Merge L1 Terminal Fault fixes from Thomas Gleixner:
"L1TF, aka L1 Terminal Fault, is yet another speculative hardware
engineering trainwreck. It's a hardware vulnerability which allows
unprivileged speculative access to data which is available in the
Level 1 Data Cache when the page table entry controlling the virtual
address, which is used for the access, has the Present bit cleared or
other reserved bits set.
If an instruction accesses a virtual address for which the relevant
page table entry (PTE) has the Present bit cleared or other reserved
bits set, then speculative execution ignores the invalid PTE and loads
the referenced data if it is present in the Level 1 Data Cache, as if
the page referenced by the address bits in the PTE was still present
and accessible.
While this is a purely speculative mechanism and the instruction will
raise a page fault when it is retired eventually, the pure act of
loading the data and making it available to other speculative
instructions opens up the opportunity for side channel attacks to
unprivileged malicious code, similar to the Meltdown attack.
While Meltdown breaks the user space to kernel space protection, L1TF
allows to attack any physical memory address in the system and the
attack works across all protection domains. It allows an attack of SGX
and also works from inside virtual machines because the speculation
bypasses the extended page table (EPT) protection mechanism.
The assoicated CVEs are: CVE-2018-3615, CVE-2018-3620, CVE-2018-3646
The mitigations provided by this pull request include:
- Host side protection by inverting the upper address bits of a non
present page table entry so the entry points to uncacheable memory.
- Hypervisor protection by flushing L1 Data Cache on VMENTER.
- SMT (HyperThreading) control knobs, which allow to 'turn off' SMT
by offlining the sibling CPU threads. The knobs are available on
the kernel command line and at runtime via sysfs
- Control knobs for the hypervisor mitigation, related to L1D flush
and SMT control. The knobs are available on the kernel command line
and at runtime via sysfs
- Extensive documentation about L1TF including various degrees of
mitigations.
Thanks to all people who have contributed to this in various ways -
patches, review, testing, backporting - and the fruitful, sometimes
heated, but at the end constructive discussions.
There is work in progress to provide other forms of mitigations, which
might be less horrible performance wise for a particular kind of
workloads, but this is not yet ready for consumption due to their
complexity and limitations"
* 'l1tf-final' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (75 commits)
x86/microcode: Allow late microcode loading with SMT disabled
tools headers: Synchronise x86 cpufeatures.h for L1TF additions
x86/mm/kmmio: Make the tracer robust against L1TF
x86/mm/pat: Make set_memory_np() L1TF safe
x86/speculation/l1tf: Make pmd/pud_mknotpresent() invert
x86/speculation/l1tf: Invert all not present mappings
cpu/hotplug: Fix SMT supported evaluation
KVM: VMX: Tell the nested hypervisor to skip L1D flush on vmentry
x86/speculation: Use ARCH_CAPABILITIES to skip L1D flush on vmentry
x86/speculation: Simplify sysfs report of VMX L1TF vulnerability
Documentation/l1tf: Remove Yonah processors from not vulnerable list
x86/KVM/VMX: Don't set l1tf_flush_l1d from vmx_handle_external_intr()
x86/irq: Let interrupt handlers set kvm_cpu_l1tf_flush_l1d
x86: Don't include linux/irq.h from asm/hardirq.h
x86/KVM/VMX: Introduce per-host-cpu analogue of l1tf_flush_l1d
x86/irq: Demote irq_cpustat_t::__softirq_pending to u16
x86/KVM/VMX: Move the l1tf_flush_l1d test to vmx_l1d_flush()
x86/KVM/VMX: Replace 'vmx_l1d_flush_always' with 'vmx_l1d_flush_cond'
x86/KVM/VMX: Don't set l1tf_flush_l1d to true from vmx_l1d_flush()
cpu/hotplug: detect SMT disabled by BIOS
...
Pull x86 apic update from Thomas Gleixner:
"Trivial cleanups of the APIC related code"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Trivial coding style fixes
x86/vector: Merge allocate_vector() into assign_vector_locked()
The next patch in this series will have to make the definition of
irq_cpustat_t available to entering_irq().
