Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a jump target so that a bit of exception handling can be better reused
at the end of this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a jump target so that a bit of exception handling can be better reused
at the end of this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Drivers in ALSA firewire stack still includes some symbols which can be
moved to a section for read-only symbols.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU Audio Express is one of third generation in MOTU FireWire
series, produced in 2011. This model consists of three chips:
* TI TSB41AB2 (Physical layer for IEEE 1394 bus)
* Microchip USB3300 (Hi-Speed USB Device with ULPI interface)
* Xilinx Spartan-3A FPGA, XC3S400A (Link layer for IEEE 1394 bus, packet
processing and data block processing layer)
This commit adds support for this model. As I expected, it works with
current implementaion of protocol version 3. On the other hand, the unit
has a quirk to request subaction originated by any driver.
11:45:51.287643 firewire_ohci 0000:03:00.0: AT spd 2 tl 1f, ffc1 -> ffc0, -reserved-, QW req, fffff0000b14 = 02000200
11:45:51.289193 firewire_ohci 0000:03:00.0: AR spd 2 tl 1f, ffc0 -> ffc1, ack_complete, W resp
11:45:51.289381 fireire_core 0000:03:00.0: unsolicited response (source ffc0, tlabel 1f)
11:45:51.313071 firewire_ohci 0000:03:00.0: AT spd 2 tl 20, ffc1 -> ffc0, ack_pending , QW req, fffff0000b14 = 02000200
11:45:51.314539 firewire_ohci 0000:03:00.0: AR spd 2 tl 20, ffc0 -> ffc1, ack_complete, W resp
In 1394 OHCI (rev.1.1), after OUTPUT_LAST* descriptors is processed,
'xferStaus' field is filled with 'ContextControl[0:15]' (see clause 7.1.3).
5 bits in LSB side of the field has ack code in acknowledge from the unit
(see clause 7.2.2). A list of the code is shown in Table 3-2.
As long as I investigated, in a case of the '-reserved-' acknowledge
message from the unit, the field has 0x10. On the table, this value is
'Reserved for definition by future 1394 standards'. As long as I know,
any specifications of IEEE 1394 has no such extensions, thus the unit is
out of specification. Besides, I note that the unit does not always
acknowledge with the invalid code. I guess this is a bug of firmware. I
confirmed the bug in firmware version 1.04 and this is the latest one.
$ cd linux-firewire-utils
$ python2 ./src/crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 0410a756 bus_info_length 4, crc_length 16, crc 42838
404 31333934 bus_name "1394"
408 20ff7000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 255, max_rec 7 (256)
40c 0001f200 company_id 0001f2 |
410 000a8a7b device_id 00000a8a7b | EUI-64 0001f200000a8a7b
root directory
-----------------------------------------------------------------
414 0004ef04 directory_length 4, crc 61188
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 d1000002 --> unit directory at 428
424 8d000005 --> eui-64 leaf at 438
unit directory at 428
-----------------------------------------------------------------
428 00031680 directory_length 3, crc 5760
42c 120001f2 specifier id
430 13000033 version
434 17104800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 00025ef3 leaf_length 2, crc 24307
43c 0001f200 company_id 0001f2 |
440 000a8a7b device_id 00000a8a7b | EUI-64 0001f200000a8a7b
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In protocols of MOTU FireWire series, when transferring MIDI messages,
transmitter set existence flag to one byte on first several quadlets. The
position differs depending on protocols and models, however two cases are
confirmed; in 5th byte and 8th byte from MSB side.
This commit adds a series of specification flag to describe them. When
the existence flag is in the 5th byte, SND_MOTU_SPEC_[R|T]X_MIDI_2ND_Q is
used. Else, another set of the flag is used. Here, '_Q' means quadlet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When calling 'iso_resource_free()' for uninitialized data, this function
causes NULL pointer dereference due to its 'unit' member. This occurs when
unplugging audio and music units on IEEE 1394 bus at failure of card
registration.
This commit fixes the bug. The bug exists since kernel v4.5.
Fixes: 324540c4e0 ('ALSA: fireface: postpone sound card registration') at v4.12
Fixes: 8865a31e0f ('ALSA: firewire-motu: postpone sound card registration') at v4.12
Fixes: b610386c8a ('ALSA: firewire-tascam: deleyed registration of sound card') at v4.7
Fixes: 86c8dd7f4d ('ALSA: firewire-digi00x: delayed registration of sound card') at v4.7
Fixes: 6c29230e2a ('ALSA: oxfw: delayed registration of sound card') at v4.7
Fixes: 7d3c1d5901 ('ALSA: fireworks: delayed registration of sound card') at v4.7
Fixes: 04a2c73c97 ('ALSA: bebob: delayed registration of sound card') at v4.7
Fixes: b59fb1900b ('ALSA: dice: postpone card registration') at v4.5
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_pcm_ops are not supposed to change at runtime. All functions
working with snd_pcm_ops provided by <sound/pcm.h> work with
const snd_pcm_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These snd_rawmidi_ops structures are only passed as the third
argument of snd_rawmidi_set_ops. This argument is const, so the
snd_rawmidi_ops structures can be const too.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At Linux v3.5, packet processing can be done in process context of ALSA
PCM application as well as software IRQ context for OHCI 1394. Below is
an example of the callgraph (some calls are omitted).
ioctl(2) with e.g. HWSYNC
(sound/core/pcm_native.c)
->snd_pcm_common_ioctl1()
->snd_pcm_hwsync()
->snd_pcm_stream_lock_irq
(sound/core/pcm_lib.c)
->snd_pcm_update_hw_ptr()
->snd_pcm_udpate_hw_ptr0()
->struct snd_pcm_ops.pointer()
(sound/firewire/*)
= Each handler on drivers in ALSA firewire stack
(sound/firewire/amdtp-stream.c)
->amdtp_stream_pcm_pointer()
(drivers/firewire/core-iso.c)
->fw_iso_context_flush_completions()
->struct fw_card_driver.flush_iso_completion()
(drivers/firewire/ohci.c)
= flush_iso_completions()
->struct fw_iso_context.callback.sc
(sound/firewire/amdtp-stream.c)
= in_stream_callback() or out_stream_callback()
->...
->snd_pcm_stream_unlock_irq
When packet queueing error occurs or detecting invalid packets in
'in_stream_callback()' or 'out_stream_callback()', 'snd_pcm_stop_xrun()'
is called on local CPU with disabled IRQ.
(sound/firewire/amdtp-stream.c)
in_stream_callback() or out_stream_callback()
->amdtp_stream_pcm_abort()
->snd_pcm_stop_xrun()
->snd_pcm_stream_lock_irqsave()
->snd_pcm_stop()
->snd_pcm_stream_unlock_irqrestore()
The process is stalled on the CPU due to attempt to acquire recursive lock.
