Remove unnecessary #address-cells/#size-cells from the switch nodes
to fix the following DTC warnings:
arch/arm/boot/dts/imx6q-b450v3.dtb: Warning (avoid_unnecessary_addr_size): /mdio-gpio/switch@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch 2 has an 88e1545 PHY behind it, which is a quad PHY. Only the
first three PHYs are used, the remaining PHY is unused. When we wire
up the SFF sockets in a later commit, the omission of this causes the
fourth PHY to be used for port 3. Specifying the PHYs in DT avoids
the auto-probing of the bus, and discovery of this PHY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The interrupt specification for the GPIO expander is wrong - the
expander is wired to PTB28, which is GPIO98. GPIO98 is on gpio chip
3, not 2.
In addition, the device is missing a required property. Interrupt
controllers must have the "interrupt-controller" property specified.
Add this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Two of the Ethernet switches on this board have EEPROMs connected.
Add the eeprom-length property to the device tree, making it possible
to access the EEPROM using ethtool -e.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename the switch2@0 label of the switch2 node to switch@0 to respect
the general unit@address DTS rule, and be consistent with the other
switch nodes of the DTS file.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The devel B and devel C board use the same GPIO lines for interrupts
from the two switches. Move the pinmux nodes from devel B into the
shared .dtsi file, and wire up the interrupts on devel C.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- New board support: vf610-zii-dev-rev-c, imx6ul-opos6uldev,
imx6ul-isiot, imx6qdl-savageboard, imx6q-mccmon6.
- A patch from Alexandre to correct the mangled license text which
has been copied & pasted all over the i.MX device tree files.
- Update cpu nodes of some i.MX SoCs to make them consistent and match
ePAPR spec.
- Add OCOTP device for i.MX6UL SoC.
- Add security violation interrupt for i.MX25 DryIce.
- Enable USB OTG, WIFI and Bluetooth support for i.MX6SX Udoo Neo
board.
- Enable S/PDIF and 2nd display pipeline support for CompuLab board..
- Add SPI and LTC3676 PMIC support for Gateworks Ventana boards.
- A few random device addition for various boards: TVE DAC regulators
for imx53-qsb, EEPROM for vf610-zii-dev, eMMC and NAND support for
i.MX6UL Engicam boards.
- Cleanups on obsoleted or unused properties.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYjWLQAAoJEFBXWFqHsHzOGt0H/2WCsuRi6WU7i7Wyk/S0Xq5t
HzA/9m2f7z1vb1tzFknbpcWYa9bdofI7Dz+6KW2vp4fxhMyJn8SQxWwQjVNya2ba
z8XLdEMlIuozBebPcH84ovNzqoBIOEFahGm5smm40s/o7XL8ua9tOEFaUc+jY0Pd
n/3TPmoyBTlbrgiCZfLXCVsczHtEVW5JoQmXT7aDsxT0BQpnwLbgXKVOxgDvsWXM
WtAKjpGvdiApD3znbFjYmRKak+2uilkV5B4jrL4mZf8dxCliykP4XA/LbiMLKAMN
voMpTtTK7UYp59GrwKbqfJ+pPU7b6ndKK59f7FWrTDNgtDGe+J4ExjWwsDnuLfI=
=HAbg
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree updates for 4.11:
- New board support: vf610-zii-dev-rev-c, imx6ul-opos6uldev,
imx6ul-isiot, imx6qdl-savageboard, imx6q-mccmon6.
- A patch from Alexandre to correct the mangled license text which
has been copied & pasted all over the i.MX device tree files.
- Update cpu nodes of some i.MX SoCs to make them consistent and match
ePAPR spec.
- Add OCOTP device for i.MX6UL SoC.
- Add security violation interrupt for i.MX25 DryIce.
- Enable USB OTG, WIFI and Bluetooth support for i.MX6SX Udoo Neo
board.
- Enable S/PDIF and 2nd display pipeline support for CompuLab board..
- Add SPI and LTC3676 PMIC support for Gateworks Ventana boards.
- A few random device addition for various boards: TVE DAC regulators
for imx53-qsb, EEPROM for vf610-zii-dev, eMMC and NAND support for
i.MX6UL Engicam boards.
- Cleanups on obsoleted or unused properties.
* tag 'imx-dt-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (32 commits)
ARM: dts: udoo_neo: Add Bluetooth support
ARM: dts: udoo_neo: Add Wifi support
ARM: dts: udoo_neo: Add UDOO Neo USB OTG1 and OTG2 support
ARM: dts: imx6ul: Add Engicam Is.IoT MX6UL NAND initial support
ARM: dts: imx6ul: Add Engicam Is.IoT MX6UL eMMC initial support
ARM: dts: imx6qdl: Fix "ERROR: code indent should use tabs where possible"
ARM: dts: vf610-zii-dev: add EEPROM entry to Rev C
ARM: dts: add Armadeus Systems OPOS6UL and OPOS6ULDEV support
ARM: dts: imx6q-utilite-pro: enable 2nd display pipeline
ARM: dts: vf610-zii-dev: Add .dts file for rev. C
ARM: dts: vf610-zii-dev-rev-b: Remove leftover PWM pingroup
ARM: dts: imx6: Support Savageboard quad
ARM: dts: imx6: Support Savageboard dual
ARM: dts: imx6: Add Savageboard common file
ARM: dts: imx53-qsb: Provide the TVE DAC regulators
ARM: dts: imx6q: Add mccmon6 board support
Doc: devicetree: bindings: Add vendor prefix entry - lwn
ARM: dts: imx/vf: Correct license text
ARM: dts: imx25.dtsi: DryIce security violation interrupt
ARM: dts: imx: Add ocotp node for imx6ul
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add .dts file for rev. C of the board by factoring out commonalities
into a shared include file (vf610-zii-dev-rev-b-c.dtsi) and deriving
revision specific file from it (vf610-zii-dev-rev-b.dts and
vf610-zii-dev-reb-c.dts).
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: andrew@lunn.ch
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: cphealy@gmail.com
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove pwm0grp since it is:
a) Not referenced anywhere in the DTS file (unlike Tower board it
is based on, this board does not use/expose FTM0)
b) Configures PTB2 and PTB3 in a way that contradicts
pinctrl-mdio-mux
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: andrew@lunn.ch
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: cphealy@gmail.com
Tested-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The license text has been mangled at some point then copy pasted across
multiple files. Restore it to what it should be.
Note that this is not intended as a license change.
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Found while reviewing Marvell dsa bindings usage.
Fixes: f283745b3c ("arm: vf610: zii devel b: Add support for switch interrupts")
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where things
come together.
We get a DT descriptions for a couple of new SoCs, all of them variants
of other chips we already support, and usually coming with a new
evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers
or industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on
Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it into
products and have served their purpose in the kernel as a template
for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree
Conflicts:
arch/arm/boot/dts/r8a*.dtsi: a node was added
the clk tree, keep both sides and watch out for git
dropping the required '};' at the end of each side.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wJt3
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
I2C3 bus was only brought out in revision A1 of the board and revision
B1 only brings out 3 I2C busses (I2C0, I2C1 and I2C2).
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Switches use GPIO lines to indicate interrupts from two of the
switches.
With these interrupts in place, we can make use of the interrupt
controllers within the switch to indicate when the internal PHYs
generate an interrupt. Use standard PHY properties to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hang the three switches of the three MDIO busses using the new DSA
binding. Also, make use of the mdio-bus and explicitly list the phys
on one device. This is not required, but good for testing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds support for Rev. B of a Zodiac Inflight Innovations
development board, mainly intended for DSA and ARINC 429 development
work.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
