The trans cfg was not replaced for 7265-D cards. This led to a check of
the min-NVM version against a 7265-C card, causing very-old 7265-D cards
to operate incorrectly with the driver.
Fixes: 3fd0d3c170 ("iwlwifi: pcie: support 7265-D devices")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These drivers use 9100-byte receive buffers, thus allocating an skb requires
an O(3) memory allocation. Under heavy memory loads and fragmentation, such
a request can fail. Previous versions of the driver have dropped the packet
and reused the old buffer; however, the new version introduced a bug in that
it released the old buffer before trying to allocate a new one. The previous
method is implemented here. The skb is unmapped before any attempt is made to
allocate another.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [v3.18]
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Cc: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The CPSW IP implements pulse-signaled interrupts. Due to
that we must write a correct, pre-defined value to the
CPDMA_MACEOIVECTOR register so the controller generates
a pulse on the correct IRQ line to signal the End Of
Interrupt.
The way the driver is written today, all four IRQ lines
are requested using the same IRQ handler and, because of
that, we could fall into situations where a TX IRQ fires
but we tell the controller that we ended an RX IRQ (or
vice-versa). This situation triggers an IRQ storm on the
reserved IRQ 127 of INTC which will in turn call ack_bad_irq()
which will, then, print a ton of:
unexpected IRQ trap at vector 00
In order to fix the problem, we are moving all calls to
cpdma_ctlr_eoi() inside the IRQ handler and making sure
we *always* write the correct value to the CPDMA_MACEOIVECTOR
register. Note that the algorithm assumes that IRQ numbers and
value-to-be-written-to-EOI are proportional, meaning that a
write of value 0 would trigger an EOI pulse for the RX_THRESHOLD
Interrupt and that's the IRQ number sitting in the 0-th index
of our irqs_table array.
This, however, is safe at least for current implementations of
CPSW so we will refrain from making the check smarter (and, as
a side-effect, slower) until we actually have a platform where
IRQ lines are swapped.
This patch has been tested for several days with AM335x- and
AM437x-based platforms. AM57x was left out because there are
still pending patches to enable ethernet in mainline for that
platform. A read of the TRM confirms the statement on previous
paragraph.
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Fixes: 510a1e7 (drivers: net: davinci_cpdma: acknowledge interrupt properly)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull UML fixes from Richard Weinberger:
"Two fixes for UML regressions. Nothing exciting"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
x86, um: actually mark system call tables readonly
um: Skip futex_atomic_cmpxchg_inatomic() test
Commit a074335a37 ("x86, um: Mark system call tables readonly") was
supposed to mark the sys_call_table in UML as RO by adding the const,
but it doesn't have the desired effect as it's nevertheless being placed
into the data section since __cacheline_aligned enforces sys_call_table
being placed into .data..cacheline_aligned instead. We need to use
the ____cacheline_aligned version instead to fix this issue.
Before:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev
0000000000000000 D sys_call_table
0000000000000000 D syscall_table_size
After:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev
0000000000000000 R sys_call_table
0000000000000000 D syscall_table_size
Fixes: a074335a37 ("x86, um: Mark system call tables readonly")
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
futex_atomic_cmpxchg_inatomic() does not work on UML because
it triggers a copy_from_user() in kernel context.
On UML copy_from_user() can only be used if the kernel was called
by a real user space process such that UML can use ptrace()
to fetch the value.
Reported-by: Miklos Szeredi <miklos@szeredi.hu>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Daniel Walter <d.walter@0x90.at>
When allocation of all RQs fail, we do not free previously allocated buffers,
before returning error. This causes memory leak.
This patch fixes this by calling vnic_rq_clean(), which frees all the rq
buffers.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some buggy firmwares export an incorrect MAC address (00:a0:c6:00:00:00). This
makes for example checking devices for random MAC addresses tricky, and you
might end up with multiple network interfaces with the same address.