[ 562.630853] INFO: rcu_sched detected stalls on CPUs/tasks:
[ 562.630861] 2-...: (1 GPs behind) idle=37d/140000000000000/0 softirq=38323/38323 fqs=7140
[ 562.630862] (detected by 3, t=15002 jiffies, g=21036, c=21035, q=5933)
[ 562.630866] Task dump for CPU 2:
[ 562.630867] alsa-source-OXF R running task 0 6619 1 0x00000008
[ 562.630870] Call Trace:
[ 562.630876] ? vt_console_print+0x79/0x3e0
[ 562.630880] ? msg_print_text+0x9d/0x100
[ 562.630883] ? up+0x32/0x50
[ 562.630885] ? irq_work_queue+0x8d/0xa0
[ 562.630886] ? console_unlock+0x2b6/0x4b0
[ 562.630888] ? vprintk_emit+0x312/0x4a0
[ 562.630892] ? dev_vprintk_emit+0xbf/0x230
[ 562.630895] ? do_sys_poll+0x37a/0x550
[ 562.630897] ? dev_printk_emit+0x4e/0x70
[ 562.630900] ? __dev_printk+0x3c/0x80
[ 562.630903] ? _raw_spin_lock+0x20/0x30
[ 562.630909] ? snd_pcm_stream_lock+0x31/0x50 [snd_pcm]
[ 562.630914] ? _snd_pcm_stream_lock_irqsave+0x2e/0x40 [snd_pcm]
[ 562.630918] ? snd_pcm_stop_xrun+0x16/0x70 [snd_pcm]
[ 562.630922] ? in_stream_callback+0x3e6/0x450 [snd_firewire_lib]
[ 562.630925] ? handle_ir_packet_per_buffer+0x8e/0x1a0 [firewire_ohci]
[ 562.630928] ? ohci_flush_iso_completions+0xa3/0x130 [firewire_ohci]
[ 562.630932] ? fw_iso_context_flush_completions+0x15/0x20 [firewire_core]
[ 562.630935] ? amdtp_stream_pcm_pointer+0x2d/0x40 [snd_firewire_lib]
[ 562.630938] ? pcm_capture_pointer+0x19/0x20 [snd_oxfw]
[ 562.630943] ? snd_pcm_update_hw_ptr0+0x47/0x3d0 [snd_pcm]
[ 562.630945] ? poll_select_copy_remaining+0x150/0x150
[ 562.630947] ? poll_select_copy_remaining+0x150/0x150
[ 562.630952] ? snd_pcm_update_hw_ptr+0x10/0x20 [snd_pcm]
[ 562.630956] ? snd_pcm_hwsync+0x45/0xb0 [snd_pcm]
[ 562.630960] ? snd_pcm_common_ioctl1+0x1ff/0xc90 [snd_pcm]
[ 562.630962] ? futex_wake+0x90/0x170
[ 562.630966] ? snd_pcm_capture_ioctl1+0x136/0x260 [snd_pcm]
[ 562.630970] ? snd_pcm_capture_ioctl+0x27/0x40 [snd_pcm]
[ 562.630972] ? do_vfs_ioctl+0xa3/0x610
[ 562.630974] ? vfs_read+0x11b/0x130
[ 562.630976] ? SyS_ioctl+0x79/0x90
[ 562.630978] ? entry_SYSCALL_64_fastpath+0x1e/0xad
This commit fixes the above bug. This assumes two cases:
1. Any error is detected in software IRQ context of OHCI 1394 context.
In this case, PCM substream should be aborted in packet handler. On the
other hand, it should not be done in any process context. TO distinguish
these two context, use 'in_interrupt()' macro.
2. Any error is detect in process context of ALSA PCM application.
In this case, PCM substream should not be aborted in packet handler
because PCM substream lock is acquired. The task to abort PCM substream
should be done in ALSA PCM core. For this purpose, SNDRV_PCM_POS_XRUN is
returned at 'struct snd_pcm_ops.pointer()'.
Suggested-by: Clemens Ladisch <clemens@ladisch.de>
Fixes: e9148dddc3c7("ALSA: firewire-lib: flush completed packets when reading PCM position")
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In ALSA firewire stack, 8 drivers uses IEC 61883-1/6 engine for data
transmission. They have common PCM info/constraints and duplicated codes.
This commit unifies the codes into fireiwre-lib.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA fireface driver has ALSA specific operations for MIDI/PCM data.
Structured data for the operations can be constified. Additionally,
The structured data can be function local.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In recent commit for ALSA PCM core, some arrangement is done for
'struct snd_pcm_ops.ack' callback. This is called when appl_ptr is
explicitly moved in intermediate buffer for PCM frames, except for
some cases described later.
For drivers in ALSA firewire stack, usage of this callback has a merit to
reduce latency between time of PCM frame queueing and handling actual
packets in recent isochronous cycle, because no need to wait for software
IRQ context from isochronous context of OHCI 1394.
If this works well in a case that mapped page frame is used for the
intermediate buffer, user process should execute some commands for ioctl(2)
to tell the number of handled PCM frames in the intermediate buffer just
after handling them. Therefore, at present, with a combination of below
conditions, this doesn't work as expected and user process should wait for
the software IRQ context as usual:
- when ALSA PCM core judges page frame mapping is available for status
data (struct snd_pcm_mmap_status) and control data
(struct snd_pcm_mmap_control).
- user process handles PCM frames by loop just with 'snd_pcm_mmap_begin()'
and 'snd_pcm_mmap_commit()'.
- user process uses PCM hw plugin in alsa-lib to operate I/O without
'sync_ptr_ioctl' option.
Unfortunately, major use case include these three conditions.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Declare snd_kcontrol_new structures as const as they are only passed an
argument to the function snd_ctl_new1. This argument is of type const,
so snd_kcontrol_new structures having this property can be made const.
Done using Coccinelle:
@r disable optional_qualifier@
identifier x;
position p;
@@
static struct snd_kcontrol_new x@p={...};
@ok@
identifier r.x;
position p;
@@
snd_ctl_new1(&x@p,...)
@bad@
position p != {r.p,ok.p};
identifier r.x;
@@
x@p
@depends on !bad disable optional_qualifier@
identifier r.x;
@@
+const
struct snd_kcontrol_new x;
Cross compiled these files:
sound/aoa/codecs/tas.c - powerpc
sound/mips/{hal2.c/sgio2audio.c} - mips
sound/ppc/{awacs.c/beep.c/tumbler.c} - powerpc
sound/soc/sh/siu_dai.c - sh
Could not find an architecture to compile sound/sh/aica.c.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, AM824 is described as format of data block. In this
format, one data block consists of several data channels, which is aligned
to 32 bit. One data channel has 8 bit label field and 24 bit data field.
PCM frames are transferred in Multi Bit Linear Audio (MBLA) data channel.
This channel can include 16/20/24 bit PCM sample.
As long as I know, models which support IEC 61883-1/6 doesn't allow to
switch bit length of PCM sample in MBLA data channel. They always
transmit/receive PCM frames of 24 bit length. This can be seen for the
other models which support protocols similar to IEC 61883-1/6.
On the other hand, current drivers for these protocols supports 16 bit
length PCM sample in playback substream. In this case, PCM sample is put
into the MBLA data channel with 8 bit padding in LSB side. Although 16
bit PCM sample is major because it's in CD format, this doesn't represent
device capability as is.
