__bnxt_xmit_xdp() is used by XDP_TX and ethtool loopback packet transmit.
Refactor it so that it can be re-used by the XDP_REDIRECT logic.
Restructure the TX interrupt handler logic to cleanly separate XDP_TX
logic in preparation for XDP_REDIRECT.
Acked-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming bnxt_xmit_xdp to __bnxt_xmit_xdp to get ready for XDP_REDIRECT
support and reduce confusion/namespace collision.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add XDP support based on rx page_pool allocator, one frame per page.
Page pool allocator is used with assumption that only one rx_handler
is running simultaneously. DMA map/unmap is reused from page pool
despite there is no need to map whole page.
Due to specific of cpsw, the same TX/RX handler can be used by 2
network devices, so special fields in buffer are added to identify
an interface the frame is destined to. Thus XDP works for both
interfaces, that allows to test xdp redirect between two interfaces
easily. Also, each rx queue have own page pools, but common for both
netdevs.
XDP prog is common for all channels till appropriate changes are added
in XDP infrastructure. Also, once page_pool recycling becomes part of
skb netstack some simplifications can be added, like removing
page_pool_release_page() before skb receive.
In order to keep rx_dev while redirect, that can be somehow used in
future, do flush in rx_handler, that allows to keep rx dev the same
while redirect. It allows to conform with tracing rx_dev pointed
by Jesper.
Also, there is probability, that XDP generic code can be extended to
support multi ndev drivers like this one, using same rx queue for
several ndevs, based on switchdev for instance or else. In this case,
driver can be modified like exposed here:
https://lkml.org/lkml/2019/7/3/243
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
That's possible to set channel num while interfaces are down. When
interface gets up it should resplit budget. This resplit can happen
after phy is up but only if speed is changed, so should be set before
this, for this allow it to happen while changing number of channels,
when interfaces are down.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
That's possible to set ring params while interfaces are down. When
interface gets up it uses number of descs to fill rx queue and on
later on changes to create rx pools. Usually, this resplit can happen
after phy is up, but it can be needed before this, so allow it to
happen while setting number of rx descs, when interfaces are down.
Also, if no dependency on intf state, move it to cpdma layer, where
it should be.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case if dma mapped packet needs to be sent, like with XDP
page pool, the "mapped" submit can be used. This patch adds dma
mapped submit based on regular one.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper recently removed page_pool_destroy() (from driver invocation)
and moved shutdown and free of page_pool into xdp_rxq_info_unreg(),
in-order to handle in-flight packets/pages. This created an asymmetry
in drivers create/destroy pairs.
This patch reintroduce page_pool_destroy and add page_pool user
refcnt. This serves the purpose to simplify drivers error handling as
driver now drivers always calls page_pool_destroy() and don't need to
track if xdp_rxq_info_reg_mem_model() was unsuccessful.
This could be used for a special cases where a single RX-queue (with a
single page_pool) provides packets for two net_device'es, and thus
needs to register the same page_pool twice with two xdp_rxq_info
structures.
This patch is primarily to ease API usage for drivers. The recently
merged netsec driver, actually have a bug in this area, which is
solved by this API change.
This patch is a modified version of Ivan Khoronzhuk's original patch.
Link: https://lore.kernel.org/netdev/20190625175948.24771-2-ivan.khoronzhuk@linaro.org/
Fixes: 5c67bf0ec4 ("net: netsec: Use page_pool API")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF is disabled, we get a harmless warning about the
newly added variable:
drivers/net/ethernet/cadence/macb_main.c:48:39: error: 'mgmt' defined but not used [-Werror=unused-variable]
static struct sifive_fu540_macb_mgmt *mgmt;
Move the variable closer to its use inside of the #ifdef.
Fixes: c218ad5590 ("macb: Add support for SiFive FU540-C000")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On unusual page sizes, we get harmless warnings:
drivers/net/ethernet/google/gve/gve_rx.c:283:6: error: unused variable 'pagecount' [-Werror,-Wunused-variable]
drivers/net/ethernet/google/gve/gve_rx.c:336:1: error: unused label 'have_skb' [-Werror,-Wunused-label]
Change the preprocessor #if to regular if() to avoid this.
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
"This is the wrong place to change the queue mapping.
stmmac_xmit() is called with a specific TX queue locked,
and accessing a different TX queue results in a data race
for all of that queue's state.
I think this commit should be reverted upstream and in all
stable branches. Instead, the driver should implement the
ndo_select_queue operation and override the queue mapping there."
Fixes: c5acdbee22 ("net: stmmac: Send TSO packets always from Queue 0")
Suggested-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is only at notice level but it was pointed out that no other driver
does this.
Also there is no action the user can take as it is really a property of
the server.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cd1973a921 ("net: netsec: Sync dma for device on buffer allocation")
was merged on it's v1 instead of the v3.
Merge the proper patch version
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer updates from Thomas Gleixner:
"The timer and timekeeping departement delivers:
Core:
- The consolidation of the VDSO code into a generic library including
the conversion of x86 and ARM64. Conversion of ARM and MIPS are en
route through the relevant maintainer trees and should end up in
5.4.
This gets rid of the unnecessary different copies of the same code
and brings all architectures on the same level of VDSO
functionality.
- Make the NTP user space interface more robust by restricting the
TAI offset to prevent undefined behaviour. Includes a selftest.
- Validate user input in the compat settimeofday() syscall to catch
invalid values which would be turned into valid values by a
multiplication overflow
- Consolidate the time accessors
- Small fixes, improvements and cleanups all over the place
Drivers:
- Support for the NXP system counter, TI davinci timer
- Move the Microsoft HyperV clocksource/events code into the
drivers/clocksource directory so it can be shared between x86 and
ARM64.
- Overhaul of the Tegra driver
- Delay timer support for IXP4xx
- Small fixes, improvements and cleanups as usual"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
time: Validate user input in compat_settimeofday()
timer: Document TIMER_PINNED
clocksource/drivers: Continue making Hyper-V clocksource ISA agnostic
clocksource/drivers: Make Hyper-V clocksource ISA agnostic
MAINTAINERS: Fix Andy's surname and the directory entries of VDSO
hrtimer: Use a bullet for the returns bullet list
arm64: vdso: Fix compilation with clang older than 8
arm64: compat: Fix __arch_get_hw_counter() implementation
arm64: Fix __arch_get_hw_counter() implementation
lib/vdso: Make delta calculation work correctly
MAINTAINERS: Add entry for the generic VDSO library
arm64: compat: No need for pre-ARMv7 barriers on an ARMv8 system
arm64: vdso: Remove unnecessary asm-offsets.c definitions
vdso: Remove superfluous #ifdef __KERNEL__ in vdso/datapage.h
clocksource/drivers/davinci: Add support for clocksource
clocksource/drivers/davinci: Add support for clockevents
clocksource/drivers/tegra: Set up maximum-ticks limit properly
clocksource/drivers/tegra: Cycles can't be 0
clocksource/drivers/tegra: Restore base address before cleanup
clocksource/drivers/tegra: Add verbose definition for 1MHz constant
...
