Loading CR3 as part of emulating vmentry is different from regular CR3 loads,
as implemented in kvm_set_cr3, in several ways.
* different rules are followed to check CR3 and it is desirable for the caller
to distinguish between the possible failures
* PDPTRs are not loaded if PAE paging and nested EPT are both enabled
* many MMU operations are not necessary
This patch introduces nested_vmx_load_cr3 suitable for CR3 loads as part of
nested vmentry and vmexit, and makes use of it on the nested vmentry path.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
It is possible that prepare_vmcs02 fails to load the guest state. This
patch adds the proper error handling for such a case. L1 will receive
an INVALID_STATE vmexit with the appropriate exit qualification if it
happens.
A failure to set guest CR3 is the only error propagated from prepare_vmcs02
at the moment.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
KVM does not correctly handle L1 hypervisors that emulate L2 real mode with
PAE and EPT, such as Hyper-V. In this mode, the L1 hypervisor populates guest
PDPTE VMCS fields and leaves guest CR3 uninitialized because it is not used
(see 26.3.2.4 Loading Page-Directory-Pointer-Table Entries). KVM always
dereferences CR3 and tries to load PDPTEs if PAE is on. This leads to two
related issues:
1) On the first nested vmentry, the guest PDPTEs, as populated by L1, are
overwritten in ept_load_pdptrs because the registers are believed to have
been loaded in load_pdptrs as part of kvm_set_cr3. This is incorrect. L2 is
running with PAE enabled but PDPTRs have been set up by L1.
2) When L2 is about to enable paging and loads its CR3, we, again, attempt
to load PDPTEs in load_pdptrs called from kvm_set_cr3. There are no guarantees
that this will succeed (it's just a CR3 load, paging is not enabled yet) and
if it doesn't, kvm_set_cr3 returns early without persisting the CR3 which is
then lost and L2 crashes right after it enables paging.
This patch replaces the kvm_set_cr3 call with a simple register write if PAE
and EPT are both on. CR3 is not to be interpreted in this case.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
vmx_set_cr0() modifies GUEST_EFER and "IA-32e mode guest" in the current
VMCS. Call vmx_set_efer() after vmx_set_cr0() so that emulated VM-entry
is more faithful to VMCS12.
This patch correctly causes VM-entry to fail when "IA-32e mode guest" is
1 and GUEST_CR0.PG is 0. Previously this configuration would succeed and
"IA-32e mode guest" would silently be disabled by KVM.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
MSR_IA32_CR{0,4}_FIXED1 define which bits in CR0 and CR4 are allowed to
be 1 during VMX operation. Since the set of allowed-1 bits is the same
in and out of VMX operation, we can generate these MSRs entirely from
the guest's CPUID. This lets userspace avoiding having to save/restore
these MSRs.
This patch also initializes MSR_IA32_CR{0,4}_FIXED1 from the CPU's MSRs
by default. This is a saner than the current default of -1ull, which
includes bits that the host CPU does not support.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
KVM emulates MSR_IA32_VMX_CR{0,4}_FIXED1 with the value -1ULL, meaning
all CR0 and CR4 bits are allowed to be 1 during VMX operation.
This does not match real hardware, which disallows the high 32 bits of
CR0 to be 1, and disallows reserved bits of CR4 to be 1 (including bits
which are defined in the SDM but missing according to CPUID). A guest
can induce a VM-entry failure by setting these bits in GUEST_CR0 and
GUEST_CR4, despite MSR_IA32_VMX_CR{0,4}_FIXED1 indicating they are
valid.
Since KVM has allowed all bits to be 1 in CR0 and CR4, the existing
checks on these registers do not verify must-be-0 bits. Fix these checks
to identify must-be-0 bits according to MSR_IA32_VMX_CR{0,4}_FIXED1.
This patch should introduce no change in behavior in KVM, since these
MSRs are still -1ULL.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The VMX capability MSRs advertise the set of features the KVM virtual
CPU can support. This set of features varies across different host CPUs
and KVM versions. This patch aims to addresses both sources of
differences, allowing VMs to be migrated across CPUs and KVM versions
without guest-visible changes to these MSRs. Note that cross-KVM-
version migration is only supported from this point forward.
When the VMX capability MSRs are restored, they are audited to check
that the set of features advertised are a subset of what KVM and the
CPU support.
Since the VMX capability MSRs are read-only, they do not need to be on
the default MSR save/restore lists. The userspace hypervisor can set
the values of these MSRs or read them from KVM at VCPU creation time,
and restore the same value after every save/restore.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The "non-true" VMX capability MSRs can be generated from their "true"
counterparts, by OR-ing the default1 bits. The default1 bits are fixed
and defined in the SDM.
Since we can generate the non-true VMX MSRs from the true versions,
there's no need to store both in struct nested_vmx. This also lets
userspace avoid having to restore the non-true MSRs.
Note this does not preclude emulating MSR_IA32_VMX_BASIC[55]=0. To do so,
we simply need to set all the default1 bits in the true MSRs (such that
the true MSRs and the generated non-true MSRs are equal).
Signed-off-by: David Matlack <dmatlack@google.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
kvm_skip_emulated_instruction calls both
kvm_x86_ops->skip_emulated_instruction and kvm_vcpu_check_singlestep,
skipping the emulated instruction and generating a trap if necessary.
Replacing skip_emulated_instruction calls with
kvm_skip_emulated_instruction is straightforward, except for:
- ICEBP, which is already inside a trap, so avoid triggering another trap.
- Instructions that can trigger exits to userspace, such as the IO insns,
MOVs to CR8, and HALT. If kvm_skip_emulated_instruction does trigger a
KVM_GUESTDBG_SINGLESTEP exit, and the handling code for
IN/OUT/MOV CR8/HALT also triggers an exit to userspace, the latter will
take precedence. The singlestep will be triggered again on the next
instruction, which is the current behavior.
- Task switch instructions which would require additional handling (e.g.
the task switch bit) and are instead left alone.
- Cases where VMLAUNCH/VMRESUME do not proceed to the next instruction,
which do not trigger singlestep traps as mentioned previously.
Signed-off-by: Kyle Huey <khuey@kylehuey.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
We can't return both the pass/fail boolean for the vmcs and the upcoming
continue/exit-to-userspace boolean for skip_emulated_instruction out of
nested_vmx_check_vmcs, so move skip_emulated_instruction out of it instead.
Additionally, VMENTER/VMRESUME only trigger singlestep exceptions when
they advance the IP to the following instruction, not when they a) succeed,
b) fail MSR validation or c) throw an exception. Add a separate call to
skip_emulated_instruction that will later not be converted to the variant
that checks the singlestep flag.
Signed-off-by: Kyle Huey <khuey@kylehuey.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The functions being moved ahead of skip_emulated_instruction here don't
need updated IPs, and skipping the emulated instruction at the end will
make it easier to return its value.
Signed-off-by: Kyle Huey <khuey@kylehuey.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Once skipping the emulated instruction can potentially trigger an exit to
userspace (via KVM_GUESTDBG_SINGLESTEP) kvm_emulate_cpuid will need to
propagate a return value.
Signed-off-by: Kyle Huey <khuey@kylehuey.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
- Expose all invalidation types to the L1
- Reject invvpid instruction, if L1 passed zero vpid value to single
context invalidations
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Tested-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
vmx_arm_hv_timer is only used in vmx.c, and should be static to
avoid compiling warning when with -Wmissing-prototypes option.
Signed-off-by: Jiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On some benchmarks (e.g. netperf with ioeventfd disabled), APICv
posted interrupts turn out to be slower than interrupt injection via
KVM_REQ_EVENT.
This patch optimizes a bit the IRR update, avoiding expensive atomic
operations in the common case where PI.ON=0 at vmentry or the PIR vector
is mostly zero. This saves at least 20 cycles (1%) per vmexit, as
measured by kvm-unit-tests' inl_from_qemu test (20 runs):
| enable_apicv=1 | enable_apicv=0
| mean stdev | mean stdev
----------|-----------------|------------------
before | 5826 32.65 | 5765 47.09
after | 5809 43.42 | 5777 77.02
Of course, any change in the right column is just placebo effect. :)
The savings are bigger if interrupts are frequent.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are never used by the host, but they can still be reflected to
the guest.
Tested-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since Paolo has removed irq-enable-operation in vmx_handle_external_intr
(KVM: x86: use guest_exit_irqoff), the original comment about the IF bit
in rflags is incorrect and stale now, so remove it.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
We've had 10 page-sized bitmaps that were being allocated and freed one
by one when we could just use a cycle.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
vmx_disable_intercept_msr_read_x2apic() and
vmx_disable_intercept_msr_write_x2apic() differed only in the type.
Pass the type to a new function.
[Ordered and commented TPR intercept according to Paolo's suggestion.]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
All intercepts are enabled at the beginning, so they can only be used if
we disabled an intercept that we wanted to have enabled.
This was done for TMCCT to simplify a loop that disables all x2APIC MSR
intercepts, but just keeping TMCCT enabled yields better results.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
When L0 establishes (or removes) an MSR entry in the VM-entry or VM-exit
MSR load lists, the change should affect the dormant VMCS as well as the
current VMCS. Moreover, the vmcs02 MSR-load addresses should be
initialized.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
When forwarding a hardware VM-entry failure to L1, fetch the
VM_INSTRUCTION_ERROR field from vmcs02 before loading vmcs01.
(Note that there is an implicit assumption that the VM-entry failure was
on the first VM-entry to vmcs02 after nested_vmx_run; otherwise, L1 is
going to be very confused.)
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Feiner <pfeiner@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Renames x2apic_apicv_inactive msr_bitmaps to x2apic and original
x2apic bitmaps to x2apic_apicv.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
After a successful VM-entry with the "VMCS shadowing" VM-execution
control set, the shadow VMCS referenced by the VMCS link pointer field
in the current VMCS becomes active on the logical processor.
A VMCS that is made active on more than one logical processor may become
corrupted. Therefore, before an active VMCS can be migrated to another
logical processor, the first logical processor must execute a VMCLEAR
for the active VMCS. VMCLEAR both ensures that all VMCS data are written
to memory and makes the VMCS inactive.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-By: David Matlack <dmatlack@google.com>
Message-Id: <1477668579-22555-1-git-send-email-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit a545ab6a00 ("kvm: x86: add tsc_offset field to struct
kvm_vcpu_arch", 2016-09-07) the offset between host and L1 TSC is
cached and need not be fished out of the VMCS or VMCB. This means
that we can implement adjust_tsc_offset_guest and read_l1_tsc
entirely in generic code. The simplification is particularly
significant for VMX code, where vmx->nested.vmcs01_tsc_offset
was duplicating what is now in vcpu->arch.tsc_offset. Therefore
the vmcs01_tsc_offset can be dropped completely.
More importantly, this fixes KVM_GET_CLOCK/KVM_SET_CLOCK
which, after commit 108b249c45 ("KVM: x86: introduce get_kvmclock_ns",
2016-09-01) called read_l1_tsc while the VMCS was not loaded.
It thus returned bogus values on Intel CPUs.
Fixes: 108b249c45
Reported-by: Roman Kagan <rkagan@virtuozzo.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that x86 always uses eager FPU switching on the host, there's no
need for KVM to manipulate the host's CR0.TS.
This should be both simpler and faster.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm list <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/b212064922537c05d0c81d931fc4dbe769127ce7.1477951965.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Bitwise shifts by amounts greater than or equal to the width of the left
operand are undefined. A malicious guest can exploit this to crash a
32-bit host, due to the BUG_ON(1)'s in handle_{invept,invvpid}.
Signed-off-by: Jim Mattson <jmattson@google.com>
Message-Id: <1477496318-17681-1-git-send-email-jmattson@google.com>
[Change 1UL to 1, to match the range check on the shift count. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All architectures:
Move `make kvmconfig` stubs from x86; use 64 bits for debugfs stats.
ARM:
Important fixes for not using an in-kernel irqchip; handle SError
exceptions and present them to guests if appropriate; proxying of GICV
access at EL2 if guest mappings are unsafe; GICv3 on AArch32 on ARMv8;
preparations for GICv3 save/restore, including ABI docs; cleanups and
a bit of optimizations.
MIPS:
A couple of fixes in preparation for supporting MIPS EVA host kernels;
MIPS SMP host & TLB invalidation fixes.
PPC:
Fix the bug which caused guests to falsely report lockups; other minor
fixes; a small optimization.
s390:
Lazy enablement of runtime instrumentation; up to 255 CPUs for nested
guests; rework of machine check deliver; cleanups and fixes.
x86:
IOMMU part of AMD's AVIC for vmexit-less interrupt delivery; Hyper-V
TSC page; per-vcpu tsc_offset in debugfs; accelerated INS/OUTS in
nVMX; cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJX9iDrAAoJEED/6hsPKofoOPoIAIUlgojkb9l2l1XVDgsXdgQL
sRVhYSVv7/c8sk9vFImrD5ElOPZd+CEAIqFOu45+NM3cNi7gxip9yftUVs7wI5aC
eDZRWm1E4trDZLe54ZM9ThcqZzZZiELVGMfR1+ZndUycybwyWzafpXYsYyaXp3BW
hyHM3qVkoWO3dxBWFwHIoO/AUJrWYkRHEByKyvlC6KPxSdBPSa5c1AQwMCoE0Mo4
K/xUj4gBn9eMelNhg4Oqu/uh49/q+dtdoP2C+sVM8bSdquD+PmIeOhPFIcuGbGFI
B+oRpUhIuntN39gz8wInJ4/GRSeTuR2faNPxMn4E1i1u4LiuJvipcsOjPfe0a18=
=fZRB
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.9-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"All architectures:
- move `make kvmconfig` stubs from x86
- use 64 bits for debugfs stats
ARM:
- Important fixes for not using an in-kernel irqchip
- handle SError exceptions and present them to guests if appropriate
- proxying of GICV access at EL2 if guest mappings are unsafe
- GICv3 on AArch32 on ARMv8
- preparations for GICv3 save/restore, including ABI docs
- cleanups and a bit of optimizations
MIPS:
- A couple of fixes in preparation for supporting MIPS EVA host
kernels
- MIPS SMP host & TLB invalidation fixes
PPC:
- Fix the bug which caused guests to falsely report lockups
- other minor fixes
- a small optimization
s390:
- Lazy enablement of runtime instrumentation
- up to 255 CPUs for nested guests
- rework of machine check deliver
- cleanups and fixes
x86:
- IOMMU part of AMD's AVIC for vmexit-less interrupt delivery
- Hyper-V TSC page
- per-vcpu tsc_offset in debugfs
- accelerated INS/OUTS in nVMX
- cleanups and fixes"
* tag 'kvm-4.9-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (140 commits)
KVM: MIPS: Drop dubious EntryHi optimisation
KVM: MIPS: Invalidate TLB by regenerating ASIDs
KVM: MIPS: Split kernel/user ASID regeneration
KVM: MIPS: Drop other CPU ASIDs on guest MMU changes
KVM: arm/arm64: vgic: Don't flush/sync without a working vgic
KVM: arm64: Require in-kernel irqchip for PMU support
KVM: PPC: Book3s PR: Allow access to unprivileged MMCR2 register
KVM: PPC: Book3S PR: Support 64kB page size on POWER8E and POWER8NVL
KVM: PPC: Book3S: Remove duplicate setting of the B field in tlbie
KVM: PPC: BookE: Fix a sanity check
KVM: PPC: Book3S HV: Take out virtual core piggybacking code
KVM: PPC: Book3S: Treat VTB as a per-subcore register, not per-thread
ARM: gic-v3: Work around definition of gic_write_bpr1
KVM: nVMX: Fix the NMI IDT-vectoring handling
KVM: VMX: Enable MSR-BASED TPR shadow even if APICv is inactive
KVM: nVMX: Fix reload apic access page warning
kvmconfig: add virtio-gpu to config fragment
config: move x86 kvm_guest.config to a common location
arm64: KVM: Remove duplicating init code for setting VMID
ARM: KVM: Support vgic-v3
...
Run kvm-unit-tests/eventinj.flat in L1:
Sending NMI to self
After NMI to self
FAIL: NMI
This test scenario is to test whether VMM can handle NMI IDT-vectoring info correctly.
At the beginning, L2 writes LAPIC to send a self NMI, the EPT page tables on both L1
and L0 are empty so:
- The L2 accesses memory can generate EPT violation which can be intercepted by L0.
The EPT violation vmexit occurred during delivery of this NMI, and the NMI info is
recorded in vmcs02's IDT-vectoring info.
- L0 walks L1's EPT12 and L0 sees the mapping is invalid, it injects the EPT violation into L1.
The vmcs02's IDT-vectoring info is reflected to vmcs12's IDT-vectoring info since
it is a nested vmexit.
- L1 receives the EPT violation, then fixes its EPT12.
- L1 executes VMRESUME to resume L2 which generates vmexit and causes L1 exits to L0.
- L0 emulates VMRESUME which is called from L1, then return to L2.
L0 merges the requirement of vmcs12's IDT-vectoring info and injects it to L2 through
vmcs02.
- The L2 re-executes the fault instruction and cause EPT violation again.
- Since the L1's EPT12 is valid, L0 can fix its EPT02
- L0 resume L2
The EPT violation vmexit occurred during delivery of this NMI again, and the NMI info
is recorded in vmcs02's IDT-vectoring info. L0 should inject the NMI through vmentry
event injection since it is caused by EPT02's EPT violation.
