Commit Graph

21937 Commits

Author SHA1 Message Date
Oliver Neukum
9cdabcb3ef usblp: fix race between disconnect() and read()
read() needs to check whether the device has been
disconnected before it tries to talk to the device.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+be5b5f86a162a6c281e6@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20200917103427.15740-1-oneukum@suse.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-17 18:45:30 +02:00
Quentin Perret
29231826f3 ehci-hcd: Move include to keep CRC stable
The CRC calculation done by genksyms is triggered when the parser hits
EXPORT_SYMBOL*() macros. At this point, genksyms recursively expands the
types of the function parameters, and uses that as the input for the CRC
calculation. In the case of forward-declared structs, the type expands
to 'UNKNOWN'. Following this, it appears that the result of the
expansion of each type is cached somewhere, and seems to be re-used
when/if the same type is seen again for another exported symbol in the
same C file.

Unfortunately, this can cause CRC 'stability' issues when a struct
definition becomes visible in the middle of a C file. For example, let's
assume code with the following pattern:

    struct foo;

    int bar(struct foo *arg)
    {
	/* Do work ... */
    }
    EXPORT_SYMBOL_GPL(bar);

    /* This contains struct foo's definition */
    #include "foo.h"

    int baz(struct foo *arg)
    {
	/* Do more work ... */
    }
    EXPORT_SYMBOL_GPL(baz);

Here, baz's CRC will be computed using the expansion of struct foo that
was cached after bar's CRC calculation ('UNKOWN' here). But if
EXPORT_SYMBOL_GPL(bar) is removed from the file (because of e.g. symbol
trimming using CONFIG_TRIM_UNUSED_KSYMS), struct foo will be expanded
late, during baz's CRC calculation, which now has visibility over the
full struct definition, hence resulting in a different CRC for baz.

The proper fix for this certainly is in genksyms, but that will take me
some time to get right. In the meantime, we have seen one occurrence of
this in the ehci-hcd code which hits this problem because of the way it
includes C files halfway through the code together with an unlucky mix
of symbol trimming.

In order to workaround this, move the include done in ehci-hub.c early
in ehci-hcd.c, hence making sure the struct definitions are visible to
the entire file. This improves CRC stability of the ehci-hcd exports
even when symbol trimming is enabled.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20200916171825.3228122-1-qperret@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-17 08:39:50 +02:00
Madhusudanarao Amara
d69030c91b usb: typec: intel_pmc_mux: Handle SCU IPC error conditions
Check and return if there are errors. The response bits are valid
only on no errors.

Fixes: b7404a29cd ("usb: typec: intel_pmc_mux: Definitions for response status bits")
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916091102.27118-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16 13:09:31 +02:00
Penghao
bcea6dafee USB: quirks: Add USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for BYD zhaoxin notebook
Add a USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for the BYD zhaoxin notebook.
This notebook come with usb touchpad. And we would like to disable
touchpad wakeup on this notebook by default.

Signed-off-by: Penghao <penghao@uniontech.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200907023026.28189-1-penghao@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16 13:08:18 +02:00
Oliver Neukum
325b008723 USB: UAS: fix disconnect by unplugging a hub
The SCSI layer can go into an ugly loop if you ignore that a device is
gone. You need to report an error in the command rather than in the
return value of the queue method.

We need to specifically check for ENODEV. The issue goes back to the
introduction of the driver.

Fixes: 115bb1ffa5 ("USB: Add UAS driver")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200916094026.30085-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16 12:35:14 +02:00
Heikki Krogerus
386e15a650 usb: typec: ucsi: Prevent mode overrun
Sometimes the embedded controller firmware does not
terminate the list of alternate modes that the partner
supports in its response to the GET_ALTERNATE_MODES command.
Instead the firmware returns the supported alternate modes
over and over again until the driver stops requesting them.

If that happens, the number of modes for each alternate mode
will exceed the maximum 6 that is defined in the USB Power
Delivery specification. Making sure that can't happen by
adding a check for it.

This fixes NULL pointer dereference that is caused by the
overrun.

Fixes: ad74b8649b ("usb: typec: ucsi: Preliminary support for alternate modes")
Cc: stable@vger.kernel.org
Reported-by: Zwane Mwaikambo <zwanem@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916090034.25119-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16 12:34:10 +02:00
Heikki Krogerus
130a96d698 usb: typec: ucsi: acpi: Increase command completion timeout value
UCSI specification quite clearly states that if a command
can't be completed in 10ms, the firmware must notify
about BUSY condition. Unfortunately almost none of the
platforms (the firmware on them) generate the BUSY
notification even if a command can't be completed in time.

The driver already considered that, and used a timeout
value of 5 seconds, but processing especially the alternate
mode discovery commands takes often considerable amount of
time from the firmware, much more than the 5 seconds. That
happens especially after bootup when devices are already
connected to the USB Type-C connector. For now on those
platforms the alternate mode discovery has simply failed
because of the timeout.

To improve the situation, increasing the timeout value for
the command completion to 1 minute. That should give enough
time for even the slowest firmware to process the commands.

Fixes: f56de278e8 ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916090034.25119-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16 12:34:03 +02:00
Greg Kroah-Hartman
a29c0adbb6 USB-serial fixes for 5.9-rc5
Here are some new device ids for 5.9.
 
