I stumbled over an old OSA model that claims to support DIAG_ASSIST,
but then rejects the cmd to query its DIAG capabilities.
In the old code this was ok, as the returned raw error code was > 0.
Now that we translate the raw codes to errnos, the "rc < 0" causes us
to fail the initialization of the device.
The fix is trivial: don't bail out when the DIAG query fails. Such an
error is not critical, we can still use the device (with a slightly
reduced set of features).
Fixes: 742d4d4083 ("s390/qeth: convert remaining legacy cmd callbacks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During vnicc_init wanted_char should be compared to cur_char and not
to QETH_VNICC_DEFAULT. Without this patch there is no way to enforce
the default values as desired values.
Note, that it is expected, that a card comes online with default values.
This patch was tested with private card firmware.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Symptom: After vnicc/rx_bcast has been manually set to 0,
bridge_* sysfs parameters can still be set or written.
Only occurs on HiperSockets, as OSA doesn't support changing rx_bcast.
Vnic characteristics and bridgeport settings are mutually exclusive.
rx_bcast defaults to 1, so manually setting it to 0 should disable
bridge_* parameters.
Instead it makes sense here to check the supported mask. If the card
does not support vnicc at all, bridge commands are always allowed.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Symptom: Error message "Configuring the VNIC characteristics failed"
in dmesg whenever an OSA interface on z15 is set online.
The VNIC characteristics get re-programmed when setting a L2 device
online. This follows the selected 'wanted' characteristics - with the
exception that the INVISIBLE characteristic unconditionally gets
switched off.
For devices that don't support INVISIBLE (ie. OSA), the resulting
IO failure raises a noisy error message
("Configuring the VNIC characteristics failed").
For IQD, INVISIBLE is off by default anyways.
So don't unnecessarily special-case the INVISIBLE characteristic, and
thereby suppress the misleading error message on OSA devices.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_l3_dev_hsuid_store() initially checks the card state, but doesn't
take the conf_mutex to ensure that the card stays in this state while
being reconfigured.
Rework the code to take this lock, and drop a redundant state check in a
helper function.
Fixes: b333293058 ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_l?_set_online() goes through a number of initialization steps, and
on any error uses qeth_l?_stop_card() to tear down the residual state.
The first initialization step is qeth_core_hardsetup_card(). When this
fails after having established a QDIO context on the device
(ie. somewhere after qeth_mpc_initialize()), qeth_l?_stop_card() doesn't
shut down this QDIO context again (since the card state hasn't
progressed from DOWN at this stage).
Even worse, we then call qdio_free() as final teardown step to free the
QDIO data structures - while some of them are still hooked into wider
QDIO infrastructure such as the IRQ list. This is inevitably followed by
use-after-frees and other nastyness.
Fix this by unconditionally calling qeth_qdio_clear_card() to shut down
the QDIO context, and also to halt/clear any pending activity on the
various IO channels.
Remove the naive attempt at handling the teardown in
qeth_mpc_initialize(), it clearly doesn't suffice and we're handling it
properly now in the wider teardown code.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
ENOTSUPP is not uapi, use EOPNOTSUPP instead.
Fixes: d66cb37e96 ("qeth: Add new priority queueing options")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When managing the promiscuous mode during an RX modeset, qeth caches the
current HW state to avoid repeated programming of the same state on each
modeset.
But while tearing down a device, we forget to clear the cached state. So
when the device is later set online again, the initial RX modeset
doesn't program the promiscuous mode since we believe it is already
enabled.
Fix this by clearing the cached state in the tear-down path.
Note that for the SBP variant of promiscuous mode, this accidentally
works right now because we unconditionally restore the SBP role while
re-initializing.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Along with z/VM NICs, there's additional device types that only support
a specific transport mode (eg. external-bridged IQD).
Identify the corresponding error code, and raise a fitting error message
so that the user knows to adjust their device configuration.
On top of that also fix the subsequent error path, so that the rejected
cmd doesn't need to wait for a timeout but gets cancelled straight away.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
The cio layer's intparm logic does not align itself well with how qeth
manages cmd IOs. When an active IO gets terminated via halt/clear, the
corresponding IRQ's intparm does not reflect the cmd buffer but rather
the intparm that was passed to ccw_device_halt() / ccw_device_clear().
