When creating address handle from multicast GID, set MAC according to
the appropriate formula instead of searching for it in the GID table:
- For IPv4 multicast GID use ip_eth_mc_map().
- For IPv6 multicast GID use ipv6_eth_mc_map().
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RoCEv2 Annex states that for RoCEv2 over IPv4, the corresponding
IPv4 address is encoded into the GID according to the following rule:
GID= :ffff:<IPv4 address>
Remove the 0xff0e prefix for RoCEv2 packets with IPv4 and leave it
zeroed and change rdma_is_multicast_addr() to consider the new logic.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RoCE Annex (A16.9.10/11) declares that during attach (detach) QP to a
multicast group, if the QP is associated with a RoCE port, the
multicast group MLID is unused and is ignored.
During attach or detach multicast, when the QP is associated with a
port, it is enough to check the port's link layer and validate the
LID only if it is Infiniband. Otherwise, avoid validating the
multicast LID.
Fixes: 8561eae60f ("IB/core: For multicast functions, verify that LIDs are multicast LIDs")
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add debugfs interface for monitor the number of delay drop timeout
events and the number of existing dropless RQs in the system.
In addition add debugfs interface for configuring the global timeout value
which is used in the SET_DELAY_DROP command.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RQs that were configured for "delay drop" will prevent packet drops
when their WQEs are depleted.
Marking an RQ to be drop-less is done by setting delay_drop_en in RQ
context using CREATE_RQ command.
Since this feature is globally activated/deactivated by using the
SET_DELAY_DROP command on all the marked RQs, we activated/deactivated
it according to the number of RQs with 'delay_drop' enabled.
When timeout is expired, then the feature is deactivated. Therefore
the driver handles the delay drop timeout event and reactivate it.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When a user sets port_guid, node_guid or policy of an IB virtual
function, save this information in "struct mlx5_vf_context".
This information will be restored later when pci_resume is called.
To make sure this works, one can use aer-inject to generate PCI
errors on mlx5 devices and verify if relevant fields are restored
after PCI resume.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds debug control parameters for congestion control which
can be read or written through debugfs. They are for reaction point and
notification point nodes.
These control parameters are as below:
+------------------------------+-----------------------------------------+
| Name | Description |
|------------------------------+-----------------------------------------|
|rp_clamp_tgt_rate | When set target rate is updated to |
| | current rate |
|------------------------------+-----------------------------------------|
|rp_clamp_tgt_rate_ati | When set update target rate based on |
| | timer as well |
|------------------------------+-----------------------------------------|
|rp_time_reset | time between rate increase if no |
| | CNP is received unit in usec |
|------------------------------+-----------------------------------------|
|rp_byte_reset | Number of bytes between rate inease if |
| | no CNP is received |
|------------------------------+-----------------------------------------|
|rp_threshold | Threshold for reaction point rate |
| | control |
|------------------------------+-----------------------------------------|
|rp_ai_rate | Rate for target rate, unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_hai_rate | Rate for hyper increase state |
| | unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_min_dec_fac | Minimum factor by which the current |
| | transmit rate can be changed when |
| | processing a CNP, unit is percerntage |
|------------------------------+-----------------------------------------|
|rp_min_rate | Minimum value for rate limit, |
| | unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_rate_to_set_on_first_cnp | Rate that is set when first CNP is |
| | received, unit is Mbps |
|------------------------------+-----------------------------------------|
|rp_dce_tcp_g | Used to calculate alpha |
|------------------------------+-----------------------------------------|
|rp_dce_tcp_rtt | Time between updates of alpha value, |
| | unit is usec |
|------------------------------+-----------------------------------------|
|rp_rate_reduce_monitor_period | Minimum time between consecutive rate |
| | reductions |
|------------------------------+-----------------------------------------|
|rp_initial_alpha_value | Initial value of alpha |
|------------------------------+-----------------------------------------|
|rp_gd | When CNP is received, flow rate is |
| | reduced based on gd, rp_gd is given as |
| | log2(rp_gd) |
|------------------------------+-----------------------------------------|
|np_cnp_dscp | dscp code point for generated cnp |
|------------------------------+-----------------------------------------|
|np_cnp_prio_mode | 802.1p priority for generated cnp |
|------------------------------+-----------------------------------------|
|np_cnp_prio | cnp priority mode |
+------------------------------+-----------------------------------------+
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The old logic ignored link state. This led to missing IB events like
when link goes down on the switch while admin state is up or to redundant
events like when admin state goes up while link is down.
To fix that, probe the port state on NETDEV events and compare to last
known state to decide if IB events needs to be dispatched.
FIxes: 5ec8c83e3a ("IB/mlx5: Port events in RoCE now rely on netdev events")
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently, unicast/multicast loopback raw ethernet
(non-RDMA) packets are sent back to the vport.
A unicast loopback packet is the packet with destination
MAC address the same as the source MAC address.
For multicast, the destination MAC address is in the
vport's multicast filter list.
Moreover, the local loopback is not needed if
there is one or none user space context.
After this patch, the raw ethernet unicast and multicast
local loopback are disabled by default. When there is more
than one user space context, the local loopback is enabled.
Note that when local loopback is disabled, raw ethernet
packets are not looped back to the vport and are forwarded
to the next routing level (eswitch, or multihost switch,
or out to the wire depending on the configuration).
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch allows driver to post send and receive
requests on QPs which are in error state.
Instead of flushing the QP in the context of polling
error CQEs, the QPs will be added to a flush list
maintained per CQ. QP state is moved to error.
QP is added to flush list if the user moves it
to error state using modify_qp also. After polling the HW
CQ in poll_cq routine, this flush list is traversed
and driver completes work requests on each QP in the flush
list, till the budget expires. The QP is moved out of
flush list during QP destroy or during modify_QP to RESET.
When ULPs post Work Requests while QP is in error state,
driver will store the ULP data and then increment the
QP producer s/w index, without ringing doorbell. It then
schedules a worker to invoke the CQ handler since the
interrupts wont be generated from the HW for this request.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Current implementation does not program vlan header insertion
in RoCE packet if no vlan is configured. Firmware does not add
prority when there is no vlan tag in the packet. Modify the code
to insert vlan header when PFC is enabled on the interface.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
All modules in drivers/infiniband defined and used MODULE_VERSION, which
was pointless because the kernel version describes their state more accurate
then those arbitrary numbers.
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Acked-by: Sagi Grimbrg <sagi@grimberg.me>
Reviewed-by: Sagi Grimberg <sagi@grimbeg.me>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Acked-by: Ram Amrani <Ram.Amrani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Adit Ranadive <aditr@vmware.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Logic of retrieving netdev speed from net_device and translating it to
IB speed is implemented in rxe, in usnic and in bnxt drivers.
Define new function which merges all.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Christian Benvenuti <benve@cisco.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is no need to return always zero for function which is not
supported. The IB stack treats uninitialized ib_device->functions as
not implemented.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RoCEv2 is the preferred RDMA protocol for Ethernet link layer because
of its advantages over RoCEv1. For better user experience make it the
default choice for RDMA_CM connections if device/port support it.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Constify static rxe_vm_ops that is never modified.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Its better to use __func__ to print functions name instead of writing
the name in the print statement.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use DEVICE_ATTR RO() macro and rename the show function accordingly.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Modify QP can fail and it can be acceptable, like when moving from RST to
ERR state, all the rest are not acceptable and a message to the log
should be printed.
The current code prints on all failures and many messages like:
"Failed to modify QP to ERROR state" appear, even when supported by the
state machine of the QP object.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The commit ebc9ca43e1 ("IB/core: Allow QP state transition from reset to error")
allowed transition from Reset to Error state for the QPs. This behavior
doesn't follow the IBTA specification 1.3, which in 10.3.1 QUEUE PAIR AND
EE CONTEXT STATES section.
The quote from the spec:
"An error can be forced from any state, except Reset, with
the Modify QP/EE Verb."
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
There is no need to assign "p" pointer twice.
This patch fixes the following smatch warning:
drivers/infiniband/ulp/ipoib/ipoib_cm.c:517 ipoib_cm_rx_handler() warn:
missing break? reassigning 'p->id'
Fixes: 839fcaba35 ("IPoIB: Connected mode experimental support")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Refactor error paths in ipoib_add_port() function. The code flow
ensures that the function terminates on every error flow and it makes
redundant all "else" cases.
The functions are called during the flow are returning "result < 0", in
case of error, so there is no need to check it explicitly.
Fixes: 58e9cc90cd ("IB/IPoIB: Fix bad error flow in ipoib_add_port()")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Update the multicast counter when multicast packets are received and
provide this information through ethtool support.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Set IPOIB_NEIGH_TBL_FLUSH bit after initializing the neighbor
flushed completion, otherwise the garbage collector may signal
a completion while it is not initialized yet.
Fixes: b63b70d877 ("IPoIB: Use a private hash table for path lookup in xmit path")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Don't allow negative values to max_nonsrq_conn_qp. There is no functional
impact on a negative value but it is logicically incorrect.
Fixes: 68e995a295 ("IPoIB/cm: Add connected mode support for devices without SRQs")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
While cleaning neighs and there is a send-only mcast neigh, the driver
should wait to finish its join process before trying to remove it.
Without this patch, we will see messages like: "ipoib_mcast_leave on an
in-flight join" and unexpected results in the join_complete.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The work mcast_task can re-queue itself, so instead of doing
cancel && flush_workqueue, that still can leave a queued task
on the air, use cancel_delayed_work_sync.
Also, no need to use lock over the cancel, the original lock was
due to bit assignment setting (IPOIB_MCAST_RUN) that is not in use
anymore.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
A potential race between light_event and interface restart
may attach multicast group to an already attached QP.
Scenario:
light_event flow goes through ipoib_mcast_dev_flush function,
if a context switch occurs before calling ipoib_mcast_remove_list,
then we may face a situation where the broadcast of the priv is null
and the corresponding QP is not detached yet.
If an "interface restart" runs during the previous context switch,
the following scenario occurs:
When the device goes up, ipoib_ib_dev_up function will be called,
it will send a new registration request to the broadcast group and then
attach the group to the QP that was not detached before.
IPOIB_FLUSH_LIGHT INTERFACE RESTART
__ipoib_ib_dev_flush |
| |
| |
| |
ipoib_mcast_dev_flush |
Move mcast list and broadcast to remove_list |
| |
| |
Context Switch--> |
| ipoib_ib_dev_down
| |
| |
| ipoib_ib_dev_up
| |
| |
| ipoib_mcast_join_task
| allocate new broadcast
| |
| |
| Attach QP to multicast group
| |
| |
| <--Context Switch
ipoib_mcast_leave
Detach QP from multicast group
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Initialize the port_num for iWARP in rdma_init_qp_attr.
Fixes: 5ecce4c9b17b("Check port number supplied by user verbs cmds")
Cc: <stable@vger.kernel.org> # v2.6.14+
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The port number is only valid if IB_QP_PORT is set in the mask.
So only check port number if it is valid to prevent modify_qp from
failing due to an invalid port number.
Fixes: 5ecce4c9b17b("Check port number supplied by user verbs cmds")
Cc: <stable@vger.kernel.org> # v2.6.14+
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We might get some bogus error completions in case the target will
remotely invalidate the rkey and the HCA will need to retransmit
from this buffer.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If we modified the qp to ERROR state, and
drained the recieve queue, post_recv must
trigger the responder task to complete
the drain work request.
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Vijay Immanuel <vijayi@attalasystems.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>--
Signed-off-by: Doug Ledford <dledford@redhat.com>
Wrap ib_copy_to_udata with a function that ensures that the data
being copied over to user space isn't longer than the allowed.
Fixes: cecbcddf64 ("qedr: Add support for QP verbs")
Fixes: a7efd7773e ("qedr: Add support for PD,PKEY and CQ verbs")
Fixes: ac1b36e55a ("qedr: Add support for user context verbs")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Only use the read sge lkey/addr and the remote rkey/addr if the
length of the read is not zero. Otherwise the read response might
be treated as the RTR read response and not delivered to the
application. Or worse Terminator hardware will fail a 0B read
if the STAG is 0 even if the read length is 0.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
CM REQs cannot be successfully retried, because a new pv_cm_id is
created for each request, without checking if one already exists.
By checking if an id exists before creating one, the bug is fixed.
This bug can be provoked by running an RDMA CM user-land application,
but inserting a five seconds delay before the rdma_accept() call on
the passive side. This delay is larger than the default CMA timeout,
and triggers a retry from the active side. The retried REQ will use
another pv_cm_id (the cm_id on the wire). This confuses the CM
protocol and two REJs are sent from the passive side.