This commit removes support for 16 bit PCM samples in playback substream.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In development period for Linux v4.10, ktime_t became an alias of s64,
instead of union. I forgot it. We can just assign zero, instead of usage
of ktime_set(0, 0).
Fixes: 1917429578 ("ALSA: fireface: add transaction support")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Two functions were introduced for the purpose of tracing but cause warnings
when tracing is disabled:
sound/firewire/motu/amdtp-motu.c:284:13: error: 'copy_message' defined but not used [-Werror=unused-function]
static void copy_message(u64 *frames, __be32 *buffer, unsigned int data_blocks,
sound/firewire/motu/amdtp-motu.c:271:13: error: 'copy_sph' defined but not used [-Werror=unused-function]
static void copy_sph(u32 *frames, __be32 *buffer, unsigned int data_blocks,
Marking them as __maybe_unused will do the right thing here.
Fixes: 17909c1b30 ("ALSA: firewire-motu: add tracepoints for SPH in IEC 61883-1 fashion")
Fixes: c6b0b9e65f ("ALSA: firewire-motu: add tracepoints for messages for unique protocol")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA driver for TASCAM FireWire series transfers MIDI messages in system
workqueue. In current design of the driver, applications should wait for
sequence of transmission when they close ALSA rawmidi character devices.
However, when considering design of rawmidi interface, it's preferable
to wait in drain ioctl.
This commit adds support for the drain ioctl to wait for the end of
the transmission.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Units on TASCAM FireWire series handle MIDI messages with support for
running status. Drivers for the series should remember current running
status and transfer valid MIDI messages. For this purpose, current
ALSA driver for the series has some members in its top-level structure.
This is due to better abstraction of async midi port. Nowadays, the
abstraction was localized just for the driver.
This commit moves the members to structure for async midi port.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In current design of ALSA driver for TASCAM FireWire series, initialization
of members in asymc midi port structure is done at device probing. Some of
the members should be initialized every time to use rawmidi devices because
they're changed in sequence of transmission for MIDI messages.
This commit adds a new function to initialize them. Invariant parameters
during object lifetime are kept as is.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA driver for TASCAM FireWire series internally allocates 4 byte buffer
for asynchronous transaction to transfer MIDI messages. However, the buffer
can be allocated with memory object of parent structure.
This commit adds 4 byte array as a member of the structure and obsoletes
the redundant allocation. This is deallocated with memory object of parent
structure.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Units on TASCAM FireWire series receive MIDI messages by asynchronous
transactions on IEEE 1394 bus. Although the transaction is sent to a
certain register, current ALSA driver for this series has a redundant design.
This commit use the same address for the transaction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series uses asynchronous transactions with fixed length
payload for MIDI messaging. On the other hand, ALSA driver for the series
has a redundant design to handle different length of payload.
This commit removes the redundant abstraction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a result of localization of async midi port, ALSA driver for TASCAM
FireWire series can call helper function directly instead of callback
registration.
This commit removes the redundant design.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In Linux kernel 4.4, firewire-lib got a feature called as 'async midi port'
for transmission of MIDI message via IEEE 1394 asynchronous communication,
however actual consumer of this feature is ALSA driver for TASCAM FireWire
series only. When adding this feature, I assumed that ALSA driver for
Digi00x might also be a consumer, actually it's not.
This commit moves the feature from firewire-lib to firewire-tascam module.
Two minor kernel APIs are removed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
An abstraction of asynchronous transaction for transmission of MIDI
messages was introduced in Linux v4.4. Each driver can utilize this
abstraction to transfer MIDI messages via fixed-length payload of
transaction to a certain unit address. Filling payload of the transaction
is done by callback. In this callback, each driver can return negative
error code, however current implementation assigns the return value to
unsigned variable.
This commit changes type of the variable to fix the bug.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: <stable@vger.kernel.org> # 4.4+
Fixes: 585d7cba5e ("ALSA: firewire-lib: add helper functions for asynchronous transactions to transfer MIDI messages")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During packet streaming, maximum length of payload for isochronous packet
is invariable, therefore no need to recalculate. Current ALSA IEC 61883-1/6
engine calls a function to calculate it 8,000 or more times per second
for incoming packet processing.
This commit adds a member to have maximum length of payload into 'struct
amdtp_stream', to reduces the function calls. At first callback from
isochronous context, the length is calculated and stored for later
processing.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU units transfer/receive messages in each data block of their
isochronous packet payload. A part of content in the message is cleard for
MIDI message transmission, while the rest is unknown yet. Additional
features are required to assist users and developers to reveal the
details.
This commit adds tracepoints for the purpose. The tracepoints are designed
for MOTU's protocol version 2 and 3 (Protocol version 1 is not upstreamed
yet). In the tracepoints, events are probed to gather first two 24 bit
data chunks of each data block. The chunks are formatted into elements
of 64 bit array with padding in MSB.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unique protocol is used for MOTU FireWire series. In this protocol,
data block format is not compliant to AM824 in IEC 61883-1/6. Each of
the data block consists of 24 bit data chunks, except for a first
quadlet. The quadlet is used for source packet header (SPH) described
in IEC 61883-1.
The sequence of SPH seems to represent presentation timestamp
corresponding to included data. Developers have experienced that invalid
sequence brings disorder of units in the series.
Unfortunately, current implementation of ALSA IEC 61883-1/6 engine and
firewire-motu driver brings periodical noises to the units at sampling
transmission frequency based on 44.1 kHz. The engine generates the SPH with
even interval and this mechanism seems not to be suitable to the units.
Further work is required for this issue and infrastructure is preferable
to assist the work.
This commit adds tracepoints for the purpose. In the tracepoints, events
are probed to gather the SPHs from each data blocks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unique protocol is used for RME Fireface series. In this protocol,
payload format for isochronous packet is not compliant to CIP in
IEC 61883-1/6. The packet includes data blocks just with data channels,
without headers and any metadata.
In previous commits, ALSA IEC 61883-1/6 engine supports this protocol.
However, tracepoints are not supported yet, unlike implementation for
IEC 61883-1/6 protocol. This commit adds support of tracepoints for
the protocol.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In ALSA firewire stack, some AV/C commands are supported, including
vendor's extensions. Drivers includes response parser of each command,
according to its requirements, while the parser is written with loose
fashion in two points; error check and length check. This doesn't cause
any issues such as kernel corruption, but should be improved.
This commit modifies evaluations of return value on each parsers.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In protocol version 3, drivers can read current sampling clock status from
register 0x'ffff'f000'0b14. 8 bits of LSB of this register represents type
of signal as source of clock.
Current driver code includes invalid bitshift to handle the parameter. This
commit fixes the bug.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 5992e30034 ("ALSA: firewire-motu: add support for MOTU 828mk3 (FireWire/Hybrid) as a model with protocol version 3")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At a commit 6c29230e2a ("ALSA: oxfw: delayed registration of sound
card"), ALSA oxfw driver fails to handle SCS.1m/1d, due to -EBUSY at a call
of snd_card_register(). The cause is that the driver manages to register
two rawmidi instances with the same device number 0. This is a regression
introduced since kernel 4.7.