However, vmx_inject_nmi() refuses to inject NMI from IDT-vectoring info if vCPU is in
guest mode, this patch fix it by permitting to inject NMI from IDT-vectoring if it is
the L0's responsibility to inject NMI from IDT-vectoring info to L2.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Bandan Das <bsd@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
I observed that kvmvapic(to optimize flexpriority=N or AMD) is used
to boost TPR access when testing kvm-unit-test/eventinj.flat tpr case
on my haswell desktop (w/ flexpriority, w/o APICv). Commit (8d14695f95
x86, apicv: add virtual x2apic support) disable virtual x2apic mode
completely if w/o APICv, and the author also told me that windows guest
can't enter into x2apic mode when he developed the APICv feature several
years ago. However, it is not truth currently, Interrupt Remapping and
vIOMMU is added to qemu and the developers from Intel test windows 8 can
work in x2apic mode w/ Interrupt Remapping enabled recently.
This patch enables TPR shadow for virtual x2apic mode to boost
windows guest in x2apic mode even if w/o APICv.
Can pass the kvm-unit-test.
Suggested-by: Radim Krčmář <rkrcmar@redhat.com>
Suggested-by: Wincy Van <fanwenyi0529@gmail.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Wincy Van <fanwenyi0529@gmail.com>
Cc: Yang Zhang <yang.zhang.wz@gmail.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
WARNING: CPU: 1 PID: 4230 at kernel/sched/core.c:7564 __might_sleep+0x7e/0x80
do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffff8d0de7f9>] prepare_to_swait+0x39/0xa0
CPU: 1 PID: 4230 Comm: qemu-system-x86 Not tainted 4.8.0-rc5+ #47
Call Trace:
dump_stack+0x99/0xd0
__warn+0xd1/0xf0
warn_slowpath_fmt+0x4f/0x60
? prepare_to_swait+0x39/0xa0
? prepare_to_swait+0x39/0xa0
__might_sleep+0x7e/0x80
__gfn_to_pfn_memslot+0x156/0x480 [kvm]
gfn_to_pfn+0x2a/0x30 [kvm]
gfn_to_page+0xe/0x20 [kvm]
kvm_vcpu_reload_apic_access_page+0x32/0xa0 [kvm]
nested_vmx_vmexit+0x765/0xca0 [kvm_intel]
? _raw_spin_unlock_irqrestore+0x36/0x80
vmx_check_nested_events+0x49/0x1f0 [kvm_intel]
kvm_arch_vcpu_runnable+0x2d/0xe0 [kvm]
kvm_vcpu_check_block+0x12/0x60 [kvm]
kvm_vcpu_block+0x94/0x4c0 [kvm]
kvm_arch_vcpu_ioctl_run+0x619/0x1aa0 [kvm]
? kvm_arch_vcpu_ioctl_run+0xdf1/0x1aa0 [kvm]
kvm_vcpu_ioctl+0x2d3/0x7c0 [kvm]
===============================
[ INFO: suspicious RCU usage. ]
4.8.0-rc5+ #47 Not tainted
-------------------------------
./include/linux/kvm_host.h:535 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
1 lock held by qemu-system-x86/4230:
#0: (&vcpu->mutex){+.+.+.}, at: [<ffffffffc062975c>] vcpu_load+0x1c/0x60 [kvm]
stack backtrace:
CPU: 1 PID: 4230 Comm: qemu-system-x86 Not tainted 4.8.0-rc5+ #47
Call Trace:
dump_stack+0x99/0xd0
lockdep_rcu_suspicious+0xe7/0x120
gfn_to_memslot+0x12a/0x140 [kvm]
gfn_to_pfn+0x12/0x30 [kvm]
gfn_to_page+0xe/0x20 [kvm]
kvm_vcpu_reload_apic_access_page+0x32/0xa0 [kvm]
nested_vmx_vmexit+0x765/0xca0 [kvm_intel]
? _raw_spin_unlock_irqrestore+0x36/0x80
vmx_check_nested_events+0x49/0x1f0 [kvm_intel]
kvm_arch_vcpu_runnable+0x2d/0xe0 [kvm]
kvm_vcpu_check_block+0x12/0x60 [kvm]
kvm_vcpu_block+0x94/0x4c0 [kvm]
kvm_arch_vcpu_ioctl_run+0x619/0x1aa0 [kvm]
? kvm_arch_vcpu_ioctl_run+0xdf1/0x1aa0 [kvm]
kvm_vcpu_ioctl+0x2d3/0x7c0 [kvm]
? __fget+0xfd/0x210
? __lock_is_held+0x54/0x70
do_vfs_ioctl+0x96/0x6a0
? __fget+0x11c/0x210
? __fget+0x5/0x210
SyS_ioctl+0x79/0x90
do_syscall_64+0x81/0x220
entry_SYSCALL64_slow_path+0x25/0x25
These can be triggered by running kvm-unit-test: ./x86-run x86/vmx.flat
The nested preemption timer is based on hrtimer which is started on L2
entry, stopped on L2 exit and evaluated via the new check_nested_events
hook. The current logic adds vCPU to a simple waitqueue (TASK_INTERRUPTIBLE)
if need to yield pCPU and w/o holding srcu read lock when accesses memslots,
both can be in nested preemption timer evaluation path which results in
the warning above.
This patch fix it by leveraging request bit to async reload APIC access
page before vmentry in order to avoid to reload directly during the nested
preemption timer evaluation, it is safe since the vmcs01 is loaded and
current is nested vmexit.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Yunhong Jiang <yunhong.jiang@intel.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The TSC offset can now be read directly from struct kvm_arch_vcpu.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose the feature to L1 hypervisor if host CPU supports it, since
certain hypervisors requires it for own purposes.
According to Intel SDM A.1, if CPU supports the feature,
VMX_INSTRUCTION_INFO field of VMCS will contain detailed information
about INS/OUTS instructions handling. This field is already copied to
VMCS12 for L1 hypervisor (see prepare_vmcs12 routine) independently
feature presence.
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
setup_vmcs_config takes a pointer to the vmcs_config global. The
indirection is somewhat pointless, but just keep things consistent
for now.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are mostly related to nested VMX. They needn't have
a loglevel as high as KERN_WARN, and mustn't be allowed to
pollute the host logs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If EPT support is exposed to L1 hypervisor, guest linear-address field
of VMCS should contain GVA of L2, the access to which caused EPT violation.
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 61abdbe0bc ("kvm: x86: make lapic hrtimer pinned") pins the emulated
lapic timer. This patch does the same for the emulated nested preemption
timer to avoid vmexit an unrelated vCPU and the latency of kicking IPI to
another vCPU.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Yunhong Jiang <yunhong.jiang@intel.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The validity check for the guest line address is inefficient,
check the invalid value instead of enumerating the valid ones.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When the host supported TSC scaling, L2 would use a TSC multiplier of
0, which causes a VM entry failure. Now L2's TSC uses the same
multiplier as L1.
Signed-off-by: Peter Feiner <pfeiner@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If vmcs12 does not intercept APIC_BASE writes, then KVM will handle the
write with vmcs02 as the current VMCS.
This will incorrectly apply modifications intended for vmcs01 to vmcs02
and L2 can use it to gain access to L0's x2APIC registers by disabling
virtualized x2APIC while using msr bitmap that assumes enabled.
Postpone execution of vmx_set_virtual_x2apic_mode until vmcs01 is the
current VMCS. An alternative solution would temporarily make vmcs01 the
current VMCS, but it requires more care.
Fixes: 8d14695f95 ("x86, apicv: add virtual x2apic support")
Reported-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
msr bitmap can be used to avoid a VM exit (interception) on guest MSR
accesses. In some configurations of VMX controls, the guest can even
directly access host's x2APIC MSRs. See SDM 29.5 VIRTUALIZING MSR-BASED
APIC ACCESSES.
L2 could read all L0's x2APIC MSRs and write TPR, EOI, and SELF_IPI.
To do so, L1 would first trick KVM to disable all possible interceptions
by enabling APICv features and then would turn those features off;
nested_vmx_merge_msr_bitmap() only disabled interceptions, so VMX would
not intercept previously enabled MSRs even though they were not safe
with the new configuration.
Correctly re-enabling interceptions is not enough as a second bug would
still allow L1+L2 to access host's MSRs: msr bitmap was shared for all
VMCSs, so L1 could trigger a race to get the desired combination of msr
bitmap and VMX controls.
This fix allocates a msr bitmap for every L1 VCPU, allows only safe
x2APIC MSRs from L1's msr bitmap, and disables msr bitmaps if they would
have to intercept everything anyway.
Fixes: 3af18d9c5f ("KVM: nVMX: Prepare for using hardware MSR bitmap")
Reported-by: Jim Mattson <jmattson@google.com>
Suggested-by: Wincy Van <fanwenyi0529@gmail.com>
Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Guided by grsecurity's analogous __read_only markings in arch/x86,
this applies several uses of __ro_after_init to structures that are
only updated during __init, and const for some structures that are
never updated. Additionally extends __init markings to some functions
that are only used during __init, and cleans up some missing C99 style
static initializers.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Brown <david.brown@linaro.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Emese Revfy <re.emese@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathias Krause <minipli@googlemail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: PaX Team <pageexec@freemail.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-hardening@lists.openwall.com
Link: http://lkml.kernel.org/r/20160808232906.GA29731@www.outflux.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 4b85507860 ("KVM: nVMX: Don't advertise single
context invalidation for invept") removed advertising
single context invalidation since the spec does not mandate it.
However, some hypervisors (such as ESX) require it to be present
before willing to use ept in a nested environment. Advertise it
and fallback to the global case.
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nested vpid is already supported and both single/global
modes are advertised to the guest
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VGIC implementation.
- s390: support for trapping software breakpoints, nested virtualization
(vSIE), the STHYI opcode, initial extensions for CPU model support.
- MIPS: support for MIPS64 hosts (32-bit guests only) and lots of cleanups,
preliminary to this and the upcoming support for hardware virtualization
extensions.
- x86: support for execute-only mappings in nested EPT; reduced vmexit
latency for TSC deadline timer (by about 30%) on Intel hosts; support for
more than 255 vCPUs.
- PPC: bugfixes.
The ugly bit is the conflicts. A couple of them are simple conflicts due
to 4.7 fixes, but most of them are with other trees. There was definitely
too much reliance on Acked-by here. Some conflicts are for KVM patches
where _I_ gave my Acked-by, but the worst are for this pull request's
patches that touch files outside arch/*/kvm. KVM submaintainers should
probably learn to synchronize better with arch maintainers, with the
latter providing topic branches whenever possible instead of Acked-by.
This is what we do with arch/x86. And I should learn to refuse pull
requests when linux-next sends scary signals, even if that means that
submaintainers have to rebase their branches.
Anyhow, here's the list:
- arch/x86/kvm/vmx.c: handle_pcommit and EXIT_REASON_PCOMMIT was removed
by the nvdimm tree. This tree adds handle_preemption_timer and
EXIT_REASON_PREEMPTION_TIMER at the same place. In general all mentions
of pcommit have to go.
There is also a conflict between a stable fix and this patch, where the
stable fix removed the vmx_create_pml_buffer function and its call.
- virt/kvm/kvm_main.c: kvm_cpu_notifier was removed by the hotplug tree.
This tree adds kvm_io_bus_get_dev at the same place.
- virt/kvm/arm/vgic.c: a few final bugfixes went into 4.7 before the
file was completely removed for 4.8.
- include/linux/irqchip/arm-gic-v3.h: this one is entirely our fault;
this is a change that should have gone in through the irqchip tree and
pulled by kvm-arm. I think I would have rejected this kvm-arm pull
request. The KVM version is the right one, except that it lacks
GITS_BASER_PAGES_SHIFT.
- arch/powerpc: what a mess. For the idle_book3s.S conflict, the KVM
tree is the right one; everything else is trivial. In this case I am
not quite sure what went wrong. The commit that is causing the mess
(fd7bacbca4, "KVM: PPC: Book3S HV: Fix TB corruption in guest exit
path on HMI interrupt", 2016-05-15) touches both arch/powerpc/kernel/
and arch/powerpc/kvm/. It's large, but at 396 insertions/5 deletions
I guessed that it wasn't really possible to split it and that the 5
deletions wouldn't conflict. That wasn't the case.
- arch/s390: also messy. First is hypfs_diag.c where the KVM tree
moved some code and the s390 tree patched it. You have to reapply the
relevant part of commits 6c22c98637, plus all of e030c1125e, to
arch/s390/kernel/diag.c. Or pick the linux-next conflict
resolution from http://marc.info/?l=kvm&m=146717549531603&w=2.
Second, there is a conflict in gmap.c between a stable fix and 4.8.
The KVM version here is the correct one.
I have pushed my resolution at refs/heads/merge-20160802 (commit
3d1f53419842) at git://git.kernel.org/pub/scm/virt/kvm/kvm.git.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXoGm7AAoJEL/70l94x66DugQIAIj703ePAFepB/fCrKHkZZia
SGrsBdvAtNsOhr7FQ5qvvjLxiv/cv7CymeuJivX8H+4kuUHUllDzey+RPHYHD9X7
U6n1PdCH9F15a3IXc8tDjlDdOMNIKJixYuq1UyNZMU6NFwl00+TZf9JF8A2US65b
x/41W98ilL6nNBAsoDVmCLtPNWAqQ3lajaZELGfcqRQ9ZGKcAYOaLFXHv2YHf2XC
qIDMf+slBGSQ66UoATnYV2gAopNlWbZ7n0vO6tE2KyvhHZ1m399aBX1+k8la/0JI
69r+Tz7ZHUSFtmlmyByi5IAB87myy2WQHyAPwj+4vwJkDGPcl0TrupzbG7+T05Y=
=42ti
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
- ARM: GICv3 ITS emulation and various fixes. Removal of the
old VGIC implementation.
- s390: support for trapping software breakpoints, nested
virtualization (vSIE), the STHYI opcode, initial extensions
for CPU model support.
- MIPS: support for MIPS64 hosts (32-bit guests only) and lots
of cleanups, preliminary to this and the upcoming support for
hardware virtualization extensions.
- x86: support for execute-only mappings in nested EPT; reduced
vmexit latency for TSC deadline timer (by about 30%) on Intel
hosts; support for more than 255 vCPUs.
- PPC: bugfixes.
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (302 commits)
KVM: PPC: Introduce KVM_CAP_PPC_HTM
MIPS: Select HAVE_KVM for MIPS64_R{2,6}
MIPS: KVM: Reset CP0_PageMask during host TLB flush
MIPS: KVM: Fix ptr->int cast via KVM_GUEST_KSEGX()
MIPS: KVM: Sign extend MFC0/RDHWR results
MIPS: KVM: Fix 64-bit big endian dynamic translation
MIPS: KVM: Fail if ebase doesn't fit in CP0_EBase
MIPS: KVM: Use 64-bit CP0_EBase when appropriate
MIPS: KVM: Set CP0_Status.KX on MIPS64
MIPS: KVM: Make entry code MIPS64 friendly
MIPS: KVM: Use kmap instead of CKSEG0ADDR()
MIPS: KVM: Use virt_to_phys() to get commpage PFN
MIPS: Fix definition of KSEGX() for 64-bit
KVM: VMX: Add VMCS to CPU's loaded VMCSs before VMPTRLD
kvm: x86: nVMX: maintain internal copy of current VMCS
KVM: PPC: Book3S HV: Save/restore TM state in H_CEDE
KVM: PPC: Book3S HV: Pull out TM state save/restore into separate procedures
KVM: arm64: vgic-its: Simplify MAPI error handling
KVM: arm64: vgic-its: Make vgic_its_cmd_handle_mapi similar to other handlers
KVM: arm64: vgic-its: Turn device_id validation into generic ID validation
...
Kexec needs to know the addresses of all VMCSs that are active on
each CPU, so that it can flush them from the VMCS caches. It is
safe to record superfluous addresses that are not associated with
an active VMCS, but it is not safe to omit an address associated
with an active VMCS.
After a call to vmcs_load, the VMCS that was loaded is active on
the CPU. The VMCS should be added to the CPU's list of active
VMCSs before it is loaded.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
KVM maintains L1's current VMCS in guest memory, at the guest physical
page identified by the argument to VMPTRLD. This makes hairy
time-of-check to time-of-use bugs possible,as VCPUs can be writing
the the VMCS page in memory while KVM is emulating VMLAUNCH and
VMRESUME.
The spec documents that writing to the VMCS page while it is loaded is
"undefined". Therefore it is reasonable to load the entire VMCS into
an internal cache during VMPTRLD and ignore writes to the VMCS page
-- the guest should be using VMREAD and VMWRITE to access the current
VMCS.
To adhere to the spec, KVM should flush the current VMCS during VMPTRLD,
and the target VMCS during VMCLEAR (as given by the operand to VMCLEAR).
Since this implementation of VMCS caching only maintains the the current
VMCS, VMCLEAR will only do a flush if the operand to VMCLEAR is the
current VMCS pointer.
KVM will also flush during VMXOFF, which is not mandated by the spec,
but also not in conflict with the spec.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
1/ Replace pcommit with ADR / directed-flushing:
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement either
ADR, or provide one or more flush addresses per nvdimm. ADR
(Asynchronous DRAM Refresh) flushes data in posted write buffers to the
memory controller on a power-fail event. Flush addresses are defined in
ACPI 6.x as an NVDIMM Firmware Interface Table (NFIT) sub-structure:
"Flush Hint Address Structure". A flush hint is an mmio address that
when written and fenced assures that all previous posted writes
targeting a given dimm have been flushed to media.
2/ On-demand ARS (address range scrub):
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the media
to refresh the bad block list, userspace can also request a re-scrub at
any time.
3/ Support for the Microsoft DSM (device specific method) command format.
4/ Support for EDK2/OVMF virtual disk device memory ranges.