 All have been in linux-next with no reported issues.
 -----BEGIN PGP SIGNATURE-----
 
 iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCX1embwAKCRALxc3C7H1l
 CLYoAQDVrO56s8bOd5JW3NpuDCDUgDSt3dBrXNF+PhHKX0TDAAEAztQesI4MgXLz
 p0X1nJvdlwQgRTTJzI84HaUTRZk+EQc=
 =1W7v
 -----END PGP SIGNATURE-----

Merge tag 'usb-serial-5.9-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for 5.9-rc5

Here are some new device ids for 5.9.

All have been in linux-next with no reported issues.

* tag 'usb-serial-5.9-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: option: support dynamic Quectel USB compositions
  USB: serial: option: add support for SIM7070/SIM7080/SIM7090 modules
  USB: serial: ftdi_sio: add IDs for Xsens Mti USB converter
2020-09-08 17:50:58 +02:00
Utkarsh Patel
7c6bbdf086 usb: typec: intel_pmc_mux: Do not configure SBU and HSL Orientation in Alternate modes
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.7, bits 4 and 5 are reserved in Alternate modes.
SBU Orientation and HSL Orientation needs to be configured only during
initial cable detection in USB connect flow based on device property of
"sbu-orientation" and "hsl-orientation".
Configuring these reserved bits in the Alternate modes may result in delay
in display link training or some unexpected behaviour.
So do not configure them while issuing Alternate Mode requests.

Fixes: ff4a30d5e2 ("usb: typec: mux: intel_pmc_mux: Support for static SBU/HSL orientation")
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200907142152.35678-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-07 17:05:02 +02:00
Utkarsh Patel
294955fd43 usb: typec: intel_pmc_mux: Do not configure Altmode HPD High
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.7, bit 14 is reserved in Alternate mode.
In DP Alternate Mode state, if the HPD_STATE (bit 7) field in the
status update command VDO is set to HPD_HIGH, HPD is configured via
separate HPD mode request after configuring DP Alternate mode request.
Configuring reserved bit may show unexpected behaviour.
So do not configure them while issuing the Alternate Mode request.

Fixes: 7990be48ef ("usb: typec: mux: intel: Handle alt mode HPD_HIGH")
Cc: stable@vger.kernel.org
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200907142152.35678-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-07 17:04:59 +02:00
Zeng Tao
a18cd6c9b6 usb: core: fix slab-out-of-bounds Read in read_descriptors
The USB device descriptor may get changed between two consecutive
enumerations on the same device for some reason, such as DFU or
malicius device.
In that case, we may access the changing descriptor if we don't take
the device lock here.

The issue is reported:
https://syzkaller.appspot.com/bug?id=901a0d9e6519ef8dc7acab25344bd287dd3c7be9

Cc: stable <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+256e56ddde8b8957eabd@syzkaller.appspotmail.com
Fixes: 217a9081d8 ("USB: add all configs to the "descriptors" attribute")
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Link: https://lore.kernel.org/r/1599201467-11000-1-git-send-email-prime.zeng@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04 16:41:22 +02:00
Amjad Ouled-Ameur
a6498d5182 Revert "usb: dwc3: meson-g12a: fix shared reset control use"
This reverts commit 7a410953d1.

This commit breaks USB on meson-gxl-s905x-libretech-cc. Reverting
the change solves the issue.

In fact, according to the reset framework code, consumers must not use
reset_control_(de)assert() on shared reset lines when reset_control_reset
has been used, and vice-versa.

Moreover, with this commit, usb is not guaranted to be reset since the
reset is likely to be initially deasserted.

Reverting the commit will bring back the suspend warning mentioned in the
commit description. Nevertheless, a warning is much less critical than
breaking dwc3-meson-g12a USB completely. We will address the warning
issue in another way as a 2nd step.

Fixes: 7a410953d1 ("usb: dwc3: meson-g12a: fix shared reset control use")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20200827144810.26657-1-aouledameur@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04 16:41:22 +02:00
Heikki Krogerus
1f3546ff3f usb: typec: ucsi: acpi: Check the _DEP dependencies
Failing probe with -EPROBE_DEFER until all dependencies
listed in the _DEP (Operation Region Dependencies) object
have been met.

This will fix an issue where on some platforms UCSI ACPI
driver fails to probe because the address space handler for
the operation region that the UCSI ACPI interface uses has
not been loaded yet.

Fixes: 8243edf441 ("usb: typec: ucsi: Add ACPI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200904110918.51546-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04 16:41:22 +02:00
Madhusudanarao Amara
290a405ce3 usb: typec: intel_pmc_mux: Un-register the USB role switch
Added missing code for un-register USB role switch in the remove and
error path.

Cc: Stable <stable@vger.kernel.org> # v5.8
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Fixes: 6701adfa96 ("usb: typec: driver for Intel PMC mux control")
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Link: https://lore.kernel.org/r/20200825183811.7262-1-madhusudanarao.amara@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04 16:41:22 +02:00
Mathias Nyman
cfd54fa83a usb: Fix out of sync data toggle if a configured device is reconfigured
Userspace drivers that use a SetConfiguration() request to "lightweight"
reset an already configured usb device might cause data toggles to get out
of sync between the device and host, and the device becomes unusable.

The xHCI host requires endpoints to be dropped and added back to reset the
toggle. If USB core notices the new configuration is the same as the
current active configuration it will avoid these extra steps by calling
usb_reset_configuration() instead of usb_set_configuration().

A SetConfiguration() request will reset the device side data toggles.
Make sure usb_reset_configuration() function also drops and adds back the
endpoints to ensure data toggles are in sync.

To avoid code duplication split the current usb_disable_device() function
and reuse the endpoint specific part.