Inclusion of asm/hardirq.h into asm/apic.h would cause circular header
dependencies like
asm/smp.h
asm/apic.h
asm/hardirq.h
linux/irq.h
linux/topology.h
linux/smp.h
asm/smp.h
or
linux/gfp.h
linux/mmzone.h
asm/mmzone.h
asm/mmzone_64.h
asm/smp.h
asm/apic.h
asm/hardirq.h
linux/irq.h
linux/irqdesc.h
linux/kobject.h
linux/sysfs.h
linux/kernfs.h
linux/idr.h
linux/gfp.h
and others.
This causes compilation errors because of the header guards becoming
effective in the second inclusion: symbols/macros that had been defined
before wouldn't be available to intermediate headers in the #include chain
anymore.
A possible workaround would be to move the definition of irq_cpustat_t
into its own header and include that from both, asm/hardirq.h and
asm/apic.h.
However, this wouldn't solve the real problem, namely asm/harirq.h
unnecessarily pulling in all the linux/irq.h cruft: nothing in
asm/hardirq.h itself requires it. Also, note that there are some other
archs, like e.g. arm64, which don't have that #include in their
asm/hardirq.h.
Remove the linux/irq.h #include from x86' asm/hardirq.h.
Fix resulting compilation errors by adding appropriate #includes to *.c
files as needed.
Note that some of these *.c files could be cleaned up a bit wrt. to their
set of #includes, but that should better be done from separate patches, if
at all.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Extend the debugability of the vector management by adding the state bits
to the debugfs output.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Song Liu <songliubraving@fb.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <liu.song.a23@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tariq Toukan <tariqt@mellanox.com>
Link: https://lkml.kernel.org/r/20180604162224.908136099@linutronix.de
apic_ack_edge() is explicitely for handling interrupt affinity cleanup when
interrupt remapping is not available or disable.
Remapped interrupts and also some of the platform specific special
interrupts, e.g. UV, invoke ack_APIC_irq() directly.
To address the issue of failing an affinity update with -EBUSY the delayed
affinity mechanism can be reused, but ack_APIC_irq() does not handle
that. Adding this to ack_APIC_irq() is not possible, because that function
is also used for exceptions and directly handled interrupts like IPIs.
Create a new function, which just contains the conditional invocation of
irq_move_irq() and the final ack_APIC_irq().
Reuse the new function in apic_ack_edge().
Preparatory change for the real fix.
Fixes: dccfe3147b ("x86/vector: Simplify vector move cleanup")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Song Liu <songliubraving@fb.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <liu.song.a23@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: stable@vger.kernel.org
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tariq Toukan <tariqt@mellanox.com>
Link: https://lkml.kernel.org/r/20180604162224.471925894@linutronix.de
Several people observed the WARN_ON() in irq_matrix_free() which triggers
when the caller tries to free an vector which is not in the allocation
range. Song provided the trace information which allowed to decode the root
cause.
The rework of the vector allocation mechanism failed to preserve a sanity
check, which prevents setting a new target vector/CPU when the previous
affinity change has not fully completed.
As a result a half finished affinity change can be overwritten, which can
cause the leak of a irq descriptor pointer on the previous target CPU and
double enqueue of the hlist head into the cleanup lists of two or more
CPUs. After one CPU cleaned up its vector the next CPU will invoke the
cleanup handler with vector 0, which triggers the out of range warning in
the matrix allocator.
Prevent this by checking the apic_data of the interrupt whether the
move_in_progress flag is false and the hlist node is not hashed. Return
-EBUSY if not.
This prevents the damage and restores the behaviour before the vector
allocation rework, but due to other changes in that area it also widens the
chance that user space can observe -EBUSY. In theory this should be fine,
but actually not all user space tools handle -EBUSY correctly. Addressing
that is not part of this fix, but will be addressed in follow up patches.
Fixes: 69cde0004a ("x86/vector: Use matrix allocator for vector assignment")
Reported-by: Dmitry Safonov <0x7f454c46@gmail.com>
Reported-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Song Liu <liu.song.a23@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Song Liu <songliubraving@fb.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/20180604162224.303870257@linutronix.de
assign_vector_locked() calls allocate_vector() to get a real vector for an
IRQ. If the current target CPU is online and in the new requested affinity
mask, allocate_vector() will return 0 and nothing should be done. But,
assign_vector_locked() calls apic_update_irq_cfg() even in that case which
is pointless.
allocate_vector() is not called from anything else, so the functions can be
merged and in case of no change the apic_update_irq_cfg() can be avoided.