This patch tries to fix, or at least improve, the situation by setting the MAC
address of devices with this firmware bug to a random address. I tested the
patch with two devices that has this firmware bug (Huawei E398 and E392), and
network traffic worked fine after changing the address.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a set of three fixes: one to correct an abort path thinko causing
failures (and a panic) in USB on device misbehaviour, One to fix an out of
order issue in the fnic driver and one to match discard expectations to qemu
which otherwise cause Linux to behave badly as a guest.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJUpsmHAAoJEDeqqVYsXL0MdToH/1UsmOdtxNh6AfBDWWYi45o8
kBno1gTnRrDgIlOiRu+BtmL25A1rNcCdCQKjG6JBEBruqUVAwZztktGjfuSvso6s
EYbrnE+5DmDs6cW8pp6GK3QGV+R+AmbT8oBbe/Kpg5LdTsdnQOozSycUp7X3XgTi
pLOm6rW/AgEV1QFcQz1bjI6cnbcOZMcGZnC5qwphiKgBnVYd+PZY24RSHDKCu/va
z2lsa5yqXFHKZZZRhYG343YqCTf3Dkph78124JoNvVm3EjO+GQAAiojiUa7l59UF
RqNRqeMxfz2cPmBnJxbNmWiP1YQGBgOaNDRgc7D7SPxaMwUe9444Gm4MkoZWzmQ=
=706l
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of three fixes: one to correct an abort path thinko
causing failures (and a panic) in USB on device misbehaviour, One to
fix an out of order issue in the fnic driver and one to match discard
expectations to qemu which otherwise cause Linux to behave badly as a
guest"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
SCSI: fix regression in scsi_send_eh_cmnd()
fnic: IOMMU Fault occurs when IO and abort IO is out of order
sd: tweak discard heuristics to work around QEMU SCSI issue
Until now, when VLAN acceleration was in use, the bytes of the VLAN header
were not included in port or flow byte counters. They were however
included when VLAN acceleration was not used. This commit corrects the
inconsistency, by always including the VLAN header in byte counters.
Previous discussion at
http://openvswitch.org/pipermail/dev/2014-December/049521.html
Reported-by: Motonori Shindo <mshindo@vmware.com>
Signed-off-by: Ben Pfaff <blp@nicira.com>
Reviewed-by: Flavio Leitner <fbl@sysclose.org>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Jarosch reported IPsec TCP stalls when a PMTU event occurs.
In fact the problem was completely unrelated to IPsec. The bug is
also reproducible if you just disable TSO/GSO.
The problem is that when the MSS goes down, existing queued packet
on the TX queue that have not been transmitted yet all look like
TSO packets and get treated as such.
This then triggers a bug where tcp_mss_split_point tells us to
generate a zero-sized packet on the TX queue. Once that happens
we're screwed because the zero-sized packet can never be removed
by ACKs.
Fixes: 1485348d24 ("tcp: Apply device TSO segment limit earlier")
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing too exciting as a new year's start here: most of fixes are for
ASoC, a boot crash fix on OMAP for deferred probe, a few driver
specific fixes (Intel, dwc, rockchip, rt5677), in addition to typo
fixes in kerneldoc comments for PCM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ARQX
-----END PGP SIGNATURE-----
Merge tag 'sound-3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Nothing too exciting as a new year's start here: most of fixes are for
ASoC, a boot crash fix on OMAP for deferred probe, a few driver
specific fixes (Intel, dwc, rockchip, rt5677), in addition to typo
fixes in kerneldoc comments for PCM"
* tag 'sound-3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Fix kerneldoc for params_*() functions
ASoC: rockchip: i2s: fix maxburst of dma data to 4
ASoC: rockchip: i2s: fix error defination of transmit data level
ASoC: Intel: correct the fixed free block allocation
ASoC: rt5677: fixed rt5677_dsp_vad_put rt5677_dsp_vad_get panic
ASoC: Intel: Fix BYTCR machine driver MODULE_ALIAS
ASoC: Intel: Fix BYTCR firmware name
ASoC: dwc: Iterate over all channels
ASoC: dwc: Ensure FIFOs are flushed to prevent channel swap
ASoC: Intel: Add I2C dependency to two new machines
ASoC: dapm: Remove snd_soc_of_parse_audio_routing() due to deferred probe
Altera network device doesn't come up after
ifconfig eth0 down
ifconfig eth0 up
The reason behind is clearing priv->phydev during tse_shutdown().
The phydev is not restored back at tse_open().
Resubmiting as to follow Tobias Klauser suggestion.
phy_start/phy_stop are called on each ifup/ifdown and
phy_disconnect is called once during the module removal.
Signed-off-by: Kostya Belezko <bkostya@hotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
mlx4 driver fixes for 3.19-rc2
Please push Maor's patch to -stable >= 3.17
Jack's fixes error-flow issues introduced in 3.19-rc1, no need for -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't call UNMAP_FA here, this is done in mlx4_load_one.
If mlx4_query_func fails, we need to invoke CLOSE_HCA for both
native and master.
Fixes: a0eacca948 ('net/mlx4_core: Refactor mlx4_load_one')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, mlx4_mt_rereg_write filled the MPT's entity_size with the
old MTT's page shift, which could result in using an incorrect offset.
Fix the initialization to be after we calculate the new MTT offset.