Cc: stable <stable@vger.kernel.org>
Tested-by: Martin Thierer <mthierer@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200901082528.12557-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04 16:41:22 +02:00
Bjørn Mork
2bb70f0a4b USB: serial: option: support dynamic Quectel USB compositions
The USB composition, defining the set of exported functions, is dynamic
in newer Quectel modems.  Default functions can be disabled and
alternative functions can be enabled instead.  The alternatives
includes class functions using interface pairs, which should be
handled by the respective class drivers.

Active interfaces are numbered consecutively, so static
blacklisting based on interface numbers will fail when the
composition changes.  An example of such an error, where the
option driver has bound to the CDC ECM data interface,
preventing cdc_ether from handling this function:

 T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
 P: Vendor=2c7c ProdID=0125 Rev= 3.18
 S: Manufacturer=Quectel
 S: Product=EC25-AF
 C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
 A: FirstIf#= 4 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
 I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
 E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
 E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
 E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
 E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
 E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
 E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
 E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 I:* If#= 4 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=(none)
 E: Ad=89(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
 I:* If#= 5 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=option
 I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=option
 E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Another device with the same id gets correct drivers, since the
interface of the network function happens to be blacklisted by option:

 T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
 P: Vendor=2c7c ProdID=0125 Rev= 3.18
 S: Manufacturer=Android
 S: Product=Android
 C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
 I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
 E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
 E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
 E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
 E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
 E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
 E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
 E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
 E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
 E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Change rules for EC21, EC25, BG96 and EG95 to match vendor specific
serial functions only, to prevent binding to class functions. Require
2 endpoints on ff/ff/ff functions, avoiding the 3 endpoint QMI/RMNET
network functions.

Cc: AceLan Kao <acelan.kao@canonical.com>
Cc: Sebastian Sjoholm <ssjoholm@mac.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
2020-08-31 08:37:17 +02:00
Aleksander Morgado
1ac6987908 USB: serial: option: add support for SIM7070/SIM7080/SIM7090 modules
These modules have 2 different USB layouts:

The default layout with PID 0x9205 (AT+CUSBSELNV=1) exposes 4 TTYs and
an ECM interface:

  T:  Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  6 Spd=480 MxCh= 0
  D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
  P:  Vendor=1e0e ProdID=9205 Rev=00.00
  S:  Manufacturer=SimTech, Incorporated
  S:  Product=SimTech SIM7080
  S:  SerialNumber=1234567890ABCDEF
  C:  #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA
  I:  If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
  I:  If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
  I:  If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
  I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
  I:  If#=0x4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
  I:  If#=0x5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether

The purpose of each TTY is as follows:
 * ttyUSB0: DIAG/QCDM port.
 * ttyUSB1: GNSS data.
 * ttyUSB2: AT-capable port (control).
 * ttyUSB3: AT-capable port (data).

In the secondary layout with PID=0x9206 (AT+CUSBSELNV=86) the module
exposes 6 TTY ports:

  T:  Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  8 Spd=480 MxCh= 0
  D:  Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
  P:  Vendor=1e0e ProdID=9206 Rev=00.00
  S:  Manufacturer=SimTech, Incorporated
  S:  Product=SimTech SIM7080
  S:  SerialNumber=1234567890ABCDEF
  C:  #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA
  I:  If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
  I:  If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
  I:  If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
  I:  If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
  I:  If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
  I:  If#=0x5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

The purpose of each TTY is as follows:
 * ttyUSB0: DIAG/QCDM port.
 * ttyUSB1: GNSS data.
 * ttyUSB2: AT-capable port (control).
 * ttyUSB3: QFLOG interface.
 * ttyUSB4: DAM interface.
 * ttyUSB5: AT-capable port (data).

Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
2020-08-31 08:33:41 +02:00
Linus Torvalds
6f0306d1bf USB fixes for 5.9-rc3 - take 2
Let's try this again...  Here are some USB fixes for 5.9-rc3.
 
 This differs from the previous pull request for this release in that:
 	- the usb gadget patch now does not break some systems, and
 	  actually does what it was intended to do.  Many thanks to
 	  Marek Szyprowski for quickly noticing and testing the patch
 	  from Andy Shevchenko to resolve this issue.
 	- some more new USB quirks have been added to get some new
 	  devices to work properly based on user reports.
 
 Other than that, the original pull request patches are all here, and
 they contain:
 	- usb gadget driver fixes
 	- xhci driver fixes
 	- typec fixes
 	- new quirks and ids
 	- fixes for USB patches that went into 5.9-rc1.
 
 All of these have been tested in linux-next with no reported issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX0t32g8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ylFMACeLEQgeN1rmfQfLyo2NHROQEeDhnIAniLMhchZ
 p9dXWJ8aNeyI5OrNjD5b
 =Vd05
 -----END PGP SIGNATURE-----

Merge tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
 "Let's try this again...  Here are some USB fixes for 5.9-rc3.

  This differs from the previous pull request for this release in that
  the usb gadget patch now does not break some systems, and actually
  does what it was intended to do. Many thanks to Marek Szyprowski for
  quickly noticing and testing the patch from Andy Shevchenko to resolve
  this issue.

  Additionally, some more new USB quirks have been added to get some new
  devices to work properly based on user reports.

  Other than that, the patches are all here, and they contain:

   - usb gadget driver fixes

   - xhci driver fixes

   - typec fixes

   - new quirks and ids

   - fixes for USB patches that went into 5.9-rc1.

