The code to handle AXP803_ID and AXP813_ID cases are exactly the same.
Make the switch-case fall through to avoid duplicate code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_desc arrays in this driver are indexed by RN5T618_*
constants and some elements can be missing. This causes probe failures
on older models:
rn5t618-regulator rn5t618-regulator: failed to register (null) regulator
rn5t618-regulator: probe of rn5t618-regulator failed with error -22
Fix this by making the arrays flat. This also saves a little memory
because the regulator_desc arrays become smaller.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 83b2a3c2ab ("regulator: rn5t618: add RC5T619 PMIC support")
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver boots only via device tree hence add a
dependency on CONFIG_OF. This leaves with a bunch of unused code
so clean that up. This patch also makes use of probe_new function
in place of the probe function so as to avoid passing i2c_device_id.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP813 PMIC has 7 DC-DC buck regulators, 16 LDOs (including the
fixed RTC LDO and 2 GPIO LDOs), and 1 switchable. The drive-vbus
feature is also supported. All the hardware details are very similar
to the AXP803, with the following exceptions:
- Extra DCDC7 buck regulator, with the same range as DCDC6
- SWitch now has a separate supply pin, instead of being chained
internaly from DCDC1
- RTC LDO output voltage is now 1.8V
- FLDO3 is an LDO with switchable supplies, but unconfigurable output
voltage. The voltage is always half that of its supply.
Support for FLDO3 is currently unimplemented, as it requires runtime
switching of its supplies, something the regulator subsystem does not
support. It is not used in either the reference designs nor actually
produced boards available.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bit offset used to check if DCDC5 and DCDC6 are tied together in
poly-phase output is wrong. It was checking against a reserved bit,
which is always false.
In reality, neither the reference design layout nor actually produced
boards tie these two buck regulators together. But we should still
fix it, just in case.
Fixes: 1dbe0ccb06 ("regulator: axp20x-regulator: add support for AXP803")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlmpiLATHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0A7zB/4+ejX3TwY9Jbj5Fc7TchcxDogn9OJr
fT7E8Nz4Q+XxMLTppOCRbE3t6/c/d5ILDwB4fG8Z2IJckrOcallB67hpX1ArXfT2
4VKBQQx6bN55Bu2WAMz4ZC//uhD62Mw9QJS0PuCzkGJtcCnLvb5YFUbrI6KBBoSD
PirGdcatZezm4G5cPRIYu0vHtadokljUx1qx/ZyNsEU562RsLuvPtI8IjItBTQ9E
ryRgQjM+rMoBajy9qeHWKLzQVXr5sGuVMtv7EGUx/YzJ+xDjsCjyK0lI/Z14XGgx
yDnzkTQWWmI8o6Kmn5VW7/F6CVuck/g3ozLtVbSBJZQe2h/FJk7q/2vQ
=jJF/
-----END PGP SIGNATURE-----
Merge tag 'regulator-pbias-variants'
This pulls in a regulator change for OMAP from
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
regulator: Add support for different OMAP variants in the pbias regulator
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
- New Device Support
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
- New Functionality
- Amend API to provide register layout; atmel-smc
- Fix-ups
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
- Bug Fixes
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll
-----BEGIN PGP SIGNATURE-----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=TKIm
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
- Drop the P-state selection algorithm based on a PID controller
from intel_pstate and make it use the same P-state selection
method (based on the CPU load) for all types of systems in the
active mode (Rafael Wysocki, Srinivas Pandruvada).
- Rework the cpufreq core and governors to make it possible to
take cross-CPU utilization updates into account and modify the
schedutil governor to actually do so (Viresh Kumar).
- Clean up the handling of transition latency information in the
cpufreq core and untangle it from the information on which drivers
cannot do dynamic frequency switching (Viresh Kumar).
- Add support for new SoCs (MT2701/MT7623 and MT7622) to the
mediatek cpufreq driver and update its DT bindings (Sean Wang).
- Modify the cpufreq dt-platdev driver to autimatically create
cpufreq devices for the new (v2) Operating Performance Points
(OPP) DT bindings and update its whitelist of supported systems
(Viresh Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen,
Finley Xiao).
- Add support for Ux500 to the cpufreq-dt driver and drop the
obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
- Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
Nguyen).
- Fix and clean up assorted issues in the cpufreq drivers and core
(Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
- Update the IO-wait boost handling in the schedutil governor to
make it less aggressive (Joel Fernandes).
- Rework system suspend diagnostics to make it print fewer messages
to the kernel log by default, add a sysfs knob to allow more
suspend-related messages to be printed and add Low Power S0 Idle
constraints checks to the ACPI suspend-to-idle code (Rafael
Wysocki, Srinivas Pandruvada).
- Prefer suspend-to-idle over S3 on ACPI-based systems with the
ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
interface present in the ACPI tables (Rafael Wysocki).
- Update documentation related to system sleep and rename a number
of items in the code to make it cleare that they are related to
suspend-to-idle (Rafael Wysocki).