Here is an excerpt from ibdump running without the patch:
3.285092 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
7.382711 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
7.382861 LID: 4 -> LID: 4 InfiniBand 290 CM: ConnectReject
7.387644 LID: 4 -> LID: 4 InfiniBand 290 CM: ConnectReject
and here is the same with bug fix applied:
3.251010 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
7.349387 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
8.258443 LID: 4 -> LID: 4 SDP 290 CM: ConnectReply(SDP Hello)
8.259890 LID: 4 -> LID: 4 InfiniBand 290 CM: ReadyToUse
Suggested-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reported-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Tested-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Current computation of qp->timeout_jiffies in rvt_modify_qp() will cause
overflow due to the fact that the input to the function usecs_to_jiffies
is only 32-bit ( unsigned int). Overflow will occur when attr->timeout is
equal to or greater than 30. The consequence is unnecessarily excessive
retry and thus degradation of the system performance.
This patch fixes the problem by limiting the input to 5-bit and calling
usecs_to_jiffies() before multiplying the scaling factor.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Local ack delay exposed by the driver is 0 which means infinite QP
timeout. Reporting the default value to 16 (approx 260ms)
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
While invoking the req_notify_cq hook, ULPs can request
whether the CQs have any CQEs pending. If CQEs are pending,
drivers can indicate it by returning 1 for req_notify_cq.
The stack will poll CQ again till CQ is empty.
This patch peeks the CQ for any valid entries and return accordingly.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix the incorrect reporting of number of polled
entries by taking into account the max CQ depth
in the driver.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Driver shall check if the host system bios has enabled
Atomic operations capability in PCI Device Control 2
register of the pci-device. Expose the ATOMIC_HCA
flag only if the Atomic operations capability is set.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Starting FW version 20.6.47, firmware is keeping separate statistics
for L2 and RDMA. However, driver needs to specify RDMA or not when
allocating stat_ctx.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There's a couple of bugs in the support of max_rd_atomic and
max_dest_rd_atomic. In the modify_qp, if the requested max_rd_atomic,
which is the ORRQ size, is greater than what the chip can support,
then we have to cap the request to chip max as we can't have the HW
overflow the ORRQ. Capping the max_rd_atomic support internally is okay
to do as the remaining read/atomic WRs will still be sitting in the SQ.
However, for the max_dest_rd_atomic, the driver has to error out as
this dictates the IRRQ size and we can't control what the remote
side sends.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- Report supported value for max_mr_size to IB stack in query_device.
Also, check and log if MR size requested by application in
reg_user_mr() is greater than value currently supported by driver.
- Report only 4K page size support for now
- Fix Max_QP value returned by ibv_devinfo -vv.
In case of PF, FW reserves 129 QPs for creating QP1s of VFs
and PF. So the max_qp value reported by FW for PF doesn'tt include
the QP1. Fixing this issue by adding 1 with the value reported
by FW.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This fix is added only to avoid system crash in some a
specific scenario. When bnxt_re driver is loaded and if
user tries to change interface mac address, delete GID
fails because QP1 is still associated with existing MAC
(default GID). If the above command fails GID tables are
not modified in the h/w or driver, but the GID context memory
is freed. Now, if the user changes the mac back to the original
value, another add_gid comes to the driver where the driver
reports that the GID is already present in its table
and tries to access the context which was already freed.
So, in this case, in order to avoid NULL pointer de-reference,
this patch removes the context memory free if delete_gid fails
and the same context memory is re-used in new add_gid.
Memory cleanup will be taken care during driver unload, while
deleting the GID table.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Posting WQE size of 2 results in a WQE_FORMAT_ERROR
thrown by the HW as it requires host to supply WQE Size with room
for atleast one SGE so that the resulting WQE size be atleast 3.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The driver must free the DPI during the dealloc_ucontext
instead of freeing it during dealloc_pd. However, the DPI
allocation scheme remains unchanged.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
"umem" is a valid pointer. We intended to print "*umem" or even just
"err" instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If either of these allocations fail then we return ERR_PTR(0). That's
equivalent to NULL and results in a NULL pointer dereference in the
caller.
Fixes: fe2caefcdf ("RDMA/ocrdma: Add driver for Emulex OneConnect IBoE RDMA adapter")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We should preserve the original "status" error code instead of resetting
it to zero. Returning ERR_PTR(0) is the same as NULL and results in a
NULL dereference in the callers. I added a printk() on error instead.
Fixes: 45e86b33ec ("RDMA/ocrdma: Cache recv DB until QP moved to RTR")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We accidentally don't set the error code on some error paths. It means
return ERR_PTR(0) which is NULL and results in a NULL dereference in the
caller.
Fixes: 13a239330a ("RDMA/cxgb3: Don't ignore insert_handle() failures")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If one of these kmalloc() calls fails then we return ERR_PTR(0) which is
NULL. It results in a NULL dereference in the callers.
Fixes: cfdda9d764 ("RDMA/cxgb4: Add driver for Chelsio T4 RNIC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We accidentally forgot to set the error code if ib_copy_from_udata()
fails. It means we return ERR_PTR(0) which is NULL and results in a
NULL dereference in the callers.
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We accidentally don't see the error code on some of these error paths.
It means we return ERR_PTR(0) which is NULL and it results in a NULL
dereference in the caller.
This bug dates to pre-git days.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the physical buffer list entries (PBLEs) of a QP are freed
up at i40iw_dereg_mr, they can be assigned to a newly
created QP before the previous QP is destroyed. Fix this
by freeing PBLEs only when the QP is destroyed.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Control Queue Pair (CQP) request objects, which have
not received a completion upon interface close, remain
in memory.
To fix this, identify and free all pending CQP request
objects during destroy CQP OP.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To avoid infinite loop, in i40iw_ieq_handle_exception, update
plist inside while loop.
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add missing write memory barrier before writing the
header containing valid bit to the WQE in i40iw_puda_send.
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Current flow leaves software QP structures in memory if
Control Queue Pair (CQP) destroy QP OP fails. To fix this,
free QP resources on fail of CQP destroy QP OP.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
On PCI function reset, cm_id reference is not released
which causes an application hang, as it waits on the
cm_id to be released on rdma_destroy.
To fix this, call i40iw_cm_disconn during a PCI function
reset to clean-up resources and release cm_id reference.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Utilize iwdev->reset on a PCI function reset notification
instead of passing in reset flag for resource clean-up.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Control Queue Pair (CQP) OPs, in this case - Update SDs,
cannot poll the Control Completion Queue (CCQ) after CCQ is
destroyed. Instead, poll via registers.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The order for calling i40iw_destroy_pble_pool is incorrect.
Also, add PBLE_CHUNK_MEM init state to track pble pool
creation and destruction.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Playing with IP-O-IB interface can trigger a warning message:
"ib0: Failed to modify QP to ERROR state" to be logged.
This happens when the QP is in IB_QPS_RESET state and the stack
is trying to transition it to IB_QPS_ERR state in ipoib_ib_dev_stop().
According to the IB spec, Table 91 - "QP State Transition Properties"
it looks like the transition from reset to error is valid:
Transition: Any State to Error
Required Attributes: None
Optional Attributes: None allowed
Actions: Queue processing is stopped. Work Requests pending or in
process are completed in error, when possible.
This patch allows the transition and quiets the message.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch correct the comment style warnings caught by
checkpatch.pl script.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When modified the MAC address used hns_roce_mac function, we release and create
reserved qp again, It is not necessary to use spin_lock_bh and spin_unlock_bh in
handle_en_event, Otherwise, it will occur a error. This patch mainly fixes it.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When opcode of work request is RDMA read and write, it
should use rdma_wr to get remote_addr and rkey. This
patch fixes it.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When destroyed rc qp, the hr_qp will be used after freed. This patch
will fix it.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In hip06 SoC, RoCE driver creates 8 reserved loopback QPs to
ensure zero wqe when free mr. However, if the enabled phy
port number is less than 6, it will fail in polling cqe with
8 reserved loopback QPs.
In order to solve this problem, the number of loopback Qps
will be adjusted based on the number of enabled phy port.
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The driver checks if the lower level driver supports get_stats, and if
so calls it to get the updated statistics, otherwise takes from the
current netdevice stats object.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently the RoCE GID management uses the ib_wq to do add and delete new GIDs
according to the netdev events.
The ib_wq isn't an ordered workqueue and thus two work elements can be executed
concurrently which will result in unexpected behavior and inconsistency of the
GIDs cache content.
Example:
ifconfig eth1 11.11.11.11/16 up
This command will invoke the following netdev events in the following order:
1. NETDEV_UP
2. NETDEV_DOWN
3. NETDEV_UP
If (2) and (3) will be executed concurrently or in reverse order, instead of
having a new GID with 11.11.11.11 IP, we will end up without any new GIDs.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The failure in creation of debugfs entries for mr_cache left entries,
which were already created.
It caused to mismatch and misguiding for the end users. The solution
is to clean mr_cache debugfs root, so no leftovers will be in the
system. In addition, let's document why the error is not needed to be
forwarded to user in case of failure.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The caller to the driver marks GFP_NOIO allocations with help
of memalloc_noio-* calls now. This makes redundant to pass down
to the driver gfp flags, which can be GFP_KERNEL only.
The patch removes the gfp flags argument and updates all driver paths.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The caller to the driver marks GFP_NOIO allocations with help
of memalloc_noio-* calls now. This makes redundant to pass down
to the driver gfp flags, which can be GFP_KERNEL only.
The patch removes the gfp flags argument and updates all driver paths.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Commit 21caf2fc19 ("mm: teach mm by current context info to not do I/O
during memory allocation") added the memalloc_noio_(save|restore) functions
to enable people to modify the MM behavior by disabling I/O during memory
allocation. This was further extended in Fixes: 934f3072c1 ("mm: clear
__GFP_FS when PF_MEMALLOC_NOIO is set"). memalloc_noio_* functions prevent
allocation paths recursing back into the filesystem without explicitly
changing the flags for every allocation site.
However the IPoIB hasn't been keeping up with the changes and missed
completely these memalloc_noio_* calls. This led to update of
allocation site with special QP creation flag, see commit 09b93088d7
("IB: Add a QP creation flag to use GFP_NOIO allocations"), while this
flag is supported by small number of drivers in IB stack.
Let's change it by updating to memalloc_noio_* calls and allow
for every driver underneath enjoy NOIO allocations.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch checks if there is a driver below that
needs to be updated on the new MTU and calls it
accordingly.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The msleep(1) may do not sleep 1 ms as expected
and will sleep longer. The simple conversion from
msleep to usleep_range between 1ms and 2ms can solve an
issue.
The full and comprehensive explanation can be found at [1] and [2].
[1] https://lkml.org/lkml/2007/8/3/250
[2] Documentation/timers/timers-howto.txt
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch makes use of IB core's ib_modify_qp_with_udata function that
also resolves the DMAC and handles udata.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds new function ib_modify_qp_with_udata so that
uverbs layer can avoid handling L2 mac address at verbs layer
and depend on the core layer to resolve the mac address consistently
for all required QPs.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When resolving an IP address that is on the host of the caller the
result from querying the routing table is the loopback device. This is
not a valid response, because it doesn't represent the RDMA device and
the port.
Therefore, callers need to check the resolved device and if it is a
loopback device find an alternative way to resolve it. To avoid this we
make sure that the response from rdma_resolve_ip() will not be the
loopback device.
While that, we fix an static checker warning about dereferencing an
unintitialized pointer using the same solution as in commit abeffce90c
("net/mlx5e: Fix a -Wmaybe-uninitialized warning") as a reference.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In function addr_resolve() the namespace is a required input parameter
and not an output. It is passed later for searching the routing table
and device addresses. Also, it shouldn't be copied back to the caller.
Fixes: 565edd1d55 ('IB/addr: Pass network namespace as a parameter')
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Under heavy iser target(scst) start/stop stress during login/logout
on iser intitiator side happened trace call provided below.
The function iscsi_iser_slave_alloc iser_conn pointer could be NULL,
due to the fact that function iscsi_iser_conn_stop can be called before
and free iser connection. Let's protect that flow by introducing global mutex.