This patch adds firmware version query in ethtool -i.
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probable cut&paste typo - use the correct field size.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probable cut&paste typo - use the correct field size.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an invalid role is sent from user space, gtp_encap_enable() will fail.
Then, it should call gtp_encap_disable_sock() but current code doesn't.
It makes memory leak.
Fixes: 91ed81f9ab ("gtp: support SGSN-side tunnels")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gtp_encap_disable() in gtp_dellink() is unnecessary because it will be
called by unregister_netdevice().
unregister_netdevice() internally calls gtp_dev_uninit() by ->ndo_uninit().
And gtp_dev_uninit() calls gtp_encap_disable().
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gtp_encap_destroy() is called twice.
1. When interface is deleted.
2. When udp socket is destroyed.
either gtp->sk0 or gtp->sk1u could be freed by sock_put() in
gtp_encap_destroy(). so, when gtp_encap_destroy() is called again,
it would uses freed sk pointer.
patch makes gtp_encap_destroy() to set either gtp->sk0 or gtp->sk1u to
null. in addition, both gtp->sk0 and gtp->sk1u pointer are protected
by rtnl_lock. so, rtnl_lock() is added.
Test command:
gtp-link add gtp1 &
killall gtp-link
ip link del gtp1
Splat looks like:
[ 83.182767] BUG: KASAN: use-after-free in __lock_acquire+0x3a20/0x46a0
[ 83.184128] Read of size 8 at addr ffff8880cc7d5360 by task ip/1008
[ 83.185567] CPU: 1 PID: 1008 Comm: ip Not tainted 5.2.0-rc6+ #50
[ 83.188469] Call Trace:
[ ... ]
[ 83.200126] lock_acquire+0x141/0x380
[ 83.200575] ? lock_sock_nested+0x3a/0xf0
[ 83.201069] _raw_spin_lock_bh+0x38/0x70
[ 83.201551] ? lock_sock_nested+0x3a/0xf0
[ 83.202044] lock_sock_nested+0x3a/0xf0
[ 83.202520] gtp_encap_destroy+0x18/0xe0 [gtp]
[ 83.203065] gtp_encap_disable.isra.14+0x13/0x50 [gtp]
[ 83.203687] gtp_dellink+0x56/0x170 [gtp]
[ 83.204190] rtnl_delete_link+0xb4/0x100
[ ... ]
[ 83.236513] Allocated by task 976:
[ 83.236925] save_stack+0x19/0x80
[ 83.237332] __kasan_kmalloc.constprop.3+0xa0/0xd0
[ 83.237894] kmem_cache_alloc+0xd8/0x280
[ 83.238360] sk_prot_alloc.isra.42+0x50/0x200
[ 83.238874] sk_alloc+0x32/0x940
[ 83.239264] inet_create+0x283/0xc20
[ 83.239684] __sock_create+0x2dd/0x540
[ 83.240136] __sys_socket+0xca/0x1a0
[ 83.240550] __x64_sys_socket+0x6f/0xb0
[ 83.240998] do_syscall_64+0x9c/0x450
[ 83.241466] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 83.242061]
[ 83.242249] Freed by task 0:
[ 83.242616] save_stack+0x19/0x80
[ 83.243013] __kasan_slab_free+0x111/0x150
[ 83.243498] kmem_cache_free+0x89/0x250
[ 83.244444] __sk_destruct+0x38f/0x5a0
[ 83.245366] rcu_core+0x7e9/0x1c20
[ 83.245766] __do_softirq+0x213/0x8fa
Fixes: 1e3a3abd8b ("gtp: make GTP sockets in gtp_newlink optional")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver allow to use devices with disabled iCPU only.
Some devices have pre-initialised iCPU by bootloader.
That state make switch unmanaged. This patch force reset
if device is in unmanaged state. In the result chip lost
internal firmware from RAM and it can be managed.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add platform part of vsc73xx driver.
It allows to use chip connected to a parallel memory bus and work in
memory-mapped I/O mode. (aka PI bus in chip manual)
By default device is working in big endian mode.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver (currently) only takes control of the switch chip over
SPI and configures it to route packages around when connected to a
CPU port. But Vitesse chip support also parallel interface.
This patch split driver into two parts: core and spi. It is required
for add support to another managing interface.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch syncs the name of few chip versions with the latest vendor
driver version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second, and last, set of patches for 5.3.
Major changes:
mt76
* use NAPI polling for tx cleanup on mt7603/mt7615
* add support for toggling edcca on mt7603
* fix rate control / tx status reporting issues on mt76x02/mt7603
* add support for eeprom calibration data from mtd on mt7615
* support configuring tx power on mt7615
* per-chain signal reporting on mt7615
iwlwifi
* Update the FW API for Channel State Information (CSI)
* Special Specific Absorption Rate (SAR) implementation for South Korea
ath10k
* fixes for SDIO support
* add support for firmware logging via WMI
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdIEMUAAoJEG4XJFUm622bYLsIAI7SOgbSvyuxi/SRk6PXZ5KI
WVqoQ0Jzt61C7gr2324lbExbQA4OoHaJfusyzIUwWifP55W83iYGHgLCXUKnBvng
/LehHN6satVBC0JMReLmuVE7Ac+4aPdFw9WbS4QneZwLr90CzjXgPebiKchFOI5V
1PwPfN0nG/NKJac2vv6/Y8gERyj5i4ZvYipGMQCiKRHFrb7FRRhxwI3uG1BkeR1r
i7QjUiQXG5RmeXd2QWJg/MkwZY5XKNqYxZyXUhBRy8kUH75poAEJ8ll3KIrAvJ87
0r3YnDlhyxseShYDzcKt1bgVcqEkJVGhHPaadq2nkmys5NKoKiuTYD1Jj7089jQ=
=OVjU
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.3
Second, and last, set of patches for 5.3.
Major changes:
mt76
* use NAPI polling for tx cleanup on mt7603/mt7615
* add support for toggling edcca on mt7603
* fix rate control / tx status reporting issues on mt76x02/mt7603
* add support for eeprom calibration data from mtd on mt7615
* support configuring tx power on mt7615
* per-chain signal reporting on mt7615
iwlwifi
* Update the FW API for Channel State Information (CSI)
* Special Specific Absorption Rate (SAR) implementation for South Korea
ath10k
* fixes for SDIO support
* add support for firmware logging via WMI
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for transmit side kernel-TLS acceleration.