5/ Various fixes and cleanups across the subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXmXBsAAoJEB7SkWpmfYgCEwwP/1IOt9ocP+iHLMDH9KE7VaTZ
NmUDR+Zy6g5cRQM7SgcuU5BXUcx+OsSrSrUTVF1cW994o9Gbz1mFotkv0ZAsPcYY
ZVRQxo2oqHrssyOcg+PsgKWiXn68rJOCgmpEyzaJywl5qTMst7pzsT1s1f7rSh6h
trCf4VaJJwxZR8fARGtlHUnnhPe2Orp99EZRKEWprAsIv2kPuWpPHSjRjuEgN1JG
KW8AYwWqFTtiLRUk86I4KBB0wcDrfctsjgN9Ogd6+aHyQBRnVSr2U+vDCFkC8KLu
qiDCpYp+yyxBjclnljz7tRRT3GtzfCUWd4v2KVWqgg2IaobUc0Lbukp/rmikUXQP
WLikT2OCQ994eFK5OX3Q3cIU/4j459TQnof8q14yVSpjAKrNUXVSR5puN7Hxa+V7
41wKrAsnsyY1oq+Yd/rMR8VfH7PHx3bFkrmRCGZCufLX1UQm4aYj+sWagDKiV3yA
DiudghbOnhfurfGsnXUVw7y7GKs+gNWNBmB6ndAD6ZEHmKoGUhAEbJDLCc3DnANl
b/2mv1MIdIcC1DlCmnbbcn6fv6bICe/r8poK3VrCK3UgOq/EOvKIWl7giP+k1JuC
6DdVYhlNYIVFXUNSLFAwz8OkLu8byx7WDm36iEqrKHtPw+8qa/2bWVgOU6OBgpjV
cN3edFVIdxvZeMgM5Ubq
=xCBG
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
- Replace pcommit with ADR / directed-flushing.
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement
either ADR, or provide one or more flush addresses per nvdimm.
ADR (Asynchronous DRAM Refresh) flushes data in posted write buffers
to the memory controller on a power-fail event.
Flush addresses are defined in ACPI 6.x as an NVDIMM Firmware
Interface Table (NFIT) sub-structure: "Flush Hint Address Structure".
A flush hint is an mmio address that when written and fenced assures
that all previous posted writes targeting a given dimm have been
flushed to media.
- On-demand ARS (address range scrub).
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the
media to refresh the bad block list, userspace can also request a
re-scrub at any time.
- Support for the Microsoft DSM (device specific method) command
format.
- Support for EDK2/OVMF virtual disk device memory ranges.
- Various fixes and cleanups across the subsystem.
* tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (41 commits)
libnvdimm-btt: Delete an unnecessary check before the function call "__nd_device_register"
nfit: do an ARS scrub on hitting a latent media error
nfit: move to nfit/ sub-directory
nfit, libnvdimm: allow an ARS scrub to be triggered on demand
libnvdimm: register nvdimm_bus devices with an nd_bus driver
pmem: clarify a debug print in pmem_clear_poison
x86/insn: remove pcommit
Revert "KVM: x86: add pcommit support"
nfit, tools/testing/nvdimm/: unify shutdown paths
libnvdimm: move ->module to struct nvdimm_bus_descriptor
nfit: cleanup acpi_nfit_init calling convention
nfit: fix _FIT evaluation memory leak + use after free
tools/testing/nvdimm: add manufacturing_{date|location} dimm properties
tools/testing/nvdimm: add virtual ramdisk range
acpi, nfit: treat virtual ramdisk SPA as pmem region
pmem: kill __pmem address space
pmem: kill wmb_pmem()
libnvdimm, pmem: use nvdimm_flush() for namespace I/O writes
fs/dax: remove wmb_pmem()
libnvdimm, pmem: flush posted-write queues on shutdown
...
This reverts commit 8b3e34e46a.
Given the deprecation of the pcommit instruction, the relevant VMX
features and CPUID bits are not going to be rolled into the SDM. Remove
their usage from KVM.
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
With PML enabled, guest will shut down if a PML full VMEXIT occurs during
event delivery. According to Intel SDM 27.2.3, PML full VMEXIT can occur when
event is being delivered through IDT, so KVM should not exit to user space
with error. Instead, it should let EXIT_REASON_PML_FULL go through and the
event will be re-injected on the next VMENTRY.
Signed-off-by: Lei Cao <lei.cao@stratus.com>
Cc: stable@vger.kernel.org
Fixes: 843e433057 ("KVM: VMX: Add PML support in VMX")
[Shortened the summary and Cc'd stable.]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
When freeing the nested resources of a vcpu, there is an assumption that
the vcpu's vmcs01 is the current VMCS on the CPU that executes
nested_release_vmcs12(). If this assumption is violated, the vcpu's
vmcs01 may be made active on multiple CPUs at the same time, in
violation of Intel's specification. Moreover, since the vcpu's vmcs01 is
not VMCLEARed on every CPU on which it is active, it can linger in a
CPU's VMCS cache after it has been freed and potentially
repurposed. Subsequent eviction from the CPU's VMCS cache on a capacity
miss can result in memory corruption.
It is not sufficient for vmx_free_vcpu() to call vmx_load_vmcs01(). If
the vcpu in question was last loaded on a different CPU, it must be
migrated to the current CPU before calling vmx_load_vmcs01().
Signed-off-by: Jim Mattson <jmattson@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Between loading the new VMCS and enabling PML, the CPU was unpinned.
If the vCPU thread were migrated to another CPU in the interim (e.g.,
due to preemption or sleeping alloc_page), then the VMWRITEs to enable
PML would target the wrong VMCS -- or no VMCS at all:
[ 2087.266950] vmwrite error: reg 200e value 3fe1d52000 (err -506126336)
[ 2087.267062] vmwrite error: reg 812 value 1ff (err 511)
[ 2087.267125] vmwrite error: reg 401e value 12229c00 (err 304258048)
This patch ensures that the VMCS remains current while enabling PML by
doing the VMWRITEs while the CPU is pinned. Allocation of the PML buffer
is hoisted out of the critical section.
Signed-off-by: Peter Feiner <pfeiner@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM_CAP_X2APIC_API is a capability for features related to x2APIC
enablement. KVM_X2APIC_API_32BIT_FORMAT feature can be enabled to
extend APIC ID in get/set ioctl and MSI addresses to 32 bits.
Both are needed to support x2APIC.
The feature has to be enableable and disabled by default, because
get/set ioctl shifted and truncated APIC ID to 8 bits by using a
non-standard protocol inspired by xAPIC and the change is not
backward-compatible.
Changes to MSI addresses follow the format used by interrupt remapping
unit. The upper address word, that used to be 0, contains upper 24 bits
of the LAPIC address in its upper 24 bits. Lower 8 bits are reserved as
0. Using the upper address word is not backward-compatible either as we
didn't check that userspace zeroed the word. Reserved bits are still
not explicitly checked, but non-zero data will affect LAPIC addresses,
which will cause a bug.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The register is in hardware-compatible format now, so there is not need
to intercept.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MMU now knows about execute only mappings, so
advertise the feature to L1 hypervisors
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To support execute only mappings on behalf of L1 hypervisors,
reuse ACC_USER_MASK to signify if the L1 hypervisor has the R bit
set.
For the nested EPT case, we assumed that the U bit was always set
since there was no equivalent in EPT page tables. Strictly
speaking, this was not necessary because handle_ept_violation
never set PFERR_USER_MASK in the error code (uf=0 in the
parlance of update_permission_bitmask). We now have to set
both U and UF correctly, respectively in FNAME(gpte_access)
and in handle_ept_violation.
Also in handle_ept_violation bit 3 of the exit qualification is
not enough to detect a present PTE; all three bits 3-5 have to
be checked.
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To support execute only mappings on behalf of L1
hypervisors, we need to teach set_spte() to honor all three of
L1's XWR bits. As a start, add a new variable "shadow_present_mask"
that will be set for non-EPT shadow paging and clear for EPT.
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is no reason to read the entry/exit control fields of the
VMCS and immediately write back the same value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because the vmcs12 preemption timer is emulated through a separate hrtimer,
we can keep on using the preemption timer in the vmcs02 to emulare L1's
TSC deadline timer.
However, the corresponding bit in the pin-based execution control field
must be kept consistent between vmcs01 and vmcs02. On vmentry we copy
it into the vmcs02; on vmexit the preemption timer must be disabled in
the vmcs01 if a preemption timer vmexit happened while in guest mode.
The preemption timer value in the vmcs02 is set by vmx_vcpu_run, so it
need not be considered in prepare_vmcs02.
Cc: Yunhong Jiang <yunhong.jiang@intel.com>
Cc: Haozhong Zhang <haozhong.zhang@intel.com>
Tested-by: Wanpeng Li <kernellwp@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The preemption timer for nested VMX is emulated by hrtimer which is started on L2
entry, stopped on L2 exit and evaluated via the check_nested_events hook. However,
nested_vmx_exit_handled is always returning true for preemption timer vmexit. Then,
the L1 preemption timer vmexit is captured and be treated as a L2 preemption
timer vmexit, causing NULL pointer dereferences or worse in the L1 guest's
vmexit handler:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [< (null)>] (null)
PGD 0
Oops: 0010 [#1] SMP
Call Trace:
? kvm_lapic_expired_hv_timer+0x47/0x90 [kvm]
handle_preemption_timer+0xe/0x20 [kvm_intel]
vmx_handle_exit+0x169/0x15a0 [kvm_intel]
? kvm_arch_vcpu_ioctl_run+0xd5d/0x19d0 [kvm]
kvm_arch_vcpu_ioctl_run+0xdee/0x19d0 [kvm]
? kvm_arch_vcpu_ioctl_run+0xd5d/0x19d0 [kvm]
? vcpu_load+0x1c/0x60 [kvm]
? kvm_arch_vcpu_load+0x57/0x260 [kvm]
kvm_vcpu_ioctl+0x2d3/0x7c0 [kvm]
do_vfs_ioctl+0x96/0x6a0
? __fget_light+0x2a/0x90
SyS_ioctl+0x79/0x90
do_syscall_64+0x68/0x180
entry_SYSCALL64_slow_path+0x25/0x25
Code: Bad RIP value.
RIP [< (null)>] (null)
RSP <ffff8800b5263c48>
CR2: 0000000000000000
---[ end trace 9c70c48b1a2bc66e ]---
This can be reproduced readily by preemption timer enabled on L0 and disabled
on L1.
Return false since preemption timer vmexits must never be reflected to L2.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Yunhong Jiang <yunhong.jiang@intel.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Simplify cpu_has_vmx_preemption_timer. This is consistent with the
rest of setup_vmcs_config and preparatory for the next patch.
Tested-by: Wanpeng Li <kernellwp@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use ARRAY_SIZE instead of dividing sizeof array with sizeof an element
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the TSC deadline timer is programmed really close to the deadline or
even in the past, the computation in vmx_set_hv_timer can underflow and
cause delta_tsc to be set to a huge value. This generally results
in vmx_set_hv_timer returning -ERANGE, but we can fix it by limiting
delta_tsc to be positive or zero.
Reported-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This gains a few clock cycles per vmexit. On Intel there is no need
anymore to enable the interrupts in vmx_handle_external_intr, since
we are using the "acknowledge interrupt on exit" feature. AMD
needs to do that, and must be careful to avoid the interrupt shadow.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I couldn't get Xen to boot a L2 HVM when it was nested under KVM - it was
getting a GP(0) on a rather unspecial vmread from Xen:
(XEN) ----[ Xen-4.7.0-rc x86_64 debug=n Not tainted ]----
(XEN) CPU: 1
(XEN) RIP: e008:[<ffff82d0801e629e>] vmx_get_segment_register+0x14e/0x450
(XEN) RFLAGS: 0000000000010202 CONTEXT: hypervisor (d1v0)
(XEN) rax: ffff82d0801e6288 rbx: ffff83003ffbfb7c rcx: fffffffffffab928
(XEN) rdx: 0000000000000000 rsi: 0000000000000000 rdi: ffff83000bdd0000
(XEN) rbp: ffff83000bdd0000 rsp: ffff83003ffbfab0 r8: ffff830038813910
(XEN) r9: ffff83003faf3958 r10: 0000000a3b9f7640 r11: ffff83003f82d418
(XEN) r12: 0000000000000000 r13: ffff83003ffbffff r14: 0000000000004802
(XEN) r15: 0000000000000008 cr0: 0000000080050033 cr4: 00000000001526e0
(XEN) cr3: 000000003fc79000 cr2: 0000000000000000
(XEN) ds: 0000 es: 0000 fs: 0000 gs: 0000 ss: 0000 cs: e008
(XEN) Xen code around <ffff82d0801e629e> (vmx_get_segment_register+0x14e/0x450):
(XEN) 00 00 41 be 02 48 00 00 <44> 0f 78 74 24 08 0f 86 38 56 00 00 b8 08 68 00
(XEN) Xen stack trace from rsp=ffff83003ffbfab0:
...
(XEN) Xen call trace:
(XEN) [<ffff82d0801e629e>] vmx_get_segment_register+0x14e/0x450
(XEN) [<ffff82d0801f3695>] get_page_from_gfn_p2m+0x165/0x300
(XEN) [<ffff82d0801bfe32>] hvmemul_get_seg_reg+0x52/0x60
(XEN) [<ffff82d0801bfe93>] hvm_emulate_prepare+0x53/0x70
(XEN) [<ffff82d0801ccacb>] handle_mmio+0x2b/0xd0
(XEN) [<ffff82d0801be591>] emulate.c#_hvm_emulate_one+0x111/0x2c0
(XEN) [<ffff82d0801cd6a4>] handle_hvm_io_completion+0x274/0x2a0
(XEN) [<ffff82d0801f334a>] __get_gfn_type_access+0xfa/0x270
(XEN) [<ffff82d08012f3bb>] timer.c#add_entry+0x4b/0xb0
(XEN) [<ffff82d08012f80c>] timer.c#remove_entry+0x7c/0x90
(XEN) [<ffff82d0801c8433>] hvm_do_resume+0x23/0x140
(XEN) [<ffff82d0801e4fe7>] vmx_do_resume+0xa7/0x140
(XEN) [<ffff82d080164aeb>] context_switch+0x13b/0xe40
(XEN) [<ffff82d080128e6e>] schedule.c#schedule+0x22e/0x570
(XEN) [<ffff82d08012c0cc>] softirq.c#__do_softirq+0x5c/0x90
(XEN) [<ffff82d0801602c5>] domain.c#idle_loop+0x25/0x50
(XEN)
(XEN)
(XEN) ****************************************
(XEN) Panic on CPU 1:
(XEN) GENERAL PROTECTION FAULT
(XEN) [error_code=0000]
(XEN) ****************************************
Tracing my host KVM showed it was the one injecting the GP(0) when
emulating the VMREAD and checking the destination segment permissions in
get_vmx_mem_address():
3) | vmx_handle_exit() {
3) | handle_vmread() {
3) | nested_vmx_check_permission() {
3) | vmx_get_segment() {
3) 0.074 us | vmx_read_guest_seg_base();
3) 0.065 us | vmx_read_guest_seg_selector();
3) 0.066 us | vmx_read_guest_seg_ar();
3) 1.636 us | }
3) 0.058 us | vmx_get_rflags();
3) 0.062 us | vmx_read_guest_seg_ar();
3) 3.469 us | }
3) | vmx_get_cs_db_l_bits() {
3) 0.058 us | vmx_read_guest_seg_ar();
3) 0.662 us | }
3) | get_vmx_mem_address() {
3) 0.068 us | vmx_cache_reg();
3) | vmx_get_segment() {
3) 0.074 us | vmx_read_guest_seg_base();
3) 0.068 us | vmx_read_guest_seg_selector();
3) 0.071 us | vmx_read_guest_seg_ar();
3) 1.756 us | }
3) | kvm_queue_exception_e() {
3) 0.066 us | kvm_multiple_exception();
3) 0.684 us | }
3) 4.085 us | }
3) 9.833 us | }
3) + 10.366 us | }
Cross-checking the KVM/VMX VMREAD emulation code with the Intel Software
Developper Manual Volume 3C - "VMREAD - Read Field from Virtual-Machine
Control Structure", I found that we're enforcing that the destination
operand is NOT located in a read-only data segment or any code segment when
the L1 is in long mode - BUT that check should only happen when it is in
protected mode.
Shuffling the code a bit to make our emulation follow the specification
allows me to boot a Xen dom0 in a nested KVM and start HVM L2 guests
without problems.
Fixes: f9eb4af67c ("KVM: nVMX: VMX instructions: add checks for #GP/#SS exceptions")
Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Eugene Korenevsky <ekorenevsky@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On Intel platforms, this patch adds LMCE to KVM MCE supported
capabilities and handles guest access to LMCE related MSRs.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
[Haozhong: macro KVM_MCE_CAP_SUPPORTED => variable kvm_mce_cap_supported
Only enable LMCE on Intel platform
Check MSR_IA32_FEATURE_CONTROL when handling guest
access to MSR_IA32_MCG_EXT_CTL]
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM currently does not check the value written to guest
MSR_IA32_FEATURE_CONTROL, though bits corresponding to disabled features
may be set. This patch makes KVM to validate individual bits written to
guest MSR_IA32_FEATURE_CONTROL according to enabled features.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
msr_ia32_feature_control will be used for LMCE and not depend only on
nested anymore, so move it from struct nested_vmx to struct vcpu_vmx.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hook the VMX preemption timer to the "hv timer" functionality added
by the previous patch. This includes: checking if the feature is
supported, if the feature is broken on the CPU, the hooks to
setup/clean the VMX preemption timer, arming the timer on vmentry
and handling the vmexit.
