Salil Mehta says:
====================
Misc. bug fixes & small enhancements for HNS3 Driver
This patch-set presents some fixes and minor enhancements to HNS3 Driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous implement, the query operation for fibre port and copper
port are mixed. This patch refines it by seperating them based on the port
type.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the advertised flow control ability has been fetched using
phy_ethtool_ksettings_get() or hclge_get_link_mode() then it is
unnecessary to fetch them again later using hclge_get_flowctrl_adv().
This patch removes it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the dst mac addr of loopback packet is the same as
the host' mac addr, the SSU component may loop back the packet
to host before the packet reaches mac or serdes, which will defect
the purpose of mac or serdes selftest.
This patch changes it by adding 0x1f to the last byte of dst mac
addr.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only fiber port checks if it is necessay to set the
mac through firmware when link is changed, this patch unify the
checking to allow the copper port do the checking too.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netdev is down, the stack will delete the vlan from
hardware including vlan0, which will cause problem when
doing loopback selftest when netdev is down.
This patch fixes it by always preserving vlan 0 in hardware,
because vlan 0 is defalut vlan, which should always be in
hardware.
Fixes: c39c4d98dc ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ping is runnig and user executes the loopback selftest, the
ping cmd will stop and exit.
This patch fixes it by using the hns3_nic_net_open/stop to offline
the netdev when doing loopback selftest.
Fixes: c39c4d98dc ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tqp and mac need to be enabled when doing loopback selftest,
ae_algo->ops->start/stop is used to do the job, there is a
time window between ae_algo->ops->start/stop and loopback setup,
which will cause selftest failed problem when there is frame
coming in during that time window.
This patch fixes it by enabling the tqp and mac during loopback
setup process.
Fixes: c39c4d98dc ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements shutdown ops in hns3 pci driver, which
unloads the hns3 driver and set the power state to D3hot.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF uses hdev->vlan_table to manage the port vlan table. In function
hclge_set_vlan_filter_hw(), it checks whether a vlan id has been used,
by foreach all the vport bits. It should use macro HCLGE_VPORT_NUM,
not VLAN_N_VID as the foreach condition.
Fixes: 6c251711b3 ("net: hns3: Disable vf vlan filter when vf vlan table is full")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the lower 24 bits of the IPV6 link-local addresses at both
ends are the same, the multicast MAC address for Neigbour Discovery
is the same. The multicast for Neigbour Discovery will fail.
This patch fixes it by including the bonding uplink port in the
multicast group.
Fixes: 46a3df9f9718("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are only 128 entries in vf vlan table, if user has added
more than 128 vlan, fw will ignore it and disable the vf vlan
table. So when user deletes the vlan entry that has not been
set to vf vlan table, fw will return not found result and driver
treat that as error, which will cause vlan delete failed problem.
This patch fixes it by returning ok when fw returns not found
result.
Fixes: 6c251711b3 ("net: hns3: Disable vf vlan filter when vf vlan table is full")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix for two spelling mistakes.
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Bug fixes.
This short series fixes resource related logic in the driver, mostly
affecting the RDMA driver under corner cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver adjusts the bp->hw_resc.max_cp_rings by the number
of MSIX vectors used by RDMA. There is one code path in open that needs
to check the true max_cp_rings including any used by RDMA. This code
is now checking for the reduced max_cp_rings which will fail when the
number of cp rings is very small.
To fix this in a clean way, we don't adjust max_cp_rings anymore.
Instead, we add a helper bnxt_get_max_func_cp_rings_for_en() to get the
reduced max_cp_rings when appropriate.
Fixes: ec86f14ea5 ("bnxt_en: Add ULP calls to stop and restart IRQs.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused bnxt_subtract_ulp_resources(). Change
bnxt_get_max_func_irqs() to static since it is only locally used.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver detects that resources have changed during open, it
should reset the rx and tx rings to 0. This will properly setup the
init sequence to initialize the default rings again. We also need
to signal the RDMA driver to stop and clear its interrupts. We then
call the RoCE driver to restart if a new set of default rings is
successfully reserved.
