This cleanup patch makes changes to use for_each_pipe loop
during bit-mask assignment of allowed crtc with encoder.
changes:
- use BIT(i) macro instead of (1 << i) (Chris)
changes from V2:
- use int for consistency (Jani)
changes from V3:
- instead use enum pipe (Ville)
changes from V4:
- drop DP/HDMI changes, as already part of patch from ville
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180919083126.31805-1-mahesh1.kumar@intel.com
PSR requires AUX IO power well to be enabled. This was already in place
for CNL, extend this for ICL too. Not enabling the power well results in
the aux error interrupts when the hardware exits PSR.
Reported-by: Casey G Bowman <casey.g.bowman@intel.com>
Reported-by: Jyoti R Yadav <jyoti.r.yadav@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: Jyoti R Yadav <jyoti.r.yadav@intel.com>
Cc: Casey G Bowman <casey.g.bowman@intel.com>
Tested-by: Casey G Bowman <casey.g.bowman@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180914001822.2503-1-dhinakaran.pandiyan@intel.com
commit afb2c4437d ("drm/i915/ddi: Push pipe clock enabling to encoders")
inadvertently stopped enabling the pipe clock for any DP-MST stream
after the first one. It also rearranged the pipe clock enabling wrt.
initial MST payload allocation step (which may or may not be a
problem, but it's contrary to the spec.).
Fix things by making the above commit truly a non-functional change.
Fixes: afb2c4437d ("drm/i915/ddi: Push pipe clock enabling to encoders")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107365
Reported-by: Lyude Paul <lyude@redhat.com>
Reported-by: dmummenschanz@web.de
Tested-by: dmummenschanz@web.de
Tested-by: Lyude Paul <lyude@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: dmummenschanz@web.de
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180831174739.30387-1-imre.deak@intel.com
PLLs are the source clocks for the DDIs so in order to determine the
ddi clock we need to check the PLL configuration.
For MG PHy Ports (C - F), depending on whether it is a TBT PLL or MG
PLL the link lock can be obtained from the the PLL divisors based on
the specification.
v2 (from Paulo):
* Make the algorithm look more like what's in the spec, also document
where we differ form the spec and why.
* Make the code a little more consistent with our coding style.
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817215209.29133-2-paulo.r.zanoni@intel.com
Since Haswell we have no color range indication either in the pipe or
port registers for DP. Instead, there's a separate register for setting
the DP Main Stream Attributes (MSA) directly. The MSA register
definition makes no references to colorimetry, just a vague reference to
the DP spec. The connection to the color range was lost.
Apparently we've failed to set the proper MSA bit for limited, or CEA,
range ever since the first DDI platforms. We've started setting other
MSA parameters since commit dae847991a ("drm/i915: add
intel_ddi_set_pipe_settings").
Without the crucial bit of information, the DP sink has no way of
knowing the source is actually transmitting limited range RGB, leading
to "washed out" colors. With the colorimetry information, compliant
sinks should be able to handle the limited range properly. Native
(i.e. non-LSPCON) HDMI was not affected because we do pass the color
range via AVI infoframes.
Though not the root cause, the problem was made worse for DDI platforms
with commit 55bc60db59 ("drm/i915: Add "Automatic" mode for the
"Broadcast RGB" property"), which selects limited range RGB
automatically based on the mode, as per the DP, HDMI and CEA specs.
After all these years, the fix boils down to flipping one bit.
[Per testing reports, this fixes DP sinks, but not the LSPCON. My
educated guess is that the LSPCON fails to turn the CEA range MSA into
AVI infoframes for HDMI.]
Reported-by: Michał Kopeć <mkopec12@gmail.com>
Reported-by: N. W. <nw9165-3201@yahoo.com>
Reported-by: Nicholas Stommel <nicholas.stommel@gmail.com>
Reported-by: Tom Yan <tom.ty89@gmail.com>
Tested-by: Nicholas Stommel <nicholas.stommel@gmail.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=100023
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107476
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94921
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.9+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180814060001.18224-1-jani.nikula@intel.com
The Gen11 TypeC PHY DDI Buffer chapter, PHY Clock Gating Programming
section says that PHY clock gating should be disabled before starting
voltage swing programming, then enabled after any link training is
complete.
v2: Simple rebase.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-6-paulo.r.zanoni@intel.com
Programming this register is part of the Enable Sequence for
DisplayPort on ICL. Do as the spec says.
v2: Simple rebase.
