o Do not enable mailbox polling in case of legacy interrupt.
Process mailbox AEN/response from the interrupt.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Allow driver to collect firmware dump, during a forced firmware dump
operation, when auto firmware recovery is disabled. Also, during this
operation, driver should not allow reset recovery to be performed.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use vzalloc() instead of kzalloc() for allocation of
bootloader size memory. kzalloc() may fail to allocate
the size of bootloader
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Current code was not allowing the user to configure more
than one Tx ring using ethtool for 83xx/84xx adapter.
This regression was introduced by commit id
18afc102fd ("qlcnic: Enable
multiple Tx queue support for 83xx/84xx Series adapter.")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o TSS/RSS ring validation does not take into account that either
of these ring values can be 0. This patch fixes this validation
and would fail set_channel operation if any of these ring value
is 0. This regression was added as part of commit id
34e8c406fd ("qlcnic: refactor Tx/SDS
ring calculation and validation in driver.")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver should re-allocate all Tx queues after completing
diagnostic tests. This regression was added by commit id
c2c5e3a068 ("qlcnic: Enable
diagnostic test for multiple Tx queues.")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver was using netif_tx_{stop,wake}_all_queues() api
during link change event. Remove these api calls to
manage queue start/stop event, as core networking stack
will manage this based on netif_carrier_{on,off} call.
These API's were modified as part of commit id
012ec81223 ("qlcnic: Multi Tx
queue support for 82xx Series adapter.")
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using dt resources retrieval (interrupts and reg properties) there is
no predefined order for these resources in the platform dev resources
table.
Retrieve resources using platform_get_resource and platform_get_irq
functions instead of direct resource table entries to avoid resource type
mismatch.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return -EPROTO error if fragments detected in checksum_setup_ip().
Fixes: 1431fb31ec ('xen-netback: fix fragment detection in checksum setup')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The neighbour code sends up an RTM_NEWNEIGH netlink notification if
the NUD state of a neighbour cache entry is changed by a timer (e.g.
from REACHABLE to STALE), even if the lladdr of the entry has not
changed.
But an administrative change to the the NUD state of a neighbour cache
entry that does not change the lladdr (e.g. via "ip -4 neigh change
... nud ...") does not trigger a netlink notification. This means
that netlink listeners will not hear about administrative NUD state
changes such as from a resolved state to PERMANENT.
This patch changes the neighbor code to generate an RTM_NEWNEIGH
message when the NUD state of an entry is changed administratively.
Signed-off-by: Bob Gilligan <gilligan@aristanetworks.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the callback functions that upload the firmware in the comedi
drivers return a positive value indicating the number of bytes sent
to the device. Detect this condition and just return '0' to indicate
a successful upload.
Reported-by: Bernd Porr <mail@berndporr.me.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ian Abbott <abbotti@mev.co.uk>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At some point, Measurement Computing / ComputerBoards redesigned the
PCI-DIO48H to use a PLX PCI interface chip instead of an AMCC chip.
This meant they had to put their hardware registers in the PCI BAR 2
region instead of PCI BAR 1. Unfortunately, they kept the same PCI
device ID for the new design. This means the driver recognizes the
newer cards, but doesn't work (and is likely to screw up the local
configuration registers of the PLX chip) because it's using the wrong
region.
Since the PCI subvendor and subdevice IDs were both zero on the old
design, but are the same as the vendor and device on the new design, we
can tell the old design and new design apart easily enough. Split the
existing entry for the PCI-DIO48H in `pci_8255_boards[]` into two new
entries, referenced by different entries in the PCI device ID table
`pci_8255_pci_table[]`. Use the same board name for both entries.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stablle <stable@vger.kernel.org> # 3.10.y # 3.11.y # 3.12.y # 3.13.y
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Fix for a bug in the new cm36651 driver where it told the IIO driver it
was providing a decimal part, but then didn't. Now it correctly tells the
IIO core that it is only providing an integer value. This prevents random
incorrect values being output on a sysfs read.
