This reverts commit c9ba7a16d0 (Release spi_res after finalizing
message) which causes races during cleanup.
Reported-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
When GPIO chip-select is used nothing prevents any available SPI
controllers to work with both CS-high and traditional CS-low modes.
In fact the SPI bus core code already does it, so we don't need to
introduce any modification there. But spi_setup() still fails to
switch the interface settings if CS-high flag is set for the case
of GPIO-driven slave chip-select when the SPI controller doesn't
support the hardwired CS-inversion. Lets fix it by clearing the
SPI_CS_HIGH flag out from bad_bits (unsupported by controller) when
client chip is selected by GPIO.
This feature is useful for slave devices, which in accordance with
communication protocol can work with both active-high and active-low
chip-selects. I am aware of one such device. It is MMC-SPI interface,
when at init sequence the driver needs to perform a read operation with
low and high chip-select sequentially (requirement of 74 clock cycles
with both chipselect, see the mmc_spi driver for details).
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the EP93xx SPI master driver to use GPIO
descriptors for chip select handling.
EP93xx was using platform data to pass in GPIO lines,
by converting all board files to use GPIO descriptor
tables the core will look up the GPIO lines from the
SPI device in the same manner as for device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Alpha and some of the architectures are missing readsl/writesl functions.
so the zynq-qspi driver won't be able to build on these arches. hence use
ioread32_rep()/iowrite32_rep() instead of readsl()/writesl().
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During probe, check the "get_irq" error value.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Split spi transfers into chunks of <=65532 to enable the driver to
perform DMA transfer on big buffers. The DLEN register specifies the
number of bytes to transfer in DMA mode. It is 16-bit wide and thus the
maximum DMA transfer is 65535 bytes. Set the maximum to 65532 (4 byte
aligned) since the FIFO in DMA mode is accessed in 4 byte chunks.
->max_dma_len is the value the spi core uses when splitting the buffer
into scatter gather entries.
The BCM2835 DMA block has 2 types of channels/engines:
- Normal: Max length: 1G
- Lite: Max length: 65535
Even when using a Lite channel we will not exceed the max length, so
let's drop setting ->max_dma_len.
Signed-off-by: Meghana Madhyastha <meghana.madhyastha@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add PCI IDs for SPI on Comet Lake.
Signed-off-by: Evan Green <evgreen@chromium.org>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_split_transfers_maxsize() can be used to split a transfer. This
function uses spi_res to lifetime manage the added transfer structures.
So in order to finalize the current message while it contains the split
transfers, spi_res_release() must be called after finalizing.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't warn about splitting transfers, the info is available in the
statistics if needed.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Falling back to maximum speed of the controller in case of SPI slave
maximum speed is not set is needless. It already defaults to maximum
speed of the controller since commit 052eb2d490 ("spi: core: Set
max_speed_hz of spi_device default to max_speed_hz of controller").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With dw_dmac, sometimes the request of a DMA channel fails because
the DMA driver is not ready, so an explicit dependency request
is necessary.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch creates set_cs_timing SPI master optional method for
SPI masters to implement configuring CS timing if applicable.
This patch also creates spi_cs_timing accessory for SPI clients to
use for requesting SPI master controllers to configure device requested
CS setup time, hold time and inactive delay.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch creates tegra_spi_soc_data structure to maintain and implement
SPI HW feature differences between different Tegra chips and also creates
a separate compatible string for T124/T210.
Tegra210 and later has a separate interrupt mask register SPI_INTR_MASK
for enabling or disabling interrupts while Tegra124 and prior uses
interrupt enable bits in SPI_DMA_CTL register.
This patch creates flag has_intr_mask_reg in tegra_spi_soc_data to
identify this and implements accordingly.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds 3 wire transfer support to SPI mode list along with
its implementation.
3 wire or Bi-directional mode uses only one serial data pin for the
transfer. SPI in master mode uses MOSI data line only and MISO data
line is not used.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for dual mode SPI transfer.
Dual mode uses both MOSI and MISO lines in parallel where the data
is interleaved on MOSI and MISO lines increasing the throughput.