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-5-paulo.r.zanoni@intel.com
This sequence is used to setup voltage swing before enabling MG PHY DDI
as well as for changing the voltage during DisplayPort Link training.
For ICL, there are two types of DDIs. This sequence needs to be used
for MG PHY DDI which is ports C-F.
v6 (From Manasi):
* Add programming for MG_CLKHUB and MG_TX_DCC as per the
spec updates
v5 (from Paulo):
* Checkpatch.
v4 (from Paulo):
* Fix bogus error message
* Fix copy+paste bugs (missing s/TX1/TX2/ after copy+paste)
* Use the new mask names
* Stay under 80 columns
* Add some blank lines
v3:
* Clear the regs before writing (Paulo)
v2:
* Rename to MG PHY in the function def (Jani Nikula)
* Rebase on top of new revision of other patches in series
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530225344-20373-2-git-send-email-manasi.d.navare@intel.com
Instead of looping over ports and hpd_pins, let's loop over
the encoders when doing hotplug processing. And instead of
depending on dev_priv->irq_port[] to tell us whether the
encoder has the ->hpd_pulse() hook or not, we can just
check for that directly. So we can just nuke irq_port[] entirely.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705164357.28512-5-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
On GLK NUC platforms the HDMI retiming buffer needs additional disabled
time to correctly sync to a faster incoming signal.
When measured on a scope the highspeed lines of the HDMI clock turn off
for ~400uS during a normal resolution change. The HDMI retimer on the
GLK NUC appears to require at least a full frame of quiet time before a
new faster clock can be correctly sync'd. Wait 100ms due to msleep
inaccuracies while waiting for a completed frame. Add a quirk to the
driver for GLK boards that use ITE66317 HDMI retimers.
V2: Add more devices to the quirk list
V3: Delay increased to 100ms, check to confirm crtc type is HDMI.
V4: crtc type check extended to include _DDI and whitespace fixes
v5: Fix white spaces, remove the macro for delay. Revert the crtc type
check introduced in v4.
Cc: Imre Deak <imre.deak@intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105887
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Tested-by: Daniel Scheller <d.scheller.oss@gmail.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710200205.1478-1-radhakrishna.sripada@intel.com
We can simplify the encoder's get_power_domains() hook by calling it
only if the encoder is active. That way the hook can return its power
domains unconditionally without checking the active state by calling
encoder::get_hw_state(). This get_hw_state() query is in fact
redundant since it's already done by intel_modeset_readout_hw_state()
setting the encoder's crtc or leaving it NULL accordingly. Let's use
this fact to decide if the encoder is active.
While at it clarify the comment in intel_ddi_get_power_domains() about
primary vs. fake MST encoders and make sure we never do an incorrect
encoder->dig_port cast for fake MST encoders.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705122654.17072-1-imre.deak@intel.com
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 141432
Addresses-Coverity-ID: 141433
Addresses-Coverity-ID: 141434
Addresses-Coverity-ID: 141435
Addresses-Coverity-ID: 141436
Addresses-Coverity-ID: 1357360
Addresses-Coverity-ID: 1357403
Addresses-Coverity-ID: 1357433
Addresses-Coverity-ID: 1392622
Addresses-Coverity-ID: 1415273
Addresses-Coverity-ID: 1435752
Addresses-Coverity-ID: 1441500
Addresses-Coverity-ID: 1454596
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628223541.GA17665@embeddedor.com
So far we got an AUX power domain reference only for the duration of DP
AUX transfers. However, the following suggests that we also need these
for main link functionality:
- The specification doesn't state whether it's needed or not for main
link functionality, but suggests that these power wells need to be
enabled already during display core initialization (Sequences to
Initialize Display).
- For PSR we need to keep the AUX power well enabled.