Fixes: 25e1acd6b9 ("bnxt_en: Notify firmware about IF state changes.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long says:
====================
sctp: two fixes for spp_ipv6_flowlabel and spp_dscp sockopts
This patchset fixes two problems in sctp_apply_peer_addr_params()
when setting spp_ipv6_flowlabel or spp_dscp.
====================
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When users set params.spp_address and get a trans, ipv6_flowlabel flag
should be applied into this trans. But even if this one is not an ipv6
trans, it should not go to apply it into all other transes of the asoc
but simply ignore it.
Fixes: 0b0dce7a36 ("sctp: add spp_ipv6_flowlabel and spp_dscp for sctp_paddrparams")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in sctp_apply_peer_addr_params(), if SPP_IPV6_FLOWLABEL flag is set
and trans is NULL, it would use trans as the index variable to traverse
transport_addr_list, then trans is set as the last transport of it.
Later, if SPP_DSCP flag is set, it would enter into the wrong branch as
trans is actually an invalid reference.
So fix it by using a new index variable to traverse transport_addr_list
for both SPP_DSCP and SPP_IPV6_FLOWLABEL flags process.
Fixes: 0b0dce7a36 ("sctp: add spp_ipv6_flowlabel and spp_dscp for sctp_paddrparams")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__emac_calc_base_mr1 was used instead of __emac4_calc_base_mr1
by copy-paste mistake for emac4syn.
Fixes: 45d6e54550 ("net/ibm/emac: add 8192 rx/tx fifo size")
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the following obsolete parameter comments of tipc_topsrv struct:
@rcvbuf_cache
@tipc_conn_new
@tipc_conn_release
@tipc_conn_recvmsg
@imp
@type
Add the comments for the missing parameters below of tipc_topsrv struct:
@awork
@listener
Remove the unused or duplicated parameter comments of tipc_conn struct:
@outqueue_lock
@rx_action
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The _IOC_READ flag fits this ioctl request more because this request
actually only writes to, but doesn't read from userspace.
See NOTEs in include/uapi/asm-generic/ioctl.h for more information.
Fixes: 429711aec2 ("vhost: switch to use new message format")
Signed-off-by: Gleb Fotengauer-Malinovskiy <glebfm@altlinux.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pradeep Nalla <pradeep.nalla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This card identifies itself as:
Ethernet controller [0200]: NCube Device [10ff:8168] (rev 06)
Subsystem: TP-LINK Technologies Co., Ltd. Device [7470:3468]
Adding a new entry to rtl8169_pci_tbl makes the card work.
Link: http://launchpad.net/bugs/1788730
Signed-off-by: Anthony Wong <anthony.wong@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
man ip-tunnel ttl section says:
0 is a special value meaning that packets inherit the TTL value.
IPv4 tunnel respect this in ip_tunnel_xmit(), but IPv6 tunnel has not
implement it yet. To make IPv6 behave consistently with IP tunnel,
add ipv6 tunnel inherit support.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tracing is enabled, all the debug messages are recorded and must
not exceed MAX_MSG_LEN (100) columns. Longer debug messages grant the
user with:
WARNING: CPU: 3 PID: 32642 at /tmp/wifi-core-20180806094828/src/iwlwifi-stack-dev/net/mac80211/./trace_msg.h:32 trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211]
Workqueue: phy1 ieee80211_iface_work [mac80211]
RIP: 0010:trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211]
Call Trace:
__sdata_dbg+0xbd/0x120 [mac80211]
ieee80211_ibss_rx_queued_mgmt+0x15f/0x510 [mac80211]
ieee80211_iface_work+0x21d/0x320 [mac80211]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver fails to properly prepare for the channel
switch, mac80211 will disconnect. If the CSA IE had mode
set to 1, it means that the clients are not allowed to send
any Tx on the current channel, and that includes the
deauthentication frame.
Make sure that we don't send the deauthentication frame in
this case.
In iwlwifi, this caused a failure to flush queues since the
firmware already closed the queues after having parsed the
CSA IE. Then mac80211 would wait until the deauthentication
frame would go out (drv_flush(drop=false)) and that would
never happen.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When performing a channel switch flow for a managed interface, the
flow did not update the bandwidth of the AP station and the rate
scale algorithm. In case of a channel width downgrade, this would
result with the rate scale algorithm using a bandwidth that does not
match the interface channel configuration.
