Commit 92571a1aae ("lan78xx: Connect phy early") moves the PHY
initialisation into lan78xx_probe, but lan78xx_open subsequently calls
lan78xx_reset. As well as forcing a second round of link negotiation,
this reset frequently prevents the phy interrupt from being generated
(even though the link is up), rendering the interface unusable.
Fix this issue by removing the lan78xx_reset call from lan78xx_open.
Fixes: 92571a1aae ("lan78xx: Connect phy early")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cinterion AHS8 is a 3G device with one embedded WWAN interface
using cdc_ether as a driver.
The modem is controlled via AT commands through the exposed TTYs.
AT+CGDCONT write command can be used to activate or deactivate a WWAN
connection for a PDP context defined with the same command. UE
supports one WWAN adapter.
Signed-off-by: Bassem Boubaker <bassem.boubaker@actia.fr>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan78xx_defer_event generates an error message whenever the work item
is already scheduled. lan78xx_open defers three events -
EVENT_STAT_UPDATE, EVENT_DEV_OPEN and EVENT_LINK_RESET. Being aware
of the likelihood (or certainty) of an error message, the DEV_OPEN
event is added to the set of pending events directly, relying on
the subsequent deferral of the EVENT_LINK_RESET call to schedule the
work. Take the same precaution with EVENT_STAT_UPDATE to avoid a
totally unnecessary error message.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan78xx_read_otp tries to return -EINVAL in the event of invalid OTP
content, but the value gets overwritten before it is returned and the
read goes ahead anyway. Make the read conditional as it should be
and preserve the error code.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using wicked with a lan78xx device attached to the system, we
end up with ethtool commands issued on the device before an ifup
got issued. That lead to the following crash:
Unable to handle kernel NULL pointer dereference at virtual address 0000039c
pgd = ffff800035b30000
[0000039c] *pgd=0000000000000000
Internal error: Oops: 96000004 [#1] SMP
Modules linked in: [...]
Supported: Yes
CPU: 3 PID: 638 Comm: wickedd Tainted: G E 4.12.14-0-default #1
Hardware name: raspberrypi rpi/rpi, BIOS 2018.03-rc2 02/21/2018
task: ffff800035e74180 task.stack: ffff800036718000
PC is at phy_ethtool_ksettings_get+0x20/0x98
LR is at lan78xx_get_link_ksettings+0x44/0x60 [lan78xx]
pc : [<ffff0000086f7f30>] lr : [<ffff000000dcca84>] pstate: 20000005
sp : ffff80003671bb20
x29: ffff80003671bb20 x28: ffff800035e74180
x27: ffff000008912000 x26: 000000000000001d
x25: 0000000000000124 x24: ffff000008f74d00
x23: 0000004000114809 x22: 0000000000000000
x21: ffff80003671bbd0 x20: 0000000000000000
x19: ffff80003671bbd0 x18: 000000000000040d
x17: 0000000000000001 x16: 0000000000000000
x15: 0000000000000000 x14: ffffffffffffffff
x13: 0000000000000000 x12: 0000000000000020
x11: 0101010101010101 x10: fefefefefefefeff
x9 : 7f7f7f7f7f7f7f7f x8 : fefefeff31677364
x7 : 0000000080808080 x6 : ffff80003671bc9c
x5 : ffff80003671b9f8 x4 : ffff80002c296190
x3 : 0000000000000000 x2 : 0000000000000000
x1 : ffff80003671bbd0 x0 : ffff80003671bc00
Process wickedd (pid: 638, stack limit = 0xffff800036718000)
Call trace:
Exception stack(0xffff80003671b9e0 to 0xffff80003671bb20)
b9e0: ffff80003671bc00 ffff80003671bbd0 0000000000000000 0000000000000000
ba00: ffff80002c296190 ffff80003671b9f8 ffff80003671bc9c 0000000080808080
ba20: fefefeff31677364 7f7f7f7f7f7f7f7f fefefefefefefeff 0101010101010101
ba40: 0000000000000020 0000000000000000 ffffffffffffffff 0000000000000000
ba60: 0000000000000000 0000000000000001 000000000000040d ffff80003671bbd0
ba80: 0000000000000000 ffff80003671bbd0 0000000000000000 0000004000114809
baa0: ffff000008f74d00 0000000000000124 000000000000001d ffff000008912000
bac0: ffff800035e74180 ffff80003671bb20 ffff000000dcca84 ffff80003671bb20
bae0: ffff0000086f7f30 0000000020000005 ffff80002c296000 ffff800035223900