- On ICL combo PHY ports (non-TC) the AUX power well is needed for
link training too: while the port is enabled with a DP link training
test pattern trying to toggle the AUX power well will time out.
- On ICL MG PHY ports (TC) the AUX power well is needed also for main
link functionality (both in DP and HDMI modes).
- Windows enables these power wells both for main and AUX lane
functionality.
Based on the above take an AUX power reference for main link
functionality too. This makes a difference only on GEN10+ (GLK+)
platforms, where we have separate port specific AUX power wells.
For PSR we still need to distinguish between port A and the other
ports, since on port A DC states must stay enabled for main link
functionality, but DC states must be disabled for driver initiated
AUX transfers. So re-use the corresponding helper from intel_psr.c.
Since we take now a reference for main link functionality on all DP
ports we can forgo taking the separate power ref for PSR functionality.
v2:
- Make sure DC states stay enabled when taking the ref on port A.
(Ville)
v3: (Ville)
- Fix comment about logic for encoders without a crtc state and
add FIXME note for a simplification to avoid calling get_power_domains
in such cases.
- Use intel_crtc_has_dp_encoder() instead !intel_crtc_has_type(HDMI).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
[Clarified code comments in intel_ddi_main_link_aux_domain() and
intel_ddi_get_power_domains() (Imre)]
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621184449.26634-1-imre.deak@intel.com
ICL DVFS is almost the same as CNL, except for the CDCLK/DDICLK
table. Implement it just like CNL does.
References: commit 48469eced2 ("drm/i915: Use cdclk_state->voltage
on CNL")
References: commit 53e9bf5e81 ("drm/i915: Adjust system agent
voltage on CNL if required by DDI ports")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614221018.19044-1-paulo.r.zanoni@intel.com
On ICL for setting the HDMI infoframe the pipe clock needs to be
enabled, otherwise accessing the VIDEO_DIP_CTL register will hang the
machine.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613170710.15080-5-imre.deak@intel.com
On ICL the pipe clock needs to be enabled before setting the HDMI
infoframe, but these steps are in the reverse order atm. Move the pipe
clock enabling to the encoders, so reordering of the two steps can be
done in a clean way.
No functional change.
v2:
- Rebased on drm-tip.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613172746.18525-1-imre.deak@intel.com
This patch adds a proper HDMI DDI entry level for vswing
programming sequences on ICL.
Spec doesn't specify any default for HDMI tables,
so let's pick the last entry as the default for now
to stay consistent with older platform like CNL.
Cc: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-8-paulo.r.zanoni@intel.com
Start using the new registers for ICL and on.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-13-paulo.r.zanoni@intel.com
PLLs are the source clocks for the DDIs so in order
to determine the ddi clock we need to check the PLL
configuration.
This gets a little tricky for ICL since there is
no register bit that maps directly to the link clock.
So this patch creates a separate function in intel_dpll_mgr.c
to obtain the write array PLL Params and compares the set
pll_params with the table to get the corresponding link
clock.
v2:
- Fix the encoder type check (DK).
- Improve our error checking, return a sane value (Mika, Paulo).
- Fix table entries (Paulo).
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Paulo: implement v2]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180523224444.19017-1-paulo.r.zanoni@intel.com
All connectors may not have best_encoder attached, so don't dereference
encoder pointer for each connector.
Fixes: c27e917e2b ("drm/i915/icl: add basic support for the ICL clocks")
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525155238.7054-1-lucas.demarchi@intel.com
All DDI platforms support the full set of preemph settings for each
supported vswing, so let's use the same code for them. We'll also move
the code into intel_ddi.c so that it sits closer to the actual buf trans
tables.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180517170309.28630-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
This commit introduces the definitions for the ICL clocks and adds the
basic functions to the shared DPLL framework. It adds code for the
Enable and Disable sequences for some PLLs, but it does not have the
code to compute the actual PLL values, which are marked as TODO
comments and should be introduced as separate commits.
Special thanks to James Ausmus for investigating and fixing a bug with
the placement of icl_unmap_plls_to_ports() function.
v2:
- Rebase around dpll_lock changes.
v3:
- The spec now says what the timeouts should be.