- Export a variable allowing device drivers to check the target
system sleep state from the core system suspend code (Florian
Fainelli).
- Clean up the cpuidle subsystem to handle the polling state on
x86 in a more straightforward way and to use %pOF instead of
full_name (Rafael Wysocki, Rob Herring).
- Update the devfreq framework to fix and clean up a few minor
issues (Chanwoo Choi, Rob Herring).
- Extend diagnostics in the generic power domains (genpd) framework
and clean it up slightly (Thara Gopinath, Rob Herring).
- Fix and clean up a couple of issues in the operating performance
points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
- Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
(AVS) driver (David Wu).
- Fix the usage of notifiers in CPU power management on some
platforms (Alex Shi).
- Update the pm-graph system suspend/hibernation and boot profiling
utility (Todd Brandt).
- Make it possible to run the cpupower utility without CPU0 (Prarit
Bhargava).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mAiV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This time (again) cpufreq gets the majority of changes which mostly
are driver updates (including a major consolidation of intel_pstate),
some schedutil governor modifications and core cleanups.
There also are some changes in the system suspend area, mostly related
to diagnostics and debug messages plus some renames of things related
to suspend-to-idle. One major change here is that suspend-to-idle is
now going to be preferred over S3 on systems where the ACPI tables
indicate to do so and provide requsite support (the Low Power Idle S0
_DSM in particular). The system sleep documentation and the tools
related to it are updated too.
The rest is a few cpuidle changes (nothing major), devfreq updates,
generic power domains (genpd) framework updates and a few assorted
modifications elsewhere.
Specifics:
- Drop the P-state selection algorithm based on a PID controller from
intel_pstate and make it use the same P-state selection method
(based on the CPU load) for all types of systems in the active mode
(Rafael Wysocki, Srinivas Pandruvada).
- Rework the cpufreq core and governors to make it possible to take
cross-CPU utilization updates into account and modify the schedutil
governor to actually do so (Viresh Kumar).
- Clean up the handling of transition latency information in the
cpufreq core and untangle it from the information on which drivers
cannot do dynamic frequency switching (Viresh Kumar).
- Add support for new SoCs (MT2701/MT7623 and MT7622) to the mediatek
cpufreq driver and update its DT bindings (Sean Wang).
- Modify the cpufreq dt-platdev driver to autimatically create
cpufreq devices for the new (v2) Operating Performance Points (OPP)
DT bindings and update its whitelist of supported systems (Viresh
Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen, Finley
Xiao).
- Add support for Ux500 to the cpufreq-dt driver and drop the
obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
- Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
Nguyen).
- Fix and clean up assorted issues in the cpufreq drivers and core
(Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
- Update the IO-wait boost handling in the schedutil governor to make
it less aggressive (Joel Fernandes).
- Rework system suspend diagnostics to make it print fewer messages
to the kernel log by default, add a sysfs knob to allow more
suspend-related messages to be printed and add Low Power S0 Idle
constraints checks to the ACPI suspend-to-idle code (Rafael
Wysocki, Srinivas Pandruvada).
- Prefer suspend-to-idle over S3 on ACPI-based systems with the
ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
interface present in the ACPI tables (Rafael Wysocki).
- Update documentation related to system sleep and rename a number of
items in the code to make it cleare that they are related to
suspend-to-idle (Rafael Wysocki).
- Export a variable allowing device drivers to check the target
system sleep state from the core system suspend code (Florian
Fainelli).
- Clean up the cpuidle subsystem to handle the polling state on x86
in a more straightforward way and to use %pOF instead of full_name
(Rafael Wysocki, Rob Herring).
- Update the devfreq framework to fix and clean up a few minor issues
(Chanwoo Choi, Rob Herring).
- Extend diagnostics in the generic power domains (genpd) framework
and clean it up slightly (Thara Gopinath, Rob Herring).
- Fix and clean up a couple of issues in the operating performance
points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
- Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
(AVS) driver (David Wu).
- Fix the usage of notifiers in CPU power management on some
platforms (Alex Shi).
- Update the pm-graph system suspend/hibernation and boot profiling
utility (Todd Brandt).
- Make it possible to run the cpupower utility without CPU0 (Prarit
Bhargava)"
* tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (87 commits)
cpuidle: Make drivers initialize polling state
cpuidle: Move polling state initialization code to separate file
cpuidle: Eliminate the CPUIDLE_DRIVER_STATE_START symbol
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
PM: docs: Delete the obsolete states.txt document
PM: docs: Describe high-level PM strategies and sleep states
PM / devfreq: Fix memory leak when fail to register device
PM / devfreq: Add dependency on PM_OPP
PM / devfreq: Move private devfreq_update_stats() into devfreq
PM / devfreq: Convert to using %pOF instead of full_name
PM / AVS: rockchip-io: add io selectors and supplies for RV1108
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpuidle: Convert to using %pOF instead of full_name
cpufreq: Convert to using %pOF instead of full_name
PM / Domains: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
...
