I misunderstood original Broadcom comment and used wrong values.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also use b43_radio_wait_value to simplify the code and usleep_range when
needed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Radio should be prepared only before initialization. We need this to be
able to call b43_radio_2059_init conditionally (in the future).
This also documents RF control register a bit.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Broadcom hardware supports auto-adjustment of TX power depending on the
currently used rate. So far all calculations were handled without any
helpers (API) using big arrays and magic offsets.
It seems Broadcom recently decided to clean this up by developing PPR.
Their wlc_ppr.h can be found in open parts of the SDK.
As we plan to implement support for rate-based TX power it makes sense
to also implement our version of PPR as well.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't write them as we don't have gains configured correctly yet.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes workarounds on rev 6+ and cleans code slightly.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Access to PHY and radio registers is indirect on Broadcom hardware and
it seems that addressing on some MIPS SoCs may require flushing. So far
this problem was noticed on 0x4716 SoC only (marketing names: BCM4717,
BCM4718).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most of the PHYs use the same way of accessing registers, so move that
code to the shared place. An exception is G-PHY which sometimes access
A-PHY regs and requires special handling.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Flush radio writes as well and add some tiny optimizations (e.g.
masksetting PHY reg involves reading it, so reset the counter).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When switching from one 5 GHz channel to another 5 GHz channel we need
to make sure BPHY is still in a reset. However to access BPHY register
we have to switch to 2 GHz mode for a moment. Otherwise this may result
in "Data bus error" (noticed by Hauke with BCM43224 connected to the
SoC).
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add lists of chipsets, so people can enable support for their device
easier (at least after checking lspci).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It contains radio 0x2057 rev 14 just like a BCM43217, so it doesn't
require any magic. The main difference is that BCM4313 is 1x1:1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has been tested on 14e4:4328 (BCM4321), 14e4:432b (BCM4322),
14e4:4353 (BCM43224) and 14e4:4359 (BCM43228) which is an almost
complete list of 5 GHz capable device (only BCM43222 is missing).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't have all needed channel tables due to RE process for this
device.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This process requires sending some sample tone, so make sure we're
allowed to transmit first.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So far we were assuming only A-PHY supports 5 GHz.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some radios may share the same ID and revision but differ by a version.
E.g. radio in BCM5357B0 is version 1 and requires specific handling.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer devices need different workarounds for cores 0 and 1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add some missing ops and prepare for new devices support. This patch is
a great stability improvement for BCM43217. Earlier Tenda W322E used to
disconnect every 2 minutes (16 times over 30 minutes). With this fix I
got it running for 4 hours (with iperf) without any disconnection.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes handling channel 14 and adds code for BCM43217.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By the way add few chipsets that were tracked with "wl" dumps.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Seems to be required by some hardware, wl does it every time.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This could be a bit confusing to see warning about lacking support for
5 GHz band if your device supports 2.4 GHz only.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for N-PHY rev 8 with 0x2057 rev 5 is almost ready, but we still
need to figure out how to handle rev 9 first.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialization of N-PHY radio revs 5 and 7 requires writing to 0x1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Type of radio has a major meaning for the driver. There is quite some
code that does initialization/calibration depending on the radio rev.
Knowing radio params is quite important to provide help to users, so
print it even with debugging disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes
b43-phy0: Found Radio: Manuf 0x17F, Version 0x7769, Revision 4
to the
b43-phy0: Found Radio: Manuf 0x17F, Version 0x2069, Revision 4
which matches what closed source driver reports:
$ wl revinfo
radiorev 0x42069000
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows adding more revisions support, spotting lacking tables and
unifies naming schema.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds some cores with 0x2057 radio which will be supported soon as
well as core 40 that I missed in the earlier firmware patch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
