[how]
Empty dsc enc caps when debug option is set to disable DSC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With different refresh rate panels, the PSR entry/exit time is
different since it is dependent on 2 frame entry time today
[How]
Make static screen num frame entry time to be calculated
such that entry time is within 30 ms instead of fixed num
frames.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PHY will sometimes be in bad state on hotplugging display from USB-C
dongle.
[How]
Add additional calls to disable and then enable PHY before link training
starts during verify_link_cap.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Programming surface flip addresses via dmcub uC for optimizing the data
flush.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Don't want to start HW discovery unless we have lost power,
as doing rediscovery otherwise is both unnecessary and time consuming.
Before this change it takes 40 seconds to go in to suspend, after it
takes 27 seconds
[How]
Accelerated mode gets cleared if we lose power. Only do detection if
this register is cleared
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If the specific monitor supports DSC, the secondary link should be
disabled, and the other way around, too: if either that monitor or
our ASIC doesn't support DSC, the secodary link should be enabled.
[how]
Add a monitor patch and disable secondary link if that monitor
is detected and if ASIC supports DSC, or otherwise enable secondary
link.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It's required for debug purposes.
[how]
Add a dsc_bpp_increment_div debug option that overrides DPCD
BITS_PER_PIXEL_INCREMENT value. The value dsc_bpp_increment_div should
be set to is the one after parsing, i.e. it could be 1, 2, 4, 8 or 16
(meaning 1pix, 1/2pix, ..., 1/16pix).
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc previously had bugs that interfered with the ability to inherit a
timing from a device with multiple streams (without flash/blanking).
After this fix there is still a dependency on UEFI support.
[how]
fixed 3 bugs: loaded MPC state, changed bw_optimize flag to a counter
instead of a boolean, and reading dpp/disp clk from HW to ensure we
don't raise the clock's when we're not supposed to.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to know DP protocol version
[How]
In DC create we initialize a cap to indicate the max
DP protocol version supported
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to be able to enable native 422 for debugging purposes.
[How]
Add new dc_debug_options bool and check it in the get_dsc_enc_caps
function.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need validation that we are programming the expected values (rq, ttu, dlg)
from DML. This debug feature will output logs if we are programming
incorrect values and may help differentiate DAL issues from HW issues.
[How]
Dump relevant registers for each pipe with active stream. Compare current
reg values with the converted DML output. Log mismatches when found.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There can be a conflict between OS HDR multiplier and 3dlut HDR
multiplier, which are both sent to DC.
[HOW]
Instead of having dc determine which HDR multiplier to use, make the
decision in dm and send only the intended value in a surface update.
Store the current OS HDR multiplier and determine whether to use it or
the 3dlut's multiplier before sending the surface update to dc. Send
multiplier to dc in fixed31_32 format, dc then converts it to hw format.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since dcn20 and dcn21 are under dcn1 it doesnt make sense to
have it named dcn1.
Change it to "dcn" to make it generic
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN21 is stable enough to be build by default. So drop the flags.
[How]
Remove them using the unifdef tool. The following commands were executed
in sequence:
$ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DCN2_1 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_1 '{}' ';'
$ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DCN2_1 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_1 '{}' ';'
In addition:
* Remove from kconfig, and replace any dependencies with DCN1_0.
* Remove from any makefiles.
* Fix and cleanup Renoir definitions in dal_asic_id.h
* Expand DCN1 ifdef to include DCN21 code in the following files:
* clk_mgr/clk_mgr.c: dc_clk_mgr_create()
* core/dc_resources.c: dc_create_resource_pool()
* gpio/hw_factory.c: dal_hw_factory_init()
* gpio/hw_translate.c: dal_hw_translate_init()
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN2 and DSC are stable enough to be build by default. So drop the flags.
[How]
Remove them using the unifdef tool. The following commands were executed
in sequence:
$ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';'
$ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';'
In addition:
* Remove from kconfig, and replace any dependencies with DCN1_0.
