With devm_ APIs regmap_exit() not needed, so remove regmap_exit().
Signed-off-by: Vishwas A Deshpande <vishwas.a.deshpande@ti.com>
Signed-off-by: M R Swami Reddy <mr.swami.reddy@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: Support TI Isabelle Audio driver
The Isabelle Audio IC is a complete low power high fidelity CODEC with integrated
ADCs, DACs, decimation and interpolation filters, PLL, and power providers. This
device supports 2 analog and 2 digital microphone channels, a mono earpiece driver,
stereo class G headphone drivers with ultra low power and best SNR in the industry,
stereo Class D speaker drivers, and 2 high performance Line drivers.
The below patch is a basic driver code for TI Isabelle audio codec. The
functionalities like headset detection, etc., will be included incrementally
in the up-coming patches.
Signed-off-by: Vishwas A Deshpande <vishwas.a.deshpande@ti.com>
Signed-off-by: M R Swami Reddy <mr.swami.reddy@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
version.h header file is no longer required.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
version.h header file is no longer needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Control type added for cases where a specific range of values
within a register are required for control.
Added convenience macros:
SOC_SINGLE_RANGE
SOC_SINGLE_RANGE_TLV
Added accessor implementations:
snd_soc_info_volsw_range
snd_soc_put_volsw_range
snd_soc_get_volsw_range
Signed-off-by: Michal Hajduk <Michal.Hajduk@diasemi.com>
Signed-off-by: Adam Thomson <Adam.Thomson@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Prior to this patch, the CPU side of a DAI link was specified using a
single name. Often, this was the result of calling dev_name() on the
device providing the DAI, but in the case of a CPU DAI driver that
provided multiple DAIs, it needed to mix together both the device name
and some device-relative name, in order to form a single globally unique
name.
However, the CODEC side of the DAI link was specified using separate
fields for device (name or OF node) and device-relative DAI name.
This patch allows the CPU side of a DAI link to be specified in the same
way as the CODEC side, separating concepts of device and device-relative
DAI name.
I believe this will be important in multi-codec and/or dynamic PCM
scenarios, where a single CPU driver provides multiple DAIs, while also
booting using device tree, with accompanying desire not to hard-code the
CPU side device's name into the original .cpu_dai_name field.
Ideally, both the CPU DAI and CODEC DAI loops in soc_bind_dai_link()
would now be identical. However, two things prevent that at present:
1) The need to save rtd->codec for the CODEC side, which means we have
to search for the CODEC explicitly, and not just the CODEC side DAI.
2) Since we know the CODEC side DAI is part of a codec, and not just
a standalone DAI, it's slightly more efficient to convert .codec_name/
.codec_of_node into a codec first, and then compare each DAI's .codec
field, since this avoids strcmp() on each DAI's CODEC's name within
the loop.
However, the two loops are essentially semantically equivalent.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Less error prone and one less line of code in drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
ALSA mixers cannot classify this "Class-D Amplifier Gain" speaker output
gain control as a playback control. Fix this by changing the name as
"Class-D Playback Volume".
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
PIO handler is not good performance, but works on all platform.
So, switch to PIO handler if DMA handler was invalid case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch used dmaengine helper functions instead of using hand setting.
And reduced local variables
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add platform-driver handling all DMA-activities.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds a supply-widget variant for connection to the clock-framework.
This widget-type corresponds to the variant for regulators.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds a function getting the stream-name as a string for
a specific stream.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In kernel 3.6, Seaboard will only be supported when booting using device
tree; the board files are being removed. Hence, remove the non-DT support
for Seaboard and derivatives Kaen and Aebl from the audio driver.
Harmony is the only remaining board supported by this driver when not
using DT. This support is currently scheduled for removal in 3.7.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
By the time any widget callbacks could be called, if the GPIO ID they
will manipulate is valid, it must have already been requested, or the
card would have failed to probe or initialize. So, testing for GPIO
validity is equivalent to testing whether the GPIO was successfully
requested at this point in the code. Making this change will allow later
patches to remove the gpio_requested variable.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The headphone jack GPIOs are added/initialized in the DAI link's init()
method, and hence in theory may not always have been added before remove()
is called in some unusual cases. In order to prevent calling
snd_soc_jack_free_gpios() if snd_soc_jack_add_gpios() had not been, the
code kept track of the initialization state to avoid the free call when
necessary.
However, it appears that snd_soc_jack_free_gpios() is robust in the face
of being called without snd_soc_jack_add_gpios() first succeeding, so
there is little point manually tracking this information. Hence, remove
the tracking code. All other machine drivers already operate this way.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that deferred probe exists, we can parse device tree and request
GPIOs from probe(), rather than deferring this to the DAI link's init().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The headphone jack GPIOs are added/initialized in the DAI link's init()
method, and hence in theory may not always have been added before remove()
is called in some unusual cases. In order to prevent calling
snd_soc_jack_free_gpios() if snd_soc_jack_add_gpios() had not been, the
code kept track of the initialization state to avoid the free call when
necessary.