This commit fixes the regression, by fixing up device property after
discovering stream formats.
Fixes: 6c29230e2a ("ALSA: oxfw: delayed registration of sound card")
Cc: <stable@vger.kernel.org> # 4.7+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For digi00x series, asynchronous transaction is not used to transfer MIDI
messages to/from control surface. One of transction handlers in my previous
work loses its practical meaning.
This commit removes the handler. I note that unit of console type
transfers 0x00001000 to registered address of host space when switching
to 'standalone' mode. Then the unit generates bus reset.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At a commit c5fcee0373 ("ALSA: firewire-digi00x: add MIDI operations for
MIDI control port"), I described that MIDI messages for control surface is
transferred by a different way from the messages for physical ports.
However, this is wrong. MIDI messages to/from all of MIDI ports are
transferred by isochronous packets.
This commit removes codes to transfer MIDI messages via asynchronous
transaction, from MIDI handling layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At a commit 9dc5d31cdc ("ALSA: firewire-digi00x: handle MIDI messages in
isochronous packets"), a functionality to handle MIDI messages on
isochronous packet was supported. But this includes some of my
misunderstanding. This commit is to fix them.
For digi00x series, first data channel of data blocks in rx/tx packet
includes MIDI messages. The data channel has 0x80 in 8 bit of its MSB,
however it's against IEC 61883-6. Unique data format is applied:
- Upper 4 bits of LSB represent port number.
- 0x0: port 1.
- 0x2: port 2.
- 0xe: console port.
- Lower 4 bits of LSB represent the number of included MIDI message bytes;
0x0/0x1/0x2.
- Two bytes of middle of this data channel have MIDI bytes.
Especially, MIDI messages from/to console surface are also transferred by
isochronous packets, as well as physical MIDI ports.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Digi00x series includes two types of unit; rack and console. As long as
reading information on config rom of Digi 002 console, 'MODEL_ID' field
has a different value from the one on Digi 002 rack.
We've already got a test report from users with Digi 003 rack. We can
assume that console type and rack type has different value in the field.
This commit adds a device entry for console type. For following commits,
this commit also adds a member to 'struct snd_digi00x' to identify console
type.
$ cd linux-firewire-utils/src
$ python2 ./crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 0404f9d0 bus_info_length 4, crc_length 4, crc 63952
404 31333934 bus_name "1394"
408 60647002 irmc 0, cmc 1, isc 1, bmc 0, cyc_clk_acc 100, max_rec 7 (256)
40c 00a07e00 company_id 00a07e |
410 00a30000 device_id 0000a30000 | EUI-64 00a07e0000a30000
root directory
-----------------------------------------------------------------
414 00058a39 directory_length 5, crc 35385
418 0c0043a0 node capabilities
41c 04000001 hardware version
420 0300a07e vendor
424 81000007 --> descriptor leaf at 440
428 d1000001 --> unit directory at 42c
unit directory at 42c
-----------------------------------------------------------------
42c 00046674 directory_length 4, crc 26228
430 120000a3 specifier id
434 13000001 version
438 17000001 model
43c 81000007 --> descriptor leaf at 458
descriptor leaf at 440
-----------------------------------------------------------------
440 00055913 leaf_length 5, crc 22803
444 000050f2 descriptor_type 00, specifier_ID 50f2
448 80000000
44c 44696769
450 64657369
454 676e0000
descriptor leaf at 458
-----------------------------------------------------------------
458 0004a6fd leaf_length 4, crc 42749
45c 00000000 textual descriptor
460 00000000 minimal ASCII
464 44696769 "Digi"
468 20303032 " 002"
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface 400 is a second model of RME Fireface series, released in 2006.
This commit adds support for this model.
This model supports 8 analog channels, 2 S/PDIF channels and 8 ADAT
channels in both of tx/rx packet. The number of ADAT channels differs
depending on each mode of sampling transmission frequency.
$ python2 linux-firewire-utils/src/crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04107768 bus_info_length 4, crc_length 16, crc 30568 (should be 61311)
404 31333934 bus_name "1394"
408 20009002 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 9 (1024)
40c 000a3501 company_id 000a35 |
410 1bd0862a device_id 011bd0862a | EUI-64 000a35011bd0862a
root directory
-----------------------------------------------------------------
414 000485ec directory_length 4, crc 34284
418 03000a35 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 8d000006 --> eui-64 leaf at 438
424 d1000001 --> unit directory at 428
unit directory at 428
-----------------------------------------------------------------
428 000314c4 directory_length 3, crc 5316
42c 12000a35 specifier id
430 13000002 version
434 17101800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 000261a8 leaf_length 2, crc 25000
43c 000a3501 company_id 000a35 |
440 1bd0862a device_id 011bd0862a | EUI-64 000a35011bd0862a
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other drivers for audio and
music units on IEEE 1394 have.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds PCM functionality to transmit/receive PCM frames on
isochronous packet streaming. This commit enables userspace applications
to start/stop packet streaming via ALSA PCM interface.
Sampling rate requested by applications is used as sampling transmission
frequency of IEC 61883-1/6packet streaming. As I described in followed
commits, units in this series manages sampling clock frequency
independently of sampling transmission frequency, and they supports
resampling between their packet streaming/data block processing layer and
sampling data processing layer. This commit take this driver to utilize
these features for usability.
When internal clock is selected as source signal of sampling clock, this
driver allows user space applications to start PCM substreams at any rate
which packet streaming engine supports as sampling transmission frequency.
In this case, this driver expects units to perform resampling PCM frames
for rx/tx packets when sampling clock frequency and sampling transmission
frequency are mismatched. This is for daily use cases.
When any external clock is selected as the source signal, this driver
gets configured sampling rate from units, then restricts available
sampling rate to the rate for PCM applications. This is for studio use
cases.
Models in this series supports 64.0/128.0 kHz of sampling rate, however
these frequencies are not supported by IEC 61883-6 as sampling transmission
frequency. Therefore, packet streaming engine of ALSA firewire stack can't
handle them. When units are configured to use any external clock as source
signal of sampling clock and one of these unsupported rate is configured
as rate of the sampling clock, this driver returns EIO to user space
applications.
Anyway, this driver doesn't voluntarily configure parameters of sampling
clock. It's better for users to work with appropriate user space
implementations to configure the parameters in advance of usage.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds management functionality for packet streaming.
As long as investigating Fireface 400, there're three modes depending
on sampling transmission frequency. The number of data channels in each
data block is different depending on the mode. The set of available
data channels for each mode might be different for each protocol and
model.
The length of registers for the number of isochronous channel is just
three bits, therefore 0-7ch are available.
When bus reset occurs on IEEE 1394 bus, the device discontinues to
transmit packets. This commit aborts PCM substreams at bus reset handler.
As I described in followed commits, The device manages its sampling clock
independently of sampling transmission frequency against IEC 61883-6.