* Remove from any makefiles.
* Fix and cleanup NV defninitions in dal_asic_id.h
* Expand DCN1 ifdef to include DCN2 code in the following files:
* clk_mgr/clk_mgr.c: dc_clk_mgr_create()
* core/dc_resources.c: dc_create_resource_pool()
* dce/dce_dmcu.c: dcn20_*lock_phy()
* dce/dce_dmcu.c: dcn20_funcs
* dce/dce_dmcu.c: dcn20_dmcu_create()
* gpio/hw_factory.c: dal_hw_factory_init()
* gpio/hw_translate.c: dal_hw_translate_init()
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
When reading link, update the procedure as follows:
1-Set aux timeout to extended: 3.2ms
2-Start with reading lttpr caps
3-Determine if lttpr support should be enabled. Reset aux timeout to
400us if no repeater is found.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It has been a useful option in debugging GFXOFF and P.State Change issues.
May be required as for platform specific workaround.
[HOW]
Create option in enum dc_debug_options, "disable_vactive_clock_change".
When it is set, dm_dram_clock_change_vactive, will translate into
p_state_change_support: false.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For unknown reason, immediate flip with host VM translation on NV12
surface will underflow on last row of PTE.
[How]
Hack chroma viewport height to make fetch one more row of PTE.
Note that this will cause hubp underflow on all video underlay
cases, but the underflow is not user visible since it is in
blank region.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Support for DMUB only depends on support for DC. It doesn't use floating
point so we don't need to guard it by any specific DCN revision.
[How]
Drop the guards and cleanup the newlines around each one.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC will use DMUB for command submission and flow control during
initialization.
Register offloading as well as submitting some BIOS commands are part
of the DC internal interface but are guarded behind debug options.
It won't be functional in amdgpu_dm yet since we don't pass the
DMUB service to DC for use.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
SLT tests require that diag can drive eDP even if nothing is connected, this is not
typical production use case, so we need to add flag
[how]
add flag, and this flag supercedes "should destroy" logic
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System hang during S0i3 if DP only connected due to clk is disabled when
doing link training.
During S0i3, clk is disabled while the clk state is updated when ini_hw
called, and at the moment clk is still disabled which indicating a wrong
state for next time trying to enable clk.
[How]
Add an unknown state and initialize it during int_hw, make sure enable clk
command be sent to smu.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Hard to determine if pipe combine is done with MPC or ODM
[how]
Add new visual confirm type, this will mark each MPCC tree
with a different color
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
1-add configurable timeout support to aux engine.
2-add timeout support field to dc_caps
3-add reg_key to override extended timeout support
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
use vbios message to call smu for dpm level
also only program dmdata in vsyncflip as HW requirement.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HPD is not suppressed when we lower
clocks on renoir. B/c of this we do link
training when the 48mhz refclk is off, which
will cause ASIC hang.
[how]
Exit optimized power state for detection purpose.
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to update the hdcp display parameter whenever the link is
updated, so the next time there is an update to hdcp we have the
latest display info
[How]
Create a callback, and use this anytime there is a change in the link. This will
be used later by the dm.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Presently, there is no way for clocks to be lowered, only raised.
[HOW]
Compare clock status against previous known clock status, and optimize
if different.
This requires re-ordering the layout of the dc_clocks structure, as the
current ordering allows identical clock states to appear different.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Separating the hardware initialization from the creation of the
dc structures gives greater flexibility to the dm to override
options for debugging.
[How]
Move the hardware initialization call to a new function,
dc_hardware_init. No functional change is intended.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc_destroy should only clean up SW, this is because GPUs may be
removed before driver unload, leading to HW to be unavailable.
[how]
remove GPIO close as part of GPIO destroy, this is unnecessary because
GPIO is not shared, and GPIOs are generally closed after being opened
Add tracking to HW access during destructor to make future issues
easier to pinpoint, and block access to prevent hangs.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
