We need to preserve the "iio_evgen->irq_sim_domain" error code before
we free "iio_evgen" otherwise it leads to a use after free.
Fixes: 337cbeb2c1 ("genirq/irq_sim: Simplify the API")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The interrupt simulator API exposes a lot of custom data structures and
functions and doesn't reuse the interfaces already exposed by the irq
subsystem. This patch tries to address it.
We hide all the simulator-related data structures from users and instead
rely on the well-known irq domain. When creating the interrupt simulator
the user receives a pointer to a newly created irq_domain and can use it
to create mappings for simulated interrupts.
It is also possible to pass a handle to fwnode when creating the simulator
domain and retrieve it using irq_find_matching_fwnode().
The irq_sim_fire() function is dropped as well. Instead we implement the
irq_get/set_irqchip_state interface.
We modify the two modules that use the simulator at the same time as
adding these changes in order to reduce the intermediate bloat that would
result when trying to migrate the drivers in separate patches.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for IIO
Link: https://lore.kernel.org/r/20200514083901.23445-3-brgl@bgdev.pl
The variable no longer does anything.
It should have been removed with commit 2e036804d7 ("iio: buffer: remove
'scan_el_attrs' attribute group from buffer struct").
That was about the last time this was needed.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add driver for Atlas EZO line of sensors with initial support for
CO2 the sensor. This is effectively ASCII strings proxied over I2C
due to these series of sensors being by default UART.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Exynos7-specific code bits in ADC driver do not play with PHY:
the field exynos_adc_data.needs_adc_phy is not set in exynos7_adc_data
instance. Therefore the initialization code does not have to check if
it is true.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently the driver only exposes the raw counts. As we
have the regulator voltage and the maximum value (stored in
the data mask), we can trivially produce a scaling fraction
of voltage / max value.
This assumes that the regulator voltage is in fact the max
voltage, which appears to be the case for all mainline dts
and cross referenced with the public Exynos4412 and S5PV210
datasheets.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is clear that we transition to INDIO_DIRECT_MODE when disabling the
buffer(s) and it is also clear that we transition from INDIO_DIRECT_MODE
when enabling the buffer(s). So leaving the currentmode field
INDIO_DIRECT_MODE until after the preenable() callback and updating it to
INDIO_DIRECT_MODE before the postdisable() callback doesn't add additional
value. On the other hand some drivers will need to perform different
actions depending on which mode the device is going to operate in/was
operating in.
Moving the update of currentmode before preenable() and after postdisable()
enables us to have drivers which perform mode dependent actions in those
callbacks.
Note, was originally not intended as such, but fixes an issue introduced
in the at91-sama5d2 adc driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Fixes: 065056cb0d ("iio: at91-sama5d2_adc: split at91_adc_current_chan_is_touch() helper")
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
This also changes some internal functions to pass the pointer to the
state-struct vs a ref to indio_dev just to access the state-struct again.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
This also changes some internal functions to pass the pointer to the
state-struct vs a ref to indio_dev just to access the state-struct again.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bma150/smb380 are very similar to the bma023 but have a temperature
channel as well.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bma180 driver is being extended to support the bma150.
Its temperature channel is unsigned so the center_temp naming
no longer makes.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bma023 chip is similar enough to the bma180 and bma25x that the
same driver can support all of them. The biggest differences are
the lack of a temperature channel and no low power but still working
mode.
The bma150 is a close relative of the bma023, but it does have a
temperature channel so support is not added for it.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bma180 IIO driver is being extended for support for the chips
support by input's bma150 driver (bma023, bma150, smb380). Don't
allow both drivers to be enabled simultaneously as they're for the
same hardware.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some variants of the bma180 (eg bma023) have different reset
values. In preparation for adding support for them, factor
out the reset value into the chip specific data.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Usual mixed back but with a few subsystem wide or device type
wide cleanups.
New device support
* adis16475
- New driver supporting adis16470, adis16475, adis16477, adis16465,
adis16467, adis16500, adis16505 and adis16507.
Includes some rework of the adis library to simplify using it
for this new driver.
* ak8974
- Add support for Alps hscdt008a. ID only. Related patches add support
for scale.
* atlas-sensor
- Add support for RTD-SM OEM temperature sensor.
* cm32181
- Add support for CM3218 including support for SMBUS alert via
ACPI resources.
* ltc2632
- Add support for ltc2634-12/10/8 DACS including handling per
device type numbers of channels.
Major Features
* cm32181
- ACPI bindings including parsing CPM0 and CPM1 custom ACPI tables.
Includes minor tidy ups and fixes.
* vcnl4000
- Add event support
- Add buffered data capture support
- Add control of sampling frequency
Cleanups and minor fixes.
* core
- Trivial rework of iio_device_alloc to use an early return and
improve readability.
- Precursors to addition of multiple buffer support. So far
minor refactoring.
* subsystem wide
- Use get_unaligned_be24 slightly improve readability over open
coding it.
* adis drivers
- Use iio_get_debugfs_dentry access function.
* bh1780, cm32181, cm3232, gp2ap02a00f, opt3001, st_uvis25, vl6180,
dmard06, kxsd9
- Drop use of of_match_ptr to allow ACPI based probing via PRP0001.
Part of clear out of this to avoid cut and paste into new drivers.
* ad5592r, ad5593r
- Fix typos
* ad5933
- Use managed interfaces to automate error handling and remove.
* ak8974
- Fix wrong number of 'real bits' for buffered data.
- Refactor to pull measurement code out as separate function.
bmp280
- Fix lack of clamp on range during data capture.
* at91-sama5d2_adc
- Handle unfinished conversions correctly.
- Allow use of triggers other than it's own.
- Reorganize buffer setup and tear down as part of long running
subsystem wide rework.
* ccs811
- Add DT binding docs and match table.
- Support external reset and wakeup pins.