However, it appears that snd_soc_jack_free_gpios() is robust in the face
of being called without snd_soc_jack_add_gpios() first succeeding, so
there is little point manually tracking this information. Hence, remove
the tracking code. Almost all other machine drivers already operate this
way.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
By using this function, the driver no longer needs to explicitly free
the GPIOs. Hence, we can also remove the flags we use to track whether
we allocated these GPIOs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that deferred probe exists, we can parse device tree and request
GPIOs from probe(), rather than deferring this to the DAI link's init().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows the GPIOs to be available as soon as the I2C device has
probed, which in turn enables machine drivers to request the GPIOs in
their probe(), rather than deferring this to their ASoC machine init
function, i.e. after the whole sound card has been constructed, and
hence the WM8903 codec is available.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
and provide a simple reserve/release mechanism for userspace tools to
access thin provisioning metadata while the pool is in use.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wCpY
-----END PGP SIGNATURE-----
Merge tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper updates from Alasdair G Kergon:
"Improve multipath's retrying mechanism in some defined circumstances
and provide a simple reserve/release mechanism for userspace tools to
access thin provisioning metadata while the pool is in use."
* tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm thin: provide userspace access to pool metadata
dm thin: use slab mempools
dm mpath: allow ioctls to trigger pg init
dm mpath: delay retry of bypassed pg
dm mpath: reduce size of struct multipath
This patch implements two new messages that can be sent to the thin
pool target allowing it to take a snapshot of the _metadata_. This,
read-only snapshot can be accessed by userland, concurrently with the
live target.
Only one metadata snapshot can be held at a time. The pool's status
line will give the block location for the current msnap.
Since version 0.1.5 of the userland thin provisioning tools, the
thin_dump program displays the msnap as follows:
thin_dump -m <msnap root> <metadata dev>
Available here: https://github.com/jthornber/thin-provisioning-tools
Now that userland can access the metadata we can do various things
that have traditionally been kernel side tasks:
i) Incremental backups.
By using metadata snapshots we can work out what blocks have
changed over time. Combined with data snapshots we can ensure
the data doesn't change while we back it up.
A short proof of concept script can be found here:
https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb
ii) Migration of thin devices from one pool to another.
iii) Merging snapshots back into an external origin.
iv) Asyncronous replication.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use dedicated caches prefixed with a "dm_" name rather than relying on
kmalloc mempools backed by generic slab caches so the memory usage of
thin provisioning (and any leaks) can be accounted for independently.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
After the failure of a group of paths, any alternative paths that
need initialising do not become available until further I/O is sent to
the device. Until this has happened, ioctls return -EAGAIN.
With this patch, new paths are made available in response to an ioctl
too. The processing of the ioctl gets delayed until this has happened.
Instead of returning an error, we submit a work item to kmultipathd
(that will potentially activate the new path) and retry in ten
milliseconds.
Note that the patch doesn't retry an ioctl if the ioctl itself fails due
to a path failure. Such retries should be handled intelligently by the
code that generated the ioctl in the first place, noting that some SCSI
commands should not be retried because they are not idempotent (XOR write
commands). For commands that could be retried, there is a danger that
if the device rejected the SCSI command, the path could be errorneously
marked as failed, and the request would be retried on another path which
might fail too. It can be determined if the failure happens on the
device or on the SCSI controller, but there is no guarantee that all
SCSI drivers set these flags correctly.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If I/O needs retrying and only bypassed priority groups are available,
set the pg_init_delay_retry flag to wait before retrying.
If, for example, the reason for the bypass is that the controller is
getting reset or there is a firmware upgrade happening, retrying right
away would cause a flood of log messages and retries for what could be a
few seconds or even several minutes.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move multipath structure's 'lock' and 'queue_size' members to eliminate
two 4-byte holes. Also use a bit within a single unsigned int for each
existing flag (saves 8-bytes). This allows future flags to be added
without each consuming an unsigned int.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Pull networking updates from David Miller:
1) Make syn floods consume significantly less resources by
a) Not pre-COW'ing routing metrics for SYN/ACKs
b) Mirroring the device queue mapping of the SYN for the SYN/ACK
reply.
Both from Eric Dumazet.
2) Fix calculation errors in Byte Queue Limiting, from Hiroaki SHIMODA.
3) Validate the length requested when building a paged SKB for a
socket, so we don't overrun the page vector accidently. From Jason
Wang.
4) When netlabel is disabled, we abort all IP option processing when we
see a CIPSO option. This isn't the right thing to do, we should
simply skip over it and continue processing the remaining options
(if any). Fix from Paul Moore.
5) SRIOV fixes for the mellanox driver from Jack orgenstein and Marcel
Apfelbaum.
6) 8139cp enables the receiver before the ring address is properly
programmed, which potentially lets the device crap over random
memory. Fix from Jason Wang.