Offload the crypto encryption to HW.
Per TLS connection:
- Use a separate TIS to maintain the HW context.
- Use a separate encryption key.
- Maintain static and progress HW contexts by posting the proper
WQEs at creation time, or upon resync.
- Use a special DUMP opcode to replay the previous frags and sync
the HW context.
To make sure the SQ is able to serve an xmit request, increase
SQ stop room to cover:
- static params WQE,
- progress params WQE, and
- resync DUMP per frag.
Currently supporting TLS 1.2, and key size 128bit.
Tested over SimX simulator.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the existing mlx5e_post_nop(), but marks a fence
in the WQE control segment.
Added as a separate new function to not hurt the performance
of the common case.
To be used in a downstream patch of the series.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the EN TIS creation function (mlx5e_create_tis) be responsible
for applying common mdev related fields.
Other specific fields must be set by the caller and passed within
the inbox.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use an SQ field for stop_room, and use the larger value only if TLS
is supported.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When polling a CQE of an SKB-less WQE, don't assume it consumed only
one WQEBB. Use wi->num_wqebbs directly instead.
In the downstream patch, SKB-less WQEs might have more the one WQEBB,
thus this change is needed.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change mlx5e_sq_fetch_wqe to be agnostic to the Work Queue
Element (WQE) type.
Before this patch, it was specific for struct mlx5e_tx_wqe.
In order to allow the change, the function now returns the
generic void pointer, and gets the WQE size to do the zero
memset.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ctrl->tisn field exists, this indicates an operation (HW offload)
on the TCP payload.
For such WQEs, inline the headers up to L4.
This is in preparation for kTLS HW offload support, added in
a downstream patch.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take datapath helper functions to a new header file en/txrx.h.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the new TLS implementation of the Connect-X family.
Introduce a new compilation flag MLX5_TLS for it.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Encryption key create / destroy is done via
CREATE_GENERAL_OBJECT / DESTROY_GENERAL_OBJECT commands.
To be used in downstream patches by TLS API wrappers, to configure
the TIS context with the encryption key.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always contain all acceleration functions declarations in
'accel' files, independent to the flags setting.
For this, introduce new flags CONFIG_FPGA_{IPSEC/TLS} and use stubs
where needed.
This obsoletes the need for stubs in 'fpga' files. Remove them.
Also use the new flags in Makefile, to decide whether to compile
TLS-specific or IPSEC-specific objects, or not.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not directly call fpga version of IPsec function from main.c.
Wrap it by an accel version, and call the wrapper.
This will allow deprecating the FPGA IPsec stubs in downstream
patch.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series adds mlx5 support for devlink fw versions query.
1) Implement the required low level firmware commands
2) Implement the devlink knobs and callbacks for fw versions query.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl0eZOQACgkQSD+KveBX
+j6a0gf/SbSY2yDz6iyDZy7Zt0e7onD395UyWIoXbXJAI/aMggvdNE233dh369xa
d4Zo8zvFijiFpPKmP0p+WZfvR5YPPWgtOYDv1MbaTz5lqsGYUh2kN9FaTyCNZW3O
jeNidxjsne70VBrpmOZJX2mxduKwRdxchRg2iQPdeZQGO5Uq3nEdOfJVx/mhsIGw
iRczF4IAQpArZEyKXgqMSrtJ99FJ7JSJXnsqjVJyUC1zyCZ+Cq3VV55+u5VCBokd
qr/VSYqFd38SEHR5l4nXDXLX23pOwWNhUdPgGopjak8bN3k19vk6GfQ2bzLFnaOW
4fx1k4uTixKOrbLkgzay/YSsoF2TDw==
=Bwl7
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-07-04-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-update-2019-07-04
This series adds mlx5 support for devlink fw versions query.
1) Implement the required low level firmware commands
2) Implement the devlink knobs and callbacks for fw versions query.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For spinlocks the type spinlock_t should be used instead of "struct
spinlock".
Use spinlock_t for spinlock's definition.
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: oss-drivers@netronome.com
Cc: netdev@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting Arnd,
We have to do a sync_single_for_device /somewhere/ before the
buffer is given to the device. On a non-cache-coherent machine with
a write-back cache, there may be dirty cache lines that get written back
after the device DMA's data into it (e.g. from a previous memset
from before the buffer got freed), so you absolutely need to flush any
dirty cache lines on it first.
Since the coherency is configurable in this device make sure we cover
all configurations by explicitly syncing the allocated buffer for the
device before refilling it's descriptors
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If HCLGE_MBX_MAX_RESP_DATA_SIZE > HCLGE_MBX_MAX_RESP_DATA_SIZE,
the memcpy will cause out of memory. So this patch just set
resp_data_len to the maximum length for this case.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some bitwise operator used signed type, this patch fixes
them with unsigned type.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds default value for tc_size and tc_offset, or it may
get random value and used later.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of msg_data may be NULL in some cases, which will cause
errors reported by some compiler.
So this patch adds a check to fix it.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of param type is always not changed in
hclgevf_bind_ring_to_vector, move the assignment to
front of "for {}" can reduce the redundant assignment.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the HNS3 driver just defines part of IMP return code,
This patch supplements all the remaining IMP return code, and adds
a function to convert this code to the error number.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver queries the media port information, and
updates the port capability periodically. But it sets an error
mac->speed_type value, which stops update port capability.
Fixes: 88d10bd6f7 ("net: hns3: add support for multiple media type")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control autoneg is unsupported for fibre port. It takes no
effect for flow control when restart autoneg. This patch fixes
it, return -EOPNOTSUPP when user tries to enable flow control
autoneg.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x20, the broadcast promisc is enabled by firmware,
it's unnecessary to enable it when initializing VF.
For revision 0x21, it's necessary to enable broadcast promisc mode
when initializing or re-initializing VF, otherwise, it will be
unable to send and receive promisc packets.
Fixes: f01f5559ca ("net: hns3: don't allow vf to enable promisc mode")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the flag of RTL8152_UNPLUG if and only if the device is unplugged.
Some error codes sometimes don't mean the real disconnection of usb device.
For those situations, set the flag of RTL8152_UNPLUG causes the driver skips
some flows of disabling the device, and it let the device stay at incorrect
state.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply by filling the PTP shaper parameters array.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When getting port up down event (PUDE), change the PTP shaper
configuration based on hardware time stamping on/off and the port's
speed.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to get more accurate hardware time stamping, the driver needs to
enable PTP shaper on the port, for speeds lower than 40 Gbps.
Enable the PTP shaper on the port when the user turns on the hardware
time stamping, and disable it when the user turns off the hardware time
stamping.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New operation for getting the port's speed as part of port-type-speed
operations.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the PTP shaper parameters during the ptp_init(). For different
speeds, there are different parameters.
