The debug board is little different for all mxc 3-stack(PDK)
platforms, it is possible here to add a common implementation to
support this board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are some more conflicts than detected by git, namely support for
the newly added cpuimx machines needed to be converted to dynamic device
registration.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Conflicts:
arch/arm/mach-imx/Makefile
arch/arm/mach-imx/devices.c
arch/arm/mach-imx/devices.h
arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
arch/arm/mach-mx2/Kconfig
arch/arm/mach-mx25/Makefile
arch/arm/mach-mx25/devices.c
arch/arm/plat-mxc/include/mach/mx25.h
arch/arm/plat-mxc/include/mach/mxc_nand.h
cleaned up some duplicated mxc_gpio_mode calls and move the correpsonding
pin multiplexing either into the initial pin config table or ifdef blocks.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this one adds the frambuffer device and a TFT panel to the PhyCard-S
(pca100) board.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
These GPIO bank offsets are useful when define a gpio number.
E.G. when GPIO PORTC pin 6 is used for irq request pin of external
expanding device, we can define it like:
#define EXP_PARENT_IRQ_PIN (GPIO_PORTC + 6)
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add UART2 CTS/RTS and UART3 RXD/TXD pad definitons for imx51_3ds board,
add GPIO_1_6 definiton because this pin is used as a CPLD parent irq
request pin on imx51_3ds board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For pad EIM_D27 to work in UART3_RTS mode, the input path should be
3 instead of 0; for pad USBH1_STP to work in GPIO_1_27 mode, the mux
value should be 2 instead of 8.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pads capable of being used as GPIOs had their pad-name and mode-name
switched. Also, fix the following:
- Whitespace fixes
- Replace IOMUX_CONFIG_ALTn with 'n'
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The information in the i.MX25 Reference Manual is lacking. Add information from
the Freescale BSP.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
usb drivers need to get the right value for otg clock so
calculate and return it
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX25's OTG has the same USBCTRL registers than i.MX35 so reuse
most of the i.MX35's defines.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the standard place for this define is include/mach/mx25.h
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
when CONFIG_USB_ULPI is not defined we actually get :
warning: 'otg_pdata' defined but not used
warning: 'usbh2_pdata' defined but not used
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: s.hauer@pengutronix.de
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
without this patch, ipu_clk's value is 0 thus preventing mx3fb from
calculating the right divisor for pixel clock generator.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes the clock refcounting when reparenting is used.
Boot-tested on imx51 babbage board.
Sascha pointed out a good explanation of refcounting here:
http://www.spinics.net/lists/arm-kernel/msg85879.html
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The keymap is taken from the Freescale supplied kernel.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Like this one (if CONFIG_USB_ULPI is not set):
arch/arm/mach-mx3/mach-pcm043.c:312: warning: 'otg_pdata' defined but not used
arch/arm/mach-mx3/mach-pcm043.c:317: warning: 'usbh1_pdata' defined but not used
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Using the parent functions frame pointer to access our arguments is
completely wrong, whether or not we're building with frame pointers
or not. What we should be using is the stack pointer to get at the
word above the registers we stacked ourselves.
Reported-by: Bosko Radivojevic <bosko.radivojevic@gmail.com>
Tested-by: Bosko Radivojevic <bosko.radivojevic@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CC kernel/elfcore.o
In file included from include/linux/elf.h:7,
from kernel/elfcore.c:1:
arch/arm/include/asm/elf.h:124: warning: 'struct mm_struct' declared inside parameter list
arch/arm/include/asm/elf.h:124: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
My attempt to make the LEDs only compile for RealView and
Versatile was futile: I missed the Versatile Express. So invert
the logic and explicitly include the platforms to compile for.
Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds a simple driver supporting the new LED framework with
triggers and all for the RealView and Versatile platforms. The
RealView and Versatile platform drivers were arranged to compile
for all-but-integrator as a side effect since the Integrator has
a different LED driver.
Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
qnap_tsx1x_register_flash is only called by qnap_ts219_init and
qnap_ts41x_init which both live in .init.text, too. So the move is OK.
This fixes the following warning in kirkwood_defconfig:
WARNING: vmlinux.o(.text+0x9334): Section mismatch in reference from the function qnap_tsx1x_register_flash() to the variable .init.data:qnap_tsx1x_spi_slave_info
The function qnap_tsx1x_register_flash() references
the variable __initdata qnap_tsx1x_spi_slave_info.