bb00: 0000ffffffffffff 0000000000000000 ffff80003671bb20 ffff0000086f7f30
[<ffff0000086f7f30>] phy_ethtool_ksettings_get+0x20/0x98
[<ffff000000dcca84>] lan78xx_get_link_ksettings+0x44/0x60 [lan78xx]
[<ffff0000087cbc40>] ethtool_get_settings+0x68/0x210
[<ffff0000087cc0d4>] dev_ethtool+0x214/0x2180
[<ffff0000087e5008>] dev_ioctl+0x400/0x630
[<ffff00000879dd00>] sock_do_ioctl+0x70/0x88
[<ffff00000879f5f8>] sock_ioctl+0x208/0x368
[<ffff0000082cde10>] do_vfs_ioctl+0xb0/0x848
[<ffff0000082ce634>] SyS_ioctl+0x8c/0xa8
Exception stack(0xffff80003671bec0 to 0xffff80003671c000)
bec0: 0000000000000009 0000000000008946 0000fffff4e841d0 0000aa0032687465
bee0: 0000aaaafa2319d4 0000fffff4e841d4 0000000032687465 0000000032687465
bf00: 000000000000001d 7f7fff7f7f7f7f7f 72606b622e71ff4c 7f7f7f7f7f7f7f7f
bf20: 0101010101010101 0000000000000020 ffffffffffffffff 0000ffff7f510c68
bf40: 0000ffff7f6a9d18 0000ffff7f44ce30 000000000000040d 0000ffff7f6f98f0
bf60: 0000fffff4e842c0 0000000000000001 0000aaaafa2c2e00 0000ffff7f6ab000
bf80: 0000fffff4e842c0 0000ffff7f62a000 0000aaaafa2b9f20 0000aaaafa2c2e00
bfa0: 0000fffff4e84818 0000fffff4e841a0 0000ffff7f5ad0cc 0000fffff4e841a0
bfc0: 0000ffff7f44ce3c 0000000080000000 0000000000000009 000000000000001d
bfe0: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
The culprit is quite simple: The driver tries to access the phy left and right,
but only actually has a working reference to it when the device is up.
The fix thus is quite simple too: Get a reference to the phy on probe already
and keep it even when the device is going down.
With this patch applied, I can successfully run wicked on my system and bring
the interface up and down as many times as I want, without getting NULL pointer
dereferences in between.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c,
we had some overlapping changes:
1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE -->
MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE
2) In 'net-next' params->log_rq_size is renamed to be
params->log_rq_mtu_frames.
3) In 'net-next' params->hard_mtu is added.
Signed-off-by: David S. Miller <davem@davemloft.net>
Description:
Crash was reported with syzkaller pointing to lan78xx_write_reg routine.
Root-cause:
Proper cleanup of workqueues and init/setup routines was not happening
in failure conditions.
Fix:
Handled the error conditions by cleaning up the queues and init/setup
routines.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed to support the modem found in HP EliteBook 820 G3.
Signed-off-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BroadMobi BM806U is an Qualcomm MDM9225 based 3G/4G modem.
Tested hardware BM806U is mounted on D-Link DWR-921-C3 router.
The USB id is added to qmi_wwan.c to allow QMI communication with
the BM806U.
Tested on 4.14 kernel and OpenWRT.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Description:
EEE does not work with lan7800 when AutoSpeed is not set.
(This can happen when EEPROM is not populated or configured incorrectly)
Root-Cause:
When EEE is enabled, the mac config register ASD is not set
i.e. in default state, causing EEE fail.
Fix:
Set the register when eeprom is not present.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_copy_expand without __GFP_NOWARN already does a dump_stack
on OOM so these messages are redundant.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the duplicated code for asix88179_178a bind and reset methods.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The permanent address of asix88179_178a devices is read at probe time
and should not be overwritten later. Otherwise it may be overwritten
unintentionally with a configured address.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop bogus call to usb_driver_release_interface() from an error path in
the usbnet bind() callback, which is called during interface probe. At
this point the interface is not bound and usb_driver_release_interface()
returns early.