When the port's speed changes and PTP shaper is enabled, the firmware
changes the ETS shaper values according to the PTP shaper parameters for
this new speed.
The PTP shaper parameters array is left empty for now, will be filled in
a follow-up patch.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QPSC allows advanced configuration of the PTP shapers.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add note about disabling the PTP shaper when calling to
mlxsw_sp_port_ets_maxrate_set().
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP Shaper field is used for enabling and disabling of port-rate based
shaper which is slightly lower than port rate.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/socionext/netsec.c: In function 'netsec_clean_tx_dring':
drivers/net/ethernet/socionext/netsec.c:637:15: warning:
variable 'pkts' set but not used [-Wunused-but-set-variable]
It is not used since commit ba2b232108 ("net: netsec: add XDP support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded memset as alloc_etherdev is using kvzalloc which uses
__GFP_ZERO flag
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several drivers cast a struct device pointer to a struct
platform_device pointer only to then call platform_get_drvdata().
To improve readability, these constructs can be simplified
by using dev_get_drvdata() directly.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several drivers cast a struct device pointer to a struct
platform_device pointer only to then call platform_get_drvdata().
To improve readability, these constructs can be simplified
by using dev_get_drvdata() directly.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback is invoked using 'devlink dev info <pci>' command and returns
the running and pending firmware version of the HCA and the name of the
kernel driver.
If there is a pending firmware version (a new version is burned but the
HCA still runs with the previous) it is returned as the stored
firmware version. Otherwise, the running version is returned for this
field.
Output example:
$ devlink dev info pci/0000:00:06.0
pci/0000:00:06.0:
driver mlx5_core
versions:
fixed:
fw.psid MT_0000000009
running:
fw.version 16.26.0100
stored:
fw.version 16.26.0100
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Using the MCQI and MCQS registers, we query the running and pending
fw version of the HCA.
The MCQS is queried with sequentially increasing component index, until
a component of type BOOT_IMG is found. Querying this component's version
using the MCQI register yields the running and pending fw version of the
HCA.
Querying MCQI for the pending fw version should be done only after
validating that such fw version exists. This is done my checking
'component update state' field in MCQS output.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Misc updates from mlx5-next branch:
1) Add the required HW definitions and structures for upcoming TLS
support.
2) Add support for MCQI and MCQS hardware registers for fw version query.
3) Added hardware bits and structures definitions for sub-functions
4) Small code cleanup and improvement for PF pci driver.
5) Bluefield (ECPF) updates and refactoring for better E-Switch
management on ECPF embedded CPU NIC:
5.1) Consolidate querying eswitch number of VFs
5.2) Register event handler at the correct E-Switch init stage
5.3) Setup PF's inline mode and vlan pop when the ECPF is the
E-Swtich manager ( the host PF is basically a VF ).
5.4) Handle Vport UC address changes in switchdev mode.
6) Cleanup the rep and netdev reference when unloading IB rep.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
i# All conflicts fixed but you are still merging.
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-07-03
The following pull-request contains BPF updates for your *net-next* tree.
There is a minor merge conflict in mlx5 due to 8960b38932 ("linux/dim:
Rename externally used net_dim members") which has been pulled into your
tree in the meantime, but resolution seems not that bad ... getting current
bpf-next out now before there's coming more on mlx5. ;) I'm Cc'ing Saeed
just so he's aware of the resolution below:
** First conflict in drivers/net/ethernet/mellanox/mlx5/core/en_main.c:
<<<<<<< HEAD
static int mlx5e_open_cq(struct mlx5e_channel *c,
struct dim_cq_moder moder,
struct mlx5e_cq_param *param,
struct mlx5e_cq *cq)
=======
int mlx5e_open_cq(struct mlx5e_channel *c, struct net_dim_cq_moder moder,
struct mlx5e_cq_param *param, struct mlx5e_cq *cq)
>>>>>>> e5a3e259ef
Resolution is to take the second chunk and rename net_dim_cq_moder into
dim_cq_moder. Also the signature for mlx5e_open_cq() in ...
drivers/net/ethernet/mellanox/mlx5/core/en.h +977
... and in mlx5e_open_xsk() ...
drivers/net/ethernet/mellanox/mlx5/core/en/xsk/setup.c +64
... needs the same rename from net_dim_cq_moder into dim_cq_moder.
** Second conflict in drivers/net/ethernet/mellanox/mlx5/core/en_main.c:
<<<<<<< HEAD
int cpu = cpumask_first(mlx5_comp_irq_get_affinity_mask(priv->mdev, ix));
struct dim_cq_moder icocq_moder = {0, 0};
struct net_device *netdev = priv->netdev;
struct mlx5e_channel *c;
unsigned int irq;
=======
struct net_dim_cq_moder icocq_moder = {0, 0};
>>>>>>> e5a3e259ef
Take the second chunk and rename net_dim_cq_moder into dim_cq_moder
as well.
Let me know if you run into any issues. Anyway, the main changes are:
1) Long-awaited AF_XDP support for mlx5e driver, from Maxim.
2) Addition of two new per-cgroup BPF hooks for getsockopt and
setsockopt along with a new sockopt program type which allows more
fine-grained pass/reject settings for containers. Also add a sock_ops
callback that can be selectively enabled on a per-socket basis and is
executed for every RTT to help tracking TCP statistics, both features
from Stanislav.
3) Follow-up fix from loops in precision tracking which was not propagating
precision marks and as a result verifier assumed that some branches were
not taken and therefore wrongly removed as dead code, from Alexei.
4) Fix BPF cgroup release synchronization race which could lead to a
double-free if a leaf's cgroup_bpf object is released and a new BPF
program is attached to the one of ancestor cgroups in parallel, from Roman.
5) Support for bulking XDP_TX on veth devices which improves performance
in some cases by around 9%, from Toshiaki.
6) Allow for lookups into BPF devmap and improve feedback when calling into
bpf_redirect_map() as lookup is now performed right away in the helper
itself, from Toke.
7) Add support for fq's Earliest Departure Time to the Host Bandwidth
Manager (HBM) sample BPF program, from Lawrence.
8) Various cleanups and minor fixes all over the place from many others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Both MTK_TRGMII_MT7621_CLK and MTK_PATH_BIT are defined as bit 10.
This can causes issues on non-MT7621 devices which has the
MTK_PATH_BIT(MTK_ETH_PATH_GMAC1_RGMII) and MTK_TRGMII capability set.
The wrong TRGMII setup code can be executed. The current wrongly executed
code doesn’t do any harm on MT7623 and the TRGMII setup for the MT7623
SOC side is done in MT7530 driver So it wasn’t noticed in the test.