This is often because qnap_tsx1x_register_flash lacks a __initdata
annotation or the annotation of qnap_tsx1x_spi_slave_info is wrong.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
the different putc variants used an initialized local static variable
which is broken since
5de813b (ARM: Eliminate decompressor -Dstatic= PIC hack)
This needs to be initialized at runtime and so needs to be global.
While at it give it a better name.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need mach/hardware.h for CLPS7111_VIRT_BASE.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mov rx, =<immediate> isn't valid, use #<immediate> instead.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need asm/memory.h for NS9XXX_CSxSTAT_PHYS (via mach/memory.h).
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IO_BASE shoule be IO_VIRT, and IO_START should be IO_PHYS. We also need
mach/hardware.h for these definitions.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - relax capability ID checks on newer hardware
Input: twl40300-keypad - fix handling of "all ground" rows
Input: gamecon - reference correct pad in gc_psx_command()
Input: gamecon - reference correct input device in NES mode
Input: w90p910_keypad - change platfrom driver name to 'nuc900-kpi'
Input: i8042 - add Gigabyte Spring Peak to dmi_noloop_table
Input: qt2160 - rename kconfig symbol name
Since the infrastructure for determining shift/mult values from a
clock rate and a minimum programmable rate is now in the kernel,
lets remove this custom code.
Cc: Deepak Saxena <dsaxena@plexity.net>
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a dummy clk definition for the APB pclk signal on all platforms
using the AMBA bus infrastructure. This ensures that these platforms
continue to work when the core amba bus code controls the APB pclk.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the infrastructure for determining shift/mult values from a
clock rate and a minimum programmable rate is now in the kernel,
lets remove this custom code.
Cc: Viresh KUMAR <viresh.kumar@st.com>
Tested-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Delete a wrong redundant right parenthesis in
arch/arm/mach-footbridge/common.c
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to modify spi flash configuration,
the previous one can make spi driver work failed.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add nuc900 kpi platform_device structure to nuc910_dev
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to add nuc900 keypad arch platform data.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch re-organizes the nuc900 lcd arch platform data,
remove the lcd platform data setting from nuc950.c to dev.c
It can maximize the share codes between nuc900 series MCUs.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to fix nuc900 touchscreen clk definition bug,the .dev_id's
name should be 'nuc900-ts', it should be the same to pdev.name. or else,
the touchscreen driver will be not working well due to clock engine disabled.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Nokia RX51 board code (arch/arm/mach-omap2/board-rx51-peripherals.c)
defines a key map for the matrix keypad keyboard. The hardware seems to
use all of the 8 rows and 8 columns of the keypad, although not all
possible locations are used.
The TWL4030 supports keypads with at most 8 rows and 8 columns. Most keys
are defined with a row and column number between 0 and 7, except
KEY(0xff, 2, KEY_F9),
KEY(0xff, 4, KEY_F10),
KEY(0xff, 5, KEY_F11),
which represent keycodes that should be emitted when entire row is
connected to the ground. since the driver handles this case as if we
had an extra column in the key matrix. Unfortunately we do not allocate
enough space and end up owerwriting some random memory.
Reported-and-tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds some platform data for the character LCD found in the
RealView and Versatile reference designs from ARM.
Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the vbus signal to optionally use polling. This is required if
the vbus signal is connected to an non-interrupting io expander for
example. If vbus is in polling mode, then it is assumed that the vbus
gpio may sleep. Also add an option to have vbus be an active low
signal. Both options are set in the platform data for the device.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If TCM is in use, we should display it in the virtual memory
layout along with everything else.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CPUs v6 and up support multiple TCM banks, for example an ITCM of
8k is supplied in two 4k banks. This makes the TCM work on the
1176JZF-S devchip.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The earlier TCM memory regions were mapped as MT_MEMORY_UNCACHED
which doesn't really work on platforms supporting the new v6
features like the NX bit. Add unique MT_MEMORY_[I|D]TCM types
instead.
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The code to support the DNS-323 rev C1 added a call to
phy_register_fixup_for_uid() and therefore phylib has to
be built in.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch add a LED class driver for the dual-GPIO LEDs found on the
Network Space v2 board (and parents). This include Internet Space v2,
Network Space (Max) v2 and d2 Network v2 boards.
