This patch adds a new port attribute - IFLA_BRPORT_BACKUP_PORT, which
allows to set a backup port to be used for known unicast traffic if the
port has gone carrier down. The backup pointer is rcu protected and set
only under RTNL, a counter is maintained so when deleting a port we know
how many other ports reference it as a backup and we remove it from all.
Also the pointer is in the first cache line which is hot at the time of
the check and thus in the common case we only add one more test.
The backup port will be used only for the non-flooding case since
it's a part of the bridge and the flooded packets will be forwarded to it
anyway. To remove the forwarding just send a 0/non-existing backup port.
This is used to avoid numerous scalability problems when using MLAG most
notably if we have thousands of fdbs one would need to change all of them
on port carrier going down which takes too long and causes a storm of fdb
notifications (and again when the port comes back up). In a Multi-chassis
Link Aggregation setup usually hosts are connected to two different
switches which act as a single logical switch. Those switches usually have
a control and backup link between them called peerlink which might be used
for communication in case a host loses connectivity to one of them.
We need a fast way to failover in case a host port goes down and currently
none of the solutions (like bond) cannot fulfill the requirements because
the participating ports are actually the "master" devices and must have the
same peerlink as their backup interface and at the same time all of them
must participate in the bridge device. As Roopa noted it's normal practice
in routing called fast re-route where a precalculated backup path is used
when the main one is down.
Another use case of this is with EVPN, having a single vxlan device which
is backup of every port. Due to the nature of master devices it's not
currently possible to use one device as a backup for many and still have
all of them participate in the bridge (which is master itself).
More detailed information about MLAG is available at the link below.
https://docs.cumulusnetworks.com/display/DOCS/Multi-Chassis+Link+Aggregation+-+MLAG
Further explanation and a diagram by Roopa:
Two switches acting in a MLAG pair are connected by the peerlink
interface which is a bridge port.
the config on one of the switches looks like the below. The other
switch also has a similar config.
eth0 is connected to one port on the server. And the server is
connected to both switches.
br0 -- team0---eth0
|
-- switch-peerlink
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new alternative store callback for port sysfs options
which takes a raw value (buf) and can use it directly. It is needed for the
backup port sysfs support since we have to pass the device by its name.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating various bridge objects in /sys/class/net/... make sure
that they belong to the container's owner instead of global root (if
they belong to a container/namespace).
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a new port flag - BR_ISOLATED. If it is set
then isolated ports cannot communicate between each other, but they can
still communicate with non-isolated ports. The same can be achieved via
ACLs but they can't scale with large number of ports and also the
complexity of the rules grows. This feature can be used to achieve
isolated vlan functionality (similar to pvlan) as well, though currently
it will be port-wide (for all vlans on the port). The new test in
should_deliver uses data that is already cache hot and the new boolean
is used to avoid an additional source port test in should_deliver.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now br_sysfs_if file flush doesn't have attr show. To read it will
cause kernel panic after users chmod u+r this file.
Xiong found this issue when running the commands:
ip link add br0 type bridge
ip link add type veth
ip link set veth0 master br0
chmod u+r /sys/devices/virtual/net/veth0/brport/flush
timeout 3 cat /sys/devices/virtual/net/veth0/brport/flush
kernel crashed with NULL a pointer dereference call trace.
This patch is to fix it by return -EINVAL when brport_attr->show
is null, just the same as the check for brport_attr->store in
brport_store().
Fixes: 9cf637473c ("bridge: add sysfs hook to flush forwarding table")
Reported-by: Xiong Zhou <xzhou@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bridge device doesn't generate any notifications upon vlan
modifications on itself because it doesn't use the generic bridge
notifications.
With the recent changes we know if anything was modified in the vlan config
thus we can generate a notification when necessary for the bridge device
so add support to br_ifinfo_notify() similar to how other combined
functions are done - if port is present it takes precedence, otherwise
notify about the bridge. I've explicitly marked the locations where the
notification should be always for the port by setting bridge to NULL.
