We should unregister the net_device first, before we give back
our reference on xdp_prog. Otherwise xdp_prog may be freed
before .ndo_stop() disabled the datapath. Found by code inspection.
Fixes: ecd63a0217 ("nfp: add XDP support in the driver")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI's cpsw driver handles both OF and non-OF case for phy
connect. Unfortunately of_phy_connect() returns NULL on
error while phy_connect() returns ERR_PTR().
To handle this, cpsw_slave_open() overrides the return value
from phy_connect() to make it NULL or error.
This leaves a small window, where cpsw_adjust_link() may be
invoked for a slave while slave->phy pointer is temporarily
set to -ENODEV (or some other error) before it is finally set
to NULL.
_cpsw_adjust_link() only handles the NULL case, and an oops
results when ERR_PTR() is seen by it.
Note that cpsw_adjust_link() checks PHY status for each
slave whenever it is invoked. It can so happen that even
though phy_connect() for a given slave returns error,
_cpsw_adjust_link() is still called for that slave because
the link status of another slave changed.
Fix this by using a temporary pointer to store return value
of {of_}phy_connect() and do a one-time write to slave->phy.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trival fix, rename HW_INTERRUT_ASSERT_SET_* to HW_INTERRUPT_ASSERT_SET_*
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case, if TX watchdog is fired some or all netdev TX queues will be
stopped and as part of recovery it is required not only to drain and
reinitailize CPSW TX channeles, but also wake up stoppted TX queues what
doesn't happen now and netdevice will stop transmiting data until
reopenned.
Hence, add netif_tx_wake_all_queues() call in .ndo_tx_timeout() to complete
recovery and restore TX path.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses interfaces from linux/of.h and linux/property.h but
relies on implict inclusion of those headers which means that changes in
other headers could break the build, as happened in -next for arm today.
Add a explicit includes.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code only supports DT to check SFP present.
This patch adds ACPI support as well.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpu_to_le32() for link_config variable in set_logical_link_config
command as this variable is of type u32.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a new NAPI_STATE_MISSED state was added to NAPI we can get into
this state and in such case we have to reschedule NAPI as some work is
still pending and we have to process it. napi_complete_done() function
returns false if we have to reschedule something (e.g. in case we were
in MISSED state) as current polling have not been completed yet.
nps_enet driver hasn't been verifying the return value of
napi_complete_done() and has been forcibly enabling interrupts. That is
not correct as we should not enable interrupts before we have processed
all scheduled work. As a result we were getting trapped in interrupt
hanlder chain as we had never been able to disabale ethernet
interrupts again.
So this patch makes nps_enet_poll() func verify return value of
napi_complete_done() and enable interrupts only in case all scheduled
work has been completed.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_free_rx_skbs(), which is called to free up all RX buffers during
shutdown, we need to unmap the page if we are running in XDP mode.
Fixes: c61fb99cae ("bnxt_en: Add RX page mode support.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sankar Patchineelam <sankar.patchineelam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Net device reset can fail when the h/w or f/w is in a bad state.
Subsequent netdevice open fails in bnxt_hwrm_stat_ctx_alloc().
The cleanup invokes bnxt_hwrm_resource_free() which inturn
calls bnxt_disable_int(). In this routine, the code segment
if (ring->fw_ring_id != INVALID_HW_RING_ID)
BNXT_CP_DB(cpr->cp_doorbell, cpr->cp_raw_cons);
results in NULL pointer dereference as cpr->cp_doorbell is not yet
initialized, and fw_ring_id is zero.
The fix is to initialize cpr fw_ring_id to INVALID_HW_RING_ID before
bnxt_init_chip() is invoked.
Signed-off-by: Sankar Patchineelam <sankar.patchineelam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-7 reports a warning that earlier versions did not have:
drivers/net/ethernet/rocker/rocker_ofdpa.c: In function 'ofdpa_port_stp_update':
arch/x86/include/asm/string_32.h:79:22: error: '*((void *)&prev_ctrls+4)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*((short *)to + 2) = *((short *)from + 2);
~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/rocker/rocker_ofdpa.c:2218:7: note: '*((void *)&prev_ctrls+4)' was declared here
This is clearly a variation of the warning about 'prev_state' that
was shut up using uninitialized_var().