In addition, assign mtt order to -1 after calling mlx4_mtt_cleanup. This
is necessary in order to mark the MTT as invalid and avoid freeing it later.
Fixes: e630664 ('mlx4_core: Add helper functions to support MR re-registration')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 14516bb7bb.
This was causing regression test failures with generic/285 with an ext3
filesystem using CONFIG_EXT4_USE_FOR_EXT23.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
There's a single change here, fixing a vhost bug where vhost initialization
fails due to used ring alignment check being too strict.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUoRcnAAoJECgfDbjSjVRpb7IIAIGoNJkB56Q3WWX0rP5i1Lqi
Uxt8lrvySotzoWMVZlm2pGRiwJv2T1dQXKWetvZDn0GuwCBi2/vm2l4eOhu1K+VV
jOtKk8n8kDJVgMOGaJUwqt8lhDbqGwHHDUCKDk78/pV5Q959bAVo143vWOh2DixQ
m3YmvmLwyhF6CYNwOD0HqllaojDPBAP3k22GdmJNy/H7CpcOSYK7BRoiQHX7FsbR
I3Kj/7gf5OlZFzLTLxNx/O01p1BkX6EusADfl3+tl6nggc6vqW9fHNz/TZLGh9I/
ap0Ng3pm8q/t6S6wsPj8wzTHNesK4gVWvecRN8kZV8UQY2rwd/y7R/k+VpJDseg=
=+Pmi
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull vhost cleanup and virtio bugfix
"There's a single change here, fixing a vhost bug where vhost
initialization fails due to used ring alignment check being too
strict"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: relax used address alignment
virtio_ring: document alignment requirements
If the check of adapter fails and goes into the 'else' branch, the
return value 'err' should not still be zero.
Signed-off-by: Yongjian Xu <xuyongjiande@gmail.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
The patch also modifies the test of mgp->cmd to satisfy checkpatch.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-12-31
This series contains updates to fixes for e100, igb and i40e.
John Linville fixes a typo in e100 that has been around for some time,
where an attempted revert actually inverted the test for eeprom_mdix_enabled.
Todd fixes up a code comment that should have been removed back in 2007.
Joe Perches fixes a possible memory leak in i40e which was reported by
Dan Carpenter using smatch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I didn't notice that return in the code, fix it by
adding a goto out instead to free the memory.
Fixes:
> New smatch warnings:
> drivers/net/ethernet/intel/i40e/i40e_debugfs.c:832 i40e_dbg_dump_desc() warn: possible memory leak of 'ring'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull audit fix from Paul Moore:
"One audit patch to resolve a panic/oops when recording filenames in
the audit log, see the mail archive link below.
The fix isn't as nice as I would like, as it involves an allocate/copy
of the filename, but it solves the problem and the overhead should
only affect users who have configured audit rules involving file
names.
We'll revisit this issue with future kernels in an attempt to make
this suck less, but in the meantime I think this fix should go into
the next release of v3.19-rcX.
[ https://marc.info/?t=141986927600001&r=1&w=2 ]"
* 'upstream' of git://git.infradead.org/users/pcmoore/audit:
audit: create private file name copies when auditing inodes
Remove a FIXME comment that was missed in a commit on 1/2007.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Reported-by: nick <xerofoify@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Although it doesn't explicitly say so, commit 60ffa47875 ("e100:
Fix MDIO/MDIO-X") appears to be intended to revert the earlier commit
648951451e ("e100: fixed e100 MDI/MDI-X issues"). However,
careful examination reveals that the attempted revert actually
_inverted_ the test for eeprom_mdix_enabled. That is bound to program
a few PHYs incorrectly...
https://bugzilla.redhat.com/show_bug.cgi?id=1156417
Signed-off-by: "John W. Linville" <linville@tuxdriver.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull crypto fix from Herbert Xu:
"Fix a use-after-free crash in the user-space crypto API"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: af_alg - fix backlog handling
Follow aa0d532605 ("ia64: Use preempt_schedule_irq") and use
preempt_schedule_irq instead of enabling/disabling interrupts and
messing around with PREEMPT_ACTIVE in the nios2 low-level preemption
code ourselves. Also get rid of the now needless re-check for
TIF_NEED_RESCHED, preempt_schedule_irq will already take care of
rescheduling.
This also fixes the following build error when building with
CONFIG_PREEMPT:
arch/nios2/kernel/built-in.o: In function `need_resched':
arch/nios2/kernel/entry.S:374: undefined reference to `PREEMPT_ACTIVE'
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Ley Foon Tan <lftan@altera.com>
This patch initializes the mmu field of the cpuinfo structure to the
value supplied by the devicetree.
