explicit middle operand [-Wparentheses]
try_then_request_module() is built for situations where the
"existence" test is some lookup function that returns a non-NULL
object on success, and with a reference count of some kind held.
Here we're looking for a success return of zero from the jprobe
registry.
Instead of fighting the way try_then_request_module() works, simply
open code what we want to happen in a local helper function.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 81d54ec847.
If we take the "try_again" goto, due to a checksum error,
the 'len' has already been truncated. So we won't compute
the same values as the original code did.
Reported-by: paul bilke <fsmail@conspiracy.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in user-stp mode, bridge master do not follow state of its slaves, so
after the following sequence of events it can stuck forever in no-carrier
state:
1) turn stp off
2) put all slaves down - master device will follow their state and also go in
no-carrier state
3) turn stp on with bridge-stp script returning 0 (go to the user-stp mode)
Now bridge master won't follow slaves' state and will never reach running
state.
This patch solves the problem by making user-stp and kernel-stp behavior
similar regarding master following slaves' states.
Signed-off-by: Vitalii Demianets <vitas@nppfactor.kiev.ua>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we won't notice the peer GENID change.
Reported-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc compiler is smart enough to use a single load/store if we
memcpy(dptr, sptr, 8) on x86_64, regardless of
CONFIG_CC_OPTIMIZE_FOR_SIZE
In IP header, daddr immediately follows saddr, this wont change in the
future. We only need to make sure our flowi4 (saddr,daddr) fields wont
break the rule.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also works around a bogus gcc warning generated by an
upcoming patch from Eric Dumazet that rearranges the layout
of struct flowi4.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables or updates support for the CC770 and AN82527
CAN controller on the TQM8548 and TQM8xx boards.
CC: devicetree-discuss@lists.ozlabs.org
CC: linuxppc-dev@ozlabs.org
CC: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver works with both, static platform data and device tree
bindings. It has been tested on a TQM855L board with two AN82527
CAN controllers on the local bus.
CC: Devicetree-discuss@lists.ozlabs.org
CC: linuxppc-dev@ozlabs.org
CC: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for legacy Bosch CC770 and Intel AN82527 CAN
controllers on the ISA or PC-104 bus. The I/O port or memory address
and the IRQ number must be specified via module parameters:
insmod cc770_isa.ko port=0x310,0x380 irq=7,11
for ISA devices using I/O ports or:
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11
for memory mapped ISA devices.
Indirect access via address and data port is supported as well:
insmod cc770_isa.ko port=0x310,0x380 indirect=1 irq=7,11
Furthermore, the following mode parameter can be defined:
clk: External oscillator clock frequency (default=16000000 [16 MHz])
cir: CPU interface register (default=0x40 [DSC])
bcr: Bus configuration register (default=0x40 [CBY])
cor: Clockout register (default=0x00)
Note: for clk, cir, bcr and cor, the first argument re-defines the
default for all other devices, e.g.:
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000
is equivalent to
insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000,24000000
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point the variable j is always set to 7 and the code within
the loop has to run only once anyway.
As suggested by David Miller:
"You can simply this even further since p[7] is what is used here,
and this means len is one, the inner loop therefore executes only
once, and the p[7].field value is not used (it's zero in the table)
and the write to it is completely thrown away."
Signed-off-by: Patrick Kelle <patrick.kelle81@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b00055aacd ([NET] core: add RFC2863 operstate) changed
net_device flags from unsigned short to unsigned int.
Some core functions still assume its an unsigned short.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include linux/if_ether.h to fix below build errors:
CC arch/arm/mach-kirkwood/common.o
In file included from arch/arm/mach-kirkwood/common.c:19:
include/net/dsa.h: In function 'dsa_uses_dsa_tags':
include/net/dsa.h:192: error: 'ETH_P_DSA' undeclared (first use in this function)
include/net/dsa.h:192: error: (Each undeclared identifier is reported only once
include/net/dsa.h:192: error: for each function it appears in.)
include/net/dsa.h: In function 'dsa_uses_trailer_tags':
include/net/dsa.h:197: error: 'ETH_P_TRAILER' undeclared (first use in this function)
make[1]: *** [arch/arm/mach-kirkwood/common.o] Error 1
make: *** [arch/arm/mach-kirkwood] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ERROR: "__udivdi3" [net/sched/sch_netem.ko] undefined!
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix meta data raid-repair merge problem
Btrfs: skip allocation attempt from empty cluster
Btrfs: skip block groups without enough space for a cluster
Btrfs: start search for new cluster at the beginning
Btrfs: reset cluster's max_size when creating bitmap
Btrfs: initialize new bitmaps' list
Btrfs: fix oops when calling statfs on readonly device
Btrfs: Don't error on resizing FS to same size
Btrfs: fix deadlock on metadata reservation when evicting a inode
Fix URL of btrfs-progs git repository in docs
btrfs scrub: handle -ENOMEM from init_ipath()
Commit 4a54c8c16 introduced raid-repair, killing the individual
readpage_io_failed_hook entries from inode.c and disk-io.c. Commit
4bb31e92 introduced new readahead code, adding a readpage_io_failed_hook to
disk-io.c.