This dual-GPIO LED is wired to a CPLD and can blink in relation with the
SATA activity. The driver expose this capability through a "sata" sysfs
attribute.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch extends the kirkwood's PCIe support up to 2 controllers as in the 6282 devices.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Add private_data pointer to the pci_sys_data, this pointer can be
used for holding platform specific data for each pci controller.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The 6282 SoC is compatible to 6280 and features faster CPU, DDR3, additional
PCIe interface, and LCD controller. More information can be found here:
http://www.marvell.com/products/processors/embedded/armada_300/armada_310.pdf
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
In case the board is configured to boot from spi flash, the mpps
will not be configured to select the NAND I/Os. This patch makes
sure to select the NAND I/O's regardless to the boot device type.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Some platforms, such as the DNS-323 rev C requires the soft reset line
to be toggled on and back off for the reset to work.
Note: The choice of 200ms delay comes from the 2.6.12 based vendor kernel.
It seems to be a -lot- though and I had my device working fine with much
smaller delays but better safe...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch adds the base support for this new HW revision to the existing
dns323-setup.c file. The SoC seems to be the same as rev B1, the GPIOs
are all wired differently though and the fan control isn't i2c based
anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch adds support for the OpenRD Ultimate machine (could be found
at http://www.arm.linux.org.uk/developer/machines/list.php?id=2884)
Signed-off-by: Dmytro Milinevskyy <milinevskyy@gmail.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Patch found in QNAPs vendor source package, with some cleanups
(proper defines, shortened max. timeout from 1s to 200ms).
Without this patch the PCIe SATA controller (Marvell 88sx7042/sata_mv)
in my QNAP TS-419P (Marvell 88f6281/Kirkwood) stops working after a
few minutes.
The symptomes are described in this thread:
http://marc.info/?l=linux-ide&m=124822863706181&w=2
[ Note: this is a workaround in need of a better analysis/solution -- NP ]
Acked-by: Saeed Bishara <saeed@marvell.com>
Tested-by: Bernhard R. Link <brl@pcpool00.mathematik.uni-freiburg.de>
Seconded-by: Martin Michlmayr <tbm@cyrius.com>
I'm_not_very_happy_with_it-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Add support for the HP t5325 Thin Client. This thin client is based
on a Marvell Kirkwood chip at 1.2 GHz and features 512 MB RAM, 512 MB
SATA-attached flash and an XGI Volari Z11 GPU.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
MPP44 can be used to differentiate between one-bay (TS-11x) and
two-bay (TS-21x) devices.
According to an engineer from QNAP, the setting of MPP44 depends
on the firmware rather than hardware. Presumably, this means
that you could fake the MPP44 value by changing the boot loader.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Add MPP definitions for Marvell Kirkwood 88F6282 revision.
Update some defines to reflect datasheet's MPP names.
Signed-off-by: Benjamin Zores <benjamin.zores@alcatel-lucent.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Among other changes, commit b2a731aa ("D-link DNS-323 revision A1 power
LED") changed the default behaviour of the power LED from solid to
blinking. This was done to match the original DNS-323 firmware which
blinks during the boot process and sets the LED to solid when booting
has completed. However, the downside of this behaviour is that it
requires userland code to change the LED, even for those who don't
care about the behaviour of the original firmware. Therefore, change
it to solid again and let those who care about the original behaviour
change the behaviour from userland.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
On the QNAP TS-41x, MPP45 is used to show the setting of jumper JP1.
Fix the documentation to explain what the settings really indicate.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Export GPIO 45 which is used to indicate the setting of the JP1
jumper. This is useful for userland tools, such as qcontrol, to
see whether the LCD or a serial console is connected.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Fix the following warning :
WARNING: vmlinux.o(.text+0x95a0): Section mismatch in reference from the
function qnap_tsx1x_register_flash() to the (unknown reference) .init.data:(unknown)
The function qnap_tsx1x_register_flash() references
the (unknown reference) __initdata (unknown).
