CDCLK is used to generate the gmbus clock. This is normally done by
BIOS. Program the value if the BIOS-less system doesn't do it.
v2: Move this to intel_i2c_reset to allow reprogram the gmbus frequency
during resume. (Daniel)
v3: Change GMBUS_FREQ to GMBUSFREQ_VLV, and use VLV_DISPLAY_BASE.
(Ville).
Remove cdclk_ratio[] table, and calculate the cdclk ratio instead.
(Ville).
Change the shift then mask for reg read, to mask first, then shift.
(Ville).
Remove the gmbus frequency calculation = cdclk/1.01. Based on BIOS
programming, gmbus frequency = cdclk frequency. (Ville)
Add get_disp_clk_div, which can use to get cdclk/czclk divide.
v4: Fix the mmio_offset base for CZCLK_CDCLK_FREQ_RATIO, gmbus_freq
calculation, and duplicate check for gmbus_freq. (Ville)
In VLV, the spec is wrong about 4Mhz reference frequency for GMBUS. It
should be 1Mhz.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[danvet: Add the comment Ville suggested. Also appease checkpatch a
bit.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The | operation has higher precedence than "?:" so the macro always
returns GT_RENDER_L3_PARITY_ERROR_INTERRUPT_S1.
This regression has been introduce in "drm/i915: Add second slice l3
remapping".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Future generations will be changing these registers (thanks to design
for giving us an early heads up). To help abstract, create the
definition of the base of the register block, and define all registers
relative to that.
Design has promised to not change the offsets relative to the base.
v2: Also change IS_HASWELL checks to HAS_PSR
CC: Rodrigo Vivi <rodrigo.vivi@gmail.com>
CC: Intel GFX <intel-gfx@lists.freedesktop.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Certain HSW SKUs have a second bank of L3. This L3 remapping has a
separate register set, and interrupt from the first "slice". A slice is
simply a term to define some subset of the GPU's l3 cache. This patch
implements both the interrupt handler, and ability to communicate with
userspace about this second slice.
v2: Remove redundant check about non-existent slice.
Change warning about interrupts of unknown slices to WARN_ON_ONCE
Handle the case where we get 2 slice interrupts concurrently, and switch
the tracking of interrupts to be non-destructive (all Ville)
Don't enable/mask the second slice parity interrupt for ivb/vlv (even
though all docs I can find claim it's rsvd) (Ville + Bryan)
Keep BYT excluded from L3 parity
v3: Fix the slice = ffs to be decremented by one (found by Ville). When
I initially did my testing on the series, I was using 1-based slice
counting, so this code was correct. Not sure why my simpler tests that
I've been running since then didn't pick it up sooner.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
You can't write it using the MCHBAR mirror, the write will just get
dropped.
This should make us BSpec-compliant, but there's no real bug I could
reproduce that is fixed by this patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Fix spelling mistake in the comment that Damien spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that adjusted_mode.clock no longer contains the pixel_multiplier, we
can kill the get_clock() callback and instead do the clock readout
in get_pipe_config().
Also i9xx_crtc_clock_get() can now extract the frequency of the PCH
DPLL, so use it to populate port_clock accurately for PCH encoders.
For DP in port A the encoder is still responsible for filling in
port_clock. The FDI adjusted_mode.clock extraction is kept in place
for some extra sanity checking, but we no longer need to pretend it's
also the port_clock.
In the encoder get_config() functions fill out adjusted_mode.clock
based on port_clock and other details such as the DP M/N values,
HDMI 12bpc and SDVO pixel_multiplier. For PCH encoders we will then
do an extra sanity check to make sure the dotclock we derived from
the FDI configuratiuon matches the one we derive from port_clock.
DVO doesn't exist on PCH platforms, so it doesn't need to anything
but assign adjusted_mode.clock=port_clock. And DDI is HSW only, so
none of the changes apply there.
v2: Use hdmi_reg color format to detect 12bpc HDMI case
v3: Set adjusted_mode.clock for LVDS too
v4: Rename ironlake_crtc_clock_get to ironlake_pch_clock_get,
eliminate the useless link_freq variable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove duplicates, add VLV specific macros for port B and C.
v2: also add PANEL_PORT_SELECT_DPC_VLV for clarity (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Batchbuffers constructed by userspace can conditionalise their URB
allocations through the use of the MI_SET_PREDICATE command. This
command can read the MI_PREDICATE_RESULT_2 register to see how many
slices are enabled on GT3, and by virtue of the result, scale their
memory allocations to fit enabled memory.