Move all capability bits in one enum so that they are all unique and easy
to expand in the future.
Because mtk_eth_path enum is merged in to mkt_eth_capabilities, the
variable path value is no longer between 0 to number of paths,
mtk_eth_path_name can’t be used anymore in this form. Convert the
mtk_eth_path_name array to a function to lookup the pathname.
The old code walked thru the mtk_eth_path enum, which is also merged
with mkt_eth_capabilities. Expand array mtk_eth_muxc so it can store the
name and capability bit of the mux. Convert the code so it can walk thru
the mtk_eth_muxc array.
Fixes: 8efaa653a8 ("net: ethernet: mediatek: Add MT7621 TRGMII mode support")
Signed-off-by: René van Dorst <opensource@vdorst.com>
v1->v2:
- Move all capability bits in one enum, suggested by Willem de Bruijn
- Convert the mtk_eth_path_name array to a function to lookup the pathname
- Expand array mtk_eth_muxc so it can also store the name and capability
bit of the mux
- Updated commit message
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable GMAC v4.xx and beyond to support 16KiB buffer.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, gratuitous ARP/ND packets are sent every `miimon'
milliseconds. This commit allows a user to specify a custom delay
through a new option, `peer_notif_delay'.
Like for `updelay' and `downdelay', this delay should be a multiple of
`miimon' to avoid managing an additional work queue. The configuration
logic is copied from `updelay' and `downdelay'. However, the default
value cannot be set using a module parameter: Netlink or sysfs should
be used to configure this feature.
When setting `miimon' to 100 and `peer_notif_delay' to 500, we can
observe the 500 ms delay is respected:
20:30:19.354693 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:19.874892 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:20.394919 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:20.914963 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
In bond_mii_monitor(), I have tried to keep the lock logic readable.
The change is due to the fact we cannot rely on a notification to
lower the value of `bond->send_peer_notif' as `NETDEV_NOTIFY_PEERS' is
only triggered once every N times, while we need to decrement the
counter each time.
iproute2 also needs to be updated to be able to specify this new
attribute through `ip link'.
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable err is being assigned with a value that is never
read and it is being updated in the next statement with a new value.
The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the check to see if a page is allocated is incorrect
and is checking if the pointer page is null, not *page as
intended. Fix this.
Addresses-Coverity: ("Dereference before null check")
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_xmit_roundrobin() checks for IGMP packets but it parses
the IP header even before checking skb->protocol.
We should validate the IP header with pskb_may_pull() before
using iph->protocol.
Reported-and-tested-by: syzbot+e5be16aa39ad6e755391@syzkaller.appspotmail.com
Fixes: a2fd940f4c ("bonding: fix broken multicast with round-robin mode")
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions change event output data size changes when functions other
than VFs will be enabled in HCA CAP.
With current API, multiple callers needs to align, calculate accurate
size of the output data depending on number on non VF functions enabled
in the device.
Instead of duplicating such math at multiple places, refactor
mlx5_esw_query_functions() to return raw output allocated by itself.
Caller must free the allocated memory using kvfree() as described in the
function comment section.
This hides calcuation within mlx5_esw_query_functions() and provides
simpler API.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eswitch function change handler will service multiple type of events for
VFs and non VF functions update.
Hence, introduce and use the helper function
esw_vfs_changed_event_handler() for handling change in num VFs to improve
the code readability.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Instead MLX5_TOTAL_VPORTS, use mlx5_eswitch_get_total_vports().
mlx5_eswitch_get_total_vports() in subsequent patch accounts for SF
vports as well.
Expanding MLX5_TOTAL_VPORTS macro would require exposing SF internals to
more generic vport.h header file. Such exposure is not desired.
Hence a mlx5_eswitch_get_total_vports() is introduced.
Given that mlx5_eswitch_get_total_vports() API wants to work on const
mlx5_core_dev*, change its helper functions also to accept const *dev.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The hip07 chip support vlan TSO, this patch adds NETIF_F_TSO
and NETIF_F_TSO6 flags to vlan_features to improve the
performance after adding vlan to the net ports.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable err is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable tpd_req is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8153b_rx_agg_chg_indicate() needs to be called after enabling TX/RX and
before calling rxdy_gated_en(tp, false). Otherwise, the change of the
settings of RX aggregation wouldn't work.
Besides, adjust rtl8152_set_coalesce() for the same reason. If
rx_coalesce_usecs is changed, restart TX/RX to let the setting work.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver changes to detect/timestamp the unicast PTP packets.
Changes from previous version:
-------------------------------
v2: Defined a macro for unicast ptp param mask.
Please consider applying this to "net-next".
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
u64_stats_fetch_begin needs to initialize start.
Signed-off-by: Catherine Sullivan <csully@google.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report EQE data upon CQ completion to let upper layers use this data.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Report a CQ error event only when a handler was set.
This enables mlx5_ib to not set a handler upon CQ creation and use some
other mechanism to get this event as of other events by the
mlx5_eq_notifier_register API.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Enhance mlx5_core_create_cq() to get the command out buffer from the
callers to let them use the output.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Expose the API to register for ANY event, mlx5_ib will be able to use
this functionality for its needs.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Use the reported device capabilities for the supported user events (i.e.
affiliated and un-affiliated) to set the EQ mask.
As the event mask can be up to 256 defined by 4 entries of u64 change
the applicable code to work accordingly.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
The firmware command to destroy a CQ might fail when the object is
referenced by other object and the ref count is managed by the firmware.
To enable a second successful destruction post the first failure need to
change mlx5_eq_del_cq() to be a void function.
As an error in mlx5_eq_del_cq() is quite fatal from the option to
recover, a debug message inside it should be good enougth and it was
changed to be void.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Before mlxsw_sp1_ptp_packet_finish() sends the packet back, it validates
whether the corresponding port is still valid. However the condition is
incorrect: when mlxsw_sp_port == NULL, the code dereferences the port to
compare it to skb->dev.
The condition needs to check whether the port is present and skb->dev still
refers to that port (or else is NULL). If that does not hold, bail out.
Add a pair of parentheses to fix the condition.
Fixes: d92e4e6e33 ("mlxsw: spectrum: PTP: Support timestamping on Spectrum-1")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that the GPD MicroPC is broken in a way that no valid
MAC address can be read from the network chip. The vendor driver deals
with this by assigning a random MAC address as fallback. So let's do
the same.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 759d095741.
The patch was based on a misunderstanding. As Al Viro pointed out [0]
it's simply wrong on big endian. So let's revert it.
[0] https://marc.info/?t=156200975600004&r=1&w=2
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 760f1dc295 ("net: stmmac: add sanity check to
device_property_read_u32_array call") introduced error checking of the
device_property_read_u32_array() call in stmmac_mdio_reset().