BUG: unable to handle kernel paging request at 0000000000001018
IP: [<ffffffffc0426f7e>] iscsi_iser_slave_alloc+0x1e/0x50 [ib_iser]
Call Trace:
? scsi_alloc_sdev+0x242/0x300
scsi_probe_and_add_lun+0x9e1/0xea0
? kfree_const+0x21/0x30
? kobject_set_name_vargs+0x76/0x90
? __pm_runtime_resume+0x5b/0x70
__scsi_scan_target+0xf6/0x250
scsi_scan_target+0xea/0x100
iscsi_user_scan_session.part.13+0x101/0x130 [scsi_transport_iscsi]
? iscsi_user_scan_session.part.13+0x130/0x130 [scsi_transport_iscsi]
iscsi_user_scan_session+0x1e/0x30 [scsi_transport_iscsi]
device_for_each_child+0x50/0x90
iscsi_user_scan+0x44/0x60 [scsi_transport_iscsi]
store_scan+0xa8/0x100
? common_file_perm+0x5d/0x1c0
dev_attr_store+0x18/0x30
sysfs_kf_write+0x37/0x40
kernfs_fop_write+0x12c/0x1c0
__vfs_write+0x18/0x40
vfs_write+0xb5/0x1a0
SyS_write+0x55/0xc0
Fixes: 318d311e8f ("iser: Accept arbitrary sg lists mapping if the device supports it")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Vladimir Neyelov <vladimirn@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimbeg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
While looking into Coverity ID 1351047 I ran into the following
piece of code at
drivers/infiniband/core/verbs.c:496:
ret = rdma_addr_find_l2_eth_by_grh(&dgid, &sgid,
ah_attr->dmac,
wc->wc_flags & IB_WC_WITH_VLAN ?
NULL : &vlan_id,
&if_index, &hoplimit);
The issue here is that the position of arguments in the call to
rdma_addr_find_l2_eth_by_grh() function do not match the order of
the parameters:
&dgid is passed to sgid
&sgid is passed to dgid
This is the function prototype:
int rdma_addr_find_l2_eth_by_grh(const union ib_gid *sgid,
const union ib_gid *dgid,
u8 *dmac, u16 *vlan_id, int *if_index,
int *hoplimit)
My question here is if this is intentional?
Answer:
Yes. ib_init_ah_from_wc() creates ah from the incoming packet.
Incoming packet has dgid of the receiver node on which this code is
getting executed and sgid contains the GID of the sender.
When resolving mac address of destination, you use arrived dgid as
sgid and use sgid as dgid because sgid contains destinations GID whom to
respond to.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
ib_map_mr_sg() can pass an SG-list to .map_mr_sg() that is larger
than what fits into a single MR. .map_mr_sg() must not attempt to
map more SG-list elements than what fits into a single MR.
Hence make sure that mlx5_ib_sg_to_klms() does not write outside
the MR klms[] array.
Fixes: b005d31647 ("mlx5: Add arbitrary sg list support")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Israel Rukshin <israelr@mellanox.com>
Cc: <stable@vger.kernel.org>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
As the code stands today the array access in remap_intr() is OK. To
future proof the code though we should explicitly check to ensure the
index value is not outside of the valid range. This is not a straight
forward calculation so err on the side of caution.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pull SCSI target updates from Nicholas Bellinger:
"It's been usually busy for summer, with most of the efforts centered
around TCMU developments and various target-core + fabric driver bug
fixing activities. Not particularly large in terms of LoC, but lots of
smaller patches from many different folks.
The highlights include:
- ibmvscsis logical partition manager support (Michael Cyr + Bryant
Ly)
- Convert target/iblock WRITE_SAME to blkdev_issue_zeroout (hch +
nab)
- Add support for TMR percpu LUN reference counting (nab)
- Fix a potential deadlock between EXTENDED_COPY and iscsi shutdown
(Bart)
- Fix COMPARE_AND_WRITE caw_sem leak during se_cmd quiesce (Jiang Yi)
- Fix TMCU module removal (Xiubo Li)
- Fix iser-target OOPs during login failure (Andrea Righi + Sagi)
- Breakup target-core free_device backend driver callback (mnc)
- Perform TCMU add/delete/reconfig synchronously (mnc)
- Fix TCMU multiple UIO open/close sequences (mnc)
- Fix TCMU CHECK_CONDITION sense handling (mnc)
- Fix target-core SAM_STAT_BUSY + TASK_SET_FULL handling (mnc + nab)
- Introduce TYPE_ZBC support in PSCSI (Damien Le Moal)
- Fix possible TCMU memory leak + OOPs when recalculating cmd base
size (Xiubo Li + Bryant Ly + Damien Le Moal + mnc)
- Add login_keys_workaround attribute for non RFC initiators (Robert
LeBlanc + Arun Easi + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (68 commits)
iscsi-target: Add login_keys_workaround attribute for non RFC initiators
Revert "qla2xxx: Fix incorrect tcm_qla2xxx_free_cmd use during TMR ABORT"
tcmu: clean up the code and with one small fix
tcmu: Fix possbile memory leak / OOPs when recalculating cmd base size
target: export lio pgr/alua support as device attr
target: Fix return sense reason in target_scsi3_emulate_pr_out
target: Fix cmd size for PR-OUT in passthrough_parse_cdb
tcmu: Fix dev_config_store
target: pscsi: Introduce TYPE_ZBC support
target: Use macro for WRITE_VERIFY_32 operation codes
target: fix SAM_STAT_BUSY/TASK_SET_FULL handling
target: remove transport_complete
pscsi: finish cmd processing from pscsi_req_done
tcmu: fix sense handling during completion
target: add helper to copy sense to se_cmd buffer
target: do not require a transport_complete for SCF_TRANSPORT_TASK_SENSE
target: make device_mutex and device_list static
tcmu: Fix flushing cmd entry dcache page
tcmu: fix multiple uio open/close sequences
tcmu: drop configured check in destroy
...
This fixes a over-read condition detected by FORTIFY_SOURCE for this
line:
memcpy(SKB_TO_PKT(skb), &ack_pkt, sizeof(skb->cb));
The error was:
In file included from ./include/linux/bitmap.h:8:0,
from ./include/linux/cpumask.h:11,
from ./include/linux/mm_types_task.h:13,
from ./include/linux/mm_types.h:4,
from ./include/linux/kmemcheck.h:4,
from ./include/linux/skbuff.h:18,
from drivers/infiniband/sw/rxe/rxe_resp.c:34:
In function 'memcpy',
inlined from 'send_atomic_ack.constprop' at drivers/infiniband/sw/rxe/rxe_resp.c:998:2,
inlined from 'acknowledge' at drivers/infiniband/sw/rxe/rxe_resp.c:1026:3,
inlined from 'rxe_responder' at drivers/infiniband/sw/rxe/rxe_resp.c:1286:10:
./include/linux/string.h:309:4: error: call to '__read_overflow2' declared with attribute error: detected read beyond size of object passed as 2nd parameter
__read_overflow2();
Daniel Micay noted that struct rxe_pkt_info is 32 bytes on 32-bit
architectures, but skb->cb is still 64. The memcpy() over-reads 32
bytes. This fixes it by zeroing the unused bytes in skb->cb.
Link: http://lkml.kernel.org/r/1497903987-21002-5-git-send-email-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Moni Shoua <monis@mellanox.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
max_fast_reg_page_list_len is only valid when the
memory management extentions are signaled by the underlying
driver.
Fix by adjusting iser_calc_scsi_params() to use
ISCSI_ISER_MAX_SG_TABLESIZE when the extentions are not indicated.
Reported-by: Thomas Rosenstein <thomas.rosenstein@creamfinance.com>
Fixes: Commit df749cdc45 ("IB/iser: Support up to 8MB data transfer in a single command")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Tested-by: Thomas Rosenstein <thomas.rosenstein@creamfinance.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pull security layer fixes from James Morris:
"Bugfixes for TPM and SELinux"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
IB/core: Fix static analysis warning in ib_policy_change_task
IB/core: Fix uninitialized variable use in check_qp_port_pkey_settings
tpm: do not suspend/resume if power stays on
tpm: use tpm2_pcr_read() in tpm2_do_selftest()
tpm: use tpm_buf functions in tpm2_pcr_read()
tpm_tis: make ilb_base_addr static
tpm: consolidate the TPM startup code
tpm: Enable CLKRUN protocol for Braswell systems
tpm/tpm_crb: fix priv->cmd_size initialisation
tpm: fix a kernel memory leak in tpm-sysfs.c
tpm: Issue a TPM2_Shutdown for TPM2 devices.
Add "shutdown" to "struct class".
This patch fixes a NULL pointer dereference in isert_login_recv_done()
of isert_conn->cm_id due to isert_cma_handler() -> isert_connect_error()
resetting isert_conn->cm_id = NULL during a failed login attempt.
As per Sagi, we will always see the completion of all recv wrs posted
on the qp (given that we assigned a ->done handler), this is a FLUSH
error completion, we just don't get to verify that because we deref
NULL before.
The issue here, was the assumption that dereferencing the connection
cm_id is always safe, which is not true since:
commit 4a579da258
Author: Sagi Grimberg <sagig@mellanox.com>
Date: Sun Mar 29 15:52:04 2015 +0300
iser-target: Fix possible deadlock in RDMA_CM connection error
As I see it, we have a direct reference to the isert_device from
isert_conn which is the one-liner fix that we actually need like
we do in isert_rdma_read_done() and isert_rdma_write_done().
Reported-by: Andrea Righi <righi.andrea@gmail.com>
Tested-by: Andrea Righi <righi.andrea@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Do not only report the state of the I/O context before srpt_abort_cmd()
was called but also the new state assigned by srpt_abort_cmd()
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
ib_get_cached_subnet_prefix can technically fail, but the only way it
could is not possible based on the loop conditions. Check the return
value before using the variable sp to resolve a static analysis warning.
-v1:
- Fix check to !ret. Paul Moore
Fixes: 8f408ab64b ("selinux lsm IB/core: Implement LSM notification
system")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Check the return value from get_pkey_and_subnet_prefix to prevent using
uninitialized variables.
Fixes: d291f1a652 ("IB/core: Enforce PKey security on QPs")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
- 2 Fixes for OPA found by debug kernel
- 1 Fix for user supplied input causing kernel problems
- 1 Fix for the IPoIB fixes submitted around -rc4
-----BEGIN PGP SIGNATURE-----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=JEor
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma update from Doug Ledford:
"This includes two bugs against the newly added opa vnic that were
found by turning on the debug kernel options:
- sleeping while holding a lock, so a one line fix where they
switched it from GFP_KERNEL allocation to a GFP_ATOMIC allocation
- a case where they had an isolated caller of their code that could
call them in an atomic context so they had to switch their use of a
mutex to a spinlock to be safe, so this was considerably more lines
of diff because all uses of that lock had to be switched
In addition, the bug that was discussed with you already about an out
of bounds array access in ib_uverbs_modify_qp and ib_uverbs_create_ah
and is only seven lines of diff.
And finally, one fix to an earlier fix in the -rc cycle that broke
hfi1 and qib in regards to IPoIB (this one is, unfortunately, larger
than I would like for a -rc7 submission, but fixing the problem
required that we not treat all devices as though they had allocated a
netdev universally because it isn't true, and it took 70 lines of diff
to resolve the issue, but the final patch has been vetted by Intel and
Mellanox and they've both given their approval to the fix).
Summary:
- Two fixes for OPA found by debug kernel
- Fix for user supplied input causing kernel problems
- Fix for the IPoIB fixes submitted around -rc4"
[ Doug sent this having not noticed the 4.12 release, so I guess I'll be
getting another rdma pull request with the actuakl merge window
updates and not just fixes.
Oh well - it would have been nice if this small update had been the
merge window one. - Linus ]
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/core, opa_vnic, hfi1, mlx5: Properly free rdma_netdev
RDMA/uverbs: Check port number supplied by user verbs cmds
IB/opa_vnic: Use spinlock instead of mutex for stats_lock
IB/opa_vnic: Use GFP_ATOMIC while sending trap
IPOIB is calling free_rdma_netdev even though alloc_rdma_netdev has
returned -EOPNOTSUPP.
Move free_rdma_netdev from ib_device structure to rdma_netdev structure
thus ensuring proper cleanup function is called for the rdma net device.
