By default, HW link status is up. If hclge_update_link_status is called
before net up, driver will print "link up". It is not suitable. hdev
state check is needed when getting link status.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We clear STATE_DOWN bit of hdev state when starting net, but do not set
it again when stopping net. It causes that the net is down, but hdev state
is still up. STATE_DOWN bit of hdev state should be set when stopping net.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The msix number for vf is different, depends on the max vf number.
Futherly if the vf supports roce, the offset of msix is not fixed.
It's incorrect to fix the msix number to 33. This patch fixes it by
querying the msix number from firmware, and adjusting it with roce
support.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hclgevf_free_vector function expects the caller to pass
the vector_id to it, and hclgevf_put_vector pass vector to
it now, which will cause vector allocation problem.
This patch fixes it by converting vector into vector_id before
calling hclgevf_free_vector.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The payload of mailbox message is 16 byte and the value of
HCLGE_MBX_MAX_ARQ_MSG_SIZE is 8. A message truncated problem will
happen when mailbox message is converted to ARQ message. This patch
replaces HCLGE_MBX_MAX_ARQ_MSG_SIZE with the size of ARQ message in
hclgevf_mbx_handler to fix this problem.
Fixes: b11a0bb231 ("net: hns3: Add mailbox support to VF driver")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency, prefix hnae_ should be modified to hnae3_.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reference to Documentation/DMA-API-HOWTO.txt,
Streaming DMA mappings which are usually mapped for one DMA transfer,
Network card DMA ring descriptors should use Consistent DMA mappings.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some members in struct hns3_enet_tqp_vector, struct hnae3_client
and struct hnae3_ae_algo are unused.
This patch removes them.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hdev->vector_status[vector_id] is already HCLGE_INVALID_VPORT,
should log the error and return.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interface init_client_instance and uninit_client_instance
do not register anything, only initialize the client instance.
This patch rename the related interface to make the function
name to indicate the purpose.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hclge_unmap_ring_frm_vector, there are 2 steps:
step 1: get vector index.
step 2 unbind ring with vector.
But it gets vector id again in step 2 interface. This patch
removes hclge_get_vector_index from hclge_bind_ring_with_vector,
and make the step the same with hns3 PF driver.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the firmware updates the crq's tail pointer, if the VF driver
reads the data in the crq, the data may be incomplete at this time,
which will lead to the driver read an unknown message.
This patch fixes it by checking if crq is empty before reading the
message.
Fixes: b11a0bb231 ("net: hns3: Add mailbox support to VF driver")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VF frequently switches the CMDQ interrupt, if the CMDQ_SRC is not
cleared, the VF will not receive the new PF response after the interrupt
is re-enabled, the corresponding log is as follows:
[ 317.482222] hns3 0000:00:03.0: VF could not get mbx resp(=0) from PF
in 500 tries
[ 317.483137] hns3 0000:00:03.0: VF request to get tqp info from PF
failed -5
This patch fixes this problem by clearing CMDQ_SRC before enabling
interrupt and syncing pending IRQ handlers after disabling interrupt.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last patch apparently added a complete replacement for this
function, but left the old one in place, which now causes a
harmless warning:
drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c:731:12: 'hclgevf_cfg_func_mta_filter' defined but not used
I assume it can be removed.
Fixes: 3a678b5806 ("net: hns3: Optimize the VF's process of updating multicast MAC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the update flow of the new PF driver, if a multicast address is in mta
table, the VF deletion action will not take effect.
This patch adds the VF adaptation according to the new flow of PF'driver.
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Reviewed-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hclge_ae_stop is called during resetting, it will cancel the
service_task by calling cancel_work_sync, which may cause the
service_task to exit without clearing HCLGE_STATE_SERVICE_SCHED
bit. If this happens, the service_task will never run again.
This patch fixes this problem by clearing it after calling
cancel_work_sync in hclge_ae_stop.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for IFF_ALLMULTI flag to HNS3 PF and VF
driver.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When register a RoCE client with hnae3vf device, it needs to judge
the device whether support RoCE vf function. Otherwise, it will
lead to calltrace when RoCE is not support vf function and remove
roce device.