A module parameter states if the VMX preemption timer should be
utilized.
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>
[Move hv_deadline_tsc to struct vcpu_vmx, use -1 as the "unset" value.
Put all VMX bits here. Enable it by default #yolo. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Prepare to switch from preemption timer to hrtimer in the
vmx_pre/post_block. Current functions are only for posted interrupt,
rename them accordingly.
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VT-d posted interrupt is relying on the CPU side's posted interrupt.
Need to check whether VCPU's APICv is active before enabing VT-d
posted interrupt.
Fixes: d62caabb41
Cc: stable@vger.kernel.org
Signed-off-by: Yang Zhang <yang.zhang.wz@gmail.com>
Signed-off-by: Shengge Ding <shengge.dsg@alibaba-inc.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(kvm_stat had nothing to do with QEMU in the first place -- the tool
only interprets debugfs)
- expose per-vm statistics in debugfs and support them in kvm_stat
(KVM always collected per-vm statistics, but they were summarised into
global statistics)
x86:
- fix dynamic APICv (VMX was improperly configured and a guest could
access host's APIC MSRs, CVE-2016-4440)
- minor fixes
ARM changes from Christoffer Dall:
"This set of changes include the new vgic, which is a reimplementation
of our horribly broken legacy vgic implementation. The two
implementations will live side-by-side (with the new being the
configured default) for one kernel release and then we'll remove the
legacy one.
Also fixes a non-critical issue with virtual abort injection to
guests."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXRz0KAAoJEED/6hsPKofosiMIAIHmRI+9I6VMNmQe5vrZKz9/
vt89QGxDJrFQwhEuZovenLEDaY6rMIJNguyvIbPhNuXNHIIPWbe6cO6OPwByqkdo
WI/IIqcAJN/Bpwt4/Y2977A5RwDOwWLkaDs0LrZCEKPCgeh9GWQf+EfyxkDJClhG
uIgbSAU+t+7b05K3c6NbiQT/qCzDTCdl6In6PI/DFSRRkXDaTcopjjp1PmMUSSsR
AM8LGhEzMer+hGKOH7H5TIbN+HFzAPjBuDGcoZt0/w9IpmmS5OMd3ZrZ320cohz8
zZQooRcFrT0ulAe+TilckmRMJdMZ69fyw3nzfqgAKEx+3PaqjKSY/tiEgqqDJHY=
=EEBK
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull second batch of KVM updates from Radim Krčmář:
"General:
- move kvm_stat tool from QEMU repo into tools/kvm/kvm_stat (kvm_stat
had nothing to do with QEMU in the first place -- the tool only
interprets debugfs)
- expose per-vm statistics in debugfs and support them in kvm_stat
(KVM always collected per-vm statistics, but they were summarised
into global statistics)
x86:
- fix dynamic APICv (VMX was improperly configured and a guest could
access host's APIC MSRs, CVE-2016-4440)
- minor fixes
ARM changes from Christoffer Dall:
- new vgic reimplementation of our horribly broken legacy vgic
implementation. The two implementations will live side-by-side
(with the new being the configured default) for one kernel release
and then we'll remove the legacy one.
- fix for a non-critical issue with virtual abort injection to guests"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (70 commits)
tools: kvm_stat: Add comments
tools: kvm_stat: Introduce pid monitoring
KVM: Create debugfs dir and stat files for each VM
MAINTAINERS: Add kvm tools
tools: kvm_stat: Powerpc related fixes
tools: Add kvm_stat man page
tools: Add kvm_stat vm monitor script
kvm:vmx: more complete state update on APICv on/off
KVM: SVM: Add more SVM_EXIT_REASONS
KVM: Unify traced vector format
svm: bitwise vs logical op typo
KVM: arm/arm64: vgic-new: Synchronize changes to active state
KVM: arm/arm64: vgic-new: enable build
KVM: arm/arm64: vgic-new: implement mapped IRQ handling
KVM: arm/arm64: vgic-new: Wire up irqfd injection
KVM: arm/arm64: vgic-new: Add vgic_v2/v3_enable
KVM: arm/arm64: vgic-new: vgic_init: implement map_resources
KVM: arm/arm64: vgic-new: vgic_init: implement vgic_init
KVM: arm/arm64: vgic-new: vgic_init: implement vgic_create
KVM: arm/arm64: vgic-new: vgic_init: implement kvm_vgic_hyp_init
...
The function to update APICv on/off state (in particular, to deactivate
it when enabling Hyper-V SynIC) is incomplete: it doesn't adjust
APICv-related fields among secondary processor-based VM-execution
controls. As a result, Windows 2012 guests get stuck when SynIC-based
auto-EOI interrupt intersected with e.g. an IPI in the guest.
In addition, the MSR intercept bitmap isn't updated every time "virtualize
x2APIC mode" is toggled. This path can only be triggered by a malicious
guest, because Windows didn't use x2APIC but rather their own synthetic
APIC access MSRs; however a guest running in a SynIC-enabled VM could
switch to x2APIC and thus obtain direct access to host APIC MSRs
(CVE-2016-4440).
The patch fixes those omissions.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Reported-by: Steve Rutherford <srutherford@google.com>
Reported-by: Yang Zhang <yang.zhang.wz@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- x86: miscellaneous fixes, AVIC support (local APIC virtualization,
AMD version)
- s390: polling for interrupts after a VCPU goes to halted state is
now enabled for s390; use hardware provided information about facility
bits that do not need any hypervisor activity, and other fixes for
cpu models and facilities; improve perf output; floating interrupt
controller improvements.
- MIPS: miscellaneous fixes
- PPC: bugfixes only
- ARM: 16K page size support, generic firmware probing layer for
timer and GIC
Christoffer Dall (KVM-ARM maintainer) says:
"There are a few changes in this pull request touching things outside
KVM, but they should all carry the necessary acks and it made the
merge process much easier to do it this way."
though actually the irqchip maintainers' acks didn't make it into the
patches. Marc Zyngier, who is both irqchip and KVM-ARM maintainer,
later acked at http://mid.gmane.org/573351D1.4060303@arm.com
"more formally and for documentation purposes".
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXPJjyAAoJEL/70l94x66DhioH/j4fwQ0FmfPSM9PArzaFHQdx
LNE3tU4+bobbsy1BJr4DiAaOUQn3DAgwUvGLWXdeLiOXtoWXBiFHKaxlqEsCA6iQ
xcTH1TgfxsVoqGQ6bT9X/2GCx70heYpcWG3f+zqBy7ZfFmQykLAC/HwOr52VQL8f
hUFi3YmTHcnorp0n5Xg+9r3+RBS4D/kTbtdn6+KCLnPJ0RcgNkI3/NcafTemoofw
Tkv8+YYFNvKV13qlIfVqxMa0GwWI3pP6YaNKhaS5XO8Pu16HuuF1JthJsUBDzwBa
RInp8R9MoXgsBYhLpz3jc9vWG7G9yDl5LehsD9KOUGOaFYJ7sQN+QZOusa6jFgA=
=llO5
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Small release overall.
x86:
- miscellaneous fixes
- AVIC support (local APIC virtualization, AMD version)
s390:
- polling for interrupts after a VCPU goes to halted state is now
enabled for s390
- use hardware provided information about facility bits that do not
need any hypervisor activity, and other fixes for cpu models and
facilities
- improve perf output
- floating interrupt controller improvements.
MIPS:
- miscellaneous fixes
PPC:
- bugfixes only
ARM:
- 16K page size support
- generic firmware probing layer for timer and GIC
Christoffer Dall (KVM-ARM maintainer) says:
"There are a few changes in this pull request touching things
outside KVM, but they should all carry the necessary acks and it
made the merge process much easier to do it this way."
though actually the irqchip maintainers' acks didn't make it into the
patches. Marc Zyngier, who is both irqchip and KVM-ARM maintainer,
later acked at http://mid.gmane.org/573351D1.4060303@arm.com ('more
formally and for documentation purposes')"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (82 commits)
KVM: MTRR: remove MSR 0x2f8
KVM: x86: make hwapic_isr_update and hwapic_irr_update look the same
svm: Manage vcpu load/unload when enable AVIC
svm: Do not intercept CR8 when enable AVIC
svm: Do not expose x2APIC when enable AVIC
KVM: x86: Introducing kvm_x86_ops.apicv_post_state_restore
svm: Add VMEXIT handlers for AVIC
svm: Add interrupt injection via AVIC
KVM: x86: Detect and Initialize AVIC support
svm: Introduce new AVIC VMCB registers
KVM: split kvm_vcpu_wake_up from kvm_vcpu_kick
KVM: x86: Introducing kvm_x86_ops VCPU blocking/unblocking hooks
KVM: x86: Introducing kvm_x86_ops VM init/destroy hooks
KVM: x86: Rename kvm_apic_get_reg to kvm_lapic_get_reg
KVM: x86: Misc LAPIC changes to expose helper functions
KVM: shrink halt polling even more for invalid wakeups
KVM: s390: set halt polling to 80 microseconds
KVM: halt_polling: provide a way to qualify wakeups during poll
KVM: PPC: Book3S HV: Re-enable XICS fast path for irqfd-generated interrupts
kvm: Conditionally register IRQ bypass consumer
...
Neither APICv nor AVIC actually need the first argument of
hwapic_isr_update, but the vCPU makes more sense than passing the
pointer to the whole virtual machine! In fact in the APICv case it's
just happening that the vCPU is used implicitly, through the loaded VMCS.
The second argument instead is named differently, make it consistent.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit d28bc9dd25 reversed the order of two lines which initialize cr0,
allowing the current (old) cr0 value to mess up vcpu initialization.
This was observed in the checks for cr0 X86_CR0_WP bit in the context of
kvm_mmu_reset_context(). Besides, setting vcpu->arch.cr0 after vmx_set_cr0()
is completely redundant. Change the order back to ensure proper vcpu
initialization.
The combination of booting with ovmf firmware when guest vcpus > 1 and kvm's
ept=N option being set results in a VM-entry failure. This patch fixes that.
Fixes: d28bc9dd25 ("KVM: x86: INIT and reset sequences are different")
Cc: stable@vger.kernel.org
Signed-off-by: Bruce Rogers <brogers@suse.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Some versions of Intel PT do not support tracing across VMXON, more
specifically, VMXON will clear TraceEn control bit and any attempt to
set it before VMXOFF will throw a #GP, which in the current state of
things will crash the kernel. Namely:
$ perf record -e intel_pt// kvm -nographic
on such a machine will kill it.
To avoid this, notify the intel_pt driver before VMXON and after
VMXOFF so that it knows when not to enable itself.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: hpa@zytor.com
Link: http://lkml.kernel.org/r/87oa9dwrfk.fsf@ashishki-desk.ger.corp.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Protection keys define a new 4-bit protection key field (PKEY) in bits
62:59 of leaf entries of the page tables, the PKEY is an index to PKRU
register(16 domains), every domain has 2 bits(write disable bit, access
disable bit).
Static logic has been produced in update_pkru_bitmask, dynamic logic need
read pkey from page table entries, get pkru value, and deduce the correct
result.
[ Huaitong: Xiao helps to modify many sections. ]
Signed-off-by: Huaitong Han <huaitong.han@intel.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently XSAVE state of host is not restored after VM-exit and PKRU
is managed by XSAVE so the PKRU from guest is still controlling the
memory access even if the CPU is running the code of host. This is
not safe as KVM needs to access the memory of userspace (e,g QEMU) to
do some emulation.
So we save/restore PKRU when guest/host switches.
Signed-off-by: Huaitong Han <huaitong.han@intel.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pkeys is disabled if CPU is in non-paging mode in hardware. However KVM
always uses paging mode to emulate guest non-paging, mode with TDP. To
emulate this behavior, pkeys needs to be manually disabled when guest
switches to non-paging mode.
Signed-off-by: Huaitong Han <huaitong.han@intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Old KVM guests invoke single-context invvpid without actually checking
whether it is supported. This was fixed by commit 518c8ae ("KVM: VMX:
Make sure single type invvpid is supported before issuing invvpid
instruction", 2010-08-01) and the patch after, but pre-2.6.36
kernels lack it including RHEL 6.
Reported-by: jmontleo@redhat.com
Tested-by: jmontleo@redhat.com
Cc: stable@vger.kernel.org
Fixes: 99b83ac893
Reviewed-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A guest executing an invalid invvpid instruction would hang
because the instruction pointer was not updated.
Reported-by: jmontleo@redhat.com
Tested-by: jmontleo@redhat.com
Cc: stable@vger.kernel.org
Fixes: 99b83ac893
Reviewed-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A guest executing an invalid invept instruction would hang
because the instruction pointer was not updated.
Cc: stable@vger.kernel.org
Fixes: bfd0a56b90
Reviewed-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull 'objtool' stack frame validation from Ingo Molnar:
"This tree adds a new kernel build-time object file validation feature
(ONFIG_STACK_VALIDATION=y): kernel stack frame correctness validation.
It was written by and is maintained by Josh Poimboeuf.
The motivation: there's a category of hard to find kernel bugs, most
of them in assembly code (but also occasionally in C code), that
degrades the quality of kernel stack dumps/backtraces. These bugs are
hard to detect at the source code level. Such bugs result in
incorrect/incomplete backtraces most of time - but can also in some
rare cases result in crashes or other undefined behavior.
The build time correctness checking is done via the new 'objtool'
user-space utility that was written for this purpose and which is
hosted in the kernel repository in tools/objtool/. The tool's (very
simple) UI and source code design is shaped after Git and perf and
shares quite a bit of infrastructure with tools/perf (which tooling
infrastructure sharing effort got merged via perf and is already
upstream). Objtool follows the well-known kernel coding style.
Objtool does not try to check .c or .S files, it instead analyzes the
resulting .o generated machine code from first principles: it decodes
the instruction stream and interprets it. (Right now objtool supports
the x86-64 architecture.)
From tools/objtool/Documentation/stack-validation.txt:
"The kernel CONFIG_STACK_VALIDATION option enables a host tool named
objtool which runs at compile time. It has a "check" subcommand
which analyzes every .o file and ensures the validity of its stack
metadata. It enforces a set of rules on asm code and C inline
assembly code so that stack traces can be reliable.
Currently it only checks frame pointer usage, but there are plans to
add CFI validation for C files and CFI generation for asm files.
For each function, it recursively follows all possible code paths
and validates the correct frame pointer state at each instruction.
It also follows code paths involving special sections, like
.altinstructions, __jump_table, and __ex_table, which can add
alternative execution paths to a given instruction (or set of
instructions). Similarly, it knows how to follow switch statements,
for which gcc sometimes uses jump tables."
When this new kernel option is enabled (it's disabled by default), the
tool, if it finds any suspicious assembly code pattern, outputs
warnings in compiler warning format:
warning: objtool: rtlwifi_rate_mapping()+0x2e7: frame pointer state mismatch
warning: objtool: cik_tiling_mode_table_init()+0x6ce: call without frame pointer save/setup
warning: objtool:__schedule()+0x3c0: duplicate frame pointer save
warning: objtool:__schedule()+0x3fd: sibling call from callable instruction with changed frame pointer
... so that scripts that pick up compiler warnings will notice them.
All known warnings triggered by the tool are fixed by the tree, most
of the commits in fact prepare the kernel to be warning-free. Most of
them are bugfixes or cleanups that stand on their own, but there are
also some annotations of 'special' stack frames for justified cases
such entries to JIT-ed code (BPF) or really special boot time code.
There are two other long-term motivations behind this tool as well:
- To improve the quality and reliability of kernel stack frames, so
that they can be used for optimized live patching.
- To create independent infrastructure to check the correctness of
CFI stack frames at build time. CFI debuginfo is notoriously
unreliable and we cannot use it in the kernel as-is without extra
checking done both on the kernel side and on the build side.
The quality of kernel stack frames matters to debuggability as well,
so IMO we can merge this without having to consider the live patching
or CFI debuginfo angle"
* 'core-objtool-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (52 commits)
objtool: Only print one warning per function
objtool: Add several performance improvements
tools: Copy hashtable.h into tools directory
objtool: Fix false positive warnings for functions with multiple switch statements
objtool: Rename some variables and functions
objtool: Remove superflous INIT_LIST_HEAD
objtool: Add helper macros for traversing instructions
objtool: Fix false positive warnings related to sibling calls
objtool: Compile with debugging symbols
objtool: Detect infinite recursion
objtool: Prevent infinite recursion in noreturn detection
objtool: Detect and warn if libelf is missing and don't break the build
tools: Support relative directory path for 'O='
objtool: Support CROSS_COMPILE
x86/asm/decoder: Use explicitly signed chars
objtool: Enable stack metadata validation on 64-bit x86
objtool: Add CONFIG_STACK_VALIDATION option
objtool: Add tool to perform compile-time stack metadata validation
x86/kprobes: Mark kretprobe_trampoline() stack frame as non-standard
sched: Always inline context_switch()
...
but lots of architecture-specific changes.
* ARM:
- VHE support so that we can run the kernel at EL2 on ARMv8.1 systems
- PMU support for guests
- 32bit world switch rewritten in C
- various optimizations to the vgic save/restore code.
* PPC:
- enabled KVM-VFIO integration ("VFIO device")
- optimizations to speed up IPIs between vcpus
- in-kernel handling of IOMMU hypercalls
- support for dynamic DMA windows (DDW).
* s390:
- provide the floating point registers via sync regs;
- separated instruction vs. data accesses
- dirty log improvements for huge guests
- bugfixes and documentation improvements.