Fix the following trace:
ib0: Failed to modify QP to ERROR state
BUG: unable to handle kernel paging request at 0000000000001d20
IP: hfi1_vnic_free_rn+0x26/0xb0 [hfi1]
Call Trace:
ipoib_remove_one+0xbe/0x160 [ib_ipoib]
ib_unregister_device+0xd0/0x170 [ib_core]
rvt_unregister_device+0x29/0x90 [rdmavt]
hfi1_unregister_ib_device+0x1a/0x100 [hfi1]
remove_one+0x4b/0x220 [hfi1]
pci_device_remove+0x39/0xc0
device_release_driver_internal+0x141/0x200
driver_detach+0x3f/0x80
bus_remove_driver+0x55/0xd0
driver_unregister+0x2c/0x50
pci_unregister_driver+0x2a/0xa0
hfi1_mod_cleanup+0x10/0xf65 [hfi1]
SyS_delete_module+0x171/0x250
do_syscall_64+0x67/0x150
entry_SYSCALL64_slow_path+0x25/0x25
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
Pull security layer updates from James Morris:
- a major update for AppArmor. From JJ:
* several bug fixes and cleanups
* the patch to add symlink support to securityfs that was floated
on the list earlier and the apparmorfs changes that make use of
securityfs symlinks
* it introduces the domain labeling base code that Ubuntu has been
carrying for several years, with several cleanups applied. And it
converts the current mediation over to using the domain labeling
base, which brings domain stacking support with it. This finally
will bring the base upstream code in line with Ubuntu and provide
a base to upstream the new feature work that Ubuntu carries.
* This does _not_ contain any of the newer apparmor mediation
features/controls (mount, signals, network, keys, ...) that
Ubuntu is currently carrying, all of which will be RFC'd on top
of this.
- Notable also is the Infiniband work in SELinux, and the new file:map
permission. From Paul:
"While we're down to 21 patches for v4.13 (it was 31 for v4.12),
the diffstat jumps up tremendously with over 2k of line changes.
Almost all of these changes are the SELinux/IB work done by
Daniel Jurgens; some other noteworthy changes include a NFS v4.2
labeling fix, a new file:map permission, and reporting of policy
capabilities on policy load"
There's also now genfscon labeling support for tracefs, which was
lost in v4.1 with the separation from debugfs.
- Smack incorporates a safer socket check in file_receive, and adds a
cap_capable call in privilege check.
- TPM as usual has a bunch of fixes and enhancements.
- Multiple calls to security_add_hooks() can now be made for the same
LSM, to allow LSMs to have hook declarations across multiple files.
- IMA now supports different "ima_appraise=" modes (eg. log, fix) from
the boot command line.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (126 commits)
apparmor: put back designators in struct initialisers
seccomp: Switch from atomic_t to recount_t
seccomp: Adjust selftests to avoid double-join
seccomp: Clean up core dump logic
IMA: update IMA policy documentation to include pcr= option
ima: Log the same audit cause whenever a file has no signature
ima: Simplify policy_func_show.
integrity: Small code improvements
ima: fix get_binary_runtime_size()
ima: use ima_parse_buf() to parse template data
ima: use ima_parse_buf() to parse measurements headers
ima: introduce ima_parse_buf()
ima: Add cgroups2 to the defaults list
ima: use memdup_user_nul
ima: fix up #endif comments
IMA: Correct Kconfig dependencies for hash selection
ima: define is_ima_appraise_enabled()
ima: define Kconfig IMA_APPRAISE_BOOTPARAM option
ima: define a set of appraisal rules requiring file signatures
ima: extend the "ima_policy" boot command line to support multiple policies
...
Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpX4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymobgCfd0d13IfpZoq1N41wc6z2Z0xD7cwAnRMeH1/p
kEeISGpHPYP9f8PBh9FO
=Hfqt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
The ib_uverbs_create_ah() ind ib_uverbs_modify_qp() calls receive
the port number from user input as part of its attributes and assumes
it is valid. Down on the stack, that parameter is used to access kernel
data structures. If the value is invalid, the kernel accesses memory
it should not. To prevent this, verify the port number before using it.
BUG: KASAN: use-after-free in ib_uverbs_create_ah+0x6d5/0x7b0
Read of size 4 at addr ffff880018d67ab8 by task syz-executor/313
BUG: KASAN: slab-out-of-bounds in modify_qp.isra.4+0x19d0/0x1ef0
Read of size 4 at addr ffff88006c40ec58 by task syz-executor/819
Fixes: 67cdb40ca4 ("[IB] uverbs: Implement more commands")
Fixes: 189aba99e7 ("IB/uverbs: Extend modify_qp and support packet pacing")
Cc: <stable@vger.kernel.org> # v2.6.14+
Cc: <security@kernel.org>
Cc: Yevgeny Kliteynik <kliteyn@mellanox.com>
Cc: Tziporet Koren <tziporet@mellanox.com>
Cc: Alex Polak <alexpo@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stats can be read from atomic context, hence make stats_lock as
a spinlock.
Fix the following trace with debug kernel.
BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:238
in_atomic(): 1, irqs_disabled(): 0, pid: 6487, name: sadc
Call Trace:
dump_stack+0x63/0x90
___might_sleep+0xda/0x130
__might_sleep+0x4a/0x90
mutex_lock+0x20/0x50
opa_vnic_get_stats64+0x56/0x140 [opa_vnic]
dev_get_stats+0x74/0x130
dev_seq_printf_stats+0x37/0x120
dev_seq_show+0x14/0x30
seq_read+0x26d/0x3d0
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pass GFP_ATOMIC flag to ib_create_send_mad() while sending trap as it
can be triggered from the atomic context.
Fix the following trace with debug kernel.
BUG: sleeping function called from invalid context at mm/slab.h:432
in_atomic(): 1, irqs_disabled(): 0, pid: 1771, name: NetworkManager
Call Trace:
dump_stack+0x63/0x90
___might_sleep+0xda/0x130
__might_sleep+0x4a/0x90
__kmalloc+0x19e/0x220
? ib_create_send_mad+0xea/0x390 [ib_core]
ib_create_send_mad+0xea/0x390 [ib_core]
opa_vnic_vema_send_trap+0x17b/0x460 [opa_vnic]
opa_vnic_vema_report_event+0x57/0x80 [opa_vnic]
opa_vnic_mac_send_event+0xaa/0xf0 [opa_vnic]
opa_vnic_set_rx_mode+0x17/0x30 [opa_vnic]
__dev_set_rx_mode+0x52/0x90
dev_set_rx_mode+0x26/0x40
__dev_open+0xe8/0x140
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Driver does not check whether proper configuration file exist in EPROM,
and treats empty partition as possible valid configuration, preventing
fallback to default firmware. Change EPROM read function to treat
missing magic number as read error.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Base receive contexts can be used by sub contexts. Because of this,
resources for the context cannot be completely freed until all sub
contexts are done using the base context.
Introduce a reference count so that the base receive context can be
freed only when all sub contexts are done with it.
Use the provided function call for setting default send context
integrity rather than the manual method.
The cleanup path does not set all variables back to NULL after freeing
resources. Since the clean up code can get called more than once,
(e.g. during context close and on the error path), it is necessary to
make sure that all the variables are NULLed.
Possible crash are:
BUG: unable to handle kernel paging request at 0000000001908900
IP: read_csr+0x24/0x30 [hfi1]
RIP: 0010:read_csr+0x24/0x30 [hfi1]
Call Trace:
sc_disable+0x40/0x110 [hfi1]
hfi1_file_close+0x16f/0x360 [hfi1]
__fput+0xe7/0x210
____fput+0xe/0x10
or
kernel BUG at mm/slub.c:3877!
RIP: 0010:kfree+0x14f/0x170
Call Trace:
hfi1_free_ctxtdata+0x19a/0x2b0 [hfi1]
? hfi1_user_exp_rcv_grp_free+0x73/0x80 [hfi1]
hfi1_file_close+0x20f/0x360 [hfi1]
__fput+0xe7/0x210
____fput+0xe/0x10
Fixes: Commit 62239fc6e5 ("IB/hfi1: Clean up on context initialization failure")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The expected receive lists (tid_xxx_list) are not initialized until
late in the receive context initialization. If an error happens
before the initialization, a NULL pointer access will occur during
cleanup.
Initialized the lists sooner rather than later to avoid this Oops:
IP: unlock_exp_tids.isra.11+0x26/0xd0 [hfi1]
RIP: 0010:unlock_exp_tids.isra.11+0x26/0xd0 [hfi1]
Call Trace:
hfi1_user_exp_rcv_free+0x79/0xb0 [hfi1]
hfi1_file_close+0x87/0x360 [hfi1]
__fput+0xe7/0x210
____fput+0xe/0x10
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
pci_enable_msix_range() and pci_disable_msix() have been deprecated.
Updating to the new pci_alloc_irq_vectors() interface.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds a trace for putting a TID and
for writing the RcvArray CSR.
The CSR access template can be easily extended for additional
CSR readq/writeq calls.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This is the preferred way to add a duplicate trace call.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently, platform configuration can be read from EFI variable
for discrete cards. It will happen when reading from EPROM fails.
EFI variables should not be queried for platform configuration
in any scenario.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Declarations and code in common between verbs and PSM are now moved
to exp_rcv.[ch].
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Change QSFP cable error events logging levels from info to error.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix info array of host message flags by adding entry
for link width downgrade and reverse values for
BC SMA and BC PWR_MSG messages
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Bartlomiej Dudek <bartlomiej.dudek@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
According to IBTA spec a QKey violation should not result in a bad qkey
trap being triggered for UD queue pairs. Also since it is a silent error
we do not increment the q_key violation or the dropped packet counters.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ensure states returned to the Fabric Manager are consistent with
the OPA specification by caching the physical state along with the
logical state.
Reviewed-by: Stuart Summers <john.s.summers@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Andrzej Kotlowski <andrzej.kotlowski@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Playing with IP-O-IB interface can trigger a warning message:
"ib0: Failed to modify QP to ERROR state" to be logged.
This happens when the QP is in IB_QPS_RESET state and the stack
is trying to transition it to IB_QPS_ERR state in ipoib_ib_dev_stop().
According to the IB spec, Table 91 - "QP State Transition Properties"
it looks like the transition from reset to error is valid:
Transition: Any State to Error
Required Attributes: None
Optional Attributes: None allowed
Actions: Queue processing is stopped. Work Requests pending or in
process are completed in error, when possible.
This patch allows the transition and quiets the message.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Improve safety of code by checking the size of the data buffer and
prevent buffer overrun
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Neel Desai <neel.desai@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In process_receive_packet the packet header field is used to calculate
the length of the packet. However this is not necessarily setup. In fact
only if the ECN prescan is enabled will the packet header be valid at
this point.
The code works as is because we do not do anything with the packet
length at this point in the packet processing. The length and header are
setup correctly in hfi1_setup_ib_header which is called by the following
sequence:
process_receive_packet()
-> rhf_receieve_function_map[]()
--> process_receive_ib()
---> hfi1_setup_9B_packet()
----> hfi1_setup_ib_header()
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ensure we can't come up with an array size that is bigger than the array
by applying the QPN mask before the divide in the free_qpn function.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Spell receive correctly in OPA_LINKDOWN_REASON_RCV_ERROR
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
As the code stands today the array access in remap_intr() is OK. To
future proof the code though we should explicitly check to ensure the
index value is not outside of the valid range. This is not a straight
forward calculation so err on the side of caution.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The free_qpn() function from the hfi1/qib driver which was the basis for
rdmavt_free_qpn() function was accidentally left in the code. Remove it.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
sdma_init does not take a number of sdma engine parameters,
rather it initializes all of the sdma engines.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Reclassify messages printed out to /var/log/messages into
warnings and errors to facilitate debugging in the future
for issues related to the platform config logic.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Atomic bit tests are used to single errors and the
completion of request submissions. These operations
don't need to be atomic and show to be expensive on
the profile.
Replace each atomic bit operation with a bool type
and a READ_ONCE/WRITE_ONCE pairing.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The atomic SDMA_REQ_SEND_DONE bit is set by the
process-level code, and then the same process-level
code uses the bit to test that all packets have been
submitted incurring a costly atomic read.
Use a bool type with a READ_ONCE/WRITE_ONCE
pairing for this bit, and use the same condition that
is used to set the bit to test that all packets have
been submitted.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Provide the ability for IB clients to modify the OPA specific
capability mask and include this mask in the subsequent trap data.
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Michael N. Henry <michael.n.henry@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
pci_enable_msix_range() and pci_disable_msix() have been deprecated.
Updating to the new pci_alloc_irq_vectors() interface.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To improve the readability of function prototypes, give the parameters
names in the affinity module.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The current user SDMA request structure layout has holes.
The cachelines can be reduced to improve cacheline trading.
Separate fields in the following categories: mostly read,
writable and shared with interrupt.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
An RB tree is used for the SDMA pinning cache. Cache
entries are extracted and reinserted from the tree
in case the address range for it changes. However,
if the address range for the entry doesn't change,
deleting the entry from the RB tree is not necessary.