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reference manuals of OMAP5x and DRA7x have been updated to reflect
the PBIAS regulator max-voltage as 3.3V instead of 3.0V, while OMAP3x
and OMAP4x are still quoting 3.0V. So, as of now, the pbias driver
needs to support both 3.0V and 3.3V IO voltage based on the max-voltage
supported by the PBIAS regulator.
Document reference:
SWPU249AF - OMAP543x Technical reference manual - August 2016
SPRUI30C – DRA75x, DRA74x Technical reference manual November 2016
Tested on:
DRA75x PG 2.0 REV H EVM
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator driver for STM32 voltage reference buffer which can be
used as voltage reference for ADCs, DACs and external components through
dedicated VREF+ pin.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a patch for exception handlding that the index of array is
out of bounds. And the definitions have been updated to use
proper device name.
Signed-off-by: Eric Jeong <eric.jeong.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If "regl_pdata->n_regulators == 0" is true then we accidentally return
PTR_ERR(<some_valid_pointer>) instead of an error code. I've changed it
to return -ENODEV instead.
Fixes: 69ca3e58d1 ("regulator: da9063: Add Dialog DA9063 voltage regulators support.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the driver to support Ricoh RC5T619.
Support the additional regulators and slightly different voltage ranges.
Signed-off-by: Pierre-Hugues Husson <phh@phh.me>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The device tree nodes all correctly describe the regulators as
syr827 or syr828, but the I2C device id is currently set to the
wildcard value of syr82x in the driver. This causes udev to fail
to match the driver module with the modalias data from sysfs.
Fix this by replacing the I2C device ids with ones that match the
device tree descriptions, with syr827 and syr828. Tested on
Firefly rk3288 board. The syr82x id was not used anywhere.
Fixes: e80c47bd73 (regulator: fan53555: Export I2C module alias information)
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the rk805 regulator. The regulator module consists
of 4 DCDCs, 3 LDOs.
The output voltages are configurable and are meant to supply power
to the main processor and other components.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MT6380 is a regulator found those boards with MediaTek MT7622 SoC
It is connected as a slave to the SoC using MediaTek PMIC wrapper which
is the common interface connecting with Mediatek made various PMICs.
Signed-off-by: Chenglin Xu <chenglin.xu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To make it clear that the symbol in question refers to
suspend-to-idle, rename it from PM_SUSPEND_FREEZE to
PM_SUSPEND_TO_IDLE.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A race condition between queueing and processing the disable_work
instances results in having a work instance in the queue and the
deferred_disables variable of regulator device structure having a
value '0'. If no new regulator_disable_deferred() call later from
clients, the deferred_disables variable value remains '0' and hits
BUG() in regulator_disable_work() when the queued instance scheduled
for processing the work.
The race occurs as below:
Core-0 Core-1
..... /* deferred_disables = 2 */ .....
..... /* disable_work is queued */ .....
..... .....
regulator_disable_deferred: regulator_disable_work:
mutex_lock(&rdev->mutex); .....
rdev->deferred_disables++; .....
mutex_unlock(&rdev->mutex); .....
queue_delayed_work(...) mutex_lock(&rdev->mutex);
..... count =rdev->deferred_disables;
..... rdev->deferred_disables = 0;
..... .....
..... mutex_unlock(&rdev->mutex);
..... .....
..... return;
..... .....
/* No new regulator_disable_deferred() calls from clients */
/* The newly queued instance is scheduled for processing */
..... .....
regulator_disable_work:
.....
mutex_lock(&rdev->mutex);
BUG_ON(!rdev->deferred_disables); /* deferred_disables = 0 */
The race is fixed by removing the work instance that is queued while
processing the previous queued instance. Cancel the newly queued instance
from disable_work() handler just after reset the deferred_disables variable
to value '0'. Also move the work queueing step before mutex_unlock in
regulator_disable_deferred().
Also use mod_delayed_work() in the pace of queue_delayed_work() as
queue_delayed_work() always uses the delay requested in the first call
when multiple consumers call regulator_disable_deferred() close in time
and does not guarantee the semantics of regulator_disable_deferred().
Signed-off-by: Tirupathi Reddy <tirupath@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
if fan53555_regulator_probe() is called and the "client->dev.of_node"
isn't NULL, it means OF registered a device with a valid compatible
string, so match cannot be NULL.
Use of_device_get_match_data() to retrieve the drvdata pointer. No
functional change intended.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Boot fails for qcom-apq8074-dragonboard on 4.13-rc1 with error:
OF: ERROR: Bad of_node_put() on /soc/spmi@fc4cf000/pm8941@1/regulators
The error will occur if the configuration is set to:
CONFIG_OF_OVERLAY y
CONFIG_OF_UNITTEST y
CONFIG_OF_DYNAMIC y
CONFIG_OF_RESOLVE y
If CONFIG_OF_DYNAMIC is enabled then of_node_release() detects an
attempt to release a node that is still attached to the device tree.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device tree mode mapping capabilities to the cpcap driver.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The original patch from Tony uses standby mode bit inverted, which is
not correct. This fixes all instances in the driver code for get & set
mode. This did not yet make problems, since mode has not been changed
by any mainline driver so far.