We can slightly simplify the code and get rid of the warning by unconditionally
saving the prev_state and prev_ctrls variables. The inlined memcpy is not
particularly expensive here, as it just has to read five bytes from one or
two cache lines.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In NETDEV_CHANGEUPPER event the upper_info field is valid
only when linking is true. Otherwise it should be ignored.
Fixes: 7907f23adc (net/mlx5: Implement RoCE LAG feature)
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Reviewed-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
moxart_mac_start_xmit() doesn't care where tx_tail is, tx_head can
catch and pass tx_tail, which is bad because moxart_tx_finished()
isn't guaranteed to catch up on freeing resources from tx_tail.
Add a check in moxart_mac_start_xmit() stopping the queue at the
end of the circular buffer. Also add a check in moxart_tx_finished()
waking the queue if the buffer has TX_WAKE_THRESHOLD or more
free descriptors.
While we're at it, move spin_lock_irq() to happen before our
descriptor pointer is assigned in moxart_mac_start_xmit().
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=99451
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns_dsaf_set_mac_key() calls dsaf_set_field() on an uninitialized field,
which will then change only a few of its bits, causing a warning with
the latest gcc:
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_set_mac_uc_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
(origin) &= (~(mask)); \
^~
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_set_mac_mc_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_add_mac_mc_port':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_del_mac_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_rm_mac_addr':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_del_mac_mc_port':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_mac_uc_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_mac_mc_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code is actually correct since we always set all 16 bits of the
port_vlan field, but gcc correctly points out that the first
access does contain uninitialized data.
This initializes the field to zero first before setting the
individual bits.
Fixes: 5483bfcb16 ("net: hns: modify tcam table and set mac key")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dev_dbg() is enabled, we print uninitialized data, as gcc-7.0.1
now points out:
ethernet/hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_set_promisc_tcam':
ethernet/hisilicon/hns/hns_dsaf_main.c:2947:75: error: 'tbl_tcam_data.low.val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
ethernet/hisilicon/hns/hns_dsaf_main.c:2947:75: error: 'tbl_tcam_data.high.val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
We also pass the data into hns_dsaf_tcam_mc_cfg(), which might later
use it (not sure about that), so it seems safer to just always initialize
the tbl_tcam_data structure.
Fixes: 1f5fa2dd1c ("net: hns: fix for promisc mode in HNS driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing the epoll w/ busy poll code I found that I could get into a
state where the i40e driver had q_vectors w/ active NAPI that had no rings.
This was resulting in a divide by zero error. To correct it I am updating
the driver code so that we only support NAPI on q_vectors that have 1 or
more rings allocated to them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 7e54d9d063.
After additional regression testing, several users are experiencing
kernel panics during shutdown on e1000e devices. Reverting this
change resolves the issue.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The latest gcc-7 snapshot warns about bfa_ioc_send_enable/bfa_ioc_send_disable
writing undefined values into the hardware registers:
drivers/net/ethernet/brocade/bna/bfa_ioc.c: In function 'bfa_iocpf_sm_disabling_entry':
arch/arm/include/asm/io.h:109:22: error: '*((void *)&disable_req+4)' is used uninitialized in this function [-Werror=uninitialized]
arch/arm/include/asm/io.h:109:22: error: '*((void *)&disable_req+8)' is used uninitialized in this function [-Werror=uninitialized]
The two functions look like they should do the same thing, but only one
of them initializes the time stamp and clscode field. The fact that we
only get a warning for one of the two functions seems to be arbitrary,
based on the inlining decisions in the compiler.
To address this, I'm making both functions do the same thing:
- set the clscode from the ioc structure in both
- set the time stamp from ktime_get_real_seconds (which also
avoids the signed-integer overflow in 2038 and extends the
well-defined behavior until 2106).
- zero-fill the reserved field
Fixes: 8b230ed8ec ("bna: Brocade 10Gb Ethernet device driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to reset is_gso flag when EOP reached (entire LSO packet processed).