This results in the following error when the "snps,reset-delays-us"
property is not defined in devicetree:
invalid property snps,reset-delays-us
This sanity check made sense until commit 84ce4d0f9f ("net: stmmac:
initialize the reset delay array") ensured that there are fallback
values for the reset delay if the "snps,reset-delays-us" property is
absent. That was at the cost of making that property mandatory though.
Drop the sanity check for device_property_read_u32_array() and thus make
the "snps,reset-delays-us" property optional again (avoiding the error
message while loading the stmmac driver with a .dtb where the property
is absent).
Fixes: 760f1dc295 ("net: stmmac: add sanity check to device_property_read_u32_array call")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix use-after-free of skb when rx_handler returns RX_HANDLER_PASS.
Signed-off-by: Andreas Steinmetz <ast@domdv.de>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No reason to error out on a MT7621 device with DDR2 memory when non
TRGMII mode is selected.
Only MT7621 DDR2 clock setup is not supported for TRGMII mode.
But non TRGMII mode doesn't need any special clock setup.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes standard netdev stats in ethtool -S.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We support many speeds and it doesn't make much sense to list them all
in the Kconfig. Let's just call it Multi-Gigabit.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the following ethtool commands:
ethtool -s|--change devname [msglvl N] [msglevel type on|off]
ethtool -S|--statistics devname
ethtool -i|--driver devname
ethtool -l|--show-channels devname
ethtool -L|--set-channels devname
ethtool -g|--show-ring devname
ethtool --reset devname
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the workqueue to handle management interrupts and
support for resets.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for passing traffic.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver framework for the Compute Engine Virtual NIC that will be
available in the future.
At this point the only functionality is loading the driver.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a blackhole net device that can be used for "dead"
dst entries instead of loopback device. This blackhole device differs
from loopback in few aspects: (a) It's not per-ns. (b) MTU on this
device is ETH_MIN_MTU (c) The xmit function is essentially kfree_skb().
and (d) since it's not registered it won't have ifindex.
Lower MTU effectively make the device not pass the MTU check during
the route check when a dst associated with the skb is dead.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Rename r8153b_queue_wake() to r8153_queue_wake().
2. Correct the setting. The enable bit should be 0xd38c bit 0. Besides,
the 0xd38a bit 0 and 0xd398 bit 8 have to be cleared for both enabled
and disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded memset as alloc_etherdev is using kvzalloc which uses
__GFP_ZERO flag
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interface only supports 1 Tx queue so locking is introduced on
the Tx queue if XDP is enabled to make sure .ndo_start_xmit and
.ndo_xdp_xmit won't corrupt Tx ring
- Performance (SMMU off)
Benchmark XDP_SKB XDP_DRV
xdp1 291kpps 344kpps
rxdrop 282kpps 342kpps
- Performance (SMMU on)
Benchmark XDP_SKB XDP_DRV
xdp1 167kpps 324kpps
rxdrop 164kpps 323kpps
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use page_pool and it's DMA mapping capabilities for Rx buffers instead
of netdev/napi_alloc_frag()
Although this will result in a slight performance penalty on small sized
packets (~10%) the use of the API will allow to easily add XDP support.
The penalty won't be visible in network testing i.e ipef/netperf etc, it
only happens during raw packet drops.
Furthermore we intend to add recycling capabilities on the API
in the future. Once the recycling is added the performance penalty will
go away.
The only 'real' penalty is the slightly increased memory usage, since we
now allocate a page per packet instead of the amount of bytes we need +
skb metadata (difference is roughly 2kb per packet).
With a minimum of 4BG of RAM on the only SoC that has this NIC the
extra memory usage is negligible (a bit more on 64K pages)
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly, other callers of idr_get_next_ul() suffer the same
overflow bug as they don't handle it properly either.
Introduce idr_for_each_entry_continue_ul() to help these callers
iterate from a given ID.
cls_flower needs more care here because it still has overflow when
does arg->cookie++, we have to fold its nested loops into one
and remove the arg->cookie++.
Fixes: 01683a1469 ("net: sched: refactor flower walk to iterate over idr")
Fixes: 12d6066c3b ("net/mlx5: Add flow counters idr")
Reported-by: Li Shuang <shuali@redhat.com>
Cc: Davide Caratti <dcaratti@redhat.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Chris Mi <chrism@mellanox.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The get_ts_info callback is used for obtaining information about
timestamping capabilities of a network device. On Spectrum-1, implement
it to advertise the PHC and the capability to do HW timestamping, and
the supported RX and TX filters.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SIOCSHWTSTAMP ioctl configures HW timestamping on a given port.
Dispatch the ioctls to per-chip handler (which add to ptp_ops). Find
which PTP messages need to be timestamped and configure MTPPPC
accordingly.
The SIOCGHWTSTAMP ioctl is getter for the current configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure MTPTPT to set which message types should arrive under which
PTP trap, and MOGCR to clear the timestamp queue after its contents are
reported through PTP_ING_FIFO or PTP_EGR_FIFO.
With this configuration, PTP packets start arriving through the PTP
traps. However since timestamping is disabled by default and there is
currently no way to enable it, they will not be timestamped.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Spectrum-1, timestamped PTP packets and the corresponding timestamps
need to be kept in caches until both are available, at which point they are
matched up and packets forwarded as appropriate. However, not all packets
will ever see their timestamp, and not all timestamps will ever see their
packet. It is therefore necessary to dispose of such abandoned entries.
To that end, introduce a garbage collector to collect entries that have
not had their counterpart turn up within about a second. The GC
maintains a monotonously-increasing value of GC cycle. Every entry that
is put to the hash table is annotated with the GC cycle at which it
should be collected. When the GC runs, it walks the hash table, and
collects the objects according to their GC cycle annotation.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Spectrum-1, timestamps arrive through a pair of dedicated events:
MLXSW_TRAP_ID_PTP_ING_FIFO and _EGR_FIFO. The payload delivered with
those traps is contents of the timestamp FIFO at a given port in a given
direction. Add a Spectrum-1-specific handler for these two events which
decodes the timestamps and forwards them to the PTP module.
Add a function that parses a packet, dispatching to ptp_classify_raw(),
and decodes PTP message type, domain number, and sequence ID. Add a new
mlxsw dependency on the PTP classifier.
Add helpers that can store and retrieve unmatched timestamps and SKBs to
the hash table added in a preceding patch.
Add the matching code itself: upon arrival of a timestamp or a packet,
look up the corresponding unmatched entry, and match it up. If there is
none, add a new unmatched entry. This logic is the same on ingress as on
egress.