Fixes: 0ad4c07edd ("regulator: cpcap: Add basic regulator support")
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The original patch from Tony uses standby mode bit inverted, which is
not correct. This fixes all instances in the driver code for get & set
mode. This did not yet make problems, since mode has not been changed
by any mainline driver so far.
Fixes: 0ad4c07edd ("regulator: cpcap: Add basic regulator support")
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Check return value from call to devm_kzalloc()
in order to prevent a NULL pointer dereference.
This issue was detected using Coccinelle and the following semantic patch:
@@
expression x;
identifier fld;
@@
* x = devm_kzalloc(...);
... when != x == NULL
x->fld
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check return value from call to of_match_device()
in order to prevent a NULL pointer dereference.
In case of NULL print error message and return.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check return value from call to of_match_device()
in order to prevent a NULL pointer dereference.
In case of NULL print error message and return.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now the debugfs file supply_map has a size limit PAGE_SIZE and the user
can not see the whole content of regulator_map_list when it is larger
than this limit.
This patch uses seq_file instead to make sure supply_map shows the full
information of regulator_map_list.
Signed-off-by: Haishan Zhou <zhssmail@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators support get_voltage() and some support get_voltage_sel()
operations but currently we only propagate changes if the regulator has
a get_voltage() operation. Also do this if we've got get_voltage_sel()
[Rewite commit message for clarity -- broonie]
Signed-off-by: Tirupathi Reddy <tirupath@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The latest documentation reveals that initial voltage range that is
supported is starting from 0.6V for all the PMICs belonging to lp87565
family. Fix the same.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: f0168a9bf ("regulator: lp87565: Add support for lp87565 PMIC regulators")
Signed-off-by: Mark Brown <broonie@kernel.org>
The hi6421v530-regulator driver consumes a similarly named platform device.
Adding that to the module device table, allows modprobe to locate this
driver once the device is created.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check TPS65910_NUM_REGS at build time instead of silently registering
not all regulators at runtime.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, when looking up a regulator supply, the regulator name
takes priority over the consumer mappings. As there are a lot of
regulator names that are in fairly common use (VDD, MICVDD, etc.) this
can easily lead to obtaining the wrong supply, when a system contains
two regulators that share a name.
The explicit consumer mappings contain much less ambiguity as they
specify both a name and a consumer device. As such prioritise those if
one exists and only fall back to the regulator name if there are no
matching explicit mappings.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hi6421-regulator driver consumes a similarly named platform device.
Adding that to the module device table, allows modprobe to locate this
driver once the device is created.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
add the driver for hi6421v530 voltage regulator
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator support for the DA9061 is added into the DA9062 regulator driver.
The regulators for DA9061 differ from those of DA9062.
A new DA9061 enumeration list for the LDOs and Bucks supported by this
device is added. Regulator information added: the old regulator
information for DA9062 is renamed from local_regulator_info[] to
local_da9062_regulator_info[] and a new array is added to support
local_da9061_regulator_info[].
The probe() function switches on the da9062_compatible_types enumeration
and configures the correct da9062_regulator_info array and number of
regulator entries.
Kconfig is updated to reflect support for DA9061 and DA9062 regulators.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These functions are only used by this driver, make them static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
App support for SMPS12 dual phase regulator.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulators set consists of 4 BUCKs. The output
voltages are configurable and are meant to supply power to the
main processor and other components. The ramp delay is configurable
for all BUCKs. The BUCKs can be configured in single phase or
multiphase modes.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AXP803 PMIC also have a series of regulators (DCDCs and LDOs)
controllable via I2C/RSB bus.
Add support for them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in dev_err messages.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators have different settling times for voltage increases and
decreases. To avoid a time penalty on the faster transition allow for
different settings for up- and downward transitions.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop static on a local variable, when the variable is initialized before
any use, on every possible execution path through the function.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
There is no reduction in code size in this case, but the change does reduce
the size of the bss segment, containing uninitialized static data.
before:
text data bss dec hex filename
12882 3480 8 16370 3ff2 drivers/regulator/palmas-regulator.o
after:
text data bss dec hex filename
12882 3480 0 16362 3fea drivers/regulator/palmas-regulator.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
When min charger-CV is <= 4.0V and max charger-CV is >= 4.0V,
we can use 4.00V as CV (register value = 0x1).`
The original code had a typo that wrote ">=" (max_uV >= 4000000),
which should've been "<", which is not necessary anyway
as mentioned by Dan Carpenter.
Reported-By: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for the regulator block in the ROHM BD9571MWV-W MFD PMIC.