Thus, it's a lower cost to change the sampling transmission frequency,
while data fetch between streaming layer and DSP require larger buffer
for resampling. As a result, device latency might tend to be larger than
ASICs for IEC 61883-1/6 such as DM1000/DM1100/DM1500 (BeBoB),
DiceII/TCD2210/TCD2220/TCD3070 and OXFW970/971.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating Fireface 400, format of payload of each
isochronous packet is not IEC 61883-1/6, thus its format of data block
is not AM824. The remarkable points of the format are:
* The payload just consists of some data channels of quadlet size without
CIP header.
* Each data channels includes data aligned to little endian order.
* One data channel consists of two parts; 8 bit ancillary field and 24 bit
PCM frame.
Due to lack of CIP headers, rx/tx packets include no CIP headers and
different way to check packet discontinuity. For tx packet, the ancillary
field is used for counter. However, the way of counting is different
depending on positions of data channels. At 44.1 kHz, ancillary field in:
* 1st/6th/9th/10th/14th/17th data channels: not used for this purpose.
* 2nd/18th data channels: incremented every data block (0x00-0xff).
* 3rd/4th/5th/11th/12th/13th data channels: incremented every 256 data
blocks (0x00-0x07).
* 7th/8th/15th/16th data channels: incremented per the number of data
blocks in a packet. The increment can occur per packet (0x00-0xff).
For tx packet, tag of each isochronous packet is used for this purpose.
The value of tag cyclically changes between 0, 1, 2 and 3 in this order.
The interval is different depending on sampling transmission frequency.
At 44.1/48.0 kHz, it's 256 data blocks. At 88.2 kHz, it's 96 data blocks.
The number of data blocks in tx packet is exactly the same as
SYT_INTERVAL. There's no empty packet or no-data packet, thus the
throughput is not 8,000 packets per sec. On the other hand, the one in
rx packet is 8,000 packets per sec, thus the number of data blocks is
different between each packet, depending on sampling transmission
frequency:
* 44.1 kHz: 5 or 6
* 48.0 kHz: 5 or 6 or 7
* 88.2 kHz: 10 or 11 or 12
This commit adds data processing layer to satisfy the above specification
in a policy of 'best effort'. Although PCM frames are handled for
intermediate buffer to user space, the ancillary data is not handled at all
to reduce CPU usage, thus counter is not checked. 0 is always used for tag
of isochronous packet. Furthermore, the packet streaming layer is
responsible for calculation of the number of data blocks for each packet,
thus it's not exactly the same sequence from the above observation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating Fireface 400, IEC 61883-1/6 is not applied to
its packet streaming protocol. Remarks of the specific protocol are:
* Each packet doesn't include CIP headers.
* 64,0 and 128,0 kHz are supported.
* The device doesn't necessarily transmit 8,000 packets per second.
* 0, 1, 2, 3 are used as tag for rx isochronous packets, however 0 is
used for tx isochronous packets.
On the other hand, there's a common feature. The number of data blocks
transferred in a second is the same as sampling transmission frequency.
Current ALSA IEC 61883-1/6 engine already has a method to calculate it and
this driver can utilize it for rx packets, as well as tx packets.
This commit adds support for the transferring protocol. CIP_NO_HEADERS
flag is newly added. When this flag is set:
* Both of 0 (without CIP header) and 1 (with CIP header) are used as tag
to handle incoming isochronous packet.
* 0 (without CIP header) is used as tag to transfer outgoing isochronous
packet.
* Skip CIP header evaluation.
* Use unique way to calculate the quadlets of isochronous packet payload.
In ALSA PCM interface, 128.0 kHz is not supported, and the ALSA
IEC 61883-1/6 engine doesn't support 64.0 kHz. These modes are dropped.
The sequence of rx packet has a remarkable quirk about tag. This will be
described in later commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Audio and music units of RME Fireface series use its own protocol for
isochronous packets to transfer data. This protocol requires ALSA IEC
61883-1/6 engine to have alternative functions.
This commit is a preparation for the protocol.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Drivers can retrieve the state and configuration of clock by read
transactions.
This commit allows protocol abstraction layer to to dump the
information for debugging, via proc interface.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commit, fireface driver supports unique transaction mechanism
for MIDI feature. This commit adds MIDI functionality for userspace
applications.
As I wrote in a followed commit, user space applications get some
requirement from this driver. It should not touch a register to which
units transmit MIDI messages. It should configure a register in which
MIDI transmission is controlled.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating Fireface 400, MIDI messages are transferred by
asynchronous communication over IEEE 1394 bus.
Fireface 400 receives MIDI messages by write transactions to two addresses;
0x'0000'0801'8000 and 0x'0000'0801'9000. Each of two seems to correspond to
MIDI port 1 and 2.
Fireface 400 transfers MIDI messages by write transactions to certain
addresses which configured by drivers. The drivers can decide upper 4 byte
of the addresses by write transactions to 0x'0000'0801'03f4. For the rest
part of the address, drivers can select from below options:
* 0x'0000'0000
* 0x'0000'0080
* 0x'0000'0100
* 0x'0000'0180
Selected options are represented in register 0x'0000'0801'051c as bit
flags. Due to this mechanism, drivers are restricted to use addresses on
'Memory space' of IEEE 1222, even if transactions to the address have
some side effects.
This commit adds transaction support for MIDI messaging, based on my
assumption that the similar mechanism is used on the other protocols. To
receive asynchronous transactions, the driver allocates a range of address
in 'Memory space'. I apply a strategy to use 0x'0000'0000 as lower 4 byte
of the address. When getting failure from Linux FireWire subsystem, this
driver retries to allocate addresses.
Unfortunately, read transaction to address 0x'0000'0801'051c returns zero
always, however write transactions have effects to the other features such
as status of sampling clock. For this reason, this commit delegates a task
to configure this register to user space applications. The applications
should set 3rd bit in LSB in little endian order.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As of 2016, RME discontinued its Fireface series, thus it's OK for us
to focus on released firmwares to drive known units.
As long as investigating Fireface 400 with Windows driver and comparing
the result to FFADO implementation, I can see these firmwares have
different register assignments. On the other hand, according to manuals
of each models, features relevant to packet streaming seem to be common,
because GUIs for these models have the same options. It's reasonable to
assume an abstraction layer of protocols to communicate to each models.
This commit adds the abstraction layer for the protocols. This layer
includes some functions to operate common features of models in this
series.
In IEC 61883-1/6, the sequence of packet can transfer timing information
to synchronize receivers to transmitters. Units of each node on IEEE 1394
bus can generate transmitter's timing clock by handling value of SYT field
in CIP header with high-precision clock. For audio and music units on
IEEE 1394 bus, this recovered clock is designed to used for sampling clock
to capture/generate PCM frames on DSP/ADC/DAC. (Actually, in this world,
there's no units to implement this specification as is, as long as I
know).
Fireface series doesn't use this mechanism. Besides, It doesn't use
isochronous packet with CIP header. It uses internal crystal unit as its
initial sampling clock. When detecting input signals which can be
available for sampling clock (e.g. ADAT input), drivers can configure
units to use the signals as source of sampling clock. When something goes
wrong, e.g. frequency mismatching between the signal and configured value,
units fallback to the other detected signals alternatively. When detecting
no alternatives, internal crystal unit is used as source of sampling
clock. On manual of Fireface 400, this mechanism is described as
'Autosync'.