Fix this by updating the AP station bandwidth and rate scaling algorithm
before the actual channel change in case of a bandwidth downgrade, or
after the actual channel change in case of a bandwidth upgrade.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We hit a problem with iwlwifi that was caused by a bug in
mac80211. A bug in iwlwifi caused the firwmare to crash in
certain cases in channel switch. Because of that bug,
drv_pre_channel_switch would fail and trigger the restart
flow.
Now we had the hw restart worker which runs on the system's
workqueue and the csa_connection_drop_work worker that runs
on mac80211's workqueue that can run together. This is
obviously problematic since the restart work wants to
reconfigure the connection, while the csa_connection_drop_work
worker does the exact opposite: it tries to disconnect.
Fix this by cancelling the csa_connection_drop_work worker
in the restart worker.
Note that this can sound racy: we could have:
driver iface_work CSA_work restart_work
+++++++++++++++++++++++++++++++++++++++++++++
|
<--drv_cs ---|
<FW CRASH!>
-CS FAILED-->
| |
| cancel_work(CSA)
schedule |
CSA work |
| |
Race between those 2
But this is not possible because we flush the workqueue
in the restart worker before we cancel the CSA worker.
That would be bullet proof if we could guarantee that
we schedule the CSA worker only from the iface_work
which runs on the workqueue (and not on the system's
workqueue), but unfortunately we do have an instance
in which we schedule the CSA work outside the context
of the workqueue (ieee80211_chswitch_done).
Note also that we should probably cancel other workers
like beacon_connection_loss_work and possibly others
for different types of interfaces, at the very least,
IBSS should suffer from the exact same problem, but for
now, do the minimum to fix the actual bug that was actually
experienced and reproduced.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit 9236c4523e5b ("mac80211: limit wmm params to comply
with ETSI requirements"), we have limited the WMM parameters to
comply with 802.11 and ETSI standard. Mistakenly the TXOP value
was caluclated wrong. Fix it by taking the minimum between
802.11 to ETSI to make sure we are not violating both.
Fixes: e552af0581 ("mac80211: limit wmm params to comply with ETSI requirements")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "chandef->center_freq1" variable is a u32 but "freq" is a u16 so we
are truncating away the high bits. I noticed this bug because in commit
9cf0a0b4b6 ("cfg80211: Add support for 60GHz band channels 5 and 6")
we made "freq <= 56160 + 2160 * 6" a valid requency when before it was
only "freq <= 56160 + 2160 * 4" that was valid. It introduces a static
checker warning:
net/wireless/util.c:1571 ieee80211_chandef_to_operating_class()
warn: always true condition '(freq <= 56160 + 2160 * 6) => (0-u16max <= 69120)'
But really we probably shouldn't have been truncating the high bits
away to begin with.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Initialize 'n' to 2 in order to take into account also the first
packet in the estimation of max_subframe limit for a given A-MSDU
since frag_tail pointer is NULL when ieee80211_amsdu_aggregate
routine analyzes the second frame.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few fixes for the fallout of being a little more pedantic about
dma masks.
-----BEGIN PGP SIGNATURE-----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=GFai
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.19-2' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"A few fixes for the fallout of being a little more pedantic about dma
masks"
* tag 'dma-mapping-4.19-2' of git://git.infradead.org/users/hch/dma-mapping:
of/platform: initialise AMBA default DMA masks
sparc: set a default 32-bit dma mask for OF devices
kernel/dma/direct: take DMA offset into account in dma_direct_supported
Tariq Toukan says:
====================
mlx5e IPoIB stats
This patchset by Feras contains statistics enhancements and NDO
implementation for the mlx5e IPoIB driver.
Series generated against net-next commit:
2d5c288598 net: bgmac: remove set but not used variable 'err'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the RQs are shared between all pkey interfaces, the stats
should be taken from where the per-ring stats are stored instead
of the parent RQ.
Fixes: 4c6c615e3f ("net/mlx5e: IPoIB, Add PKEY child interface nic profile")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose RX and TX counters by implementing ndo_get_stats64 operation
for child devices.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose RX and TX counters by implementing ndo_get_stats64 operation for
both parent devices.