This block supports three voltage monitors, VD18, VD25, VD33 for the
1V8, 2V5, 3V3 voltage rails and a single voltage regulator for the
DVFS rail.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for sharing this driver with Madera codecs, factor out
the parts of initialization that aren't dependent on struct arizona.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for supporting Madera codecs, remove the dependency on
struct arizona in the regulator callbacks and struct arizona_ldo1.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for sharing this driver with Madera, move the pdata
for the LDO1 regulator out of struct arizona_pdata into a dedicated
pdata struct for this driver. As a result the code in
arizona_ldo1_of_get_pdata() can be made independent of struct arizona.
This patch also updates the definition of struct arizona_pdata and
the use of this pdata in mach-crag6410-module.c
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for sharing this driver with Madera codecs, factor out
the parts of initialization that aren't dependent on struct arizona.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for supporting Madera codecs, remove the dependency on
struct arizona in the regulator callbacks and struct arizona_micsupp.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for sharing this driver with Madera, move the pdata
for the micsupp regulator out of struct arizona_pdata into a dedicated
pdata struct for this driver. As a result the code in
arizona_micsupp_of_get_pdata() can be made independent of struct arizona.
This patch also updates the definition of struct arizona_pdata and
the use of this pdata in mach-crag6410-module.c
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS47L24 Arizona codec and most Madera codecs do not have a LDO1
regulator. Split the LDO1 and MICSUPP regulators into separate KConfig
options so the LDO1 is only built into the kernel if needed.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 43530b69d7 ("regulator: Use
regmap_read/write(), regmap_update_bits functions directly") intended
to replace working inline helper functions with standard regmap
calls. However, it also inverted the set/clear logic of the "CORE ADJ
Allowed" bit. That patch was clearly never tested, since without that
bit cleared, the core VDCDC1 voltage output does not react to I2C
configuration changes.
This patch fixes the issue by clearing the bit as in the original,
correct implementation. Note for stable back porting that, due to
subsequent driver churn, this patch will not apply on every kernel
version.
Fixes: 43530b69d7 ("regulator: Use regmap_read/write(), regmap_update_bits functions directly")
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
For anatop regulator we must have a name accordingly. Make sure the name
is properly checked before using it to avoid a possible kernel NULL
point crash.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rather than just not resolving the supply when there is explicitly no
supply mapping fall through and allow a dummy supply to be substituted.
This fixes issues with constant retries reported by Dong Aisheng.
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
When we are propagating voltage changes to parent regulators don't
bother if the parent does not have permission to change voltages. This
simplifies error checking in the function for cases where the regulator
lacks some of the voltage operations.
Reported-by: Dong Aisheng <aisheng.dong@nxp.com>
Tested-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code only allocates rdesc->n_voltages entries for vctrl->vtable.
Thus use rdesc->n_voltages instead of n_voltages in the for loop.
While at it, also switch to use devm_kcalloc instead of devm_kmalloc_array
+ __GFP_ZERO flag and fix the argument order.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/regulator/tps65132-regulator.c:274:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the initial voltage selector for vddpcie in case it's disabled
by default.
This fixes the below warning:
20c8000.anatop:regulator-vddpcie: Failed to read a valid default voltage selector.
anatop_regulator: probe of 20c8000.anatop:regulator-vddpcie failed with error -22
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Robin Gong <yibin.gong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator driver for the device TI TPS65132 which is single
inductor - dual output power supply device. TPS65132 device is
designed to support general positive/negative driven applications
like TFT display panels.
TPS65132 regulator driver supports to enable/disable and set voltage
on its output.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sreg->name is only used as an intermediate assign of rdesc->name, plus
another strcmp. Since we already have rdesc->name, no need it anymore.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sreg->name is a string, so use a more proper api to read back the string
instead of of_get_property.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Should check the return value of of_get_regulator_init_data before
using it.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The output voltage of a voltage controlled regulator can be controlled
through the voltage of another regulator. The current version of this
driver assumes that the output voltage is a linear function of the control
voltage.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a helper function regulator_set_pull_down_regmap to allow regmap
based regulators to easily enable pull down.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a helper function regulator_set_soft_start_regmap to allow regmap
based regulators to easily enable soft start.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators (some PWM regulators) have the voltage transition
non-linear i.e. exponentially. On such cases, the settling time
for voltage transition can not be presented in the voltage-ramp-delay.
Add new property for non-linear voltage transition and handle this
in getting the voltage settling time.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hi655x-regulator driver consumes a similarly named platform device.
Adding that to the module device table, allows modprobe to locate this
driver once the device is created.
Signed-off-by: Jeremy Linton <lintonrjeremy@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The device argument passed to of_get_regulator_init_data is used to
do some devres memory allocation. Currently the driver passes the MFD
device pointer to this function, this could result in the init_data
allocation being leaked if the regulator is unbound but the MFD isn't.