[ tglx: Massaged changelog ]
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/20180511080956.6316-1-douly.fnst@cn.fujitsu.com
When a irq vector is replaced, then the previous vector is normally
released when the first interrupt happens on the new vector. If the target
CPU of the previous vector is already offline when the new vector is
installed, then the previous vector is silently discarded, which leads to
accounting issues causing suspend failures and other problems.
Adjust the logic so that the previous vector is freed in the underlying
matrix allocator to ensure that the accounting stays correct.
Fixes: 69cde0004a ("x86/vector: Use matrix allocator for vector assignment")
Reported-by: Yuriy Vostrikov <delamonpansie@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Yuriy Vostrikov <delamonpansie@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180222112316.930791749@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Keith reported the following warning:
WARNING: CPU: 28 PID: 1420 at kernel/irq/matrix.c:222 irq_matrix_remove_managed+0x10f/0x120
x86_vector_free_irqs+0xa1/0x180
x86_vector_alloc_irqs+0x1e4/0x3a0
msi_domain_alloc+0x62/0x130
The reason for this is that if the vector allocation fails the error
handling code tries to free the failed vector as well, which causes the
above imbalance warning to trigger.
Adjust the error path to handle this correctly.
Fixes: b5dc8e6c21 ("x86/irq: Use hierarchical irqdomain to manage CPU interrupt vectors")
Reported-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Keith Busch <keith.busch@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1801161217300.1823@nanos
The new reservation mode for interrupts assigns a dummy vector when the
interrupt is allocated and assigns a real vector when the interrupt is
requested. The reservation mode prevents vector pressure when devices with
a large amount of queues/interrupts are initialized, but only a minimal
subset of those queues/interrupts is actually used.
This mode has an issue with MSI interrupts which cannot be masked. If the
driver is not careful or the hardware emits an interrupt before the device
irq is requestd by the driver then the interrupt ends up on the dummy
vector as a spurious interrupt which can cause malfunction of the device or
in the worst case a lockup of the machine.
Change the logic for the reservation mode so that the early activation of
MSI interrupts checks whether:
- the device is a PCI/MSI device
- the reservation mode of the underlying irqdomain is activated
- PCI/MSI masking is globally enabled
- the PCI/MSI device uses either MSI-X, which supports masking, or
MSI with the maskbit supported.
If one of those conditions is false, then clear the reservation mode flag
in the irq data of the interrupt and invoke irq_domain_activate_irq() with
the reserve argument cleared. In the x86 vector code, clear the can_reserve
flag in the vector allocation data so a subsequent free_irq() won't create
the same situation again. The interrupt stays assigned to a real vector
until pci_disable_msi() is invoked and all allocations are undone.
Fixes: 4900be8360 ("x86/vector/msi: Switch to global reservation mode")
Reported-by: Alexandru Chirvasitu <achirvasub@gmail.com>
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandru Chirvasitu <achirvasub@gmail.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712291406420.1899@nanos
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712291409460.1899@nanos
The 'early' argument of irq_domain_activate_irq() is actually used to
denote reservation mode. To avoid confusion, rename it before abuse
happens.
No functional change.
Fixes: 7249164346 ("genirq/irqdomain: Update irq_domain_ops.activate() signature")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexandru Chirvasitu <achirvasub@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
Set the new CAN_RESERVE flag when the initial reservation for an interrupt
happens. The flag is used in a subsequent patch to disable reservation mode
for a certain class of MSI devices.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandru Chirvasitu <achirvasub@gmail.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
Functions x86_vector_debug_show(), uv_handle_nmi() and uv_nmi_setup_common()
are local to the source and do not need to be in global scope, so make them
static.
Fixes up various sparse warnings.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Mike Travis <mike.travis@hpe.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russ Anderson <russ.anderson@hpe.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-janitors@vger.kernel.org
Cc: travis@sgi.com
Link: http://lkml.kernel.org/r/20171206173358.24388-1-colin.king@canonical.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There are no in-tree callers of ht_create_irq(), the driver interface for
HyperTransport interrupts, left. Remove the unused entry point and all the
supporting code.