I've also taken the liberty to rearrange each modified function's local
variables in reverse xmas tree as well.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new bridge port flag BR_NEIGH_SUPPRESS to
suppress arp and nd flood on bridge ports. It implements
rfc7432, section 10.
https://tools.ietf.org/html/rfc7432#section-10
for ethernet VPN deployments. It is similar to the existing
BR_PROXYARP* flags but has a few semantic differences to conform
to EVPN standard. Unlike the existing flags, this new flag suppresses
flood of all neigh discovery packets (arp and nd) to tunnel ports.
Supports both vlan filtering and non-vlan filtering bridges.
In case of EVPN, it is mainly used to avoid flooding
of arp and nd packets to tunnel ports like vxlan.
This patch adds netlink and sysfs support to set this bridge port
flag.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be able to transparently forward most link-local frames via
tunnels (e.g. vxlan, qinq). Currently the bridge's group_fwd_mask has a
mask which restricts the forwarding of STP and LACP, but we need to be able
to forward these over tunnels and control that forwarding on a per-port
basis thus add a new per-port group_fwd_mask option which only disallows
mac pause frames to be forwarded (they're always dropped anyway).
The patch does not change the current default situation - all of the others
are still restricted unless configured for forwarding.
We have successfully tested this patch with LACP and STP forwarding over
VxLAN and qinq tunnels.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for l2 multicast flood control was added in commit b6cb5ac833
("net: bridge: add per-port multicast flood flag"). It allows broadcast
as it was introduced specifically for unknown multicast flood control.
But as broadcast is a special case of multicast, this may also need to
be disabled. For this purpose, introduce a flag to disable the flooding
of received l2 broadcasts. This approach is backwards compatible and
provides flexibility in filtering for the desired packet types.
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Mike Manning <mmanning@brocade.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Implements an optional, per bridge port flag and feature to deliver
multicast packets to any host on the according port via unicast
individually. This is done by copying the packet per host and
changing the multicast destination MAC to a unicast one accordingly.
multicast-to-unicast works on top of the multicast snooping feature of
the bridge. Which means unicast copies are only delivered to hosts which
are interested in it and signalized this via IGMP/MLD reports
previously.
This feature is intended for interface types which have a more reliable
and/or efficient way to deliver unicast packets than broadcast ones
(e.g. wifi).
However, it should only be enabled on interfaces where no IGMPv2/MLDv1
report suppression takes place. This feature is disabled by default.
The initial patch and idea is from Felix Fietkau.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[linus.luessing@c0d3.blue: various bug + style fixes, commit message]
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I added the multicast flood control flag, I also added an attribute
for it for sysfs similar to other flags, but I forgot to add it to
brport_attrs.
Fixes: b6cb5ac833 ("net: bridge: add per-port multicast flood flag")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a per-port flag to control the unknown multicast flood, similar to the
unknown unicast flood flag and break a few long lines in the netlink flag
exports.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when we change the attributes of bridge or br_port by netlink,
a relevant netlink notification will be sent, but if we change them
by ioctl or sysfs, no notification will be sent.
We should ensure that whenever those attributes change internally or from
sysfs/ioctl, that a netlink notification is sent out to listeners.
Also, NetworkManager will use this in the future to listen for out-of-band
bridge master attribute updates and incorporate them into the runtime
configuration.
This patch is used for br_sysfs_if, and we also move br_ifinfo_notify out
of store_flag.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new argument to br_fdb_delete_by_port which allows to specify a
vid to match when flushing entries and use it in nbp_vlan_delete() to
flush the dynamically learned entries of the vlan/port pair when removing
a vlan from a port. Before this patch only the local mac was being
removed and the dynamically learned ones were left to expire.
Note that the do_all argument is still respected and if specified, the
vid will be ignored.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends the design in commit 958501163d ("bridge: Add support for
IEEE 802.11 Proxy ARP") with optional set of rules that are needed to
meet the IEEE 802.11 and Hotspot 2.0 requirements for ProxyARP. The
previously added BR_PROXYARP behavior is left as-is and a new
BR_PROXYARP_WIFI alternative is added so that this behavior can be
configured from user space when required.
In addition, this enables proxyarp functionality for unicast ARP
requests for both BR_PROXYARP and BR_PROXYARP_WIFI since it is possible
to use unicast as well as broadcast for these frames.
