Each I/O APIC redirection table entry has a number of fields.
Define names for them to eliminate reference by hard coded
numbers.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If configured to use the I/O APIC, the NMI watchdog is deemed to fail if
the chip has been deactivated as a result of "noapic". Downgrade to the
local APIC watchdog similarly to what is done for the UP case.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A downgrade helper for the NMI watchdog to be used in all places where
the I/O APIC watchdog may have been requested, but the I/O APIC is found
not to be there or meant to be left disabled. This is so that the
reconfiguration is cosistent and defined in a single place only.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is no point in keeping the 8259A enabled if the I/O APIC NMI
watchdog has failed and the 8259A is not used to pass through regular
timer interrupts. This fixes problems with some systems where some logic
gets confused.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the "disable_8254_timer" and "enable_8254_timer" kernel
parameters. Now that AEOI acknowledgements are no longer needed for
correct timer operation, the 8259A can be kept disabled unconditionally
unless interrupts, either timer or watchdog ones, are actually passed
through it.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
1) Remove __meminit from update_pages_count. It is used inside
split_pages()
2) Make the code depend on PROC_FS. Doing statistics for nothing is
useless and not adding useless code is nice to the Linux tiny folks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add information about the mapping state of the direct mapping to
/proc/meminfo. I chose /proc/meminfo because that is where all the other
memory statistics are too and it is a generally useful metric even
outside debugging situations. A lot of split kernel pages means the
kernel will run slower.
This way we can see how many large pages are really used for it and how
many are split.
Useful for general insight into the kernel.
v2: Add hotplug locking to 64bit to plug a very obscure theoretical race.
32bit doesn't need it because it doesn't support hotadd for lowmem.
Fix some typos
v3: Rename dpages_cnt
Add CONFIG ifdef for count update as requested by tglx
Expand description
v4: Fix stupid bugs added in v3
Move update_page_count to pageattr.c
Signed-off-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
"Form follows function". Code is now where it belongs to.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
C1E on AMD machines is like C3 but without control from the OS. Up to
now we disabled the local apic timer for those machines as it stops
when the CPU goes into C1E. This excludes those machines from high
resolution timers / dynamic ticks, which hurts especially X2 based
laptops.
The current boot time C1E detection has another, more serious flaw
as well: some BIOSes do not enable C1E until the ACPI processor module
is loaded. This causes systems to stop working after that point.
To work nicely with C1E enabled machines we use a separate idle
function, which checks on idle entry whether C1E was enabled in the
Interrupt Pending Message MSR. This allows us to do timer broadcasting
for C1E and covers the late enablement of C1E as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Hypercalls can modify arbitrary regions of memory. Make sure to indicate this
in the clobber list. This fixes a hang when using KVM_GUEST kernel built with
GCC 4.3.0.
This was originally spotted and analyzed by Marcelo.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
These two macros are useful beyond lock debugging. Moved definitions from
include/linux/debug_locks.h to include/linux/kernel.h, so code that needs
them does not have to include the former, which would have been a less
intuitive choice of a header.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In linux-next there is a commit ("x86: Add performance variants of cpumask
operators") which, as part of the 4096 cpu support work adds some new APIs
for dealing with cpu masks. Add trivial versions of these now so that
subsystems can update in a timely manner and avoid conflicts in linux-next
and the next merge window.
Cc: Mike Travis <travis@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This has been sitting around unloved for way too long..
The Marvell CaFe chip's SD implementation chokes during card insertion
if one attempts to set the voltage and power up in the same
SDHCI_POWER_CONTROL register write. This adds a quirk that does
that particular dance in two steps.
It also adds an entry to pci_ids.h for the CaFe chip's SD device.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit includes a bugfix for the fragile setuid fixup code in the
case that filesystem capabilities are supported (in access()). The effect
of this fix is gated on filesystem capability support because changing
securebits is only supported when filesystem capabilities support is
configured.)
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andrew G. Morgan <morgan@kernel.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In linux-next there is a commit ("rcu: split list.h and move rcu-protected
lists into rculist.h") that moved the rcu related list iterators from
list.h to rculist.h. Add a trivial version of the file now so that
various subsystem trees can start using it now for -next changes and so
reduce the build errors caused by adding uses of the moved functions.
Cc: Franck Bui-Huu <fbuihuu@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
> the build (.config attached) failed, make ends with :
> ...
> UPD include/linux/compile.h
> CC init/version.o
> LD init/built-in.o
> LD vmlinux
> drivers/built-in.o: In function `sas_request_addr':
> (.text+0x33bab): undefined reference to `request_firmware'
> drivers/built-in.o: In function `sas_request_addr':
> (.text+0x33c3f): undefined reference to `release_firmware'
> make: *** [vmlinux] Error 1
There's a slight fault in the stub logic. It fails for FW_LOADER=m and
the user =y.