Of course, this only works if the kernel sets the appropriate bit in the
register first.
v2: Better commit subject and message by Chris Wilson.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Credits-to: Yejun Guo <yejun.guo@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2:
- Grab dpio_lock mutex in vlv_enable_dsi_pll().
- Add and call vlv_disable_dsi_pll().
v3: Mostly based on Ville's review comments.
- Only pipe A has DSI PLL lock bit.
- Add more of CCK REG bit definitions for DSI PLL.
- Make tables static.
- Move clock gating out of the clock calculation functions.
- DSI PLL LDO power gating.
- Put alternative MNP from table calc behind #ifdef.
v4: s/CKK/CLK/ in the CCK REG bit definitions (Ville).
Signed-off-by: ymohanma <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add definitions for VLV MIPI DSI registers.
v2: Small fixes per Ville's review comments.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Add comment this is pipe A only (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For GPIO NC, CCK, CCU, and GPS CORE.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We shouldn't disable the trickle feed bits on Haswell. Our
documentation explicitly says the trickle feed bits of PRI_CTL and
CUR_CTL should not be programmed to 1, and the hardware engineer also
asked us to not program the SPR_CTL field to 1. Leaving the bits as 1
could cause underflows.
Reported-by: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Systems with Intel graphics controllers set aside memory exclusively for
gfx driver use. This memory is not always marked in the E820 as
reserved or as RAM, and so is subject to overlap from E820 manipulation
later in the boot process. On some systems, MMIO space is allocated on
top, despite the efforts of the "RAM buffer" approach, which simply
rounds memory boundaries up to 64M to try to catch space that may decode
as RAM and so is not suitable for MMIO.
v2: use read_pci_config for 32 bit reads instead of adding a new one
(Chris)
add gen6 stolen size function (Chris)
v3: use a function pointer (Chris)
drop gen2 bits (Daniel)
v4: call e820_sanitize_map after adding the region
v5: fixup comments (Peter)
simplify loop (Chris)
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66726
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66844
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
RCS flips do work on Iybridge+ so long as we can unmask the messages
through DERRMR. However, there are quite a few workarounds mentioned
regarding unmasking more than one event or triggering more than one
message through DERRMR. Those workarounds in principle prevent us from
performing pipelined flips (and asynchronous flips across multiple
planes) and equally apply to the "known good" BCS ring. Given that it
already appears to work, and also appears to work with unmasking all 3
planes at once (and queuing flips across multiple planes), be brave.
Bugzlla: https://bugs.freedesktop.org/show_bug.cgi?id=67600
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Lightly-tested-by: Stephane Marchesin <marchesin@icps.u-strasbg.fr>
Cc: Stephane Marchesin <marchesin@icps.u-strasbg.fr>
Cc: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
Need to get my stuff out the door ;-) Highlights:
- pc8+ support from Paulo
- more vma patches from Ben.
- Kconfig option to enable preliminary support by default (Josh
Triplett)
- Optimized cpu cache flush handling and support for write-through caching
of display planes on Iris (Chris)
- rc6 tuning from Stéphane Marchesin for more stability
- VECS seqno wrap/semaphores fix (Ben)
- a pile of smaller cleanups and improvements all over
Note that I've ditched Ben's execbuf vma conversion for 3.12 since not yet
ready. But there's still other vma conversion stuff in here.