  All of these have been tested in linux-next with no reported issues"

* tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
  usb: storage: Add unusual_uas entry for Sony PSZ drives
  USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge
  usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe()
  USB: gadget: u_f: Unbreak offset calculation in VLAs
  USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D
  usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures
  USB: PHY: JZ4770: Fix static checker warning.
  USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()
  USB: gadget: u_f: add overflow checks to VLA macros
  xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed
  xhci: Do warm-reset when both CAS and XDEV_RESUME are set
  usb: host: xhci: fix ep context print mismatch in debugfs
  usb: uas: Add quirk for PNY Pro Elite
  tools: usb: move to tools buildsystem
  USB: Fix device driver race
  USB: Also match device drivers using the ->match vfunc
  usb: host: xhci-tegra: fix tegra_xusb_get_phy()
  usb: host: xhci-tegra: otg usb2/usb3 port init
  usb: hcd: Fix use after free in usb_hcd_pci_remove()
  usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port()
  ...
2020-08-30 10:51:03 -07:00
Alan Stern
20934c0de1 usb: storage: Add unusual_uas entry for Sony PSZ drives
The PSZ-HA* family of USB disk drives from Sony can't handle the
REPORT OPCODES command when using the UAS protocol.  This patch adds
an appropriate quirks entry.

Reported-and-tested-by: Till Dörges <doerges@pre-sense.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200826143229.GB400430@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-28 09:23:16 +02:00
Cyril Roelandt
9aa37788e7 USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge
This device does not support UAS properly and a similar entry already
exists in drivers/usb/storage/unusual_uas.h. Without this patch,
storage_probe() defers the handling of this device to UAS, which cannot
handle it either.

Tested-by: Brice Goglin <brice.goglin@gmail.com>
Fixes: bc3bdb12bb ("usb-storage: Disable UAS on JMicron SATA enclosure")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Link: https://lore.kernel.org/r/20200825212231.46309-1-tipecaml@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-27 09:26:00 +02:00
Tang Bin
1d41698346 usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe()
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
exynos_ohci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.

Fixes: 62194244cf ("USB: Add Samsung Exynos OHCI diver")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200826144931.1828-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-27 09:25:58 +02:00
Andy Shevchenko
bfd08d06d9 USB: gadget: u_f: Unbreak offset calculation in VLAs
Inadvertently the commit b1cd1b65af ("USB: gadget: u_f: add overflow checks
to VLA macros") makes VLA macros to always return 0 due to different scope of
two variables of the same name. Obviously we need to have only one.

Fixes: b1cd1b65af ("USB: gadget: u_f: add overflow checks to VLA macros")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20200826192119.56450-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-27 09:25:06 +02:00
Alan Stern
068834a277 USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D
The Sound Devices MixPre-D audio card suffers from the same defect
as the Sound Devices USBPre2: an endpoint shared between a normal
audio interface and a vendor-specific interface, in violation of the
USB spec.  Since the USB core now treats duplicated endpoints as bugs
and ignores them, the audio endpoint isn't available and the card
can't be used for audio capture.

Along the same lines as commit bdd1b147b8 ("USB: quirks: blacklist
duplicate ep on Sound Devices USBPre2"), this patch adds a quirks
entry saying to ignore ep5in for interface 1, leaving it available for
use with standard audio interface 2.

Reported-and-tested-by: Jean-Christophe Barnoud <jcbarnoud@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Fixes: 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
Link: https://lore.kernel.org/r/20200826194624.GA412633@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-27 09:24:05 +02:00
Badhri Jagan Sridharan
23e26d0577 usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures
The patch addresses the compliance test failures while running  TDA
2.3.1.1 and  TDA 2.3.1.2 of the "PD Communications Engine USB PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.

While the purpose of TDA 2.3.1.1 and  TDA 2.3.1.2 is to verify that
the static and dynamic electrical capabilities of a Source meet the
requirements for each PDO offered,  while doing so, the tests also
monitor that the timing of the VBUS waveform versus the messages meets
the requirements for Hard Reset defined in PROT-PROC-HR-TSTR as
mentioned in step 11 of TDA.2.3.1.1 and step 15 of TDA.2.3.1.2.

TDB.2.2.13.1: PROT-PROC-HR-TSTR Procedure and Checks for Tester
Originated Hard Reset
Purpose: To perform the appropriate protocol checks relating to any
circumstance in which the Hard Reset signal is sent by the Tester.

UUT is behaving as source:
The Tester sends a Hard Reset signal.
1. Check VBUS stays within present valid voltage range for
tPSHardReset min (25ms) after last bit of Hard Reset signal.
[PROT_PROC_HR_TSTR_1]
2. Check that VBUS starts to fall below present valid voltage range by
tPSHardReset max (35ms). [PROT_PROC_HR_TSTR_2]
3. Check that VBUS reaches vSafe0V within tSafe0v max (650 ms).
[PROT_PROC_HR_TSTR_3]
4. Check that VBUS starts rising to vSafe5V after a delay of
tSrcRecover (0.66s - 1s) from reaching vSafe0V. [PROT_PROC_HR_TSTR_4]
5. Check that VBUS reaches vSafe5V within tSrcTurnOn max (275ms) of
rising above vSafe0v max (0.8V). [PROT_PROC_HR_TSTR_5] Power Delivery
Compliance Plan 139 6. Check that Source Capabilities are finished
sending within tFirstSourceCap max (250ms) of VBUS reaching vSafe5v
min. [PROT_PROC_HR_TSTR_6].