On the units, packet streaming is controlled by write transactions to
certain registers. Format of the packet, e.g. the number of data channels
in a data block, is also configured by the same manner. For this purpose,
.begin_session and .finish_session is added.
The remarkable point of this protocol is to allow drivers to configure
arbitrary sampling transmission frequency; e.g. 12.345 Hz. As long as I
know, there's no actual DAC/ADC chips which support this kind of
capability. I think a pair of packet streaming layer and data block
processing layer is isolated from sampling data processing layer in a
point of governed clock. In short, between these parts, resampling layer
exists. Actually, for Fireface 400, write transactions to
0x'0000'8010'051c has an effect to change sampling clock frequency with
base frequencies (32.0/44.1/48.0 kHz) and its multipliers (x2/x4),
regardless of sampling transmission frequency.
For this reason, the abstraction layer doesn't handle parameters for
sampling clock. Instead, each implementation of .begin_session is
expected to configure sampling transmission frequency.
For packet streaming layer, it's enough to get current selection of
source signals for the sampling clock and its frequency. In the
abstraction layer, when internal crystal is selected, drivers can sets
arbitrary sampling frequency, else they should follow configured
frequency. For this purpose, .get_clock is added.
Drivers are allows to bank up data fetching from a pair of packet
streaming/data block processing layer and sampling data processing layer.
This feature seems to suppress noises at starting/stopping packet
streaming. For this purpose, .switch_fetching_mode is added.
As I described in the above, units have remarkable mechanism to manage
sampling clock and process sampling data. For debugging purpose,
.dump_sync_status and .dump_clock_config are added. I don't have a need
to common interface to represent the status and configuration,
developers can add actual implementation of the abstraction layer as they
like.
Unlike PCM frames, MIDI messages are transferred by asynchronous
communication over IEEE 1394 bus, thus target addresses are important for
this feature. The .midi_high_addr_reg, .midi_rx_port_0_reg and
.midi_rx_port_1_reg are for this purpose. I'll describe them in following
commit.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
RME Fireface series has several models and their specifications are
different. Currently, we find no way to retrieve the specifications
from actual devices and need to implement them in this driver.
This commit adds a structure to describe model specific data. This
structure has an identical name for each unit, and maximum number of
data channels in each mode. I'll describe about the mode in following
commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just after appearing on IEEE 1394 bus, this unit generates several bus
resets. This is due to loading firmware from on-board flash memory and
initialize hardware. It's better to postpone sound card registration.
This commit schedules workqueue to process actual probe processing
2 seconds after the last bus-reset. The card instance is kept at unit
probe callback and released at card free callback. Therefore, when the
actual probe processing fails, the memory block is wasted. This is due to
simplify driver implementation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for RME Fireface series. This commit just
creates/removes card instance according to IEEE 1394 bus event. More
functions will be added in following commits.
Three types of firmware have released by RME GmbH; for Fireface 400, for
Fireface 800 and for UCX/802/UFX. It's reasonable that these models use
different protocol for communication. Currently, I've investigated
Fireface 400 and nothing others.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU 828mk3 (FireWire/Hybrid) is one of third generation in MOTU FireWire
series, produced in 2008/2014. This model consists of three chips for
functionality on IEEE 1394 bus:
* TI TSB41AB2 (Physical layer for IEEE 1394 bus)
* Xilinx Spartan-3E FPGA Family (Link layer for IEEE 1394 bus, packet
processing and data block processing layer)
* TI TMS320C6722 (Digital signal processing)
This commit adds a support for this model, with its unique protocol as
version 3. This protocol has some additional features to protocol
version 2.
* Support several optical interfaces.
* Support a data chunk for return of reverb effect.
* Have a quirk of tx packets.
* Support heartbeat asynchronous transaction.
In this protocol, series of transferred packets has some quirks. Below
fields in CIP headers of the packets are out of IEC 61883-1:
- SID (source node id): always 0x0d
- DBS (data block size): always 0x04
- DBC (data block counter): always 0x00
- EOH (End of header): always 0x00
Below is an actual sample of transferred packets.
quads CIP1 CIP2
520 0x0D040400 0x22FFFFFF
8 0x0D040400 0x22FFFFFF
520 0x0D040400 0x22FFFFFF
520 0x0D040400 0x22FFFFFF
8 0x0D040400 0x22FFFFFF
Status of clock is configured by write transactions to 0x'ffff'f000'0b14,
as well as version 2, while meanings of fields are different from the
former protocols. Modes of optical interfaces are configured by write
transactions to 0x'ffff'f000'0c94.
Drivers can register its address to receive heatbeat transactions from the
unit. 0x'ffff'f000'0b0c is for the higher part and 0x'ffff'f000'0b10 is
for the lower part. Nevertheless, this feature is not useless for this
driver and this commit omits it.
Each data block consists of two parts in a point of the number of included
data chunks. In both of 'fixed' and 'differed' parts, the number of
included data blocks are a multiple of 4, thus depending on models there's
some empty data chunks. For example, 828mk3 includes one pair of empty
data chunks in its fixed part. When optical interface is configured to
S/PDIF, 828mk3 includes one pair of empty data chunks in its differed part.
To reduce consumption of CPU cycles with additional conditions/loops, this
commit just exposes these empty chunks to user space as PCM channels.
Additionally, 828mk3 has a non-negligible overhead to change its sampling
transfer frequency. When softwares send asynchronous transaction to
perform it, LED on the unit starts to blink. In a worst case, it continues
blink during several seconds; e.g. 10 seconds. When stopping blinking,
the unit seems to be prepared for the requested sampling transfer
frequency. To wait for the preparation, this commit forces the driver
to call task scheduler and applications sleeps for 4 seconds.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-1, when two quadlets CIP header is used, the most significant
bit in second CIP header stands. However, packets from units with MOTU
protocol version 3 have a quirk without this flag. Current packet streaming
layer handles this as protocol error.
This commit adds a new enumeration constant for this quirk, to handle MOTU
protocol version 3.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU 828mk2 is one of second generation in MOTU FireWire series, produced in
2003. This model consists of four chips:
* TI TSB41AB2 (Physical layer for IEEE 1394 bus)
* PDI 1394L40BE (Link layer for IEEE 1394 bus and packet processing layer)
* ALTERA ACEX 1K EP1K30 Series FPGA (Data block processing layer)
* TI TMS320VC5402 (Digital signal processing)
This commit adds a support for this model, with its unique protocol as
version 2. The features of this protocol are:
* Support data chunks for status and control messages for both
directions.
* Support a pair of MIDI input/output.
* Support a data chunk for mic/instrument independent of analog line in.
* Support a data chunk for playback return.
* Support independent data chunks for S/PDIF of both optical/coaxial
interfaces.
* Support independent data chunks for each of main out and phone out.
Status of clock is configured by write transactions to 0x'ffff'f000'0b14.
Modes of optical interfaces are configured by write transactions to
0x'ffff'f000'0c04.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU FireWire series can transfer messages to registered address. These
messages are transferred for the status of internal clock synchronization
just after starting streams.