Fixes: bab6de8fd1 ("net: ethernet: aquantia:
Atlantic A0 and B0 specific functions.")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Context Command bit: L3 type = "0" for IPv4, "1" for IPv6.
Fixes: bab6de8fd1 ("net: ethernet: aquantia:
Atlantic A0 and B0 specific functions.")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix for missing initialization aq_ring header.lock spinlock.
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the checksum offloads to work correctly we need to set the
packet type bit (TCP/UDP) in the TX context buffer.
Fixes: 97bde5c4f9 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Tested-by: David Arcari <darcari@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Closing/opening the adapter is not needed at all.
The new MTU settings take effect immediately.
Fixes: 97bde5c4f9 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since AQC-100/107/108 chips supports hardware checksums for RX we should indicate this
via NETIF_F_RXCSUM flag.
v1->v2: 'Signed-off-by' tag added.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ECC bit positions that describe whether the ECC interrupt is for
Tx, Rx or descriptor memory and whether the it is a single correctable
or double detected error were defined in incorrectly (reversed order).
Fix the bit position definitions for these settings so that the proper
ECC handling is performed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Presumably if there is an "add" function, there is also a "del"
function. But it causes a static checker warning because it looks like
a common cut and paste bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and
bcmgenet_internal_phy_setup() functions. In so doing it broke the reset
of the internal PHY devices used by the GENETv1-GENETv3 which required
this reset before the UniMAC was enabled. It also broke the internal
GPHY devices used by the GENETv4 because the config_init that installed
the AFE workaround was no longer occurring after the reset of the GPHY
performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup().
In addition the code in bcmgenet_internal_phy_setup() related to the
"enable APD" comment goes with the bcmgenet_mii_reset() so it should
have also been removed.
Commit bd4060a610 ("net: bcmgenet: Power on integrated GPHY in
bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the
bcmgenet_power_up() function, but failed to remove it from the
bcmgenet_internal_phy_setup() function. Had it done so, the
bcmgenet_internal_phy_setup() function would have been empty and could
have been removed at that time.
Commit 5dbebbb44a ("net: bcmgenet: Software reset EPHY after power on")
was submitted to correct the functional problems introduced by
commit 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset"). It
was included in v4.4 and made available on 4.3-stable. Unfortunately,
it didn't fully revert the commit because this bcmgenet_mii_reset()
doesn't apply the soft reset to the internal GPHY used by GENETv4 like
the previous one did. This prevents the restoration of the AFE work-
arounds for internal GPHY devices after the bcmgenet_phy_power_set() in
bcmgenet_internal_phy_setup().
This commit takes the alternate approach of removing the unnecessary
bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3
so that when bcmgenet_mii_reset() was restored it should have only gone
into bcmgenet_power_up(). This will avoid the problems while also
removing the redundancy (and hopefully some of the confusion).
Fixes: 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX packets statistics ('rx_packets' counter) used to count LRO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'rx_lro_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 435277
rx_lro_packets: 35847
rx_packets_phy: 1935066
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 1935066
rx_lro_packets: 35847
rx_packets_phy: 1935066
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX packets statistics ('tx_packets' counter) used to count GSO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'tx_tso_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 61340
tx_tso_packets: 60954
tx_packets_phy: 2451115
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 2451115
tx_tso_packets: 60954
tx_packets_phy: 2451115
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a
limit preventing some applications to allocate needed QPs amount.
Double the size to 256K.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was added to allow the TC offloading code to identify offloading
encap/decap vxlan rules.
The VF reps are effectively related to the same mlx5 PCI device as the
PF. Since the kernel invokes the (say) delete ndo for each netdev, the
FW erred on multiple vxlan dst port deletes when the port was deleted
from the system.
We fix that by keeping the registration to be carried out only by the
PF. Since the PF serves as the uplink device, the VF reps will look
up a port there and realize if they are ok to offload that.
Tested:
<SETUP VFS>
<SETUP switchdev mode to have representors>
ip link add vxlan1 type vxlan id 44 dev ens5f0 dstport 9999
ip link set vxlan1 up
ip link del dev vxlan1
Fixes: 4a25730eb2 ('net/mlx5e: Add ndo_udp_tunnel_add to VF representors')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use the non UAPI values and we miss erring on
the modify action which is not supported, fix that.