The calltrace as follows:
[ 93.156614] Unable to handle kernel NULL pointer dereference at virtual address 00000015
<SNIP>
[ 93.278784] Call trace:
[ 93.278788] hnae3_match_n_instantiate+0x24/0xd8 [hnae3]
[ 93.278790] hnae3_register_client+0xcc/0x150 [hnae3]
[ 93.278801] hns_roce_hw_v2_init+0x18/0x1000 [hns_roce_hw_v2]
[ 93.278805] do_one_initcall+0x58/0x160
[ 93.278807] do_init_module+0x64/0x1d8
[ 93.278809] load_module+0x135c/0x15c8
[ 93.278811] SyS_finit_module+0x100/0x118
[ 93.278816] __sys_trace_return+0x0/0x4
[ 93.278827] Code: aa0003f5 12001c56 aa1e03e0 d503201f (b9402660)
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Reported-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reported-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vf module is loading, the cmd queue initialization should
happen before misc interrupt initialization, otherwise the misc
interrupt handle will cause using uninitialized cmd queue problem.
There is also the same issue when vf module is unloading.
This patch fixes it by adjusting the location of some function.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hns3 driver has been built into kernel and then loaded with
the same driver which built as KLM, it may trigger an error like
below:
[ 20.009555] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
[ 20.016789] hns3: Copyright (c) 2017 Huawei Corporation.
[ 20.022100] Error: Driver 'hns3' is already registered, aborting...
[ 23.517397] Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[ 23.691583] Process insmod (pid: 1982, stack limit = 0x00000000cd5f21cb)
[ 23.698270] Call trace:
[ 23.700705] __list_del_entry_valid+0x2c/0xd8
[ 23.705049] hnae3_unregister_client+0x68/0xa8
[ 23.709487] hns3_init_module+0x98/0x1000 [hns3]
[ 23.714093] do_one_initcall+0x5c/0x170
[ 23.717918] do_init_module+0x64/0x1f4
[ 23.721654] load_module+0x1d14/0x24b0
[ 23.725390] SyS_init_module+0x158/0x208
[ 23.729300] el0_svc_naked+0x30/0x34
This patch fixes it by adding module version info.
Fixes: 38caee9d3e ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ae_algo is used by many ae_devs. It is not only belong to just a
ae_dev. Initializing ae_dev failed does not represent registering ae_algo
failed. Because the action of registering ae_algo just is adding ae_algo
to the ae_algo list and it is always is true, it make no sense to define
return type as int.
This patch changes the return type of hnae3_register_ae_algo from int to
void.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing ae_dev failed during loading hclge.ko, the drvdata will
be set to null. When removing hns3.ko, we get a null ae_dev. It causes the
null pointer problem.
This patch removes pci_set_drvdata from error handle of hclge_init_ae_dev
to fix the bug, since pci_set_drvdata has been called in hns3_remove.
Also, we do not need to uninit the ae_dev which is not initialized. And
it may be the one which is initialized failed.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of hardware rx-vlan-offload to VF driver.
VF uses mailbox to convey PF to configure the hardware.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset Asserting message is forwarded by PF to inform VF about
the hardware reset which is about to happen. This might be due
to the earlier VF reset request received by the PF or because PF
for any reason decides to undergo reset. This message results in
VF to go in pending state in which it polls the hardware to
complete the reset and then further resets/tears its own stack.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current mailbox CRQ could consists of both synchronous and async
responses from the PF. Synchronous responses are time critical
and should be handed over to the waiting tasks/context as quickly
as possible otherwise timeout occurs.
Above problem gets accentuated if CRQ consists of even single
async message. Hence, it is important to have quick handling of
synchronous messages and maybe deferred handling of async messages
This patch introduces separate ARQ(async receive queues) for the
async messages. These messages are processed later with repsect
to mailbox task while synchronous messages still gets processed
in context to mailbox interrupt.
ARQ is important as VF reset introduces some new async messages
like MBX_ASSERTING_RESET which adds up to the presssure on the
responses for synchronousmessages and they timeout even more
quickly.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the hardware reset we should re-fetch the configuration from
PF like queue info and tc info. This might have impact on allocations
made like that of TQPs. Hence, we should release all such allocations
and re-allocate fresh according to new fetched configuration after
reset.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After VF driver knows that hardware reset has been performed
successfully, it should proceed ahead and reset the enet layer.
This primarily consists of bringing down interface, clearing
TX/RX rings, disassociating vectors from ring etc.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF driver depends upon PF to eventually reset the hardware. This
request is made using the mailbox command. This patch adds the
required function to acheive above.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces the hclge device reset states of "requested" and
"pending" and also its handling in context to Reset Service Task.
Device gets into requested state because of any VF reset request
asserted from upper layers, for example due to watchdog timeout
expiration. Requested state would result in eventually forwarding
the VF reset request to PF which would actually reset the VF.