This affects performance since the tree needs to be
rebalanced for each insertion, and this happens in
the hot path. Optimize RB search by not removing
entries when it's not needed.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
SGEs that are contiguous needlessly consume driver dependent TX resources.
The lkey validation logic is enhanced to compress the SGE that ends
up in the send wqe when consecutive addresses are detected.
The lkey validation API used to return 1 (success) or 0 (fail).
The return value is now an -errno, 0 (compressed), or 1 (uncompressed). A
additional argument is added to pass the last SQE for the compression.
Loopback callers always pass a NULL to last_sge since the optimization is
of little benefit in that situation.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We move many common IB fields into the hfi1_packet structure and
set them up in a single function. This allows us to set the fields
in a single place and not deal with them throughout the driver.
Reviewed-by: Brian Welty <brian.welty@intel.com>
Reviewed-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Calls to trace incoming packets will now receive the packet
context as parameter. This enables trace support for future
packet types.
Header trace output is in the format <field>:<value>
which makes parsing easier.
input_ibhdr trace before change:
<idle>-0 [001] d.h. 5904.250925: input_ibhdr: [0000:05:00.0] vl 0
lver 0 sl 0 lnh 2,LRH_BTH dlid 0002 len 18 slid 0001 op
0x64,UD_SEND_ONLY se 0 m 0 pad 0 tver 0 pkey 0xffff f 0 b 0 qpn 0x000001
a 0 psn 0x000001b2 deth qkey 0x80010000 sqpn 0x000001
input_ibhdr trace after change:
<idle>-0 [001] d.h. 6655.714488: input_ibhdr: [0000:05:00.0] (IB)
len:124 sc:0 dlid:0x0001 slid:0x0002 lnh:2,LRH_BTH lver:0 sl:0 age:0
becn:0 fecn:0 l4:0 rc:0 entropy:0 op:0x64,UD_SEND_ONLY se:0 m:0 pad:0
tver:0 pkey:0x7fff f:0 b:0 qpn:0x000001 a:0 psn:0x00000036 hlen:8 deth
qkey:0x80010000 sqpn:0x000001
Reviewed-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Improve code readablity by adding inline functions
to read specific BTH/IB fields without knowledge of
byte offsets.
Reviewed-by: Brian Welty <brian.welty@intel.com>
Reviewed-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Leftover function that is not used. Remove it.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The tx request is unnecessarily initialized in the hot
code path with memset(), however, there's no need to do
this as most fields are initialized later on. this
initialization shows to be costly in the profile.
Remove unnecessary initialization from tx request and make
sure all variables are initialized properly.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Reserved gids are taken by the mlx5_core, report smaller GID table
size to IB core.
Set mlx5_query_roce_port's return value back to int. In case of
error, return an indication. This rolls back some of the change
in commit 50f22fd8ec ("IB/mlx5: Set mlx5_query_roce_port's return value to void")
Change set_roce_addr to use gid_set function, instead of directly
sending the command.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the qed_roce_if file to qed_rdma_if as it
represents a common interface for RoCE and iWARP.
this commit affects RDMA/qedr as well.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the functions common to both iWARP and RoCE to have a prefix of
_rdma_ instead of _roce_.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once we have iWARP support, the qede portion of the qedr<->qede would
serve all the RDMA protocols - so rename the file to be appropriate
to its function.
While we're at it, we're also moving a couple of inclusions to it into
.h files and adding includes to make sure it contains all type
definitions it requires.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP would require the chains to allocate/free their PBL memory
independently, so add the infrastructure to provide it externally.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename:
wait_queue_t => wait_queue_entry_t
'wait_queue_t' was always a slight misnomer: its name implies that it's a "queue",
but in reality it's a queue *entry*. The 'real' queue is the wait queue head,
which had to carry the name.
Start sorting this out by renaming it to 'wait_queue_entry_t'.
This also allows the real structure name 'struct __wait_queue' to
lose its double underscore and become 'struct wait_queue_entry',
which is the more canonical nomenclature for such data types.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This series provide some updates and cleanups for mlx5 core and netdevice
driver.
From Eli Cohen, add a missing event string.
From Or Gerlitz, some checkpatch cleanups.
From Moni, Disalbe HW level LAG when SRIOV is enabled.
From Tariq, A code reuse cleanup in aRFS flow.
From Itay Aveksis, Typo fix.
From Gal Pressman, ethtool statistics updates and "update stats" deferred work optimizations.
From Majd Dibbiny, Fast unload support on kernel shutdown.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZQv0+AAoJEEg/ir3gV/o+1iQH/15I5Pr9KoCWSTN9aUglRupU
8HmJhkf7Novaro6WtIybgMGkdoNTrmHgyTEngAkRq5a5Ws/LrC/1wLH+lVMDh+Fx
/2a5cfPsK483gHWBtAbasBD8SHnsyTIeVnEhuDsevHQNkz3HGuKOgx5ZHF1sdkHU
bj/QU06LNPKAlMDI/wKod13MB4+AdTFemaJRCCgXFvu/p/EfVvB+TStdOsrxj1kx
lDIwkCykJSJsg38HoLXt7Z12nWwgHGf2De04RukKeJ6C6KTdKcUu5EYbaL9BSZZT
jiIayYjRgeXzNhY4R5yLPc0FkecNIgC90YJShUN3nR3PWa+ytaHpfJQPOS4/AW8=
=Tjmk
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-06-16' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox mlx5 updates and cleanups 2017-06-16
mlx5-updates-2017-06-16
This series provide some updates and cleanups for mlx5 core and netdevice
driver.
From Eli Cohen, add a missing event string.
From Or Gerlitz, some checkpatch cleanups.
From Moni, Disalbe HW level LAG when SRIOV is enabled.
From Tariq, A code reuse cleanup in aRFS flow.
From Itay Aveksis, Typo fix.
From Gal Pressman, ethtool statistics updates and "update stats" deferred work optimizations.
From Majd Dibbiny, Fast unload support on kernel shutdown.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- A fix for fix eea40b8f62 ("infiniband: call ipv6 route lookup via the
stub interface")
- 6 patches against bnxt_re...the first two are considerably larger than
I would like, but as they address real issues I went ahead and
submitted them (it also helped that a good deal of the churn was
removing code repeated in multiple places and consolidating it to one
common function)
- 2 fixes against qedr that just came in
- 1 fix against rxe that took a few revisions to get right plus time to
get the proper reviews
- 5 late breaking IPoIB fixes
- 1 late cxgb4 fix
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZQY2UAAoJELgmozMOVy/d/goP/1uNXbrSG7CfdOykvGdm4lbN
rmal4D0ChqivDsEll+eEaCBPBFZnQXbK/n5Fu/R4+qvFCWPqxAV0kMckKYsEMYNK
Q9zh6h3jxeBA8ms5D6MeZt31tzMG4VQjjs0LvbIz1S0wHbHuNd2dPCMwxKNOmm0H
eTJQ7SAssYnHJmWnQI0R6QZPfAcOOT2HgLsBdvq8apIk7tRRzflQ5YQWZE1X4cv0
iYshMgmkSR9vgr83YZwYQYd6Uc/yUDj87FrBR7ELUyE9Dr0tMoprtM3fekw78uLE
YBiIMb6NwUH+2q5bxPuaq0DulEsdEdMPdtNOY/VRSduqCkdlGPS0KMvLzHcm701b
Ks6gQQMvpb5lNUPasmGkowz7gwTrIniKu9nZUcJ/4BZRH4ax6hrZh3yj/Kx4GuxF
hp+KZPokytLfNEhuJKgrIQx6r2kfMJKr6eTDEAVp8dZ54bymWQgZhoQ8lLFF2isQ
MuCM2p7G/gauu5WrMZBc4vjvWaHAfV60KrCwxJQwQIBZwTRwA619nuDi3McED1R8
YS3pUxu3QJRaZWqI4vS10CUTxAz/4NVHLjE2rkDJAMMKRfBu94CTU/DklQ6jejKr
njvK5uryjTaJWN8F/EKRs85NhA/yqZpb8rDhoWn3ri7eyHdj9SsEw0RpVIorYiqT
zsk6SIT9biA5bs46kQ6P
=blNV
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"I had thought at the time of the last pull request that there wouldn't
be much more to go, but several things just kept trickling in over the
last week.
Instead of just the six patches to bnxt_re that I had anticipated,
there are another five IPoIB patches, two qedr patches, and a few
other miscellaneous patches.
The bnxt_re patches are more lines of diff than I like to submit this
late in the game. That's mostly because of the first two patches in
the series of six. I almost dropped them just because of the lines of
churn, but on a close review, a lot of the churn came from removing
duplicated code sections and consolidating them into callable
routines. I felt like this made the number of lines of change more
acceptable, and they address problems, so I left them. The remainder
of the patches are all small, well contained, and well understood.
These have passed 0day testing, but have not been submitted to
linux-next (but a local merge test with your current master was
without any conflicts).
Summary:
- A fix for fix eea40b8f62 ("infiniband: call ipv6 route lookup via
the stub interface")
- Six patches against bnxt_re...the first two are considerably larger
than I would like, but as they address real issues I went ahead and
submitted them (it also helped that a good deal of the churn was
removing code repeated in multiple places and consolidating it to
one common function)
- Two fixes against qedr that just came in
- One fix against rxe that took a few revisions to get right plus
time to get the proper reviews
- Five late breaking IPoIB fixes
- One late cxgb4 fix"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
rdma/cxgb4: Fix memory leaks during module exit
IB/ipoib: Fix memory leak in create child syscall
IB/ipoib: Fix access to un-initialized napi struct
IB/ipoib: Delete napi in device uninit default
IB/ipoib: Limit call to free rdma_netdev for capable devices
IB/ipoib: Fix memory leaks for child interfaces priv
rxe: Fix a sleep-in-atomic bug in post_one_send
RDMA/qedr: Add 64KB PAGE_SIZE support to user-space queues
RDMA/qedr: Initialize byte_len in WC of READ and SEND commands
RDMA/bnxt_re: Remove FMR support
RDMA/bnxt_re: Fix RQE posting logic
RDMA/bnxt_re: Add HW workaround for avoiding stall for UD QPs
RDMA/bnxt_re: Dereg MR in FW before freeing the fast_reg_page_list
RDMA/bnxt_re: HW workarounds for handling specific conditions
RDMA/bnxt_re: Fixing the Control path command and response handling
IB/addr: Fix setting source address in addr6_resolve()
Fixed few places where endianness was misspelled and
one spot whwere output was:
CHECK: 'endianess' may be misspelled - perhaps 'endianness'?
CHECK: 'ouput' may be misspelled - perhaps 'output'?
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull crypto fix from Herbert Xu:
"This fixes a bug on sparc where we may dereference freed stack memory"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: Work around deallocated stack frame reference gcc bug on sparc.
The flow of creating a new child goes through ipoib_vlan_add
which allocates a new interface and checks the rtnl_lock.
If the lock is taken, restart_syscall will be called to restart
the system call again. In this case we are not releasing the
already allocated interface, causing a leak.
Fixes: 9baa0b0364 ("IB/ipoib: Add rtnl_link_ops support")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch mekas init_default and uninit_default symmetric
with a call to delete napi. Additionally, the uninit_default
gained delete napi call in case of init_default fails.
Fixes: 515ed4f3aa ('IB/IPoIB: Separate control and data related initializations')
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is a need to free priv explicitly and not just to release
the device, child priv is freed explicitly on remove flow and this
patch also includes priv free on error flow in P_key creation
and also in add_port.
Fixes: cd565b4b51 ('IB/IPoIB: Support acceleration options callbacks')
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The driver may sleep under a spin lock, and the function call path is:
post_one_send (acquire the lock by spin_lock_irqsave)
init_send_wqe
copy_from_user --> may sleep
There is no flow that makes "qp->is_user" true, and copy_from_user may
cause bug when a non-user pointer is used. So the lines of copy_from_user
and check of "qp->is_user" are removed.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add 64KB PAGE_SIZE support to user-space CQ, SQ and RQ queues.
De-facto it means that code was added to translate 64KB
pages to smaller 4KB pages that the FW can handle. Otherwise,
the FW would wrap (or jump to the next page) when reaching 4KB
while the user space library will continue on the same large page.
Note that MR code remains as is since the FW supports larger pages
for MRs.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Initialize byte_len in work completion of RDMA_READ and RDMA_SEND.
