This reverts commit 200e0d99 ("USB: storage: optimize to match the
Huawei USB storage devices and support new switch command" and the
followup bugfix commit cd060956 ("USB: storage: properly handle
the endian issues of idProduct").
The commit effectively added a large number of Huawei devices to
the deprecated usb-storage mode switching logic. Many of these
devices have been in use and supported by the userspace
usb_modeswitch utility for years. Forcing the switching inside
the kernel causes a number of regressions as a result of ignoring
existing onfigurations, and also completely takes away the ability
to configure mode switching per device/system/user.
Known regressions caused by this:
- Some of the devices support multiple modes, using different
switching commands. There are existing configurations taking
advantage of this.
- There is a real use case for disabling mode switching and
instead mounting the exposed storage device. This becomes
impossible with switching logic inside the usb-storage driver.
- At least on device fail as a result of the usb-storage switching
command, becoming completely unswitchable. This is possibly a
firmware bug, but still a regression because the device work as
expected using usb_modeswitch defaults.
In-kernel mode switching was deprecated years ago with the
development of the more user friendly userspace alternatives. The
existing list of devices in usb-storage was only kept to prevent
breaking already working systems. The long term plan is to remove
the list, not to add to it. Ref:
http://permalink.gmane.org/gmane.linux.usb.general/28543
Cc: <fangxiaozhi@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current entry in unusual_cypress.h for the Super TOP SATA bridge devices
seems to be causing corruption on newer revisions of this device. This has
been reported in Arch Linux and Fedora. The original patch was tested on
devices with bcdDevice of 1.60, whereas the newer devices report bcdDevice
as 2.20. Limit the UNUSUAL_DEV entry to devices less than 2.20.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=909591
The Arch Forum post on this is here:
https://bbs.archlinux.org/viewtopic.php?id=152011
Reported-by: Carsten S. <carsteniq@yahoo.com>
Tested-by: Carsten S. <carsteniq@yahoo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. The idProduct is little endian, so make sure its value to be
compatible with the current CPU. Make no break on big endian processors.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pulls in a bunch of fixes that are in Linus's tree because we need them
here for testing and development.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Optimize the match rules with new macro for Huawei USB storage devices,
to avoid to load USB storage driver for the modem interface
with Huawei devices.
2. Add to support new switch command for new Huawei USB dongles.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Define a new macro for USB storage match rules:
matching with Vendor ID and interface descriptors.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
256 luns is what the sam-4 address method 0 can handle and what
the qemu uas emulation supports. So pick that for now.
[ v2: unlike the other two max_* fields max_channel isn't max+1 ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets scsi_host->max_id as 1 if the device's quirk
flag of US_FL_SCM_MULT_TARG isn't set, because there are only 6
mass storage devices marked as mutiple targets from unusual_devs.h.
This patch is a small optimization about scanning targets, and
avoid scanning other 7 non-existed targets for single target
device.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new function to unlink and abort requests from the work
list, call it on bus reset and disconnect where we kill all
in-flight urbs. Also reorder calls in disconnect to first
cancel transfers, then remove the scsi hba.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two changes. First we check whenever the request is linked in the work
list and if so take it out. Second check whenever the command is
actually in flight before asking the device to cancel it via task
management, and in case it isn't just zap the data urbs and finish it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep track whenever the request is linked into the work list or not.
Needed for request abort.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uas_unlink_data_urbs uses this to make sure the the scsi command is
not released while looking at it. This will be needed when we start
calling uas_unlink_data_urbs in the request cancel code paths.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add uas_unlink_data_urbs function to cancel in-flight data urbs.
Moves existing code into a separate function.
[ v2: also drop the locking, just call usb_unlink_urb no matter what,
which is safe because the usb core guarantees the completion
callback is called only once ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
Here's the big set of USB patches for 3.8-rc1.
Lots of USB host driver cleanups in here, and a bit of a reorg of the
EHCI driver to make it easier for the different EHCI platform drivers to
all work together nicer, which was a reduction in overall code. We also
deleted some unused firmware files, and got rid of the very old
file_storage usb gadget driver that had been broken for a long time.