7) e1000/e1000e fixes for i217 RST handling, and an improper buffer
address reference in jumbo RX frame processing from Bruce Allan and
Sebastian Andrzej Siewior, respectively.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
fec_mpc52xx: fix timestamp filtering
mcs7830: Implement link state detection
e1000e: fix Rapid Start Technology support for i217
e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()
r8169: call netif_napi_del at errpaths and at driver unload
tcp: reflect SYN queue_mapping into SYNACK packets
tcp: do not create inetpeer on SYNACK message
8139cp/8139too: terminate the eeprom access with the right opmode
8139cp: set ring address before enabling receiver
cipso: handle CIPSO options correctly when NetLabel is disabled
net: sock: validate data_len before allocating skb in sock_alloc_send_pskb()
bql: Avoid possible inconsistent calculation.
bql: Avoid unneeded limit decrement.
bql: Fix POSDIFF() to integer overflow aware.
net/mlx4_core: Fix obscure mlx4_cmd_box parameter in QUERY_DEV_CAP
net/mlx4_core: Check port out-of-range before using in mlx4_slave_cap
net/mlx4_core: Fixes for VF / Guest startup flow
net/mlx4_en: Fix improper use of "port" parameter in mlx4_en_event
net/mlx4_core: Fix number of EQs used in ICM initialisation
net/mlx4_core: Fix the slave_id out-of-range test in mlx4_eq_int
Pull straggler x86 fixes from Peter Anvin:
"Three groups of patches:
- EFI boot stub documentation and the ability to print error messages;
- Removal for PTRACE_ARCH_PRCTL for x32 (obsolete interface which
should never have been ported, and the port is broken and
potentially dangerous.)
- ftrace stack corruption fixes. I'm not super-happy about the
technical implementation, but it is probably the least invasive in
the short term. In the future I would like a single method for
nesting the debug stack, however."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32
x86, efi: Add EFI boot stub documentation
x86, efi; Add EFI boot stub console support
x86, efi: Only close open files in error path
ftrace/x86: Do not change stacks in DEBUG when calling lockdep
x86: Allow nesting of the debug stack IDT setting
x86: Reset the debug_stack update counter
ftrace: Use breakpoint method to update ftrace caller
ftrace: Synchronize variable setting with breakpoints
This reverts the tty layer change to use per-tty locking, because it's
not correct yet, and fixing it will require some more deep surgery.
The main revert is d29f3ef39b ("tty_lock: Localise the lock"), but
there are several smaller commits that built upon it, they also get
reverted here. The list of reverted commits is:
fde86d3108 - tty: add lockdep annotations
8f6576ad47 - tty: fix ldisc lock inversion trace
d3ca8b64b9 - pty: Fix lock inversion
b1d679afd7 - tty: drop the pty lock during hangup
abcefe5fc3 - tty/amiserial: Add missing argument for tty_unlock()
fd11b42e35 - cris: fix missing tty arg in wait_event_interruptible_tty call
d29f3ef39b - tty_lock: Localise the lock
The revert had a trivial conflict in the 68360serial.c staging driver
that got removed in the meantime.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
skb_defer_rx_timestamp was called with a freshly allocated skb but must
be called with rskb instead.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add .status callback that detects link state changes.
Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver).
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs fix and a fix from the signal changes for frv from Al Viro.
The __kernel_nlink_t for powerpc got scrogged because 64-bit powerpc
actually depended on the default "unsigned long", while 32-bit powerpc
had an explicit override to "unsigned short". Al didn't notice, and
made both of them be the unsigned short.
The frv signal fix is fallout from simplifying the do_notify_resume()
code, and leaving an extra parenthesis.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
powerpc: Fix size of st_nlink on 64bit
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
frv: Remove bogus closing parenthesis
commit e57f93cc53 (powerpc: get rid of nlink_t uses, switch to
explicitly-sized type) changed the size of st_nlink on ppc64 from
a long to a short, resulting in boot failures.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Introduced by commit 6fd84c0831
("TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.
Also for clarity, rename a few defines as bit definitions instead of masks.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is another fixup where the data is not transfered into buffer
addressed by skb->data but into a page.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Merge fixups for the mac NLS tables from Andrew.
* emailed from Andrew Morton, and one cleanup by me:
nls: fix (and rename) mac NLS table files and config options
fs/nls/Makefile: remove bogus CONFIG_ assignments
The config options in the Kconfig file (with _CODEPAGE_ in the name)
didn't match the config option name in the Makefile (no _CODEPAGE_).
And both of them were of the hard-to-read MACXYZZY variety, which made
them hard to parse for normal humans: MACROMAN easily reads as "macro
man", not as "Mac Roman".
So rename the options to be consistent, and be NLS_MAC_xyzzy. Rename
the files to be mac-xyzzy.c too, and drop the "nls" part entirely (it's
already in the directory name).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These were debug things which snuck through.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Cc: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It includes:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=tmIU
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
video: bfin_adv7393fb: Fix cleanup code
video: exynos_dp: reduce delay time when configuring video setting
video: exynos_dp: move sw reset prioir to enabling sw defined function
video: exynos_dp: use devm_ functions
fb: handle NULL pointers in framebuffer release
OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
OMAPDSS: Apply VENC timings even if panel is disabled
OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
OMAPDSS: DISPC: Support rotation through TILER
OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
OMAPFB: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
video: exynos mipi dsi: support reverse panel type
video: exynos mipi dsi: Properly interpret the interrupt source flags
video: exynos mipi dsi: Avoid races in probe()
...
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