Also remove the bogus call to clear the interface data, which is owned
by the usbnet driver and would not even have been set by the time bind()
is called.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop bogus call to usb_driver_release_interface() from an error path in
the usbnet bind() callback, which is called during interface probe. At
this point the interface is not bound and usb_driver_release_interface()
returns early.
Also remove the bogus call to clear the interface data, which is owned
by the usbnet driver and would not even have been set by the time bind()
is called.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the ARRAY_SIZE macro on a couple of arrays to determine
size of the arrays. Also fix up alignment to clean up a checkpatch
warning. Improvement suggested by Coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cinterion PL8 is an LTE modem with 2 possible WWAN interfaces.
The modem is controlled via AT commands through the exposed TTYs.
AT^SWWAN write command can be used to activate or deactivate a WWAN
connection for a PDP context defined with AT+CGDCONT. UE supports
two WWAN adapter. Both WWAN adapters can be activated a the same time
Signed-off-by: Bassem Boubaker <bassem.boubaker@actia.fr>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8152 driver handles TSO packets (limited to ~16KB) quite well,
but pretends each TSO logical packet is a single packet on the wire.
There is also some error since headers are accounted once, but
error rate is small enough that we do not care.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an attempt is made to disable RX checksums, USB adapter is changed
but netdev->features is not, because smsc75xx_set_features() returns a
non zero value.
This throws errors from netdev_rx_csum_fault() :
<devname>: hw csum failure
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set rx mode before calling netif_wake_queue() when linking on to avoid
the device missing the receiving packets.
The transmission may start after calling netif_wake_queue(), and the
packets of resopnse may reach before calling rtl8152_set_rx_mode()
which let the device could receive packets. Then, the packets of
response would be missed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device could only check the checksum of TCP and UDP packets. Therefore,
for the IPv4 packets excluding TCP and UDP, the check of checksum is necessary,
even though the IP checksum is correct.
Take ICMP for example, The IP checksum may be correct, but the ICMP checksum
may be wrong.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer phydev is initialized and this value is never read, phydev
is immediately updated to a new value, hence this initialization
is redundant and can be removed
Cleans up clang warning:
drivers/net/usb/lan78xx.c:2009:21: warning: Value stored to 'phydev'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Quectel EP06 is a Cat. 6 LTE modem. It uses the same interface as
the EC20/EC25 for QMI, and requires the same "set DTR"-quirk to work.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
en_rx_am.c was deleted in 'net-next' but had a bug fixed in it in
'net'.
The esp{4,6}_offload.c conflicts were overlapping changes.
The 'out' label is removed so we just return ERR_PTR(-EINVAL)
directly.
Signed-off-by: David S. Miller <davem@davemloft.net>
That a kevent could not be scheduled is not an error.
Such handlers must be able to deal with multiple events anyway.
As the successful scheduling of a work is a debug event, make
the failure debug priority, too.
V2: coding style
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Cristian Caravena <caravena@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
r8153 on Dell TB15/16 dock corrupts rx packets.
This change is suggested by Realtek. They guess that the XHCI controller
doesn't have enough buffer, and their guesswork is correct, once the RX
aggregation gets disabled, the issue is gone.
ASMedia is currently working on a real sulotion for this issue.
Dell and ODM confirm the bcdDevice and iSerialNumber is unique for TB16.
Note that TB15 has different bcdDevice and iSerialNumber, which are not
unique values. If you still have TB15, please contact Dell to replace it
with TB16.
BugLink: https://bugs.launchpad.net/bugs/1729674
Cc: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix initialize the uninitialized tx_qlen to an appropriate value when USB
Full Speed is used.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PID 0x9625 of YUGA CLM920-NC5.
