With SYSTEMPORT Lite we have holes in our statistics layout that make us
skip over the hardware MIB counters, bcm_sysport_get_stats() was not
taking that into account resulting in reporting 0 for all SW-maintained
statistics, fix this by skipping accordingly.
Fixes: 44a4524c54 ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if the NIC fails to validate the checksum on TCP/UDP, and validation of IP
checksum is successful, the driver subtracts the pseudo-header checksum
from the value obtained by the hardware and sets CHECKSUM_COMPLETE. Don't
do that if protocol is IPPROTO_SCTP, otherwise CRC32c validation fails.
V2: don't test MLX4_CQE_STATUS_IPV6 if MLX4_CQE_STATUS_IPV4 is set
Reported-by: Shuang Li <shuali@redhat.com>
Fixes: f8c6455bb0 ("net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate 'p_info->mfw_mb_cur' and 'p_info->mfw_mb_shadow' but we check
'p_info->mfw_mb_addr' instead of 'p_info->mfw_mb_cur'.
'p_info->mfw_mb_addr' is never 0, because it is initiliazed a few lines
above in 'qed_load_mcp_offsets()'.
Update the test and check the result of the 2 'kzalloc()' instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even the driver doesn't do anything with the clk source for SGMII
ports it needs to be enabled by doing a devm_clk_get(), if there is
a clk source in DT.
Fixes: 0db01097ca ('xgene: Don't fail probe, if there is no clk resource for SGMII interfaces')
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Tested-by: Laura Abbott <labbott@redhat.com>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each multicast group (MID) stores a bitmap of ports to which a packet
should be forwarded to in case an MDB entry associated with the MID is
hit.
Since the initial introduction of IGMP snooping in commit 3a49b4fde2
("mlxsw: Adding layer 2 multicast support") the driver didn't correctly
free these multicast groups upon ungraceful situations such as the
removal of the upper bridge device or module removal.
The correct way to fix this is to associate each MID with the bridge
ports member in it and then drop the reference in case the bridge port
is destroyed, but this will result in a lot more code and will be fixed
in net-next.
For now, upon module removal, traverse the MID list and release each
one.
Fixes: 3a49b4fde2 ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some operations in the bridge driver such as MDB deletion are preformed
in an atomic context and thus deferred to a process context by the
switchdev infrastructure.
Therefore, by the time the operation is performed by the underlying
device driver it's possible the bridge port context is already gone.
This is especially true for removal flows, but theoretically can also be
invoked during addition.
Remove the warnings in such situations and return normally.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Fixes: 3922285d96 ("net: bridge: Add support for offloading port attributes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCRQ resources are freed during renegotiation, but they are not
re-allocated afterwards due to some changes in the initialization
process. Fix that by re-allocating the memory after renegotation.
SCRQ's can also be freed if a server capabilities request fails.
If this were encountered during a device reset for example,
SCRQ's may not be re-allocated. This operation is not necessary
anymore so remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cited commit introduced the following new enum value in file
include/linux/mlx4/device.h:
QUERY_DEV_CAP_DIAG_RPRT_PER_PORT
However, it failed to introduce a corresponding entry in function
dump_dev_cap_flags2() for outputting a line in the message log
when this capability bit is set.
The change here fixes that omission.
Fixes: c7c122ed67 ("net/mlx4: Add diagnostic counters capability bit")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cited commit introduced the following new enum value in file
include/linux/mlx4/device.h:
MLX4_DEV_CAP_FLAG2_SVLAN_BY_QP
However the value of MLX4_DEV_CAP_FLAG2_SVLAN_BY_QP needs to stay
consistent with the value used in another namespace in
function dump_dev_cap_flags2(), which is manually kept in sync.
The change here restores that consistency.