This should fix it.
This patch fixes the following 2.6.26-rc regression:
http://bugzilla.kernel.org/show_bug.cgi?id=10730
Reviewed-by: Toralf Foerster <toralf.foerster@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove all clameter@sgi.com addresses from the kernel tree since they will
become invalid on June 27th. Change my maintainer email address for the
slab allocators to cl@linux-foundation.org (which will be the new email
address for the future).
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slub: Do not use 192 byte sized cache if minimum alignment is 128 byte
The manual padding to align on cacheline size only worked in 32 bit
In 64 bit the structure was not aligned and contained wasted space.
use the compiler ____cachline_aligned to save space & properly align
this structure.
x86_64_default size goes from 9136 -> 8960
x86_64_AMD size goes from 9136 -> 8896
built & running on 2.6.26-rc8.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch changes the domain TLB flushing behavior of the driver. When there
is more than one page to flush it flushes the whole domain TLB instead of every
single page. So we send only a single command to the IOMMU in every case which
is faster to execute.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: iommu@lists.linux-foundation.org
Cc: bhavna.sarathy@amd.com
Cc: robert.richter@amd.com
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The branch optimization fixes in 2.6.21 introduced a bug in
atomic_sub_if_positive that causes it to return even when the sc
instruction fails. The result is that e.g. down_trylock becomes unreliable
as the semaphore counter is not always decremented.
Original MUA-shredded patch from Morten Larsen <mlarsen@broadcom.com>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 192 byte cache is not necessary if we have a basic alignment of 128
byte. If it would be used then the 192 would be aligned to the next 128 byte
boundary which would result in another 256 byte cache. Two 256 kmalloc caches
cause sysfs to complain about a duplicate entry.
MIPS needs 128 byte aligned kmalloc caches and spits out warnings on boot without
this patch.
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
* 'for-2.6.26' of git://git.kernel.dk/linux-2.6-block:
Properly notify block layer of sync writes
block: Fix the starving writes bug in the anticipatory IO scheduler
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Fix bad hint about irqs in i2c.h
i2c: Documentation: fix device matching description
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (55 commits)
net: fib_rules: fix error code for unsupported families
netdevice: Fix wrong string handle in kernel command line parsing
net: Tyop of sk_filter() comment
netlink: Unneeded local variable
net-sched: fix filter destruction in atm/hfsc qdisc destruction
net-sched: change tcf_destroy_chain() to clear start of filter list
ipv4: fix sysctl documentation of time related values
mac80211: don't accept WEP keys other than WEP40 and WEP104
hostap: fix sparse warnings
hostap: don't report useless WDS frames by default
textsearch: fix Boyer-Moore text search bug
netfilter: nf_conntrack_tcp: fixing to check the lower bound of valid ACK
ipv6 route: Convert rt6_device_match() to use RT6_LOOKUP_F_xxx flags.
netlabel: Fix a problem when dumping the default IPv6 static labels
net/inet_lro: remove setting skb->ip_summed when not LRO-able
inet fragments: fix race between inet_frag_find and inet_frag_secret_rebuild
CONNECTOR: add a proc entry to list connectors
netlink: Fix some doc comments in net/netlink/attr.c
tcp: /proc/net/tcp rto,ato values not scaled properly (v2)
include/linux/netdevice.h: don't export MAX_HEADER to userspace
...
Pass double tcf_proto pointers to tcf_destroy_chain() to make it
clear the start of the filter list for more consistency.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
i2c.h mentions -1 as a not-issued irq. This false hint was taken by
of_i2c and caused crashes. Don't give any advice as 'no irq' is not
consistent across all architectures yet and it is not needed internally
by the i2c-core.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
fsync_buffers_list() and sync_dirty_buffer() both issue async writes and
then immediately wait on them. Conceptually, that makes them sync writes
and we should treat them as such so that the IO schedulers can handle
them appropriately.
This patch fixes a write starvation issue that Lin Ming reported, where
xx is stuck for more than 2 minutes because of a large number of
synchronous IO in the system:
INFO: task kjournald:20558 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this
message.