Exposed by uDAPL application.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some issues observed with FMR implementation
while running stress traffic. So removing the
FMR verbs support for now.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds code to ring RQ Doorbell aggressively
so that the adapter can DMA RQ buffers sooner, instead
of DMA all WQEs in the post_recv WR list together at the
end of the post_recv verb.
Also use spinlock to serialize RQ posting
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
HW stalls out after 0x800000 WQEs are posted for UD QPs.
To workaround this problem, driver will send a modify_qp cmd
to the HW at around the halfway mark(0x400000) so that FW
can accordingly modify the QP context in the HW to prevent this
stall.
This workaround needs to be done for UD, QP1 and Raw Ethertype
packets. Added a counter to keep track of WQEs posted during post_send.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the host buffers are freed before destroying MR in HW,
HW could try accessing these buffers. This could cause a host
crash. Fixing the code to avoid this condition.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch implements the following HW workarounds
1. The SQ depth needs to be augmented by 128 + 1 to avoid running
into an Out of order CQE issue
2. Workaround to handle the problem where the HW fast path engine continues
to access DMA memory in retranmission mode even after the WQE has
already been completed. If the HW reports this condition, driver detects
it and posts a Fence WQE. The driver stops reporting the completions
to stack until it receives completion for Fence WQE.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fixing a concurrency issue with creq handling. Each caller
was given a globally managed crsq element, which was
accessed outside a lock. This could result in corruption,
if lot of applications are simultaneously issuing Control Path
commands. Now, each caller will provide its own response buffer
and the responses will be copied under a lock.
Also, Fixing the queue full condition check for the CMDQ.
As a part of these changes, the control path code is refactored
to remove the code replication in the response status checking.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We are trying to get rid of DRIVER_ATTR(), and all of the nes.c driver
attributes can be trivially changed to use DRIVER_ATTR_RW(), making the
code smaller and easier to manage over time.
Cc: Faisal Latif <faisal.latif@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: <linux-rdma@vger.kernel.org>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LL2 today is interrupt driven - when tx/rx completion arrives [or any
other indication], qed needs to operate on the connection and pass
the information to the protocol-driver [or internal qed consumer].
Since we have several flavors of ll2 employeed by the driver,
each handler needs to do an if-else to determine the right functionality
to use based on the connection type.
In order to make things more scalable [given that we're going to add
additional types of ll2 flavors] move the infrastrucutre into using
a callback-based approach - the callbacks would be provided as part
of the connection's initialization parameters.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to move some TCP sysctls to net namespaces in the future.
tcp_window_scaling, tcp_sack and tcp_timestamps being fetched
from tcp_parse_options(), we need to pass an extra parameter.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On sparc, if we have an alloca() like situation, as is the case with
SHASH_DESC_ON_STACK(), we can end up referencing deallocated stack
memory. The result can be that the value is clobbered if a trap
or interrupt arrives at just the right instruction.
It only occurs if the function ends returning a value from that
alloca() area and that value can be placed into the return value
register using a single instruction.
For example, in lib/libcrc32c.c:crc32c() we end up with a return
sequence like:
return %i7+8
lduw [%o5+16], %o0 ! MEM[(u32 *)__shash_desc.1_10 + 16B],
%o5 holds the base of the on-stack area allocated for the shash
descriptor. But the return released the stack frame and the
register window.
So if an intererupt arrives between 'return' and 'lduw', then
the value read at %o5+16 can be corrupted.
Add a data compiler barrier to work around this problem. This is
exactly what the gcc fix will end up doing as well, and it absolutely
should not change the code generated for other cpus (unless gcc
on them has the same bug :-)
With crucial insight from Eric Sandeen.
Cc: <stable@vger.kernel.org>
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove date and bump version for mlx4_ib driver.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the adapter consumes two tids for every ipv6 offload
connection be it active or passive, calculate tid usage
count accordingly.
Also change the signatures of relevant functions to get
the address family.
Signed-off-by: Rizwan Ansari <rizwana@chelsio.com>
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit eea40b8f62 ("infiniband: call ipv6 route lookup via the stub
interface") introduced a regression in address resolution when connecting
to IPv6 destination addresses. The old code called ip6_route_output(),
while the new code calls ipv6_stub->ipv6_dst_lookup(). The two are almost
the same, except that ipv6_dst_lookup() also calls ip6_route_get_saddr()
if the source address is in6addr_any.
This means that the test of ipv6_addr_any(&fl6.saddr) now never succeeds,
and so we never copy the source address out. This ends up causing
rdma_resolve_addr() to fail, because without a resolved source address,
cma_acquire_dev() will fail to find an RDMA device to use. For me, this
causes connecting to an NVMe over Fabrics target via RoCE / IPv6 to fail.
Fix this by copying out fl6.saddr if ipv6_addr_any() is true for the original
source address passed into addr6_resolve(). We can drop our call to
ipv6_dev_get_saddr() because ipv6_dst_lookup() already does that work.
Fixes: eea40b8f62 ("infiniband: call ipv6 route lookup via the stub interface")
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Roland Dreier <roland@purestorage.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Commit 9fdca4da4d (IB/SA: Split struct sa_path_rec based on IB and
ROCE specific fields) moved the service_id to be specific attribute
for IB and OPA SA Path Record, and thus wasn't assigned for RoCE.
This caused to the following kernel panic in the CMA request handler flow:
[ 27.074594] BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
[ 27.074731] IP: __radix_tree_lookup+0x1d/0xe0
...
[ 27.075356] Workqueue: ib_cm cm_work_handler [ib_cm]
[ 27.075401] task: ffff88022e3b8000 task.stack: ffffc90001298000
[ 27.075449] RIP: 0010:__radix_tree_lookup+0x1d/0xe0
...
[ 27.075979] Call Trace:
[ 27.076015] radix_tree_lookup+0xd/0x10
[ 27.076055] cma_ps_find+0x59/0x70 [rdma_cm]
[ 27.076097] cma_id_from_event+0xd2/0x470 [rdma_cm]
[ 27.076144] ? ib_init_ah_from_path+0x39a/0x590 [ib_core]
[ 27.076193] cma_req_handler+0x25/0x480 [rdma_cm]
[ 27.076237] cm_process_work+0x25/0x120 [ib_cm]
[ 27.076280] ? cm_get_bth_pkey.isra.62+0x3c/0xa0 [ib_cm]
[ 27.076350] cm_req_handler+0xb03/0xd40 [ib_cm]
[ 27.076430] ? sched_clock_cpu+0x11/0xb0
[ 27.076478] cm_work_handler+0x194/0x1588 [ib_cm]
[ 27.076525] process_one_work+0x160/0x410
[ 27.076565] worker_thread+0x137/0x4a0
[ 27.076614] kthread+0x112/0x150
[ 27.076684] ? max_active_store+0x60/0x60
[ 27.077642] ? kthread_park+0x90/0x90
[ 27.078530] ret_from_fork+0x2c/0x40
This patch moves it back to the common SA Path Record structure
and removes the redundant setter and getter.
Tested on Connect-IB and Connect-X4 in Infiniband and RoCE respectively.
Fixes: 9fdca4da4d (IB/SA: Split struct sa_path_rec based on IB ands
ROCE specific fields)
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This change will optimize kernel memory deregistration operations.
__ib_umem_release() used to call set_page_dirty_lock() against every
writable page in its memory region. Its purpose is to keep data
synced between CPU and DMA device when swapping happens after mem
deregistration ops. Now we choose not to set page dirty bit if it's
already set by kernel prior to calling __ib_umem_release(). This
reduces memory deregistration time by half or even more when we ran
application simulation test program.
Signed-off-by: Qing Huang <qing.huang@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Commit 5752075144 ("IB/SA: Add OPA path record type") introduced
new local function __ib_copy_path_rec_to_user, but didn't limit its
scope. This produces the following sparse warning:
drivers/infiniband/core/uverbs_marshall.c:99:6: warning:
symbol '__ib_copy_path_rec_to_user' was not declared. Should it be
static?
In addition, it used sizeof ... notations instead of sizeof(...), which
is correct in C, but a little bit misleading. Let's change it too.
Fixes: 5752075144 ("IB/SA: Add OPA path record type")
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RDMA netlink is part of ib_core, hence ibnl_chk_listeners(),
ibnl_init() and ibnl_cleanup() don't need to be published
in public header file.
Let's remove EXPORT_SYMBOL from ibnl_chk_listeners() and move all these
functions to private header file.
CC: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If srp_init_qp() fails at srp_create_ch_ib() then ch->send_cq
may be NULL.
Calling directly to ib_destroy_qp() is sufficient because
no work requests were posted on the created qp.
Fixes: 9294000d6d ("IB/srp: Drain the send queue before destroying a QP")
Cc: <stable@vger.kernel.org>
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Bart van Assche <bart.vanassche@sandisk.com>--
Signed-off-by: Doug Ledford <dledford@redhat.com>
ipoib_dev_uninit_default() call is used in ipoib_main.c file only
and it generates the following warning from smatch tool:
drivers/infiniband/ulp/ipoib/ipoib_main.c:1593:6: warning:
symbol 'ipoib_dev_uninit_default' was not declared. Should it
be static?
so let's declare that function as static.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Cache the needed umr_fence and set the wqe ctrl segmennt
accordingly.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The cited patch added a type field to structures ib_ah and rdma_ah_attr.
Function mlx4_ib_query_ah() builds an rdma_ah_attr structure from the
data in an mlx4_ib_ah structure (which contains both an ib_ah structure
and an address vector).
For mlx4_ib_query_ah() to work properly, the type field in the contained
ib_ah structure must be set correctly.
In the outgoing MAD tunneling flow, procedure mlx4_ib_multiplex_mad()
paravirtualizes a MAD received from a slave and sends the processed
mad out over the wire. During this processing, it populates an
mlx4_ib_ah structure and calls mlx4_ib_query_ah().
The cited commit overlooked setting the type field in the contained
ib_ah structure before invoking mlx4_ib_query_ah(). As a result, the
type field remained uninitialized, and the rdma_ah_attr structure was
incorrectly built. This resulted in improperly built MADs being sent out
over the wire.
This patch properly initializes the type field in the contained ib_ah
structure before calling mlx4_ib_query_ah(). The rdma_ah_attr structure
is then generated correctly.
Fixes: 44c58487d5 ("IB/core: Define 'ib' and 'roce' rdma_ah_attr types")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The handling of IB_RDMA_WRITE_ONLY_WITH_IMMEDIATE will leak a memory
reference when a buffer cannot be allocated for returning the immediate
data.
The issue is that the rkey validation has already occurred and the RNR
nak fails to release the reference that was fruitlessly gotten. The
the peer will send the identical single packet request when its RNR
timer pops.
The fix is to release the held reference prior to the rnr nak exit.
This is the only sequence the requires both rkey validation and the
buffer allocation on the same packet.
Cc: Stable <stable@vger.kernel.org> # 4.7+
Tested-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Keep VL15 credits at 0 during LNI, before link-up. Store
VL15 credits value during verify cap interrupt and set
in after link-up. This addresses an issue where VL15 MAD
packets could be sent by one side of the link before
the other side is ready to receive them.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The Omni-Path adapter driver fails to load on the ppc64le platform
due to invalid PCI setup.
This patch makes the PCI configuration more robust and will
fix 64 bit addressing for ppc64le.
Signed-off-by: Steven L Roberts <robers97@gmail.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This fixes a kernel panic when loading the hfi driver as a dynamic module.
Signed-off-by: Steven L Roberts <robers97@gmail.com>
Reviewed-by: Leon Romanovsky <leon@kernel.org>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Take care of ipv6 checks while computing header length for deducing mtu
size of ipv6 servers. Due to the incorrect header length computation for
ipv6 servers, wrong mss is reported to the peer (client).
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The patch 761e19a504 (RDMA/iw_cxgb4: Handle return value of
c4iw_ofld_send() in abort_arp_failure()) from May 6, 2016
leads to the following static checker warning:
drivers/infiniband/hw/cxgb4/cm.c:575 abort_arp_failure()
warn: passing freed memory 'skb'
Also fixes skb leak when l2t resolution fails
Fixes: 761e19a504 (RDMA/iw_cxgb4: Handle return value of
c4iw_ofld_send() in abort_arp_failure())
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Explicitly ACK the MPA Reply frame so the peer
does not retransmit the frame.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Don't set control flag for 0-length FULPDU (Send) RTR indication
in the enhanced MPA Request/Reply frames, because it isn't supported.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some error paths in i40iw_initialize_dev are doing
additional and unnecessary work before exiting.