* x86:
- Hyper-V VMBus hypercall userspace exit
- alternative implementation of lowest-priority interrupts using vector
hashing (for better VT-d posted interrupt support)
- fixed guest debugging with nested virtualizations
- improved interrupt tracking in the in-kernel IOAPIC
- generic infrastructure for tracking writes to guest memory---currently
its only use is to speedup the legacy shadow paging (pre-EPT) case, but
in the future it will be used for virtual GPUs as well
- much cleanup (LAPIC, kvmclock, MMU, PIT), including ubsan fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJW5r3BAAoJEL/70l94x66D2pMH/jTSWWwdTUJMctrDjPVzKzG0
yOzHW5vSLFoFlwEOY2VpslnXzn5TUVmCAfrdmFNmQcSw6hGb3K/xA/ZX/KLwWhyb
oZpr123ycahga+3q/ht/dFUBCCyWeIVMdsLSFwpobEBzPL0pMgc9joLgdUC6UpWX
tmN0LoCAeS7spC4TTiTTpw3gZ/L+aB0B6CXhOMjldb9q/2CsgaGyoVvKA199nk9o
Ngu7ImDt7l/x1VJX4/6E/17VHuwqAdUrrnbqerB/2oJ5ixsZsHMGzxQ3sHCmvyJx
WG5L00ubB1oAJAs9fBg58Y/MdiWX99XqFhdEfxq4foZEiQuCyxygVvq3JwZTxII=
=OUZZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"One of the largest releases for KVM... Hardly any generic
changes, but lots of architecture-specific updates.
ARM:
- VHE support so that we can run the kernel at EL2 on ARMv8.1 systems
- PMU support for guests
- 32bit world switch rewritten in C
- various optimizations to the vgic save/restore code.
PPC:
- enabled KVM-VFIO integration ("VFIO device")
- optimizations to speed up IPIs between vcpus
- in-kernel handling of IOMMU hypercalls
- support for dynamic DMA windows (DDW).
s390:
- provide the floating point registers via sync regs;
- separated instruction vs. data accesses
- dirty log improvements for huge guests
- bugfixes and documentation improvements.
x86:
- Hyper-V VMBus hypercall userspace exit
- alternative implementation of lowest-priority interrupts using
vector hashing (for better VT-d posted interrupt support)
- fixed guest debugging with nested virtualizations
- improved interrupt tracking in the in-kernel IOAPIC
- generic infrastructure for tracking writes to guest
memory - currently its only use is to speedup the legacy shadow
paging (pre-EPT) case, but in the future it will be used for
virtual GPUs as well
- much cleanup (LAPIC, kvmclock, MMU, PIT), including ubsan fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (217 commits)
KVM: x86: remove eager_fpu field of struct kvm_vcpu_arch
KVM: x86: disable MPX if host did not enable MPX XSAVE features
arm64: KVM: vgic-v3: Only wipe LRs on vcpu exit
arm64: KVM: vgic-v3: Reset LRs at boot time
arm64: KVM: vgic-v3: Do not save an LR known to be empty
arm64: KVM: vgic-v3: Save maintenance interrupt state only if required
arm64: KVM: vgic-v3: Avoid accessing ICH registers
KVM: arm/arm64: vgic-v2: Make GICD_SGIR quicker to hit
KVM: arm/arm64: vgic-v2: Only wipe LRs on vcpu exit
KVM: arm/arm64: vgic-v2: Reset LRs at boot time
KVM: arm/arm64: vgic-v2: Do not save an LR known to be empty
KVM: arm/arm64: vgic-v2: Move GICH_ELRSR saving to its own function
KVM: arm/arm64: vgic-v2: Save maintenance interrupt state only if required
KVM: arm/arm64: vgic-v2: Avoid accessing GICH registers
KVM: s390: allocate only one DMA page per VM
KVM: s390: enable STFLE interpretation only if enabled for the guest
KVM: s390: wake up when the VCPU cpu timer expires
KVM: s390: step the VCPU timer while in enabled wait
KVM: s390: protect VCPU cpu timer with a seqcount
KVM: s390: step VCPU cpu timer during kvm_run ioctl
...
Yes, all of these are needed. :) This is admittedly a bit odd, but
kvm-unit-tests access.flat tests this if you run it with "-cpu host"
and of course ept=0.
KVM runs the guest with CR0.WP=1, so it must handle supervisor writes
specially when pte.u=1/pte.w=0/CR0.WP=0. Such writes cause a fault
when U=1 and W=0 in the SPTE, but they must succeed because CR0.WP=0.
When KVM gets the fault, it sets U=0 and W=1 in the shadow PTE and
restarts execution. This will still cause a user write to fault, while
supervisor writes will succeed. User reads will fault spuriously now,
and KVM will then flip U and W again in the SPTE (U=1, W=0). User reads
will be enabled and supervisor writes disabled, going back to the
originary situation where supervisor writes fault spuriously.
When SMEP is in effect, however, U=0 will enable kernel execution of
this page. To avoid this, KVM also sets NX=1 in the shadow PTE together
with U=0. If the guest has not enabled NX, the result is a continuous
stream of page faults due to the NX bit being reserved.
The fix is to force EFER.NX=1 even if the CPU is taking care of the EFER
switch. (All machines with SMEP have the CPU_LOAD_IA32_EFER vm-entry
control, so they do not use user-return notifiers for EFER---if they did,
EFER.NX would be forced to the same value as the host).
There is another bug in the reserved bit check, which I've split to a
separate patch for easier application to stable kernels.
Cc: stable@vger.kernel.org
Cc: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Fixes: f6577a5fa1
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When eager FPU is disabled, KVM will still see the MPX bit in CPUID and
presumably the MPX vmentry and vmexit controls. However, it will not
be able to expose the MPX XSAVE features to the guest, because the guest's
accessible XSAVE features are always a subset of host_xcr0.
In this case, we should disable the MPX CPUID bit, the BNDCFGS MSR,
and the MPX vmentry and vmexit controls for nested virtualization.
It is then unnecessary to enable guest eager FPU if the guest has the
MPX CPUID bit set.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linux guests on Haswell (and also SandyBridge and Broadwell, at least)
would crash if you decided to run a host command that uses PEBS, like
perf record -e 'cpu/mem-stores/pp' -a
This happens because KVM is using VMX MSR switching to disable PEBS, but
SDM [2015-12] 18.4.4.4 Re-configuring PEBS Facilities explains why it
isn't safe:
When software needs to reconfigure PEBS facilities, it should allow a
quiescent period between stopping the prior event counting and setting
up a new PEBS event. The quiescent period is to allow any latent
residual PEBS records to complete its capture at their previously
specified buffer address (provided by IA32_DS_AREA).
There might not be a quiescent period after the MSR switch, so a CPU
ends up using host's MSR_IA32_DS_AREA to access an area in guest's
memory. (Or MSR switching is just buggy on some models.)
The guest can learn something about the host this way:
If the guest doesn't map address pointed by MSR_IA32_DS_AREA, it results
in #PF where we leak host's MSR_IA32_DS_AREA through CR2.
After that, a malicious guest can map and configure memory where
MSR_IA32_DS_AREA is pointing and can therefore get an output from
host's tracing.
This is not a critical leak as the host must initiate with PEBS tracing
and I have not been able to get a record from more than one instruction
before vmentry in vmx_vcpu_run() (that place has most registers already
overwritten with guest's).
We could disable PEBS just few instructions before vmentry, but
disabling it earlier shouldn't affect host tracing too much.
We also don't need to switch MSR_IA32_PEBS_ENABLE on VMENTRY, but that
optimization isn't worth its code, IMO.
(If you are implementing PEBS for guests, be sure to handle the case
where both host and guest enable PEBS, because this patch doesn't.)
Fixes: 26a4f3c08d ("perf/x86: disable PEBS on a guest entry.")
Cc: <stable@vger.kernel.org>
Reported-by: Jiří Olša <jolsa@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
vmx.c writes the TSC_MULTIPLIER field in vmx_vcpu_load, but only when a
vcpu has migrated physical cpus. Record the last value written and
update in vmx_vcpu_load on any change, otherwise a cpu migration must
occur for TSC frequency scaling to take effect.
Cc: stable@vger.kernel.org
Fixes: ff2c3a1803
Signed-off-by: Owen Hofmann <osh@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stacktool generates the following warning:
stacktool: arch/x86/kvm/vmx.o: vmx_handle_external_intr()+0x67: call without frame pointer save/setup
By adding the stackpointer as an output operand, this patch ensures that a
stack frame is created when CONFIG_FRAME_POINTER is enabled for the inline
assmebly statement.
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: gleb@kernel.org
Cc: kvm@vger.kernel.org
Cc: live-patching@vger.kernel.org
Cc: pbonzini@redhat.com
Link: http://lkml.kernel.org/r/1453499078-9330-3-git-send-email-chris.j.arges@canonical.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
To make the intention clearer, use list_last_entry instead of
list_entry.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pass the return code from kvm_emulate_hypercall on to the caller,
in order to allow it to indicate to the userspace that
the hypercall has to be handled there.
Also adjust all the existing code paths to return 1 to make sure the
hypercall isn't passed to the userspace without setting kvm_run
appropriately.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When we take a #DB or #BP vmexit while in guest mode, we first of all
need to check if there is ongoing guest debugging that might be
interested in the event. Currently, we unconditionally leave L2 and
inject the event into L1 if it is intercepting the exceptions. That
breaks things marvelously.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is quite some common code in all these is_<exception>() helpers.
Factor it out before adding even more of them.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add host irq information in trace event, so we can better understand
which irq is in posted mode.
Signed-off-by: Feng Wu <feng.wu@intel.com>
Reviewed-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When the interrupt is not single destination any more, we need
to change back IRTE to remapped mode explicitly.
Signed-off-by: Feng Wu <feng.wu@intel.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To date, we have implemented two I/O usage models for persistent memory,
PMEM (a persistent "ram disk") and DAX (mmap persistent memory into
userspace). This series adds a third, DAX-GUP, that allows DAX mappings
to be the target of direct-i/o. It allows userspace to coordinate
DMA/RDMA from/to persistent memory.
The implementation leverages the ZONE_DEVICE mm-zone that went into
4.3-rc1 (also discussed at kernel summit) to flag pages that are owned
and dynamically mapped by a device driver. The pmem driver, after
mapping a persistent memory range into the system memmap via
devm_memremap_pages(), arranges for DAX to distinguish pfn-only versus
page-backed pmem-pfns via flags in the new pfn_t type.
The DAX code, upon seeing a PFN_DEV+PFN_MAP flagged pfn, flags the
resulting pte(s) inserted into the process page tables with a new
_PAGE_DEVMAP flag. Later, when get_user_pages() is walking ptes it keys
off _PAGE_DEVMAP to pin the device hosting the page range active.
Finally, get_page() and put_page() are modified to take references
against the device driver established page mapping.
Finally, this need for "struct page" for persistent memory requires
memory capacity to store the memmap array. Given the memmap array for a
large pool of persistent may exhaust available DRAM introduce a
mechanism to allocate the memmap from persistent memory. The new
"struct vmem_altmap *" parameter to devm_memremap_pages() enables
arch_add_memory() to use reserved pmem capacity rather than the page
allocator.
This patch (of 18):
The core has developed a need for a "pfn_t" type [1]. Move the existing
pfn_t in KVM to kvm_pfn_t [2].
[1]: https://lists.01.org/pipermail/linux-nvdimm/2015-September/002199.html
[2]: https://lists.01.org/pipermail/linux-nvdimm/2015-September/002218.html
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
support of 248 VCPUs.
* ARM: rewrite of the arm64 world switch in C, support for
16-bit VM identifiers. Performance counter virtualization
missed the boat.
* x86: Support for more Hyper-V features (synthetic interrupt
controller), MMU cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJWlSKwAAoJEL/70l94x66DY0UIAK5vp4zfQoQOJC4KP4Xgxwdu
kpnK2Boz3/74o1b0y5+eJZoUZCsXCVLtmP5uhmMxUYWDgByFG2X8ZDhPFwB5FYLT
2dN+Lr4tsolgIfRdHZtrT6Svp9SDL039bWTdscnbR6l37/j9FRWvpKdhI3orloFD
/i4CSW2dVIq1/9Xctwu/rtcOEesEx4Cad+6YV3/530eVAXFzE908nXfmqJNZTocY
YCGcmrMVCOu0ng5QM4xSzmmYjKMLUcRs+QzZWkVBzdJtTgwZUr09yj7I2dZ1yj/i
cxYrJy6shSwE74XkXsmvG+au3C5u3vX4tnXjBFErnPJ99oqzHatVnFWNRhj4dLQ=
=PIj1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"PPC changes will come next week.
- s390: Support for runtime instrumentation within guests, support of
248 VCPUs.
- ARM: rewrite of the arm64 world switch in C, support for 16-bit VM
identifiers. Performance counter virtualization missed the boat.
- x86: Support for more Hyper-V features (synthetic interrupt
controller), MMU cleanups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (115 commits)
kvm: x86: Fix vmwrite to SECONDARY_VM_EXEC_CONTROL
kvm/x86: Hyper-V SynIC timers tracepoints
kvm/x86: Hyper-V SynIC tracepoints
kvm/x86: Update SynIC timers on guest entry only
kvm/x86: Skip SynIC vector check for QEMU side
kvm/x86: Hyper-V fix SynIC timer disabling condition
kvm/x86: Reorg stimer_expiration() to better control timer restart
kvm/x86: Hyper-V unify stimer_start() and stimer_restart()
kvm/x86: Drop stimer_stop() function
kvm/x86: Hyper-V timers fix incorrect logical operation
KVM: move architecture-dependent requests to arch/
KVM: renumber vcpu->request bits
KVM: document which architecture uses each request bit
KVM: Remove unused KVM_REQ_KICK to save a bit in vcpu->requests
kvm: x86: Check kvm_write_guest return value in kvm_write_wall_clock
KVM: s390: implement the RI support of guest
kvm/s390: drop unpaired smp_mb
kvm: x86: fix comment about {mmu,nested_mmu}.gva_to_gpa
KVM: x86: MMU: Use clear_page() instead of init_shadow_page_table()
arm/arm64: KVM: Detect vGIC presence at runtime
...
vmx_cpuid_tries to update SECONDARY_VM_EXEC_CONTROL in the VMCS, but
it will cause a vmwrite error on older CPUs because the code does not
check for the presence of CPU_BASED_ACTIVATE_SECONDARY_CONTROLS.
This will get rid of the following trace on e.g. Core2 6600:
vmwrite error: reg 401e value 10 (err 12)
Call Trace:
[<ffffffff8116e2b9>] dump_stack+0x40/0x57
[<ffffffffa020b88d>] vmx_cpuid_update+0x5d/0x150 [kvm_intel]
[<ffffffffa01d8fdc>] kvm_vcpu_ioctl_set_cpuid2+0x4c/0x70 [kvm]
[<ffffffffa01b8363>] kvm_arch_vcpu_ioctl+0x903/0xfa0 [kvm]
Fixes: feda805fe7
Cc: stable@vger.kernel.org
Reported-by: Zdenek Kaspar <zkaspar82@gmail.com>
Signed-off-by: Huaitong Han <huaitong.han@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
---
I am sending this as RFC because the error messages it produces are
very ugly. Because of inlining, the original line is lost. The
alternative is to change vmcs_read/write/checkXX into macros, but
then you need to have a single huge BUILD_BUG_ON or BUILD_BUG_ON_MSG
because multiple BUILD_BUG_ON* with the same __LINE__ are not
supported well.
This was not printing the high parts of several 64-bit fields on
32-bit kernels. Separate from the previous one to make the patches
easier to review.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In theory this should have broken EPT on 32-bit kernels (due to
reading the high part of natural-width field GUEST_CR3). Not sure
if no one noticed or the processor behaves differently from the
documentation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The current handling of accesses to guest MSR_TSC_AUX returns error if
vcpu does not support rdtscp, though those accesses are initiated by
host. This can result in the reboot failure of some versions of
QEMU. This patch fixes this issue by passing those host initiated
accesses for further handling instead.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The decision on whether to use hardware APIC virtualization used to be
taken globally, based on the availability of the feature in the CPU
and the value of a module parameter.
However, under certain circumstances we want to control it on per-vcpu
basis. In particular, when the userspace activates HyperV synthetic
interrupt controller (SynIC), APICv has to be disabled as it's
incompatible with SynIC auto-EOI behavior.
To achieve that, introduce 'apicv_active' flag on struct
kvm_vcpu_arch, and kvm_vcpu_deactivate_apicv() function to turn APICv
off. The flag is initialized based on the module parameter and CPU
capability, and consulted whenever an APICv-specific action is
performed.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The function to determine if the vector is handled by ioapic used to
rely on the fact that only ioapic-handled vectors were set up to
cause vmexits when virtual apic was in use.
We're going to break this assumption when introducing Hyper-V
synthetic interrupts: they may need to cause vmexits too.
To achieve that, introduce a new bitmap dedicated specifically for
ioapic-handled vectors, and populate EOI exit bitmap from it for now.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch removes the vpid check when emulating nested invvpid
instruction of type all-contexts invalidation. The existing code is
incorrect because:
(1) According to Intel SDM Vol 3, Section "INVVPID - Invalidate
Translations Based on VPID", invvpid instruction does not check
vpid in the invvpid descriptor when its type is all-contexts
invalidation.
(2) According to the same document, invvpid of type all-contexts
invalidation does not require there is an active VMCS, so/and
get_vmcs12() in the existing code may result in a NULL-pointer
dereference. In practice, it can crash both KVM itself and L1
hypervisors that use invvpid (e.g. Xen).
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because #DB is now intercepted unconditionally, this callback
only operates on #BP for both VMX and SVM.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It was found that a guest can DoS a host by triggering an infinite
stream of "alignment check" (#AC) exceptions. This causes the
microcode to enter an infinite loop where the core never receives
another interrupt. The host kernel panics pretty quickly due to the
effects (CVE-2015-5307).