See 8b955b0ddd ("[PATCH] Initial generic hypertransport interrupt
support").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pci@vger.kernel.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: https://lkml.kernel.org/r/20171122221337.3877.23362.stgit@bhelgaas-glaptop.roam.corp.google.com
free_moved_vector() accesses the per cpu vector array with this_cpu_write()
to clear the vector. The function has two call sites:
1) The vector cleanup IPI
2) The force_complete_move() code path
For #1 this_cpu_write() is correct as it runs on the CPU on which the
vector needs to be freed.
For #2 this_cpu_write() is wrong because the function is called from an
outgoing CPU which is not necessarily the CPU on which the previous vector
needs to be freed. As a result it sets the vector on the outgoing CPU to
NULL, which is pointless as that CPU does not handle interrupts
anymore. What's worse is that it leaves the vector on the previous target
CPU in place which later on triggers the BUG_ON(vector) in the vector
allocation code when the vector gets reused. That's possible because the
bitmap allocator entry of that CPU is freed correctly.
Always use the CPU to which the vector was associated and clear the vector
entry on that CPU. Fixup the tracepoint as well so it tracks on which CPU
the vector gets removed.
Fixes: 69cde0004a ("x86/vector: Use matrix allocator for vector assignment")
Reported-by: Petri Latvala <petri.latvala@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Yu Chen <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1710161614430.1973@nanos
The core interrupt code can call the affinity setter for inactive
interrupts under certain circumstances.
For inactive intererupts which use managed or reservation mode this is a
pointless exercise as the activation will assign a vector which fits the
destination mask.
Check for this and return w/o going through the vector assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The interrupt descriptor has a preset affinity mask at allocation
time, which is usually the default affinity mask.
The current code does not respect that mask and places the vector at some
random CPU, which gets corrected later by a set_affinity() call. That's
silly because the vector allocation can respect the mask upfront and place
the interrupt on a CPU which is in the mask. If that fails, then the
affinity is broken and a interrupt assigned on any online CPU.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213156.431670325@linutronix.de
Before a CPU is taken offline the number of active interrupt vectors on the
outgoing CPU and the number of vectors which are available on the other
online CPUs are counted and compared. If the active vectors are more than
the available vectors on the other CPUs then the CPU hot-unplug operation
is aborted. This again uses loop based search and is inaccurate.
The bitmap matrix allocator has accurate accounting information and can
tell exactly whether the vector space is sufficient or not.
Emit a message when the number of globaly reserved (unallocated) vectors is
larger than the number of available vectors after offlining a CPU because
after that point request_irq() might fail.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213156.351193962@linutronix.de
IOAPICs install and allocate vectors for inactive interrupts. This results
in problems on CPU offline and wastes vector resources for nothing.
Handle inactive IOAPIC interrupts in the same way as inactive MSI
interrupts and switch them to the global reservation mode.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213156.273454591@linutronix.de
Devices with many queues allocate a huge number of interrupts and get
assigned a vector for each of them, even if the queues are not active and
the interrupts never requested. This causes problems with the decision
whether the global vector space is sufficient for CPU hot unplug
operations.
Change it to a reservation scheme, which allows overcommitment.
When the interrupt is allocated and initialized the vector assignment
merily updates the reservation request counter in the matrix
allocator. This counter is used to emit warnings when the reservation
exceeds the available vector space, but does not affect CPU offline
operations. Like the managed interrupts the corresponding MSI/DMAR/IOAPIC
entries are directed to the special shutdown vector.
When the interrupt is requested, then the activation code tries to assign a
real vector. If that succeeds the interrupt is started up and functional.
If that fails, then subsequently request_irq() fails with -ENOSPC.
This allows a clear separation of inactive and active modes and simplifies
the final decisions whether the global vector space is sufficient for CPU
offline operations.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213156.184211133@linutronix.de
Managed interrupts need to reserve interrupt vectors permanently, but as
long as the interrupt is deactivated, the vector should not be active.
Reserve a new system vector, which can be used to initially initialize
MSI/DMAR/IOAPIC entries. In that situation the interrupts are disabled in
the corresponding MSI/DMAR/IOAPIC devices. So the vector should never be
sent to any CPU.
When the managed interrupt is started up, a real vector is assigned from
the managed vector space and configured in MSI/DMAR/IOAPIC.
This allows a clear separation of inactive and active modes and simplifies
the final decisions whether the global vector space is sufficient for CPU
offline operations.