- Touch DPCLKA_CFGCR0_ICL at the appropriate time so we don't freeze
the machine.
- Checkpatch found a white space problem.
- Small adjustments before upstreaming.
v4:
- Move the ICL checks out of the *map_plls_to_ports() functions
(James)
- Add extra encoder check (James)
- Call icl_unmap_plls_to_ports() later (James)
v5:
- Rebase after the pll struct changes.
v6:
- Properly make the unmap function based on encoders_post_disable()
with regarding to checks and iterators.
- Address checkpatch comment on "min = max = x()".
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180427231436.9353-1-paulo.r.zanoni@intel.com
On clock recovery this function is called to find out
the max voltage swing level that we could go.
However gen 9 functions use the old buffer translation tables
to figure that out. ICL uses different set of tables for eDP
and DP for both Combo and MG PHY ports. This patch adds the hook
for ICL for getting this information from appropriate buf trans tables.
v5 (from Paulo):
* New rebase after changes to earlier patches.
v4:
* Rebase.
v3:
* Follow the coding conventions here
(https://cgit.freedesktop.org/drm-intel/tree/Documentation/process/codin
g-style.rst#n191) (Paulo)
v2:
* Rebase after patch that adds voltage check inside buf trans
function (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328215803.13835-9-paulo.r.zanoni@intel.com
This is an important part of the DDI initalization as well as
for changing the voltage during DisplayPort link training.
The Voltage swing seqeuence is similar to Cannonlake.
However it has different register definitions and hence
it makes sense to create a separate vswing sequence and
program functions for ICL to leave room for more changes
in case the Bspec changes later and deviates from CNL sequence.
v2:
Use ~TAP3_DISABLE for enbaling that bit (Jani Nikula)
v3:
* Use dw4_scaling column for PORT_TX_DW4 values (Rodrigo)
v4:
* Call it combo_vswing, use switch statement (Paulo)
v5 (from Paulo):
* Fix a typo.
* s/rate < 600000/rate <= 600000/.
* Don't remove blank lines that should be there.
v6:
* Rebased by Rodrigo on top of Cannonlake changes
where non vswing sequences are not aligned with iboost
anymore.
v7: Another rebase after an upstream rework.
v8 (from Paulo):
* Adjust the code to the upstream output type changes.
* Squash the patch that moved some functions up.
* Merge both get_combo_buf_trans functions in order to simplify the
code.
* Change the changelog format.
v9 (from Paulo):
* Use RTERM_SELECT instead of SCALING_MODE_SEL.
* Adjust the output type handling according to how the other platforms
do it now.
v10 (from Paulo):
* Fix comment left out from v9 changes (Rodrigo).
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328215803.13835-8-paulo.r.zanoni@intel.com
When doing a modeset where the sink is transitioning from D3 to D0 , it
would sometimes be possible for the initial power_up_phy() to start
timing out. This would only be observed in the last action before the
sink went into D3 mode was intel_dp_sink_dpms(DRM_MODE_DPMS_OFF). We
originally thought this might be an issue with us accidentally shutting
off the aux block when putting the sink into D3, but since the DP spec
mandates that sinks must wake up within 1ms while we have 100ms to
respond to an ESI irq, this didn't really add up. Turns out that the
problem is more subtle then that:
It turns out that the timeout is from us not enabling DPMS on the MST
hub before actually trying to initiate sideband communications. This
would cause the first sideband communication (power_up_phy()), to start
timing out because the sink wasn't ready to respond. Afterwards, we
would call intel_dp_sink_dpms(DRM_MODE_DPMS_ON) in
intel_ddi_pre_enable_dp(), which would actually result in waking up the
sink so that sideband requests would work again.
Since DPMS is what lets us actually bring the hub up into a state where
sideband communications become functional again, we just need to make
sure to enable DPMS on the display before attempting to perform sideband
communications.