Fixes: 8b32580df1 ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the eswitch inline mode can potentially cause already configured
flows not to match the policy. E.g. set policy L4, add some L4 rules,
set policy to L2 --> bad! Hence we disallow it.
Keep track of how many offloaded rules are now set and refuse
inline mode changes if this isn't zero.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code to deal with add/del TC rules to have handler per NIC/E-switch
offloading use case, and push the latter into the e-switch code. This provides
better separation and is to be used in down-stream patch for applying a fix.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch cases for the rate limit set and query commands were
missing, which could get us wrong under fw error or driver reset
flow, fix that.
Fixes: 1466cc5b23 ('net/mlx5: Rate limit tables support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With posix timers having become optional, we get a build error with
the cpts time sync option of the CPSW driver:
drivers/net/ethernet/ti/cpts.c: In function 'cpts_find_ts':
drivers/net/ethernet/ti/cpts.c:291:23: error: implicit declaration of function 'ptp_classify_raw';did you mean 'ptp_classifier_init'? [-Werror=implicit-function-declaration]
This adds a hard dependency on PTP_CLOCK to avoid the problem, as
building it without PTP support makes no sense anyway.
Fixes: baa73d9e47 ("posix-timers: Make them configurable")
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dependency is reversed: cpsw and netcp call into cpts,
but cpts depends on the other two in Kconfig. This can lead
to cpts being a loadable module and its callers built-in:
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_remove':
cpsw.c:(.text.cpsw_remove+0xd0): undefined reference to `cpts_release'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_rx_handler':
cpsw.c:(.text.cpsw_rx_handler+0x2dc): undefined reference to `cpts_rx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_tx_handler':
cpsw.c:(.text.cpsw_tx_handler+0x7c): undefined reference to `cpts_tx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_ndo_stop':
As a workaround, I'm introducing another Kconfig symbol to
control the compilation of cpts, while making the actual
module controlled by a silent symbol that is =y when necessary.
Fixes: 6246168b4a ("net: ethernet: ti: netcp: add support of cpts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We could allocate less memory than intended because we do:
bnad->regdata = kzalloc(len << 2, GFP_KERNEL);
The shift can overflow leading to a crash. This is debugfs code so the
impact is very small.
Fixes: 7afc5dbde0 ("bna: Add debugfs interface.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Rasesh Mody <rasesh.mody@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer array for the tx/rx sub crqs should be free'ed when
releasing the tx/rx sub crqs.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the aquantia device mtu is changed the net_device structure is not
updated. As a result the ip command does not properly reflect the mtu change.
Commit 5513e16421 incorrectly assumed that __dev_set_mtu() was making the
assignment ndev->mtu = new_mtu; This is not true in the case where the driver
has a ndo_change_mtu routine.
Fixes: 5513e16421 ("net: ethernet: aquantia: Fixes for aq_ndev_change_mtu")
Cc: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David Arcari <darcari@redhat.com>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Hypervisors detach VFs from VMs by instantly causing an FLR event
to be generated for a VF.
In the mlx4 case, this will cause that VF's comm channel to be disabled
before the VM has an opportunity to invoke the VF device's "shutdown"
method.
For such Hypervisors, there is a race condition between the VF's
shutdown method and its internal-error detection/reset thread.
The internal-error detection/reset thread (which runs every 5 seconds) also
detects a disabled comm channel. If the internal-error detection/reset
flow wins the race, we still get delays (while that flow tries repeatedly
to detect comm-channel recovery).
The cited commit fixed the command timeout problem when the
internal-error detection/reset flow loses the race.
This commit avoids the unneeded delays when the internal-error
detection/reset flow wins.
Fixes: d585df1c5c ("net/mlx4_core: Avoid command timeouts during VF driver device shutdown")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reported-by: Simon Xiao <sixiao@microsoft.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer hardware does not provide a cumulative payload length when multiple
descriptors are needed to handle the data. Once the MTU increases beyond
the size that can be handled by a single descriptor, the SKB does not get
built properly by the driver.