Packets and timestamps that never matched need to be eventually disposed
of. A garbage collector added in a follow-up patch will take care of
that. Since currently all this code is turned off, no crud will
accumulate in the hash table.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, the PTP hardware clock code was only invoked in the process
context (SYS_clock_adjtime -> do_clock_adjtime -> k_clock::clock_adj ->
pc_clock_adjtime -> posix_clock_operations::clock_adjtime ->
ptp_clock_info::adjtime -> mlxsw_spectrum).
In order to enable HW timestamping, which is tied into trap handling, it
will be necessary to take the clock lock from the PCI queue handler
tasklets as well.
Therefore use the _bh variants when handling the clock lock. Incidentally,
Documentation/ptp/ptp.txt recommends _irqsave variants, but that's
unnecessarily strong for our needs.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two ptp_ops: init and fini, to initialize and finalize the PTP
subsystem. Call as appropriate from mlxsw_sp_init() and _fini().
Lay the groundwork for Spectrum-1 support. On Spectrum-1, the received
timestamped packets and their corresponding timestamps arrive
independently, and need to be matched up. Introduce the related data types
and add to struct mlxsw_sp_ptp_state the hash table that will keep the
unmatched entries.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Spectrum-1, timestamps are delivered separately from the packets, and
need to paired up. Therefore, at some point after mlxsw_sp_port_xmit()
is invoked, it is necessary to involve the chip-specific driver code to
allow it to do the necessary bookkeeping and matching.
On Spectrum-2, timestamps are delivered in CQE. For that reason,
position the point of driver involvement into mlxsw_pci_cqe_sdq_handle()
to make it hopefully easier to extend for Spectrum-2 in the future.
To tell the driver what port the packet was sent on, keep tx_info
in SKB control buffer.
Introduce a new driver core interface mlxsw_core_ptp_transmitted(), a
driver callback ptp_transmitted, and a PTP op transmitted. The callee is
responsible for taking care of releasing the SKB passed to the new
interfaces, and correspondingly have the new stub callbacks just call
dev_kfree_skb_any().
Follow-up patches will introduce the actual content into
mlxsw_sp1_ptp_transmitted() in particular.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SKB control buffer is useful (and used) for bookkeeping of information
related to that SKB. Add helpers so that the mlxsw driver(s) can safely use
the buffer as well. The structure is currently empty, individual users will
add members to it as necessary.
Note that SKB allocation functions already clear the buffer, so the cleanup
is only necessary when ndo_start_xmit is called.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configured, the Spectrum hardware can recognize PTP packets and
trap them to the CPU using dedicated traps, PTP0 and PTP1.
One reason to get PTP packets under dedicated traps is to have a
separate policer suitable for the amount of PTP traffic expected when
switch is operated as a boundary clock. For this, add two new trap
groups, MLXSW_REG_HTGT_TRAP_GROUP_SP_PTP0 and _PTP1, and associate the
two PTP traps with these two groups.
In the driver, specifically for Spectrum-1, event PTP packets will need
to be paired up with their timestamps. Those arrive through a different
set of traps, added later in the patch set. To support this future use,
introduce a new PTP op, ptp_receive.
It is possible to configure which PTP messages should be trapped under
which PTP trap. On Spectrum systems, we will use PTP0 for event
packets (which need timestamping), and PTP1 for control packets (which
do not). Thus configure PTP0 trap with a custom callback that defers to
the ptp_receive op.
Additionally, L2 PTP packets are actually trapped through the LLDP trap,
not through any of the PTP traps. So treat the LLDP trap the same way as
the PTP0 trap. Unlike PTP traps, which are currently still disabled,
LLDP trap is active. Correspondingly, have all the implementations of
the ptp_receive op return true, which the handler treats as a signal to
forward the packet immediately.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Spectrum-1, timestamps for PTP packets are delivered through queues
of ingress and egress timestamps. There are two event traps
corresponding to activity on each of those queues. This mechanism is
absent on Spectrum-2, and therefore the traps should only be registered
on Spectrum-1.
Carry a chip-specific listener array in mlxsw_sp->listeners and
listeners_count. Register listeners from that array in
mlxsw_sp_traps_init(). Add a new listener array for Spectrum-1 traps and
configure the newly-added mlxsw_sp->listeners with this array.
The listener array is empty for now, the events will be added in a later
patch.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Spectrum-1, timestamps for PTP packets are delivered through queues
of ingress and egress timestamps. There are two event traps
corresponding to activity on each of those queues. This mechanism is
absent on Spectrum-2, and therefore the traps should only be registered
on Spectrum-1.
Extract out of mlxsw_sp_traps_init() a generic helper,
mlxsw_sp_traps_register(), and likewise with _unregister(). The new helpers
will later be called with Spectrum-1-specific traps.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register serves to configure global parameters of certain
monitoring operations. The following patches will use it to configure
that when PTP timestamps are delivered through the PTP FIFO traps, the
FIFO in question is cleared as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTPPTR is used for reading the per port PTP timestamp FIFO.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is used for configuring under which trap to deliver PTP
packets depending on type of the packet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register serves for configuration of which PTP messages should be
timestamped. This is a global configuration, despite the register name.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NVME device emulation mode is enabled, more than one PFs use the
same physical port. In this case, MPFS is required to program L2
addresses.
It used to rely on netdev set_rx_mode in switchdev mode, but driver
later changed to not create netdev for eswitch manager once in
switchdev mode. So, UC address event should be handled.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When ECPF is the eswitch manager, host PF is treated like other VFs.
Driver should do the same for inline mode and vlan pop.
Add new iterators to include host PF if ECPF is the eswitch manager.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use the defined iterators to traversal VF reps/vport. Also, rely on
num of VFs rather than the counter of enabled vports as PF will also
be enabled from ECPF side, and the counter will be different from
num of VFs.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When driver is doing eswitch mode change, it's critical to keep number
of enabled VFs unchanged. However, it can be changed on the fly once
function changed event is registered.
To remove this uncertainty, function changed event should not be
registered before all setups, and first be unregistered before all
cleanups. Wrap this functionality together with vport event handler.
Fixes: 61fc880839e6 ("net/mlx5: E-Switch, Handle representors creation in handler context")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Enabled number of VFs is key for eswich manager to do flow steering
initialization and vport configurations. However, the number of
enabled VFs may come from two sources as below.
PF: num of VFs is provided by enabled SR-IOV of itself.
ECPF: num of VFs is provided by enabled SR-IOV from its peer PF. And
SR-IOV can't be enabled from ECPF itself.
Current driver handles the two cases in different stages and passing
the number of enabled VFs among a large scope of internal functions.
It is usually hard to find out where is the real number of VFs from
due to layers of argument pass-in.
This patch consolidated that number from the entry point of doing
eswitch setup, and maintained a copy so that eswitch functions can
refer to it directly.