Fixes: 7c3d21c815 ("net/mlx4_core: Preparation for VF vlan protocol 802.1ad")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The index value in function dump_dev_cap_flags2() for outputting
"sl to vl mapping table change event support" needs to be
consistent with the value of the enumerated constant
MLX4_DEV_CAP_FLAG2_SL_TO_VL_CHANGE_EVENT defined in file
include/linux/mlx4_device.h
The change here restores that consistency.
Fixes: fd10ed8e6f ("IB/mlx4: Fix possible vl/sl field mismatch in LRH header in QP1 packets")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when WoL is supported but disabled, ethtool reports:
"Supports Wake-on: d".
Fix the indication of Wol support, so that the indication
remains "g" all the time if the NIC supports WoL.
Tested:
As accepted, when NIC supports WoL- ethtool reports:
Supports Wake-on: g
Wake-on: d
when NIC doesn't support WoL- ethtool reports:
Supports Wake-on: d
Wake-on: d
Fixes: 14c07b1358 ("mlx4: Wake on LAN support")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that.
Fixes: 4c3523623d ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that.
Fixes: 4197aa7bb8 ("ixgbevf: provide 64 bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that.
Fixes: 980e9b1186 ("i40e: Add support for 64 bit netstats")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that.
Fixes: eeda858552 ("b44: add 64 bit stats")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the call chain
cpts_find_ts()
|- cpts_fifo_read(cpts, CPTS_EV_PUSH)
will stop reading CPTS FIFO if PUSH event is found. But this is not
expected and CPTS FIFI should be completely drained here. This is most
probably copy-paste error and it has no negative impact as CPTS_EV_PUSH
should not be present in FIFO without TS_PUSH request and
cpts_systim_read() and cpts_find_ts() synchronized by spin_lock.
Correct above by calling cpts_fifo_read() with -1 parameter, so it will
read all CPTS event from FIFO.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the low speed Ethernet connection CPDMA notification about packet
processing can be received before CPTS TX timestamp event, which is set
when packet actually left CPSW while cpdma notification is sent when packet
pushed in CPSW fifo. As result, when connection is slow and CPU is fast
enough TX timestamping is not working properly.
Fix it, by introducing TX SKB queue to store PTP SKBs for which Ethernet
Transmit Event hasn't been received yet and then re-check this queue
with new Ethernet Transmit Events by scheduling CPTS overflow
work more often (every 1 jiffies) until TX SKB queue is not empty.
Side effect of this change is:
- User space tools require to take into account possible delay in TX
timestamp processing (for example ptp4l works with tx_timestamp_timeout=400
under net traffic and tx_timestamp_timeout=25 in idle).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There could be significant delay in CPTS work schedule under high system
load and on -RT which could cause CPTS misbehavior due to internal counter
overflow. Usage of own kthread_worker allows to avoid such kind of issues
and makes it possible to tune priority of CPTS kthread_worker thread on -RT
(thread name "cpts").
Hence, the CPTS driver is converted to use PTP auxiliary worker as PHC
subsystem implements such functionality in a generic way now.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 28b45910cc ("net: bcmgenet: Remove init parameter
from bcmgenet_mii_config") because in the process of moving from
dev_info() to dev_info_once() we essentially lost the helpful printed
messages once the second instance of the driver is loaded.
dev_info_once() does not actually print the message once per device
instance, but once period.
Fixes: 28b45910cc ("net: bcmgenet: Remove init parameter from bcmgenet_mii_config")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_irq_to_resource() has recently been fixed to return negative error #'s
along with 0 in case of failure, however the Marvell MV643xx Ethernet
driver still only regards 0 as invalid IRQ -- fix it up.
Fixes: 7a4228bbff ("of: irq: use of_irq_get() in of_irq_to_resource()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the values to match those from the STP2002QFP documentation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in printk message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SGMII/RGMII/QSGMII interfaces when physical link goes down
while traffic is high is resulting in underflow condition being set
on that specific BGX's LMAC. Which assets a backpresure and VNIC stops
transmitting packets.
