There are some minor differences when assigning VF resources on the
new chips. The MSIX (NQ) resource has to be assigned and ring group
is not needed on the new chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bringing up a device, the code checks to see if the number of
MSIX has changed. pci_disable_msix() should be called first before
changing the number of reserved NQs/CMPL rings. This ensures that
the MSIX vectors associated with the NQs/CMPL rings are still
properly mapped when pci_disable_msix() masks the vectors.
This patch will prevent errors when RDMA support is added for the new
57500 chips. When the RDMA driver shuts down, the number of NQs is
decreased and we must use the new sequence to prevent MSIX errors.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en requires same number of stat_ctxs as CP rings but RDMA
requires only 1 stat_ctx. Also add a new parameter resv_stat_ctxs
to better keep track of stat_ctxs reserved including resources used
by RDMA. Add a stat_ctxs parameter to all the relevant resource
reservation functions so we can reserve the correct number of
stat_ctxs.
Prior to this patch, we were not reserving the extra stat_ctx for
RDMA and RDMA would not work on the new 57500 chips.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling bnxt_set_max_func_stat_ctxs() to modify max stat_ctxs requested
or freed by the RDMA driver is wrong. After introducing reservation of
resources recently, the driver has to keep track of all stat_ctxs
including the ones used by the RDMA driver. This will provide a better
foundation for accurate accounting of the stat_ctxs.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For bnxt_en driver, stat_ctxs created will always be same as
cp_nr_rings. Remove extra variable that duplicates the value.
Also introduce bnxt_get_avail_stat_ctxs_for_en() helper to get
available stat_ctxs and bnxt_get_ulp_stat_ctxs() helper to return
number of stat_ctxs used by RDMA.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The available CP rings are calculated differently on the new 57500
chips, so add this helper to do this calculation correctly. The
VFs will be assigned these available CP rings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF has a pool of NQs and MSIX vectors assigned to it based on
NVRAM configurations. The number of usable MSIX vectors on the PF
is the minimum of the NQs and MSIX vectors. Any excess NQs without
associated MSIX may be used for the VFs, so we need to store this
max_nqs value. max_nqs minus the NQs used by the PF will be the
available NQs for the VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handling exceptions for direct UDP encapsulation in GUE (that is,
UDP-in-UDP) leads to unbounded recursion in the GUE exception handler,
syzbot reported.
While draft-ietf-intarea-gue-06 doesn't explicitly forbid direct
encapsulation of UDP in GUE, it probably doesn't make sense to set up GUE
this way, and it's currently not even possible to configure this.
Skip exception handling if the GUE proto/ctype field is set to the UDP
protocol number. Should we need to handle exceptions for UDP-in-GUE one
day, we might need to either explicitly set a bound for recursion, or
implement a special iterative handling for these cases.
Reported-and-tested-by: syzbot+43f6755d1c2e62743468@syzkaller.appspotmail.com
Fixes: b8a51b38e4 ("fou, fou6: ICMP error handlers for FoU and GUE")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to control carrier from /sys/class/net/ethX/carrier
for Fixed PHYs.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to control carrier from /sys/class/net/ethX/carrier
for Fixed PHYs.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to control carrier from /sys/class/net/ethX/carrier
for Fixed PHYs.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers can use this as .ndo_change_carrier() to change carrier
via /sys/class/net/ethX/carrier.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kzalloc_node(..., GFP_KERNEL, node) will attempt to allocate
memory as close as possible to the node.
There is no need to fallback to kzalloc() if this has failed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the ethtool entries to control the port should be supported by
the uplink rep netdev in switchdev mode, add them.
While here, add also the get/set coalesce entries for all reps.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Towards supporting set/get of global pause for the port
and get of the port link ksetting from the uplink representor,
expose the relevant entries to other mlx5 callers.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Some of the sriov ndo calls are needed also on the switchdev mode -
e.g setup VF mac and reading vport stats. Add them to the uplink rep
netdev ops. Same for the UDP tunnel ones, need them there to identify
offloaded udp tunnel ports.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Take care of setup/teardown for the port link, dcb, lag as well as
dealing with port mtu and carrier for e-switch uplink representors.
This is achieved by adding a dedicated profile instance for uplink
representors which includes the enable/disable and more profile routines
which are invoked by the general mlx5e code for netdev attach/detach.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Now, when we have a dedicated uplink representor, the netdev instance
set over the esw manager vport (PF) is of no-use. As such, remove it
once we're on switchdev mode and get it back to life when off switchdev.
This is done by reloading the Ethernet interface as well (we already
do that for the IB interface) from the eswitch code while going in/out
of switchdev mode.