* tag 'drm-intel-next-2013-08-23' of git://people.freedesktop.org/~danvet/drm-intel: (62 commits)
drm/i915: Print seqnos as unsigned in debugfs
drm/i915: Fix context size calculation on SNB/IVB/VLV
drm/i915: Use POSTING_READ in lcpll code
drm/i915: enable Package C8+ by default
drm/i915: add i915.pc8_timeout function
drm/i915: add i915_pc8_status debugfs file
drm/i915: allow package C8+ states on Haswell (disabled)
drm/i915: fix SDEIMR assertion when disabling LCPLL
drm/i915: grab force_wake when restoring LCPLL
drm/i915: drop WaMbcDriverBootEnable workaround
drm/i915: Cleaning up the relocate entry function
drm/i915: merge HSW and SNB PM irq handlers
drm/i915: fix how we mask PMIMR when adding work to the queue
drm/i915: don't queue PM events we won't process
drm/i915: don't disable/reenable IVB error interrupts when not needed
drm/i915: add dev_priv->pm_irq_mask
drm/i915: don't update GEN6_PMIMR when it's not needed
drm/i915: wrap GEN6_PMIMR changes
drm/i915: wrap GTIMR changes
drm/i915: add the FCLK case to intel_ddi_get_cdclk_freq
...
With all the common infoframe bits now in place, we can finally write
the vendor specific infoframes in our driver.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Fix the typo introduced in
commit 1a2eb4604b
Author: Keith Packard <keithp@keithp.com>
Date: Wed Nov 16 16:26:07 2011 -0800
drm/i915: Hook up Ivybridge eDP
This fixes eDP link-training failures and cases where all voltage swing
/pre-emphasis levels were tried and failed during clock recovery and -
as a fallback - we go on to do channel equalization with the last voltage
swing/pre-emphasis level which will succeed. Both issues can lead to a
blank screen.
v2:
- improve commit message
CC: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64880
Tested-by: Jeremy Moles <cubicool@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the different context sizes reported in the CXT_SIZE register
aren't meant to be simply added together.
While BSpec is somewhat unclear on the topic of the actual context
size, empirical tests have now revealed the truth. So let's add a
big fat comment to remind people how it all works.
As a result of correctly interpreting CXT_SIZE, the IVB context
size is reduced from three pages to two, while SNB context size
remains at two pages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SNB and IVB, there's an MSR (also exposed through MCHBAR) we can use
to read out the amount of energy used over time. Expose this in sysfs
to make it easy to do power comparisons with different configurations.
If the platform supports it, the file will show up under the
drm/card0/power subdirectory of the PCI device in sysfs as gt_energy_uJ.
The value in the file is a running total of energy (in microjoules)
consumed by the graphics device.
v2: move to sysfs (Ben, Daniel)
expose a simple value (Chris)
drop unrelated hunk (Ben)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
v3: by Ben
Tied it into existing rc6 sysfs entries and named that a more generic
"power attrs." Fixed rebase conflicts.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
v4: Since RAPL is a real driver that already exists to serve power
monitoring, place our entry in debugfs. This gives me a fallback
location for systems that do not expose it otherwise.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whenever I need to work with the HSW_PWER_WELL_* register bits I have
to look at the documentation to find out which bit is to request the
power well and which one shows its current state. Rename the bits so I
won't need to look the docs every time.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After any "soft gfx reset" we must manually invalidate the TLBs
associated with each ring. Empirically, it seems that a
suspend/resume or D3-D0 cycle count as a "soft reset". The symptom is
that the hardware would fail to note the new address for its status
page, and so it would continue to write the shadow registers and
breadcrumbs into the old physical address (now used by something
completely different, scary). Whereas the driver would read the new
status page and never see any progress, it would appear that the GPU
hung immediately upon resume.
Based on a patch by naresh kumar kachhi <naresh.kumar.kacchi@intel.com>
Reported-by: Thiago Macieira <thiago@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64725
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Thiago Macieira <thiago@kde.org>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently Bspec is wrong in this case here even for gm45. Note that
Bspec is horribly misguided on i965g/gm, so we don't have any other
data points besides that it seems to make machines work better.
With this changes all the bits in PORT_HOTPLUG_STAT for the digital
ports are ordered the same way. This seems to agree with what register
dumps from the hpd storm handling code shows, where the LIVE bit and
the short/long pulse STATUS bits light up at the same time with this
enumeration (but no with the one from Bspec).