This is due to BGX being disabled in link status change callback while
packet is in transit. This patch fixes this issue by not disabling BGX
but instead just disables packet Rx and Tx.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding ethtool steering rule with action DISCARD we wrongly
pass a NULL dest with dest_num 1 to mlx5_add_flow_rules().
What this error seems to have caused is sending VPORT 0
(MLX5_FLOW_DESTINATION_TYPE_VPORT) as the fte dest instead of no dests.
We have fte action correctly set to DROP so it might been ignored
anyways.
To reproduce use:
# sudo ethtool --config-nfc <dev> flow-type ether \
dst aa:bb:cc:dd:ee:ff action -1
Fixes: 74491de937 ("net/mlx5: Add multi dest support")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This is done in order to ensure that work will not run after the cleanup.
Fixes: ef9814deaf ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The overflow_period is calculated in seconds. In order to use it
for delayed work scheduling translation to jiffies is needed.
Fixes: ef9814deaf ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the missing option to enable the PTP_CLK_PPS function.
In this case pin should be configured as 1PPS IN first and
then it will be connected to PPS mechanism.
Events will be reported as PTP_CLOCK_PPSUSR events to relevant sysfs.
Fixes: ee7f12205a ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to fix the drift in 1PPS out need to adjust the next pulse.
On each 1PPS out falling edge driver gets the event, then the event
handler adjusts the next pulse starting time.
Fixes: ee7f12205a ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Need to disable the MTPPS and unsubscribe from the pulse events
when user disables the 1PPS functionality.
Fixes: ee7f12205a ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to mark relevant fields while setting the MTPPS register
add field select. Otherwise it can cause a misconfiguration in
firmware.
Fixes: ee7f12205a ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
outer_header_zero() routine checks if the outer_headers match of a
flow-table entry are all zero.
This function uses the size of whole fte_match_param, instead of just
the outer_headers member, causing failure to detect all-zeros if
any other members of the fte_match_param are non-zero.
Use the correct size for zero check.
Fixes: 6dc6071cfc ("net/mlx5e: Add ethtool flow steering support")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On interface remove, the clean-up was done incorrectly causing
an error in the log:
"SET_FLOW_TABLE_ROOT(0x92f) op_mod(0x0) failed...syndrome (0x7e9f14)"
This was caused by the following flow:
-ndo_uninit:
Move QP state to RST (this disconnects the QP from FT),
the QP cannot be attached to any FT unless it is in RTS.
-mlx5_rdma_netdev_free:
cleanup_rx: Destroy FT
cleanup_tx: Destroy QP and remove QPN from FT
This caused a problem when destroying current FT we tried to
re-attach the QP to the next FT which is not needed.
The correct flow is:
-mlx5_rdma_netdev_free:
cleanup_rx: remove QPN from FT & Destroy FT
cleanup_tx: Destroy QP
Fixes: 508541146a ("net/mlx5: Use underlay QPN from the root name space")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When driver fail to allocate an entry to send command to FW, it must
notify the calling function and release the memory allocated for
this command.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Completion on timeout should not free the driver command entry structure
as it will need to access it again once real completion event from FW
will occur.
Fixes: 73dd3a4839 ('net/mlx5: Avoid using pending command interface slots')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The tx_enabled lag event field is used to determine whether a slave is
active.
Current logic uses this value only if the mode is active-backup.
However, LACP mode, although considered a load balancing mode, can mark
a slave as inactive in certain situations (e.g., LACP timeout).
This fix takes the tx_enabled value into account when remapping, with
no respect to the LAG mode (this should not affect the behavior in XOR
mode, since in this mode both slaves are marked as active).
Fixes: 7907f23adc (net/mlx5: Implement RoCE LAG feature)
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Upon sriov enable, eswitch is always enabled.
Currently, if enable hca failed over all VFs, we would skip eswitch
disable as part of sriov disable, which will lead to resources leak.
Fix it by disabling eswitch if it was enabled (use indication from
eswitch mode).