* 3 fixes where drivers were miss specifying the endianness of their channels
as output through the buffer interface. These were discovered whilst
removing the terrible IIO_ST macro once and for all. The result is that
userspace may be informed that the buffer elements are being output as
little endian (on little endian platforms) when infact they are big endian.
Thus userspace will handle them incorrectly. This incorrect buffer
element specification is provided as sysfs attributes under
iio:deviceN/scan_elements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=CtIO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.13c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Third set of fixes for IIO in the 3.13 cycle.
* Fix for a bug in the new cm36651 driver where it told the IIO driver it
was providing a decimal part, but then didn't. Now it correctly tells the
IIO core that it is only providing an integer value. This prevents random
incorrect values being output on a sysfs read.
* 3 fixes where drivers were miss specifying the endianness of their channels
as output through the buffer interface. These were discovered whilst
removing the terrible IIO_ST macro once and for all. The result is that
userspace may be informed that the buffer elements are being output as
little endian (on little endian platforms) when infact they are big endian.
Thus userspace will handle them incorrectly. This incorrect buffer
element specification is provided as sysfs attributes under
iio:deviceN/scan_elements.
This patch fixes a build failure that appeared in v3.13-rc4 due to an
RTC/MFD update merged via -mm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSr0jGAAoJELSic+t+oim9bWsP/26SiYoI/ulG76GyJQuPVuWj
21fRM0TEZaSVxZf4lzZahdak9kDg5wDFX15ii9PnIPJ8m5Nz5lHKLaKMXUEY8saA
9vUZBsZNVbyQ9i7uH1/3mPC1fA+3XqwXKPrp4roIv5kFYCRFD+NDyBoCwl/FNvTE
u72A9nmojJv6C0UuExFtyXRiJnAn2goXYQ0JvlFKrezv7yStNGNXakIH1za1gEOq
hdMIkJ9r5/jZFIGKr7SHZjsGYqwngKfVfaSdBeWZqp6Z0FHf7MRI6aJ/TcwpkLFH
HNezPznw1/CzAHmHAyszbcIMIh/GHxJzDldUr4g+kwForjJGaYIcrimxFPtcmW9P
MhJ5DdO765aqp24cImo1aNJXMnJYTFDguMWSCWLwxNSmlpQYg2iEiKF2astcCb+p
3v4cj9EYnEiPdKwSmA/kCb7fiEnefHm8vLMgRZwXIXiDfDSub4JPya+L4SxHFMAZ
OxZyk/ZGPNkDAsyKUx3KQMw4Gmvbro/TJMLn73CgdrW++39/CbSzl5hM8oRMpeMn
LTvBQOViAODlODQDI9B1gOqd4c/9zE1wGgY64rE7MtzlhlcPNhXYjL/Cb7+JNZ49
Mp6nxt/yH7rlFMdpIC0GgsgBP4ilh3GeLDZDi+AhnbD1773Yn/mCA4cohfpUug6j
Yme3Jd3/zWHrUkUPjkfO
=t/v5
-----END PGP SIGNATURE-----
Merge tag 's2mps11-build' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator/clk fix from Mark Brown:
"Fix s2mps11 build
This patch fixes a build failure that appeared in v3.13-rc4 due to an
RTC/MFD update merged via -mm"
* tag 's2mps11-build' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
mfd: s2mps11: Fix build after regmap field rename in sec-core.c
Note this also sets the endianness to big endian whereas it would
previously have defaulted to the cpu endian. Hence technically
this is a bug fix on LE platforms.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@vger.kernel.org
Pull scheduler fixes from Ingo Molnar:
"Three fixes for scheduler crashes, each triggers in relatively rare,
hardware environment dependent situations"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Rework sched_fair time accounting
math64: Add mul_u64_u32_shr()
sched: Remove PREEMPT_NEED_RESCHED from generic code
sched: Initialize power_orig for overlapping groups
A single channel in this driver was using the IIO_ST macro.