The vector space can be reserved even on offline CPUs and will survive CPU
offline/online operations.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213156.104616625@linutronix.de
The vector management state is not required to live in irq_cfg. irq_cfg is
only relevant for the depending irq domains (IOAPIC, DMAR, MSI ...).
The seperation of the vector management status allows to direct a shut down
interrupt to a special shutdown vector w/o confusing the internal state of
the vector management.
Preparatory change for the rework of managed interrupts and the global
vector reservation scheme.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213155.683712356@linutronix.de
No point in compiling this for UP.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213155.603191841@linutronix.de
Replace the magic vector allocation code by a simple bitmap matrix
allocator. This avoids loops and hoops over CPUs and vector arrays, so in
case of densly used vector spaces it's way faster.
This also gets rid of the magic 'spread the vectors accross priority
levels' heuristics in the current allocator:
The comment in __asign_irq_vector says:
* NOTE! The local APIC isn't very good at handling
* multiple interrupts at the same interrupt level.
* As the interrupt level is determined by taking the
* vector number and shifting that right by 4, we
* want to spread these out a bit so that they don't
* all fall in the same interrupt level.
After doing some palaeontological research the following was found the
following in the PPro Developer Manual Volume 3:
"7.4.2. Valid Interrupts
The local and I/O APICs support 240 distinct vectors in the range of 16
to 255. Interrupt priority is implied by its vector, according to the
following relationship: priority = vector / 16
One is the lowest priority and 15 is the highest. Vectors 16 through
31 are reserved for exclusive use by the processor. The remaining
vectors are for general use. The processor's local APIC includes an
in-service entry and a holding entry for each priority level. To avoid
losing inter- rupts, software should allocate no more than 2 interrupt
vectors per priority."
The current SDM tells nothing about that, instead it states:
"If more than one interrupt is generated with the same vector number,
the local APIC can set the bit for the vector both in the IRR and the
ISR. This means that for the Pentium 4 and Intel Xeon processors, the
IRR and ISR can queue two interrupts for each interrupt vector: one
in the IRR and one in the ISR. Any additional interrupts issued for
the same interrupt vector are collapsed into the single bit in the
IRR.
For the P6 family and Pentium processors, the IRR and ISR registers
can queue no more than two interrupts per interrupt vector and will
reject other interrupts that are received within the same vector."
Which means, that on P6/Pentium the APIC will reject a new message and
tell the sender to retry, which increases the load on the APIC bus and
nothing more.
There is no affirmative answer from Intel on that, but it's a sane approach
to remove that for the following reasons:
1) No other (relevant Open Source) operating systems bothers to
implement this or mentiones this at all.
2) The current allocator has no enforcement for this and especially the
legacy interrupts, which are the main source of interrupts on these
P6 and older systmes, are allocated linearly in the same priority
level and just work.
3) The current machines have no problem with that at all as verified
with some experiments.
4) AMD at least confirmed that such an issue is unknown.
5) P6 and older are dinosaurs almost 20 years EOL, so there is really
no reason to worry about that too much.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213155.443678104@linutronix.de
Add tracepoints for analysing the new vector management
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213155.357986795@linutronix.de
Add the debug callback for the vector domain, which gives a detailed
information about vector usage if invoked for the domain by using rhe
matrix allocator debug function and vector/target information when invoked
for a particular interrupt.
Extra information foir the Vector domain:
Online bitmaps: 32
Global available: 6352
Global reserved: 5
Total allocated: 20
System: 41: 0-19,32,50,128,238-255
| CPU | avl | man | act | vectors
0 183 4 19 33-48,51-53
1 199 4 1 33
2 199 4 0
Extra information for interrupts:
Vector: 42
Target: 4
This allows a detailed analysis of the vector usage and the association to
interrupts and devices.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213155.188137174@linutronix.de
Initialize the matrix allocator and add the proper accounting points to the
code.
No functional change, just preparation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213155.108410660@linutronix.de
Move the helper functions to a different place as they would end up in the
middle of management functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213154.949581934@linutronix.de
The info pointer checks in assign_irq_vector_policy() are pointless because
the pointer cannot be NULL, otherwise the calling code would already crash.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213154.859484148@linutronix.de
Now that the legacy PIC takeover by the IOAPIC is marked accordingly the
early boot allocation of APIC data is not longer necessary. Use the regular
allocation mechansim as it is used by non legacy interrupts and fill in the
known information (vector and affinity) so the allocator reuses the vector,
This is important as the timer check might move the timer interrupt 0 back
to the PIC in case the delivery through the IOAPIC fails.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213154.780521549@linutronix.de
The vector move cleanup needs to walk the vector space and do a lot of
sanity checks to find a vector to cleanup.