The Eth add/remove entries are modified to act differently when called in
switchdev mode. In this case we only deal with registration of the eth
vport representors. The rep netdevices are created from the eswitch call
to load the registered eth representors.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove some last leftovers from using the PF netdev as
the e-switch uplink representor.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, when running in sriov switchdev mode, we are using the PF
netdevice as the uplink representor, this is problematic from few aspects:
- will break when the PF isn't eswitch manager (e.g smart NIC env)
- misalignment with other NIC switchdev drivers
- makes us have and maintain special code, hurts the driver quality/robustness
- which in turn opens the door for future bugs
As of each and all of the above, we move to have a dedicated netdev representor
for the uplink vport in a similar manner done for for the VF vports.
This includes the following:
1. have an uplink rep netdev as we have for VF reps
2. all reps use same load/unload functions
3. HW stats for uplink based on physical port counters and not vport counters
4. link state for the uplink managed through PAOS and not vport state
5. the uplink rep has sysfs link to the PF PCI function && uses the PF MAC address
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This is prep step towards adding dedicated uplink representor.
The patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The reload of the IB interface done on the offloads stop call is
redundant b/c we do that on mlx5_eswitch_disable_sriov(), remove it.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The kbuild bot reported a build breakage with CONFIG_RETPOLINE=n
due to commit aaa5d90b39 ("net: use indirect call wrappers at
GRO network layer").
I screwed the wrapper implementation for such config.
Fix the issue properly ignoring the builtin symbols arguments,
when retpoline is not enabled.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: aaa5d90b39 ("net: use indirect call wrappers at GRO network layer")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: spectrum_acl: Add Bloom filter support
Nir says:
Spectrum-2 uses Bloom filter to reduce the number of lookups in the
algorithmic TCAM (A-TCAM). HW performs multiple exact match lookups in a
given region using a key composed of { packet & mask, mask ID, region ID }.
The masks which are used in a region are called rule patterns or RP.
When such multiple masks are used, the A-TCAM region uses an eRP
(extended RP) table that describes which rule patterns are in use and
defines the order of the lookup. When eRP table is used in a region, one
way to reduce the number of the lookups is to consult a Bloom filter
before doing the lookup.
A Bloom filter is a space-efficient probabilistic data structure, on
which a query returns either "possibly in set" or "definitely not in
set". HW can skip a lookup if a query on the Bloom filter results a
"definitely not set" response. The mlxsw driver implements a "counting
filter" and when either a new entry is marked or the last entry is
removed it will update the HW. Update of this counting filter occurs
when rule is configured or deleted from a region.
Patch #1 adds PEABFE register which is used for setting Bloom filter
entries.
Patch #2 adds Bloom filter resources.
Patch #3 and patch #4 provide Bloom filter handling within mlxsw, by
adding initialization and logic for updating the Bloom bit vector in HW.
Patch #5 and patch #6 add required calls for Bloom filter update as part
of rule configuration flow.
Patch #7 handles transitions to and from eRP table. It uses a list to
keep A-TCAM rules in order to update rules in Bloom filter, in cases of
transitions from master mask based A-TCAM region to an eRP table based
region and vice versa.
Patch #8 removes a trick done on master RP index to a remaining RP,
since Bloom filter is updated on eRP transitions.
Finally, patch #9 activates Bloom filter mechanism in HW, by cancelling
the bypass that was configured before and the remaining three patches
are selftests that exercise the new code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The eRP table is active when there is more than a single rule
pattern. It may be that the patterns are close enough and use delta
mechanism. Bloom filter index computation is based on the values of
{rule & mask, mask ID, region ID} where the rule delta bits must be
cleared.
Add a test that exercises Bloom filter with delta mechanism.
Configure rules within delta range and pass a packet which is
supposed to hit the correct rule.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bloom filter index computation is based on the values of
{rule & mask, mask ID, region ID} and the computation also varies
according to the region key size.
Add a test that exercises the possible combinations by creating
multiple chains using different key sizes and then pass a frame that
is supposed to to produce a hit on all of the regions.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that exercises Bloom filter code.
Activate eRP table in the region by adding multiple rule patterns which
with very high probability use different entries in the Bloom filter.
Then send packets in order to check lookup hits on all relevant rules.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mlxsw driver handles all aspects of updating
the Bloom filter mechanism, set bf_bypass value to false
and allow HW to use Bloom filter.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bloom filter is updated on transitions from a single rule pattern,
also called master RP, to eRP table and vice versa. Since rules are
being written to or deleted from the Bloom filter on such transitions,
it is not required to keep the same eRP bank ID for the master RP.