The raid-repair commit had logic to disable raid-repair, if
readpage_io_failed_hook is set. Thus, the readahead commit effectively
disabled raid-repair for meta data.
This commit changes the logic to always attempt raid-repair when needed and
call the readpage_io_failed_hook in case raid-repair fails. This is much
more straight forward and should have been like that from the beginning.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Reported-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Within nested statements, the break statement terminates only the
do, for, switch, or while statement that immediately encloses it,
So replace the break with goto.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused enum cfcnfg_phy_type and the parameter to cfserl_create.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enrolling CAIF link layers are refactored.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow NULL pointer in cfpkt_extr_head in order to
skip past header data.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit a4a710c4a7 (pkt_sched: Change PSCHED_SHIFT from 10 to
6) it seems RED/GRED are broken.
red_calc_qavg_from_idle_time() computes a delay in us units, but this
delay is now 16 times bigger than real delay, so the final qavg result
smaller than expected.
Use standard kernel time services since there is no need to obfuscate
them.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netem is not in the ability to emulate channel bandwidth. Only static
delay (and optional random jitter) can be configured.
To emulate the channel rate the token bucket filter (sch_tbf) can be used. But
TBF has some major emulation flaws. The buffer (token bucket depth/rate) cannot
be 0. Also the idea behind TBF is that the credit (token in buckets) fills if
no packet is transmitted. So that there is always a "positive" credit for new
packets. In real life this behavior contradicts the law of nature where
nothing can travel faster as speed of light. E.g.: on an emulated 1000 byte/s
link a small IPv4/TCP SYN packet with ~50 byte require ~0.05 seconds - not 0
seconds.
Netem is an excellent place to implement a rate limiting feature: static
delay is already implemented, tfifo already has time information and the
user can skip TBF configuration completely.
This patch implement rate feature which can be configured via tc. e.g:
tc qdisc add dev eth0 root netem rate 10kbit
To emulate a link of 5000byte/s and add an additional static delay of 10ms:
tc qdisc add dev eth0 root netem delay 10ms rate 5KBps
Note: similar to TBF the rate extension is bounded to the kernel timing
system. Depending on the architecture timer granularity, higher rates (e.g.
10mbit/s and higher) tend to transmission bursts. Also note: further queues
living in network adaptors; see ethtool(8).
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@drr.davemloft.net>
Need not to used 'delta' flag when add single-source to interface
filter source list.
Signed-off-by: Jun Zhao <mypopydev@gmail.com>
Signed-off-by: David S. Miller <davem@drr.davemloft.net>
Need not to used 'delta' flag when add single-source to interface
filter source list.
Signed-off-by: Jun Zhao <mypopydev@gmail.com>
Signed-off-by: David S. Miller <davem@drr.davemloft.net>
Only use the primary address of the bond device
for master_ip. This will prevent changing the ARP source
address in Active-Backup mode whenever a secondry address
is added to the bond device.
Signed-off-by: Henrik Saavedra Persson <henrik.e.persson@ericsson.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@drr.davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: twl: fix twl4030 support for smps regulators
regulator: fix use after free bug
regulator: aat2870: Fix the logic of checking if no id is matched in aat2870_get_regulator
kernel/sched.c:7354:2: warning: initialization from incompatible pointer type
Align cpu_coregroup_mask prototype interface with sched_domain_mask_f typedef
use int cpu instead of unsigned int cpu
Cc: <stable@vger.kernel.org>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SWP instruction is deprecated on ARMv6 and with ARMv7 it will be
UNDEFINED when CONFIG_SWP_EMULATE is selected. In this case, probing a
SWP instruction will cause an oops when the kprobes emulation code
executes an undefined instruction.
As the SWP instruction should be rare or non-existent in kernels for
ARMv6 and later, we can simply avoid these problems by not allowing
probing of these.
Reported-by: Leif Lindholm <leif.lindholm@arm.com>
Tested-by: Leif Lindholm <leif.lindholm@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a kprobes testcase for the instruction "strd r2, [r3], r4".
This has unpredictable behaviour as it uses r3 for register writeback
addressing and also stores it to memory.
On a cortex A9, this testcase would fail because the instruction writes
the updated value of r3 to memory, whereas the kprobes emulation code
writes the original value.
Fix this by changing testcase to used r5 instead of r3.
Reported-by: Leif Lindholm <leif.lindholm@arm.com>
Tested-by: Leif Lindholm <leif.lindholm@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