With single CPU affinities this can be simplified and made more robust by
queueing the vector configuration which needs to be cleaned up in a hlist
on the CPU which was the previous target.
That removes all the race conditions because the cleanup either finds a
valid list entry or not. The latter happens when the interrupt was torn
down before the cleanup handler was able to run.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213154.622727892@linutronix.de
Now that the interrupt affinities are targeted at single CPUs storing them
in a cpumask is overkill. Store them in a dedicated variable.
This does not yet remove the domain cpumasks because the current allocator
relies on them. Preparatory change for the allocator rework.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213154.544867277@linutronix.de
The naming convention of variables with the types irq_data and
apic_chip_data are inconsistent and confusing.
Before reworking the whole vector management make them consistent so
irq_data pointers are named 'irqd' and apic_chip_data are named 'apicd' all
over the place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213154.465731667@linutronix.de
With single CPU affinities it's not longer required to scan all interrupts
for potential destination masks which contain the newly booting CPU.
Reduce it to install the active legacy PIC vectors on the newly booting CPU
as those cannot be affinity controlled by the kernel and potentially end up
at any CPU in the system.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213154.388040204@linutronix.de
Setting the interrupt affinity of a single interrupt to multiple CPUs has a
dubious value.
1) This only works on machines where the APIC uses logical destination
mode. If the APIC uses physical destination mode then it is already
restricted to a single CPU
2) Experiments have shown, that the benefit of multi CPU affinity is close
to zero and in some test even worse than setting the affinity to a
single CPU.
The reason for this is that the delivery targets the APIC with the
lowest ID first and only if that APIC is busy (servicing an interrupt,
i.e. ISR is not empty) it hands it over to the next APIC. In the
conducted tests the vast majority of interrupts ends up on the APIC
with the lowest ID anyway, so there is no natural spreading of the
interrupts possible.
Supporting multi CPU affinities adds a lot of complexity to the code, which
can turn the allocation search into a worst case of
nr_vectors * nr_online_cpus * nr_bits_in_target_mask
As a first step disable it by restricting the vector search to a single
CPU.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213154.228824430@linutronix.de
used_vectors is a nisnomer as it only has the system vectors which are
excluded from the regular vector allocation marked. It's not what the name
suggests storage for the actually used vectors.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213154.150209009@linutronix.de
The target_cpus() callback of the apic struct is not really useful. Some
APICs return cpu_online_mask and others cpus_all_mask. The latter is bogus
as it does not take holes in the cpus_possible_mask into account.
Replace it with cpus_online_mask which makes the most sense and remove the
callback.
The usage sites will be removed in a later step anyway, so get rid of it
now to have incremental changes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213154.070850916@linutronix.de
This variable is beyond pointless. Nothing allocates a vector via
alloc_gate() below FIRST_SYSTEM_VECTOR. So nothing can change
first_system_vector.
If there is a need for a gate below FIRST_SYSTEM_VECTOR then it can be
added to the vector defines and FIRST_SYSTEM_VECTOR can be adjusted
accordingly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170828064956.357109735@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull irq updates from Thomas Gleixner:
"The irq department delivers:
- Expand the generic infrastructure handling the irq migration on CPU
hotplug and convert X86 over to it. (Thomas Gleixner)
Aside of consolidating code this is a preparatory change for:
- Finalizing the affinity management for multi-queue devices. The
main change here is to shut down interrupts which are affine to a
outgoing CPU and reenabling them when the CPU comes online again.
That avoids moving interrupts pointlessly around and breaking and
reestablishing affinities for no value. (Christoph Hellwig)
Note: This contains also the BLOCK-MQ and NVME changes which depend
on the rework of the irq core infrastructure. Jens acked them and
agreed that they should go with the irq changes.