Fixes: 6b6adee3da ('net/mlx5: SRIOV core code refactoring')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Before commit bf8f6952a2 ("Add blurb about RGMII") it was unclear
whose responsibility it was to insert the required clock skew, and
in hindsight, some PHY drivers got it wrong. The solution forward
is to introduce a new property, explicitly requiring skew from the
node to which it is attached. In the interim, this driver will handle
all 4 RGMII modes identically (no skew).
Fixes: 52dfc83012 ("net: ethernet: add driver for Aurora VLSI NB8800 Ethernet controller")
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error paths set err, but it's not returned.
I wondered if we should fix all of the callers to check the returned
value, but Ben explains why the code is this way:
> Most call sites ignore it on purpose. There's nothing we can do if
> we fail to get a buffer at interrupt time, so we point the buffer to
> the scratch page so the HW doesn't DMA into lalaland and lose the
> packet.
>
> The one call site that tests and can fail is the one used when brining
> the interface up. If we fail to allocate at that point, we fail the
> ifup. But as you noticed, I do have a bug not returning the error.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate mii_bus->parent with our own platform device before
registering, which makes it easier to locate the MDIO bus
in sysfs when trying to diagnose problems.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had reports of 50us not being sufficient to reset the MAC,
thus hitting the "Hardware reset failed" error bringing the
interface up on some AST2400 based machines.
This bumps the timeout to 200us.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit fbf68229ff ("net: stmmac: unify registers dumps methods")
in the Linux kernel modified the register dump to store the DMA registers
at the DMA register offset (0x1000) but ethtool (stmmac.c) looks for the
DMA registers after the MAC registers which is offset 55.
This patch copies the DMA registers from the higher offset to the offset
where ethtool expects them.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each FIB node holds a linked list of routes sharing the same prefix and
length. In the case of IPv4 it's ordered according to table ID, metric
and TOS and only the first route in the list is actually programmed to
the device.
In case a gatewayed route is added somewhere in the list, then after its
nexthop group will be refreshed and become valid (due to the resolution
of its gateway), it'll mistakenly overwrite the existing entry.
Example:
192.168.200.0/24 dev enp3s0np3 scope link metric 1000 offload
192.168.200.0/24 via 192.168.100.1 dev enp3s0np3 metric 1000 offload
Both routes are marked as offloaded despite the fact only the first one
should actually be present in the device's table.
When refreshing the nexthop group, don't write the route to the device's
table unless it's the first in its node.
Fixes: 9aecce1c7d ("mlxsw: spectrum_router: Correctly handle identical routes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mediatek ethernet driver uses interrupts but does not explicitly
include linux/interrupt.h, relying on implicit includes. Fix this so we
don't get build breaks as happened for ARM in next-20170720.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Potential dangerous invalid memory might be accessed if invalid mac value
reflected from the forward port field in rxd4 caused by possible potential
hardware defects. So added a simple sanity checker to avoid the kind of
situation happening.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) BPF verifier signed/unsigned value tracking fix, from Daniel
Borkmann, Edward Cree, and Josef Bacik.
2) Fix memory allocation length when setting up calls to
->ndo_set_mac_address, from Cong Wang.
3) Add a new cxgb4 device ID, from Ganesh Goudar.
4) Fix FIB refcount handling, we have to set it's initial value before
the configure callback (which can bump it). From David Ahern.
5) Fix double-free in qcom/emac driver, from Timur Tabi.
6) A bunch of gcc-7 string format overflow warning fixes from Arnd
Bergmann.
7) Fix link level headroom tests in ip_do_fragment(), from Vasily
Averin.
8) Fix chunk walking in SCTP when iterating over error and parameter
headers. From Alexander Potapenko.
9) TCP BBR congestion control fixes from Neal Cardwell.
10) Fix SKB fragment handling in bcmgenet driver, from Doug Berger.
11) BPF_CGROUP_RUN_PROG_SOCK_OPS needs to check for null __sk, from Cong
Wang.