Eswitch driver shall always use this number when referring to enabled
number of VFs, don't use other numbers such as from SR-IOV.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Devlink eswitch mode is not necessarily related to SR-IOV, e.g, ECPF
can be at offload mode when SR-IOV is not enabled.
Rename the interface and eswitch mode names to decouple from SR-IOV,
and cleanup eswitch messages accordingly.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When ECPF is eswitch manager, it has the privilege to query and
configure the mac and node guid of host PF.
While vport number of host PF is 0, the vport command should be
issued with other_vport set in this case as the cmd is issued by
ECPF vport(0xfffe).
Add a specific function to query own vport mac. Low level functions
are used by vport manager to query/modify any vport mac and node guid.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Before the offending commit, vlan will be configured if either vlan
or qos is set. After the change with new set flags, function callers
should provide flags accordingly.
Fixes: e33dfe316c ("net/mlx5: E-Switch, Allow fine tuning of eswitch vport push/pop vlan")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
While enabling SR-IOV, PCI core already checks that if SR-IOV is already
enabled, it returns failure error code.
Hence, remove such duplicate check from mlx5_core driver.
While at it, make mlx5_device_disable_sriov() to perform cleanup of VFs in
reverse order of mlx5_device_enable_sriov().
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When ECPF eswitch manager is at offloads mode, it monitors functions
changed event from host PF side and acts according to the number of
VFs enabled/disabled.
As ECPF and host PF work in two independent hosts, it's possible that
host PF OS reboots but ECPF system is still kept on and continues
monitoring events from host PF. When kernel from host PF side is
booting, PCI iov driver does sriov_init and compute_max_vf_buses by
iterating over all valid num of VFs. This triggers FLR and generates
functions changed events, even though host PF HCA is not enabled at
this time. However, ECPF is not aware of this information, and still
handles these events as usual. ECPF system will see massive number of
reps are created, but destroyed immediately once creation finished.
To eliminate this noise, a bit is added to host parameter context to
indicate host PF is disabled. ECPF will not handle the VF changed
event if this bit is set.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As mlx5_get_next_phys_dev is used only for PCI PF devices use case,
limit it to search only for PCI devices.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5_pci_init() performs pci specific initialization of the
mlx5_core_dev struct.
Hence move pci_status_mutex to pci initialization routine
mlx5_pci_init().
This allows reusing mlx5_mdev_init() to non PCI devices.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In the single IB device mode, the mapping between vport number and
rep relies on a counter. However for dynamic vport allocation, it is
desired to keep consistent map of eswitch vport and IB port.
Hence, simplify code to remove the free running counter and instead
use the available vport index during load/unload sequence from the
eswitch.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Suggested-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Driver is referring to the array index when doing rep initialization,
using vport is confusing as it's normally interpreted as vport number.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This series adds some misc updates for mlx5e driver
1) Allow adding the same mac more than once in MPFS table
2) Move to HW checksumming advertising
3) Report netdevice MPLS features
4) Correct physical port name of the PF representor
5) Reduce stack usage in mlx5_eswitch_termtbl_create
6) Refresh TIR improvement for representors
7) Expose same physical switch_id for all representors
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl0WnOAACgkQSD+KveBX
+j6xQwgAuarc5NCi8jg9m+yXFXj/kr1cPwZ6Pxadi8hAd3NbEMGtutdFZIXsIXZZ
y0uYxzkrCqXUUh2ZnpE09YlBISLyVSt3WGdqgJn1wel//O33gS6GpYXwVGOfgL7n
+d9FCYvrun6v6aOHM5ZGxQ+qxHzupz5k4F0r7fz2Gsd+JEgL58nwc8ERSbOTbZMO
TLO1pcxlXWwGSqd5uc4AHi8hZTvuzWl/Fm5hOTP9gx/Sl3UaYWa3WiTgj5uOD5Zt
956Xqk0LLwSaiKVAsFjIa7HHWOaDLnVmbmTUzhv82hharqmvPW1CIWlx1gv01KoP
wMWoyyoy7cTyyrWNozWEed/14LyEVA==
=S4bJ
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2019-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2019-06-28
This series adds some misc updates for mlx5e driver
1) Allow adding the same mac more than once in MPFS table
2) Move to HW checksumming advertising
3) Report netdevice MPLS features
4) Correct physical port name of the PF representor
5) Reduce stack usage in mlx5_eswitch_termtbl_create
6) Refresh TIR improvement for representors
7) Expose same physical switch_id for all representors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-06-28
This series contains a smorgasbord of updates to many of the Intel
drivers.
Gustavo A. R. Silva updates the ice and iavf drivers to use the
strcut_size() helper where possible.
Miguel increases the pause and refresh time for flow control in the
e1000e driver during reset for certain devices.
Dann Frazier fixes a potential NULL pointer dereference in ixgbe driver
when using non-IPSec enabled devices.
Colin Ian King fixes a potential overflow during a shift in the ixgbe
driver. Also fixes a potential NULL pointer dereference in the iavf
driver by adding a check.
Venkatesh Srinivas converts the e1000 driver to use dma_wmb() instead of
wmb() for doorbell writes to avoid SFENCEs in the transmit and receive
paths.
Arjan updates the e1000e driver to improve boot time by over 100 msec by
reducing the usleep ranges suring system startup.
Artem updates the igb driver register dump in ethtool, first prepares
the register dump for future additions of registers in the dump, then
secondly, adds the RR2DCDELAY register to the dump. When dealing with
time-sensitive networks, this register is helpful in determining your
latency from the device to the ring.
Alex fixes the ixgbevf driver to use the current cached link state,
rather than trying to re-check the value from the PF.
Harshitha adds support for MACVLAN offloads in i40e by using channels as
MACVLAN interfaces.
Detlev Casanova updates the e1000e driver to use delayed work instead of
timers to run the watchdog.
Vitaly fixes an issue in e1000e, where when disconnecting and
reconnecting the physical cable connection, the NIC enters a DMoff
state. This state causes a mismatch in link and duplexing, so check the
PCIm function state and perform a PHY reset when in this state to
resolve the issue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware versions do not support this so use the silent variant
to send the message to firmware to suppress the harmless error. This
error message is unnecessarily alarming the user.
Fixes: afdc8a8484 ("bnxt_en: Add DCBNL DSCP application protocol support.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an earlier commit to improve NQ reservations on 57500 chips, we
set the resv_irqs on the 57500 VFs to the fixed value assigned by
the PF regardless of how many are actually used. The current
code assumes that resv_irqs minus the ones used by the network driver
must be the ones for the RDMA driver. This is no longer true and
we may return more MSIX vectors than requested, causing inconsistency.
Fix it by capping the value.
Fixes: 01989c6b69 ("bnxt_en: Improve NQ reservations.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