Changes since v1:
- Remove comment above if (!intel_dp->is_mst) - vsryjala
- Move intel_dp_sink_dpms() for MST into intel_dp_post_disable_mst() to
keep enable/disable paths symmetrical
- Improve commit message - dhnkrn
Changes since v2:
- Only send DPMS off when we're disabling the last sink, and only send
DPMS on when we're enabling the first sink - dhnkrn
Changes since v3:
- Check against is_mst, not intel_dp->is_mst - dhnkrn/vsyrjala
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Fixes: ad260ab32a ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.")
Link: https://patchwork.freedesktop.org/patch/msgid/20180407011053.22437-1-lyude@redhat.com
Replace all users of pll->id to use pll->info->id. In functions using
this more than once it was preferred to add an id variable to make the
code easier to read.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320220637.21480-6-lucas.demarchi@intel.com
This table is used for voltage swing programming sequence during DDI
Buffer initialization for MG PHY DDI Buffers on Icelake.
v2 (from Paulo):
* Fix white space issues.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323172419.24911-5-paulo.r.zanoni@intel.com
These tables are used on voltage vswing sequence initialization on
Icelake.
The swing_sel on the spec's table is defined in a 4 bits binary like
1010. However the register bits are split in upper 1 bit swing_sel
and lower 3 bits swing sel.
In this table here we store this value as a single value in hex like
it is mentioned in the Bspec and split it to the upper and lower bit
values only while programming the registers.
For instance: b1010 is written as 0xA and then while writing to the
register, the upper 1 bit is obtained by (0xA & 0x8) and shifting by
appropriate bits while lower 3 bits are obtained by (0xA & 0x7) and
shifting by appropriate bits.
Some of the columns need to be updated after the spec is updated.
v5 (from Paulo):
* Checkpatch fixes.
v4 (from Paulo):
* Fix minor typo
* Coding style conformance
v3:
* Get rid of HDMI/DVI tables, same as DP (Paulo)
* Use combo_phy in ddi buf trans table defs (Paulo)
v2:
* Added DW4_scaling_hex column to the translation tables (Rodrigo)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323172419.24911-3-paulo.r.zanoni@intel.com
When we're disabling the HDMI link we try to reset the scrambling and
TMDS bit clock ratio back to the default values. This will fail if the
sink has already been disconnected. Thus we should not print an error
message when resetting the scrambling/TMDS bit clock ratio fail during
disable. During enable we do want the error, and during disable we may
still want to know what happended for debug purposes so let's use
DRM_DEBUG_KMS() there.
v2: Remember them consts
v3: Go back to just one function and print the errors/debugs
from callers (Shashank)
Cc: Shashank Sharma <shashank.sharma@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105644
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105655
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322154707.22103-1-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
If bios sets up an MST output and hardware state readout code sees this is
an SST configuration, when disabling the encoder we end up calling
->post_disable_dp() hook instead of the MST version. Consequently, we write
to the DP_SET_POWER dpcd to set it D3 state. Further along when we try
enable the encoder in MST mode, POWER_UP_PHY transaction fails to power up
the MST hub. This results in continuous link training failures which keep
the system busy delaying boot. We could identify bios MST boot discrepancy
and handle it accordingly but a simple way to solve this is to write to the
DP_SET_POWER dpcd for MST too.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105470
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 5ea2355a10 ("drm/i915/mst: Use MST sideband message transactions for dpms control")
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314054825.1718-1-dhinakaran.pandiyan@intel.com
We don't want to preserve the DDI A 4 lane bit on ICL.
Fixes: 3d2011cfa4 ("drm/i915/icl: remove port A/E lane sharing limitation.")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306104155.3526-1-jani.nikula@intel.com
LSPCON likes to throw short HPDs during the enable seqeunce prior to the
link being trained. These obviously result in the channel CR/EQ check
failing and thus we schedule a pointless hotplug work to retrain the
link. Avoid that by ignoring the bad CR/EQ status until we've actually
initially trained the link.
I've not actually investigated to see what LSPCON is trying to signal
with the short pulse. But as long as it signals anything I think we're
supposed to check the link status anyway, so I don't really see other
good ways to solve this. I've not seen these short pulses being
generated by normal DP sinks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-5-ville.syrjala@linux.intel.com
Doing link retraining from the short pulse handler is problematic since
that might introduce deadlocks with MST sideband processing. Currently
we don't retrain MST links from this code, but we want to change that.