The key differences in functionality:
BR_PROXYARP:
- uses the flag on the bridge port on which the request frame was
received to determine whether to reply
- block bridge port flooding completely on ports that enable proxy ARP
BR_PROXYARP_WIFI:
- uses the flag on the bridge port to which the target device of the
request belongs
- block bridge port flooding selectively based on whether the proxyarp
functionality replied
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature is defined in IEEE Std 802.11-2012, 10.23.13. It allows
the AP devices to keep track of the hardware-address-to-IP-address
mapping of the mobile devices within the WLAN network.
The AP will learn this mapping via observing DHCP, ARP, and NS/NA
frames. When a request for such information is made (i.e. ARP request,
Neighbor Solicitation), the AP will respond on behalf of the
associated mobile device. In the process of doing so, the AP will drop
the multicast request frame that was intended to go out to the wireless
medium.
It was recommended at the LKS workshop to do this implementation in
the bridge layer. vxlan.c is already doing something very similar.
The DHCP snooping code will be added to the userspace application
(hostapd) per the recommendation.
This RFC commit is only for IPv4. A similar approach in the bridge
layer will be taken for IPv6 as well.
Signed-off-by: Kyeyoon Park <kyeyoonp@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, ports on the bridge are capable of automatic
discovery of nodes located behind the port. This is accomplished
via flooding of unknown traffic (BR_FLOOD) and learning the
mac addresses from these packets (BR_LEARNING).
If the above functionality is disabled by turning off these
flags, the port requires static configuration in the form
of static FDB entries to function properly.
This patch adds functionality to keep track of all ports
capable of automatic discovery. This will later be used
to control promiscuity settings.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turn the flag change macro into a function to allow
easier updates and to reduce space.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spaces required before the open parenthesis '(', before the open
brace '{', after that ',' and around that '?/:'.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a flag to control flood of unicast traffic. By default, flood is
on and the bridge will flood unicast traffic if it doesn't know
the destination. When the flag is turned off, unicast traffic
without an FDB will not be forwarded to the specified port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow user to control whether mac learning is enabled on the port.
By default, mac learning is enabled. Disabling mac learning will
cause new dynamic FDB entries to not be created for a particular port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
V3: make it a flag
V2: make the toggle per-port
Fast leave allows bridge to immediately stops the multicast
traffic on the port receives IGMP Leave when IGMP snooping is enabled,
no timeouts are observed.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
V2: make the toggle per-port
Fast leave allows bridge to immediately stops the multicast
traffic on the port receives IGMP Leave when IGMP snooping is enabled,
no timeouts are observed.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow an unpriviled user who has created a user namespace, and then
created a network namespace to effectively use the new network
namespace, by reducing capable(CAP_NET_ADMIN) and
capable(CAP_NET_RAW) calls to be ns_capable(net->user_ns,
CAP_NET_ADMIN), or capable(net->user_ns, CAP_NET_RAW) calls.
Allow setting bridge paramters via sysfs.
Allow all of the bridge ioctls:
BRCTL_ADD_IF
BRCTL_DEL_IF
BRCTL_SET_BRDIGE_FORWARD_DELAY
BRCTL_SET_BRIDGE_HELLO_TIME
BRCTL_SET_BRIDGE_MAX_AGE
BRCTL_SET_BRIDGE_AGING_TIME
BRCTL_SET_BRIDGE_STP_STATE
BRCTL_SET_BRIDGE_PRIORITY
BRCTL_SET_PORT_PRIORITY
BRCTL_SET_PATH_COST
BRCTL_ADD_BRIDGE
BRCTL_DEL_BRDIGE
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is Linux bridge implementation of root port guard.
If BPDU is received from a leaf (edge) port, it should not
be elected as root port.
Why would you want to do this?
If using STP on a bridge and the downstream bridges are not fully
trusted; this prevents a hostile guest for rerouting traffic.
Why not just use netfilter?
Netfilter does not track of follow spanning tree decisions.
It would be difficult and error prone to try and mirror STP
resolution in netfilter module.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is Linux bridge implementation of STP protection
(Cisco BPDU guard/Juniper BPDU block). BPDU block disables
the bridge port if a STP BPDU packet is received.
Why would you want to do this?