This is in line with 7.1.5 Response to Hard Resets of the USB Power
Delivery Specification Revision 3.0, Version 1.2,
"Hard Reset Signaling indicates a communication failure has occurred
and the Source Shall stop driving VCONN, Shall remove Rp from the
VCONN pin and Shall drive VBUS to vSafe0V as shown in Figure 7-9. The
USB connection May reset during a Hard Reset since the VBUS voltage
will be less than vSafe5V for an extended period of time. After
establishing the vSafe0V voltage condition on VBUS, the Source Shall
wait tSrcRecover before re-applying VCONN and restoring VBUS to
vSafe5V. A Source Shall conform to the VCONN timing as specified in
[USB Type-C 1.3]."

With the above guidelines from the spec in mind, TCPM does not turn
off VCONN while entering SRC_HARD_RESET_VBUS_OFF. The patch makes TCPM
turn off VCONN while entering SRC_HARD_RESET_VBUS_OFF and turn it back
on while entering SRC_HARD_RESET_VBUS_ON along with vbus instead of
having VCONN on through hardreset.

Also, the spec clearly states that "After establishing the vSafe0V
voltage condition on VBUS",  the Source Shall wait tSrcRecover before
re-applying VCONN and restoring VBUS to vSafe5V.
TCPM does not conform to this requirement. If the TCPC driver calls
tcpm_vbus_change with vbus off signal, TCPM right away enters
SRC_HARD_RESET_VBUS_ON without waiting for tSrcRecover.
For TCPC's which are buggy/does not call tcpm_vbus_change, TCPM
assumes that the vsafe0v is instantaneous as TCPM only waits
tSrcRecover instead of waiting for tSafe0v + tSrcRecover.
This patch also fixes this behavior by making sure that TCPM waits for
tSrcRecover before transitioning into SRC_HARD_RESET_VBUS_ON when
tcpm_vbus_change is called by TCPC.
When TCPC does not call tcpm_vbus_change, TCPM assumes the worst case
i.e.  tSafe0v + tSrcRecover before transitioning into
SRC_HARD_RESET_VBUS_ON.

Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20200817184601.1899929-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-25 16:02:35 +02:00
周琰杰 (Zhou Yanjie)
41dd70b368 USB: PHY: JZ4770: Fix static checker warning.
The commit 2a6c0b82e6 ("USB: PHY: JZ4770: Add support for new
Ingenic SoCs.") introduced the initialization function for different
chips, but left the relevant code involved in the resetting process
in the original function, resulting in uninitialized variable calls.

Fixes: 2a6c0b82e6 ("USB: PHY: JZ4770: Add support for new Ingenic SoCs.").
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200825081654.18186-2-zhouyanjie@wanyeetech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-25 16:02:34 +02:00
Brooke Basile
2b74b0a04d USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()
Some values extracted by ncm_unwrap_ntb() could possibly lead to several
different out of bounds reads of memory.  Specifically the values passed
to netdev_alloc_skb_ip_align() need to be checked so that memory is not
overflowed.

Resolve this by applying bounds checking to a number of different
indexes and lengths of the structure parsing logic.

Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Brooke Basile <brookebasile@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-25 16:02:32 +02:00
Brooke Basile
b1cd1b65af USB: gadget: u_f: add overflow checks to VLA macros
size can potentially hold an overflowed value if its assigned expression
is left unchecked, leading to a smaller than needed allocation when
vla_group_size() is used by callers to allocate memory.
To fix this, add a test for saturation before declaring variables and an
overflow check to (n) * sizeof(type).
If the expression results in overflow, vla_group_size() will return SIZE_MAX.

Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Brooke Basile <brookebasile@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-25 16:02:29 +02:00
Patrick Riphagen
6ccc48e0eb USB: serial: ftdi_sio: add IDs for Xsens Mti USB converter
The device added has an FTDI chip inside.
The device is used to connect Xsens USB Motion Trackers.

Cc: stable@vger.kernel.org
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
2020-08-24 10:18:30 +02:00
Gustavo A. R. Silva
df561f6688 treewide: Use fallthrough pseudo-keyword
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-23 17:36:59 -05:00
Ding Hui
f1ec7ae6c9 xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed
Some device drivers call libusb_clear_halt when target ep queue
is not empty. (eg. spice client connected to qemu for usb redir)

Before commit f5249461b5 ("xhci: Clear the host side toggle
manually when endpoint is soft reset"), that works well.
But now, we got the error log:

    EP not empty, refuse reset

xhci_endpoint_reset failed and left ep_state's EP_SOFT_CLEAR_TOGGLE
bit still set

So all the subsequent urb sumbits to the ep will fail with the
warn log:

    Can't enqueue URB while manually clearing toggle

We need to clear ep_state EP_SOFT_CLEAR_TOGGLE bit after
xhci_endpoint_reset, even if it failed.

Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: stable <stable@vger.kernel.org> # v4.17+
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-23 17:12:58 +02:00
Kai-Heng Feng
904df64a5f xhci: Do warm-reset when both CAS and XDEV_RESUME are set
Sometimes re-plugging a USB device during system sleep renders the device
useless:
[  173.418345] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x14203e2, return 0x10262
...
[  176.496485] usb 2-4: Waited 2000ms for CONNECT
[  176.496781] usb usb2-port4: status 0000.0262 after resume, -19
[  176.497103] usb 2-4: can't resume, status -19
[  176.497438] usb usb2-port4: logical disconnect

Because PLS equals to XDEV_RESUME, xHCI driver reports U3 to usbcore,
despite of CAS bit is flagged.

So proritize CAS over XDEV_RESUME to let usbcore handle warm-reset for
the port.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-23 17:12:13 +02:00
Li Jun
0077b1b2c8 usb: host: xhci: fix ep context print mismatch in debugfs
dci is 0 based and xhci_get_ep_ctx() will do ep index increment to get
the ep context.