Signed-off-by: Eric Northup <digitaleric@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch enhances dump_vmcs() to dump the value of TSC multiplier
field in VMCS.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch makes kvm-intel to return a scaled host TSC plus the TSC
offset when handling guest readings to MSR_IA32_TSC.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch makes kvm-intel module to load TSC scaling ratio into TSC
multiplier field of VMCS when a vcpu is loaded, so that TSC scaling
ratio can take effect if VMX TSC scaling is enabled.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch exhances kvm-intel module to enable VMX TSC scaling and
collects information of TSC scaling ratio during initialization.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For both VMX and SVM, if the 2nd argument of call-back
adjust_tsc_offset() is the host TSC, then adjust_tsc_offset() will scale
it first. This patch moves this common TSC scaling logic to its caller
adjust_tsc_offset_host() and rename the call-back adjust_tsc_offset() to
adjust_tsc_offset_guest().
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both VMX and SVM calculate the tsc-offset in the same way, so this
patch removes the call-back compute_tsc_offset() and replaces it with a
common function kvm_compute_tsc_offset().
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both VMX and SVM propagate virtual_tsc_khz in the same way, so this
patch removes the call-back set_tsc_khz() and replaces it with a common
function.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
They are exactly the same, except that handle_mmio_page_fault
has an unused argument and a call to WARN_ON. Remove the unused
argument from the callers, and move the warning to (the former)
handle_mmio_page_fault_common.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I found PML was broken since below commit:
commit feda805fe7
Author: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Date: Wed Sep 9 14:05:55 2015 +0800
KVM: VMX: unify SECONDARY_VM_EXEC_CONTROL update
Unify the update in vmx_cpuid_update()
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
[Rewrite to use vmcs_set_secondary_exec_control. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The reason is in above commit vmx_cpuid_update calls vmx_secondary_exec_control,
in which currently SECONDARY_EXEC_ENABLE_PML bit is cleared unconditionally (as
PML is enabled in creating vcpu). Therefore if vcpu_cpuid_update is called after
vcpu is created, PML will be disabled unexpectedly while log-dirty code still
thinks PML is used.
Fix this by clearing SECONDARY_EXEC_ENABLE_PML in vmx_secondary_exec_control
only when PML is not supported or not enabled (!enable_pml). This is more
reasonable as PML is currently either always enabled or disabled. With this
explicit updating SECONDARY_EXEC_ENABLE_PML in vmx_enable{disable}_pml is not
needed so also rename vmx_enable{disable}_pml to vmx_create{destroy}_pml_buffer.
Fixes: feda805fe7
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
[While at it, change a wrong ASSERT to an "if". The condition can happen
if creating the VCPU fails with ENOMEM. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The comment in code had it mostly right, but we enable paging for
emulated real mode regardless of EPT.
Without EPT (which implies emulated real mode), secondary VCPUs won't
start unless we disable SM[AE]P when the guest doesn't use paging.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Not zeroing EFER means that a 32-bit firmware cannot enter paging mode
without clearing EFER.LME first (which it should not know about).
Yang Zhang from Intel confirmed that the manual is wrong and EFER is
cleared to zero on INIT.
Fixes: d28bc9dd25
Cc: stable@vger.kernel.org
Cc: Yang Z Zhang <yang.z.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose VPID capability to L1. For nested guests, we don't do anything
specific for single context invalidation. Hence, only advertise support
for global context invalidation. The major benefit of nested VPID comes
from having separate vpids when switching between L1 and L2, and also
when L2's vCPUs not sched in/out on L1.
Reviewed-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VPID is used to tag address space and avoid a TLB flush. Currently L0 use
the same VPID to run L1 and all its guests. KVM flushes VPID when switching
between L1 and L2.
This patch advertises VPID to the L1 hypervisor, then address space of L1
and L2 can be separately treated and avoid TLB flush when swithing between
L1 and L2. For each nested vmentry, if vpid12 is changed, reuse shadow vpid
w/ an invvpid.
Performance:
run lmbench on L2 w/ 3.5 kernel.
Context switching - times in microseconds - smaller is better
-------------------------------------------------------------------------
Host OS 2p/0K 2p/16K 2p/64K 8p/16K 8p/64K 16p/16K 16p/64K
ctxsw ctxsw ctxsw ctxsw ctxsw ctxsw ctxsw
--------- ------------- ------ ------ ------ ------ ------ ------- -------
kernel Linux 3.5.0-1 1.2200 1.3700 1.4500 4.7800 2.3300 5.60000 2.88000 nested VPID
kernel Linux 3.5.0-1 1.2600 1.4300 1.5600 12.7 12.9 3.49000 7.46000 vanilla
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the INVVPID instruction emulation.
Reviewed-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce __vmx_flush_tlb() to handle specific vpid.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Adjust allocate/free_vid so that they can be reused for the nested vpid.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This merge brings in a couple important SMM fixes, which makes it
easier to test latest KVM with unrestricted_guest=0 and to test
the in-progress work on SMM support in the firmware.
Conflicts:
arch/x86/kvm/x86.c
The next patch will make x86_set_memory_region fill the
userspace_addr. Since the struct is not used untouched
anymore, it makes sense to build it in x86_set_memory_region
directly; it also simplifies the callers.
Reported-by: Alexandre DERUMIER <aderumier@odiso.com>
Cc: stable@vger.kernel.org
Fixes: 9da0e4d5ac
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch updates the Posted-Interrupts Descriptor when vCPU
is blocked.
pre-block:
- Add the vCPU to the blocked per-CPU list
- Set 'NV' to POSTED_INTR_WAKEUP_VECTOR
post-block:
- Remove the vCPU from the per-CPU list
Signed-off-by: Feng Wu <feng.wu@intel.com>
[Concentrate invocation of pre/post-block hooks to vcpu_block. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch updates the Posted-Interrupts Descriptor when vCPU
is preempted.
sched out:
- Set 'SN' to suppress furture non-urgent interrupts posted for
the vCPU.
sched in:
- Clear 'SN'
- Change NDST if vCPU is scheduled to a different CPU
- Set 'NV' to POSTED_INTR_VECTOR
Signed-off-by: Feng Wu <feng.wu@intel.com>
[Include asm/cpu.h to fix !CONFIG_SMP compilation. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds the routine to update IRTE for posted-interrupts
when guest changes the interrupt configuration.
Signed-off-by: Feng Wu <feng.wu@intel.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[Squashed in automatically generated patch from the build robot
"KVM: x86: vcpu_to_pi_desc() can be static" - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds some helper functions to manipulate the
Posted-Interrupts Descriptor.
Signed-off-by: Feng Wu <feng.wu@intel.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
[Make the new functions inline. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use vmcs_set_bits() and vmcs_clear_bits() to clean up the code
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unify the update in vmx_cpuid_update()
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
[Rewrite to use vmcs_set_secondary_exec_control. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If vmx_invpcid_supported() is true, second execution control
filed must be supported and SECONDARY_EXEC_ENABLE_INVPCID
must have already been set in current vmcs by
vmx_secondary_exec_control()
If vmx_invpcid_supported() is false, no need to clear
SECONDARY_EXEC_ENABLE_INVPCID
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
if vmx_rdtscp_supported() is true SECONDARY_EXEC_RDTSCP must
have already been set in current vmcs by
vmx_secondary_exec_control()
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SECONDARY_EXEC_RDTSCP set for L2 guest comes from vmcs12
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pass PCOMMIT CPU feature to guest to enable PCOMMIT instruction
Currently we do not catch pcommit instruction for L1 guest and
allow L1 to catch this instruction for L2 if, as required by the spec,
L1 can enumerate the PCOMMIT instruction via CPUID:
| IA32_VMX_PROCBASED_CTLS2[53] (which enumerates support for the
| 1-setting of PCOMMIT exiting) is always the same as
| CPUID.07H:EBX.PCOMMIT[bit 22]. Thus, software can set PCOMMIT exiting
| to 1 if and only if the PCOMMIT instruction is enumerated via CPUID
The spec can be found at
https://software.intel.com/sites/default/files/managed/0d/53/319433-022.pdf
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Uniprocessor 32-bit randconfigs can disable the local APIC, and posted
interrupts require reserving a vector on the LAPIC, so they are
incompatible.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The interrupt window is currently checked twice, once in vmx.c/svm.c and
once in dm_request_for_irq_injection. The only difference is the extra
check for kvm_arch_interrupt_allowed in dm_request_for_irq_injection,
and the different return value (EINTR/KVM_EXIT_INTR for vmx.c/svm.c vs.
0/KVM_EXIT_IRQ_WINDOW_OPEN for dm_request_for_irq_injection).
However, dm_request_for_irq_injection is basically dead code! Revive it
by removing the checks in vmx.c and svm.c's vmexit handlers, and
fixing the returned values for the dm_request_for_irq_injection case.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Avoid pointer chasing and memory barriers, and simplify the code
when split irqchip (LAPIC in kernel, IOAPIC/PIC in userspace)
is introduced.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can reuse the algorithm that computes the EOI exit bitmap to figure
out which vectors are handled by the IOAPIC. The only difference
between the two is for edge-triggered interrupts other than IRQ8
that have no notifiers active; however, the IOAPIC does not have to
do anything special for these interrupts anyway.
This again limits the interactions between the IOAPIC and the LAPIC,
making it easier to move the former to userspace.
Inspired by a patch from Steve Rutherford.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit fd717f1101.
It was reported to cause Machine Check Exceptions (bug 104091).
Reported-by: harn-solo@gmx.de
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reference SDM 28.1:
The current VPID is 0000H in the following situations:
- Outside VMX operation. (This includes operation in system-management
mode under the default treatment of SMIs and SMM with VMX operation;
see Section 34.14.)
- In VMX root operation.
- In VMX non-root operation when the “enable VPID” VM-execution control
is 0.
The VPID should never be 0000H in non-root operation when "enable VPID"
VM-execution control is 1. However, commit 34a1cd60 ("kvm: x86: vmx:
move some vmx setting from vmx_init() to hardware_setup()") remove the
codes which reserve 0000H for VMX root operation.
This patch fix it by again reserving 0000H for VMX root operation.
Cc: stable@vger.kernel.org # 3.19+
Fixes: 34a1cd60d1
Reported-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are two kexec load syscalls, kexec_load another and kexec_file_load.
kexec_file_load has been splited as kernel/kexec_file.c. In this patch I
split kexec_load syscall code to kernel/kexec.c.
And add a new kconfig option KEXEC_CORE, so we can disable kexec_load and
use kexec_file_load only, or vice verse.
The original requirement is from Ted Ts'o, he want kexec kernel signature
being checked with CONFIG_KEXEC_VERIFY_SIG enabled. But kexec-tools use
kexec_load syscall can bypass the checking.
Vivek Goyal proposed to create a common kconfig option so user can compile
in only one syscall for loading kexec kernel. KEXEC/KEXEC_FILE selects
KEXEC_CORE so that old config files still work.
Because there's general code need CONFIG_KEXEC_CORE, so I updated all the
architecture Kconfig with a new option KEXEC_CORE, and let KEXEC selects
KEXEC_CORE in arch Kconfig. Also updated general kernel code with to
kexec_load syscall.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alloc_pages_exact_node() was introduced in commit 6484eb3e2a ("page
allocator: do not check NUMA node ID when the caller knows the node is
valid") as an optimized variant of alloc_pages_node(), that doesn't
fallback to current node for nid == NUMA_NO_NODE. Unfortunately the
name of the function can easily suggest that the allocation is
restricted to the given node and fails otherwise. In truth, the node is
only preferred, unless __GFP_THISNODE is passed among the gfp flags.
The misleading name has lead to mistakes in the past, see for example
commits 5265047ac3 ("mm, thp: really limit transparent hugepage
allocation to local node") and b360edb43f ("mm, mempolicy:
migrate_to_node should only migrate to node").
Another issue with the name is that there's a family of
alloc_pages_exact*() functions where 'exact' means exact size (instead
of page order), which leads to more confusion.
To prevent further mistakes, this patch effectively renames
alloc_pages_exact_node() to __alloc_pages_node() to better convey that
it's an optimized variant of alloc_pages_node() not intended for general
usage. Both functions get described in comments.
It has been also considered to really provide a convenience function for
allocations restricted to a node, but the major opinion seems to be that
__GFP_THISNODE already provides that functionality and we shouldn't
duplicate the API needlessly. The number of users would be small
anyway.
Existing callers of alloc_pages_exact_node() are simply converted to
call __alloc_pages_node(), with the exception of sba_alloc_coherent()
which open-codes the check for NUMA_NO_NODE, so it is converted to use
alloc_pages_node() instead. This means it no longer performs some
VM_BUG_ON checks, and since the current check for nid in
alloc_pages_node() uses a 'nid < 0' comparison (which includes
NUMA_NO_NODE), it may hide wrong values which would be previously
exposed.
Both differences will be rectified by the next patch.
To sum up, this patch makes no functional changes, except temporarily
hiding potentially buggy callers. Restricting the checks in
alloc_pages_node() is left for the next patch which can in turn expose
more existing buggy callers.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Robin Holt <robinmholt@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Christoph Lameter <cl@linux.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Mel Gorman <mgorman@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Cliff Whickman <cpw@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 asm changes from Ingo Molnar:
"The biggest changes in this cycle were:
- Revamp, simplify (and in some cases fix) Time Stamp Counter (TSC)
primitives. (Andy Lutomirski)
- Add new, comprehensible entry and exit handlers written in C.
(Andy Lutomirski)
- vm86 mode cleanups and fixes. (Brian Gerst)
- 32-bit compat code cleanups. (Brian Gerst)
The amount of simplification in low level assembly code is already
palpable:
arch/x86/entry/entry_32.S | 130 +----
arch/x86/entry/entry_64.S | 197 ++-----
but more simplifications are planned.
There's also the usual laudry mix of low level changes - see the
changelog for details"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (83 commits)
x86/asm: Drop repeated macro of X86_EFLAGS_AC definition
x86/asm/msr: Make wrmsrl() a function
x86/asm/delay: Introduce an MWAITX-based delay with a configurable timer
x86/asm: Add MONITORX/MWAITX instruction support
x86/traps: Weaken context tracking entry assertions
x86/asm/tsc: Add rdtscll() merge helper
selftests/x86: Add syscall_nt selftest
selftests/x86: Disable sigreturn_64
x86/vdso: Emit a GNU hash
x86/entry: Remove do_notify_resume(), syscall_trace_leave(), and their TIF masks
x86/entry/32: Migrate to C exit path
x86/entry/32: Remove 32-bit syscall audit optimizations
x86/vm86: Rename vm86->v86flags and v86mask
x86/vm86: Rename vm86->vm86_info to user_vm86
x86/vm86: Clean up vm86.h includes
x86/vm86: Move the vm86 IRQ definitions to vm86.h
x86/vm86: Use the normal pt_regs area for vm86
x86/vm86: Eliminate 'struct kernel_vm86_struct'
x86/vm86: Move fields from 'struct kernel_vm86_struct' to 'struct vm86'
x86/vm86: Move vm86 fields out of 'thread_struct'
...
VMX encodes access rights differently from LAR, and the latter is
most likely what x86 people think of when they think of "access
rights".
Rename them to avoid confusion.
Cc: kvm@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The logic used to check ept misconfig is completely contained in common
reserved bits check for sptes, so it can be removed
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow a nested hypervisor to single step its guests.
Signed-off-by: Mihai Donțu <mihai.dontu@gmail.com>
[Fix overlong line. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to Intel SDM several checks must be applied for memory operands
of VMX instructions.
Long mode: #GP(0) or #SS(0) depending on the segment must be thrown
if the memory address is in a non-canonical form.
Protected mode, checks in chronological order:
- The segment type must be checked with access type (read or write) taken
into account.
For write access: #GP(0) must be generated if the destination operand
is located in a read-only data segment or any code segment.
For read access: #GP(0) must be generated if if the source operand is
located in an execute-only code segment.
- Usability of the segment must be checked. #GP(0) or #SS(0) depending on the
segment must be thrown if the segment is unusable.
- Limit check. #GP(0) or #SS(0) depending on the segment must be
thrown if the memory operand effective address is outside the segment
limit.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make them clearly architecture-dependent; the capability is valid for
all architectures, but the argument is not.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
OVMF depends on WB to boot fast, because it only clears caches after
it has set up MTRRs---which is too late.
Let's do writeback if CR0.CD is set to make it happy, similar to what
SVM is already doing.
Signed-off-by: Xiao Guangrong <guangrong.xiao@intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently guest MTRR is avoided if kvm_is_reserved_pfn returns true.
However, the guest could prefer a different page type than UC for
such pages. A good example is that pass-throughed VGA frame buffer is
not always UC as host expected.
This patch enables full use of virtual guest MTRRs.
Suggested-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Tested-by: Joerg Roedel <jroedel@suse.de> (on AMD)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that there is no paravirt TSC, the "native" is
inappropriate. The function does RDTSC, so give it the obvious
name: rdtsc().
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/fd43e16281991f096c1e4d21574d9e1402c62d39.1434501121.git.luto@kernel.org
[ Ported it to v4.2-rc1. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that the ->read_tsc() paravirt hook is gone, rdtscll() is
just a wrapper around native_read_tsc(). Unwrap it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/d2449ae62c1b1fb90195bcfb19ef4a35883a04dc.1434501121.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
"monitonic raw". Also some enhancements to make the ring buffer even
faster. But the biggest and most noticeable change is the renaming of
the ftrace* files, structures and variables that have to deal with
trace events.