Packet from Tx FIFO is transmitted on both MOSI and MISO lines and
packet to Rx FIFO is received from both MOSI and MISO lines. Even
bits are transmitted or received on the MOSI data line and odd bits
are transmitted or received on the MISO data line.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace spi_bitbang_start() with a combination of spi_bitbang_init()
and devm_spi_register_master() and drop all of the explicit
cleanup-related code that's no longer necessary.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Move all of the code doing struct spi_bitbang initialization, so that
it can be paired with devm_spi_register_master() in order to avoid
having to call spi_bitbang_stop() explicitly.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a number of failure paths in spi_gpio_probe() that do not call
spi_master_put() potentially leaking memory. Fix this problem by
registering a cleanup funciont via devm_add_action_or_reset() right
after SPI controller is allocated.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the type of the diagnostic message:
"no DMA channels available, using PIO"
from debug to warning.
The lack of an available DMA channel is very important regard the
spi-pxa2xx performance. The transfer speed can be reduced more than 50%.
So it is very important to warn the user about this, without enabling
the full SPI debug with CONFIG_SPI_DEBUG.
Moreover, enabling the full SPI debug only to enable this specific
debug message, the dmesg buffer fills quickly with a lot of
repetitive information during the SPI data transfer.
This cause the loss of all the first important messages
written during the initialization.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use is_slave local variable to avoid calling of_property_read_bool() twice.
Remove redudant assignment for controller->bus_num, set it once is enough.
Move setting controller->bits_per_word_mask close to the code init other
controller fields.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add #ifdef CONFIG_PM guard to fix build warning when !CONFIG_PM
drivers/spi/spi-fsl-lpspi.c:810:12: warning: ‘fsl_lpspi_runtime_suspend’ defined but not used [-Wunused-function]
static int fsl_lpspi_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/spi-fsl-lpspi.c:789:12: warning: ‘fsl_lpspi_runtime_resume’ defined but not used [-Wunused-function]
static int fsl_lpspi_runtime_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The original code already set controller as drvdata:
platform_set_drvdata(pdev, controller);
But commit 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
added dev_set_drvdata(&pdev->dev, fsl_lpspi);
so fsl_lpspi_remove() will get wrong pointer by platform_get_drvdata().
Fixes: 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function names in the kernel-doc comments were mistyped, with a word
"dirmap" being repeated twice, so fix them.
Fixes: aa167f3fed ("spi: spi-mem: Add a new API to support direct mapping")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When building CONFIG_DEBUG_FS is not set
gcc warn this:
drivers/spi/spi-bcm2835aux.c: In function bcm2835aux_spi_probe:
drivers/spi/spi-bcm2835aux.c:591:2: error: too many arguments to function bcm2835aux_debugfs_create
bcm2835aux_debugfs_create(bs, dev_name(&pdev->dev));
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/spi-bcm2835aux.c:145:13: note: declared here
static void bcm2835aux_debugfs_create(struct bcm2835aux_spi *bs)
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 8048d151eb ("spi: bcm2835aux: add driver stats to debugfs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'status' local variable is initialized but this value is never used,
thus kill that initializer.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for QSPI controller driver used by Xilinx Zynq SOC.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no code using 'pdev' field in struct spi_gpio. Drop it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The logic of setting mflags in spi_gpio_request() is very simple and
there isn't much benefit in having it in that function. Move all of
that code outside into spi_gpio_probe() in order to simplify things.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Move code calling spi_get_gpio_descs() to happen after ctlr->dev's
name is set in order to have proper GPIO consumer names.
