The function signature of does not match regulator_get_error_flags()
when CONFIG_REGULATOR is not defined vs. when it is not defined.
This makes both declarations match to prevent compiler errors.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator consumers can receive event notifications when
errors are reported to the driver, but currently, there is
no way for a regulator consumer to know when the error is over.
To allow a regulator consumer to poll for error conditions
add a new API: regulator_get_error_flags.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new op is analogous to set_voltage_time_sel. It can be used by
regulators which don't have a table of discrete voltages. The function
returns the time for the regulator output voltage to stabilize after
being set to a new value, in microseconds. If the op is not set a
default implementation is used to calculate the delay.
This change also removes the ramp_delay calculation in the PWM
regulator, since the driver now uses the core code for the calculation
of the delay.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch was based on my missinterpretation of the API and only
accidentally worked for me. Let's clean it out to not confuse others.
This reverts commit 3ff3f518a1.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MT6323 is a regulator found on boards based on MediaTek MT7623 and
probably other SoCs. It is a so called pmic and connects as a slave to
SoC using SPI, wrapped inside the pmic-wrapper.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a patch for adding description for da9212/da9214.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is little obvious use case for a regualtor driver to know if it is
possible to vary voltages at all by itself. If a consumer needs to
limit what voltages it tries to set based on the system configuration
then it will need to enumerate the possible voltages, and without that
even if it is possible to change voltages that doesn't mean that
constraints or other consumers will allow whatever change the driver is
trying to do at a given time. It doesn't even indicate if _set_voltage()
calls will work as noop _set_voltage() calls return success.
There were no users of this API that weren't abusing it and now they're
all gone so remove the API.
Signed-off-by: Mark Brown <broonie@kernel.org>
Cut down on noise for mainstream users of the API and people doing build
testing by dropping the deprecated flag from regulator_can_change_voltage()
as it triggers even on the EXPORT_SYMBOL_GPL() which affects all builds
rather than just the remaining drivers with calls to it (for which fixes
are currently pending).
The function remains deprecated and is expected to be removed entirely
in v4.8.
Signed-off-by: Mark Brown <broonie@kernel.org>
Using a bitfield enables the compiler to lay out the structure more
efficiently when we have other boolean flags since multiple values can
be included in a single byte.
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver MAX8973 supports the driver for Maxim PMIC MAX77621.
MAX77621 supports the junction temp warning at 120 degC and
140 degC which is configurable. It generates alert signal when
junction temperature crosses these threshold.
MAX77621 does not support the continuous temp monitoring of
junction temperature. It just report whether junction temperature
crossed the threshold or not.
Add support to
- Configure junction temp warning threshold via DT property
to generate alert when it crosses the threshold.
- Add support to interrupt the host from this device when alert
occurred.
- read the junction temp via thermal framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All current users of regulator_can_change_voltage() are abusing it,
using it to wrap a call to regulator_set_voltage() on probe without any
alternative handling for fixed voltages. Drivers should only be using
regulator_set_voltage() if they need to vary voltages at runtime, fixed
voltages should normally be set via machine constraints, and calling
regulator_set_voltage() on a regulator which can't be varied will
succeed if the current voltage is within the range requested so users
shouldn't worry if they have permission to vary normally.
Deprecate the API to try to stop any new users appearing while we fix
the current callers.
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes the code easier to read and it avoids a dynamic memory
allocation.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Over current protection is missing descriptions for documentation.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Members csel_reg and csel_mask of the regulator_desc struct are missing
descriptions for documentation. Adding them.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper function to set the state of active-discharge of
regulator using regmap. The HW regulator driver can directly
use this by providing the necessary information in the regulator
descriptor.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to enable/disable active discharge of regulator via
machine constraints. This configuration is done when setting
machine constraint during regulator register and if regulator
driver implemented the callback ops.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LP872x regulators are made active via the EN pin, which might be hooked to a
GPIO. This adds support for driving the GPIO high when the driver is in use.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for TPS65218 LS3 current regulator, which is capable of 4
current input limit modes: 100, 200, 500, and 1000 uA.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it possible to use the bulk API with optional supplies, by allowing
the consumer to marking supplies as optional in the regulator_bulk_data.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many voltage Regulators need a input voltage that is higher than the
output voltage. Allow to specify a minimum dropout voltage which will
be used later to find the best input voltage for regulators.
[Changed uv to uV for consistency and legibility -- broonie]
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Voltage tolerance isn't necessarily same on both sides of the target
voltage and regulator_set_voltage_tol() wouldn't be suitable in such
cases.
Add another routine regulator_set_voltage_triplet(), which accepts
target, min and max voltages as arguments.
This first tries to set the voltage between the target voltage and the
upper limit, then fall back on the full range. The idea behind this is
to set regulator's voltage as close to the target voltage, as possible.
Based on regulator_set_voltage_tol().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators can automatically shut down when they detect an
over current event. Add an op (set_over_current_protection) and a
DT property + constraint to support this capability.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator support for mt6311.
It has 2 regulaotrs - Buck and LDO, provide the related buck/ldo voltage
data to the driver, and creates the regulator_desc table. Supported
operations for Buck are enabled/disabled and voltage change, only
enabled/disabled for LDO.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a patch for supporting da9215 buck converter.
Signed-off-by: James Ban <james.ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes a build break when CONFIG_REGULATOR is not selected.
e.g, on linux-next - 07102015:
drivers/clk/tegra/clk-dfll.c: In function ‘find_lut_index_for_rate’:
drivers/clk/tegra/clk-dfll.c:691:3: error: implicit declaration of function ‘regulator_list_voltage’ [-Werror=implicit-function-declaration]
if (regulator_list_voltage(td->vdd_reg, td->i2c_lut[i]) == uv)
^
CC drivers/clocksource/mmio.o
CC fs/proc/softirqs.o
cc1: some warnings being treated as errors
make[3]: *** [drivers/clk/tegra/clk-dfll.o] Error 1
make[2]: *** [drivers/clk/tegra] Error 2
make[1]: *** [drivers/clk] Error 2
make[1]: *** Waiting for unfinished jobs....
This should be pushed to 4.2 as we have the issue in 4.2-rc1, just that
nobody uses it without the REGULATOR(yet).
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The docbook for these members is missing. Add them.
Warning(include/linux/regulator/machine.h:147): No description
found for parameter 'soft_start'
Warning(include/linux/regulator/driver.h:197): No description
found for parameter 'set_soft_start'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators can limit their input current (typically annotated
as ilim). Add an op (set_input_current_limit) and a DT property +
constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators support a "soft start" feature where the voltage
ramps up slowly when the regulator is enabled. Add an op
(set_soft_start) and a DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators need to be configured to pull down a resistor
when the regulator is disabled. Add an op (set_pull_down) and a
DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators have a fixed load that isn't captured by
consumers that the kernel knows about. Add a constraint to
support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
MAX8973 supports the voltage output enable/disable through its EN
pin. This EN pin can be connected through GPIO from host processor.
Add support to provide GPIO number from platform/DT and if it is
valid GPIO then enable external control default.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of resolving regulator supplies during registration move this to
the time of a consumer retrieving a handle. The benefit is that it's
possible for one driver to register regulators with internal
dependencies out of order.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