* hid-sensors
- Reorganize buffer setup and tear down as part of long running
subsystem wide rework.
* ltr501
- Constify some structs.
* vcnl4000
- Fix an endian issue by using explicit byte swapped i2c accessors.
-----BEGIN PGP SIGNATURE-----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=mYqq
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.8b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new device support, cleanups and features for IIO in the 5.8 cycle
Usual mixed back but with a few subsystem wide or device type
wide cleanups.
New device support
* adis16475
- New driver supporting adis16470, adis16475, adis16477, adis16465,
adis16467, adis16500, adis16505 and adis16507.
Includes some rework of the adis library to simplify using it
for this new driver.
* ak8974
- Add support for Alps hscdt008a. ID only. Related patches add support
for scale.
* atlas-sensor
- Add support for RTD-SM OEM temperature sensor.
* cm32181
- Add support for CM3218 including support for SMBUS alert via
ACPI resources.
* ltc2632
- Add support for ltc2634-12/10/8 DACS including handling per
device type numbers of channels.
Major Features
* cm32181
- ACPI bindings including parsing CPM0 and CPM1 custom ACPI tables.
Includes minor tidy ups and fixes.
* vcnl4000
- Add event support
- Add buffered data capture support
- Add control of sampling frequency
Cleanups and minor fixes.
* core
- Trivial rework of iio_device_alloc to use an early return and
improve readability.
- Precursors to addition of multiple buffer support. So far
minor refactoring.
* subsystem wide
- Use get_unaligned_be24 slightly improve readability over open
coding it.
* adis drivers
- Use iio_get_debugfs_dentry access function.
* bh1780, cm32181, cm3232, gp2ap02a00f, opt3001, st_uvis25, vl6180,
dmard06, kxsd9
- Drop use of of_match_ptr to allow ACPI based probing via PRP0001.
Part of clear out of this to avoid cut and paste into new drivers.
* ad5592r, ad5593r
- Fix typos
* ad5933
- Use managed interfaces to automate error handling and remove.
* ak8974
- Fix wrong number of 'real bits' for buffered data.
- Refactor to pull measurement code out as separate function.
bmp280
- Fix lack of clamp on range during data capture.
* at91-sama5d2_adc
- Handle unfinished conversions correctly.
- Allow use of triggers other than it's own.
- Reorganize buffer setup and tear down as part of long running
subsystem wide rework.
* ccs811
- Add DT binding docs and match table.
- Support external reset and wakeup pins.
* hid-sensors
- Reorganize buffer setup and tear down as part of long running
subsystem wide rework.
* ltr501
- Constify some structs.
* vcnl4000
- Fix an endian issue by using explicit byte swapped i2c accessors.
* tag 'iio-for-5.8b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (74 commits)
iio: light: ltr501: Constify structs
staging: iio: ad5933: attach life-cycle of kfifo buffer to parent device and use managed calls throughout
iio: bmp280: fix compensation of humidity
iio: light: cm32181: Fix integartion time typo
iio: light: cm32181: Add support for parsing CPM0 and CPM1 ACPI tables
iio: light: cm32181: Make lux_per_bit and lux_per_bit_base_it runtime settings
iio: light: cm32181: Use units of 1/100000th for calibscale and lux_per_bit
iio: light: cm32181: Change reg_init to use a bitmap of which registers to init
iio: light: cm32181: Handle CM3218 ACPI devices with 2 I2C resources
iio: light: cm32181: Clean up the probe function a bit
iio: light: cm32181: Add support for the CM3218
iio: light: cm32181: Add some extra register defines
iio: light: cm32181: Add support for ACPI enumeration
iio: light: cm32181: Switch to new style i2c-driver probe function
iio: hid-sensors: move triggered buffer setup into hid_sensor_setup_trigger
iio: vcnl4000: Add buffer support for VCNL4010/20.
iio: vcnl4000: Add sampling frequency support for VCNL4010/20.
iio: vcnl4000: Add event support for VCNL4010/20.
iio: vcnl4000: Factorize data reading and writing.
iio: vcnl4000: Fix i2c swapped word reading.
...
Constify some data structs that are never changed. In order to do so,
also update a couple of functions that now need to accept pointers to
const struct instead of struct. While at it, update a few more functions
to accept pointers to const struct instead of pointers.
This allows the compiler to put more data in the code segment instead of
the data segment, as seen by the output of the file command:
Before:
text data bss dec hex filename
27080 8144 192 35416 8a58 drivers/iio/light/ltr501.o
After:
text data bss dec hex filename
27688 7536 192 35416 8a58 drivers/iio/light/ltr501.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Limit the output of humidity compensation to the range between 0 and 100
percent.
Depending on the calibration parameters of the individual sensor it
happens, that a humidity above 100 percent or below 0 percent is
calculated, which don't make sense in terms of relative humidity.
Add a clamp to the compensation formula as described in the datasheet of
the sensor in chapter 4.2.3.
Although this clamp is documented, it was never in the driver of the
kernel.
It depends on the circumstances (calibration parameters, temperature,
humidity) if one can see a value above 100 percent without the clamp.
The writer of this patch was working with this type of sensor without
noting this error. So it seems to be a rare event when this bug occures.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix integartion time typo and while at it improve the comment with
the typo a bit in general.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On ACPI based systems the CPLM3218 ACPI device node describing the
CM3218[1] sensor typically will have some extra tables with register
init values for initializing the sensor and calibration info.
This is based on a newer version of cm32181.c, with a copyright of:
* Copyright (C) 2014 Capella Microsystems Inc.
* Author: Kevin Tsai <ktsai@capellamicro.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2, as published
* by the Free Software Foundation.
Which is floating around on the net in various places, but the changes
from this newer version never made it upstream.
This was tested on the following models: Acer Switch 10 SW5-012 (CM32181)
Asus T100TA (CM3218), Asus T100CHI (CM3218) and HP X2 10-n000nd (CM32181).