After this change, all the relevant statistics can be retrieved using
ifconfig.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhanced ipoib does not initialize max_opened_tc causing wrong ethtool
statistics. As mlx5e_grp_sw_update_stats relies on this variable, without
this change, the TX statistics will not be updated.
Fixes: 05909babce ("net/mlx5e: Avoid reset netdev stats on configuration changes")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
Full phylink support for mv88e6352
These two patches implement full phylink support for the mv88e6352
family, when using an SFP connected to its SERDES interface. This adds
interrupt support to the SERDES, so that we get interrupts on link
up/down, and then make calls phydev_link_change().
The first patch is a minor bug fix, which does not seem to affect any
current features, so i'm not submitting it for stable. It is however
required for configuring SERDES interrupts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6352 family has one SERDES interface, which can be used by either
port 4 or port 5. Add interrupt support for the SERDES interface, and
report when the link status changes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After changing to the needed page, actually write the value to the
register!
Fixes: 09cb7dfd3f ("net: dsa: mv88e6xxx: describe PHY page and SerDes")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include linux/in6.h for struct in6_addr.
/usr/include/linux/rds.h:156:18: error: field ‘laddr’ has incomplete type
struct in6_addr laddr;
^~~~~
/usr/include/linux/rds.h:157:18: error: field ‘faddr’ has incomplete type
struct in6_addr faddr;
^~~~~
/usr/include/linux/rds.h:178:18: error: field ‘laddr’ has incomplete type
struct in6_addr laddr;
^~~~~
/usr/include/linux/rds.h:179:18: error: field ‘faddr’ has incomplete type
struct in6_addr faddr;
^~~~~
/usr/include/linux/rds.h:198:18: error: field ‘bound_addr’ has incomplete type
struct in6_addr bound_addr;
^~~~~~~~~~
/usr/include/linux/rds.h:199:18: error: field ‘connected_addr’ has incomplete type
struct in6_addr connected_addr;
^~~~~~~~~~~~~~
/usr/include/linux/rds.h:219:18: error: field ‘local_addr’ has incomplete type
struct in6_addr local_addr;
^~~~~~~~~~
/usr/include/linux/rds.h:221:18: error: field ‘peer_addr’ has incomplete type
struct in6_addr peer_addr;
^~~~~~~~~
/usr/include/linux/rds.h:245:18: error: field ‘src_addr’ has incomplete type
struct in6_addr src_addr;
^~~~~~~~
/usr/include/linux/rds.h:246:18: error: field ‘dst_addr’ has incomplete type
struct in6_addr dst_addr;
^~~~~~~~
Fixes: b7ff8b1036 ("rds: Extend RDS API for IPv6 support")
Signed-off-by: Vinson Lee <vlee@freedesktop.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cp_hashinfo.ehash_mask is always an odd number, which is set in function
alloc_large_system_hash(). See bellow,
if (_hash_mask)
*_hash_mask = (1 << log2qty) - 1; <<< always odd number
Hence the local variable 'cnt' is a even number, as a result of that it is
no difference to do the incrementation here.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Kconfig warning with OF_MDIO where OF_MDIO was
selected unconditionally instead of only when
OF is actually enabled.
Fixes 7e8d5755be ("net: nixge: Add support for 64-bit platforms")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel module may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.16 are:
[FUNC] usleep_range
drivers/net/ethernet/cadence/macb_main.c, 648:
usleep_range in macb_halt_tx
drivers/net/ethernet/cadence/macb_main.c, 730:
macb_halt_tx in macb_tx_error_task
drivers/net/ethernet/cadence/macb_main.c, 721:
_raw_spin_lock_irqsave in macb_tx_error_task
To fix this bug, usleep_range() is replaced with udelay().
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-09-02
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix one remaining buggy offset override in sockmap's bpf_msg_pull_data()
when linearizing multiple scatterlist elements, from Tushar.
2) Fix BPF sockmap's misuse of ULP when a collision with another ULP is
found on map update where it would release existing ULP. syzbot found and
triggered this couple of times now, fix from John.
3) Add missing xskmap type to bpftool so it will properly show the type
on map dump, from Prashant.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