Signed-off-by: Walter Goossens <waltergoossens@home.nl>
Acked-by: Ley Foon Tan <lftan@altera.com>
A very small set of fixes for 3.19, as everyone was out. The clocksource
patch was something I missed for the merge window after the change that
broke arm64 was merged through arm-soc. The other two patches are
a fix for an undetected merge problem in mvebu and a defconfig change
to make some exynos boards work with the normal multi_v7_defconfig.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JNdC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A very small set of fixes for 3.19, as everyone was out.
The clocksource patch was something I missed for the merge window
after the change that broke arm64 was merged through arm-soc. The
other two patches are a fix for an undetected merge problem in mvebu
and a defconfig change to make some exynos boards work with the normal
multi_v7_defconfig"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
Add USB_EHCI_EXYNOS to multi_v7_defconfig
ARM: mvebu: Fix pinctrl configuration for Armada 370 DB
clocksource: arch_timer: Only use the virtual counter (CNTVCT) on arm64
Pull input layer fixes from Dmitry Torokhov:
"Fixes for v7 protocol for ALPS devices and few other driver fixes.
Also users can request input events to be stamped with boot time
timestamps, in addition to real and monotonic timestamps"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: hil_kbd - fix incorrect use of init_completion
Input: alps - v7: document the v7 touchpad packet protocol
Input: alps - v7: fix finger counting for > 2 fingers on clickpads
Input: alps - v7: sometimes a single touch is reported in mt[1]
Input: alps - v7: ignore new packets
Input: evdev - add CLOCK_BOOTTIME support
Input: psmouse - expose drift duration for IBM trackpoints
Input: stmpe - bias keypad columns properly
Input: stmpe - enforce device tree only mode
mfd: stmpe: add pull up/down register offsets for STMPE
Input: optimize events_per_packet count calculation
Input: edt-ft5x06 - fixed a macro coding style issue
Input: gpio_keys - replace timer and workqueue with delayed workqueue
Input: gpio_keys - allow separating gpio and irq in device tree
This reverts commit 24a0aa212e.
It's causing severe userspace breakage. Namely, all the utilities from
wireless-utils which are relying on CONFIG_WEXT (which means tools like
'iwconfig', 'iwlist', etc) are not working anymore. There is a 'iw'
utility in newer wireless-tools, which is supposed to be a replacement
for all the "deprecated" binaries, but it's far away from being
massively adopted.
Please see [1] for example of the userspace breakage this is causing.
In addition to that, Larry Finger reports [2] that this patch is also
causing ipw2200 driver being impossible to build.
To me this clearly shows that CONFIG_WEXT is far, far away from being
"deprecated enough" to be removed.
[1] http://thread.gmane.org/gmane.linux.kernel/1857010
[2] http://thread.gmane.org/gmane.linux.network/343688
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Fix double SKB free in bluetooth 6lowpan layer, from Jukka Rissanen.
2) Fix receive checksum handling in enic driver, from Govindarajulu
Varadarajan.
3) Fix NAPI poll list corruption in virtio_net and caif_virtio, from
Herbert Xu. Also, add code to detect drivers that have this mistake
in the future.
4) Fix doorbell endianness handling in mlx4 driver, from Amir Vadai.
5) Don't clobber IP6CB() before xfrm6_policy_check() is called in TCP
input path,f rom Nicolas Dichtel.
6) Fix MPLS action validation in openvswitch, from Pravin B Shelar.
7) Fix double SKB free in vxlan driver, also from Pravin.
8) When we scrub a packet, which happens when we are switching the
context of the packet (namespace, etc.), we should reset the
secmark. From Thomas Graf.
9) ->ndo_gso_check() needs to do more than return true/false, it also
has to allow the driver to clear netdev feature bits in order for
the caller to be able to proceed properly. From Jesse Gross.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
genetlink: A genl_bind() to an out-of-range multicast group should not WARN().
netlink/genetlink: pass network namespace to bind/unbind
ne2k-pci: Add pci_disable_device in error handling
bonding: change error message to debug message in __bond_release_one()
genetlink: pass multicast bind/unbind to families
netlink: call unbind when releasing socket
netlink: update listeners directly when removing socket
genetlink: pass only network namespace to genl_has_listeners()
netlink: rename netlink_unbind() to netlink_undo_bind()
net: Generalize ndo_gso_check to ndo_features_check
net: incorrect use of init_completion fixup
neigh: remove next ptr from struct neigh_table
net: xilinx: Remove unnecessary temac_property in the driver
net: phy: micrel: use generic config_init for KSZ8021/KSZ8031
net/core: Handle csum for CHECKSUM_COMPLETE VXLAN forwarding
openvswitch: fix odd_ptr_err.cocci warnings
Bluetooth: Fix accepting connections when not using mgmt
Bluetooth: Fix controller configuration with HCI_QUIRK_INVALID_BDADDR
brcmfmac: Do not crash if platform data is not populated
ipw2200: select CFG80211_WEXT
...