Over the years I've had several developers tell me about their confusion
with what ftrace is compared to events. Technically, "ftrace" is the
infrastructure to do the function hooks, which include tracing and also
helps with live kernel patching. But the trace events are a separate
entity altogether, and the files that affect the trace events should
not be named "ftrace". These include:
include/trace/ftrace.h -> include/trace/trace_events.h
include/linux/ftrace_event.h -> include/linux/trace_events.h
Also, functions that are specific for trace events have also been renamed:
ftrace_print_*() -> trace_print_*()
(un)register_ftrace_event() -> (un)register_trace_event()
ftrace_event_name() -> trace_event_name()
ftrace_trigger_soft_disabled()-> trace_trigger_soft_disabled()
ftrace_define_fields_##call() -> trace_define_fields_##call()
ftrace_get_offsets_##call() -> trace_get_offsets_##call()
Structures have been renamed:
ftrace_event_file -> trace_event_file
ftrace_event_{call,class} -> trace_event_{call,class}
ftrace_event_buffer -> trace_event_buffer
ftrace_subsystem_dir -> trace_subsystem_dir
ftrace_event_raw_##call -> trace_event_raw_##call
ftrace_event_data_offset_##call-> trace_event_data_offset_##call
ftrace_event_type_funcs_##call -> trace_event_type_funcs_##call
And a few various variables and flags have also been updated.
This has been sitting in linux-next for some time, and I have not heard
a single complaint about this rename breaking anything. Mostly because
these functions, variables and structures are mostly internal to the
tracing system and are seldom (if ever) used by anything external to that.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJViYhVAAoJEEjnJuOKh9ldcJ0IAI+mytwoMAN/CWDE8pXrTrgs
aHlcr1zorSzZ0Lq6lKsWP+V0VGVhP8KWO16vl35HaM5ZB9U+cDzWiGobI8JTHi/3
eeTAPTjQdgrr/L+ZO1ApzS1jYPhN3Xi5L7xublcYMJjKfzU+bcYXg/x8gRt0QbG3
S9QN/kBt0JIIjT7McN64m5JVk2OiU36LxXxwHgCqJvVCPHUrriAdIX7Z5KRpEv13
zxgCN4d7Jiec/FsMW8dkO0vRlVAvudZWLL7oDmdsvNhnLy8nE79UOeHos2c1qifQ
LV4DeQ+2Hlu7w9wxixHuoOgNXDUEiQPJXzPc/CuCahiTL9N/urQSGQDoOVMltR4=
=hkdz
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This patch series contains several clean ups and even a new trace
clock "monitonic raw". Also some enhancements to make the ring buffer
even faster. But the biggest and most noticeable change is the
renaming of the ftrace* files, structures and variables that have to
deal with trace events.
Over the years I've had several developers tell me about their
confusion with what ftrace is compared to events. Technically,
"ftrace" is the infrastructure to do the function hooks, which include
tracing and also helps with live kernel patching. But the trace
events are a separate entity altogether, and the files that affect the
trace events should not be named "ftrace". These include:
include/trace/ftrace.h -> include/trace/trace_events.h
include/linux/ftrace_event.h -> include/linux/trace_events.h
Also, functions that are specific for trace events have also been renamed:
ftrace_print_*() -> trace_print_*()
(un)register_ftrace_event() -> (un)register_trace_event()
ftrace_event_name() -> trace_event_name()
ftrace_trigger_soft_disabled() -> trace_trigger_soft_disabled()
ftrace_define_fields_##call() -> trace_define_fields_##call()
ftrace_get_offsets_##call() -> trace_get_offsets_##call()
Structures have been renamed:
ftrace_event_file -> trace_event_file
ftrace_event_{call,class} -> trace_event_{call,class}
ftrace_event_buffer -> trace_event_buffer
ftrace_subsystem_dir -> trace_subsystem_dir
ftrace_event_raw_##call -> trace_event_raw_##call
ftrace_event_data_offset_##call-> trace_event_data_offset_##call
ftrace_event_type_funcs_##call -> trace_event_type_funcs_##call
And a few various variables and flags have also been updated.
This has been sitting in linux-next for some time, and I have not
heard a single complaint about this rename breaking anything. Mostly
because these functions, variables and structures are mostly internal
to the tracing system and are seldom (if ever) used by anything
external to that"
* tag 'trace-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (33 commits)
ring_buffer: Allow to exit the ring buffer benchmark immediately
ring-buffer-benchmark: Fix the wrong type
ring-buffer-benchmark: Fix the wrong param in module_param
ring-buffer: Add enum names for the context levels
ring-buffer: Remove useless unused tracing_off_permanent()
ring-buffer: Give NMIs a chance to lock the reader_lock
ring-buffer: Add trace_recursive checks to ring_buffer_write()
ring-buffer: Allways do the trace_recursive checks
ring-buffer: Move recursive check to per_cpu descriptor
ring-buffer: Add unlikelys to make fast path the default
tracing: Rename ftrace_get_offsets_##call() to trace_event_get_offsets_##call()
tracing: Rename ftrace_define_fields_##call() to trace_event_define_fields_##call()
tracing: Rename ftrace_event_type_funcs_##call to trace_event_type_funcs_##call
tracing: Rename ftrace_data_offset_##call to trace_event_data_offset_##call
tracing: Rename ftrace_raw_##call event structures to trace_event_raw_##call
tracing: Rename ftrace_trigger_soft_disabled() to trace_trigger_soft_disabled()
tracing: Rename FTRACE_EVENT_FL_* flags to EVENT_FILE_FL_*
tracing: Rename struct ftrace_subsystem_dir to trace_subsystem_dir
tracing: Rename ftrace_event_name() to trace_event_name()
tracing: Rename FTRACE_MAX_EVENT to TRACE_EVENT_TYPE_MAX
...
for silicon that no one owns: these are really new features for
everyone.
* ARM: several features are in progress but missed the 4.2 deadline.
So here is just a smattering of bug fixes, plus enabling the VFIO
integration.
* s390: Some fixes/refactorings/optimizations, plus support for
2GB pages.
* x86: 1) host and guest support for marking kvmclock as a stable
scheduler clock. 2) support for write combining. 3) support for
system management mode, needed for secure boot in guests. 4) a bunch
of cleanups required for 2+3. 5) support for virtualized performance
counters on AMD; 6) legacy PCI device assignment is deprecated and
defaults to "n" in Kconfig; VFIO replaces it. On top of this there are
also bug fixes and eager FPU context loading for FPU-heavy guests.
* Common code: Support for multiple address spaces; for now it is
used only for x86 SMM but the s390 folks also have plans.
There are some x86 conflicts, one with the rc8 pull request and
the rest with Ingo's FPU rework.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJViYzhAAoJEL/70l94x66Dda0H/1IepMbfEy+o849d5G71fNTs
F8Y8qUP2GZuL7T53FyFUGSBw+AX7kimu9ia4gR/PmDK+QYsdosYeEjwlsolZfTBf
sHuzNtPoJhi5o1o/ur4NGameo0WjGK8f1xyzr+U8z74QDQyQv/QYCdK/4isp4BJL
ugHNHkuROX6Zng4i7jc9rfaSRg29I3GBxQUYpMkEnD3eMYMUBWGm6Rs8pHgGAMvL
vqzntgW00WNxehTqcAkmD/Wv+txxhkvIadZnjgaxH49e9JeXeBKTIR5vtb7Hns3s
SuapZUyw+c95DIipXq4EznxxaOrjbebOeFgLCJo8+XMXZum8RZf/ob24KroYad0=
=YsAR
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull first batch of KVM updates from Paolo Bonzini:
"The bulk of the changes here is for x86. And for once it's not for
silicon that no one owns: these are really new features for everyone.
Details:
- ARM:
several features are in progress but missed the 4.2 deadline.
So here is just a smattering of bug fixes, plus enabling the
VFIO integration.
- s390:
Some fixes/refactorings/optimizations, plus support for 2GB
pages.
- x86:
* host and guest support for marking kvmclock as a stable
scheduler clock.
* support for write combining.
* support for system management mode, needed for secure boot in
guests.
* a bunch of cleanups required for the above
* support for virtualized performance counters on AMD
* legacy PCI device assignment is deprecated and defaults to "n"
in Kconfig; VFIO replaces it
On top of this there are also bug fixes and eager FPU context
loading for FPU-heavy guests.
- Common code:
Support for multiple address spaces; for now it is used only for
x86 SMM but the s390 folks also have plans"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (124 commits)
KVM: s390: clear floating interrupt bitmap and parameters
KVM: x86/vPMU: Enable PMU handling for AMD PERFCTRn and EVNTSELn MSRs
KVM: x86/vPMU: Implement AMD vPMU code for KVM
KVM: x86/vPMU: Define kvm_pmu_ops to support vPMU function dispatch
KVM: x86/vPMU: introduce kvm_pmu_msr_idx_to_pmc
KVM: x86/vPMU: reorder PMU functions
KVM: x86/vPMU: whitespace and stylistic adjustments in PMU code
KVM: x86/vPMU: use the new macros to go between PMC, PMU and VCPU
KVM: x86/vPMU: introduce pmu.h header
KVM: x86/vPMU: rename a few PMU functions
KVM: MTRR: do not map huge page for non-consistent range
KVM: MTRR: simplify kvm_mtrr_get_guest_memory_type
KVM: MTRR: introduce mtrr_for_each_mem_type
KVM: MTRR: introduce fixed_mtrr_addr_* functions
KVM: MTRR: sort variable MTRRs
KVM: MTRR: introduce var_mtrr_range
KVM: MTRR: introduce fixed_mtrr_segment table
KVM: MTRR: improve kvm_mtrr_get_guest_memory_type
KVM: MTRR: do not split 64 bits MSR content
KVM: MTRR: clean up mtrr default type
...
This patch defines a new function pointer struct (kvm_pmu_ops) to
support vPMU for both Intel and AMD. The functions pointers defined in
this new struct will be linked with Intel and AMD functions later. In the
meanwhile the struct that maps from event_sel bits to PERF_TYPE_HARDWARE
events is renamed and moved from Intel specific code to kvm_host.h as a
common struct.
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MTRR code locates in x86.c and mmu.c so that move them to a separate file to
make the organization more clearer and it will be the place where we fully
implement vMTRR
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, CR0.CD is not checked when we virtualize memory cache type for
noncoherent_dma guests, this patch fixes it by :
- setting UC for all memory if CR0.CD = 1
- zapping all the last sptes in MMU if CR0.CD is changed
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
... and we're done. :)
Because SMBASE is usually relocated above 1M on modern chipsets, and
SMM handlers might indeed rely on 4G segment limits, we only expose it
if KVM is able to run the guest in big real mode. This includes any
of VMX+emulate_invalid_guest_state, VMX+unrestricted_guest, or SVM.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch has no semantic change, but it prepares for the introduction
of a second address space for system management mode.
A new function x86_set_memory_region (and the "slots_lock taken"
counterpart __x86_set_memory_region) is introduced in order to
operate on all address spaces when adding or deleting private
memory slots.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We need to hide SMRAM from guests not running in SMM. Therefore,
all uses of kvm_read_guest* and kvm_write_guest* must be changed to
check whether the VCPU is in system management mode and use a
different set of memslots. Switch from kvm_* to the newly-introduced
kvm_vcpu_*, which call into kvm_arch_vcpu_memslots_id.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SMBASE is only readable from SMM for the VCPU, but it must be always
accessible if userspace is accessing it. Thus, all functions that
read MSRs are changed to accept a struct msr_data; the host_initiated
and index fields are pre-initialized, while the data field is filled
on return.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the host sets hardware breakpoints to debug the guest, and a task-switch
occurs in the guest, the architectural DR7 will not be updated. The effective
DR7 would be updated instead.
This fix puts the DR7 update during task-switch emulation, so it now uses the
standard DR setting mechanism instead of the one that was previously used. As a
bonus, the update of DR7 will now be effective for AMD as well.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename this function in line with the new FPU nomenclature.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that all FPU internals using drivers are converted to public APIs,
move xcr.h's definitions into fpu/internal.h and remove xcr.h.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There are a number of FPU internal function prototypes and an inline function
in fpu/api.h, mostly placed so historically as the code grew over the years.
Move them over into fpu/internal.h where they belong. (Add sched.h include
to stackprotector.h which incorrectly relied on getting it from fpu/api.h.)
fpu/api.h is now a pure file that only contains FPU APIs intended for driver
use.
Reviewed-by: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We already have fpu/types.h, move i387.h to fpu/api.h.
The file name has become a misnomer anyway: it offers generic FPU APIs,
but is not limited to i387 functionality.
Reviewed-by: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The term "ftrace" is really the infrastructure of the function hooks,
and not the trace events. Rename ftrace_event.h to trace_events.h to
represent the trace_event infrastructure and decouple the term ftrace
from it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
vcpu->arch.apic is NULL when a userspace irqchip is active. But instead
of letting the test incorrectly depend on in-kernel irqchip mode,
open-code it to catch also userspace x2APICs.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
PAT should be 0007_0406_0007_0406h on RESET and not modified on INIT.
VMX used a wrong value (host's PAT) and while SVM used the right one,
it never got to arch.pat.
This is not an issue with QEMU as it will force the correct value.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x86 architecture defines differences between the reset and INIT sequences.
INIT does not initialize the FPU (including MMX, XMM, YMM, etc.), TSC, PMU,
MSRs (in general), MTRRs machine-check, APIC ID, APIC arbitration ID and BSP.
References (from Intel SDM):
"If the MP protocol has completed and a BSP is chosen, subsequent INITs (either
to a specific processor or system wide) do not cause the MP protocol to be
repeated." [8.4.2: MP Initialization Protocol Requirements and Restrictions]
[Table 9-1. IA-32 Processor States Following Power-up, Reset, or INIT]
"If the processor is reset by asserting the INIT# pin, the x87 FPU state is not
changed." [9.2: X87 FPU INITIALIZATION]
"The state of the local APIC following an INIT reset is the same as it is after
a power-up or hardware reset, except that the APIC ID and arbitration ID
registers are not affected." [10.4.7.3: Local APIC State After an INIT Reset
("Wait-for-SIPI" State)]
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1428924848-28212-1-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The host's decision to enable machine check exceptions should remain
in force during non-root mode. KVM was writing 0 to cr4 on VCPU reset
and passed a slightly-modified 0 to the vmcs.guest_cr4 value.
Tested: Built.
On earlier version, tested by injecting machine check
while a guest is spinning.
Before the change, if guest CR4.MCE==0, then the machine check is
escalated to Catastrophic Error (CATERR) and the machine dies.
If guest CR4.MCE==1, then the machine check causes VMEXIT and is
handled normally by host Linux. After the change, injecting a machine
check causes normal Linux machine check handling.
Signed-off-by: Ben Serebrin <serebrin@google.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ARM/ARM64: fixes for live migration, irqfd and ioeventfd support (enabling
vhost, too), page aging
s390: interrupt handling rework, allowing to inject all local interrupts
via new ioctl and to get/set the full local irq state for migration
and introspection. New ioctls to access memory by virtual address,
and to get/set the guest storage keys. SIMD support.
MIPS: FPU and MIPS SIMD Architecture (MSA) support. Includes some patches
from Ralf Baechle's MIPS tree.
x86: bugfixes (notably for pvclock, the others are small) and cleanups.
Another small latency improvement for the TSC deadline timer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJVJ9vmAAoJEL/70l94x66DoMEH/R3rh8IMf4jTiWRkcqohOMPX
k1+NaSY/lCKayaSgggJ2hcQenMbQoXEOdslvaA/H0oC+VfJGK+lmU6E63eMyyhjQ
Y+Px6L85NENIzDzaVu/TIWWuhil5PvIRr3VO8cvntExRoCjuekTUmNdOgCvN2ObW
wswN2qRdPIeEj2kkulbnye+9IV4G0Ne9bvsmUdOdfSSdi6ZcV43JcvrpOZT++mKj
RrKB+3gTMZYGJXMMLBwMkdl8mK1ozriD+q0mbomT04LUyGlPwYLl4pVRDBqyksD7
KsSSybaK2E4i5R80WEljgDMkNqrCgNfg6VZe4n9Y+CfAAOToNnkMJaFEi+yuqbs=
=yu2b
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"First batch of KVM changes for 4.1
The most interesting bit here is irqfd/ioeventfd support for ARM and
ARM64.
Summary:
ARM/ARM64:
fixes for live migration, irqfd and ioeventfd support (enabling
vhost, too), page aging
s390:
interrupt handling rework, allowing to inject all local interrupts
via new ioctl and to get/set the full local irq state for migration
and introspection. New ioctls to access memory by virtual address,
and to get/set the guest storage keys. SIMD support.
MIPS:
FPU and MIPS SIMD Architecture (MSA) support. Includes some
patches from Ralf Baechle's MIPS tree.
x86:
bugfixes (notably for pvclock, the others are small) and cleanups.
Another small latency improvement for the TSC deadline timer"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (146 commits)
KVM: use slowpath for cross page cached accesses
kvm: mmu: lazy collapse small sptes into large sptes
KVM: x86: Clear CR2 on VCPU reset
KVM: x86: DR0-DR3 are not clear on reset
KVM: x86: BSP in MSR_IA32_APICBASE is writable
KVM: x86: simplify kvm_apic_map
KVM: x86: avoid logical_map when it is invalid
KVM: x86: fix mixed APIC mode broadcast
KVM: x86: use MDA for interrupt matching
kvm/ppc/mpic: drop unused IRQ_testbit
KVM: nVMX: remove unnecessary double caching of MAXPHYADDR
KVM: nVMX: checks for address bits beyond MAXPHYADDR on VM-entry
KVM: x86: cache maxphyaddr CPUID leaf in struct kvm_vcpu
KVM: vmx: pass error code with internal error #2
x86: vdso: fix pvclock races with task migration
KVM: remove kvm_read_hva and kvm_read_hva_atomic
KVM: x86: optimize delivery of TSC deadline timer interrupt
KVM: x86: extract blocking logic from __vcpu_run
kvm: x86: fix x86 eflags fixed bit
KVM: s390: migrate vcpu interrupt state
...