[rename dci to ep_index -Mathias]
Cc: stable <stable@vger.kernel.org> # v4.15+
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-23 17:12:13 +02:00
Thinh Nguyen
9a469bc9f3 usb: uas: Add quirk for PNY Pro Elite
PNY Pro Elite USB 3.1 Gen 2 device (SSD) doesn't respond to ATA_12
pass-through command (i.e. it just hangs). If it doesn't support this
command, it should respond properly to the host. Let's just add a quirk
to be able to move forward with other operations.

Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Link: https://lore.kernel.org/r/2b0585228b003eedcc82db84697b31477df152e0.1597803605.git.thinhn@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-19 14:12:37 +02:00
Greg Kroah-Hartman
ab565f7eb1 USB: fixes for v5.9-rc
Three ZLP fixes on dwc3 and a resource leak fix on the TCM gadget
 
 Signed-off-by: Felipe Balbi <balbi@kernel.org>
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEElLzh7wn96CXwjh2IzL64meEamQYFAl89EigACgkQzL64meEa
 mQayZQ//ZQlAanidHwftPwAge1jkzs/S3Z14FvP9Etj/I65OYjDKmtHnQuM25/X6
 Ih5+HPMTOJXtEiNoljrQrSdXN0c2BMBeUDXS0PknXnjZaKZDd0xWd35llBYD46J8
 IpQBFsOARIwIIxO79z2iqhjUG6jGsAFSTL0WPJYusGW00Eh0DcSeF6VyBmHSc1D1
 xZLvrZ8xIq/tHkwRt0J4CrppIGM9kmjT87fFkGy2no1KpzEQ2jq0ipE3pBHMSEJ8
 hhA4aGykl04/kPyngcCFiXO2PGOhE+SuiyGnXmMNTb+dLAYP1KQDC3Vj+kDtEHlo
 CyO5UyNlH2U8MKwTpXb2qwf+7ky8MHvs2INfnePDgPfanDQuYiCCf8j/Y3DgGUkE
 WAgq0FY49gInHRMncwA2e8jS0nPb892MdHxjx5vft1m46hK/ME5i6J3BKH1pMZUZ
 yg1C1bnapsK9P+3U+aNJH5aORxSeWz5fjICLgPT26c3WVRZJfzKQaI44V6XKqsX1
 CEfYE1QoRDaEf4bhVKddrfR6ASw2hn3wkWs6Y0NU7c1Uyx2NcMkKzGLSV+HVRGWd
 +svP0efqB/tO/yrhljlt3LlmhX6a3rRg0mwgCyyoxpAt8Mr8IpbAvvuMFVDfNKDL
 dcVh7BmWs0r/VbA0bGRqfIqC63lLr+HICLoc/ekmxf5UrroT2a0=
 =GSI6
 -----END PGP SIGNATURE-----

Merge tag 'fixes-for-v5.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

USB: fixes for v5.9-rc

Three ZLP fixes on dwc3 and a resource leak fix on the TCM gadget

Signed-off-by: Felipe Balbi <balbi@kernel.org>

* tag 'fixes-for-v5.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
  usb: dwc3: gadget: Handle ZLP for sg requests
  usb: dwc3: gadget: Fix handling ZLP
  usb: dwc3: gadget: Don't setup more than requested
  usb: gadget: f_tcm: Fix some resource leaks in some error paths
2020-08-19 14:09:37 +02:00
Bastien Nocera
d5643d2249 USB: Fix device driver race
When a new device with a specialised device driver is plugged in, the
new driver will be modprobe()'d but the driver core will attach the
"generic" driver to the device.

After that, nothing will trigger a reprobe when the modprobe()'d device
driver has finished initialising, as the device has the "generic"
driver attached to it.

Trigger a reprobe ourselves when new specialised drivers get registered.

Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200818110445.509668-3-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 13:09:31 +02:00
Bastien Nocera
adb6e6ac20 USB: Also match device drivers using the ->match vfunc
We only ever used the ID table matching before, but we should also support
open-coded match functions.

Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200818110445.509668-1-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 13:08:45 +02:00
JC Kuo
d54343a877 usb: host: xhci-tegra: fix tegra_xusb_get_phy()
tegra_xusb_get_phy() should take input argument "name".

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200811092553.657762-1-jckuo@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 13:06:30 +02:00
JC Kuo
316a2868bc usb: host: xhci-tegra: otg usb2/usb3 port init
tegra_xusb_init_usb_phy() should initialize "otg_usb2_port" and
"otg_usb3_port" with -EINVAL because "0" is a valid value
represents usb2 port 0 or usb3 port 0.

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200811093143.699541-1-jckuo@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 13:06:29 +02:00
Andy Shevchenko
7b2816dd29 usb: hcd: Fix use after free in usb_hcd_pci_remove()
On the removal stage we put a reference to the controller structure and
if it's not used anymore it gets freed, but later we try to dereference
a pointer to a member of that structure.

Copy necessary field to a temporary variable to avoid use after free.

Fixes: 306c54d0ed ("usb: hcd: Try MSI interrupts on PCI devices")
Reported-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/linux-usb/30a8c4ca-64c2-863b-cfcd-0970599c0ba3@huawei.com/
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200814182218.71957-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 12:09:52 +02:00
Hans de Goede
bed97b3096 usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port()
Commit 081da1325d ("usb: typec: ucsi: displayport: Fix a potential race
during registration") made the ucsi code hold con->lock in
ucsi_register_displayport(). But we really don't want any interactions
with the connector to run before the port-registration process is fully
complete.

