The function can return negative values in case of error.
Its result should be then tested for such case.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For devices that does not support PCI power save, force wake up
API is used. So move powersave check inside force wakeup to reduce
one level indentation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 1aaf8efba0 ("ath10k: disable PCI PS for QCA988X
and QCA99X0") partially reverts pci soc powersave support added by
commit 77258d409c ("ath10k: enable pci soc powersaving"). While
reverting the change, pci wake up function is called after accessing
pci registers instead of prior to access. The assumption is that chip
is woken up before accessing its registers.Though this change does not
fix any known issues, this might help to avoid unknown or low power
platform specific issues.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Mesh Point requires peer security key install when running
in secured mode since it's a type of peer links, otherwise peer
link will be removed due to key install failure.
MFP feature set is required to run Mesh in secured mode and
QCA988X firmware, 10.2.4.70.14-2 and above, is the only one
supporting secured Mesh at this moment.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch is derived from
commit 6301566e0b ("ath9k: export HW random number generator"),
We evaluated the entropy of the ADC data on QCA9531, QCA9561, QCA955x,
and AR9340, and it has sufficient quality random data (at least 10 bits
and up to 22 bits of min-entropy for a 32-bit value). We conservatively
assume the min-entropy is 10 bits out of 32 bits. Thus, ATH9K_RNG_BUF_SIZE
is set to 320 (u32) i.e., 1.25 kilobytes of data is inserted to fill up
the pool as soon as the entropy counter becomes 896/4096 (set by random.c).
Since ADC was not designed to be a dedicated HW RNG, we do not want to bind
it to /dev/hwrng framework directly. This patch feeds the entropy directly
from the WiFi driver to the input pool. The ADC register output is only
used as a seed for the Linux entropy pool. No conditioning is needed,
since all the conditioning is performed by the pool itself.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When rx stopped, AR_RX_FILTER should be cleared, but in
ath9k_hw_setrxfilter(), ATH9K_RX_FILTER_CONTROL_WRAPPER will always
be set for ar9462/ar9565.
Fix this by moving the code in ath9k_hw_setrxfilter() to
ath_calcrxfilter().
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This gives a user a chance to know why a firmware load
is failing.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
My previous patch incorrectly reported the antenna
for 2x2 devices. It should be a mask instead of
a numeric count. This patch fixes that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* support bcm4359 which can operate in two bands concurrently
* disable runtime pm for USB avoiding issues
* use generic pm callback in PCIe driver
* support wowlan wake indication reporting
* add beamforming support
* unified handling of firmware files
ath10k
* support Manegement Frame Protection (MFP)
* add thermal throttling support for 10.4 firmware
* add support for pktlog in QCA99X0
* add debugfs file to enable Bluetooth coexistence feature
* use firmware's native mesh interface type instead of raw mode
iwlwifi
* BT coex improvements
* D3 operation bugfixes
* rate control improvements
* firmware debugging infra improvements
* ground work for multi Rx
* various security fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWZcQtAAoJEG4XJFUm622bgcMH/1VRwtzAKpYVwAyAN0MtVLxe
uANi0Pw1PmEAeEI3TxEBckEH0JYfpg+aAwX7S8scnQSvLP3FYeC5IcHG551vlh0s
FlkGexcXqGrDqjt8mz8hxqqAmMH9YEVlzj2HJf6YFjNS4K84CEgpaSjaSG8S7Wc8
hTSA5K+XxrnEeX41W7FYmeBFLejisg0gVTkS3ZCe4qYz4Gh1oamoA0pOdU+AYOMy
0XBkCT8fqTVXWLHh9/+J7IZOYrjBl4rVaHofeygEAfSRNNfmmjZXX1R+FCQoJEZC
IOEQ31T64G4A37t2N2RGOhiG+2vckdbPg2JsqJosI1L2OZSBbeGZsVW48w+5cgc=
=GQDA
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Vallo says:
====================
brcfmac
* support bcm4359 which can operate in two bands concurrently
* disable runtime pm for USB avoiding issues
* use generic pm callback in PCIe driver
* support wowlan wake indication reporting
* add beamforming support
* unified handling of firmware files
ath10k
* support Manegement Frame Protection (MFP)
* add thermal throttling support for 10.4 firmware
* add support for pktlog in QCA99X0
* add debugfs file to enable Bluetooth coexistence feature
* use firmware's native mesh interface type instead of raw mode
iwlwifi
* BT coex improvements
* D3 operation bugfixes
* rate control improvements
* firmware debugging infra improvements
* ground work for multi Rx
* various security fixes
====================
Conflicts:
drivers/net/wireless/ath/ath10k/pci.c
The conflict resolution at:
http://article.gmane.org/gmane.linux.kernel.next/37391
by Stephen Rothwell was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ath9k_mod_tsf64_tu() function while we could
use div_u64_rem() function.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is useful for MCC debugging and bug fixing.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of MCC and AP interface, add also NOA attr
that will inform stations about absence of an AP.