This is often because qnap_tsx1x_register_flash lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Add a common early allocator function, in preparation for switching
over to LMB. When we do, this function will need to do a little more
than just allocating memory; we need it zero initialized too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The logic in this file is rather convoluted, but essentially:
1. region type 0 is SDRAM
2. referring to the code fragment
if (set_fbmem_region_type(&rg, OMAPFB_MEMTYPE_SDRAM,
sdram_start, sdram_size) < 0 ||
(rg.type != OMAPFB_MEMTYPE_SDRAM))
continue;
- if rg.type is not OMAPFB_MEMTYPE_SDRAM, set_fbmem_region_type()
returns zero immediately (since rg.type is non-zero), and so we
'continue'.
- if rg.type is OMAPFB_MEMTYPE_SDRAM, and rg.paddr is zero,
we fall through.
- if rg.type is OMAPFB_MEMTYPE_SDRAM, and the region lies within
SDRAM, we fall through.
- if rg.type is OMAPFB_MEMTYPE_SDRAM, and the region is not within
SDRAM, we 'continue'.
3. check_fbmem_region seems unnecessary.
- we know rg.type is OMAPFB_MEMTYPE_SDRAM
- we can check rg.size independently
- bootmem_reserve() can check for overlapping reservations itself
- we've already validated that the requested region lies within SDRAM.
4. avoid BUG()ing if the region entry is already set; print an error,
and mark the configuration invalid - at least we'll continue booting
so the error message has a chance of being logged/visible via serial
console.
With these changes in place, it makes the code much easier to understand
and hence easier to convert to LMB.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the platform specific bootmem memory reservations out of
arch/arm/mm/mmu.c into their respective platform files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Everything should now be using sparsemem rather than discontigmem, so
remove the code supporting discontigmem from ARM.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than storing the minimum size of the vmalloc area, store the
maximum permitted address of the vmalloc area instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds platform data for the PL022 to the ARM Versatile reference
design, and adds the necessary clock definition.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds platform data for the PL022 to the ARM RealView reference
designs, adds the necessary clock definition and fixes a badly
defined IRQ line on the PB1176.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Bin Yang <bin.yang@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Bin Yang <bin.yang@marvell.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The wrong CONFIG defines were checked, and the <mach/audio.h>
include was missing
Signed-off-by: pieter <p.grimmerink@inepro.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch:
1) Simpifies the DRI recomputation routine by pulling out the common code
2) Fixes a bug in PXA27x DRI recomputation caused by incorrect parenthesis
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'arm/defconfig/reduced-v2.6.35-rc1' of git://git.pengutronix.de/git/ukl/linux-2.6:
ARM: reduce defconfigs
This is a big change, but results in no loss of information, despite us
losing almost 200k lines:
177 files changed, 652 insertions(+), 194157 deletions(-)
and Grant Likely thinks powerpc can also use the same reduction
technique.
The python script that did the reduction looks like this:
#! /usr/bin/env python
# vim: set fileencoding=utf-8 :
# Copyright (C) 2010 by Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
import re
import subprocess
import os
import sys
# This prevents including a timestamp in the .config which makes comparing a
# bit easier.
os.environ['KCONFIG_NOTIMESTAMP'] = 'Yes, please'
# XXX: get these using getopt
kernel_tree = '' # os.path.join(os.environ['HOME'], 'gsrc', 'linux-2.6')
arch = 'arm'
target = sys.argv[1]
defconfig_src = os.path.join(kernel_tree, 'arch/%s/configs/%s' % (arch, target))
subprocess.check_call(['make', '-s', 'ARCH=%s' % arch, target])
origconfig = list(open('.config'))
config = list(origconfig)
config_size = os.stat('.config').st_size
i = 0
while i < len(config):
print 'test for %r' % config[i]
defconfig = open(defconfig_src, 'w')
defconfig.writelines(config[:i])
defconfig.writelines(config[i + 1:])
defconfig.close()
subprocess.check_call(['make', '-s', 'ARCH=%s' % arch, target])
if os.stat('.config').st_size == config_size and list(open('.config')) == origconfig:
del config[i]
else:
i += 1
defconfig = open(defconfig_src, 'w')
defconfig.writelines(config)
defconfig.close()
which is pretty self-explanatory.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As long as the zImage is placed within the 128MB range from the start of
memory, ZRELADDR (Address where the decompressed kernel will be placed,
usually == PHYS_OFFSET + TEXT_OFFSET) can be determined at run-time by
masking PC with 0xf80000000.
Running through all the Makefile.boot, all those zreladdr-y
addresses == 0x[0-f][08]00_0000 + TEXT_OFFSET can be determined at
run-time.