This commit moves the taking of con->lock from ucsi_register_displayport()
into ucsi_register_port() to achieve this.

Cc: stable@vger.kernel.org
Fixes: 081da1325d ("usb: typec: ucsi: displayport: Fix a potential race during registration")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-5-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 12:08:51 +02:00
Hans de Goede
25794e3079 usb: typec: ucsi: Rework ppm_lock handling
The ppm_lock really only needs to be hold during 2 functions:
ucsi_reset_ppm() and ucsi_run_command().

Push the taking of the lock down into these 2 functions, renaming
ucsi_run_command() to ucsi_send_command() which was an existing
wrapper already taking the lock for its callers.

This simplifies things for the callers and removes the difference
between ucsi_send_command() and ucsi_run_command() which has led
to various locking bugs in the past.

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 12:08:44 +02:00
Hans de Goede
7e90057f12 usb: typec: ucsi: Fix 2 unlocked ucsi_run_command calls
Fix 2 unlocked ucsi_run_command calls:

1. ucsi_handle_connector_change() contains one ucsi_send_command() call,
which takes the ppm_lock for it; and one ucsi_run_command() call which
relies on the caller have taking the ppm_lock.
ucsi_handle_connector_change() does not take the lock, so the
second (ucsi_run_command) calls should also be ucsi_send_command().

2. ucsi_get_pdos() gets called from ucsi_handle_connector_change() which
does not hold the ppm_lock, so it also must use ucsi_send_command().

This commit also adds a WARN_ON(!mutex_is_locked(&ucsi->ppm_lock)); to
ucsi_run_command() to avoid similar problems getting re-introduced in
the future.

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 12:07:42 +02:00
Hans de Goede
0ff0705a2e usb: typec: ucsi: Fix AB BA lock inversion
Lockdep reports an AB BA lock inversion between ucsi_init() and
ucsi_handle_connector_change():

AB order:

1. ucsi_init takes ucsi->ppm_lock (it runs with that locked for the
   duration of the function)
2. usci_init eventually end up calling ucsi_register_displayport,
   which takes ucsi_connector->lock

BA order:

1. ucsi_handle_connector_change work is started, takes ucsi_connector->lock
2. ucsi_handle_connector_change calls ucsi_send_command which takes
   ucsi->ppm_lock

The ppm_lock really only needs to be hold during 2 functions:
ucsi_reset_ppm() and ucsi_run_command().

This commit fixes the AB BA lock inversion by making ucsi_init drop the
ucsi->ppm_lock before it starts registering ports; and replacing any
ucsi_run_command() calls after this point with ucsi_send_command()
(which is a wrapper around run_command taking the lock while handling
the command).

Some of the replacing of ucsi_run_command with ucsi_send_command
in the helpers used during port registration also fixes a number of
code paths after registration which call ucsi_run_command() without
holding the ppm_lock:
1. ucsi_altmode_update_active() call in ucsi/displayport.c
2. ucsi_register_altmodes() call from ucsi_handle_connector_change()
   (through ucsi_partner_change())

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 12:07:42 +02:00
M. Vefa Bicakci
7a2f2974f2 usbip: Implement a match function to fix usbip
Commit 88b7381a93 ("USB: Select better matching USB drivers when
available") introduced the use of a "match" function to select a
non-generic/better driver for a particular USB device. This
unfortunately breaks the operation of usbip in general, as reported in
the kernel bugzilla with bug 208267 (linked below).

Upon inspecting the aforementioned commit, one can observe that the
original code in the usb_device_match function used to return 1
unconditionally, but the aforementioned commit makes the usb_device_match
function use identifier tables and "match" virtual functions, if either of
them are available.

Hence, this commit implements a match function for usbip that
unconditionally returns true to ensure that usbip is functional again.

This change has been verified to restore usbip functionality, with a
v5.7.y kernel on an up-to-date version of Qubes OS 4.0, which uses
usbip to redirect USB devices between VMs.

Thanks to Jonathan Dieter for the effort in bisecting this issue down
to the aforementioned commit.

Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208267
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1856443
Link: https://github.com/QubesOS/qubes-issues/issues/5905
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Cc: <stable@vger.kernel.org> # 5.7
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200810160017.46002-1-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 11:55:23 +02:00
Vinod Koul
d66a57be2f usb: renesas-xhci: remove version check
Some devices in wild are reporting bunch of firmware versions, so remove
the check for versions in driver

Reported by: Anastasios Vacharakis <vacharakis@gmail.com>
Reported by: Glen Journeay <journeay@gmail.com>
Fixes: 2478be82de ("usb: renesas-xhci: Add ROM loader for uPD720201")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=208911
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200818071739.789720-1-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 11:55:23 +02:00
Evgeny Novikov
531412492c USB: lvtest: return proper error code in probe
lvs_rh_probe() can return some nonnegative value from usb_control_msg()
when it is less than "USB_DT_HUB_NONVAR_SIZE + 2" that is considered as
a failure. Make lvs_rh_probe() return -EINVAL in this case.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200805090643.3432-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 11:55:23 +02:00
Tom Rix
f4b9d8a582 USB: cdc-acm: rework notification_buffer resizing
Clang static analysis reports this error

cdc-acm.c:409:3: warning: Use of memory after it is freed
        acm_process_notification(acm, (unsigned char *)dr);

There are three problems, the first one is that dr is not reset

The variable dr is set with

if (acm->nb_index)
	dr = (struct usb_cdc_notification *)acm->notification_buffer;

But if the notification_buffer is too small it is resized with

		if (acm->nb_size) {
			kfree(acm->notification_buffer);
			acm->nb_size = 0;
		}
		alloc_size = roundup_pow_of_two(expected_size);
		/*
		 * kmalloc ensures a valid notification_buffer after a
		 * use of kfree in case the previous allocation was too
		 * small. Final freeing is done on disconnect.
		 */
		acm->notification_buffer =
			kmalloc(alloc_size, GFP_ATOMIC);

dr should point to the new acm->notification_buffer.