This does not provide a parameter for setting the endianness of
the channel. Thus this channel will have been reported as whatever
is the native endianness of the cpu rather than big endian. This
means it would be incorrect on little endian platforms.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@vger.kernel.org
This driver sets the shift value equal to IIO_BE (or 1) rather than setting
that to 0 and specificying the endianness. This means the channel type is
missreported as
[be|le]:u16/16>>1 where the be|le is dependent on the cpu native endianness,
rather than
be:u16/16>>0 resulting in any userspace code using this information, miss
converting the channel and generating thoroughly trashed data.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@vger.kernel.org
Pablo Neira Ayuso says:
====================
The following patchset contains two Netfilter fixes for your net
tree, they are:
* Fix endianness in nft_reject, the NFTA_REJECT_TYPE netlink attributes
was not converted to network byte order as needed by all nfnetlink
subsystems, from Eric Leblond.
* Restrict SYNPROXY target to INPUT and FORWARD chains, this avoid a
possible crash due to misconfigurations, from Patrick McHardy.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to the set_peek_off patch where calling bind while the
socket is stuck in unix_dgram_recvmsg() will block and cause a hung task
spew after a while.
This is also the last place that did a straightforward mutex_lock(), so
there shouldn't be any more of these patches.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the IPsec git trees and some pure IPsec modules
to the IPsec section in the MAINTAINERS file.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using sk_dst_lock from softirq context is not supported right now.
Instead of adding BH protection everywhere,
udp_sk_rx_dst_set() can instead use xchg(), as suggested
by David.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: 9750223102 ("udp: ipv4: must add synchronization in udp_sk_rx_dst_set()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Driver bug fixes for SH PFC, TWL4030, MSM and RCAR.
- Update the MAINTAINERS
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=V2Cs
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"All but one are long-standing bug fixes that are also tagged for
stable
- Driver bug fixes for SH PFC, TWL4030, MSM and RCAR.
- Update the MAINTAINERS"
* tag 'gpio-v3.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: rcar: Fix level interrupt handling
gpio: msm: Fix irq mask/unmask by writing bits instead of numbers
gpio: twl4030: Fix regression for twl gpio LED output
sh-pfc: Fix PINMUX_GPIO macro
MAINTAINERS: update GPIO maintainers entry
Pull two Ceph fixes from Sage Weil:
"One of these is fixing a regression from the d_flags file type patch
that went into -rc1 that broke instantiation of inodes and dentries
(we were doing dentries first). The other is just an off-by-one
corner case"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: Avoid data inconsistency due to d-cache aliasing in readpage()
ceph: initialize inode before instantiating dentry
There's a possible deadlock if we flush the peers notifying work during setting
mtu:
[ 22.991149] ======================================================
[ 22.991173] [ INFO: possible circular locking dependency detected ]
[ 22.991198] 3.10.0-54.0.1.el7.x86_64.debug #1 Not tainted
[ 22.991219] -------------------------------------------------------
[ 22.991243] ip/974 is trying to acquire lock:
[ 22.991261] ((&(&net_device_ctx->dwork)->work)){+.+.+.}, at: [<ffffffff8108af95>] flush_work+0x5/0x2e0
[ 22.991307]
but task is already holding lock:
[ 22.991330] (rtnl_mutex){+.+.+.}, at: [<ffffffff81539deb>] rtnetlink_rcv+0x1b/0x40
[ 22.991367]
which lock already depends on the new lock.