So better to move the entire thing to the hotplug work. We can utilize
the new encoder->hotplug() hook for this.
The only thing we leave in the short pulse handler is the link status
check. That one still depends on the link parameters stored under
intel_dp, so no locking around that but races should be mostly harmless
as the actual retraining code will recheck the link state if we
end up there by mistake.
v2: Rebase due to ->post_hotplug() now being just ->hotplug()
Check the connector type to figure out if we should do
the HDMI thing or the DP think for DDI
[pushed with whitespace changes for sparse]
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-3-ville.syrjala@linux.intel.com
The LG 4k TV I have doesn't deassert HPD when I turn the TV off, but
when I turn it back on it will pulse the HPD line. By that time it has
forgotten everything we told it about scrambling and the clock ratio.
Hence if we want to get a picture out if it again we have to tell it
whether we're currently sending scrambled data or not. Implement
that via the encoder->hotplug() hook.
v2: Force a full modeset to not follow the HDMI 2.0 spec more
closely (Shashank)
[pushed with whitespace fixes to make sparse happy]
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-1-ville.syrjala@linux.intel.com
Platforms before Gen11 were sharing lanes between port-A & port-E.
This limitation is no more there.
Changes since V1:
- optimize the code (Shashank/Jani)
- create helper function to get max lanes (ville)
Changes since V2:
- Include BIOS fail fix-up in same helper function (ville)
Changes since V3:
- remove confusing if/else (jani)
- group intel_encoder initialization
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206060855.30026-1-mahesh1.kumar@intel.com
Driver Changes:
- Lift alpha_support protection from Cannonlake (Rodrigo)
* Meaning the driver should mostly work for the hardware we had
at our disposal when testing
* Used to be preliminary_hw_support
- Add missing Cannonlake PCI device ID of 0x5A4C (Rodrigo)
- Cannonlake port register fix (Mahesh)
- Fix Dell Venue 8 Pro black screen after modeset (Hans)
- Fix for always returning zero out-fence from execbuf (Daniele)
- Fix HDMI audio when no no relevant video output is active (Jani)
- Fix memleak of VBT data on driver_unload (Hans)
- Fix for KASAN found locking issue (Maarten)
- RCU barrier consolidation to improve igt/gem_sync/idle (Chris)
- Optimizations to IRQ handlers (Chris)
- vblank tracking improvements (64-bit resolution, PM) (Dhinakaran)
- Pipe select bit corrections (Ville)
- Reduce runtime computed device_info fields (Chris)
- Tune down some WARN_ONs to GEM_BUG_ON now that CI has good coverage (Chris)
- A bunch of kerneldoc warning fixes (Chris)
* tag 'drm-intel-next-2018-02-21' of git://anongit.freedesktop.org/drm/drm-intel: (113 commits)
drm/i915: Update DRIVER_DATE to 20180221
drm/i915/fbc: Use PLANE_HAS_FENCE to determine if the plane is fenced
drm/i915/fbdev: Use the PLANE_HAS_FENCE flags from the time of pinning
drm/i915: Move the policy for placement of the GGTT vma into the caller
drm/i915: Also check view->type for a normal GGTT view
drm/i915: Drop WaDoubleCursorLP3Latency:ivb
drm/i915: Set the primary plane pipe select bits on gen4
drm/i915: Don't set cursor pipe select bits on g4x+
drm/i915: Assert that we don't overflow frontbuffer tracking bits
drm/i915: Track number of pending freed objects
drm/i915/: Initialise trans_min for skl_compute_transition_wm()
drm/i915: Clear the in-use marker on execbuf failure
drm/i915: Prune gen8_gt_irq_handler
drm/i915: Track GT interrupt handling using the master iir
drm/i915: Remove WARN_ONCE for failing to pm_runtime_if_in_use
drm: intel_dpio_phy: fix kernel-doc comments at nested struct
drm/i915: Release connector iterator on a digital port conflict.
drm/i915/execlists: Remove too early assert
drm/i915: Assert that we always complete a submission to guc/execlists
drm: move read_domains and write_domain into i915
...