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This looks really unusual to have a 'get_device()' hidden in a 'dev_err()'
call.
Remove it.
While at it add a missing \n at the end of the message.
Fixes: 574fb258d6 ("Staging: IIO: VTI sca3000 series accelerometer driver (spi)")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make lux_per_bit and lux_per_bit_base_it settings stored in struct
cm32181_chip instead of a hardcoded (defined) values.
This is a preparation patch for reading some ACPI tables which specify
a device specific lux_per_bit value.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use units of 1/100000th for calibscale and lux_per_bit. The similar
cm3232 driver already uses 1/100000th as unit for calibscale.
This allows for higher-accuracy and makes it easier to add support
for getting device-specific calibscale and lux_per_bit values from
a device's ACPI tables, as the values in the ACPI tables also use
1/100000th units.
This units change means that our intermediate values in cm32181_get_lux()
may get quite big, change the type of the lux variable to a u64 to
deal with this.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a preparation patch for reading some ACPI tables which give
init values for multiple registers.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some ACPI systems list 2 I2C resources for the CM3218 sensor. On these
systems the first I2cSerialBus ACPI-resource points to the SMBus Alert
Response Address (ARA, 0x0c) and the second I2cSerialBus ACPI-resource
points to the actual CM3218 sensor address:
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (SBUF, ResourceTemplate ()
{
I2cSerialBusV2 (0x000C, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.I2C3",
0x00, ResourceConsumer, , Exclusive,
)
I2cSerialBusV2 (0x0048, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.I2C3",
0x00, ResourceConsumer, , Exclusive,
)
Interrupt (ResourceConsumer, Level, ActiveHigh, Exclusive, ,, )
{
0x00000033,
}
})
Return (SBUF) /* \_SB_.I2C3.ALSD._CRS.SBUF */
}
Detect this and take the following step to deal with it:
1. When a SMBus Alert capable sensor has an Alert asserted, it will
not respond on its actual I2C address. Read a byte from the ARA
to clear any pending Alerts.
2. Create a "dummy" client for the actual I2C address and
use that client to communicate with the sensor.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
3 small cleanups to cm32181_probe():
1. Do not log an error when we fail to allocate memory (as a general
rule drivers do not log errors for this as the kernel will already
have complained loudly that it could not alloc the mem).
2. Remove the i2c_set_clientdata() call, we never use i2c_get_clientdata()
or dev_get_drvdata() anywhere.
3. Add a dev helper variable and use it in various places instead of
&client->dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for the CM3218 which is an older version of the
CM32181.
This is based on a newer version of cm32181.c, with a copyright of:
* Copyright (C) 2014 Capella Microsystems Inc.
* Author: Kevin Tsai <ktsai@capellamicro.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2, as published
* by the Free Software Foundation.
Which is floating around on the net in various places, but the changes
from this newer version never made it upstream.
This was tested on an Asus T100TA and an Asus T100CHI, which both come
with the CM3218 variant of the light sensor.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These come from a newer version of cm32181.c, which is floating around
the net, with a copyright of:
* Copyright (C) 2014 Capella Microsystems Inc.
* Author: Kevin Tsai <ktsai@capellamicro.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2, as published
* by the Free Software Foundation.
Note that this removes the bogus CM32181_CMD_ALS_ENABLE define, there
is no enable bit, only a disable bit and enabled is the absence of
being disabled.
This is a preparation patch for adding support for the older
CM3218 model of the light sensor.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for ACPI enumeration, this has been tested on a HP
HP Pavilion x2 Detachable 10 (Bay Trail model).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Switch to the new style i2c-driver probe_new probe function and drop the
unnecessary i2c_device_id table (we do not have any old style board files
using this).
This is a preparation patch for adding ACPI binding support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The main intent here is to get rid of the iio_buffer_set_attrs() helper, or
at least rework it's usage a bit.
The problem with that helper is that it needs a pointer to the buffer,
which makes supporting multiple buffers per IIO device a bit more
cumbersome.
The hid_sensor_setup_trigger() is pretty much used in the same way:
- iio_triggered_buffer_setup() gets called before
- then hid_sensor_setup_trigger() and hid_sensor_setup_batch_mode() gets
called which may attach some fifo attributes
This change merges the 2 together under the hid_sensor_setup_trigger()
function. Only the &iio_pollfunc_store_time is passed to all devices, so
it's not even required to pass it explicitly outside of the common
hid_sensor_setup_trigger() function.
Moving the devm_iio_triggered_buffer_setup/cleanup() calls into the common
place code can help the rework of the buffer code, since it is in one
place.
One detail of the change is that there are 2 drivers that use
devm_iio_triggered_buffer_setup(). That function gets implicitly
replaced with iio_triggered_buffer_setup()/cleanup(), but since all drivers
call both hid_sensor_setup_trigger9) & hid_sensor_remove_trigger() trigger,
the iio_triggered_buffer_cleanup() piggy backs on the
hid_sensor_remove_trigger() call, which should cover the cleanup.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The VCNL4010 and VCNL4020 chips are able to raise interrupts on data ready.
Use it to provide triggered buffer support for proximity data.
Those two chips also provide ambient light data. However, they are sampled
at different rate than proximity data. As this is not handled by the IIO
framework for now, and the sample frequencies of ambient light data are
very low, do add buffer support for them.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add sampling frequency support for proximity data on VCNL4010 and VCNL4020
chips.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The VCNL4010 and VCNL4020 chips are able to raise interrupts on proximity
threshold events. Add support for threshold rising and falling events for
those two chips.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Factorize data reading in vcnl4000_measure into a vcnl4000_read_data
function. Also add a vcnl4000_write_data function.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bytes returned by the i2c reading need to be swapped
unconditionally. Otherwise, on be16 platforms, an incorrect value will be
returned.
Taking the slow path via next merge window as its been around a while
and we have a patch set dependent on this which would be held up.