This means we ended up removing way more code than added, always a nice
thing to see:
310 files changed, 3028 insertions(+), 10754 deletions(-)
Other than that, the usual set of new device ids, driver fixes, gadget
driver and controller updates and the like.
All of these have been in the linux-next tree for a number of weeks.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHhIYACgkQMUfUDdst+yk9gACgsZYgMtbrqdbhbjbYkfO7nYkB
iegAoIvj3qwe33TbZ8OJnIkaWcMiT8CW
=u6Bf
-----END PGP SIGNATURE-----
Merge tag 'usb-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big set of USB patches for 3.8-rc1.
Lots of USB host driver cleanups in here, and a bit of a reorg of the
EHCI driver to make it easier for the different EHCI platform drivers
to all work together nicer, which was a reduction in overall code. We
also deleted some unused firmware files, and got rid of the very old
file_storage usb gadget driver that had been broken for a long time.
This means we ended up removing way more code than added, always a
nice thing to see:
310 files changed, 3028 insertions(+), 10754 deletions(-)
Other than that, the usual set of new device ids, driver fixes, gadget
driver and controller updates and the like.
All of these have been in the linux-next tree for a number of weeks.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (228 commits)
USB: mark uas driver as BROKEN
xhci: Add Lynx Point LP to list of Intel switchable hosts
uwb: fix uwb_dev_unlock() missed at an error path in uwb_rc_cmd_async()
USB: ftdi_sio: Add support for Newport AGILIS motor drivers
MAINTAINERS: remove drivers/block/ub.c
USB: chipidea: fix use after free bug
ezusb: add dependency to USB
usb: ftdi_sio: fixup BeagleBone A5+ quirk
USB: cp210x: add Virtenio Preon32 device id
usb: storage: remove redundant memset() in usb_probe_stor1()
USB: option: blacklist network interface on Huawei E173
USB: OHCI: workaround for hardware bug: retired TDs not added to the Done Queue
USB: add new zte 3g-dongle's pid to option.c
USB: opticon: switch to generic read implementation
USB: opticon: refactor reab-urb processing
USB: opticon: use usb-serial bulk-in urb
USB: opticon: increase bulk-in size
USB: opticon: use port as urb context
USB: opticon: pass port to get_serial_info
USB: opticon: make private data port specific
...
As reported https://bugzilla.kernel.org/show_bug.cgi?id=51031, the UAS
driver causes problems and has been asked to be not built into any of
the major distributions. To prevent users from running into problems
with it, and for distros that were not notified, just mark the whole
thing as broken.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
scsi_host_alloc() will zero our private data, no need to memset it.
Signed-off-by: Yan Hong <clouds.yan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"Whether" is misspelled in various comments across the tree; this
fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Implement support for WRITE SAME(10) and WRITE SAME(16) in the SCSI disk
driver.
- We set the default maximum to 0xFFFF because there are several
devices out there that only support two-byte block counts even with
WRITE SAME(16). We only enable transfers bigger than 0xFFFF if the
device explicitly reports MAXIMUM WRITE SAME LENGTH in the BLOCK
LIMITS VPD.
- max_write_same_blocks can be overriden per-device basis in sysfs.
- The UNMAP discovery heuristics remain unchanged but the discard
limits are tweaked to match the "real" WRITE SAME commands.
- In the error handling logic we now distinguish between WRITE SAME
with and without UNMAP set.
The discovery process heuristics are:
- If the device reports a SCSI level of SPC-3 or greater we'll issue
READ SUPPORTED OPERATION CODES to find out whether WRITE SAME(16) is
supported. If that's the case we will use it.
- If the device supports the block limits VPD and reports a MAXIMUM
WRITE SAME LENGTH bigger than 0xFFFF we will use WRITE SAME(16).
- Otherwise we will use WRITE SAME(10) unless the target LBA is beyond
0xFFFFFFFF or the block count exceeds 0xFFFF.