There is a chance that some stations will handle
this NOA attr correctly and will know exactly when
AP is present/absent.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case we get BSS_CHANGED_P2P_PS early, from
mac80211, we didn't set NOA timer correctly,
while p2p_ps_vif was NULL.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When adding NOA attr enable Opportunistic Power Save.
Before we calculate ctwindow but didn't enable oppps.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After queue nullfunc for MCC case, we hit WARN_ON
in xmit.c:2398 while skb priority wasn't set.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use u32 while ath9k_hw_gettsf32() and
ath9k_hw_gen_timer_start() require u32.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AP/GO will aprear after NOA, wait 1ms to be sure AP
could receive/answer this frames.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While mac80211 using null frames when connection polling,
we should queue this frames while NOA could be there, and
AP, P2P_GO could be not present.
Without this patch, with no traffic we often saw disconnections
while we try to send nullfunc when AP/GO wasn't present.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of low HZ before this patch we saw wrong
values in debug message. Print real timeout value.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add/extend debug messages when chanctx used.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In __wmi_send we check if fw is ready at the beginning of the function.
While we wait for the completion of the previous command, system suspend
can be invoked and reset the HW, causing __wmi_send to read from HW
registers while it is not ready.
Taking the wmi_mutex in the reset flow when setting the FW ready bit
to zero will prevent the above race condition.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The rates in the tx control rateset do not have the protection
flags applied, so RTS/CTS would never get enabled if requested.
Fix by using the rate flags in the rates returned by
ieee80211_get_tx_rates().
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
An error message ath6kl_htc_rxmsg_pending_handler isn't appropate for when
the error is ECANCELED. This could be the result of a perfectly appropriate
RX cancel due to shutdown or suspend. This allows the right cleanup to
continue, but without an alarming error message in this particular case.
Signed-off-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The three eeprom implementations had quite some duplicate code when it
came to endianness swapping.
Additionally there was a bug in eeprom_4k and eeprom_9287 which
prevented the endianness swapping from working correctly, because the
swapping code was guarded within an "if (!ath9k_hw_use_flash(ah))". In
eeprom_def this check did not exist, so it seems that eeprom_def was the
only implementation where endianness swapping worked.
This patch takes the duplicate code and moves it from eeprom_* to
eeprom.c. The new code is derived from eeprom_def, while taking into
account the specifics from the other implementations.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Coherent memory is more expensive to allocate (and constrained on some
architectures where it has to be pre-allocated). It is also completely
unnecessary, since the host has no reason to even access these allocated
memory spaces
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The default values of max_num_amsdu / max_num_amdpu is assigned a
default value as part of 'ath10k_core_init_firmware_features'
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
ath10k
* support Manegement Frame Protection (MFP)
* add thermal throttling support for 10.4 firmware
* add support for pktlog in QCA99X0
* add debugfs file to enable Bluetooth coexistence feature
* use firmware's native mesh interface type instead of raw mode
When debugging firmware problems it's useful to check checksums of each
component. Add a debugfs interface to retrieve crc32 checksums:
# cat /sys/kernel/debug/ieee80211/phy0/ath10k/fw_checksums
firmware-N.bin cc3fb466
athwlan c0089f21
otp f3efeb4f
codeswap 00000000
board-N.bin bebc7c08
board bebc7c08
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Earlier we printed all the info messages after a successful device
initialisation and firmware boot, but that's problematic if something goes
wrong and there's no easy way to know what firmware version was used and so on.