[ 22.991398]
the existing dependency chain (in reverse order) is:
[ 22.991426]
-> #1 (rtnl_mutex){+.+.+.}:
[ 22.991449] [<ffffffff810dfdd9>] __lock_acquire+0xb19/0x1260
[ 22.991477] [<ffffffff810e0d12>] lock_acquire+0xa2/0x1f0
[ 22.991501] [<ffffffff81673659>] mutex_lock_nested+0x89/0x4f0
[ 22.991529] [<ffffffff815392b7>] rtnl_lock+0x17/0x20
[ 22.991552] [<ffffffff815230b2>] netdev_notify_peers+0x12/0x30
[ 22.991579] [<ffffffffa0340212>] netvsc_send_garp+0x22/0x30 [hv_netvsc]
[ 22.991610] [<ffffffff8108d251>] process_one_work+0x211/0x6e0
[ 22.991637] [<ffffffff8108d83b>] worker_thread+0x11b/0x3a0
[ 22.991663] [<ffffffff81095e5d>] kthread+0xed/0x100
[ 22.991686] [<ffffffff81681c6c>] ret_from_fork+0x7c/0xb0
[ 22.991715]
-> #0 ((&(&net_device_ctx->dwork)->work)){+.+.+.}:
[ 22.991715] [<ffffffff810de817>] check_prevs_add+0x967/0x970
[ 22.991715] [<ffffffff810dfdd9>] __lock_acquire+0xb19/0x1260
[ 22.991715] [<ffffffff810e0d12>] lock_acquire+0xa2/0x1f0
[ 22.991715] [<ffffffff8108afde>] flush_work+0x4e/0x2e0
[ 22.991715] [<ffffffff8108e1b5>] __cancel_work_timer+0x95/0x130
[ 22.991715] [<ffffffff8108e303>] cancel_delayed_work_sync+0x13/0x20
[ 22.991715] [<ffffffffa03404e4>] netvsc_change_mtu+0x84/0x200 [hv_netvsc]
[ 22.991715] [<ffffffff815233d4>] dev_set_mtu+0x34/0x80
[ 22.991715] [<ffffffff8153bc2a>] do_setlink+0x23a/0xa00
[ 22.991715] [<ffffffff8153d054>] rtnl_newlink+0x394/0x5e0
[ 22.991715] [<ffffffff81539eac>] rtnetlink_rcv_msg+0x9c/0x260
[ 22.991715] [<ffffffff8155cdd9>] netlink_rcv_skb+0xa9/0xc0
[ 22.991715] [<ffffffff81539dfa>] rtnetlink_rcv+0x2a/0x40
[ 22.991715] [<ffffffff8155c41d>] netlink_unicast+0xdd/0x190
[ 22.991715] [<ffffffff8155c807>] netlink_sendmsg+0x337/0x750
[ 22.991715] [<ffffffff8150d219>] sock_sendmsg+0x99/0xd0
[ 22.991715] [<ffffffff8150d63e>] ___sys_sendmsg+0x39e/0x3b0
[ 22.991715] [<ffffffff8150eba2>] __sys_sendmsg+0x42/0x80
[ 22.991715] [<ffffffff8150ebf2>] SyS_sendmsg+0x12/0x20
[ 22.991715] [<ffffffff81681d19>] system_call_fastpath+0x16/0x1b
This is because we hold the rtnl_lock() before ndo_change_mtu() and try to flush
the work in netvsc_change_mtu(), in the mean time, netdev_notify_peers() may be
called from worker and also trying to hold the rtnl_lock. This will lead the
flush won't succeed forever. Solve this by not canceling and flushing the work,
this is safe because the transmission done by NETDEV_NOTIFY_PEERS was
synchronized with the netif_tx_disable() called by netvsc_change_mtu().
Reported-by: Yaju Cao <yacao@redhat.com>
Tested-by: Yaju Cao <yacao@redhat.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc fixes from Ben Herrenschmidt:
"Uli's patch fixes a regression in ptrace caused by a mis-merge of a
previous LE patch. The rest are all more endian fixes, all fairly
trivial, found during testing of 3.13-rc's"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/powernv: Fix OPAL LPC access in Little Endian
powerpc/powernv: Fix endian issue in opal_xscom_read
powerpc: Fix endian issues in crash dump code
powerpc/pseries: Fix endian issues in MSI code
powerpc/pseries: Fix PCIE link speed endian issue
powerpc/pseries: Fix endian issues in nvram code
powerpc/pseries: Fix endian issues in /proc/ppc64/lparcfg
powerpc: Fix topology core_id endian issue on LE builds
powerpc: Fix endian issue in setup-common.c
powerpc: PTRACE_PEEKUSR always returns FPR0
If a user calls 'cpupower set --perf-bias 15', the process will end with
a SIGSEGV in libc because cpupower-set passes a NULL optarg to the atoi
call. This is because the getopt_long structure currently has all of
the options as having an optional_argument when they really have a
required argument. We change the structure to use required_argument to
match the short options and it resolves the issue.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=1000439
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Thomas Renninger <trenn@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With block processing of echoed output, observed output order is still
required. Push completed echoes and echo commands prior to output.