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlqDR7wACgkQlvcN/ahK
BwrxxAgAm3HrrSvtfFPooUsVuodl7KxUF9Mc/MzCNkakP3+Gs0PBE6pp+PhpcBT4
7WwkONTvVKgtnhoIzl8k0Xp8TrDZDWFzpDUluug2knr4nHHkksXtimnz9sfyzGHw
s5XofrV8KQe710grKvUry1VtBrlGRGchd+Xjg1bl+BONnwTmJ8c53npa+d6X0nnt
c+qlP7U9ZawIb59eSL98CuaYsH8oQcMya/jUlb96ky+mx4ugHv9J3ePYIZTqqNDq
/YY1xVhlDQx8iKx7yUp8mreHp5tBL/o3hNNmLMnPDx8jwZfKt7R9MZHH+RRhgl71
TZJmZMUmUyUntVV9NVim8GVHMyDcYQ==
=3uTU
-----END PGP SIGNATURE-----
Merge tag 'topic/hdcp-2018-02-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
Add HDCP support to i915 drm driver.
* tag 'topic/hdcp-2018-02-13' of git://anongit.freedesktop.org/drm/drm-misc: (26 commits)
drm/i915: fix misalignment in HDCP register def
drm/i915: Reauthenticate HDCP on failure
drm/i915: Detect panel's hdcp capability
drm/i915: Optimize HDCP key load
drm/i915: Retry HDCP bksv read
drm/i915: Connector info in HDCP debug msgs
drm/i915: Stop encryption for repeater with no sink
drm/i915: Handle failure from 2nd stage HDCP auth
drm/i915: Downgrade hdcp logs from INFO to DEBUG_KMS
drm/i915: Restore HDCP DRM_INFO when with no downstream
drm/i915: Check for downstream topology errors
drm/i915: Start repeater auth on READY/CP_IRQ
drm/i915: II stage HDCP auth for repeater only
drm/i915: Extending HDCP for HSW, BDW and BXT+
drm/i915/dp: Fix compilation of intel_dp_hdcp_check_link
drm/i915: Only disable HDCP when it's active
drm/i915: Don't allow HDCP on PORT E/F
drm/i915: Implement HDCP for DisplayPort
drm/i915: Implement HDCP for HDMI
drm/i915: Add function to output Aksv over GMBUS
...
Now let's finish the Port-F support by adding the
proper port F detection, irq and power well support.
v2: Rebase
v3: Use BIT_ULL
v4: Cover missed case on ddi init.
v5: Update commit message.
v6: Rebase on top of display headers rework.
v7: Squash power-well handling related to DDI F to this
patch to avoid warns as pointed out by DK.
v8: Introduce DDI_F_LANES to PG2. (DK)
v9: Squash in the PORT_F case for enabling DP MST encoder. (DK)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-9-rodrigo.vivi@intel.com
Apparently SKL/KBL/CFL need some manual help to get the
programmed HDMI vswing to stick. Implement the relevant
workaround (display w/a #1143).
Note that the relevant chicken bits live in a transcoder register
even though the bits affect a specific DDI port rather than a
specific transcoder. Hence we must pick the correct transcoder
register instance based on the port rather than based on the
cpu_transcoder.
Also note that for completeness I included support for DDI A/E
in the code even though we never have HDMI on those ports.
v2: CFL needs the w/a as well (Rodrigo and Art)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122174131.28046-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This patch adds HDCP support for HDMI connectors by implementing
the intel_hdcp_shim.
Nothing too special, just a bunch of DDC reads/writes.
Changes in v2:
- Rebased on drm-intel-next
Changes in v3:
- Initialize new worker
Changes in v4:
- Remove SKL_ prefix from most register names (Daniel)
- Wrap sanity checks in WARN_ON (Daniel)
- Consolidate the enable/disable functions into one toggle fn
- Use intel_hdcp_init (Daniel)
Changes in v5:
- checkpatch whitespace nits
Changes in v6:
- None
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180108195545.218615-9-seanpaul@chromium.org
This patch adds the framework required to add HDCP support to intel
connectors. It implements Aksv loading from fuse, and parts 1/2/3
of the HDCP authentication scheme.