Correctly free resources allocated prior to error
and return with correct status code.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intelcom>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Explicitly ACK the MPA Reject frame so the peer does
not retransmit the frame.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Don't set control flag for 0-length FULPDU (Send)
RTR indication in the enhanced MPA Request/Reply
frames, because it isn't supported.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Allocate and free a security context when creating and destroying a MAD
agent. This context is used for controlling access to PKeys and sending
and receiving SMPs.
When sending or receiving a MAD check that the agent has permission to
access the PKey for the Subnet Prefix of the port.
During MAD and snoop agent registration for SMI QPs check that the
calling process has permission to access the manage the subnet and
register a callback with the LSM to be notified of policy changes. When
notificaiton of a policy change occurs recheck permission and set a flag
indicating sending and receiving SMPs is allowed.
When sending and receiving MADs check that the agent has access to the
SMI if it's on an SMI QP. Because security policy can change it's
possible permission was allowed when creating the agent, but no longer
is.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Acked-by: Doug Ledford <dledford@redhat.com>
[PM: remove the LSM hook init code]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Add a generic notificaiton mechanism in the LSM. Interested consumers
can register a callback with the LSM and security modules can produce
events.
Because access to Infiniband QPs are enforced in the setup phase of a
connection security should be enforced again if the policy changes.
Register infiniband devices for policy change notification and check all
QPs on that device when the notification is received.
Add a call to the notification mechanism from SELinux when the AVC
cache changes or setenforce is cleared.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Acked-by: James Morris <james.l.morris@oracle.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Add new LSM hooks to allocate and free security contexts and check for
permission to access a PKey.
Allocate and free a security context when creating and destroying a QP.
This context is used for controlling access to PKeys.
When a request is made to modify a QP that changes the port, PKey index,
or alternate path, check that the QP has permission for the PKey in the
PKey table index on the subnet prefix of the port. If the QP is shared
make sure all handles to the QP also have access.
Store which port and PKey index a QP is using. After the reset to init
transition the user can modify the port, PKey index and alternate path
independently. So port and PKey settings changes can be a merge of the
previous settings and the new ones.
In order to maintain access control if there are PKey table or subnet
prefix change keep a list of all QPs are using each PKey index on
each port. If a change occurs all QPs using that device and port must
have access enforced for the new cache settings.
These changes add a transaction to the QP modify process. Association
with the old port and PKey index must be maintained if the modify fails,
and must be removed if it succeeds. Association with the new port and
PKey index must be established prior to the modify and removed if the
modify fails.
1. When a QP is modified to a particular Port, PKey index or alternate
path insert that QP into the appropriate lists.
2. Check permission to access the new settings.
3. If step 2 grants access attempt to modify the QP.
4a. If steps 2 and 3 succeed remove any prior associations.
4b. If ether fails remove the new setting associations.
If a PKey table or subnet prefix changes walk the list of QPs and
check that they have permission. If not send the QP to the error state
and raise a fatal error event. If it's a shared QP make sure all the
QPs that share the real_qp have permission as well. If the QP that
owns a security structure is denied access the security structure is
marked as such and the QP is added to an error_list. Once the moving
the QP to error is complete the security structure mark is cleared.
Maintaining the lists correctly turns QP destroy into a transaction.
The hardware driver for the device frees the ib_qp structure, so while
the destroy is in progress the ib_qp pointer in the ib_qp_security
struct is undefined. When the destroy process begins the ib_qp_security
structure is marked as destroying. This prevents any action from being
taken on the QP pointer. After the QP is destroyed successfully it
could still listed on an error_list wait for it to be processed by that
flow before cleaning up the structure.
If the destroy fails the QPs port and PKey settings are reinserted into
the appropriate lists, the destroying flag is cleared, and access control
is enforced, in case there were any cache changes during the destroy
flow.
To keep the security changes isolated a new file is used to hold security
related functionality.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Acked-by: Doug Ledford <dledford@redhat.com>
[PM: merge fixup in ib_verbs.h and uverbs_cmd.c]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Cache the subnet prefix and add a function to access it. Enforcing
security requires frequent queries of the subnet prefix and the pkeys in
the pkey table.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Commit a7c3e901a4 ("mm: introduce kv[mz]alloc helpers") added
proper implementation of mlx5_vzalloc function to the MM core.
This made the mlx5_vzalloc function useless, so let's remove it.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull SCSI target updates from Nicholas Bellinger:
"Things were a lot more calm than previously expected. It's primarily
fixes in various areas, with most of the new functionality centering
around TCMU backend driver work that Xiubo Li has been driving.
Here's the summary on the feature side:
- Make T10-PI verify configurable for emulated (FILEIO + RD) backends
(Dmitry Monakhov)
- Allow target-core/TCMU pass-through to use in-kernel SPC-PR logic
(Bryant Ly + MNC)
- Add TCMU support for growing ring buffer size (Xiubo Li + MNC)
- Add TCMU support for global block data pool (Xiubo Li + MNC)
and on the bug-fix side:
- Fix COMPARE_AND_WRITE non GOOD status handling for READ phase
failures (Gary Guo + nab)
- Fix iscsi-target hang with explicitly changing per NodeACL
CmdSN number depth with concurrent login driven session
reinstatement. (Gary Guo + nab)
- Fix ibmvscsis fabric driver ABORT task handling (Bryant Ly)
- Fix target-core/FILEIO zero length handling (Bart Van Assche)
Also, there was an OOPs introduced with the WRITE_VERIFY changes that
I ended up reverting at the last minute, because as not unusual Bart
and I could not agree on the fix in time for -rc1. Since it's specific
to a conformance test, it's been reverted for now.
There is a separate patch in the queue to address the underlying
control CDB write overflow regression in >= v4.3 separate from the
WRITE_VERIFY revert here, that will be pushed post -rc1"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (30 commits)
Revert "target: Fix VERIFY and WRITE VERIFY command parsing"
IB/srpt: Avoid that aborting a command triggers a kernel warning
IB/srpt: Fix abort handling
target/fileio: Fix zero-length READ and WRITE handling
ibmvscsis: Do not send aborted task response
tcmu: fix module removal due to stuck thread
target: Don't force session reset if queue_depth does not change
iscsi-target: Set session_fall_back_to_erl0 when forcing reinstatement
target: Fix compare_and_write_callback handling for non GOOD status
tcmu: Recalculate the tcmu_cmd size to save cmd area memories
tcmu: Add global data block pool support
tcmu: Add dynamic growing data area feature support
target: fixup error message in target_tg_pt_gp_tg_pt_gp_id_store()
target: fixup error message in target_tg_pt_gp_alua_access_type_store()
target/user: PGR Support
target: Add WRITE_VERIFY_16
Documentation/target: add an example script to configure an iSCSI target
target: Use kmalloc_array() in transport_kmap_data_sg()
target: Use kmalloc_array() in compare_and_write_callback()
target: Improve size determinations in two functions
...
This includes:
* Some code optimizations for the Intel VT-d driver
* Code to switch off a previously enabled Intel IOMMU
* Support for 'struct iommu_device' for OMAP, Rockchip and
Mediatek IOMMUs
* Some header optimizations for IOMMU core code headers and a
few fixes that became necessary in other parts of the kernel
because of that
* ACPI/IORT updates and fixes
* Some Exynos IOMMU optimizations
* Code updates for the IOMMU dma-api code to bring it closer to
use per-cpu iova caches
* New command-line option to set default domain type allocated
by the iommu core code
* Another command line option to allow the Intel IOMMU switched
off in a tboot environment
* ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using
an IDENTITY domain in conjunction with DMA ops, Support for
SMR masking, Support for 16-bit ASIDs (was previously broken)
* Various other small fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3aE8
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- code optimizations for the Intel VT-d driver
- ability to switch off a previously enabled Intel IOMMU
- support for 'struct iommu_device' for OMAP, Rockchip and Mediatek
IOMMUs
- header optimizations for IOMMU core code headers and a few fixes that
became necessary in other parts of the kernel because of that
- ACPI/IORT updates and fixes
- Exynos IOMMU optimizations
- updates for the IOMMU dma-api code to bring it closer to use per-cpu
iova caches
- new command-line option to set default domain type allocated by the
iommu core code
- another command line option to allow the Intel IOMMU switched off in
a tboot environment
- ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using an
IDENTITY domain in conjunction with DMA ops, Support for SMR masking,
Support for 16-bit ASIDs (was previously broken)
- various other small fixes and improvements
* tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (63 commits)
soc/qbman: Move dma-mapping.h include to qman_priv.h
soc/qbman: Fix implicit header dependency now causing build fails
iommu: Remove trace-events include from iommu.h
iommu: Remove pci.h include from trace/events/iommu.h
arm: dma-mapping: Don't override dma_ops in arch_setup_dma_ops()
ACPI/IORT: Fix CONFIG_IOMMU_API dependency
iommu/vt-d: Don't print the failure message when booting non-kdump kernel
iommu: Move report_iommu_fault() to iommu.c
iommu: Include device.h in iommu.h
x86, iommu/vt-d: Add an option to disable Intel IOMMU force on
iommu/arm-smmu: Return IOVA in iova_to_phys when SMMU is bypassed
iommu/arm-smmu: Correct sid to mask
iommu/amd: Fix incorrect error handling in amd_iommu_bind_pasid()
iommu: Make iommu_bus_notifier return NOTIFY_DONE rather than error code
omap3isp: Remove iommu_group related code
iommu/omap: Add iommu-group support
iommu/omap: Make use of 'struct iommu_device'
iommu/omap: Store iommu_dev pointer in arch_data
iommu/omap: Move data structures to omap-iommu.h
iommu/omap: Drop legacy-style device support
...
Pull misc vfs updates from Al Viro:
"Assorted bits and pieces from various people. No common topic in this
pile, sorry"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs/affs: add rename exchange
fs/affs: add rename2 to prepare multiple methods
Make stat/lstat/fstatat pass AT_NO_AUTOMOUNT to vfs_statx()
fs: don't set *REFERENCED on single use objects
fs: compat: Remove warning from COMPATIBLE_IOCTL
remove pointless extern of atime_need_update_rcu()
fs: completely ignore unknown open flags
fs: add a VALID_OPEN_FLAGS
fs: remove _submit_bh()
fs: constify tree_descr arrays passed to simple_fill_super()
fs: drop duplicate header percpu-rwsem.h
fs/affs: bugfix: Write files greater than page size on OFS
fs/affs: bugfix: enable writes on OFS disks
fs/affs: remove node generation check
fs/affs: import amigaffs.h
fs/affs: bugfix: make symbolic links work again
- mlx5/IPoIB fixup patch
-----BEGIN PGP SIGNATURE-----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=Ihe9
-----END PGP SIGNATURE-----
mergetag object 67cf3623e0
type commit
tag for-next
tagger Doug Ledford <dledford@redhat.com> 1493940800 -0400
Updates #3 for 4.12 kernel merge window
- The hfi1 15 patch set that landed late
- IPoIB get_link_ksettings which landed late because I asked for a
respin
- One late rxe change
- One -rc worthy fix that's in early
-----BEGIN PGP SIGNATURE-----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=H9f5
-----END PGP SIGNATURE-----
Merge tags 'for-linus' and 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma updates from Doug Ledford:
"As mentioned in my first pull request, this is the subsequent pull
requests I had. This is all I have, and in fact this cleans out the
RDMA subsystem's entire patchworks queue of kernel changes that are
ready to go (well, it did for the weekend anyway, a few new patches
are in, but they'll be coming during the -rc cycle).
The first tag contains a single patch that would have conflicted if
taken from my tree or DaveM's tree as it needed our trees merged to
come cleanly.
The second tag contains the patch series from Intel plus three other
stragllers that came in late last week. I took them because it allowed
me to legitimately claim that the RDMA patchworks queue was, for a
short time, 100% cleared of all waiting kernel patches, woohoo! :-).
I have it under my for-next tag, so it did get 0day and linux- next
over the end of last week, and linux-next did show one minor conflict.
