In the final versions of the Porter board (called "PORTER_C") Renesas
decided to get rid of the Maxim Integrated MAX3355 OTG chip and didn't
add any other provision to differ the host/gadget mode, so we'll have to
remove no longer valid "renesas,enable-gpio" property from the HS-USB
device node. Hopefully, the earlier revisions of the board were never
seen in the wild...
Fixes: c794f6a09a ("ARM: shmobile: porter: add HS-USB DT support")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When finishing the Porter sound support patch, I managed to call the JP3
jumper SW3 in the comment. Fix this along with (also miscalled) jumper
positions...
Fixes: 493b4da7c1 ("ARM: dts: porter: add sound support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Porter board dependent part of the R8A7791 sound device node.
Add device node for Asahi Kasei AK4642 stereo codec to the I2C2 bus.
Add the "simple-audio-card" device node to interconnect the SoC sound
device and the codec.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Porter board dependent part of the DU device node.
Add the device node for Analog Devices ADV7511W HDMI transmitter to I2C2
bus and the HDMI connector. Add the necessary subnodes to interconnect DU
and HDMI devices.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit e488ca9f8d ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commits 5cfdedb7b9 ("mtd: ofpart: move ofpart partitions to a
dedicated dt node") and fe2585e9c2 ("doc: dt: mtd: support partitions
in a special 'partitions' subnode"), having partitions as direct subnodes
of an mtd device is discouraged. Hence move the SPI FLASH partitions to a
"partitions" subnode.
Based on similar work for the koelsch board by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Porter board dependent part of the CAN0 device node.
This patch is analogous to the commit 457acc4a6c ("ARM: shmobile:
henninger: add CAN0 DT support") as there are no differences between the
boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable HS-USB device for the Porter board, defining the GPIO that the
driver should check when probing (which is the ID output from MAX3355
OTG chip).
Note that there will be pinctrl-related error messages if both internal
PCI and HS-USB drivers are enabled but they should be just ignored.
This patch is analogous to the commit 6f4f7156e0 ("ARM: shmobile:
henninger: enable HS-USB") as there are no differences between the
boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached
to them and also enable USB PHY device for the Porter board. We have to
enable everything in one patch since EHCI/OHCI devices are already linked
to the USB PHY device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the PCIe controller and clock for the Porter board.
This patch is analogous to the commit 485f3ce67c ("ARM: shmobile:
henninger: Enable PCIe Controller & PCIe bus clock") as there are no
differences between the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Porter board dependent part of the QSPI device node.
Add device nodes for Spansion S25FL512S SPI flash and the MTD partitions
on it.
This patch is mostly analogous to the commit f59838d448 ("ARM:
shmobile: henninger: add QSPI DT support") as there are no differences
between the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Porter board dependent part of the VIN0 device node.
Add the device node for Analog Devices ADV7180 video decoder to I2C2 bus.
Add the necessary subnodes to interconnect VIN0 and ADV7180 devices.
This patch is analogous to the commit 8d62f4f753 ("ARM: shmobile:
henninger: add VIN0/ADV7180 DT support") as there are no differences
between the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Porter board dependent part of the I2C2 device node.
This patch is analogous to the commit 29a647c396 ("ARM: shmobile:
henninger: add I2C2 DT support") as there are no differences between
the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable SATA0 device for the Porter board.
This patch is analogous to the commit 5a62ec5700 ("ARM: shmobile:
henninger: enable SATA0") as there are no differences between the boards
in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Porter board dependent part of the SDHI0/2 device nodes along
with the necessary voltage regulators (note that the Vcc regulators are
dummy -- they are required but don't actually exist on the board). Also,
GPIOs have to be used for the CD and WP signals due to the SDHI driver
constraints...
This patch is analogous to the commit 1299df03d7 ("ARM: shmobile:
henninger: add SDHI0/2 DT support") as there are no differences between
those boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Porter board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.
This patch is analogous to the commit 26b0d2cf73 ("ARM: shmobile:
henninger: add Ether DT support") as there are no differences between
those boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7791 SoC based Porter low cost board
(which is a slightly modified version of the Henninger board).
SCIF0 serial port support is included, so that the serial console can work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