Device will get into pending state if:
1. VF receives the acknowledgement from PF for the VF reset
request it originally sent to PF.
2. Reset Service Task detects that after asserting VF reset for
certain times the data-path is not working and device then
decides to assert full VF reset(this means also resetting the
PCIe interface).
3. PF intimates the VF that it has undergone reset.
Pending state would result in VF to poll for hardware reset
completion status and then resetting the stack/enet layer, which
in turn means reinitializing the ring management/enet layer.
Note: we would be adding support of 3. later as a separate patch.
This decision should not affect VF reset as its event handling
is generic in nature.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF reset would involve handling of different reset related events
from the stack, physical function, mailbox etc. Reset service task
would be used in servicing such reset event requests and later
handling the hardware completions waits and initiating the stack
resets.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 drivers enet layer, used for the ring management and stack
interaction, is common to both VF and PF. PF already supports reset
functionality to handle the network stack watchdog timeout trigger
but the existing code is not generic enough to be used to support VF
reset as well.
This patch does following:
1. Makes the existing watchdog timeout handler in enet layer generic
i.e. suitable for both VF and PF and
2. Introduces the new reset event handler for the VF code.
3. Changes existing reset event handler of PF code to initialize the
reset level
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for querying speed and duplex by ethtool ethX
to VF.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ethtool_ops.get_link support to VF.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may need more time for IMP handle some command, such as reset.
This patch enlarges the max time for cmd timeout.
Driver will check the IMP result every us, it may break through the
loop when get the right result. So not all command need the max time.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no module that is dependent on hclge or hclgevf's symbol,
but hns_enet need them to provide ops for it to run. When there is
a need to auto load the hns3 driver, the auto load will fail because
hclge or hclgevf is not loaded.
Hns_enet has already exported the pci table, so this patch exports
the pci table for hclge and hclgevf module too.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF queue reset flow is different from PF queue reset flow.
VF driver should stop VF queue first, then send message to PF
and PF do the reset. PF should send a response to VF after
PF complete the queue reset, VF can initialize the queue hw
after get the response.
This patch fixes the VF queue reset flow as the correct step.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF changes unicast mac address by sending mailbox msg to PF, then PF
completes the mac address modification. It may fail when the target
uc mac address is already in the mac_vlan table. VF should be aware
of it by reading the message result.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the buffer overflow warning by refactoring
hclgevf_bind_ring_to_vector and hclge_get_ring_chain_from_mbx.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Fixes: dde1a86e93 ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status update function is called by timer every second. But
net_stop and net_open may be called with very short intervals. The link
status update function can not detect the link state has changed. It
causes the netdev not running problem.
This patch fixes it by updating the link state in ae_stop function.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver is in initial state, the mac_vlan table table is empty.
So the delete operation for mac address must fail. Existence check
is needed here. Otherwise, the error message will make user confused.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a get_vector function, which allocate the vectors
for a client, but there is not a put_vector to free the
vector.
This patch introduces the put_vector function in order to
fix the coalesce configuration lost problem during reset
process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for VF driver inner interface
hclgevf_ops.get_tqps_and_rss_info. This interface will be
used in the initialization process.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver check the out_vld bit when get a new cmdq BD, if the bit is 1,
the BD is valid. driver Should set the bit 0 after used and hw will
set the bit 1 if get a valid BD.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like PF, if the int_gl_idx of VF does not be set, the default
interrupt coalesce index of VF is 0. But it should be GL1 for TX
queues and GL0 for RX queues.
This patch adds the int_gl_idx setup for VF.
Fixes: 200ecda42598 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only main PF can config TSO MSS length according to hardware.
This patch removes TSO config command from VF driver.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch supports the ethtool's get_channels() for VF.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a redundant semicolon, this patch removes it.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The result of tqp statistics query was read with an
error position, fix it according to the user manual.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some members of packet statistics are named in different styles.
This patch unifies them with new internal name rules, the main
modification are below:
trans --> tx
rcv --> rx
rcb_q%d_tx --> txq#%d
rcb_q%d_rx --> rxq#%d
sw_err_cnt(tx side) --> tx_dropped
sw_err_cnt(rx side) --> rx_dropped
pkts --> packets
tx_err_cnt --> errors
rx_err_cnt --> errors
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the NAPI handling interface, skb buffer management,
management of the RX/TX descriptors, ethool interface etc.
has quite a bit of code which is common to VF and PF driver.
This patch makes the exisitng PF's HNS3 ENET driver as the
common ENET driver for both Virtual & Physical Function. This
will help in reduction of redundancy and better management of
code.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