This behaviour was recently clarified in
commit b91d9e67e5 ("s390/cio: fix intparm documentation").
As a result, qeth_irq() currently doesn't cancel a cmd that was
terminated via halt/clear. This primarily causes us to leak
card->read_cmd after the qeth device is removed, since our IO path still
holds a refcount for this cmd.
For qeth this means that we need to keep track of which IO is pending on
a device ('active_cmd'), and use this as the intparm when calling
halt/clear. Otherwise qeth_irq() can't match the subsequent IRQ to its
cmd buffer.
Since we now keep track of the _expected_ intparm, we can also detect
any mismatch; this would constitute a bug somewhere in the lower layers.
In this case cancel the active cmd - we effectively "lost" the IRQ and
should not expect any further notification for this IO.
Fixes: 405548959c ("s390/qeth: add support for dynamically allocated cmds")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the RX path builds non-linear skbs, the packet headers can
currently spill over into page fragments. Depending on the packet type
and what fields we need to access in the headers, this could cause us
to go past the end of skb->data.
So for non-linear packets, copy precisely the length of the necessary
headers ('linear_len') into skb->data.
And don't copy more, upper-level protocols will peel whatever additional
packet headers they need.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on a packet's type, the RX path needs to access fields in the
packet headers and thus requires a minimum packet length.
Enforce this length when building the skb.
On the other hand a single runt packet is no reason to drop the whole
RX buffer. So just skip it, and continue processing on the next packet.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Another merge window, another pull full of stuff:
1) Support alternative names for network devices, from Jiri Pirko.
2) Introduce per-netns netdev notifiers, also from Jiri Pirko.
3) Support MSG_PEEK in vsock/virtio, from Matias Ezequiel Vara
Larsen.
4) Allow compiling out the TLS TOE code, from Jakub Kicinski.
5) Add several new tracepoints to the kTLS code, also from Jakub.
6) Support set channels ethtool callback in ena driver, from Sameeh
Jubran.
7) New SCTP events SCTP_ADDR_ADDED, SCTP_ADDR_REMOVED,
SCTP_ADDR_MADE_PRIM, and SCTP_SEND_FAILED_EVENT. From Xin Long.
8) Add XDP support to mvneta driver, from Lorenzo Bianconi.
9) Lots of netfilter hw offload fixes, cleanups and enhancements,
from Pablo Neira Ayuso.
10) PTP support for aquantia chips, from Egor Pomozov.
11) Add UDP segmentation offload support to igb, ixgbe, and i40e. From
Josh Hunt.
12) Add smart nagle to tipc, from Jon Maloy.
13) Support L2 field rewrite by TC offloads in bnxt_en, from Venkat
Duvvuru.
14) Add a flow mask cache to OVS, from Tonghao Zhang.
15) Add XDP support to ice driver, from Maciej Fijalkowski.
16) Add AF_XDP support to ice driver, from Krzysztof Kazimierczak.
17) Support UDP GSO offload in atlantic driver, from Igor Russkikh.
18) Support it in stmmac driver too, from Jose Abreu.
19) Support TIPC encryption and auth, from Tuong Lien.
20) Introduce BPF trampolines, from Alexei Starovoitov.
21) Make page_pool API more numa friendly, from Saeed Mahameed.
22) Introduce route hints to ipv4 and ipv6, from Paolo Abeni.
23) Add UDP segmentation offload to cxgb4, Rahul Lakkireddy"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1857 commits)
libbpf: Fix usage of u32 in userspace code
mm: Implement no-MMU variant of vmalloc_user_node_flags
slip: Fix use-after-free Read in slip_open
net: dsa: sja1105: fix sja1105_parse_rgmii_delays()
macvlan: schedule bc_work even if error
enetc: add support Credit Based Shaper(CBS) for hardware offload
net: phy: add helpers phy_(un)lock_mdio_bus
mdio_bus: don't use managed reset-controller
ax88179_178a: add ethtool_op_get_ts_info()
mlxsw: spectrum_router: Fix use of uninitialized adjacency index
mlxsw: spectrum_router: After underlay moves, demote conflicting tunnels
bpf: Simplify __bpf_arch_text_poke poke type handling
bpf: Introduce BPF_TRACE_x helper for the tracing tests
bpf: Add bpf_jit_blinding_enabled for !CONFIG_BPF_JIT
bpf, testing: Add various tail call test cases
bpf, x86: Emit patchable direct jump as tail call
bpf: Constant map key tracking for prog array pokes
bpf: Add poke dependency tracking for prog array maps
bpf: Add initial poke descriptor table for jit images
bpf: Move owner type, jited info into array auxiliary data
...