Option CONFIG_AUTO_ZRELADDR and CONFIG_ZRELADDR are introduced,
CONFIG_ZRELADDR _must_ be explicitly specified if:
- ((zreladdr-y - TEXT_OFFSET) & ~0xf8000000) != 0, which means
masking PC with 0xf8000000 will result in an incorrect address.
Currently this is only a problem on u300.
- or the assumption of the zImage being loaded by the bootloader within
the first 128MB of RAM is incorrect
- or when ZBOOT_ROM is used, where the above assumption is usually wrong.
[ukleinek: changed mask from 0xf0000000 to 0xf8000000 for mx1 and shark
+ some review fixes from the mailing list]
Original-Idea-and-Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CPU: Testing write buffer coherency: ok
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:3145 check_flags+0xcc/0x1dc()
Modules linked in:
[<c0035120>] (unwind_backtrace+0x0/0xf8) from [<c0355374>] (dump_stack+0x20/0x24)
[<c0355374>] (dump_stack+0x20/0x24) from [<c0060c04>] (warn_slowpath_common+0x58/0x70)
[<c0060c04>] (warn_slowpath_common+0x58/0x70) from [<c0060c3c>] (warn_slowpath_null+0x20/0x24)
[<c0060c3c>] (warn_slowpath_null+0x20/0x24) from [<c008f224>] (check_flags+0xcc/0x1dc)
[<c008f224>] (check_flags+0xcc/0x1dc) from [<c00945dc>] (lock_acquire+0x50/0x140)
[<c00945dc>] (lock_acquire+0x50/0x140) from [<c0358434>] (_raw_spin_lock+0x50/0x88)
[<c0358434>] (_raw_spin_lock+0x50/0x88) from [<c00fd114>] (set_task_comm+0x2c/0x60)
[<c00fd114>] (set_task_comm+0x2c/0x60) from [<c007e184>] (kthreadd+0x30/0x108)
[<c007e184>] (kthreadd+0x30/0x108) from [<c0030104>] (kernel_thread_exit+0x0/0x8)
---[ end trace 1b75b31a2719ed1c ]---
possible reason: unannotated irqs-on.
irq event stamp: 3
hardirqs last enabled at (2): [<c0059bb0>] finish_task_switch+0x48/0xb0
hardirqs last disabled at (3): [<c002f0b0>] ret_slow_syscall+0xc/0x1c
softirqs last enabled at (0): [<c005f3e0>] copy_process+0x394/0xe5c
softirqs last disabled at (0): [<(null)>] (null)
Fix this by ensuring that the lockdep interrupt state is manipulated in
the appropriate places. We essentially treat userspace as an entirely
separate environment which isn't relevant to lockdep (lockdep doesn't
monitor userspace.) We don't tell lockdep that IRQs will be enabled
in that environment.
Instead, when creating kernel threads (which is a rare event compared
to entering/leaving userspace) we have to update the lockdep state. Do
this by starting threads with IRQs disabled, and in the kthread helper,
tell lockdep that IRQs are enabled, and enable them.
This provides lockdep with a consistent view of the current IRQ state
in kernel space.
This also revert portions of 0d928b0b61
which didn't fix the problem.
Tested-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This parameter is used by primary kernel to pass address of vmcore
header to the dump capture kernel.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This function is used by vmcore code to read a page from the old
kernel memory.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we are crashing there is no indirection page in place. Only
control page is present.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement function machine_crash_shutdown() which disables IRQs and
saves machine state to ELF notes structure.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement machine specific function crash_setup_regs() which is
responsible for storing machine state when crash occured.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implemented ARM support for command line option
"crashkernel=size@start" which allows user to reserve some memory
for a dump capture kernel.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MTU wallclock timing fix-up patch was hardwired to the DB8500
causing a regression. This makes it work on the DB5500 as well.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The TLS register is only available on ARM1136 r1p0 and later.
Set HWCAP_TLS flags if hardware TLS is available and test for
it if CONFIG_CPU_32v6K is not set for V6.
Note that we set the TLS instruction in __kuser_get_tls
dynamically as suggested by Jamie Lokier <jamie@shareable.org>.
Also the __switch_to code is optimized out in most cases as
suggested by Nicolas Pitre <nico@fluxnic.net>.