12) xmit_recursion in ppp driver needs to be per-device not per-cpu,
from Gao Feng.
13) Cannot release skb->dst in UDP if IP options processing needs it.
From Paolo Abeni.
14) Some netdev ioctl ifr_name[] NULL termination fixes. From Alexander
Levin and myself.
15) Revert some rtnetlink notification changes that are causing
regressions, from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
net: bonding: Fix transmit load balancing in balance-alb mode
rds: Make sure updates to cp_send_gen can be observed
net: ethernet: ti: cpsw: Push the request_irq function to the end of probe
ipv4: initialize fib_trie prior to register_netdev_notifier call.
rtnetlink: allocate more memory for dev_set_mac_address()
net: dsa: b53: Add missing ARL entries for BCM53125
bpf: more tests for mixed signed and unsigned bounds checks
bpf: add test for mixed signed and unsigned bounds checks
bpf: fix up test cases with mixed signed/unsigned bounds
bpf: allow to specify log level and reduce it for test_verifier
bpf: fix mixed signed/unsigned derived min/max value bounds
ipv6: avoid overflow of offset in ip6_find_1stfragopt
net: tehuti: don't process data if it has not been copied from userspace
Revert "rtnetlink: Do not generate notifications for CHANGEADDR event"
net: dsa: mv88e6xxx: Enable CMODE config support for 6390X
dt-binding: ptp: Add SoC compatibility strings for dte ptp clock
NET: dwmac: Make dwmac reset unconditional
net: Zero terminate ifr_name in dev_ifname().
wireless: wext: terminate ifr name coming from userspace
netfilter: fix netfilter_net_init() return
...
Push the request_irq function to the end of probe so as
to ensure all the required fields are populated in the event
of an ISR getting executed right after requesting the irq.
Currently while loading the crash kernel a crash was seen as
soon as devm_request_threaded_irq was called. This was due to
n->poll being NULL which is called as part of net_rx_action
function.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The array data is only populated with valid information from userspace
if cmd != SIOCDEVPRIVATE, other cases the array contains garbage on
the stack. The subsequent switch statement acts on a subcommand in
data[0] which could be any garbage value if cmd is SIOCDEVPRIVATE which
seems incorrect to me. Instead, just return EOPNOTSUPP for the case
where cmd == SIOCDEVPRIVATE to avoid this issue.
As a side note, I suspect that the original intention of the code
was for this ioctl to work just for cmd == SIOCDEVPRIVATE (and the
current logic is reversed). However, I don't wont to change the current
semantics in case any userspace code relies on this existing behaviour.
Detected by CoverityScan, CID#139647 ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unconditional reset dwmac before HW init if reset controller is present.
In existing implementation we reset dwmac only after second module
probing:
(module load -> unload -> load again [reset happens])
Now we reset dwmac at every module load:
(module load [reset happens] -> unload -> load again [reset happens])
Also some reset controllers have only reset callback instead of
assert + deassert callbacks pair, so handle this case.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller to the driver marks GFP_NOIO allocations with help
of memalloc_noio-* calls now. This makes redundant to pass down
to the driver gfp flags, which can be GFP_KERNEL only.
The patch removes the gfp flags argument and updates all driver paths.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Since the skb is attached to the first control block of a fragmented
skb it is possible that the skb could be freed when reclaiming that
control block before all fragments of the skb have been consumed by
the hardware and unmapped.
This commit introduces first_cb and last_cb pointers to the skb
control block used by the driver to keep track of which transmit
control blocks within a transmit ring are the first and last ones
associated with the skb.
It then splits the bcmgenet_free_cb() function into transmit
(bcmgenet_free_tx_cb) and receive (bcmgenet_free_rx_cb) versions
that can handle the unmapping of dma mapped memory and cleaning up
the corresponding control block structure so that the skb is only
freed after the last associated transmit control block is reclaimed.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