When the synchronization is stable, it's 0x01ffffff. Else, it's 0x05ffffff.
This commit adds a functionality for user space applications to receive
content of the message.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other sound drivers for units
on IEEE 1394 bus have.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In MOTU FireWire series, MIDI messages are multiplexed to isochronous
packets as well as PCM frames, while the way is different from the one
in IEC 61883-6.
MIDI messages are put into a certain position in message chunks. One data
block can includes one byte of the MIDI messages. When data block includes
a MIDI byte, the block has a flag in a certain position of the message
chunk. These positions are unique depending on protocols.
Once a data block includes a MIDI byte, some following data blocks includes
no MIDI bytes. Next MIDI byte appears on a data block corresponding to
next cycle of physical MIDI bus. This seems to avoid buffer overflow caused
by bandwidth differences between IEEE 1394 bus and physical MIDI bus.
This commit adds MIDI functionality to transfer/receive MIDI messages.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds PCM functionality to transmit/receive PCM samples.
When one of PCM substreams are running or external clock source is
selected, current sampling rate is used. Else, the sampling rate is
changed according to requests from a userspace application.
Available number of samples in a frame of PCM substream is determined at
open(2) to corresponding PCM character device. Later, packet streaming
starts by ioctl(2) with SNDRV_PCM_IOCTL_PREPARE. In theory, between them,
applications can change state of the unit by any write transaction to
change the number. In this case, this driver may fail packet streaming due
to wrong data format.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a functionality to manage packet streaming for MOTU
FireWire series.
The streaming is not controlled by CMP, thus against IEC 61883-1. Write
transaction to certain addresses start/stop packet streaming.
Transactions to 0x'ffff'f000'0b00 results in isochronous channel number for
both directions and starting/stopping transmission of packets. The
isochronous channel number is represented in 6 bit field, thus units can
identify the channels up to 64, as IEEE 1394 bus specification described.
Transactions to 0x'ffff'f000'0b10 results in packet format for both
directions and transmission speed. When each of data block includes fixed
part of data chunks only, corresponding flags stand.
When bus reset occurs, the units continue to transmit packets with
non-contiguous data block counter. This causes discontinuity detection in
packet streaming engine and ALSA PCM applications receives EPIPE from any
I/O operation. In this case, typical applications manage to recover
corresponding PCM substream. This behaviour is kicked much earlier than
callback of bus reset handler by Linux FireWire subsystem, therefore
status of packet streaming is not changed in the handler.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All models of MOTU FireWire series can be controlled by write transaction
to addresses in a range from 0x'ffff'f0000'0b00 to 0x'ffff'f000'0cff.
The models support asynchronous notification. This notification has 32 bit
field data, and is transferred when status of clock changes. Meaning of
the value is not enough clear yet.
Drivers can register its address to receive the notification. Write
transaction to 0x'ffff'f000'0b04 registers higher 16 bits of the address.
Write transaction to 0x'ffff'f0000'0b08 registers the rest of bits. The
address includes node ID, thus it should be registered every time of bus
reset.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU FireWire series uses blocking transmission for AMDTP packet streaming.
They transmit/receive 8,000 packets per second, to handle the same number
of data blocks as current sampling transmission frequency. Thus,
IEC 61883-1/6 packet streaming engine of ALSA firewire stack is available
for them.
However, the sequence of packet and data blocks includes some quirks.
Below sample is a sequence of CIP headers of packets received by 828mk2,
at 44.1kHz of sampling transmission frequency.
quads CIP1 CIP2
488 0x020F04E8 0x8222FFFF
8 0x020F04F8 0x8222FFFF
488 0x020F0400 0x8222FFFF
488 0x020F0408 0x8222FFFF
8 0x020F04E8 0x8222FFFF
488 0x020F04F0 0x8222FFFF
488 0x020F04F8 0x8222FFFF
The SID (source node ID), DBS (data block size), SPH (source packet header),
FMT (format ID), FDF (format dependent field) and SYT (time stamp) fields
are in IEC 61883-1. Especially, FMT is 0x02, FDF is 0x22 and SYT is 0xffff
to define MOTU specific protocol. In an aspect of dbc field, the value
represents accumulated number of data blocks included the packet. This
is against IEC 61883-1, because according to the specification this value
should be the number of data blocks already transferred.
In ALSA IEC 61883-1/6 engine, this quirk is already supported by
CIP_DBC_IS_END_EVENT flag, because Echo Audio Fireworks has.
Each data block includes SPH as its first quadlet field, to represent its
presentation time stamp. Actual value of SPH is compliant to IEC 61883-1;
lower 25 bits of 32 bits width consists of 13 bits cycle count and 12 bits
cycle offset.
The rest of each data block consists of 24 bit chunks. All of PCM samples,
MIDI messages, status and control messages are transferred by the chunks.
This is similar to '24-bit * 4 Audio Pack' in IEC 61883-6. The position of
each kind of data depends on generations of each model. The number of
whole chunks in a data block is a multiple of 4, to consists of
quadlet-aligned packets.
This commit adds data block processing layer specific for the MOTU
protocol. The remarkable point is the way to generate SPH header. Time
stamps for each data blocks are generated by below calculation:
* Using pre-computed table for the number of ticks per event
* 44,1kHz: (557 + 123/441)
* 48.0kHz: (512 + 0/441)
* 88.2kHz: (278 + 282/441)
* 96.0kHz: (256 + 0/441)
* 176.4kHz: (139 + 141/441)
* 192.0kHz: (128 + 0/441)
* Accumulate the ticks and set the value to SPH for every events.
* This way makes sense only for blocking transmission because this mode
transfers fixed number or none of events.
This calculation assumes that each data block has a PCM frame which is
sampled according to event timing clock. Current packet streaming layer
has the same assumption.
Although this sequence works fine for MOTU FireWire series at sampling
transmission frequency based on 48.0kHz, it is not enough at the frequency
based on 44.1kHz. The units generate choppy noise every few seconds.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit c8bdf49b9935("ALSA: fireworks/firewire-lib: Add a quirk for the
meaning of dbc") adds CIP_DBC_IS_END_EVENT flag just for tx packets.
However, MOTU FireWire series has this quirk for rx packets.
This commit allows both directions with the flag.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-1, CIP headers can have a SPH field. When a packet has 1 in
SPH field of its CIP header, the packet has a source packet headers. A
source packet header consists of 32 bit field (= 1 quadlet) and it
transfers time stamp, which is the same value as the lower 25 bits of the
IEEE 1394 CYCLE_TIMER register and the rest is zero.
This commit just supports source packet header field because IEC 61883-1
includes ambiguity the position of this header and its count. Each
protocol layer is allowed to have actual implementation according its
requirements.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, packet streaming layer passes generated SYT value to data block
processing layer. However, this is not enough in a case that the data block
processing layer generates time stamps by its own ways.
For out-packet stream, the packet streaming layer guarantees 8,000 times
calls of data block processing layers per sec. Therefore, when cycle count
of the first packet is recorded, data block processing layers can calculate
own time stamps with the recorded value.