- no_write_same is set for ATA, FireWire and USB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The REPORT SUPPORTED OPERATION CODES command can be used to query
whether a given opcode is supported by a device. Add a helper function
that allows us to look up commands.
We only issue RSOC if the device reports compliance with SPC-3 or
later. But to err on the side of caution we disable the command for ATA,
FireWire and USB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When rts51x_read_status() returns USB_STOR_TRANSPORT_ERROR,
an error happens. This patch fixes build warning as below:
drivers/usb/storage/realtek_cr.c: In function 'init_realtek_cr':
drivers/usb/storage/realtek_cr.c:476:33: warning: 'buf[15]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[15]' was declared here
drivers/usb/storage/realtek_cr.c:475:33: warning: 'buf[14]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[14]' was declared here
drivers/usb/storage/realtek_cr.c:474:50: warning: 'buf[13]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[13]' was declared here
drivers/usb/storage/realtek_cr.c:472:30: warning: 'buf[12]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[12]' was declared here
drivers/usb/storage/realtek_cr.c:471:31: warning: 'buf[11]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[11]' was declared here
drivers/usb/storage/realtek_cr.c:470:31: warning: 'buf[10]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[10]' was declared here
drivers/usb/storage/realtek_cr.c:469:30: warning: 'buf[9]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[9]' was declared here
drivers/usb/storage/realtek_cr.c:468:27: warning: 'buf[8]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[8]' was declared here
drivers/usb/storage/realtek_cr.c:468:43: warning: 'buf[7]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[7]' was declared here
drivers/usb/storage/realtek_cr.c:467:30: warning: 'buf[6]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[6]' was declared here
drivers/usb/storage/realtek_cr.c:466:30: warning: 'buf[5]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[5]' was declared here
drivers/usb/storage/realtek_cr.c:465:28: warning: 'buf[4]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[4]' was declared here
drivers/usb/storage/realtek_cr.c:464:24: warning: 'buf[3]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[3]' was declared here
drivers/usb/storage/realtek_cr.c:464:40: warning: 'buf[2]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[2]' was declared here
drivers/usb/storage/realtek_cr.c:463:24: warning: 'buf[1]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[1]' was declared here
drivers/usb/storage/realtek_cr.c:463:40: warning: 'buf[0]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[0]' was declared here
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streamline control flow so it is easier for gcc to follow which paths
can be taken and which can't.
Fixes "warning: 'cmdinfo' may be used uninitialized in this function"
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly report aborted commands.
Also don't access cmdinfo after kicking task management,
it may not be valid any more once it returns.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocate one tag for task management functions and
use it properly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to call scsi_get_host_dev(sh) but we never use the return
nor do we have any reason to check it.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "Low Performance USB Block driver" has been removed which a user of
libusual. Now we have only the usb-storage driver as the only driver in
tree. This makes libusual needless.
This patch removes libusal, fixes up all users. The usual-table is now
linked into usb-storage.
usb_usual.h remains in public include directory because some staging
users seem to need it.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the attribute avoid_reset_quirk is work for all devices including
those devices that can't morph, convert USB_QUIRK_RESET_MORPHS to
USB_QUIRK_RESET.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update information of Seagate Portable HDD and WD My Passport HDD in
quirk list.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for write cache quirk on usb hdd. scsi driver will be set to wce
by detecting write cache quirk in quirk list when plugging usb hdd.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add task management support, wind up in abort and device reset error
handlers. Cancel all in-flight urbs in bus reset handler.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use separate anchors for data and sense urbs, which
I think will be useful when implementing error handling.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(1) Handle data pipe errors: When the data urb failed we
didn't transfer anything, update scsi_cmnd accordingly.
(2) Cancel data transfers when we got back an error on the
status pipe.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set state bits after submitting data urbs & command urbs, so we know
what is in flight. Clear data bits when the data urb is finished, clear
command bit when we see the status urb for the command. Finish the scsi
command after running both status and data completion handlers for the
command.
Add a cmd status logging function for debugging purposes. Hook it into
the error handler, so we see in the log what status a command is in
which the scsi layer wants cancel.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop reusing sense urbs, just allocate a fresh one each time and free it
when done.