If running Spanning Tree on bridge, hostile devices on the network
may send BPDU and cause network failure. Enabling bpdu block
will detect and stop this.
How to recover the port?
The port will be restarted if link is brought down, or
removed and reattached. For example:
# ip li set dev eth0 down; ip li set dev eth0 up
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide macro to build sysfs data structures and functions
for accessing flag bits. If flag bits change do netlink
notification.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply restrictions on STP parameters based 802.1D 1998 standard.
* Fixes missing locking in set path cost ioctl
* Uses common code for both ioctl and sysfs
This is based on an earlier patch Sasikanth V but with overhaul.
Note:
1. It does NOT enforce the restriction on the relationship max_age and
forward delay or hello time because in existing implementation these are
set as independant operations.
2. If STP is disabled, there is no restriction on forward delay
3. No restriction on holding time because users use Linux code to act
as hub or be sticky.
4. Although standard allow 0-255, Linux only allows 0-63 for port priority
because more bits are reserved for port number.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Links for each port are created in sysfs using the device
name, but this could be changed after being added to the
bridge.
As well as being unable to remove interfaces after this
occurs (because userspace tools don't recognise the new
name, and the kernel won't recognise the old name), adding
another interface with the old name to the bridge will
cause an error trying to create the sysfs link.
This fixes the problem by listening for NETDEV_CHANGENAME
notifications and renaming the link.
https://bugzilla.kernel.org/show_bug.cgi?id=12743
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch allows the user to forcibly enable/disable ports as
having multicast routers attached. A port with a multicast router
will receive all multicast traffic.
The value 0 disables it completely. The default is 1 which lets
the system automatically detect the presence of routers (currently
this is limited to picking up queries), and 2 means that the port
will always receive all multicast traffic.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a 'hairpin' (also called 'reflective relay') mode
port configuration to the Linux Ethernet bridge kernel module.
A bridge supporting hairpin forwarding mode can send frames back
out through the port the frame was received on.
Hairpin mode is required to support basic VEPA (Virtual
Ethernet Port Aggregator) capabilities.
You can find additional information on VEPA here:
http://tech.groups.yahoo.com/group/evb/http://www.ieee802.org/1/files/public/docs2009/new-hudson-vepa_seminar-20090514d.pdfhttp://www.internet2.edu/presentations/jt2009jul/20090719-congdon.pdf
An additional patch 'bridge-utils: Add 'hairpin' port forwarding mode'
is provided to allow configuring hairpin mode from userspace tools.
Signed-off-by: Paul Congdon <paul.congdon@hp.com>
Signed-off-by: Anna Fischer <anna.fischer@hp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Holding rtnl_lock when we are unregistering the sysfs files can
deadlock if we unconditionally take rtnl_lock in a sysfs file. So fix
it with the now familiar patter of: rtnl_trylock and syscall_restart()
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kobject in the bridge code is only used for registering with sysfs,
not for any lifespan rules. This patch changes it to be only a pointer
and use the simpler api for this kind of thing.
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sysfs is now completely out of driver/module lifetime game. After
deletion, a sysfs node doesn't access anything outside sysfs proper,
so there's no reason to hold onto the attribute owners. Note that
often the wrong modules were accounted for as owners leading to
accessing removed modules.
This patch kills now unnecessary attribute->owner. Note that with
this change, userland holding a sysfs node does not prevent the
backing module from being unloaded.
For more info regarding lifetime rule cleanup, please read the
following message.
http://article.gmane.org/gmane.linux.kernel/510293
(tweaked by Greg to not delete the field just yet, to make it easier to
merge things properly.)
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The RSTP daemon needs to be able to flush all dynamic forwarding
entries in the case of topology change.
This is a temporary interface. It will change to a netlink interface
before RSTP daemon is officially released.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
This lets the network core have the ability to handle suspend/resume
issues, if it wants to.
Thanks to Frederik Deweerdt <frederik.deweerdt@gmail.com> for the arm
driver fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor how the bridge code interacts with kobject system.
It should still use kobjects even if not using sysfs.
Fix the error unwind handling in br_add_if.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: Use <linux/capability.h> where capable() is used.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kobject_add() and kobject_del() don't emit hotplug events anymore.
We need to do it ourselves now.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