Note that without shim implementations, this does not actually implement
HDCP. That will come in subsequent patches.
Changes in v2:
- Don't open code wait_fors (Chris)
- drm_hdcp.c under MIT license (Daniel)
- Move intel_hdcp_disable() call above ddi_disable (Ram)
- Fix // comments (I wore a cone of shame for 12 hours to atone) (Daniel)
- Justify intel_hdcp_shim with comments (Daniel)
- Fixed async locking issues by adding hdcp_mutex (Daniel)
- Don't alter connector_state in enable/disable (Daniel)
Changes in v3:
- Added hdcp_mutex/hdcp_value to make async reasonable
- Added hdcp_prop_work to separate link checking & property setting
- Added new helper for atomic_check state tracking (Daniel)
- Moved enable/disable into atomic_commit with matching helpers
- Moved intel_hdcp_check_link out of all locks when called from dp
- Bumped up ksv_fifo timeout (noticed failure on one of my dongles)
Changes in v4:
- Remove SKL_ prefix from most register names (Daniel)
- Move enable/disable back to modeset path (Daniel)
- s/get_random_long/get_random_u32/ (Daniel)
- Remove mode_config.mutex lock in prop_work (Daniel)
- Add intel_hdcp_init to handle init of conn components (Daniel)
- Actually check return value of attach_property
- Check Bksv is valid before trying to authenticate (Ram)
Changes in v5:
- checkpatch whitespace changes
- s/DRM_MODE_CONTENT_PROTECTION_OFF/DRM_MODE_CONTENT_PROTECTION_UNDESIRED/
- Fix ksv list wait timeout (actually wait 5s)
- Increase the R0 timeout to 300ms (Ram)
Changes in v6:
- SPDX license
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ramalingam C <ramalingm.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180108195545.218615-6-seanpaul@chromium.org
drivers/gpu/drm/i915/intel_ddi.c:2098 intel_ddi_clk_select() warn: inconsistent indenting
References: 8edcda1266 ("drm/i915: Protect DDI port to DPLL map from theoretical race.")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171219112649.9388-1-chris@chris-wilson.co.uk
In case we have multiple modesets for different connectors
happening in parallel we could have a race on the RMW on these
shared registers.
This possibility was initially raised by Paulo when reviewing
commit '555e38d27317 ("drm/i915/cnl: DDI - PLL mapping")'
but the original possibility comes from commit '5416d871136d
("drm/i915/skl: Set the eDP link rate on DPLL0")'. Or maybe
later when atomic commits entered into picture.
Apparently the discussion around this topic showed that the
right solution would be on serializing the atomic commits in
a way that we don't have the possibility of races here since
if that parallel modeset happenings apparently many other
things will be on fire.
Code is there since SKL and there was no report of issue,
but since we never looked back to that serialization possibility,
and also we don't have an igt case for that it is better to at
least protect this corner.
Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Fixes: 555e38d273 ("drm/i915/cnl: DDI - PLL mapping")
Fixes: 5416d87113 ("drm/i915/skl: Set the eDP link rate on DPLL0")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst maarten.lankhorst@linux.intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst maarten.lankhorst@linux.intel.com
Link: https://patchwork.freedesktop.org/patch/msgid/20171215224310.19103-1-rodrigo.vivi@intel.com
Without masking out the old value, we can end up pointing the DDI to a
disabled PLL, which makes the system fall over. Mask out the previous
value before setting the PLL to DDI mapping.
This can be observed by running igt/testdisplay with both an eDP and
HDMI/DP output active.
v2: Add the Bugzilla link
Fixes: 555e38d273 ("drm/i915/cnl: DDI - PLL mapping")
Testcase: igt/testdisplay
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103997
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171201021700.13504-1-james.ausmus@intel.com
Transcoder EDP does not support audio. Let's not try to
read the state of the audio enable bit HSW_AUD_PIN_ELD_CP_VLD
based on the pipe when using transcoder EDP.
While at it make the function static and flatten it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129164303.18793-3-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