Introduce echo_mark echo buffer index, which tracks completed echo
commands; ie., those submitted via commit_echoes but which may not
have been committed. Ensure that completed echoes are output prior
to subsequent terminal writes in process_echoes().
Fixes newline/prompt output order in cooked mode shell.
Cc: <stable@vger.kernel.org> # 3.12.x : 39434ab n_tty: Fix missing newline echo
Reported-by: Karl Dahlke <eklhad@comcast.net>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Karl Dahlke <eklhad@comcast.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer Intel PCHs with LPSS have the same Designware controllers than
Haswell but ACPI IDs are different. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the clock properties required by the at91 usart driver.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark the function hvc_poll_init() as static in hvc/hvc_console.c because
it is not used outside this file.
This eliminates the following warning in hvc/hvc_console.c:
drivers/tty/hvc/hvc_console.c:791:5: warning: no previous prototype for ‘hvc_poll_init’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marks the functions gsm_cleanup_mux(), gsm_activate_mux(),
gsm_free_mux(), gsm_alloc_mux() and gsm_change_mtu() as static in
n_gsm.c because they are not used outside this file.
Also, drop the EXPORT_SYMBOL_GPL for the above mentioned functions
because nothing else in the kernel calls them.
This eliminates the following warnings in n_gsm.c:
drivers/tty/n_gsm.c:2022:6: warning: no previous prototype for ‘gsm_cleanup_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2076:5: warning: no previous prototype for ‘gsm_activate_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2120:6: warning: no previous prototype for ‘gsm_free_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2156:17: warning: no previous prototype for ‘gsm_alloc_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2714:5: warning: no previous prototype for ‘gsm_change_mtu’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When falling back from DMA to interrupt mode the receive interrupt has to
be re-enabled to catch new incoming data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In pl011_rx_chars() if pl011_dma_rx_trigger_dma() succeeds it will disable
the receive interrupt, no need to do this again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During initialisation, a UART may already be in use for a console, so
take care to preserve things like baud rate and data format to avoid
corrupting console output.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code to cope with a split tx/rx LCR_H register is non-trivial
so put it into it's own function to avoid duplication.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the pl011 is being used for a console, pl011_console_write forces
the control register (CR) to enable the UART for transmission and then
restores this to the original value afterwards. It does this while
holding the port lock.
Unfortunately, when the uart is started or shutdown - say in response to
userland using the serial device for a terminal - then this updates the
control register without any locking.
This means we can have
pl011_console_write Save CR
pl011_startup Initialise CR, e.g. enable receive
pl011_console_write Restore old CR with receive not enabled
this result is a serial port which doesn't respond to any input.
A similar race in reverse could happen when the device is shutdown.
We can fix these problems by taking the port lock when updating CR.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 17438217a6 on request
of Linus Walleij:
Greg can you please drop or revert
commit 17438217a6
"serial: pl011: use DMA RX polling by default"
from the TTY tree until this has been sorted out?
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
readline() inadvertently triggers an error recovery path when
pastes larger than 4k overrun the line discipline buffer. The
error recovery path discards input when the line discipline buffer
is full and operating in canonical mode and no newline has been
received. Because readline() changes the termios to non-canonical
mode to read the line char-by-char, the line discipline buffer
can become full, and then when readline() restores termios back
to canonical mode for the caller, the now-full line discipline
buffer triggers the error recovery.
When changing termios from non-canon to canon mode and the read
buffer contains data, simulate an EOF push _without_ the
DISABLED_CHAR in the read buffer.
Importantly for the readline() problem, the termios can be
changed back to non-canonical mode without changes to the read
buffer occurring; ie., as if the previous termios change had not
happened (as long as no intervening read took place).