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow SH-Mobile ARM users to adjust FORCE_MAX_ZONEORDER.
The Kconfig entry is taken from SH and non-4K page size
stuff has been trimmed away. For now only SH-Mobile ARM is
allowed to change this variable, SA1111 configs are kept at
"9" and the rest at "11".
CONFIG_FORCE_MAX_ZONEORDER lets the user tweak the maximum
amount of physically contiguous memory that can be allocated
by the kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MVFR0 and MVFR1 are only available starting with ARM1136 r1p0 release
according to "B.5 VFP changes" in DDI0211F_arm1136_r1p0_trm.pdf. This is
also when TLS register got added, so we can use HAS_TLS also to test for
MVFR0 and MVFR1.
Otherwise VFPFMRX and VFPFMXR access fails and we get:
Internal error: Oops - undefined instruction: 0 [#1]
PC is at no_old_VFP_process+0x8/0x3c
LR is at __und_svc+0x48/0x80
...
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch enables the HAVE_REGS_AND_STACK_ACCESS_API option
for ARM which is required by the kprobe events tracer. Code based
on the PowerPC port.
Cc: Jean Pihet <jpihet@mvista.com>
Tested-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
So to allow NR_IRQS to be dynamic and platforms to specify the number
of IRQs really needed.
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a number of basic fixes to the PB1176 that makes it tick
properly:
- Detect MMC insertion/removal even when PL061 GPIO is not compiled
in. The register to read this status directly is removed on the
PB1176.
- Define the UART3 on the DevChip (where is actually is) and define
the new UART4 serial port on the FPGA.
- Also define the clocks for these two UARTs apropriately.
- Remove the false notion that the PB1176 should have its CLCD
on the ISSP, this is not the case, it is in the DevChip.
- Remove the defintions and the previously commented-out PL081
DMAC. As confirmed by mail this was found to be broken on the
PB1176 board and removed from the subsequent FPGA images.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the Cortex-A9 local timers available when
using the CA9X4 daughterboard with the Versatile Express.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Bluewater Systems Snapper 9260/9G20 modules
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add definition for NR_BUILTIN_GPIO for AT91 family
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This rework allows to address tow memory controllers. AT91SAM9263 and
AT91SAM9G45 family have tow SDRAM or DDR/SDRAM controllers. Power management
should take care of this.
This patch modify the way RAM IP header files are implemented to allow
access to registers of both controllers ; it also adds some macros.
We also modify the power management files to use those modified header files.
Slow clock (assembly) and regular power management functions are synchronized
for setting of RAM self-refresh procedure:
(lpr & ~AT91_DDRSDRC_LPCB) | AT91_DDRSDRC_LPCB_SELF_REFRESH
Note that AT91RM9200 is not impacted by this modification.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, the 32-bit and 64-bit atomic operations on ARM do not
include memory constraints in the inline assembly blocks. In the
case of barrier-less operations [for example, atomic_add], this
means that the compiler may constant fold values which have actually
been modified by a call to an atomic operation.
This issue can be observed in the atomic64_test routine in
<kernel root>/lib/atomic64_test.c:
00000000 <test_atomic64>:
0: e1a0c00d mov ip, sp
4: e92dd830 push {r4, r5, fp, ip, lr, pc}
8: e24cb004 sub fp, ip, #4
c: e24dd008 sub sp, sp, #8
10: e24b3014 sub r3, fp, #20
14: e30d000d movw r0, #53261 ; 0xd00d
18: e3011337 movw r1, #4919 ; 0x1337
1c: e34c0001 movt r0, #49153 ; 0xc001
20: e34a1aa3 movt r1, #43683 ; 0xaaa3
24: e16300f8 strd r0, [r3, #-8]!
28: e30c0afe movw r0, #51966 ; 0xcafe
2c: e30b1eef movw r1, #48879 ; 0xbeef
30: e34d0eaf movt r0, #57007 ; 0xdeaf
34: e34d1ead movt r1, #57005 ; 0xdead
38: e1b34f9f ldrexd r4, [r3]
3c: e1a34f90 strexd r4, r0, [r3]
40: e3340000 teq r4, #0
44: 1afffffb bne 38 <test_atomic64+0x38>
48: e59f0004 ldr r0, [pc, #4] ; 54 <test_atomic64+0x54>
4c: e3a0101e mov r1, #30
50: ebfffffe bl 0 <__bug>
54: 00000000 .word 0x00000000
The atomic64_set (0x38-0x44) writes to the atomic64_t, but the
compiler doesn't see this, assumes the test condition is always
false and generates an unconditional branch to __bug. The rest of the
test is optimised away.