kjournald D ffff810010820978 6712 20558 2
ffff81022ddb1d10 0000000000000046 ffff81022e7baa10 ffffffff803ba6f2
ffff81022ecd0000 ffff8101e6dc9160 ffff81022ecd0348 000000008048b6cb
0000000000000086 ffff81022c4e8d30 0000000000000000 ffffffff80247537
Call Trace:
[<ffffffff803ba6f2>] kobject_get+0x12/0x17
[<ffffffff80247537>] getnstimeofday+0x2f/0x83
[<ffffffff8029c1ac>] sync_buffer+0x0/0x3f
[<ffffffff8066d195>] io_schedule+0x5d/0x9f
[<ffffffff8029c1e7>] sync_buffer+0x3b/0x3f
[<ffffffff8066d3f0>] __wait_on_bit+0x40/0x6f
[<ffffffff8029c1ac>] sync_buffer+0x0/0x3f
[<ffffffff8066d48b>] out_of_line_wait_on_bit+0x6c/0x78
[<ffffffff80243909>] wake_bit_function+0x0/0x23
[<ffffffff8029e3ad>] sync_dirty_buffer+0x98/0xcb
[<ffffffff8030056b>] journal_commit_transaction+0x97d/0xcb6
[<ffffffff8023a676>] lock_timer_base+0x26/0x4b
[<ffffffff8030300a>] kjournald+0xc1/0x1fb
[<ffffffff802438db>] autoremove_wake_function+0x0/0x2e
[<ffffffff80302f49>] kjournald+0x0/0x1fb
[<ffffffff802437bb>] kthread+0x47/0x74
[<ffffffff8022de51>] schedule_tail+0x28/0x5d
[<ffffffff8020cac8>] child_rip+0xa/0x12
[<ffffffff80243774>] kthread+0x0/0x74
[<ffffffff8020cabe>] child_rip+0x0/0x12
Lin Ming confirms that this patch fixes the issue. I've run tests with
it for the past week and no ill effects have been observed, so I'm
proposing it for inclusion into 2.6.26.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch makes mac80211 refuse a WEP key whose length is not WEP40 nor
WEP104.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ptrace GET/SET FPXREGS broken
x86: fix cpu hotplug crash
x86: section/warning fixes
x86: shift bits the right way in native_read_tscp
This patch adds the Repeat key to the input layer. The usage
in the HUT is 0xBC (listed under "15.7 Transport Controls").
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (42 commits)
V4L/DVB (8108): Fix open/close race in saa7134
V4L/DVB (8100): V4L/vivi: fix possible memory leak in vivi_fillbuff
V4L/DVB (8097): xc5000: check device hardware state to determine if firmware download is needed
V4L/DVB (8096): au8522: prevent false-positive lock status
V4L/DVB (8092): videodev: simplify and fix standard enumeration
V4L/DVB (8075): stv0299: Uncorrected block count and bit error rate fixed
V4L/DVB (8074): av7110: OSD transfers should not be interrupted
V4L/DVB (8073): av7110: Catch another type of ARM crash
V4L/DVB (8071): tda10023: Fix possible kernel oops during initialisation
V4L/DVB (8069): cx18: Fix S-Video and Compsite inputs for the Yuan MPC718 and enable card entry
V4L/DVB (8068): cx18: Add I2C slave reset via GPIO upon initialization
V4L/DVB (8067): cx18: Fix firmware load for case when digital capture happens first
V4L/DVB (8066): cx18: Fix audio mux input definitions for HVR-1600 Line In 2 and FM radio
V4L/DVB (8063): cx18: Fix unintended auto configurations in cx18-av-core
V4L/DVB (8061): cx18: only select tuner / frontend modules if !DVB_FE_CUSTOMISE
V4L/DVB (8048): saa7134: Fix entries for Avermedia A16d and Avermedia E506
V4L/DVB (8044): au8522: tuning optimizations
V4L/DVB (8043): au0828: add support for additional USB device id's
V4L/DVB (8042): DVB-USB UMT-010 channel scan oops
V4L/DVB (8040): soc-camera: remove soc_camera_host_class class
...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
dock: bay: Don't call acpi_walk_namespace() when ACPI is disabled.
ACPI: don't walk tables if ACPI was disabled
thermal: Create CONFIG_THERMAL_HWMON=n
* 'audit.b52' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] remove useless argument type in audit_filter_user()
[PATCH] audit: fix kernel-doc parameter notation
[PATCH] kernel/audit.c: nlh->nlmsg_type is gotten more than once
When an SKB cannot be chained to a session, the current code attempts
to "restore" its ip_summed field from lro_mgr->ip_summed. However,
lro_mgr->ip_summed does not hold the original value; in fact, we'd
better not touch skb->ip_summed since it is not modified by the code
in the path leading to a failure to chain it. Also use a cleaer
comment to the describe the ip_summed field of struct net_lro_mgr.
Issue raised by Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the CONFIG_'s the value is anyway not correct in userspace.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to check for existence of the a.out.h header in the source tree,
not the object tree, if we want it to get the right answer with O=.
Signed-off-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
fix:
arch/x86/kernel/amd_iommu.c: In function ‘amd_iommu_init_dma_ops':
arch/x86/kernel/amd_iommu.c:940: error: lvalue required as left operand of assignment
arch/x86/kernel/amd_iommu.c:941: error: lvalue required as left operand of assignment
due to !CONFIG_GART_IOMMU.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