After reset, the CPU can change the BSP, which will be used upon INIT. Reset
should return the BSP which QEMU asked for, and therefore handled accordingly.
To quote: "If the MP protocol has completed and a BSP is chosen, subsequent
INITs (either to a specific processor or system wide) do not cause the MP
protocol to be repeated."
[Intel SDM 8.4.2: MP Initialization Protocol Requirements and Restrictions]
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427933438-12782-3-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After speed-up of cpuid_maxphyaddr() it can be called frequently:
instead of heavyweight enumeration of CPUID entries it returns a cached
pre-computed value. It is also inlined now. So caching its result became
unnecessary and can be removed.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Message-Id: <20150329205644.GA1258@gnote>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On each VM-entry CPU should check the following VMCS fields for zero bits
beyond physical address width:
- APIC-access address
- virtual-APIC address
- posted-interrupt descriptor address
This patch adds these checks required by Intel SDM.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Message-Id: <20150329205627.GA1244@gnote>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Exposing the on-stack error code with internal error is cheap and
potentially useful.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <1428001865-32280-1-git-send-email-rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the normal return values for bool functions
Signed-off-by: Joe Perches <joe@perches.com>
Message-Id: <9f593eb2f43b456851cd73f7ed09654ca58fb570.1427759009.git.joe@perches.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some constants are redfined in emulate.c. Avoid it.
s/SELECTOR_RPL_MASK/SEGMENT_RPL_MASK
s/SELECTOR_TI_MASK/SEGMENT_TI_MASK
No functional change.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427635984-8113-3-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the guest CPU is supposed to support rdtscp and the host has rdtscp
enabled in the secondary execution controls, we can also expose this
feature to L1. Just extend nested_vmx_exit_handled to properly route
EXIT_REASON_RDTSCP.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This is needed in e.g. ARM vGIC emulation, where the MMIO handling
depends on the VCPU that does the access.
Signed-off-by: Nikolay Nikolaev <n.nikolaev@virtualopensystems.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If EPT was enabled, unrestricted_guest was allowed in L1 regardless of
L0. L1 triple faulted when running L2 guest that required emulation.
Another side effect was 'WARN_ON_ONCE(vmx->nested.nested_run_pending)'
in L0's dmesg:
WARNING: CPU: 0 PID: 0 at arch/x86/kvm/vmx.c:9190 nested_vmx_vmexit+0x96e/0xb00 [kvm_intel] ()
Prevent this scenario by masking SECONDARY_EXEC_UNRESTRICTED_GUEST when
the host doesn't have it enabled.
Fixes: 78051e3b7e ("KVM: nVMX: Disable unrestricted mode if ept=0")
Cc: stable@vger.kernel.org
Tested-By: Kashyap Chamarthy <kchamart@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
While in L2, leave all #UD to L2 and do not try to emulate it. If L1 is
interested in doing this, it reports its interest via the exception
bitmap, and we never get into handle_exception of L0 anyway.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
In commit 3af18d9c5f ("KVM: nVMX: Prepare for using hardware MSR bitmap"),
we are setting MSR_BITMAP in prepare_vmcs02 if we should use hardware. This
is not enough since the field will be modified by following vmx_set_efer.
Fix this by setting vmx_msr_bitmap_nested in vmx_set_msr_bitmap if vcpu is
in guest mode.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Currently kvm_emulate() skips the instruction but kvm_emulate_* sometimes
don't. The end reult is the caller ends up doing the skip themselves.
Let's make them consistant.
Signed-off-by: Joel Schopp <joel.schopp@amd.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
'apic' is not defined if !CONFIG_X86_64 && !CONFIG_X86_LOCAL_APIC.
Posted interrupt makes no sense without CONFIG_SMP, and
CONFIG_X86_LOCAL_APIC will be set with it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull x86 perf updates from Ingo Molnar:
"This series tightens up RDPMC permissions: currently even highly
sandboxed x86 execution environments (such as seccomp) have permission
to execute RDPMC, which may leak various perf events / PMU state such
as timing information and other CPU execution details.
This 'all is allowed' RDPMC mode is still preserved as the
(non-default) /sys/devices/cpu/rdpmc=2 setting. The new default is
that RDPMC access is only allowed if a perf event is mmap-ed (which is
needed to correctly interpret RDPMC counter values in any case).
As a side effect of these changes CR4 handling is cleaned up in the
x86 code and a shadow copy of the CR4 value is added.
The extra CR4 manipulation adds ~ <50ns to the context switch cost
between rdpmc-capable and rdpmc-non-capable mms"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Add /sys/devices/cpu/rdpmc=2 to allow rdpmc for all tasks
perf/x86: Only allow rdpmc if a perf_event is mapped
perf: Pass the event to arch_perf_update_userpage()
perf: Add pmu callbacks to track event mapping and unmapping
x86: Add a comment clarifying LDT context switching
x86: Store a per-cpu shadow copy of CR4
x86: Clean up cr4 manipulation
<asm/apic.h> isn't included directly and without CONFIG_SMP, an option
that automagically pulls it can't be enabled.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Context switches and TLB flushes can change individual bits of CR4.
CR4 reads take several cycles, so store a shadow copy of CR4 in a
per-cpu variable.
To avoid wasting a cache line, I added the CR4 shadow to
cpu_tlbstate, which is already touched in switch_mm. The heaviest
users of the cr4 shadow will be switch_mm and __switch_to_xtra, and
__switch_to_xtra is called shortly after switch_mm during context
switch, so the cacheline is likely to be hot.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Vince Weaver <vince@deater.net>
Cc: "hillf.zj" <hillf.zj@alibaba-inc.com>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/3a54dd3353fffbf84804398e00dfdc5b7c1afd7d.1414190806.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
CR4 manipulation was split, seemingly at random, between direct
(write_cr4) and using a helper (set/clear_in_cr4). Unfortunately,
the set_in_cr4 and clear_in_cr4 helpers also poke at the boot code,
which only a small subset of users actually wanted.
This patch replaces all cr4 access in functions that don't leave cr4
exactly the way they found it with new helpers cr4_set_bits,
cr4_clear_bits, and cr4_set_bits_and_update_boot.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Vince Weaver <vince@deater.net>
Cc: "hillf.zj" <hillf.zj@alibaba-inc.com>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/495a10bdc9e67016b8fd3945700d46cfd5c12c2f.1414190806.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If vcpu has a interrupt in vmx non-root mode, injecting that interrupt
requires a vmexit. With posted interrupt processing, the vmexit
is not needed, and interrupts are fully taken care of by hardware.
In nested vmx, this feature avoids much more vmexits than non-nested vmx.
When L1 asks L0 to deliver L1's posted interrupt vector, and the target
VCPU is in non-root mode, we use a physical ipi to deliver POSTED_INTR_NV
to the target vCPU. Using POSTED_INTR_NV avoids unexpected interrupts
if a concurrent vmexit happens and L1's vector is different with L0's.
The IPI triggers posted interrupt processing in the target physical CPU.
In case the target vCPU was not in guest mode, complete the posted
interrupt delivery on the next entry to L2.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With virtual interrupt delivery, the hardware lets KVM use a more
efficient mechanism for interrupt injection. This is an important feature
for nested VMX, because it reduces vmexits substantially and they are
much more expensive with nested virtualization. This is especially
important for throughput-bound scenarios.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can reduce apic register virtualization cost with this feature,
it is also a requirement for virtual interrupt delivery and posted
interrupt processing.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To enable nested apicv support, we need per-cpu vmx
control MSRs:
1. If in-kernel irqchip is enabled, we can enable nested
posted interrupt, we should set posted intr bit in
the nested_vmx_pinbased_ctls_high.
2. If in-kernel irqchip is disabled, we can not enable
nested posted interrupt, the posted intr bit
in the nested_vmx_pinbased_ctls_high will be cleared.
Since there would be different settings about in-kernel
irqchip between VMs, different nested control MSRs
are needed.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When L2 is using x2apic, we can use virtualize x2apic mode to
gain higher performance, especially in apicv case.
This patch also introduces nested_vmx_check_apicv_controls
for the nested apicv patches.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, if L1 enables MSR_BITMAP, we will emulate this feature, all
of L2's msr access is intercepted by L0. Features like "virtualize
x2apic mode" require that the MSR bitmap is enabled, or the hardware
will exit and for example not virtualize the x2apic MSRs. In order to
let L1 use these features, we need to build a merged bitmap that only
not cause a VMEXIT if 1) L1 requires that 2) the bit is not required by
the processor for APIC virtualization.
For now the guests are still run with MSR bitmap disabled, but this
patch already introduces nested_vmx_merge_msr_bitmap for future use.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Revert 7c6a98dfa1, given
that testing PIR is not necessary anymore.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A function pointer was not NULLed, causing kvm_vcpu_reload_apic_access_page to
go down the wrong path and OOPS when doing put_page(NULL).
This did not happen on old processors, only when setting the module option
explicitly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds PML support in VMX. A new module parameter 'enable_pml' is added
to allow user to enable/disable it manually.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Removes some functions that are not used anywhere:
cpu_has_vmx_eptp_writeback() cpu_has_vmx_eptp_uncacheable()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The initialization function in mmu.c can always use walk_mmu, which
is known to be vcpu->arch.mmu. Only init_kvm_nested_mmu is used to
initialize vcpu->arch.nested_mmu.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_x86_ops->test_posted_interrupt() returns true/false depending
whether 'vector' is set.
Next patch makes use of this interface.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In most cases calling hwapic_isr_update(), we always check if
kvm_apic_vid_enabled() == 1, but actually,
kvm_apic_vid_enabled()
-> kvm_x86_ops->vm_has_apicv()
-> vmx_vm_has_apicv() or '0' in svm case
-> return enable_apicv && irqchip_in_kernel(kvm)
So its a little cost to recall vmx_vm_has_apicv() inside
hwapic_isr_update(), here just NULL out hwapic_isr_update() in
case of !enable_apicv inside hardware_setup() then make all
related stuffs follow this. Note we don't check this under that
condition of irqchip_in_kernel() since we should make sure
definitely any caller don't work without in-kernel irqchip.
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When generating #PF VM-exit, check equality:
(PFEC & PFEC_MASK) == PFEC_MATCH
If there is equality, the 14 bit of exception bitmap is used to take decision
about generating #PF VM-exit. If there is inequality, inverted 14 bit is used.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch improve checks required by Intel Software Developer Manual.
- SMM MSRs are not allowed.
- microcode MSRs are not allowed.
- check x2apic MSRs only when LAPIC is in x2apic mode.
- MSR switch areas must be aligned to 16 bytes.
- address of first and last byte in MSR switch areas should not set any bits
beyond the processor's physical-address width.
Also it adds warning messages on failures during MSR switch. These messages
are useful for people who debug their VMMs in nVMX.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Several hypervisors need MSR auto load/restore feature.
We read MSRs from VM-entry MSR load area which specified by L1,
and load them via kvm_set_msr in the nested entry.
When nested exit occurs, we get MSRs via kvm_get_msr, writing
them to L1`s MSR store area. After this, we read MSRs from VM-exit
MSR load area, and load them via kvm_set_msr.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The commit 34a1cd60d1, "x86: vmx: move some vmx setting from
vmx_init() to hardware_setup()", tried to refactor some codes
specific to vmx hardware setting into hardware_setup(), but some
msr writing should depend on our previous setting condition like
enable_apicv, enable_ept and so on.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Tested-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If L0 has disabled EPT, don't advertise unrestricted
mode at all since it depends on EPT to run real mode code.
Fixes: 92fbc7b195
Cc: stable@vger.kernel.org
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add nested virtualization support for xsaves.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add logic to get/set the XSS model-specific register.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Initialize the XSS exit bitmap. It is zero so there should be no XSAVES
or XRSTORS exits.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose the XSAVES feature to the guest if the kvm_x86_ops say it is
available.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead, just use PFERR_{FETCH, PRESENT, WRITE}_MASK
inside handle_ept_violation() for slightly better code.
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There's nothing to switch if the host and guest values are the same.
I am unable to find evidence that this makes any difference
whatsoever.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
[I could see a difference on Nehalem. From 5 runs:
userspace exit, guest!=host 12200 11772 12130 12164 12327
userspace exit, guest=host 11983 11780 11920 11919 12040
lightweight exit, guest!=host 3214 3220 3238 3218 3337
lightweight exit, guest=host 3178 3193 3193 3187 3220
This passes the t-test with 99% confidence for userspace exit,
98.5% confidence for lightweight exit. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
At least on Sandy Bridge, letting the CPU switch IA32_EFER is much
faster than switching it manually.
I benchmarked this using the vmexit kvm-unit-test (single run, but
GOAL multiplied by 5 to do more iterations):
Test Before After Change
cpuid 2000 1932 -3.40%
vmcall 1914 1817 -5.07%
mov_from_cr8 13 13 0.00%
mov_to_cr8 19 19 0.00%
inl_from_pmtimer 19164 10619 -44.59%
inl_from_qemu 15662 10302 -34.22%
inl_from_kernel 3916 3802 -2.91%
outl_to_kernel 2230 2194 -1.61%
mov_dr 172 176 2.33%
ipi (skipped) (skipped)
ipi+halt (skipped) (skipped)
ple-round-robin 13 13 0.00%
wr_tsc_adjust_msr 1920 1845 -3.91%
rd_tsc_adjust_msr 1892 1814 -4.12%
mmio-no-eventfd:pci-mem 16394 11165 -31.90%
mmio-wildcard-eventfd:pci-mem 4607 4645 0.82%
mmio-datamatch-eventfd:pci-mem 4601 4610 0.20%
portio-no-eventfd:pci-io 11507 7942 -30.98%
portio-wildcard-eventfd:pci-io 2239 2225 -0.63%
portio-datamatch-eventfd:pci-io 2250 2234 -0.71%
I haven't explicitly computed the significance of these numbers,
but this isn't subtle.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
[The results were reproducible on all of Nehalem, Sandy Bridge and
Ivy Bridge. The slowness of manual switching is because writing
to EFER with WRMSR triggers a TLB flush, even if the only bit you're
touching is SCE (so the page table format is not affected). Doing
the write as part of vmentry/vmexit, instead, does not flush the TLB,
probably because all processors that have EPT also have VPID. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x86 debug registers hold a linear address. Therefore, breakpoints detection
should consider CS.base, and check whether instruction linear address equals
(CS.base + RIP). This patch introduces a function to evaluate RIP linear
address and uses it for breakpoints detection.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
DR6[0:3] (previous breakpoint indications) are cleared when #DB is injected
during handle_exception, just as real hardware does. Similarily, handle_dr
should clear DR6[0:3].
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A bug was reported as follows: when running Windows 7 32-bit guests on qemu-kvm,
sometimes the guests run into blue screen during reboot. The problem was that a
guest's RVI was not cleared when it rebooted. This patch has fixed the problem.
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Tested-by: Rongrong Liu <rongrongx.liu@intel.com>, Da Chun <ngugc@qq.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Return a negative error code instead, and WARN() when we should be covering
the entire 2-bit space of vmcs_field_type's return value. For increased
robustness, add a BUILD_BUG_ON checking the range of vmcs_field_to_offset.
Suggested-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of vmx_init(), actually it would make reasonable sense to do
anything specific to vmx hardware setting in vmx_x86_ops->hardware_setup().
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Just move this pair of functions down to make sure later we can
add something dependent on others.
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If DR4/5 is accessed when it is unavailable (since CR4.DE is set), then #UD
should be generated even if CPL>0. This is according to Intel SDM Table 6-2:
"Priority Among Simultaneous Exceptions and Interrupts".
Note, that this may happen on the first DR access, even if the host does not
sets debug breakpoints. Obviously, it occurs when the host debugs the guest.
This patch moves the DR4/5 checks from __kvm_set_dr/_kvm_get_dr to handle_dr.
The emulator already checks DR4/5 availability in check_dr_read. Nested
virutalization related calls to kvm_set_dr/kvm_get_dr would not like to inject
exceptions to the guest.
As for SVM, the patch follows the previous logic as much as possible. Anyhow,
it appears the DR interception code might be buggy - even if the DR access
may cause an exception, the instruction is skipped.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
DR7.LE should be cleared during task-switch. This feature is poorly documented.
For reference, see:
http://pdos.csail.mit.edu/6.828/2005/readings/i386/s12_02.htm
SDM [17.2.4]:
This feature is not supported in the P6 family processors, later IA-32
processors, and Intel 64 processors.
AMD [2:13.1.1.4]:
This bit is ignored by implementations of the AMD64 architecture.
Intel's formulation could mean that it isn't even zeroed, but current
hardware indeed does not behave like that.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel SDM 17.2.4 (Debug Control Register (DR7)) says: "The processor clears the
GD flag upon entering to the debug exception handler." This sentence may be
misunderstood as if it happens only on #DB due to debug-register protection,
but it happens regardless to the cause of the #DB.
Fix the behavior to match both real hardware and Bochs.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CR4.TSD is guest-owned; don't trap writes to it in VMX guests. This
avoids a VM exit on context switches into or out of a PR_TSC_SIGSEGV
task.
I think that this fixes an unintentional side-effect of:
4c38609ac5 KVM: VMX: Make guest cr4 mask more conservative
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