Fixes: 62a1efb9f8 ("iio: add vcnl4000 combined ALS and proximity sensor")
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core provides a iio_get_debugfs_dentry() helper.
It seems that the ADIS IMU drivers access that field directly.
This change converts them to use iio_get_debugfs_dentry() instead.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
DMA channel request should use device struct from platform device struct.
Currently it's using iio device struct. But at this stage when probing,
device struct isn't yet registered (e.g. device_register is done in
iio_device_register). Since commit 71723a96b8 ("dmaengine: Create
symlinks between DMA channels and slaves"), a warning message is printed
as the links in sysfs can't be created, due to device isn't yet registered:
- Cannot create DMA slave symlink
- Cannot create DMA dma:rx symlink
Fix this by using device struct from platform device to request dma chan.
Fixes: eca949800d ("IIO: ADC: add stm32 DFSDM support for PDM microphone")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
DMA channel request should use device struct from platform device struct.
Currently it's using iio device struct. But at this stage when probing,
device struct isn't yet registered (e.g. device_register is done in
iio_device_register). Since commit 71723a96b8 ("dmaengine: Create
symlinks between DMA channels and slaves"), a warning message is printed
as the links in sysfs can't be created, due to device isn't yet registered:
- Cannot create DMA slave symlink
- Cannot create DMA dma:rx symlink
Fix this by using device struct from platform device to request dma chan.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
During initial submission the selection of the channel was done using
the scan_index member of the iio_chan_spec structure. It was an abuse
because this member is supposed to be used with a buffer so it was
removed.
However there was still the need to be able to known how to select a
channel, the correct member to store this information is address.
Thanks to this it is possible to select any other channel than the
channel 0.
Fixes: 8dd2d7c0fe ("iio: adc: Add driver for the TI ADS8344 A/DC chips")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch add support for Analog Devices (Linear Technology)
LTC2634 Quad 12-/10-/8-Bit Rail-to-Rail DAC.
The SPI functionality based on them from LTC2632 therefor
add the definitions only and update the Kconfig.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The documentation for ltc_2632_chip_info missed the desciption for the
num_channels. This trivial patch adds it.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Fixes: 9f15a4a0ad ("iio: dac: ltc2632: add support for LTC2636 family")
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The manual for the HSCDTD008A gives us a scaling for the
three axis as +/- 2.4mT (24 Gauss) per axis.
The manual for the AMI305 and AMI306 gives us a scaling
for the three axis as +/- 12 Gauss per axis.
Tests with the HSCDTD008A sensor, cat the raw values:
$ cat in_magn_*_raw
raw
45
189
-19
The scaling factor in in_magn_*_scale is 0.001464843,
which gives:
0.065 Gauss
0.277 Gauss
-0.027 Gauss
The earths magnetic field is in the range of 0.25 to 0.65
Gauss on the surface according to Wikipedia, so these
seem like reasonable values.
Again we are guessing that the AK8974 has a 12 bit ADC,
based on the similarity with AMI305 and AMI306.
Cc: Nick Reitemeyer <nick.reitemeyer@web.de>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This breaks out the measurement code to its own function
so we can handle this without swirling it up with the
big switch() statement inside ak8974_read_raw().
Keep a local s16 helper variable for the signed value
coming out of the measurement before assigning it to the
integer *val. The local variable makes the code easier
to read and the compiler will optimize it if possible.
Cc: Nick Reitemeyer <nick.reitemeyer@web.de>
Cc: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The HSCDTD008A has 15 bits of actual ADC valie, and the
AMI305 and AMI306 has 12 bits.
Correct this by providing an extra parameter to the channel
macro and define a separate set of channels for each variant
of the chip. The resolution is the actual resolution of the
internal ADC of the chip.
The values are stored in a S16 in 2's complement so all 16
bits are used for storing (no shifting needed).
The AMI305, AMI306 and HSCDTD008A valid bits are picked from
respective datasheet.
My best educated guess is that AK8974 is also 12 bits. The
AK8973 is an 8 bit and earlier version, and the sibling
drivers AMI305 and AMI306 are 12 bits, so it makes sense
to assume that the AK8974 is also 12 bits.
Cc: Nick Reitemeyer <nick.reitemeyer@web.de>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The hscdtd008a is similar to the AK8974:
Only the whoami value and some registers are different.
Signed-off-by: Nick Reitemeyer <nick.reitemeyer@web.de>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The null check on st->chip_info->convst_channel is redundant because
convst_channel is a 2 element array of struct iio_chan_spec objects
and this can never be null. Fix this by removing the null check.
Addresses-Coverity: ("Array compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change is both cosmetic and a prequel to adding support for attaching
multiple buffers per IIO device.
The IIO buffer sysfs attrs are mostly designed to support only one attached
buffer, and in order to support more, we need to centralize [in each attr
function] the buffer which is being accessed.
This also makes it a bit more uniform, as in some functions there is a
short-hand 'buffer' variable and at the same time the 'indio_dev->buffer'
is still access directly.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This module is related to AD5592R, not AD5593R, so be consistent in naming.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This module is related to AD5593R, not AD5592R.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use these functions instead of open-coding them.
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Cc: Song Qiang <songqiang1304521@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Cc: Maxime Roussin-Bélanger <maxime.roussinbelanger@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Noticed whilst reviewing Alexandru's patch to the same function.
If we simply flip the logic and return NULL immediately after memory
allocation failure we reduce the indent of the following block and
end up with more 'idiomatic' kernel code.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Add devicetree OF match table support for CCS811 VOC sensor.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
CCS811 VOC sensor exposes nRESET and nWAKE pins which can be connected
to GPIO pins of the host controller. These pins can be used to externally
release the device from reset and also to wake it up before any I2C
transaction. The initial driver support assumed that the nRESET pin is not
connected and the nWAKE pin is tied to ground.