This patch adds suitable memory constraints to the atomic operations on ARM
to ensure that the compiler is informed of the correct data hazards. We have
to use the "Qo" constraints to avoid hitting the GCC anomaly described at
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=44492 , where the compiler
makes assumptions about the writeback in the addressing mode used by the
inline assembly. These constraints forbid the use of auto{inc,dec} addressing
modes, so it doesn't matter if we don't use the operand exactly once.
Cc: stable@kernel.org
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The atomic64_add_unless function compares an atomic variable with
a given value and, if they are not equal, adds another given value
to the atomic variable. The function returns zero if the addition
did not occur and non-zero otherwise.
On ARM, the return value is initialised to 1 in C code. Inline assembly
code then performs the atomic64_add_unless operation, setting the
return value to 0 iff the addition does not occur. This means that
when the addition *does* occur, the value of ret must be preserved
across the inline assembly and therefore requires a "+r" constraint
rather than the current one of "=&r".
Thanks to Nicolas Pitre for helping to spot this.
Cc: stable@kernel.org
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On i.MX35 the L2X0_AUX_CTRL register does not have sensible reset
default values. Allow them to be overwritten with the aux_val/aux_mask
arguments passed to l2x0_init().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The only reference in arch/arm/boot/compressed to PARAMS_PHYS is
params() in head.S, which can be directly converted to the exact
address as specified by arch/arm/mach-rpc/Makefile.boot.
Signed-off-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This was deprecated in 2001 and announced to live on for 5 years.
For now provide a kernel parameter for those who still need it.
Acked-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The only user of initrd_phys is arch/arm/boot/bootp/init.S which still
gets the value passed to.
Acked-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
I tried to get this running to debug the regression introduced by
e7db7b4 without success. But this has several problems that make it
hard to fix:
- lib/decompress_inflate.c includes in-kernel headers that make
it difficult to compile for user space.
- the binary formats changed both in kernel and user space and
at least for the kernel side there isn't only a single
variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Devkit8000 uses the TPS65930 and not the TWL4030.
The TPS65930 uses only a subset of the power supplies
of the TWL4030.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_board_config is no longer used and thats why empty.
This patch removes the empty omap_board_config.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Using the macro gpio_is_valid for check of valid gpio pins.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
devkit8000_panel_enable_tv and devkit8000_panel_disable_tv are already
done in DSS2 code. So they are no longer needed in board code.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Devkit8000 uses the cost reduced variant tps65930 of the twl4030.
The TPS65930 only has vdd1, vdd2, vpll1, vio, vmmc1, vdac and vaux2.
vaux2 is not used on Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VDVI power supply is no longer needed in
board code with the new DSS2 interface.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch corrects the LCD reset pin configuration.
Original code from early devkit8000 patch sets the TWL4030 GPIO_1
to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins
are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be
disabled when other display is turned on.
Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch corrects the DVI-D output setup of Devkit8000
Devkit8000 has different DVI reset pin with the BeagleBoard.
On Devkit8000 the TWL4030 GPIO_7 is assigned to do the job.
Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Corrected the wrong power supplies in devkit8000 code.
Add supply for ads7846 to support the new regulator framework for
touchscreen.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MACH_OMAP2_H4_USB1 doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MACH_OMAP_H4_OTG doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
APM doesn't exist in Kconfig, therefore removing all references for it
from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LEDS_OMAP_DEBUG doesn't exist in Kconfig, therefore replacing all
references for it with OMAP_DEBUG_LEDS from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_STI doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_DSP doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated to apply on top of already queued patches]
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_IR doesn't exist in Kconfig, therefore removing all references
for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated for new mux code]
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_MUX_ERRORS doesn't exist in Kconfig, therefore replacing all
references for it with OMAP_MUX_WARNINGS in the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use new mux functions for that. There are no other known 2430 boards
that need this mux.
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the new mux function for that.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we get pin muxing out of plat-omap and can convert H4 to use the
new mux functions.