The second problem is any data in the notification_buffer is lost
when the pointer is freed.  In the normal case, the current data
is accumulated in the notification_buffer here.

	memcpy(&acm->notification_buffer[acm->nb_index],
	       urb->transfer_buffer, copy_size);

When a resize happens, anything before
notification_buffer[acm->nb_index] is garbage.

The third problem is the acm->nb_index is not reset on a
resizing buffer error.

So switch resizing to using krealloc and reassign dr and
reset nb_index.

Fixes: ea2583529c ("cdc-acm: reassemble fragmented notifications")
Signed-off-by: Tom Rix <trix@redhat.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200801152154.20683-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 11:55:23 +02:00
Kai-Heng Feng
5967116e83 USB: quirks: Add no-lpm quirk for another Raydium touchscreen
There's another Raydium touchscreen needs the no-lpm quirk:
[    1.339149] usb 1-9: New USB device found, idVendor=2386, idProduct=350e, bcdDevice= 0.00
[    1.339150] usb 1-9: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.339151] usb 1-9: Product: Raydium Touch System
[    1.339152] usb 1-9: Manufacturer: Raydium Corporation
...
[    6.450497] usb 1-9: can't set config #1, error -110

BugLink: https://bugs.launchpad.net/bugs/1889446
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200731051622.28643-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 11:55:23 +02:00
Alan Stern
f176ede3a3 USB: yurex: Fix bad gfp argument
The syzbot fuzzer identified a bug in the yurex driver: It passes
GFP_KERNEL as a memory-allocation flag to usb_submit_urb() at a time
when its state is TASK_INTERRUPTIBLE, not TASK_RUNNING:

do not call blocking ops when !TASK_RUNNING; state=1 set at [<00000000370c7c68>] prepare_to_wait+0xb1/0x2a0 kernel/sched/wait.c:247
WARNING: CPU: 1 PID: 340 at kernel/sched/core.c:7253 __might_sleep+0x135/0x190
kernel/sched/core.c:7253
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 340 Comm: syz-executor677 Not tainted 5.8.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0xf6/0x16e lib/dump_stack.c:118
 panic+0x2aa/0x6e1 kernel/panic.c:231
 __warn.cold+0x20/0x50 kernel/panic.c:600
 report_bug+0x1bd/0x210 lib/bug.c:198
 handle_bug+0x41/0x80 arch/x86/kernel/traps.c:234
 exc_invalid_op+0x14/0x40 arch/x86/kernel/traps.c:254
 asm_exc_invalid_op+0x12/0x20 arch/x86/include/asm/idtentry.h:536
RIP: 0010:__might_sleep+0x135/0x190 kernel/sched/core.c:7253
Code: 65 48 8b 1c 25 40 ef 01 00 48 8d 7b 10 48 89 fe 48 c1 ee 03 80 3c 06 00 75
2b 48 8b 73 10 48 c7 c7 e0 9e 06 86 e8 ed 12 f6 ff <0f> 0b e9 46 ff ff ff e8 1f
b2 4b 00 e9 29 ff ff ff e8 15 b2 4b 00
RSP: 0018:ffff8881cdb77a28 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffff8881c6458000 RCX: 0000000000000000
RDX: ffff8881c6458000 RSI: ffffffff8129ec93 RDI: ffffed1039b6ef37
RBP: ffffffff86fdade2 R08: 0000000000000001 R09: ffff8881db32f54f
R10: 0000000000000000 R11: 0000000030343354 R12: 00000000000001f2
R13: 0000000000000000 R14: 0000000000000068 R15: ffffffff83c1b1aa
 slab_pre_alloc_hook.constprop.0+0xea/0x200 mm/slab.h:498
 slab_alloc_node mm/slub.c:2816 [inline]
 slab_alloc mm/slub.c:2900 [inline]
 kmem_cache_alloc_trace+0x46/0x220 mm/slub.c:2917
 kmalloc include/linux/slab.h:554 [inline]
 dummy_urb_enqueue+0x7a/0x880 drivers/usb/gadget/udc/dummy_hcd.c:1251
 usb_hcd_submit_urb+0x2b2/0x22d0 drivers/usb/core/hcd.c:1547
 usb_submit_urb+0xb4e/0x13e0 drivers/usb/core/urb.c:570
 yurex_write+0x3ea/0x820 drivers/usb/misc/yurex.c:495

This patch changes the call to use GFP_ATOMIC instead of GFP_KERNEL.

Reported-and-tested-by: syzbot+c2c3302f9c601a4b1be2@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200810182954.GB307778@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 11:48:57 +02:00
Thinh Nguyen
bc9a2e226e usb: dwc3: gadget: Handle ZLP for sg requests
Currently dwc3 doesn't handle usb_request->zero for SG requests. This
change checks and prepares extra TRBs for the ZLP for SG requests.

Cc: <stable@vger.kernel.org> # v4.5+
Fixes: 04c03d10e5 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-08-17 15:22:08 +03:00