Correct this issue by correctly passing the local platform device.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The device argument passed to of_get_regulator_init_data is used to
do some devres memory allocation. Currently the driver passes the MFD
device pointer to this function, this could result in the init_data
allocation being leaked if the regulator is unbound but the MFD isn't.
Correct this issue by correctly passing the local platform device.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 26988efe11 ("regulator: core: Allow to get voltage count and
list from parent") introduces the propagation of the parent voltage
count and list for regulators that don't provide this information
themselves. The goal is to support simple switch regulators, however as
a side effect normal continuous regulators can leak details of their
supplies and provide consumers with inconsistent information.
Limit the propagation of the voltage count and list to switch
regulators.
Fixes: 26988efe11 ("regulator: core: Allow to get voltage count and
list from parent")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the description for the non-existing 'ret' to fix the build warning:
./drivers/regulator/core.c:1467: warning:
Excess function parameter 'ret' description in 'regulator_dev_lookup'.
The description found for the return value is: @ret: 0 on success, -ENODEV
if lookup fails permanently, -EPROBE_DEFER if lookup could succeed in the future.
Signed-off-by: Tamara Diaconita <diaconita.tamara@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is useful for devices, which need some time to start up, to help
the drivers track how long the supply has been up already. Ie whether
it can safely talk to the HW or needs to wait.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the correct voltage select register for LDO2.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
It has been pointed out to me that the range for vsel = 58 is actually
dead code as this is covered by an earlier check for (min_uV >= 700000)
&& (min_uV <= 1420000) so remove that check completely.
Reported-by: Alban Auzeill <alban.auzeill@sonarsource.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The supply_name member of struct regulator can be const as we
don't change it in the regulator core. Furthermore, when we copy
the supply name we can use kstrdup_const() here to avoid a copy
if the name is in the ro data section.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broken indenting makes code more difficult to read and brings
confusion. Fix warning reported by Smatch:
s2mpa01.c:362 s2mpa01_pmic_probe() warn: inconsistent indenting
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Static struct regulator_ops is not modified so can be made const for
code safeness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Static struct regulator_ops is not modified so can be made const for
code safeness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Static struct regulator_ops is not modified so can be made const for
code safeness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Static struct regulator_ops (except max8660_dcdc_ops) are not modified
so can be made const for code safeness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Static struct regulator_ops is not modified so can be made const for
code safeness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Static struct regulator_ops is not modified so can be made const for
code safeness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for PF0200 coin cell/super capacitor charger which works as
a current limited voltage source via the LICELL pin. When VIN goes below
a certain threshold LICELL is used to provide power for VSNVS which is
usually used to hold up secure non-volatile storage and the real-time
clock on the SoC.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vpos and Vneg LDOs can be enabled or disabled by external GPIOs.
Use general DT property 'enable-gpios' for this usage.
Two enable pins are differentiable by selecting the index number.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When creating the link to the device sysfs entry, the regulator core
calls scnprintf() and then checks if the returned value is greater or
equal than the buffer size.
The former can never happen as scnprintf() returns the number of bytes
that were actually written to the buffer, not the bytes that *would*
have been written.
Use the right function in this case: snprintf().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a lot of work going on the core this release, mainly around system
initialization, but a quiet release for drivers:
- Fixes for registration of multiple regulators on a PMIC from Javier
Martinez Canillas and Jon Hunter.
- Cleanups to the regulator_get() code from Dmitry Torokhov
- Lots of constifcation of structs from Bhumika Goyal
- Support for Motorola CPCAP regulators from Tony Lindgren.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlirPJwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0OJyB/sH4ug2B14/NQjWg/K3M382lUcV24+x
rgq7ucelmHStrqnSU/DTauGL3uoU3Mc9ibGx7nK4SCWaylHpcZjI42dqG+Tkw/CG
/NlF++JOD0lmlXN1kUTqjFyLOGX9Mt5p4Rnbh3xWWJ5Gq30y6IcIJXILrs/9zI4G
OPhAp5Zq7cwT/00PEIxXtI2OcWx9cIeOIwmwE8S0hvNkVQ5oUz5VV+43ZooFVXrN
4l4GzJgEu3huF/zaWq0lW0HHlhWbLcZGNzg8B+6//V3Xrq7dapyQ5vXpARC8DsFm
Q1n2eJlsdbwjTiQy5xOCmk76GnneGt8/6ifhNKidc5LKfoy7DVfPfIF7
=qvYg
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Quite a lot of work going on the core this release, mainly around
system initialization, but a quiet release for drivers:
- fixes for registration of multiple regulators on a PMIC from Javier
Martinez Canillas and Jon Hunter.