Summary:
'for-linus' tag:
- mlx5/IPoIB fixup patch
'for-next' tag:
- the hfi1 15 patch set that landed late
- IPoIB get_link_ksettings which landed late because I asked for a
respin
- one late rxe change
- one -rc worthy fix that's in early"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/mlx5: Enable IPoIB acceleration
* tag 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
rxe: expose num_possible_cpus() cnum_comp_vectors
IB/rxe: Update caller's CRC for RXE_MEM_TYPE_DMA memory type
IB/hfi1: Clean up on context initialization failure
IB/hfi1: Fix an assign/ordering issue with shared context IDs
IB/hfi1: Clean up context initialization
IB/hfi1: Correctly clear the pkey
IB/hfi1: Search shared contexts on the opened device, not all devices
IB/hfi1: Remove atomic operations for SDMA_REQ_HAVE_AHG bit
IB/hfi1: Use filedata rather than filepointer
IB/hfi1: Name function prototype parameters
IB/hfi1: Fix a subcontext memory leak
IB/hfi1: Return an error on memory allocation failure
IB/hfi1: Adjust default eager_buffer_size to 8MB
IB/hfi1: Get rid of divide when setting the tx request header
IB/hfi1: Fix yield logic in send engine
IB/hfi1, IB/rdmavt: Move r_adefered to r_lock cache line
IB/hfi1: Fix checks for Offline transient state
IB/ipoib: add get_link_ksettings in ethtool
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=eE4D
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add framework for supporting PCIe devices in Endpoint mode (Kishon
Vijay Abraham I)
- use non-postable PCI config space mappings when possible (Lorenzo
Pieralisi)
- clean up and unify mmap of PCI BARs (David Woodhouse)
- export and unify Function Level Reset support (Christoph Hellwig)
- avoid FLR for Intel 82579 NICs (Sasha Neftin)
- add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)
- short-circuit config access failures for disconnected devices (Keith
Busch)
- remove D3 sleep delay when possible (Adrian Hunter)
- freeze PME scan before suspending devices (Lukas Wunner)
- stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)
- disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)
- add arch-specific alignment control to improve device passthrough by
avoiding multiple BARs in a page (Yongji Xie)
- add sysfs sriov_drivers_autoprobe to control VF driver binding
(Bodong Wang)
- allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)
- fix crashes when unbinding host controllers that don't support
removal (Brian Norris)
- add driver for MicroSemi Switchtec management interface (Logan
Gunthorpe)
- add driver for Faraday Technology FTPCI100 host bridge (Linus
Walleij)
- add i.MX7D support (Andrey Smirnov)
- use generic MSI support for Aardvark (Thomas Petazzoni)
- make Rockchip driver modular (Brian Norris)
- advertise 128-byte Read Completion Boundary support for Rockchip
(Shawn Lin)
- advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)
- convert atomic_t to refcount_t in HV driver (Elena Reshetova)
- add CPU IRQ affinity in HV driver (K. Y. Srinivasan)
- fix PCI bus removal in HV driver (Long Li)
- add support for ThunderX2 DMA alias topology (Jayachandran C)
- add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)
- add ITE 8893 bridge DMA alias quirk (Jarod Wilson)
- restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
(Manish Jaggi)
* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
PCI: Don't allow unbinding host controllers that aren't prepared
ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
MAINTAINERS: Add PCI Endpoint maintainer
Documentation: PCI: Add userguide for PCI endpoint test function
tools: PCI: Add sample test script to invoke pcitest
tools: PCI: Add a userspace tool to test PCI endpoint
Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
misc: Add host side PCI driver for PCI test function device
PCI: Add device IDs for DRA74x and DRA72x
dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
PCI: dwc: dra7xx: Workaround for errata id i870
dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
PCI: dwc: dra7xx: Add EP mode support
PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
dt-bindings: PCI: Add DT bindings for PCI designware EP mode
PCI: dwc: designware: Add EP mode support
Documentation: PCI: Add binding documentation for pci-test endpoint function
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: imx6: Fix spelling mistake: "contol" -> "control"
...
This typo is quite common. Fix it and add it to the spelling file so
that checkpatch catches it earlier.
Link: http://lkml.kernel.org/r/20170317011131.6881-2-sboyd@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
momery||memory
Link: http://lkml.kernel.org/r/20170317011131.6881-1-sboyd@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let the target core check the CMD_T_ABORTED flag instead of the SRP
target driver. Hence remove the transport_check_aborted_status()
call. Since state == SRPT_STATE_CMD_RSP_SENT is something that really
should not happen, do not try to recover if srpt_queue_response() is
called for an I/O context that is in that state. This patch is a bug
fix because the srpt_abort_cmd() call is misplaced - if that function
is called from srpt_queue_response() it should either be called
before the command state is changed or after the response has been
sent.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware drivers
from Google, more auxdisplay drivers, extcon drivers, fpga drivers, and
a bunch of other driver updates. Nothing major, except if you happen to
have the hardware for these drivers, and then you will be happy :)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvAgg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yknsACgzkAeyz16Z97J3UTaeejbR7nKUCAAoKY4WEHY
8O9f9pr9gj8GMBwxeZQa
=OIfB
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware
drivers from Google, more auxdisplay drivers, extcon drivers, fpga
drivers, and a bunch of other driver updates. Nothing major, except if
you happen to have the hardware for these drivers, and then you will
be happy :)
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (136 commits)
firmware: google memconsole: Fix return value check in platform_memconsole_init()
firmware: Google VPD: Fix return value check in vpd_platform_init()
goldfish_pipe: fix build warning about using too much stack.
goldfish_pipe: An implementation of more parallel pipe
fpga fr br: update supported version numbers
fpga: region: release FPGA region reference in error path
fpga altera-hps2fpga: disable/unprepare clock on error in alt_fpga_bridge_probe()
mei: drop the TODO from samples
firmware: Google VPD sysfs driver
firmware: Google VPD: import lib_vpd source files
misc: lkdtm: Add volatile to intentional NULL pointer reference
eeprom: idt_89hpesx: Add OF device ID table
misc: ds1682: Add OF device ID table
misc: tsl2550: Add OF device ID table
w1: Remove unneeded use of assert() and remove w1_log.h
w1: Use kernel common min() implementation
uio_mf624: Align memory regions to page size and set correct offsets
uio_mf624: Refactor memory info initialization
uio: Allow handling of non page-aligned memory regions
hangcheck-timer: Fix typo in comment
...
Callers of rxe_mem_copy() provide pointer to store updated CRC
value. That pointer was supposed to be updated, but the
commit cee2688e3c ("IB/rxe: Offload CRC calculation when possible")
mistakenly removed that assignment for RXE_MEM_TYPE_DMA memory type.
The code worked because there are no actual callers with
RXE_MEM_TYPE_DMA, who are interested in returned value of crcp.
The one caller in read_reply(), who uses the returned crcp didn't
set RXE_MEM_TYPE_DMA as mem->type.
Fixes: cee2688e3c ("IB/rxe: Offload CRC calculation when possible")
Reported-by: Andrew Boyer <andrew.boyer@dell.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Andrew Boyer <andrew.boyer@dell.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The error path for context initialization is not consistent. Cleanup all
resources on failure.
Removed unused variable user_event_mask.
Add the _BASE_FAILED bit to the event flags so that a base context can
notify waiting sub contexts that they cannot continue.
Running out of sub contexts is an EBUSY result, not EINVAL.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The current algorithm for generating sub-context IDs is FILO. If the
contexts are not closed in that order, the uniqueness of the ID will be
compromised. I.e. logging the creation/deletion of context IDs with an
application that assigns and closes in a FIFO order reveals:
cache_id: assign: uctxt: 3 sub_ctxt: 0
cache_id: assign: uctxt: 3 sub_ctxt: 1
cache_id: assign: uctxt: 3 sub_ctxt: 2
cache_id: close: uctxt: 3 sub_ctxt: 0
cache_id: assign: uctxt: 3 sub_ctxt: 2 <<<
The sub_ctxt ID 2 is reused incorrectly.
Update the sub-context ID assign algorithm to use a bitmask of in_use
contexts. The new algorithm will allow the contexts to be closed in any
order, and will only re-use unused contexts.
Size subctxt and subctxt_cnt to match the user API size.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Context initialization mixes base context init with sub context init.
This is bad because contexts can be reused, and on reuse, reinit things
that should not re-initialized.
Normalize comments and function names to refer to base context and
sub context (not main, shared or slaves).
Separate the base context initialization from sub context initialization.
hfi1_init_ctxt() cannot return an error so changed to a void and remove
error message.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In the close path the context is removed from the device array, and then
the clear pkey function is called. The pkey function trys to get the
context from the device array, but because it was removed the clearing
does not occur.
Rework pkey clear function to work as expected. Update the function
variable to reflect the correct size and name of the hw_context.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The search for available shared contexts walks each registered hfi1
device. This search is too broad because other devices may not
be on the same fabric, and using its contexts could cause unexpected
behavior.
Removed walking the list of devices, limiting the search to the opened
device. With the device walk removed, the hfi1_devdata (dd) is not
available. Added it to the hfi1_filedata for reference.
With this change, hfi1_count_units() was rendered obsolete and was
removed.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The AHG index is only accessed in the request call
from user space, so there's no need for atomic semantics.
Replace atomic operations for SDMA_REQ_HAVE_AHG bit
with a test of the AHG index.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Since almost all functions that use the hfi1_filedata get the pointer
from the file pointer, simplify by only passing the hfi1_filedata pointer.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To improve the readability of function prototypes, give the parameters
names.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The only context that frees user_exp_rcv data structures is the last
context closed (from a sub-context set). This leaks the allocations
from the other sub-contexts. Separate the common frees from the
specific frees and call them at the appropriate time.
Using KEDR to check for memory leaks we get:
Before test:
[leak_check] Possible leaks: 25
After test:
[leak_check] Possible leaks: 31 (6 leaked data structures)
After patch applied (before and after test have the same value)
[leak_check] Possible leaks: 25
Each leak is 192 + 13440 + 6720 = 20352 bytes per sub-context.
Cc: stable@vger.kernel.org
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the eager buffer allocation fails, it is necessary to return
an error code.
Cc: stable@vger.kernel.org
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Performance analysis shows benefits for PSM2 in increasing eager buffer
size from 2MB to 8MB. The change has neutral impact on verbs.
Make change to the module parameter's default value. Allocation
ring down was verified to work with the larger buffer size.
Reviewed-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Tymoteusz Kielan <tymoteusz.kielan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Div instructions show costly in profiles when
the tx request header is set. Using right shift
instead of a divide operation reduces the cycles
spent in the function that sets the tx request
header as shown in the profile. Use right shift
operation instead.
Profile before change:
43.24% 009
|
|--23.41%-- user_sdma_send_pkts
| |
| |--99.90%-- hfi1_user_sdma_process_requestAfter:
Profile after change:
45.75% 009
|
|--14.81%-- user_sdma_send_pkts
| |
| |--99.95%-- hfi1_user_sdma_process_request
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When there are many RC QPs and an RDMA READ request
is sent, timeouts occur on the requester side because
of fairness among RC QPs on their relative SDMA engine
on the responder side. This also hits write and send, but
to a lesser extent.
Complicating the issue is that the current code checks if workqueue
is congested before scheduling other QPs, however, this
check is based on the number of active entries in the
workqueue, which was found to be too big to for
workqueue_congested() to be effective.
Fix by reducing the number of active entries as revealed by
experimentation from the default of num_sdma to
HFI1_MAX_ACTIVE_WORKQUEUE_ENTRIES. Retry counts were monitored
to determine the correct value.
Tracing to investigate any future issues is also added.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This field is causing excessive cache line bouncing.
There are spare bytes in the r_lock cache line so the best approach
is to make an rvt QP field and remove from the hfi1 priv field.
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In goto_offline() function pstate is masked by 0xff when compared
to PLS_OFFLINE state. Mask should be 0xf0, since upper 4 bits
specify the "major" state.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to let the bonding driver report the correct speed
of the underlaying interfaces, when they are IPoIB, the ethtool
function get_link_ksettings() in the IPoIB driver is implemented.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Suggested-by: Håkon Bugge <Haakon.Bugge@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Enable mlx5 IPoIB acceleration by declaring
mlx5_ib_{alloc,free}_rdma_netdev and assigning the mlx5
IPoIB rdma_netdev callbacks.
In addition, this patch brings in sync mlx5's IPoIB parts for net and IB
trees. As a precaution, we disabled IPoIB acceleration by default (in
the mlx5_core Kconfig file).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
With commit eea40b8f62 ("infiniband: call ipv6 route lookup
via the stub interface"), if the route lookup fails due to
ipv6 being disabled, the dst variable is left untouched, and
the following dst_release() may access uninitialized memory.
Since ipv6_dst_lookup() always sets dst to NULL in case of
lookup failure with ipv6 enabled, fix the above just
returning the error code if the lookup fails.
Fixes: eea40b8f62 ("infiniband: call ipv6 route lookup via the stub interface")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Doug Ledford <dledford@redhat.com>