- Consolidation of irq domain code (Marc Zyngier)
- State tracking consolidation in the core code (Jeffy Chen)
- Add debug infrastructure for hierarchical irq domains (Thomas
Gleixner)
- Infrastructure enhancement for managing generic interrupt chips via
devmem (Bartosz Golaszewski)
- Constification work all over the place (Tobias Klauser)
- Two new interrupt controller drivers for MVEBU (Thomas Petazzoni)
- The usual set of fixes, updates and enhancements all over the
place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (112 commits)
irqchip/or1k-pic: Fix interrupt acknowledgement
irqchip/irq-mvebu-gicp: Allocate enough memory for spi_bitmap
irqchip/gic-v3: Fix out-of-bound access in gic_set_affinity
nvme: Allocate queues for all possible CPUs
blk-mq: Create hctx for each present CPU
blk-mq: Include all present CPUs in the default queue mapping
genirq: Avoid unnecessary low level irq function calls
genirq: Set irq masked state when initializing irq_desc
genirq/timings: Add infrastructure for estimating the next interrupt arrival time
genirq/timings: Add infrastructure to track the interrupt timings
genirq/debugfs: Remove pointless NULL pointer check
irqchip/gic-v3-its: Don't assume GICv3 hardware supports 16bit INTID
irqchip/gic-v3-its: Add ACPI NUMA node mapping
irqchip/gic-v3-its-platform-msi: Make of_device_ids const
irqchip/gic-v3-its: Make of_device_ids const
irqchip/irq-mvebu-icu: Add new driver for Marvell ICU
irqchip/irq-mvebu-gicp: Add new driver for Marvell GICP
dt-bindings/interrupt-controller: Add DT binding for the Marvell ICU
genirq/irqdomain: Remove auto-recursive hierarchy support
irqchip/MSI: Use irq_domain_update_bus_token instead of an open coded access
...
If the interrupt destination mode of the APIC is physical then the
effective affinity is restricted to a single CPU.
Mark the interrupt accordingly in the domain allocation code, so the core
code can avoid pointless affinity setting attempts.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235447.508846202@linutronix.de
The decision to which CPUs an interrupt is effectively routed happens in
the various apic->cpu_mask_to_apicid() implementations
To support effective affinity masks this information needs to be updated in
irq_data. Add a pointer to irq_data to the callbacks and feed it through
the call chain.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.720739075@linutronix.de
All implementations of apic->cpu_mask_to_apicid_and() and the two incoming
cpumasks to search for the target.
Move that operation to the call site and rename it to cpu_mask_to_apicid()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.641575516@linutronix.de
All implementations of apic->cpu_mask_to_apicid_and() mask out the offline
cpus. The callsite already has a mask available, which has the offline CPUs
removed. Use that and remove the extra bits.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235446.560868224@linutronix.de
Use the fwnode to create a named domain so diagnosis works.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235443.673635238@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add the missing name, so debugging will work proper.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235443.266561988@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This function is only called by arch_early_irq_init(), which is an
__init function, so mark the child function __init as well.
In addition mark it inline for the !CONFIG_X86_IO_APIC case.
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1498040061-5332-1-git-send-email-douly.fnst@cn.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When a CPU is about to be offlined we call fixup_irqs() that resets IRQ
affinities related to the CPU in question. The same thing is also done when
the system is suspended to S-states like S3 (mem).
For each IRQ we try to complete any on-going move regardless whether the
IRQ is actually part of x86_vector_domain. For each IRQ descriptor we fetch
its chip_data, assume it is of type struct apic_chip_data and manipulate it
by clearing old_domain mask etc. For irq_chips that are not part of the
x86_vector_domain, like those created by various GPIO drivers, will find
their chip_data being changed unexpectly.
Below is an example where GPIO chip owned by pinctrl-sunrisepoint.c gets
corrupted after resume:
# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 360-511, parent: platform/INT344B:00, INT344B:00:
gpio-511 ( |sysfs ) in hi
# rtcwake -s10 -mmem
<10 seconds passes>
# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 360-511, parent: platform/INT344B:00, INT344B:00:
gpio-511 ( |sysfs ) in ?
Note '?' in the output. It means the struct gpio_chip ->get function is
NULL whereas before suspend it was there.
Fix this by first checking that the IRQ belongs to x86_vector_domain before
we try to use the chip_data as struct apic_chip_data.
Reported-and-tested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org # 4.4+
Link: http://lkml.kernel.org/r/20161003101708.34795-1-mika.westerberg@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