The driver will now calculate the size of the data buffers used by the
hardware. The first buffer of the first descriptor is for packet headers
or packet headers and data when the headers can't be split. Subsequent
descriptors in a multi-descriptor chain will not use the first buffer. The
second buffer is used by all the descriptors in the chain for payload data.
Based on whether the driver is processing the first, intermediate, or last
descriptor it can calculate the buffer usage and build the SKB properly.
Tested and verified on both old and new hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suspending the PHY would be putting it in a low power state where it
may no longer allow us to do Wake-on-LAN.
Fixes: cc013fb488 ("net: bcmgenet: correctly suspend and resume PHY device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Ensure that mtu is at least IPV6_MIN_MTU in ipv6 VTI tunnel driver,
from Steffen Klassert.
2) Fix crashes when user tries to get_next_key on an LPM bpf map, from
Alexei Starovoitov.
3) Fix detection of VLAN fitlering feature for bnx2x VF devices, from
Michal Schmidt.
4) We can get a divide by zero when TCP socket are morphed into
listening state, fix from Eric Dumazet.
5) Fix socket refcounting bugs in skb_complete_wifi_ack() and
skb_complete_tx_timestamp(). From Eric Dumazet.
6) Use after free in dccp_feat_activate_values(), also from Eric
Dumazet.
7) Like bonding team needs to use ETH_MAX_MTU as netdev->max_mtu, from
Jarod Wilson.
8) Fix use after free in vrf_xmit(), from David Ahern.
9) Don't do UDP Fragmentation Offload on IPComp ipsec packets, from
Alexey Kodanev.
10) Properly check napi_complete_done() return value in order to decide
whether to re-enable IRQs or not in amd-xgbe driver, from Thomas
Lendacky.
11) Fix double free of hwmon device in marvell phy driver, from Andrew
Lunn.
12) Don't crash on malformed netlink attributes in act_connmark, from
Etienne Noss.
13) Don't remove routes with a higher metric in ipv6 ECMP route replace,
from Sabrina Dubroca.
14) Don't write into a cloned SKB in ipv6 fragmentation handling, from
Florian Westphal.
15) Fix routing redirect races in dccp and tcp, basically the ICMP
handler can't modify the socket's cached route in it's locked by the
user at this moment. From Jon Maxwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (108 commits)
qed: Enable iSCSI Out-of-Order
qed: Correct out-of-bound access in OOO history
qed: Fix interrupt flags on Rx LL2
qed: Free previous connections when releasing iSCSI
qed: Fix mapping leak on LL2 rx flow
qed: Prevent creation of too-big u32-chains
qed: Align CIDs according to DORQ requirement
mlxsw: reg: Fix SPVMLR max record count
mlxsw: reg: Fix SPVM max record count
net: Resend IGMP memberships upon peer notification.
dccp: fix memory leak during tear-down of unsuccessful connection request
tun: fix premature POLLOUT notification on tun devices
dccp/tcp: fix routing redirect race
ucc/hdlc: fix two little issue
vxlan: fix ovs support
net: use net->count to check whether a netns is alive or not
bridge: drop netfilter fake rtable unconditionally
ipv6: avoid write to a possibly cloned skb
net: wimax/i2400m: fix NULL-deref at probe
isdn/gigaset: fix NULL-deref at probe
...
Missing in the initial submission, qed fails to propagate qedi's
request to enable OOO to firmware.
Fixes: fc831825f9 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to set the number of entries in database, otherwise the logic
would quickly surpass the array.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before iterating over the the LL2 Rx ring, the ring's
spinlock is taken via spin_lock_irqsave().
The actual processing of the packet [including handling
by the protocol driver] is done without said lock,
so qed releases the spinlock and re-claims it afterwards.
Problem is that the final spin_lock_irqrestore() at the end
of the iteration uses the original flags saved from the
initial irqsave() instead of the flags from the most recent
irqsave(). So it's possible that the interrupt status would
be incorrect at the end of the processing.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support");
CC: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: fc831825f9 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving an Rx LL2 packet, qed fails to unmap the previous buffer.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support");
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