- Adjust PMU device drivers registration to avoid WARN_ON and few other
perf improvements.
- Enhance tracing in vfio-ccw.
- Few stack unwinder fixes and improvements, convert get_wchan custom
stack unwinding to generic api usage.
- Fixes for mm helpers issues uncovered with tests validating architecture
page table helpers.
- Fix noexec bit handling when hardware doesn't support it.
- Fix memleak and unsigned value compared with zero bugs in crypto
code. Minor code simplification.
- Fix crash during kdump with kasan enabled kernel.
- Switch bug and alternatives from asm to asm_inline to improve inlining
decisions.
- Use 'depends on cc-option' for MARCH and TUNE options in Kconfig,
add z13s and z14 ZR1 to TUNE descriptions.
- Minor head64.S simplification.
- Fix physical to logical CPU map for SMT.
- Several cleanups in qdio code.
- Other minor cleanups and fixes all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl3ahGYACgkQjYWKoQLX
FBguwAgAig+FNos8zkd7Sr2wg4DPL2IlYERVP40fOLXfGuVUOnMLg8OTO6yDWDpH
5+cKAQS1wWgyvlfjWRUJ6anXLBAsgKRD1nyFIZTpn/wArGk/duCbnl/VFriDgrST
8KTQDJpZ9w9nXtQ7lA2QWaw5U2WG8I2T2JuQJCdLXze7RXi0bDVe8e6131NMaJ42
LLxqOqm8d8XDnd8oDVP04LT5IfhuI2cILoGBP/GyI2fqQk9Ems6M2gxuISq1COmy
WORDLfwWyCLeF7gWKKjxf8Vo1HYcyoFvdXnxWiHb0TDZesQZJr/LLELTP03fbCW9
U4jbXncnnPA7kT4tlC95jT5M69yK5w==
=+FxG
-----END PGP SIGNATURE-----
Merge tag 's390-5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Adjust PMU device drivers registration to avoid WARN_ON and few other
perf improvements.
- Enhance tracing in vfio-ccw.
- Few stack unwinder fixes and improvements, convert get_wchan custom
stack unwinding to generic api usage.
- Fixes for mm helpers issues uncovered with tests validating
architecture page table helpers.
- Fix noexec bit handling when hardware doesn't support it.
- Fix memleak and unsigned value compared with zero bugs in crypto
code. Minor code simplification.
- Fix crash during kdump with kasan enabled kernel.
- Switch bug and alternatives from asm to asm_inline to improve
inlining decisions.
- Use 'depends on cc-option' for MARCH and TUNE options in Kconfig, add
z13s and z14 ZR1 to TUNE descriptions.
- Minor head64.S simplification.
- Fix physical to logical CPU map for SMT.
- Several cleanups in qdio code.
- Other minor cleanups and fixes all over the code.
* tag 's390-5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (41 commits)
s390/cpumf: Adjust registration of s390 PMU device drivers
s390/smp: fix physical to logical CPU map for SMT
s390/early: move access registers setup in C code
s390/head64: remove unnecessary vdso_per_cpu_data setup
s390/early: move control registers setup in C code
s390/kasan: support memcpy_real with TRACE_IRQFLAGS
s390/crypto: Fix unsigned variable compared with zero
s390/pkey: use memdup_user() to simplify code
s390/pkey: fix memory leak within _copy_apqns_from_user()
s390/disassembler: don't hide instruction addresses
s390/cpum_sf: Assign error value to err variable
s390/cpum_sf: Replace function name in debug statements
s390/cpum_sf: Use consistant debug print format for sampling
s390/unwind: drop unnecessary code around calling ftrace_graph_ret_addr()
s390: add error handling to perf_callchain_kernel
s390: always inline current_stack_pointer()
s390/mm: add mm_pxd_folded() checks to pxd_free()
s390/mm: properly clear _PAGE_NOEXEC bit when it is not supported
s390/mm: simplify page table helpers for large entries
s390/mm: make pmd/pud_bad() report large entries as bad
...