YUGA CLM920-NC5 needs to enable QMI_WWAN_QUIRK_DTR before QMI operation.
qmicli -d /dev/cdc-wdm0 -p --dms-get-revision
[/dev/cdc-wdm0] Device revision retrieved:
Revision: 'CLM920_NC5-V1 1 [Oct 23 2016 19:00:00]'
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that the dummy byte we add to avoid
ZLPs can be forwarded by the modem to the PGW/GGSN, and that
some operators will drop the connection if this happens.
In theory, QMI devices are based on CDC ECM and should as such
both support ZLPs and silently ignore the dummy byte. The latter
assumption failed. Let's test out the first.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Telit ME910 PID 0x1101.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sierra Wireless EM7565 is an Qualcomm MDM9x50 based M.2 modem.
The USB id is added to qmi_wwan.c to allow QMI communication
with the EM7565.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qmi_wwan minidriver support a 'raw-ip' mode where frames are
received without any ethernet header. This causes alignment issues
because the skbs allocated by usbnet are "IP aligned".
Fix by allowing minidrivers to disable the additional alignment
offset. This is implemented using a per-device flag, since the same
minidriver also supports 'ethernet' mode.
Fixes: 32f7adf633 ("net: qmi_wwan: support "raw IP" mode")
Reported-and-tested-by: Jay Foster <jay@systech.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quectel BG96 is an Qualcomm MDM9206 based IoT modem, supporting both
CAT-M and NB-IoT. Tested hardware is BG96 mounted on Quectel development
board (EVB). The USB id is added to qmi_wwan.c to allow QMI
communication with the BG96.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
_dev_ is being dereferenced before it is null checked, hence there
is a potential null pointer dereference.
Fix this by moving the pointer dereference after _dev_ has been null
checked.
Addresses-Coverity-ID: 1462020
Fixes: bb1b40c7cb ("usbnet: ipheth: prevent TX queue timeouts when device not ready")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to #define the license of the driver, just put it in
the MODULE_LICENSE() line directly as a text string.
This allows tools that check that the module license matches the source
code license to work properly, as there is no need to unwind the
unneeded dereference.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Johan Hovold <johan@kernel.org>
Reported-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GetNtbFormat and SetNtbFormat requests operate on 16 bit little
endian values. We get away with ignoring this most of the time, because
we only care about USB_CDC_NCM_NTB16_FORMAT which is 0x0000. This
fails for USB_CDC_NCM_NTB32_FORMAT.
Fix comparison between LE value from device and constant by converting
the constant to LE.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Fixes: 2b02c20ce0 ("cdc_ncm: Set NTB format again after altsetting switch for Huawei devices")
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: Christian Panton <christian@panton.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-By: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iOS devices require the host to be "trusted" before servicing network
packets. Establishing trust requires the user to confirm a dialog on the
iOS device.Until trust is established, the iOS device will silently discard
network packets from the host. Currently, the ipheth driver does not detect
whether an iOS device has established trust with the host, and immediately
sets up the transmit queues.
This causes the following problems:
- Kernel taint due to WARN() in netdev watchdog.
- Dmesg spam ("TX timeout").
- Disruption of user space networking activity (dhcpd, etc...) when new
interface comes up but cannot be used.