Split the info messages into smaller pieces and print them as soon as we have
the info available.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA988X firmware starting from 10.2.4.70.12-2 has capability to support
Mesh Control Field Present bit in QoS field in native Wi-Fi mode.
Hence apply Mesh subtype according to the WMI service map.
Firmware will allows unicast, broadcast, multicast, and WDS frame
(FromDS = 1 and ToDS = 1) to be received via the interface, once Mesh
subtype is used.
The firmware and this patch together make native Wi-Fi mode comply to
IEEE802.11s Mesh frame in open mode, but the firmware doesn't yet
support secured Mesh mode.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA988X firmware starting from 10.2.4.70.12-2 supports new
vdev subtypes for proxy STA and Mesh, hence add them to be used
as needed.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update WMI 10.x service map to sync with firmware 10.2.4.70.12-2
released on 11/11/2015 which is the latest QCA988X firmware as of
11/18/2015.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix write permission for few of the debugfs entries
which support write file operations as well.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allocations from the DMA zone were originally added for legacy ISA
stuff, or PCI devices that have specific limitations in their DMA
addressing capabilities. It has no place in ath10k, which can do
full 32-bit DMA.
Fixes memory allocation errors on some platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable AP + STA interface combination support for 10.x and
this enables Repeater mode testing (with WDS Repeater combinations
as well). Fix indentation as well.
Based on the suggestions from Michal and Yanbo Li,
thanks to them
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The error message order of board data fetch is board info,
directory, and then file name, hence place print arguments
in the order.
Fixes: 0a51b343ab ("ath10k: add board 2 API support")
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On wcn3620, firmware response to remove_bsskey uses the new, larger
"v2" format
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On wcn3620, firmware response to trigger_ba uses the new, larger
"v2" format
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn3620 has a new message structure for the reply to some hal
commands. This patch adds the struct and helper routine that
uses it if the chip is wcn3620, or falls back to the old
helper routine.
We don't know what to do with the candidate list he sends back,
but we can at least accept and ignore it nicely instead of dying.
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3620 can asynchronously send two new kinds of indication message,
since we can't handle them just accept them quietly.
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3620 firmware introduces a new async indication, we need to
add it as a known message type so we can accept it
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless and change the menuconfig to follow the same
categorisation. This unifies the directory layout as we already had few drivers
already using vendor directories (especially ath and ti).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWVXM4AAoJEG4XJFUm622b4lYH/2/zdRtLhAYS7QoVXD11Vbdh
ydkMAAb0yuu6z2bakgGMRT8oAyFyU7WXzsAR1YoCRQEC19Sk8jrvtEufl3irsUA6
CtRPgr8GwDO6qAneEkBv9QC8wMcEifpdXl5XdTOSGYhm2IslsB9Fw5/vv8MLQzLJ
V22OB3ZVyUxtpbkS1ZkiAu0KYZu0104Agyk3yes1nhZWSP8Wtfg2CNKhvy9Y6zDt
HPk8ANMkP0HL1OngocUmtuc7CJn/aZsgPFo94NgmeF2gtG0HbtXYD/MqAOFPWwMg
807gM3knq4jiNCXGy5itrwtKx0BrObQD05IbzOezHuO6nsFUAbRNVsmxEj6Bj7Q=
=BM98
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Add vendor directories (for example intel, marvell and so on) to
drivers/net/wireless and change the menuconfig to follow the same
categorisation. This unifies the directory layout as we already had few drivers
already using vendor directories (especially ath and ti).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We check for overflow here, but we don't check for underflow so it
causes a static checker warning.
Fixes: fb9987d0f7 ('ath9k_htc: Support for AR9271 chipset.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