This commit improves it by adding support for controlling those two pins
externally using a host controller. For the case of reset, if the hardware
reset is not available, the mechanism to do software reset is also added.
As a side effect of doing this, the IIO device allocation needs to be
slightly moved to top of probe to make use of priv data early.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support ADIS16475 and similar IMU devices. These devices are
a precision, miniature MEMS inertial measurement unit (IMU) that
includes a triaxial gyroscope and a triaxial accelerometer. Each
inertial sensor combines with signal conditioning that optimizes
dynamic performance.
The driver adds support for the following devices:
* adis16470, adis16475, adis16477, adis16465, adis16467, adis16500,
adis16505, adis16507.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A call to 'vf610_dac_exit()' is missing in an error handling path.
Fixes: 1b983bf42f ("iio: dac: vf610_dac: Add IIO DAC driver for Vybrid SoC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We need the staging fixes in here too, and this resolves a merge issue
with the vt6656 driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to release a lock if st_lsm6dsx_check_odr() fails, we can't
return directly.
Fixes: 76551a3c3d ("iio: imu: st_lsm6dsx: specify slave odr in slv_odr")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add burst_max_len to `adis_burst`. This is useful for devices which
support different burst modes with different sizes. The buffer to be
used in the spi transfer is allocated with this variable making sure
that has space for all burst modes. The spi transfer length should hold
the "real" burst length depending on the current burst mode configured
in the device.
Moreover, `extra_len` in `adis_burst` is made const and it should
contain the smallest extra length necessary for a burst transfer. In
`struct adis` was added a new `burst_extra_len` that should hold the
extra bytes needed depending on the device instance being used.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds a `regmap_update_bits()` like API to the ADIS library.
It provides locked and unlocked variant.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are some ADIS devices that can configure the data ready pin
polarity. Hence, we cannot hardcode our IRQ mask as IRQF_TRIGGER_RISING
since we might want to have it as IRQF_TRIGGER_FALLING.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for a managed device version of
adis_setup_buffer_and_trigger. It works exactly as the original
one but it calls all the devm_iio_* functions to setup an iio
buffer and trigger. Hence we do not need to care about cleaning those
and we do not need to support a remove() callback for every driver using
the adis library.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
poll functions.
In most cases the iio_triggered_buffer_postenable() should be called first
to attach the poll function, and then the driver can init the data to be
triggered.
In this case it's the other way around: the DMA code should be initialized
before the attaching the poll function and the reverse should be done when
un-initializing.
To make things easier when removing the iio_triggered_buffer_postenable() &
iio_triggered_buffer_predisable() functions from the IIO core API, the DMA
code has been moved into preenable() for init, and postdisable() for
uninit.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change moves the logic to check if the current channel is the
touchscreen channel to a separate helper.
This reduces some code duplication, but the main intent is to re-use this
in the next patches.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change will allow the at91-sama5d2_adc driver to use other triggers
than it's own.
In particular, tested with the sysfs trigger.
To be able to achieve this functionality, some changes were required:
1) Do not enable/disable channels when enabling/disabling the trigger.
This is because the trigger is enabled/disabled only for our trigger
(obviously). We need channels enabled/disabled regardless of what trigger is
being used.
2) Cope with DMA : DMA cannot be used when using another type of trigger.
Other triggers work through pollfunc, so we get polled anyway on every trigger.
Thus we have to obtain data at every trigger.
3) When to start conversion? The usual pollfunc (store time from subsystem)
would be in hard irq and this would be a good way, but current iio subsystem
recommends to have it in the threaded irq. Thus adding software start
code in this handler.
4) Buffer config: we need to setup buffer regardless of our own device's
trigger. We may get one attached later.
5) IRQ handling: we use our own device IRQ only if it's our own trigger
and we do not use DMA . If we use DMA, we use the DMA controller's IRQ.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It can happen that on IRQ trigger, not all conversions are done if
we are enabling multiple channels.
The IRQ is triggered on first EOC (end of channel), but it can happen
that not all channels are done. This leads into erroneous reports to
userspace (zero values or previous values).
To solve this, in trigger handler, check if the mask of done channels
is the same as the mask of active scan channels.
If it's the same, proceed and push to buffers. Otherwise, use usleep
to sleep until the conversion is done or we timeout.
Normally, it should happen that in a short time fashion, all channels are
ready, since the first IRQ triggered.
If a hardware fault happens (for example the clock suddently dissappears),
the handler will not be completed, in which case we do not report anything to
userspace anymore.
Also, change from using the EOC interrupts to DRDY interrupt.
This helps with the fact that not 'n' interrupt statuses are enabled,
each being able to trigger an interrupt, and instead only data ready
interrupt can wake up the CPU. Like this, when data is ready, check in
handler which and how many channels are done. While the DRDY is raised,
other IRQs cannot occur. Once the channel data is being read, we ack the
IRQ and finish the conversion.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enables probing via ACPI PRP0001 route and removes an example of
an approach we no longer want people to copy.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Enables probing via ACPI PRP0001 and removes an example that we don't
want people to cut and paste into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Enables probing via ACPI PRP0001 but mostly about removing examples
that might be copied to new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Also drops ifdef protections for CONFIG_OF.