- cleanups to the regulator_get() code from Dmitry Torokhov
- lots of constifcation of structs from Bhumika Goyal
- support for Motorola CPCAP regulators from Tony Lindgren"
* tag 'regulator-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (52 commits)
regulator: core: Resolve supplies before disabling unused regulators
regulator: Fix regulator_summary for deviceless consumers
regulator: tps65086: Fix DT node referencing in of_parse_cb
regulator: tps65086: Fix expected switch DT node names
regulator: core: simplify _regulator_get()
regulator: core: have regulator_dev_lookup() return ERR_PTR-encoded errors
regulator: gpio: correct default type
regulator: cpcap: Add basic regulator support
regulator: core: fix typo in regulator_bulk_disable()
regulator: core: optimize devm_regulator_bulk_get()
regulator: core: simplify regulator_bulk_force_disable()
regulator: core: have _regulator_get() accept get_type argument
regulator: core: remove dead code in _regulator_get()
regulator: rn5t618: constify regulator_ops structure
regulator: rc5t583-regulator: constify regulator_ops structure
regulator: pv88090-regulator: constify regulator_ops structure
regulator: pv88080-regulator: constify regulator_ops structure
regulator: pv88060-regulator: constify regulator_ops structure
regulator: pfuze100-regulator: constify regulator_ops structure
regulator: pcf50633-regulator: constify regulator_ops structure
...
After commit 66d228a2bf ("regulator: core: Don't use regulators as
supplies until the parent is bound"), input supplies aren't resolved
if the input supplies parent device has not been bound. This prevent
regulators to hold an invalid reference if its supply parent device
driver probe is deferred.
But this causes issues on some boards where a PMIC's regulator use as
input supply a regulator from another PMIC whose driver is registered
after the driver for the former.
In this case the regulators for the first PMIC will fail to resolve
input supplies on regulators registration (since the other PMIC wasn't
probed yet). And when the core attempts to resolve again latter when
the other PMIC registers its own regulators, it will fail again since
the parent device isn't bound yet.
This will cause some parent supplies to never be resolved and wrongly
be disabled on boot due taking them as unused.
To solve this problem, also attempt to resolve the pending regulators
input supplies before disabling the unused regulators.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is allowed to call regulator_get with a NULL dev argument
(_regulator_get explicitly checks for it) but this causes an error later
when printing /sys/kernel/debug/regulator_summary.
Fix this by explicitly handling "deviceless" consumers in the debugfs code.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When we check for additional DT properties in the current node we
use the device_node passed in with the configuration data, this
will not point to the correct DT node, use the one passed in
for this purpose.
Fixes: d2a2e729a6 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Reported-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The three load switches are called SWA1, SWB1, and SWB2. The
node names describing properties for these are expected to be
the same, but due to a typo they are not. Fix this here.
Fixes: d2a2e729a6 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Reported-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code in _regulator_get() got a bit confusing over time, with control
flow jumping to a label from couple of places. Let's untangle it a bit by
doing the following:
1. Make handling of missing supplies and substituting them with dummy
regulators more explicit:
- check if we not have full constraints and refuse considering dummy
regulators with appropriate message;
- use "switch (get_type)" to handle different types of request explicitly
as well. "Normal" requests will get dummies, exclusive will not and
will notify user about that; optional will fail silently.
2. Stop jumping to a label in the middle of the function but instead have
proper conditional flow. I believe jumps should be reserved for error
handling, breaking from inner loop, or restarting a loop, but not for
implementing normal conditional flow.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of returning both regulator_dev structure as return value and
auxiliary error code in 'ret' argument, let's switch to using ERR_PTR
encoded values. This makes it more obvious what is going on at call sites.
Also, let's not unlock the mutex in the middle of a loop, but rather break
out and have single unlock path.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many Motorola phones like droid 4 are using a custom PMIC called CPCAP
or 6556002. This PMIC is used with several SoCs, I've noticed at least
omap3, omap4 and Tegra2 based Motorola phones and tablets using it.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When performing this bulk operation, there is no need to track every supply
individually. It is more efficient to treat entire group as a single
managed resource.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to have two loops there, we can store error for subsequent
reporting.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of separate "exclusive" and "allow_dummy" arguments, that formed 3
valid combinations (normal, exclusive and optional) and an invalid one,
let's accept explicit "get_type", like we did in devm-managed code.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no point in assigning value to 'ret' before calling
regulator_dev_lookup() as it will clobber 'ret' anyway.