Also tested on my gm45 which has two DP+ ports, and everything seems
to still work as expected.
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg23054.html
Cc: Egbert Eich <eich@suse.com>
Cc: Jan Niggemann <jn@hz6.de>
Tested-by: Jan Niggemann <jn@hz6.de>
[danvet: Add a big warning that Bspec seems to be wrong for these
bits, suggested by Jani.]
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adjust the current ILK/SNB/IVB watermark codepaths to use the
pre-populated latency values from dev_priv instead of reading
them out from the registers every time.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need the correct clock to accurately assess whether we need to
enable the double wide pipe mode or not.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Stuart Abercrombie <sabercrombie@google.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For now there are no callers, but these functions are going to be
needed for the code that allows Package C8+. Other future features may
also require this code.
Also merge the commit which introduced assert_can_disable_lcpll and
had the following commit message:
Most of the hardware needs to be disabled before LCPLL is disabled, so
let's add a function to assert some of items listed in the "Display
Sequences for LCPLL disabling" documentation.
The idea is that hsw_disable_lcpll should not disable the hardware,
the callers need to take care of calling hsw_disable_lcpll only once
everything is already disabled.
v2: - Rebase.
- Fix D_COMP wait timeout.
v3: - Use wait_for_atomic_use (Ben)
- Remove/add a useless/needed POSTING_READ (Ben)
- Early return in case LCPLL is already restored (Ben)
- Add ndelay(100) (Ben)
v4: - Merge the commit that added assert_can_disable_lcpll (Ben)
- Add interrupt assertions (Ben)
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix compile fail since there's no HAS_LP_PCH yet.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now it implements 3 different sequences from BSpec and also has
support for ULT.
v2: - Change IS_ULT checks for LPT-LP checks
- Add check for LPT-LP + with_fdi (Ben)
- Merge DBUFF0/GEN0 bit definitions since they're the same
register (Ben)
- DBUFF0 (1<<0) is Disable, not Enable
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The IVB funtions are exactly the same as the ILK ones, with the
exception of the bit register. So add IVB/HSW support to
ironlake_enable_vblank and ironlake_disable_vblank, then kill the
ivybridge functions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Prefer seq_puts to seq_printf by Paulo Zanoni.
v3: small changes like avoiding calling dp_to_dig_port twice as noticed by
Paulo Zanoni.
v4: Avoiding reading non-existent registers - noticed by Paulo
on first psr debugfs patch.
v5: Accepting more suggestions from Paulo:
* check sw interlace flag instead of i915_read
* introduce PSR_S3D_ENABLED to avoid forgeting it whenever added.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Fix up debugfs output (spotted by Paulo) and rip out the
power well check since we really can't do that in a race-free manner,
so it's bogus.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding support for PSR Status, PSR entry counter and performance counters.
Heavily based on initial work from Shobhit.
v2: Fix PSR Status Link bits by Paulo Zanoni.
v3: Prefer seq_puts to seq_printf by Paulo Zanoni.
v4: Fix identation by Paulo Zanoni.
v5: Return earlier if it isn't Haswell in order to avoid reading non-existing
registers - by Paulo Zanoni.
CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Credits-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding Enable and Disable PSR functionalities. This includes setting the
PSR configuration over AUX, sending SDP VSC DIP over the eDP PIPE config,
enabling PSR in the sink via DPCD register and finally enabling PSR on
the host.
This patch is based on initial PSR code by Sateesh Kavuri and Kumar Shobhit
but in a different implementation.
v2: * moved functions around and changed its names.
* removed VSC DIP unset from disable.
* remove FBC wa.
* don't mask LSPS anymore.