Enables probing via ACPI PRP0001 and removes an example that might be
cut and paste into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Enables ACPI probing via PRP0001 and removes an example that might
be cut and paste to a new driver.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Enables probing via the ACPI PRP0001 route but more is mosty about
removing examples of this that might get copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Whilst this enables ACPI binding or the device via PRP0001 the
primary aim is to remove potential for these two things to be
cut and paste into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Enables ACPI DSDT to probe via PRP0001 and the compatible property. Also
removes the ifdef protections for CONFIG_OF.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enables ACPI DSDT to probe via PRP0001 and the compatible property.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Atlas Scientific RTD-SM OEM sensor reads temperature using
resistance temperature detector technology.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IIO_CONCENTRATION channel for the DO-SM shouldn't be indexed as
there isn't more than one, and also ATLAS_CONCENTRATION_CHANNEL
macro scan_index define steps on the IIO_TIMESTAMP channel.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Fixes: a751b8e480 (iio: chemical: atlas-sensor: add DO-SM module support)
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
-----BEGIN PGP SIGNATURE-----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=DyTF
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new IIO device support, features and cleanup for the 5.8 cycle
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
* tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (101 commits)
iio: magnetometer: ak8974: Silence deferred-probe error
Documentation: ABI: document IIO in_proximity_nearlevel file
iio: vcnl4000: Export near level property for proximity sensor
dt-bindings: iio: light: vcnl4000: Add proximity-near-level
dt-bindings: iio: Introduce common properties for iio sensors
dt-bindings: iio: vcnl4000: convert bindings to YAML format
iio: Fix misspellings of "Analog Devices"
iio: light: isl29125: fix iio_triggered_buffer_{predisable,postenable} positions
iio: adc: fsl-imx25-gcq: Use devm_platform_ioremap_resource
iio: adc: at91-adc: Use devm_platform_ioremap_resource
iio: adc: sun4i-gpadc-iio: Use devm_platform_ioremap_resource
iio:light:ltr501: Drop unnecessary cast of parameter in regmap_bulk_read
iio:magn:mmc35240: Drop unnecessary casts of val parameter in regmap_bulk*
iio:imu:mpu6050: Tidy up parameters to regmap_bulk functions.
iio:chemical:bme680: Tidy up parameters to regmap_bulk_read
iio:chemical:atlas-sensor: Drop unnecessary explicit casts in regmap_bulk_read calls
iio:accel:mxc4005: Drop unnecessary explicit casts in regmap_bulk_read calls
iio: imu: st_lsm6dsx: drop huge include in sensor-hub driver
iio: buffer: drop devm_iio_kfifo_free() API call
iio: buffer: drop devm_iio_hw_consumer_free() API call
...
Includes one MAINTAINERS update to avoid people getting a lot of bounce
messages and complaining about it.
* MAINTAINERS
- Drop Stefan Popa's Analog Devices email address in favour of
Michael Hennerich.
* core
- Fix handling of dB sysfs inputs.
- Drop a stray semi colon in macro definition.
* ad5770r
- Fix an off by one in chec on maximum number of channels.
* ad7192
- Fix a null pointer de-reference due to the name previously being
retrieved from the spi_get_device_id call which no longer works as
the relevant table was removed.
* ad7797
- Use correct attribute group.
* counter/104-quad-8
- Add locks to prevent some race conditions.
* inv-mpu6050
- Fix issues around suspend / resume clashing with runtime PM.
* stm32-adc
- Fix sleep in invalid context
- Fix id relative path error in device tree binding doc.
* st_lsm6dsx
- Fix a read alignment issue on an untagged FIFO.
- Handle odr for slave to properly compute the FIFO data layout / pattern.
- Flush the HW FIFO before resettting the device to avoid a race on
interrupt line 1.
* st_sensors
- Rely on ODR mask not ODR address to identify if the ODR can be set.
Some devices have an ODR address of 0.
* ti-ads8344
- Byte ordering was wrong - fix it.
* xilinx-xadc
- Fix inverted logic in powering down the second ADC.
- Fix clearing interrupt when enabling the trigger.
- Fix configuration of sequencer when in simultaneous sampling mode.
- Limit initial sampling rate as done for runtime configured ones.
-----BEGIN PGP SIGNATURE-----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=SmJy
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.7 cycle.
Includes one MAINTAINERS update to avoid people getting a lot of bounce
messages and complaining about it.
* MAINTAINERS
- Drop Stefan Popa's Analog Devices email address in favour of
Michael Hennerich.
* core
- Fix handling of dB sysfs inputs.
- Drop a stray semi colon in macro definition.
* ad5770r
- Fix an off by one in chec on maximum number of channels.
* ad7192
- Fix a null pointer de-reference due to the name previously being
retrieved from the spi_get_device_id call which no longer works as
the relevant table was removed.
* ad7797
- Use correct attribute group.
* counter/104-quad-8
- Add locks to prevent some race conditions.
* inv-mpu6050
- Fix issues around suspend / resume clashing with runtime PM.
* stm32-adc
- Fix sleep in invalid context
- Fix id relative path error in device tree binding doc.
* st_lsm6dsx
- Fix a read alignment issue on an untagged FIFO.
- Handle odr for slave to properly compute the FIFO data layout / pattern.
- Flush the HW FIFO before resettting the device to avoid a race on
interrupt line 1.
* st_sensors
- Rely on ODR mask not ODR address to identify if the ODR can be set.
Some devices have an ODR address of 0.
* ti-ads8344
- Byte ordering was wrong - fix it.
* xilinx-xadc
- Fix inverted logic in powering down the second ADC.
- Fix clearing interrupt when enabling the trigger.
- Fix configuration of sequencer when in simultaneous sampling mode.
- Limit initial sampling rate as done for runtime configured ones.
* tag 'iio-fixes-for-5.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
MAINTAINERS: remove Stefan Popa's email
iio: adc: ad7192: fix null pointer de-reference crash during probe
iio: core: remove extra semi-colon from devm_iio_device_register() macro
iio: adc: ti-ads8344: properly byte swap value
iio: imu: inv_mpu6050: fix suspend/resume with runtime power
iio: st_sensors: rely on odr mask to know if odr can be set
iio: xilinx-xadc: Make sure not exceed maximum samplerate
iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode
iio: xilinx-xadc: Fix clearing interrupt when enabling trigger
iio: xilinx-xadc: Fix ADC-B powerdown
iio: dac: ad5770r: fix off-by-one check on maximum number of channels
iio: imu: st_lsm6dsx: flush hw FIFO before resetting the device
iio: core: Fix handling of 'dB'
dt-bindings: iio: adc: stm32-adc: fix id relative path
counter: 104-quad-8: Add lock guards - generic interface
iio: imu: st_lsm6dsx: specify slave odr in slv_odr
iio: imu: st_lsm6dsx: fix read misalignment on untagged FIFO
iio: adc: stm32-adc: fix sleep in atomic context
iio:ad7797: Use correct attribute_group
When the 'spi_device_id' table was removed, it omitted to cleanup/fix the
assignment:
'indio_dev->name = spi_get_device_id(spi)->name;'
After that patch 'spi_get_device_id(spi)' returns NULL, so this crashes
during probe with null de-ref.