For the reason, this commit allows packet streaming layer to record the
first cycle count. Each data block processing layer can read the count by
accessing a member of structure for packet streaming layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In an aspect of used protocols to communicate, models of MOTU FireWire
units are categorized to three generations.
This commit adds an abstraction layer of the protocols for features
related to packet streaming functionality. This layer includes 5
operations.
When configuring packet streaming functionality with sampling rate and
sampling transmission frequency, .get_clock_rate and .set_clock_rate are
called with proper arguments. MOTU FireWire series supports up to 192.0kHz.
When checking current source of sampling clock (not clock for packetization
layer), .get_clock_source is used. Enumeration is added to represent the
sources supported by this series. This operation can be used to expose
available sampling rate to user space applications when the unit is
configured to use any input signal as source of clock instead of crystal
clock.
In the protocols, the path between packet processing layer and digital
signal processing layer can be controlled. This looks a functionality to
'mute' the unit. For this feature, .switch_fetching_mode is added. This
can be used to suppress noises every time packet streaming starts/stops.
In a point of the size of data blocks at a certain sampling transmission
frequency, the most units accept several modes. This is due to usage of
optical interfaces. The size differs depending on which modes are
configured to the interfaces; None, S/PDIF and ADAT. Additionally, format
of packet is different depending on protocols. To cache current size of
data blocks and its format, .cache_packet_formats is added. This is used
by PCM functionality, packet streaming functionality and data block
processing layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU FireWire series doesn't tell drivers their capabilities, thus
the drivers should have and apply model-dependent parameters to detected
models.
This commit adds a structure to represent such parameters. Capabilities
are represented by enumeration except for the number of analog line
in/out. Identification name also be in the structure because the units has
no registers for this purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just after appearing on IEEE 1394 bus, this unit generates several bus
resets. This is due to loading firmware from on-board flash memory and
initialize hardware. It's better to postpone sound card registration.
This commit applies this idea.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds an new driver for MOTU FireWire series. In this commit,
this driver just creates/removes card instance according to bus event.
More functionalities will be added in following commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now snd_rawmidi_ops is maintained as a const pointer in snd_rawmidi,
we can constify the definitions.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 6b7e95d133. This commit
is based on a concern about value of the given parameter. It's expected
to be ORed value with some enumeration-constants, thus often it can not be
one of the enumeration-constants. I understood that this is out of
specification and causes implementation-dependent issues.
In C language specification, enumerated type can be interpreted as an
integer type, in which all of enumeration-constants in corresponding
enumerator-list can be stored. Implementations can select one of char,
signed int and unsigned int as its type, and this selection is
implementation-dependent.
In GCC, a signed integer is selected when at least one of
enumeration-constants has negative value, else an unsigned integer is
selected. This behaviour can be switched by -fshort-enums to short type.
Anyway, the type can be decided after scanning all of
enumeration-constants.
Totally, there's no rules to constrain the value of enumerated type to
be one of enumeration-constants. In short, in enumerated type, decision
of actual type for the type is the most important and
enumeration-constants are just used for the decision, thus it's permitted
to have an integer value in a range of enumeration-constants. In our case,
actual type for the type is currently deterministic to be either char or
unsigned int. Under GCC, it's unsigned int.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As of kernel 4.10, ALSA dice driver is expected to be used in default
speed. In most cases, it's S400. While, IEEE 1394 specification describes
the other speed such as S800.
According to 'TCD30XX User Guide', its link layer controller supports
several transmission speed up to S800[0]. In Dice software interface,
transmission speed in output direction can be configured by asynchronous
transaction to 'TX_SPEED' offset in its address space. S800 may be
available.
This commit improves configuration of transmission unit before starting
packet streaming for this purpose. The value of 'max_speed' in 'fw_device'
data structure has available maximum speed decided in bus arbitration,
thus it's within capacity of the unit.
[0] TCD3xx User Guide - TCAT 1394 LLC, Revision 0.9.0-41360 (TC Applied Technologies, May 6 2015)
http://www.tctechnologies.tc/index.php/support/support-hardware/dice-iii-detailed-documentation
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 'amdtp_stream' structure is initialized by a call of
'amdtp_stream_init()'. Although a parameter of this function is for bit
flags of packet attributes, its type is enumerator.
This commit changes the type so that it's proper for a bit flags.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This module has a bug not to return error code in a case that data
structure for transmitted packets fails to be initialized.
This commit fixes the bug.
Fixes: 35efa5c489 ("ALSA: firewire-tascam: add streaming functionality")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA fireworks driver has a bug not to call an API to destroy
'cmp_connection' structure for input direction. Currently this causes no
issues because it just destroys 'mutex' structure, while it's better to
fix it for future work.
Fix: d23c2cc448 ("ALSA: fireworks/bebob/dice/oxfw: allow stream destructor after releasing runtime")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Check for snd_pcm_ops structures that are only stored in the ops field of a
snd_soc_platform_driver structure or passed as the third argument to
snd_pcm_set_ops. The corresponding field or parameter is declared const,
so snd_pcm_ops structures that have this property can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_pcm_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_platform_driver e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i;
expression e1, e2;
position p;
@@
snd_pcm_set_ops(e1, e2, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_pcm_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_pcm_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In hwdep interface of fireworks driver, accessing to user space is in a
critical section with disabled local interrupt. Depending on architecture,
accessing to user space can cause page fault exception. Then local
processor stores machine status and handles the synchronous event. A
handler corresponding to the event can call task scheduler to wait for
preparing pages. In a case of usage of single core processor, the state to
disable local interrupt is worse because it don't handle usual interrupts
from hardware.
This commit fixes this bug, performing the accessing outside spinlock. This
commit also gives up counting the number of queued response messages to
simplify ring-buffer management.
Reported-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Cc: stable@vger.kernel.org
Fixes: 555e8a8f7f14('ALSA: fireworks: Add command/response functionality into hwdep interface')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In hwdep interface of firewire-tascam driver, accessing to user space is
in a critical section with disabled local interrupt. Depending on
architecture, accessing to user space can cause page fault exception. Then
local processor stores machine status and handle the synchronous event. A
handler corresponding to the event can call task scheduler to wait for
preparing pages. In a case of usage of single core processor, the state to
disable local interrupt is worse because it doesn't handle usual interrupts
from hardware.
This commit fixes this bug, by performing the accessing outside spinlock.
Reported-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Cc: stable@vger.kernel.org
Fixes: e5e0c3dd257b('ALSA: firewire-tascam: add hwdep interface')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The below models were developed with a cooperation by Yamaha and Terratec.
- Yamaha GO 44/Terratec PHASE 24 FW
- Yamaha GO 46/Terratec PHASE X24 FW
They have the same configurations, thus it's better to unify corresponding
codes.
This commit merges them to reduce the amount of maintained codes.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Once Yamaha and Terratec cooperated to develop some audio and music units
on IEEE 1394 bus. On these models, the same embedded board is used, and
similar configurations are also applied.
This commit renames file for Yamaha's configuration so that it's for both
of Yamaha and Terratec.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