* incorporate new crtc usage after a rebase.
v3: Make a clear separation between Sink (Panel) and Source (HW) enabling.
v4: Fix identation and other style issues raised by checkpatch (by Paulo).
v5: Changes according to Paulo's review:
static on write_vsc;
avoid using dp_to_dev when already calling dp_to_dig_port;
remove unecessary TP default time setting;
remove unecessary interrupts disabling;
remove unecessary wait_for_vblank when disabling psr;
v6: remove unecessary wait_for_vblank when writing vsc;
v7: adding setup once function to avoid unnecessarily write to vsc
and set debug_ctl every time we enable or disable psr.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Credits-by: Sateesh Kavuri <sateesh.kavuri@intel.com>
Credits-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Apply Paulo's suggestion for unconditionally clearing the
control register when writing the DIP.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The EDRAM present register isn't really defined in the docs. It just
says check to see if it's set to 1. So I haven't defined the 1 value not
knowing what it actually means.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same treatment as for SERR_INT: If we clear only the bit for the pipe
we're enabling (but unconditionally) then we can always check for
possible underruns after having disabled the interrupt. That way pipe
underruns won't be lost, but at worst only get reported in a delayed
fashion.
v2: The same logic bug as in the SERR handling change also existed
here. The same bugfix of only reporting missed underruns when the
error interrupt was masked applies, too.
v3: Do the same fixes as for the SERR handling that Paulo suggested in
his review:
- s/%i/%c/ fix in the debug output
- move the DE_ERR_INT_IVB read into the respective if block
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix up the checkpatch bikeshed Paulo noticed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current code won't report any fifo underruns on cpt if just one
pipe has fifo underrun reporting disabled. We can't enable the
interrupts, but we can still check the per-transcoder bits and so
report the underrun delayed if:
- We always clear the transcoder's bit (and none of the other bits)
when enabling.
- We check the transcoder's bit after disabling (to avoid racing with
the interrupt handler).
v2: I've forgotten to actually remove the old SERR_INT clearing.
v3: Use transcoder_name as suggested by Paulo Zanoni. Paulo also
noticed a logic bug: When an underrun interrupt fires we report it
both in the interrupt handler and when checking for underruns when
disabling it in cpt_set_fifo_underrun_reporting. But that second check
is only required if the interrupt is disabled and we're switching of
underrun reporting (e.g. because we're disabling the crtc). Hence
check for that condition.
At first I wanted to rework the code to pass that bit of information
from the uppper functions down to cpt_set_fifo_underrun_reporting. But
that turned out too messy. Hence the quick&dirty check whether the
south error interrupt source is masked off or not.
v4: Streamline the control flow a bit.
v5: s/pipe/pch transcoder/ in the dmesg output, suggested by Paulo.
v6: Review from Paulo:
- Reorder the was_enabled assignment to only read the register when we
need it. Also add a comment that we need to do that before updating
the register.
- s/%i/%c/ fix for the debug output.
- Fix the checkpath complaint in the SERR_INT_TRANS_FIFO_UNDERRUN
#define.
v7: Hopefully put that elusive SERR hunk back into this patch, spotted
by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've missed that intel_dvo_mode_set changes the dpll configuration.
Hence when I've reworked the sequence to only enable the dpll in the
crtc_enable callback in
commit 66e3d5c099
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jun 16 21:24:16 2013 +0200
drm/i915: move i9xx dpll enabling into crtc enable function
that special DVO bit was lost. Some BSpec reading confirms that it's
only needed for DVO encoders. Section 1.5.4, "DPLL A Control Register"
for bit 30:
"2X Clock Enable. When driving In non-gang DVO modes such as a
connected flat panel or TV, a 2X" version of the clock is needed. When
not using the 2X output it should be disabled. This bit cannot be set
when driving the integrated LVDS port on devices such as Montara-GM."
Fix this regression up.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66516
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Partially-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use wait_for() instead of the open coded loop to avoid spreading the
same old timeout related bugs.
This changes the loop to use msleep(1) instead of udelay(10) when the
Punit had not yet completed the frequency change. In practice that
doesn't seem to hurt performance as the Punit appears to be ready pretty
much always.
Also give the status bit a name, instead of using the magic number 1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With updates to the spec, we can actually see the context layout, and
how many dwords are allocated. That table suggests we need 70720 bytes
per HW context. Rounded up, this is 18 pages. Looking at what lives
after the current 4 pages we use, I can't see too much important (mostly
it's d3d related), but there are a couple of things which look scary. I
am hopeful this can explain some of our odd HSW failures.
v2: Make the context only 17 pages. The power context space isn't used
ever, and execlists aren't used in our driver, making the actual total
66944 bytes.
v3: Add a comment to the code. (Jesse & Paulo)
Reported-by: "Azad, Vinit" <vinit.azad@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We forgot to add VLV_DISPLAY_BASE to the VLV sprite registers, which
caused the sprites to not work at all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
LPF is short for "low pass filter".