Before:
cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 0-31, parent: platform/40049000.gpio, vf610-gpio:
gpio-6 ( |regulator-usb0-vbus ) out lo
gpiochip1: GPIOs 32-63, parent: platform/4004a000.gpio, vf610-gpio:
gpio-36 ( |scl ) in hi
gpio-37 ( |sda ) in hi
gpio-40 ( |(null) CS1 ) out lo
gpio-41 ( |(null) CS0 ) out lo ACTIVE LOW
gpio-42 ( |miso ) in hi
gpio-43 ( |mosi ) in lo
gpio-44 ( |sck ) out lo
After:
cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 0-31, parent: platform/40049000.gpio, vf610-gpio:
gpio-6 ( |regulator-usb0-vbus ) out lo
gpiochip1: GPIOs 32-63, parent: platform/4004a000.gpio, vf610-gpio:
gpio-36 ( |scl ) in hi
gpio-37 ( |sda ) in hi
gpio-40 ( |spi0 CS1 ) out lo
gpio-41 ( |spi0 CS0 ) out lo ACTIVE LOW
gpio-42 ( |miso ) in hi
gpio-43 ( |mosi ) in lo
gpio-44 ( |sck ) out lo
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
DT use-case already relies on SPI core to control CS (requested by
of_spi_register_master() and controlled spi_set_cs()), so there's no
need to try to request those GPIO in spi-gpio code. Change the code
such that spi-gpio's CS related code is only used if device is probed
via pdata.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch sets SPI device id from the device tree as the bus number.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Packed mode expects minimum transfer length of 4 bytes.
This patch fixes this by using unpacked mode for transfers less
than 4 bytes.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tegra SPI supports 4 through 32 bits per word.
This patch sets bits_per_word_mask accordingly to support transfer
with these bits per word.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch dumps SPI registers on transfer error or timeout for debug
purpose.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves SPI controller reset out of spin lock.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With SW CS, during the transfer completion CS is de-asserted by writing
default command1 register value to SPI_COMMAND1 register. With this both
mode and CS state are set at the same time and if current transfer mode
is different to default SPI mode and if mode change happens prior to CS
de-assert, clock polarity can change while CS is active before transfer
finishes.
This causes Slave to see spurious clock edges resulting in data mismatch.
This patch fixes this by de-asserting CS before writing SPI_COMMAND1 to
its default value so through out the transfer it will be in same SPI mode.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert GPIO chip selects in the Renesas MSIOF SPI driver from legacy
GPIO numbers to GPIO descriptors.
Notes:
- The board file for the SH7724-based Ecovec24 development board now
registers a GPIO descriptor lookup, instead of passing a GPIO number
through controller_data,
- sh_msiof_get_cs_gpios() must release all GPIOs, else
spi_get_gpio_descs() cannot claim them during SPI controller
registration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 5fd917afc4 ("spi: bcm2835aux: make the polling duration limits configurable")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While devm_gpiod_get_index_optional() returns NULL if the GPIO is not
present (i.e. -ENOENT), it may still return other error codes, like
-EPROBE_DEFER. Currently these are not handled, leading to
unrecoverable failures later in case of probe deferral:
gpiod_set_consumer_name: invalid GPIO (errorpointer)
gpiod_direction_output: invalid GPIO (errorpointer)
gpiod_set_value_cansleep: invalid GPIO (errorpointer)
gpiod_set_value_cansleep: invalid GPIO (errorpointer)
gpiod_set_value_cansleep: invalid GPIO (errorpointer)
Detect and propagate errors to fix this.
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion from GPIO numbers to GPIO descriptors removed the use of
spi->controller_data, but forgot to update a comment referring to it.
Fixes: 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
To estimate efficiency add statistics on transfer types
(polling and interrupt) used to debugfs.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In accordance with hardware specification Ver 1.0, reset register
transmission / reception setting before transfer.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: Use readl_poll_timeout_atomic()]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the open-coded loop in sh_msiof_modify_ctr_wait() by a call to
the readl_poll_timeout_atomic() helper macro.
Suggested-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing complete operations for dma_completion to fix the
problem of blocking at the wait_for_completion_interruptible()
function when use spi_slave_abort().
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop unused pdata copy in struct spi_gpio. No functional change
intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Swap branches of the if statement in order to simplify it's logical
condition being checked. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a local "struct spi_bitbang *bb" in spi_gpio_probe() for
brevity. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a local "struct device *dev" in spi_gpio_probe() for brevity. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