This change fixes this by introducing an ad7192_chip_info struct, and
defines all part-names [that should be assigned to indio_dev->name] in a
'ad7192_chip_info_tbl' table.
With this change, the old 'st->devid' is also moved to be a
'chip_info->chip_id'. And the old 'ID_AD719X' macros have been renamed to
'CHIPID_AD719X'. Tld identifiers have been re-purposed to be enum/index
values in the new 'ad7192_chip_info_tbl'.
This should fix the bug, and maintain the ABI for the 'indio_dev->name'
field.
Fixes: 66614ab2be ("staging: iio: adc: ad7192: removed spi_device_id")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The first received byte is the MSB, followed by the LSB so the value needs
to be byte swapped.
Also, the ADC actually has a delay of one clock on the SPI bus. Read three
bytes to get the last bit.
Fixes: 8dd2d7c0fe ("iio: adc: Add driver for the TI ADS8344 A/DC chips")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Suspend/resume were not working correctly with pm runtime.
Now suspend check if the chip is already suspended, and
resume put runtime pm in the correct state.
Issues seen prior to this were:
When entering suspend, there was an error in logs because we
were disabling vddio regulator although it was already disabled.
And when resuming, the chip was pull back to full power but the
pm_runtime state was not updated. So it was believing it was
still suspended.
Fixes: 4599cac846 ("iio: imu: inv_mpu6050: use runtime pm with autosuspend")
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Indeed, relying on addr being not 0 cannot work because some device have
their register to set odr at address 0. As a matter of fact, if the odr
can be set, then there is a mask.
Sensors with ODR register at address 0 are: lsm303dlh, lsm303dlhc, lsm303dlm
Fixes: 7d24517267 ("iio: common: st_sensors: check odr address value in st_sensors_set_odr()")
Signed-off-by: Lary Gibaud <yarl-baudig@mailoo.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The XADC supports a samplerate of up to 1MSPS. Unfortunately the hardware
does not have a FIFO, which means it generates an interrupt for each
conversion sequence. At one 1MSPS this creates an interrupt storm that
causes the system to soft-lock.
For this reason the driver limits the maximum samplerate to 150kSPS.
Currently this check is only done when setting a new samplerate. But it is
also possible that the initial samplerate configured in the FPGA bitstream
exceeds the limit.
In this case when starting to capture data without first changing the
samplerate the system can overload.
To prevent this check the currently configured samplerate in the probe
function and reduce it to the maximum if necessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.
The meaning of the sequencing register for the aux channels changes
depending on the mode.
In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.
In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.
Currently the driver does not have the special handling required for
simultaneous mode. Add it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.
The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently there is an off-by-one check on the number of channels that
will cause an arry overrun in array st->output_mode when calling the
function d5770r_store_output_range. Fix this by using >= rather than >
to check for maximum number of channels.
Addresses-Coverity: ("Out-of-bounds access")
Fixes: cbbb819837 ("iio: dac: ad5770r: Add AD5770R support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
flush hw FIFO before device reset in order to avoid possible races
on interrupt line 1. If the first interrupt line is asserted during
hw reset the device will work in I3C-only mode (if it is supported)
Fixes: 801a6e0af0 ("iio: imu: st_lsm6dsx: add support to LSM6DSO")
Fixes: 43901008fd ("iio: imu: st_lsm6dsx: add support to LSM6DSR")
Reported-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Vitor Soares <vitor.soares@synopsys.com>
Tested-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes the call to iio_str_to_fixpoint when using 'dB' sufix.
Before this the scale_db was not used when parsing the string written to
the attribute and it failed with invalid value.
Fixes: b852822474 ("iio: core: Handle 'dB' suffix in core")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's not uncommon that voltage regulator becomes available later during
kernel's boot process. This patch adds info message about unavailable
regulators in a case of the deferred-probe error and also amends the
error message with a error code.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When an object can be considered close to the sensor is hardware
dependent. Allowing to configure the property via device tree
allows to configure this device specific value.
This is useful for e.g. iio-sensor-proxy to indicate to userspace
if an object is close to the sensor.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to https://www.analog.com/, the company name is spelled
"Analog Devices".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
For the predisable hook, the disable code should occur before detaching
the poll func, and for the postenable hook, the poll func should be
attached before the enable code.
This change reworks the predisable/postenable hooks so that the pollfunc is
attached/detached in the correct position.
It also balances the calls a bit, by grouping the preenable and the
iio_triggered_buffer_postenable() into a single
isl29125_buffer_postenable() function.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to
platform_get_resource() and devm_ioremap_resource()
together. It reduces boilerplate and suggested by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to
platform_get_resource() and devm_ioremap_resource()
together. It reduces boilerplate and suggested by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together. Reduces boilerplate and suggested
by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This only occurs once in the driver and isn't needed in this case either,
so drop it.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Given the parameter is void *, casting to u8 * is unnecessary.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
A mixture of:
* Casts to u8 * for the val parameter which is void * and so needs no cast.
* Explicit sizes when we can use sizeof on the destination / source variable.
Not broken in anyway, I'm just trying to tidy up the is in the subsystem to
avoid it getting cut and paste into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
A mixture of:
* Unnecessary casts of val parameter to u8 * which makes little sense as
the function take a void *.