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec seems to be full of lies, at least it disagress with reality:
Two systems corrobated that SDVO hpd bits are the same as on gen3.
v2: Update comment a bit.
Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Alex Fiestas <afiestas@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58405
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again we don't really support different settings, so don't let the
BIOS sneak stuff through.
Since the motivation for this patch series is to ensure we have the
correct gamma table mode selected also add the required write to the
GAMMA_MODE register to select the 8bit legacy table.
And since I find lowercase letters in #defines offensive, also
bikeshed those.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The specs are a bit unclear whether the per-plane trickle feed disable
control exists on VLV. There is another trickle feed disable control
in the MI_ARB register.
After some experimentation it turns out both the DSPCNTR trickle feed
bits and the MI_ARB bit can be toggled. However the DSPCNTR bits don't
seem to have any effect.
The MI_ARB bit, on the other hand, has a noticable effect. I performed
an experiment where I reduced the FIFO size via DSPARB and observed the
effect of the MI_ARB trickle feed bit on the display.
Using a 1920x1080-60 mode, with MI_ARB=0x4 the display started to have
problems with DSPARB=0x42424242, whereas with MI_ARB=0x0 the problems
didn't start until DSPARB=0x09090909. This seems to confirm that the
MI_ARB trickle feed bit actually does work.
So replace the use of the DSPCNTR trickle feed bits with MI_ARB
on VLV.
v2: Amend commit message with results from experimentation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Using ids in register macros is much more common in our driver. Also
this way we can reduce the platform specific stuff a bit.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bits are evenly space, so we can cut down on two big switch
blocks. This also greatly simplifies the hw state readout which
follows in the next patch.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaFbcNukeOn3DBlt for IVB, HSW.
According BSPec: "Workaround: Do not enable Render Command Streamer tracking for FBC.
Instead insert a LRI to address 0x50380 with data 0x00000004 after the PIPE_CONTROL that
follows each render submission."
v2: Chris noticed that flush_domains check was missing here and also suggested to do
LRI only when fbc is enabled. To avoid do a I915_READ on every flush lets use the
module parameter check.
v3: Adding Wa name as Damien suggested.
v4: Ville noticed VLV doesn't support fbc at all and comment came wrong from spec.
v5: Ville noticed than on blt a Cache Clean LRI should be used instead the Nuke one.
v6: Check for flush domain on blt (by Ville).
Check for scanout dirty (by Chris).
v7: Apply proper fbc_dirty implemented by Chris.
v8: remove unused variables.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use port I/O for VGA register access, so adding display_mmio_offset
is just wrong.
This reverts commit 56a12a5092.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the DSPCLK_GATE_D access for VLV. The code incorrectly tried to
poke at the ILK+ version of the register which is at the wrong offset.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Intermediate Pixel Storage is a feature that should reduce the number
of times the display engine wakes up memory to read pixels, so it
should allow deeper PC states. IPS can only be enabled on ULT pipe A
with 8:8:8 pipe pixel formats.
With eDP 1920x1080 and correct watermarks but without FBC this moves
my PC7 residency from 2.5% to around 38%.
v2: - It's tied to pipe A, not port A
- Add pipe_config support (Chris)
- Add some assertions (Chris)
- Rebase against latest dinq
v3: - Don't ever set ips_enabled to false (Daniel)
- Only check for ips_enabled at hsw_disable_ips (Daniel)
v4: - Add hsw_compute_ips_config (Daniel)
- Use the new dump_pipe_config (Daniel)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to a patch originally written by:
v2: Reversed the meanings of masked and enabled (Haihao)
Made non-destructive writes in case enable/disabler rps runs first
(Haihao)
v3: Reword error message (Damien)
Modify postinstall to do the right thing based on previous fixup. (Ben)
CC: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