Note that it should be safe to assume we can mux all the keypad pins
except on H4 which may have Menelaus connected.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make omap2 FS USB code use new mux functions. Do not mux usb2_tllse0
as it has multiple options.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add data for 2430. Big thanks to Paul Walmsley <paul@pwsan.com>
for generating usable mux data out of TRMs.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add data for 2420. Big thanks to Paul Walmsley <paul@pwsan.com>
for generating usable mux data out of TRMs.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like 24xx uses mode3 instead of mode4 for muxable GPIO pins.
This will be needed when 24xx mux code is converted to use the new
mux functions.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move omap2 FS USB platform init code into mach-omap2/usb-fs.c. This will
allow further work later on to use omap hwmod for initializing the
device.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to split old FS USB platform init code and stop doing pin multiplexing
under plat-omap. First move 24xx specific init code into omap2_usb[012]_init
functions.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes on wrong function name in include/plat/sdhci.h for Samsung.
The 's5pc100_default_sdhci0()' function should be chnaged to
's5pv210_default_sdhci0()'. Because 's5pv210_default_sdhci0()' must be pair.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The S5P6442 PLL setting announce message incorrectly displays S5P6440
as the SoC. Change it to S5P6442.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes the following compilation problem if only NCP machine
is selected:
arch/arm/mach-s3c64xx/s3c6410.c: In function 's3c6410_map_io':
arch/arm/mach-s3c64xx/s3c6410.c:51: error: implicit declaration of function 's3c6410_default_sdhci2'
And also adds missed 's3c6400_default_sdhci2'.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fix and added comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
1. Corrected shift values of I2S and UART clocks (CLK_GATE_IP3), which were
defined incorrectly.
2. Corrected shift values of sclk_audio, uclk1, sclk_fimd, sclk_mmc,
sclk_spi, sclk_pwm, which had duplicated .enable/.ctrlbit with their
twins defined in struct clk init_clocks_disable[] and struct clk
init_clocks[]. We've changed their .enable/.ctrlbit to use CLK_SRC_MASK
register to avoid the duplicated clock problem described below.
NOTE: Duplicated Clock Problem
Please note that each clock definition should access different control
register; otherwise, the system may suffer lockups. For example, if we
have two clock definitions "a" and "b" which access the same register
(and the shift value). Then, when we do:
module A
clk = clk_get("a");
clk->clk_enable(clk);
module B (context switch)
clk = clk_get("b");
clk->clk_enable(clk);
do something with clk.
clk->clk_disable(clk);
module A (context switch)
do something with clk
* At this point, the system may hang.
Therefore, there should be no clock definitions with the same contol
register/shift. If we need to create "aliases", then, creating child
clocks sharing the clock should be fine.
3. Corrected other sclk_* shift values and access registers.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title and message fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes bug on eint type set function, s5p_irq_eint_set_type().
In the IRQ_TYPE_EDGE_FALLING case, S5P_EXTINT_FALLEDGE is right
instead of S5P_EXTINT_RISEEDGE
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Hardware performance counters on ARM are 32-bits wide but atomic64_t
variables are used to represent counter data in the hw_perf_event structure.
The armpmu_event_update function right-shifts a signed 64-bit delta variable
and adds the result to the event count. This can lead to shifting in sign-bits
if the MSB of the 32-bit counter value is set. This results in perf output
such as:
Performance counter stats for 'sleep 20':
18446744073460670464 cycles <-- 0xFFFFFFFFF12A6000
7783773 instructions # 0.000 IPC
465 context-switches
161 page-faults
1172393 branches
20.154242147 seconds time elapsed
This patch ensures that the delta value is treated as unsigned so that the
right shift sets the upper bits to zero.
Cc: <stable@kernel.org>
Acked-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
RealView boards with certain revisions of the L210/L220 cache controller
may have issues (hardware deadlock) with the mandatory barriers (DSB
followed by an L2 cache sync) when ARM_DMA_MEM_BUFFERABLE is enabled.
The patch disables ARM_DMA_MEM_BUFFERABLE for these boards.
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
RealView boards with certain revisions of the L220 cache controller (ARM11*
processors only) may have issues (hardware deadlock) with the recent changes to
the mb() barrier implementation (DSB followed by an L2 cache sync). The patch
redefines the RealView ARM11MPCore mandatory barriers without the outer_sync()
call.
Cc: <stable@kernel.org>
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