Commit ac61d19559 (scsi: set correct completion code in
scsi_send_eh_cmnd()) introduced a bug. It changed the stored return
value from a queuecommand call, but it didn't take into account that
the return value was used again later on. This patch fixes the bug by
changing the later usage.
There is a big comment in the middle of scsi_send_eh_cmnd() which
does a good job of explaining how the routine works. But it mentions
a "rtn = FAILURE" value that doesn't exist in the code. This patch
adjusts the code to match the comment (I assume the comment is right
and the code is wrong).
This fixes Bugzilla #88341.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Андрей Аладьев <aladjev.andrew@gmail.com>
Tested-by: Андрей Аладьев <aladjev.andrew@gmail.com>
Fixes: ac61d19559
Acked-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix a copy and paste error in the kernel doc description for the params_*()
functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few fixes for v3.19, a few driver specifics and one core fix which
fixes a boot crash on OMAP if deferred probing kicks in due to
attempting to modify static data.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUoXnhAAoJECTWi3JdVIfQU98H+wYL3/11DUS+qOhjkHBUzStB
VIIuw4Zf1gfEG+0gPSVI/oE0nTVZyYGGV2qIn01SDPMjOdcCRpC5sdwHDEN/YNXR
v9zpWydtUILkram4xXsUiqyJTznPOeqM7HUVROZu3IkR3IcFZ8eCjoXghZXcNuWo
6RezroZkV3KhUrxSWl0D07cWfl76dJt4XSKrT9a1iFGFg1fMBK9PwquhNbD1vami
n2kR740u95wDPIbxRliBm6yYuJ6D2Fwi5BmCGfp4gml+685tXMBmDZ26+W3nKQdZ
TiZyhMbtcGN3rYEoaKwHEeTCgfQtMxgxoyhcniOIZvbiV9oT3jtTJAl38xnnS5E=
=pFlY
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.19
A few fixes for v3.19, a few driver specifics and one core fix which
fixes a boot crash on OMAP if deferred probing kicks in due to
attempting to modify static data.
Currently we enable Exynos devices in the multi v7 defconfig, however, when
testing on my ODROID-U3, I noticed that USB was not working. Enabling this
option causes USB to work, which enables networking support as well since the
ODROID-U3 has networking on the USB bus.
[arnd] Support for odroid-u3 was added in 3.10, so it would be nice to
backport this fix at least that far.
Signed-off-by: Steev Klimaszewski <steev@gentoo.org>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5CnD
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-3.19' of git://git.infradead.org/linux-mvebu into fixes
Pull "Fixes for 3.19" from Andrew Lunn:
Jason is taking a back seat this cycle and i'm doing all the patch
wrangling for mvebu.
* tag 'mvebu-fixes-3.19' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Fix pinctrl configuration for Armada 370 DB
Also update to Linux 3.19-rc1, which this was based on.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Unfortunately, while commit 4a928436 ("audit: correctly record file
names with different path name types") fixed a problem where we were
not recording filenames, it created a new problem by attempting to use
these file names after they had been freed. This patch resolves the
issue by creating a copy of the filename which the audit subsystem
frees after it is done with the string.
At some point it would be nice to resolve this issue with refcounts,
or something similar, instead of having to allocate/copy strings, but
that is almost surely beyond the scope of a -rcX patch so we'll defer
that for later. On the plus side, only audit users should be impacted
by the string copying.
Reported-by: Toralf Foerster <toralf.foerster@gmx.de>
Signed-off-by: Paul Moore <pmoore@redhat.com>
When I/O is aborted by mid-layer, fnic FW will complete the I/O before
completing the abort task. In some cases abort request is completed before
the I/O, which could lead to inconsistent driver and firmware states.
In this case firmware reset would clear the inconsistent state.
Signed-off-by: Anil Chintalapati <achintal@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Hiral Shah <hishah@cisco.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
7985090aa0 changed the discard heuristics to give preference to the
WRITE SAME commands that (unlike UNMAP) guarantee deterministic results.
Ming Lei discovered that QEMU SCSI's WRITE SAME implementation
internally relied on limits that were only communicated for the UNMAP
case. And therefore discard commands backed by WRITE SAME would fail.
Tweak the heuristics so we still pick UNMAP in the LBPRZ=0 case and only
prefer the WRITE SAME variants if the device has the LBPRZ flag set.
Reported-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