Also, let's explicitly return -PROBE_DEFER when try_module_get() fails,
instead of relying that earlier initialization of "regulator" carries
correct value.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Three changes here, two run of the mill driver specific fixes and a
change from Mark Rutland which reverts some new device specific ACPI
binding code which was added during the merge window as there are
concerns about this sending the wrong signal about usage of regulators
in ACPI systems.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAliUbfoTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0A9tB/4zf8o0ueo5kT2+15FZBozyY9iKMZl6
daIGxXdJlHjUoCawoq00az3SxELPx0ydq+Cl2A1/lpJAwy0RZ/K1NnIC/bddI9xD
m9DsgictpVqrl/XF6+9WIutXq4FTGQVWD7VbkG0pP/MF80tEzskTTNwe9uGjgeeu
tJAF0ksYC0wA8pG1ukTyAU5zthv6Vr4VSTq8ETpVkpwMiE7nfLtDlf468xg8L8ng
4JAgZA0AsEOWnDRQvc7gCFEmn41rl0WfQNnf/CdnjnrefVpFoW7+paU6a8mgGRqD
+8hiNaqvgjgGfICQV6eFpGoP//9jRvisEOxl255ZATXEKZ5fjdBOKd3T
=7XMg
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Three changes here: two run of the mill driver specific fixes and a
change from Mark Rutland which reverts some new device specific ACPI
binding code which was added during the merge window as there are
concerns about this sending the wrong signal about usage of regulators
in ACPI systems"
* tag 'regulator-fix-v4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fixed: Revert support for ACPI interface
regulator: axp20x: AXP806: Fix dcdcb being set instead of dcdce
regulator: twl6030: fix range comparison, allowing vsel = 59
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/rn5t618-regulator.o
text data bss dec hex filename
375 5392 0 5767 1687 regulator/rn5t618-regulator.o
File size after: drivers/regulator/rn5t618-regulator.o
text data bss dec hex filename
631 5136 0 5767 1687 regulator/rn5t618-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/rc5t583-regulator.o
text data bss dec hex filename
931 3824 0 4755 1293 regulator/rc5t583-regulator.o
File size after: drivers/regulator/rc5t583-regulator.o
text data bss dec hex filename
1187 3568 0 4755 1293 regulator/rc5t583-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/pv88090-regulator.o
text data bss dec hex filename
2829 2032 8 4869 1305 regulator/pv88090-regulator.o
File size after: drivers/regulator/pv88090-regulator.o
text data bss dec hex filename
3341 1520 8 4869 1305 regulator/pv88090-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/pv88080-regulator.o
text data bss dec hex filename
3828 1808 8 5644 160c regulator/pv88080-regulator.o
File size after: drivers/regulator/pv88080-regulator.o
text data bss dec hex filename
4340 1296 8 5644 160c regulator/pv88080-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/pv88060-regulator.o
text data bss dec hex filename
6195 752 8 6955 1b2b regulator/pv88060-regulator.o
File size after: drivers/regulator/pv88060-regulator.o
text data bss dec hex filename
6739 240 8 6987 1b4b regulator/pv88060-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/pfuze100-regulator.o
text data bss dec hex filename
3552 12528 16 16096 3ee0 regulator/pfuze100-regulator.o
File size after: drivers/regulator/pfuze100-regulator.o
text data bss dec hex filename
4576 11496 16 16088 3ed8 regulator/pfuze100-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/pcf50633-regulator.o
text data bss dec hex filename
2763 464 0 3227 c9b regulator/pcf50633-regulator.o
File size after: drivers/regulator/pcf50633-regulator.o
text data bss dec hex filename
3019 192 0 3211 c8b regulator/pcf50633-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/pcap-regulator.o
text data bss dec hex filename
5503 564 0 6067 17b3 regulator/pcap-regulator.o
File size after: drivers/regulator/pcap-regulator.o
text data bss dec hex filename
5759 308 0 6067 17b3 regulator/pcap-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/pbias-regulator.o
text data bss dec hex filename
2545 624 0 3169 c61 regulator/pbias-regulator.o
File size after: drivers/regulator/pbias-regulator.o
text data bss dec hex filename
2801 368 0 3169 c61 regulator/pbias-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/palmas-regulator.o
text data bss dec hex filename
9752 6296 288 16336 3fd0 regulator/palmas-regulator.o
File size after: drivers/regulator/palmas-regulator.o
text data bss dec hex filename
12856 3480 8 16344 3fd0 regulator/palmas-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/max8952.o
text data bss dec hex filename
3048 496 0 3544 dd8 drivers/regulator/max8952.o
File size after: drivers/regulator/max8952.o
text data bss dec hex filename
3304 240 0 3544 dd8 drivers/regulator/max8952.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/max8925-regulator.o
text data bss dec hex filename
1356 7184 0 8540 215c regulator/max8925-regulator.o
File size after: drivers/regulator/max8925-regulator.o
text data bss dec hex filename
1868 6664 0 8532 2154 regulator/max8925-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/max8907-regulator.o
text data bss dec hex filename
1384 9424 256 11064 2b38 regulator/max8907-regulator.o
File size after: drivers/regulator/max8907-regulator.o
text data bss dec hex filename
2664 8400 0 11064 2b38 regulator/max8907-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/max77802-regulator.o
text data bss dec hex filename
11811 1552 0 13363 3433 regulator/max77802-regulator.o
File size after: drivers/regulator/max77802-regulator.o
text data bss dec hex filename
13091 272 0 13363 3433 regulator/max77802-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/max77693-regulator.o
text data bss dec hex filename
2230 720 0 2950 b86 regulator/max77693-regulator.o
File size after: drivers/regulator/max77693-regulator.o
text data bss dec hex filename
2486 464 0 2950 b86 regulator/max77693-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>