* Explicit sizes where we can use the destination type to define that.
Note that's not true in all cases as we do read 3 bytes into 4 byte
destinations.
Note that noting was broken here, I'm just trying to ensure this doesn't
get cut and paste into more drivers so cleaning these out subsystem wide.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Himanshu Jha <himanshujha199640@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
regmap_bulk_read takes a void * for its val parameter. It certainly
makes no sense to cast to a (u8 *) + no need to explicitly cast
at all when converting another pointer type to void *.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
regmap_bulk_read takes a void * for its val parameter. It certainly
makes no sense to cast to a (u8 *) + no need to explicitly cast
at all when converting another pointer type to void *.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
st_lsm6dsx is a standalone driver for STM IMU sensors and does not rely
on st_sensor common framework, so it does not include st_sensor common
definitions.
In st_lsm6dsx_shub driver st_sensors.h is used just to introduce the
default wai address for LIS3MDL sensor.
Drop this largely unconnected include file and introduce the default wai
address for LIS3MDL in st_lsm6dsx_ext_dev_settings register map
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
This is the last user of 'devm_iio_device_match()', so it can be removed as
well in this patch.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Moves this to be the first check, as it's very simple and fails the
registration earlier, instead of potentially initializing the
'indio_dev->label' and checking for duplicate indexes, and then failing
with this simple-check.
This is a minor optimization, since '__iio_device_register()' will waste
fewer validation cycles in case 'indio_dev->info' is NULL.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This field doesn't seem used. It seems that only 'buffer->attrs' was ever
used to extend sysfs attributes for an IIO buffer.
Moving forward, it may not make sense to keep it. This patch removes the
field and it's initialization code.
Since we want to rework IIO buffer, to be able to add more buffers per IIO
device, we will merge [somehow] the 'buffer' & 'scan_elements' groups, and
we will continue to add the attributes to the 'buffer' group.
Removing it here, will also make the rework here a bit smaller, since
this code will not be present.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.
Fixes: 1fd4567026 ("iio: imu: adis: add support product ID check in adis_initial_startup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix a typo. 'at the a time' -> 'at a time'.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO DMA buffer is a DMA buffer implementation. As such it should
include buffer_impl.h rather than buffer.h.
The include to buffer.h in buffer-dma.h should be buffer_impl.h so it has
access to the struct iio_buffer definition. The code currently only works
because all places that use buffer-dma.h include buffer_impl.h before it.
The include to buffer.h in industrialio-buffer-dma.c can be removed since
those file does not reference any of buffer consumer functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add driver for the Maxim MAX1241 12-bit, single-channel ADC.
Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX1240-MAX1241.pdf
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Alexandru Lazar <alazar@startmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for STMicroelectronics LISHH12 accelerometer in st_accel
framework.
https://www.st.com/resource/en/datasheet/lis2hh12.pdf
Signed-off-by: Gaëtan André <rvlander@gaetanandre.eu>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add LIS3MDL register map to sensor hub device table.
Tested with LSM6DSM.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support for sensor with up to 8 different ODR settings.
Required for supporting LIS3MDL as sensor hub slave device.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
debugfs_create_file_unsafe does not protect the fops handed to it
against file removal. DEFINE_DEBUGFS_ATTRIBUTE makes the fops aware of
the file lifetime and thus protects it against removal.
Signed-off-by: Rohit Sarkar <rohitsarkar5398@gmail.com>
Tested-by Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
debugfs_create_file_unsafe does not protect the fops handed to it
against file removal. DEFINE_DEBUGFS_ATTRIBUTE makes the fops aware of
the file lifetime and thus protects it against removal.
Signed-off-by: Rohit Sarkar <rohitsarkar5398@gmail.com>
Tested-by Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce st_lsm6dsx_shub_set_full_scale routine in order to configure
the i2c slave device sensitivity
Tested-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD9467 is a 16-bit, monolithic, IF sampling analog-to-digital converter
(ADC). It is optimized for high performanceover wide bandwidths and ease of
use. The product operates at a 250 MSPS conversion rate and is designed for
wireless receivers, instrumentation, and test equipment that require a high
dynamic range. The ADC requires 1.8 V and 3.3 V power supplies and a low
voltage differential input clock for full performance operation. No
external reference or driver components are required for many applications.
Data outputs are LVDS compatible (ANSI-644 compatible) and include the
means to reduce the overall current needed for short trace distances.
Since the chip can operate at such high sample-rates (much higher than
classical interfaces), it requires that a DMA controller be used to
interface directly to the chip and push data into memory.
Typically, the AXI ADC IP core is used to interface with it.
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/AD9467.pdf
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change adds support for the Analog Devices Generic AXI ADC IP core.
The IP core is used for interfacing with analog-to-digital (ADC) converters
that require either a high-speed serial interface (JESD204B/C) or a source
synchronous parallel interface (LVDS/CMOS).
Usually, some other interface type (i.e SPI) is used as a control interface
for the actual ADC, while the IP core (controlled via this driver), will
interface to the data-lines of the ADC and handle the streaming of data
into memory via DMA.
Because of this, the AXI ADC driver needs the other SPI-ADC driver to
register with it. The SPI-ADC needs to be register via the SPI framework,
while the AXI ADC registers as a platform driver. The two cannot be ordered
in a hierarchy as both drivers have their own registers, and trying to
organize this [in a hierarchy becomes] problematic when trying to map
memory/registers.
There are some modes where the AXI ADC can operate as standalone ADC, but
those will be implemented at a later point in time.
DocLink: https://wiki.analog.com/resources/fpga/docs/axi_adc_ip
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, when using a 'iio_dmaengine_buffer_alloc()', an matching call to
'iio_dmaengine_buffer_free()' must be made.
With this change, this can be avoided by using
'devm_iio_dmaengine_buffer_alloc()'. The buffer will get free'd via the
device's devres handling.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