- Unnecessary host and device wakeups and USB traffic
Example dmesg output:
[ 1101.319778] NETDEV WATCHDOG: eth1 (ipheth): transmit queue 0 timed out
[ 1101.319817] ------------[ cut here ]------------
[ 1101.319828] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:316 dev_watchdog+0x20f/0x220
[ 1101.319831] Modules linked in: ipheth usbmon nvidia_drm(PO) nvidia_modeset(PO) nvidia(PO) iwlmvm mac80211 iwlwifi btusb btrtl btbcm btintel qmi_wwan bluetooth cfg80211 ecdh_generic thinkpad_acpi rfkill [last unloaded: ipheth]
[ 1101.319861] CPU: 0 PID: 0 Comm: swapper/0 Tainted: P O 4.13.12.1 #1
[ 1101.319864] Hardware name: LENOVO 20ENCTO1WW/20ENCTO1WW, BIOS N1EET62W (1.35 ) 11/10/2016
[ 1101.319867] task: ffffffff81e11500 task.stack: ffffffff81e00000
[ 1101.319873] RIP: 0010:dev_watchdog+0x20f/0x220
[ 1101.319876] RSP: 0018:ffff8810a3c03e98 EFLAGS: 00010292
[ 1101.319880] RAX: 000000000000003a RBX: 0000000000000000 RCX: 0000000000000000
[ 1101.319883] RDX: ffff8810a3c15c48 RSI: ffffffff81ccbfc2 RDI: 00000000ffffffff
[ 1101.319886] RBP: ffff880c04ebc41c R08: 0000000000000000 R09: 0000000000000379
[ 1101.319889] R10: 00000100696589d0 R11: 0000000000000378 R12: ffff880c04ebc000
[ 1101.319892] R13: 0000000000000000 R14: 0000000000000001 R15: ffff880c2865fc80
[ 1101.319896] FS: 0000000000000000(0000) GS:ffff8810a3c00000(0000) knlGS:0000000000000000
[ 1101.319899] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1101.319902] CR2: 00007f3ff24ac000 CR3: 0000000001e0a000 CR4: 00000000003406f0
[ 1101.319905] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1101.319908] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 1101.319910] Call Trace:
[ 1101.319914] <IRQ>
[ 1101.319921] ? dev_graft_qdisc+0x70/0x70
[ 1101.319928] ? dev_graft_qdisc+0x70/0x70
[ 1101.319934] ? call_timer_fn+0x2e/0x170
[ 1101.319939] ? dev_graft_qdisc+0x70/0x70
[ 1101.319944] ? run_timer_softirq+0x1ea/0x440
[ 1101.319951] ? timerqueue_add+0x54/0x80
[ 1101.319956] ? enqueue_hrtimer+0x38/0xa0
[ 1101.319963] ? __do_softirq+0xed/0x2e7
[ 1101.319970] ? irq_exit+0xb4/0xc0
[ 1101.319976] ? smp_apic_timer_interrupt+0x39/0x50
[ 1101.319981] ? apic_timer_interrupt+0x8c/0xa0
[ 1101.319983] </IRQ>
[ 1101.319992] ? cpuidle_enter_state+0xfa/0x2a0
[ 1101.319999] ? do_idle+0x1a3/0x1f0
[ 1101.320004] ? cpu_startup_entry+0x5f/0x70
[ 1101.320011] ? start_kernel+0x444/0x44c
[ 1101.320017] ? early_idt_handler_array+0x120/0x120
[ 1101.320023] ? x86_64_start_kernel+0x145/0x154
[ 1101.320028] ? secondary_startup_64+0x9f/0x9f
[ 1101.320033] Code: 20 04 00 00 eb 9f 4c 89 e7 c6 05 59 44 71 00 01 e8 a7 df fd ff 89 d9 4c 89 e6 48 c7 c7 70 b7 cd 81 48 89 c2 31 c0 e8 97 64 90 ff <0f> ff eb bf 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00
[ 1101.320103] ---[ end trace 0cc4d251e2b57080 ]---
[ 1101.320110] ipheth 1-5:4.2: ipheth_tx_timeout: TX timeout
The last message "TX timeout" is repeated every 5 seconds until trust is
established or the device is disconnected, filling up dmesg.
The proposed patch eliminates the problem by, upon connection, keeping the
TX queue and carrier disabled until a packet is first received from the iOS
device. This is reflected by the confirmed_pairing variable in the device
structure. Only after at least one packet has been received from the iOS
device, the transmit queue and carrier are brought up during the periodic
device poll in ipheth_carrier_set. Because the iOS device will always send
a packet immediately upon trust being established, this should not delay
the interface becoming useable. To prevent failed UBRs in
ipheth_rcvbulk_callback from perpetually re-enabling the queue if it was
disabled, a new check is added so only successful transfers re-enable the
queue, whereas failed transfers only trigger an immediate poll.
This has the added benefit of removing the periodic control requests to the
iOS device until trust has been established and thus should reduce wakeup
events on both the host and the iOS device.
Signed-off-by: Alexander Kappner <agk@godking.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple cases of overlapping changes in the packet scheduler.
Must easier to resolve this time.
Which probably means that I screwed it up somehow.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit baedf68a06.
There is an updated version of this fix which covers
the problem more thoroughly.
Signed-off-by: David S. Miller <davem@davemloft.net>