Preserve existing userspace behavior which allows '\0's already
received in non-canon mode to be read as '\0's in canon mode
(rather than trigger add'l EOF pushes or an actual EOF).
Patch based on original proposal and discussion here
https://bugzilla.kernel.org/show_bug.cgi?id=55991
by Stas Sergeev <stsp@users.sourceforge.net>
Reported-by: Margarita Manterola <margamanterola@gmail.com>
Cc: Maximiliano Curia <maxy@gnuservers.com.ar>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Acked-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the devicetree documentation for the Cirrus Logic
CLPS711X UART.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a complex patch for refactoring CLPS711X serial driver.
Major changes:
- Eliminate <mach/hardware.h> usage.
- Devicetree support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the process is sleeping at the SNDRV_PCM_STATE_PAUSED
state from the wait_for_avail function, the sleep process will be woken by
timeout(10 seconds). Even if the sleep process wake up by timeout, by this
patch, the process will continue with sleep and wait for the other state.
Signed-off-by: JongHo Kim <furmuwon@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If we are doing aysnc writeback of metadata, we can get write errors
but have nobody to report them to. At the moment, we simply attempt
to reissue the write from io completion in the hope that it's a
transient error.
When it's not a transient error, the buffer is stuck forever in
this loop, and we cannot break out of it. Eventually, unmount will
hang because the AIL cannot be emptied and everything goes downhill
from them.
To solve this problem, only retry the write IO once before aborting
it. We don't throw the buffer away because some transient errors can
last minutes (e.g. FC path failover) or even hours (thin
provisioned devices that have run out of backing space) before they
go away. Hence we really want to keep trying until we can't try any
more.
Because the buffer was not cleaned, however, it does not get removed
from the AIL and hence the next pass across the AIL will start IO on
it again. As such, we still get the "retry forever" semantics that
we currently have, but we allow other access to the buffer in the
mean time. Meanwhile the filesystem can continue to modify the
buffer and relog it, so the IO errors won't hang the log or the
filesystem.
Now when we are pushing the AIL, we can see all these "permanent IO
error" buffers and we can issue a warning about failures before we
retry the IO. We can also catch these buffers when unmounting an
issue a corruption warning, too.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
When swalloc is specified as a mount option, allocations are
supposed to be aligned to the stripe width rather than the stripe
unit of the underlying filesystem. However, it does not do this.
What the implementation does is round up the allocation size to a
stripe width, hence ensuring that all allocations span a full stripe
width. It does not, however, ensure that that allocation is aligned
to a stripe width, and hence the allocations can span multiple
underlying stripes and so still see RMW cycles for things like
direct IO on MD RAID.
So, if the swalloc mount option is set, change the allocation
alignment in xfs_bmap_btalloc() to use the stripe width rather than
the stripe unit.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
The xfsbdstrat helper is a small but useless wrapper for xfs_buf_iorequest that
handles the case of a shut down filesystem. Most of the users have private,
uncached buffers that can just be freed in this case, but the complex error
handling in xfs_bioerror_relse messes up the case when it's called without
a locked buffer.
Remove xfsbdstrat and opencode the error handling in the callers. All but
one can simply return an error and don't need to deal with buffer state,
and the one caller that cares about the buffer state could do with a major
cleanup as well, but we'll defer that to later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
The function xfs_bmap_isaeof() is used to indicate that an
allocation is occurring at or past the end of file, and as such
should be aligned to the underlying storage geometry if possible.
Commit 27a3f8f ("xfs: introduce xfs_bmap_last_extent") changed the
behaviour of this function for empty files - it turned off
allocation alignment for this case accidentally. Hence large initial
allocations from direct IO are not getting correctly aligned to the
underlying geometry, and that is cause write performance to drop in
alignment sensitive configurations.
Fix it by considering allocation into empty files as requiring
aligned allocation again.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit f9b395a8ef)
When I tried to send the patches to XFS Maintainers,
I got returned mail included delivery fail message for Dave's mail.
Maybe, Dave Chinner mail address is incorrect.
I try to fix it correctly.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit db10bddc7d)