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
When propagating IO errors back to userspace, one error path in
qeth_irq() currently returns '1' instead of a proper errno.
Fixes: 54daaca702 ("s390/qeth: cancel cmd on early error")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L2 bridgeport code uses the coarse 'conf_mutex' for guarding access
to its configuration state.
This can result in a deadlock when qeth_l2_stop_card() - called under the
conf_mutex - blocks on flush_workqueue() to wait for the completion of
pending bridgeport workers. Such workers would also need to aquire
the conf_mutex, stalling indefinitely.
Introduce a lock that specifically guards the bridgeport configuration,
so that the workers no longer need the conf_mutex.
Wrapping qeth_l2_promisc_to_bridge() in this fine-grained lock then also
fixes a theoretical race against a concurrent qeth_bridge_port_role_store()
operation.
Fixes: c0a2e4d10d ("s390/qeth: conclude all event processing before offlining a card")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD link group termination is called when peer signals its shutdown
of its corresponding link group. For regular shutdowns no connections
exist anymore. For abnormal shutdowns connections must be killed and
their DMBs must be unregistered immediately. That means the SMCR method
to delay the link group freeing several seconds does not fit.
This patch adds immediate termination of a link group and its SMCD
connections and makes sure all SMCD link group related cleanup steps
are finished.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given the way how the sysfs attributes are registered / unregistered,
the show/store helpers will never be called with a NULL drvdata.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remaining usage effectively is a kmemdup() of the query object.
By not wrapping it, some of the callers can now use GFP_KERNEL for the
allocation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vlan_for_each() instead of tracking each registered VID internally.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code processes each (VLAN) device twice - once to inspect the
IPv4 mcast addresses, and then a second time to walk the IPv6 mcast
addresses. Unify all this into a single helper, thus removing some
checks and a duplicated VLAN lookup.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trust the IPv4/IPv6 code to properly remove its mcast addresses when a
VLAN device is unregistered, and then also trigger an RX modeset
whenever it's needed.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push the inet6_dev locking down into the helper that actually needs it
for walking the mc_list.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_core_free_card() is meant to be the counterpart of
qeth_alloc_card() - but unfortunately was also picked as the place
to free the QDIO queues.
This gets messy when qeth_core_probe_device() fails during
qeth_add_dbf_entry(). At this point the card->qdio.state is not initialized
yet, so qeth_free_qdio_queues() ends up operating on uninitialized data.
Luckily for now, the whole qeth_card struct is zero-allocated and the value
of the QETH_QDIO_UNINITIALIZED enum is 0 as well. So there's no real impact
from this bug at the moment, it's just really fragile.
Clean this up by moving the qeth_free_qdio_queues() call up one level in
the hierarchy. This way it doesn't get called from the error path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When current code fails to allocate an skb in the RX path, it drops the
whole RX buffer. Considering the large number of packets that a single
RX buffer might contain, this is quite drastic.
Skip over the packet instead, and try to extract the next packet from
the RX buffer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets with an unexpected HW format are currently first extracted from
the RX buffer, passed upwards to the layer-specific driver and only then
finally dropped.
Enhance the RX path so that we can drop such packets before even
allocating an skb. For this, add some additional logic so that when a
packet is meant to be dropped, we can still walk along the packet's data
chunks in the RX buffer. This allows us to extract the following
packet(s) from the buffer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each RX buffer may contain up to 64KB worth of data. In case the device
needs to discard a packet _after_ already having reserved space for it
in the buffer, the whole buffer gets set to ERROR state. As the buffer
might contain any number of good packets, this can result in collateral
packet loss.
qeth can provide relief by enabling per-frame invalidation. The RX
buffer is then presented as usual, we just need to spot & drop any
individual packet that was flagged as invalid.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where available, use the fine-grained counters in rtnl_link_stats64 to
indicate different RX error causes. For drop reasons, use driver-private
ethtool counters.