Change master RP index assignment so it will be assigned with zero.
This is consistent with the assignment of the first available spot
that is used for allocating eRP's indices.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bloom filter update is required only for rules which reside on an
eRP. When the region has only a single rule pattern then eRP table
is not used, however insertion of another pattern would trigger a
move to an active eRP table so it is imperative to update the Bloom
filter with all previously configured rules.
Add a method that updates Bloom filter entries for all rules
currently configured in the region, on the event of a transition
from master mask to eRP, or vice versa. For that purpose, maintain
a list of all A-TCAM rules within mlxsw_sp_acl_atcam_region.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add calls to eRP module for updating Bloom filter when a rule is
added or removed from the A-TCAM. eRP module will update the Bloom
filter only for cases in which the region has an active eRP table.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Bloom filter update for rule insertion and rule removal scenarios.
This is done within eRP module in order to assure that Bloom filter
updates are done only for rules which are part of an eRP, as HW does not
consult Bloom filter for entries when there is a single (master) mask in
the region.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 HW uses Bloom filter in order to skip lookups on specific
eRPs. It uses crc-16-Msbit-first calculation over a specific layout
of a rule's key fields combined with eRP ID as well as region ID.
Per potential lookup, iff the Bloom filter entry of the calculated
index is empty, then the lookup can be skipped. Hence, the mlxsw
driver should update the Bloom filter entry per each rule insertion
or deletion when rules are part of an eRP.
Add functions for adding and deleting entries in the Bloom filter.
In order to do so also add crc-16 computation based on the specific
Spectrum-2 polynomial and a function for encoding the crc-16 input
in the manner dictated by HW implementation.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lay the foundations for Bloom filter handling. Introduce a new file for
Bloom filter actions.
Add struct mlxsw_sp_acl_bf to struct mlxsw_sp_acl_erp_core and initialize
the Bloom filter data structure. Also take care of proper destruction when
terminating.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the maximum Bloom filter logarithmic size per eRP table bank.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bloom filter is a bit vector which allows the HW a fast lookup on a
small size bit vector, that may reduce the number of lookups on the
A-TCAM memory. PEABFE register allows setting values to the bits of
the bit vector mentioned above.
Add the register to be later used in A-TCAM optimizations.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu says:
====================
rtnl fdb get
This series adds support for rtnl fdb get similar to
route get.
v2: add nda_policy, fixes to exact msgs, strict nlmsg parsing
v3: remove unnecessary attribute length checks + simplify code
as pointed out by david
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
tests the below three cases of bridge fdb get:
[bridge, mac, vlan]
[bridge_port, mac, vlan, flags=[NTF_MASTER]]
[vxlandev, mac, flags=NTF_SELF]
depends on iproute2 support for bridge fdb get.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements ndo_fdb_get for a vxlan device.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements ndo_fdb_get for the bridge
fdb.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for fdb get similar to
route get. arguments can be any of the following (similar to fdb add/del/dump):
[bridge, mac, vlan] or
[bridge_port, mac, vlan, flags=[NTF_MASTER]] or
[dev, mac, [vni|vlan], flags=[NTF_SELF]]
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut says:
====================
net: dsa: ksz: Clean up the tag code in prep for more switches
Clean up the KSZ DSA tag code in preparation for adding more switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the destination address is link local, add override bit into the
switch tag to let such a packet through the switch even if the port is
blocked.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out common code from the tag_ksz , so that the code can be used
with other KSZ family switches which use differenly sized tags.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW team asks to be able to not support RED even if NIC is capable
of buffering for testing and experimentation. Add an opt-out flag.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ec49d83f24.
Cause build failures when DCCP is modular.
ERROR: "inet_hashinfo2_init" [net/dccp/dccp.ko] undefined!
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to routes and rules, add protocol attribute to neighbor entries
for easier tracking of how each was created.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds coverage of DCCP to reuseport_addr_any selftest.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d9fbc7f643 "net: tcp: prefer listeners bound to an address"
removes port-only listener lookups. This caused segfaults in DCCP
lookups because DCCP did not initialize the (addr,port) hashtable.
This patch adds said initialization.
The only non-trivial issue here is the size of the new hashtable.
It seemed reasonable to make it match the size of the port-only
hashtable (= INET_LHTABLE_SIZE) that was used previously. Other
parameters to inet_hashinfo2_init() match those used in TCP.
Tested: syzcaller issues fixed; the second patch in the patchset
tests that DCCP lookups work correctly.
Fixes: d9fbc7f643 "net: tcp: prefer listeners bound to an address"
Reported-by: syzcaller <syzkaller@googlegroups.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