Stop storing a sense urb pointer in the scsi request, all you can do
with it is misusing. For example requeuing the sense urb, then f*ck it
up by picking the wrong one in case tagged requests don't finish in the
same order you've submitted them. Also note that (not-yet supported)
task management ops don't have a scsi request in the first place.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ceb3f91fd5.
IMO the real bug is assigning status urbs to scsi requests. First there
is no such link in the non-stream case. Also there isn't nessesarely a
scsi request in the first place, for example when submitting task
management requests.
This patch just papers over the real bug and introduces different status
urb handling in the stream/non-stream case for no good reason.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e4d8318a85.
This patch makes uas.c call usb_unlink_urb on data urbs. The data urbs
get freed in the completion callback. This is illegal according to the
usb_unlink_urb documentation.
This patch also makes the code expect the data completion callback
being called before the status completion callback. This isn't
guaranteed to be the case, even though the actual data transfer should
be finished by the time the status is received.
Background: The ehci irq handler for example only know that there are
finished transfers, it then has go check the QHs & TDs to see which
transfers did actually finish. It has no way to figure in which order
the transfers did complete. The xhci driver can call the callbacks in
completion order thanks to the event queue. This does nicely explain
why the driver is solid on a (usb2) xhci port whereas it goes crazy on
ehci in my testing.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1560) reverts commit
afff07e61a (usb-storage: Add 090c:1000
to unusal-devs). It is no longer needed, because usb-storage now
tells the sd driver to try READ CAPACITY(10) before READ CAPACITY(16)
for every USB mass-storage device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several bug reports have been received recently for USB mass-storage
devices that don't handle READ CAPACITY(16) commands properly. They
report bogus sizes, in some cases becoming unusable as a result.
The bugs were triggered by commit
09b6b51b0b (SCSI & usb-storage: add
flags for VPD pages and REPORT LUNS), which caused usb-storage to stop
overriding the SCSI level reported by devices. By default, the sd
driver will try READ CAPACITY(16) first for any device whose level is
above SCSI_SPC_2.
It seems likely that any device large enough to require the use of
READ CAPACITY(16) (i.e., 2 TB or more) would be able to handle READ
CAPACITY(10) commands properly. Indeed, I don't know of any devices
that don't handle READ CAPACITY(10) properly.
Therefore this patch (as1559) adds a new flag telling the sd driver
to try READ CAPACITY(10) before READ CAPACITY(16), and sets this flag
for every USB mass-storage device. If a device really is larger than
2 TB, sd will fall back to READ CAPACITY(16) just as it used to.
This fixes Bugzilla #43391.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This lets us catch the USB fixes that went into 3.5-rc3 into this branch,
as we want them here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device gives a bogus answer to get_capacity(16):
[ 8628.278614] scsi 8:0:0:0: Direct-Access USB 2.0 USB Flash Drive 1100 PQ: 0 ANSI: 4
[ 8628.279452] sd 8:0:0:0: Attached scsi generic sg4 type 0
[ 8628.280338] sd 8:0:0:0: [sdd] 35747322042253313 512-byte logical blocks: (18.3 EB/15.8 EiB)
So set the quirk flag to avoid using get_capacity(16) with it:
[11731.386014] usb-storage 2-1.6:1.0: Quirks match for vid 090c pid 1000: 80000
[11731.386075] scsi9 : usb-storage 2-1.6:1.0
[11731.386172] usbcore: registered new interface driver usb-storage
[11731.386175] USB Mass Storage support registered.
[11732.387394] scsi 9:0:0:0: Direct-Access USB 2.0 USB Flash Drive 1100 PQ: 0 ANSI: 4
[11732.388462] sd 9:0:0:0: Attached scsi generic sg3 type 0
[11732.389432] sd 9:0:0:0: [sdc] 7975296 512-byte logical blocks: (4.08 GB/3.80 GiB)
Which makes the capacity look a lot more sane :)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Simon Raffeiner <sturmflut@lieberbiber.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