In particular this patch allows us to keep track of driver-side drops due
to unknown/unsupported HW descriptor format.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of storing the multicast-mapped MAC address in an IP address
object, just calculate the MAC address when actually building a cmd
for the IP address.
While at it, also clean up some rather verbose copying of IP addresses.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace our custom implementations with the stack's version of IP address
hashing.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any change to the card state should only be driven by
qeth_l?_set_online() and qeth_l?_stop_card().
qeth_qdio_clear_card() currently also gets called from
(a) qeth_core_shutdown(), where we haven't walked through the whole
teardown sequence. So changing the state to DOWN is not accurate.
(b) qeth_core_hardsetup_card(), which is only called while the card is
still in DOWN state. No change in behaviour here.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting a device online, both subdrivers have the same code to
program the HW trap and Isolation mode. Move that code into a single
place.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When napi_complete_done() returns false, the NAPI instance is still
active and we can keep the IRQ disabled a little longer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qdio.h recently gained a new helper macro that handles wrap-around on a
QDIO queue, consistently use it across all of qeth.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IQD devices with Multi-Write support, we can defer the queue-flush
further and transmit multiple IO buffers with a single TX doorbell.
The same-target restriction still applies.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the Sniffer bit next to all the other CHSC AC2 bits.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Without this patch, a command bit in the supported commands mask is only
ever set to unsupported during set online. If a command is ever marked as
unsupported (e.g. because of error during qeth_l2_vnicc_query_cmds),
subsequent successful initialization (offline/online) would not bring it
back.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Smatch discovered the use of uninitialized variable sup_cmds
in error paths.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The QIB parm area is 128 bytes long. Current code consistently misuses
an _entirely unrelated_ QDIO constant, merely because it has the same
value. Stop doing so.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IQD devices offer limited support for bulking: all frames in a TX buffer
need to have the same target. qeth_iqd_may_bulk() implements this
constraint, and allows us to defer the TX doorbell until
(a) the buffer is full (since each buffer needs its own doorbell), or
(b) the entire TX queue is full, or
(b) we reached the BQL limit.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each TX buffer may contain multiple skbs. So just accumulate the sent
byte count in the buffer struct, and later use the same count when
completing the buffer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows the stack to bulk-free our TX-completed skbs.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to their large MTU and potentially low utilization of TX buffers,
IQD devices in particular require fast TX recycling. This makes them
a prime candidate for a TX NAPI path in qeth.
qeth_tx_poll() uses the recently introduced qdio_inspect_queue() helper
to poll the TX queue for completed buffers. To avoid hogging the CPU for
too long, we yield to the stack after completing an entire queue's worth
of buffers.
While IQD is expected to transfer its buffers synchronously (and thus
doesn't support TX interrupts), a timer covers for the odd case where a
TX buffer doesn't complete synchronously. Currently this timer should
only ever fire for
(1) the mcast queue,
(2) the occasional race, where the NAPI poll code observes an update to
queue->used_buffers while the TX doorbell hasn't been issued yet.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This consolidates the SW statistics code, and improves it to
(1) account for the header overhead of each segment on a TSO skb,
(2) count dangling packets as in-error (during eg. shutdown), and
(3) only count offloads when the skb was successfully transmitted.
We also count each segment of an TSO skb as one packet - except for
tx_dropped, to be consistent with dev->tx_dropped.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d4c08afafa ("s390/qeth: streamline SNMP cmd code") removed
the bounds checking for req_len, under the assumption that the check in
qeth_alloc_cmd() would suffice.
But that code path isn't sufficiently robust to handle a user-provided
data_length, which could overflow (when adding the cmd header overhead)
before being checked against QETH_BUFSIZE. We end up allocating just a
tiny iob, and the subsequent copy_from_user() writes past the end of
that iob.
Special-case this path and add a coarse bounds check, to protect against
maliciuous requests. This let's the subsequent code flow do its normal
job and precise checking, without risk of overflow.
Fixes: d4c08afafa ("s390/qeth: streamline SNMP cmd code")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
